How to cut a disk saw diold. How to remove Diold DP 1.6-190 on the circular

How to use a manual circular saw. secrets and techniques of proper and safe work with a dangerous tool

A manual circular saw, like any other automatic manual tool, is a device, the use of which is associated with certain risks and dangers. First of all, there is a real possibility of damage to the body with a sharp saw disc, in addition, the workpiece itself for the saw can lead itself inadequately and injure.

To avoid possible injury, we will present in the article all the rules and methods of safe work with a manual circular saw.

Safety precautions when working with a manual disc with wood

Safety measures when working with a manual tool include a whole range of measures, which consists of checking the equipment, its preparation, trial starting, and providing yourself with a safe workplace.

Preparation of the tool

The preparation of a manual circular saw includes the following measures, by the way, these actions are relevant for a stationary circular:

• The disk is securely attached to the planting spindle and tightened with a flat nut. For this, a special key is used, which is supplied to the device. As a rule, the threading of the nut has the opposite direction to the rotation of the circular disk. Thus, the nut goes “in a delay” when working.
• A special casing is put on the disk, which closes its upper. non.working or “dead” part and leaves the bottom of the disk open.
• Now you can turn on the circular, reliably holding it in your hands. Trial rotation is given. The circular should not vibrate and make extraneous sounds.

If, nevertheless, with a trial start, vibration and extraneous noises occur, then the circular stops, the puff of the disk is checked. If, after repeatedly, the signs of unsatisfactory work are repeated, then the problem is in the mechanism of circular saw. It is strictly forbidden to work with such a tool.

Important! It is forbidden to work with a saw without stopping. this gives an excessive load on the engine, which leads to overheating and early failure.

Preparation of the workplace

First of all, the workplace should not be cluttered. Cuts are made on a convenient and stable workbench or table. The workpiece should evenly lie on the surface of the table.

The thickness of the table should allow fixing the tree under the cut with a clamp or a vice. It is forbidden to hold the workpiece with your hands independently or with the help of unauthorized persons. The exception is only the method of working on a stationary circular, when the workpiece manually is filed to the disk.

In addition, the workplace should be quite illuminated, ventilated and allow the free movement of the master around the workbench.

Blanks, what should be, what can be sawed and what is categorically impossible?

A manual circular saw is designed for a cut of sheet wood, plywood, timber and individual boards, but there are a number of restrictions.

• Prefabricated panels, such. Since the closing place of the cluster will be picked up and thrown out by the saw.
• Wooden sheets with metal pins.

As for the metal, using special equipment. disks with small teeth, you can saw an aluminum profile. But it is strictly forbidden to saw steel, cast iron and other durable metals.

It is allowed to cut the metal wire “rollers”, thin reinforcing bar and ceramic tiles. But at the same time, the replaced disk will quickly become unusable. It is best to use an angular grinder with a cutting disk or electric welding for cutting metal.

How to keep it right?

There is a specific regulation when working with manual saw tools, it fully reflects the work methodology.

To work with a manual circular saw, there are a number of mandatory rules:

• The tool is firmly and reliably held. At the same time, there is one important nuance. a manual circular has only one hand for the right hand, the left hand falls on the top of the protective casing. With the right hand, the tool is submitted in the direction of the cut, and the left is centered and pressed to the workpiece. Hold the circular with one hand is prohibited. Larger models of circulars are equipped with a side guide handle.
• You need to stand on the side of the cut. It is strictly forbidden to lead the circular saw on itself. All movements are made forward from itself, and the master himself stands on the side of the workpiece.

The same techniques are used for stationary circular saws and manual corner grinders (Bulgarian).

The set of tools necessary to replace

When failing of the saw disk of a hand disco, it must be replaced. This does not require special technical skills and the presence of a special tool.

As a rule, the necessary set consists of several hexagons and is included in the set of delivery.

Safety precautions during installation

The presence of a rotating cutting element makes a manual disc saw an instrument of increased danger. Therefore, when replacing the saw disk, the following safety regulations must be followed:

• Disconnect the tool from the power supply network. During the replacement of the disk there is a chance of random pressing the launch key, as a result of which irreparable damage to the health of the user can be caused;
• Check the fixing nut and shaft for the presence of deformations and chips. Their presence can lead to accidental disconnecting of the disk during operation and harm to the health of the operator;
• replace in special gloves. This will protect the hands from cuts and abrasions.

Replacing Interskol 190

As well as on other models of circular saws presented on the domestic tool market, the mounting of the Interskol 190 saw disk is represented by a self.tightening central screw.

How to unscrew and remove from a manual circular, and also in which direction is unscrewed

To replace the saw disk, the following actions must be performed:

To ensure security, the fixing nut is equipped with left thread. This allows her to drag on during sawing. Therefore, unscrewing the nut must be done counterclockwise.

How to install it correctly

The installation of a saw disk begins with the choice of the right direction of rotation. To do this, the arrows indicating the direction of the saw. Their directions must coincide.

The installation and fixation of the disk is carried out in the following order:

After that, you can connect the tool to the AC network and start working with a circular.

To facilitate the unscrewing of the fixation bolt, before twisting, it is best to put a small fragment of office paper under it.

After watching the video, you can familiarize yourself with the procedure for dismantling and installing a saw disk on a manual circular Interskol DP190 in more detail.

What to do if not unscrewed

In the process of sawing wood, the disk can face more dense material, such as knots or metizes. As a result, short.term jamming of the disk occurs and spindle turning. This leads to a stronger tightening of the fixation bolt.

In order to unscrew such a bolt, you need to treat it with a deep penetration grease, for example WD-40. Further unscrewing must be performed using a rug bolt with an elongated handle (lever).

Reviews

Let’s see the reviews of real users of this model that I found on the Internet. First I will tell you the negative:

• Very short wire, and even plastic.
• Weak stamped metal base.
• Noisy.
• At first, the brushes were very tagged.
• The build quality is lame.

Perhaps you will become the owner of this model of a disc saw, you can share your review in the Комментарии и мнения владельцев.

Capabilities

The brush engine with a capacity of 1400 watts is reliable and efficient when working with any tree breeds. The maximum number of revolutions made by the disk per minute of the continuous operation of the disc saw reaches 5000. The maximum sawing depth of 90 ° is 55 mm.

The device has protection against accidental inclusion, which is especially true if children can get access to the power tool. The tool disk is covered with a casing, so that the user is protected from sawdust and sparks. Due to the possibility of the operation of a disk saw with a guide bus, high accuracy of the cut is ensured along the entire length.

• Double isolation.
• Protection against radio interference.
• Possibility of draining.
• Involuntary power protection.
• Forced cooling. overheating protection.

Reviews

Let’s see the reviews of real users of this model that I found on the Internet. First I will tell you the negative:

• There are not enough holes in the sole for attaching to the table.
• The protective casing is unstably opened, jams.
• The casing is stupid.
• Luftitis casing is protection.
• The blade of the disk for aiming sawing is not visible.
• Clamping handles seem to be flimsy.
• The clamp does not fix the angle of inclination.
• Oak cable, in the cold is very hard.
• It has a good saw.
• Very convenient flags for adjusting the angles and depth of drink.
• The power and depth of the cut is enough for everything.
• The side line is strong.
• The depthmer is clearly visible.
• Adequate price for the declared characteristics.
• Metal base and protection of the saw disk.
• Light weight.
• Convenient in the hand.

Perhaps you will become the owner of this model of a disc saw, you can share your review in the Комментарии и мнения владельцев.

Diold disco saws 2022

Analyzing 11 pcs. goods in the category DIOLD DISK PILS, our experts compared their characteristics, customer reviews, for Diold disc saws, as well as the pros and cons of each product and formed the top 10 best in the price/quality ratio. With the help of our rating, you can independently compare all the characteristics and of Brand Diold products before purchasing.

We offer to study all the pros and cons of the buyers in the reviews of the product DIOLD DP-2,4-235 DIOLD

Useful reviews of the owners

Power, affordable price, successful configuration of clamps for working in stationary mode, large diameter of the saw disk.

Low quality of material, constructive flaws.

Before buying this saw, work experience with disc saws 5 years. DP-2,4-235P bought for summer construction needs, t.to. It became missing the depths of the cut. Saw constructively “raw”. When working in stationary mode, the casing space is quickly clogged with sawdust, the safety visor jams and it stops leaving. Constantly because of this you have to interrupt the work, remove the saw and clean. Extremely low quality manufacturing material: the coating on the sole was erased after the first use of the saw (assignment of 3 boards). Also, at the first use in mobile mode, the switch lock button flew along with the spring. The screw for the angle of the boost angle is constantly unscrewed from vibration. From the saw, during operation, it smells suspiciously overheated wiring, and when the low load or duration is operated, the engine cover is significantly heated. The food wire is short and hard, as a result of which it strives to get under the disk, you must be more careful. Classification of inclusion in stationary mode. It’s just something! The button would be much more convenient than sticking, dripping a saw from a socket every time. The guide neckline in the sole is very small, when sawing the markup, it is hard to see it through it, so it instantly clogs with sawdust, which have to be blown away. And the largest constructive error. This is too wide a gap in the sole for disk. When sawing narrow rails at the output sometimes clamps and hits the material, it is extremely unpleasant and unsafe.

Reviews DILD DP-1,3-160

I bought Piludiold DP-1.3-160 in 2010. He sawed the boards.slate flat and wave.Metal distribution. Pipes.brick. Changed only the discs according to the material. It worked at times almost all day with a smoke break for me 5-10min. for 2-3 hours of continuous work.Last 2017, I changed the brushes to the spare ones from the kit.After 3-4 hours, power was lost.It turned out the brushes ended.Put it from the vacuum cleaner.For almost a year now everything is the norm with this.She became noisy.The gearbox has been settled.I think it’s time to think about replacing.I want with the possibility of a hospital.I will watch Diold.

After so many years of merciless operation (took hastily cheaper) still lively.25-30 cubes of the horseman are mostly solid rocks on firewood, not counting much more annually.Reliable inexpensive unpretentious.

Electro-shnur short and hard.The sole is weak. Sharp start. He worked with old boards, there are no nails, he chose the disk, bought a new one (problem, there is no 160 20), I can’t replace who will tell you how to do it.Bolt M816 does not turn away in any

Really cheap and light. The lack of a warranty workshop can be added to the advantages, because we would not get out of there. The quality of the assembly and materials delivers.Food cord non.working, short and hard. From the old corner grinder, a rubber five.meter rubber.The base is stamped from the sheet, there is not enough stiffness, the parallel emphasis will be eliminated, the casing dangles.He conducted after.sales training, as they say, replaced bolts, replaced the spring, the sole fished out.The sole was advised to make it from the sheet himself thicker, while only the drawing prepared. At the same time I plan to clue the smooth start. If half I do this saw, then what I paid for the money?

The base is not tough enough, bends. Parallel emphasis shifts. The food wire is short. The protective casing began to hang out over time.After I discovered that we have no guarantors, it became easier. Jammed the saw. stopped spinning. Made for money. Everything else did himself. The wire replaced with a long rubber. The spring on which the casing was pulled up was replaced. The screws for the side guide replaced, began to drag on tightly.In general, he put his hands a little, everything was better. The only question is why the hands at the factory were not attached?

The spring casing spring stretched out in a year, I had to change. Hard wire even in a small frost.

I bought in 2012. I survived the construction of the house and a bunch of boards with nails. Most likely, from a worn sawy disk that stuck in the propyle during the dissolution of the board 50s on the bars, she died.

It was necessary to make grooves and sample in the beam. There is Makita 5903R weighing 7.5 kg. although good, but hands fall off. Diold took weight and price for one.time work on the calculation. so as not to sorry to throw it out. Worked with a bang and remained alive. Now Makita has registered in the table (hospital), and this diold for handmade, did not expect such survivability and amenities. Very convenient, saws excellent.

A very short wire and even plastic, you have to immediately change the required length for rubber kg.A weak stamped metal base, easily bends from pressing, because of which the sawn was not at 90 degrees.Noisy. Although noisy all disk saws.At first, the brushes were very twisted, then they stopped, probably got sick.

This is my first disk saw. I decided to try what kind of beast it was, so I bought an inexpensive for a sample. It turned out the tool really necessary and useful. You can work, but you need to finalize the saw itself (“collective farm”). The wire changed to a five.meter rubber, and the base was amplified by a plate of polished textolite (thickness 5mm.) In addition, I installed a smooth start block in the handle. After all the improvements it seemed to be normal.I ask myself why buy cheapness, so that then bother so much!? I use Boshevsky discs, I never saved on consumption. That’s in general then and all. I will take the next saw only a brand manufacturer and always with a cast platform.Good luck everyone!

Reviews DILD DP-2.0-200

The standard disk hits a little when working, respectively, the cut is not clean at all. After a couple of months, car engines on the disk were twisted, now it does not open until the end, you have to make efforts at the end, unpleasant.

Power. Good motor. The depth drank. Similar equipment: nozzle for a vacuum cleaner, a wedging knife, clamps for installation “on the table”, even additional. The set of brushes to the engine was put. trifle, but nice.

As already noted by reviewers. Quality of execution. Small screws fixing the position of the saw and with an uncomfortable profile. fingers slide away when trying to tighten it. And you need to twist it more tightly: the design is flimsy, the engine is heavy and without reliable fixation in any way. The sole of an incomprehensible alloy turned out to be bent, and apparently from the fact that the box stood for a long time in the warehouse (Lee from shaking during transportation). Yes, yes, apparently the ill.fated engine bent even it. A bar that fixes a protective casing in a stationary position dangles like a fallen woman. The wire is tough, at a minus temperature, most likely it will “stray” finally.

Surprisingly, with all the shortcomings, the saw was excellent, primarily because of her dope. It was originally bought for installation in a sawing table, therefore the flimsy and curve of the sole did not have much importance. Only the same heavy engine had to be additionally fixed, because it manages to lead the disk with its weight: 90 ° does not work. The cut of the cut decreased to 55mm. t.e. The fifth board blooms with a bang. Not later than today inadvertently cut two 45 nails. I learned about this by light ringing. This toothy did not even choke. The dollar and the like economic horrors make you look towards not very “branded brands”. Five thousand with a penny. For that kind of money comparable in the TTX, I drank practically no longer, alas.

Hand disk saw Smolensk instrument Diold DP 1.85. 200. review

Good day, dear friends and guests of pages, needlewomen, joiners and carpenters, red.runs and home craftsmen. No need to explain that the Indian cake can be torn with your nail, but with the help of tools this business will turn out much faster. When processing wood, namely, when cutting it, the necessary tool is a saw. And it is doubly more pleasant if you can stick it into a socket, for example, such a sample as this disk saw “Diold”.

Supply voltage 220 volts, power consumed 1.8 kW, (a decent indicator of gluttony). First, consider the pluses first. A massive metal structure with the possibility of fixing (inverted) on the bed as a circular stationary saw.

A solid departure of the disk above the working surface allows you to saw boards with a thickness of 50 mm. Of the useful “bauls”, the device allows you to change the slope and, accordingly, the angle of cutting.

The graduation is indicated in degrees, it is convenient and understandable to any master. Fixation of the angle on a bolt connection, reliable and simply. Installed disk with a diameter of 200 mm. Sold in any household store. Cooling of the engine is forced, during operation it does not overheat.

The pluses end on this and the disadvantages begin. First, short power cord. The second minus is the most important, very large weight of this whole design, as much as 6.5 kg. You can’t work for a long time, your hands will fall off. There is another not very significant, but minus. There is no smooth start. That is, when you press the Start button, this weighty colossus twitches sharply and is gaining momentum. If a person is not Ilya Muromets, it is likely that the tool will break out and there is a unique chance to be left without fingers or other parts of the body, so you need to keep the saw very tightly.

Noise in work is a normal phenomenon. Engine power is enough with a margin. I have never had, so that the disk stopped, even saws oak boards. I recommend it for use, but for weight I will reduce the assessment.

Hand disk saw Smolensk instrument Diold DP 1.85. 200. reviews

Circular from the Smolensk instrument bought 5 years ago. The parameters can be viewed at

Good day, dear friends and guests of pages, needlewomen, joiners and carpenters, red.runs and home craftsmen. No need to explain that the Indian cake can be torn with your nail, but with the help of tools this business will turn out much faster.

Hello I want to share my opinion and impression from this acquisition. I purchased the DIOLD DP-1,5-190 disco saw when we did overhaul of the floor in my private house and, in its cost, it not only justifies itself, but you can save your money.

My husband bought this thing yesterday to cut the wood-based stove. In the store they turned it on once, she faded. I came home, began to saw the wood-brown stove. After the first leak, I drank and jammed and jammed. The husband went to the store with the same legs with a request to replace low.quality goods.

After cleaning the land from previously growing on it, we sent all the round to the local sawmill We wanted to save, “our own” building materials to get to the point.

Greetings, skillful hands! The fact is that my husband is with the Internet and computer equipment on “you”. Generation of the last century. And I want to leave a review for a new saw. Therefore, under his sensitive control, almost under dictation, I leave this review. Trust!

Disk saw Interskol DP-2101900EM. made in the fraternal Chinese People’s Republic under the proud Russian name “Interskol” (maybe someone knows how to decipher? I have associations only with some international chips on a tree). I showed myself perfectly! No kidding.

In connection with the endless construction of a private house, which has already lasted three years, my husband acquired a disk manual saw, and was very pleased with the acquisition.

I decided to buy a Rotorizer saw, having seen enough how cleverly and beautifully they work on the TV-SHOPA “Shop on the couch”. I bought it, however, not there, but in a special shop in neighboring Estonia. There for this rotorizer, are about twenty.lowering prices.