How To Mow With A Line Trimmer

Preparation for work

If this is your first time mowing a lawn, take a few minutes to figure out how to properly mow with a line trimmer. Walk along the lawn and remove any stones, sticks, or large debris.

Turn on the trimmer and hold it so that the handle fits snugly against your thigh. Make sure the head is at a comfortable height for cutting grass. Walk to one edge of the lot and start cutting the grass.

As you are trying to make an even cut, keep your head parallel to the ground and sweep briefly. It is better to first set the cutting height higher so that it is possible to correct it in an ideal state.

How to properly cut grass with a line trimmer: tips and tricks

How To Mow With A Line Trimmer

Practical garden tools are becoming more and more popular. With the acquisition of a new assistant, inevitable questions about how to properly mow the grass with a trimmer with a fishing line. To begin with, it is a great addition to your existing lawn mower. She can be entrusted with large areas, and the finishing work will be done by a trimmer with a fishing line. To clarify, the line is designed for cutting weeds and delicate branches. For rougher work, models equipped with metal blades or a chain are used.

Safety Tips

Before You Begin It is a good idea to make sure you have protective equipment. For the most part, it is safe to operate a grass trimmer, but there is always the possibility that the machine will start throwing out debris. At the very least, wear protective goggles and protective clothing. Long trousers and thick gloves are perfect. Before starting work It will not be superfluous to inspect the trimmer to make sure it is in good working order.

Cutting technique

It seems like cutting the grass evenly should be simple. run the trimmer over the grass and the line will cut it to the desired length. But this is NOT the best approach and will actually cause Plesha to appear on the lawn. It is important to rely on knowledge to convert a Naughty tool into a reliable machine.

  • The ends of the string are where the maximum cutting force is concentrated. over, the faster and freer the movements are, the easier the process will go. Tapering. It gives the lawn a beautiful look, the technique works especially effectively along the side of the road, near a fence or trees. Hold the instrument so that the string hits the grass at a slight angle.
  • Framing. Where the surfaces are almost parallel, say between a walkway and a roadway, you want to emphasize the edge. Therefore, we turn the trimmer so that the string is vertical. Then drag the tool along the cut path.
  • You don’t have to try all the techniques at once. If the lawn has never had a rod, then first you need to free it of debris, then trim the grass to one length, and only then take the edges.
  • Oblique trimmer. If you have to work in tall grass, then you can use this simple technique. This means that the tool must move along the path of the letter U.
  • Screed. Another technique that is used to remove grass growing on paths in cracks. Tilt the tool so that the tip of the strings just glides over the road surface, then work into the base of the weeds, cutting them down to a hard surface. But be careful: tilting the tool too much and you will just break the line. Accept an angle that is too sharp and the line will NOT cut the grass evenly.

Direction of rotation

Considering further how to properly mow with a trimmer with a fishing line, you should pay attention to specific techniques that will help you achieve the perfect result. often than not, people make the mistake of not paying attention to the direction of rotation. Just like a circular saw throws away sawdust, the trimmer throws away debris. If it rotates counterclockwise, it ejects the waste material from the left side and cuts from the right side.

Therefore, if you are driving on a walkway or along a curb, keep to the right and position the tool head so that it can cut and push the grass to the left. If you go the opposite way, the debris will begin to block the way trim tabs.

Types of line trimmers

There are a lot of them today, so everyone can make a choice based on their own needs. Cordless line trimmers are designed for people who want to work regardless of the power source, they are the most popular. Examples include:

  • Champion TB400 is a cordless trimmer. It has a telescopic bar, compact size and light weight, only 2.8 kilograms. A limiting bracket is provided to prevent damage to useful plants;
  • Gardena PowerCut Li-40/30. A professional tool that can handle even a wet lawn. Additional attention should be paid to the possibility of adjusting the head to work at an angle in hard-to-reach places.

Gasoline trimmers are more expensive, they need regular refueling, but this pays off due to the high power and the possibility of long-term operation on the site without being tied to a power source:

  • Partner B305 CBS. Despite its light weight, it has impressive power. Allows you to tidy up green spaces, rather than having a harmful effect on them by minimizing emissions. A special grass blade and a Tap-type trimmer head are used as cutting tools Go running in semi-automatic mode.

Most modern trimmers can be fitted with an optional line head. There are four types of spin trimming heads:

  • Automatic heads automatically feed the filament when the throttle reaches a certain speed;
  • Semi-automatic heads advance the string when you push the spindle head to the ground when the throttle is engaged;
  • Hand heads require you to turn off the trimmer before pulling or unwinding the rope to advance it;
  • Fixed line heads DO NOT provide string advance. Instead, you use pre-trimmed timelines to replace.

Caring for the trimmer after finishing work

Once you are done trimming the grass, you will need to tidy up the trimmer. The first step may be cleaning along the lawn. To do this, use a broom or broom. Collect all debris and cut grass. If the area is very large, it is better to use a leaf blower. This will make the job much easier.

After that, you will need to tidy up the trimmer. Remove any grass that may have built up in the casing, wipe all cutting parts with a soft cloth. The battery trimmer is placed on charging, the gasoline trimmer is additionally refueled. Storage is carried out in a dry room.

Direction of rotation

Considering further how to properly mow with a trimmer with a fishing line, you should pay attention to specific techniques that will help you achieve the perfect result. often than not, people make the mistake of not paying attention to the direction of rotation. Just like a circular saw throws away sawdust, the trimmer throws away debris. If it rotates counterclockwise, it ejects the waste material from the left side and cuts from the right side.

Therefore, if you are driving on a walkway or along a curb, keep to the right and position the tool head so that it can cut and push the grass to the left. If you go the opposite way, the debris will begin to block the way trim tabs.

Types of line trimmers

There are a lot of them today, so everyone can make a choice based on their own needs. Cordless line trimmers are designed for people who want to work regardless of the power source, they are the most popular. Examples include:

  • Champion TB400 is a cordless trimmer. It has a telescopic bar, compact size and light weight, only 2.8 kilograms. A limiting bracket is provided to prevent damage to useful plants;
  • Gardena PowerCut Li-40/30. A professional tool that can handle even a wet lawn. Additional attention should be paid to the possibility of adjusting the head to work at an angle in hard-to-reach places.

Gasoline trimmers are more expensive, they need regular refueling, but this pays off due to the high power and the possibility of long-term operation on the site without being tied to a power source:

  • Partner B305 CBS. Despite its light weight, it has impressive power. Allows you to tidy up green spaces, rather than having a harmful effect on them by minimizing emissions. A special grass blade and a Tap-type trimmer head are used as cutting tools Go running in semi-automatic mode.

Most modern trimmers can be fitted with an optional line head. There are four types of spin trimming heads:

  • Automatic heads automatically feed the filament when the throttle reaches a certain speed;
  • Semi-automatic heads advance the string when you push the spindle head to the ground when the throttle is engaged;
  • Hand heads require you to turn off the trimmer before pulling or unwinding the rope to advance it;
  • Fixed line heads DO NOT provide string advance. Instead, you use pre-trimmed timelines to replace.

How to properly cut grass with a line trimmer: tips and tricks

Practical garden tools are becoming more and more popular. With the acquisition of a new assistant, inevitable questions about how to properly mow the grass with a trimmer with a fishing line. To begin with, it is a great addition to your existing lawn mower. She can be entrusted with large areas, and the finishing work will be done by a trimmer with a fishing line. To clarify, the line is designed for cutting weeds and delicate branches. For rougher work, models equipped with metal blades or a chain are used.

Preparation for work

If this is your first time mowing a lawn, take a few minutes to figure out how to properly mow with a line trimmer. Walk along the lawn and remove any stones, sticks, or large debris.

Turn on the trimmer and hold it so that the handle fits snugly against your thigh. Make sure the head is at a comfortable height for cutting grass. Walk to one edge of the lot and start cutting the grass.

READ  Which Fishing Line To Choose For Bosch Trimmer

As you are trying to make an even cut, keep your head parallel to the ground and sweep briefly. It is better to first set the cutting height higher so that it is possible to correct it in an ideal state.

Cutting technique

It seems like cutting the grass evenly should be simple. run the trimmer over the grass and the line will cut it to the desired length. But this is NOT the best approach and will actually cause Plesha to appear on the lawn. It is important to rely on knowledge to convert a Naughty tool into a reliable machine.

  • The ends of the string are where the maximum cutting force is concentrated. over, the faster and freer the movements are, the easier the process will go. Tapering. It gives the lawn a beautiful look, the technique works especially effectively along the side of the road, near a fence or trees. Hold the instrument so that the string hits the grass at a slight angle.
  • Framing. Where the surfaces are almost parallel, say between a walkway and a roadway, you want to emphasize the edge. Therefore, we turn the trimmer so that the string is vertical. Then drag the tool along the cut path.
  • You don’t have to try all the techniques at once. If the lawn has never had a rod, then first you need to free it of debris, then trim the grass to one length, and only then take the edges.
  • Oblique trimmer. If you have to work in tall grass, then you can use this simple technique. This means that the tool must move along the path of the letter U.
  • Screed. Another technique that is used to remove grass growing on paths in cracks. Tilt the tool so that the tip of the strings just glides over the road surface, then work into the base of the weeds, cutting them down to a hard surface. But be careful: tilting the tool too much and you will just break the line. Accept an angle that is too sharp and the line will NOT cut the grass evenly.

Safety Tips

Before You Begin It is a good idea to make sure you have protective equipment. For the most part, it is safe to operate a grass trimmer, but there is always the possibility that the machine will start throwing out debris. At the very least, wear protective goggles and protective clothing. Long trousers and thick gloves are perfect. Before starting work It will not be superfluous to inspect the trimmer to make sure it is in good working order.

Caring for the trimmer after finishing work

Once you are done trimming the grass, you will need to tidy up the trimmer. The first step may be cleaning along the lawn. To do this, use a broom or broom. Collect all debris and cut grass. If the area is very large, it is better to use a leaf blower. This will make the job much easier.

After that, you will need to tidy up the trimmer. Remove any grass that may have built up in the casing, wipe all cutting parts with a soft cloth. The battery trimmer is placed on charging, the gasoline trimmer is additionally refueled. Storage is carried out in a dry room.

How to properly cut grass with a line trimmer

Any owner of a country house or suburban area knows that in summer and spring time it is necessary to constantly care for the lawn, otherwise it will lose its external, attractive appearance. Therefore, many dacha owners are wondering how to properly mow the grass with a trimmer with a fishing line. And before you start learning how to mow, you need to choose the right tool for the site and only then use it correctly on the lawn.

  • Trimmer control, as it may seem to many, is not an easy task, but there is nothing special (there is nothing complicated in it) if you properly follow the safety measures and know how to operate it correctly, rather than a garden tool, the cutter of which is a metal disc.

Articles:

We carry out the correct mowing in both cases

The device should move correctly in front of you and strictly from right to left, because the grass you mowed will surely fall onto an already mown area, which will give you the opportunity to mow the tops of the grass initially. Then you Carrying out the reverse movement, through which you will remove all the remaining shoots of grass.

  • When working with large areas of the lawn, it is best to divide the work into several stages, visually dividing the territory into squares. In the process of squinting the grass, you should move along the outside, which will make it possible to once again not trample the grass while doing this, and not complicating the squinting procedure for yourself. To make it easier to work, it is best to move from below, walking parallel to the already treated area, and then return back.

With this approach, you can easily use the line trimmer to mow the grass around the trees planted on the site, carefully bypassing them and at the same time, and not loading the devices. If you mow the grass in the way we recommend above, then you can reduce the likelihood of the grass scattering to the sides, ensuring faster and easier processing for yourself.

How to cut tall grass with a line trimmer

It is advisable to cut tall grass in your garden area with a powerful trimmer, using thick fishing line. But many will most likely agree that the land in most cases where Burian is located will certainly be uneven, as a result of which various garbage and all kinds of stones appear in the owners of such garden plots. To prevent your expensive device (trimmer) from breaking down the mow of tall grass, it is best and faster to mow in two passes. THOSE. First, we cut the entire top of the grass, revealing more difficult areas of the mow and pass the mower a second time.

When you are going to prepare the grass (using a trimmer) for hay, and you are more or less versed in the area of ​​your plot, then you can predict the course of the grass sideways in advance. this will be faster, more convenient and easier for you. The main thing in such a situation Do not rush to mow, but competently with a “cool head” approach the matter.

A few tips for cutting tall grass:

  • Try NOT to overload the mechanism in the process.
  • If tall grass is entangled in the line, the same Disconnect the mechanism so that the motor does not burn out.
  • If your trimmer runs on gasoline, cutting wet grass is strictly prohibited.

How to mow with a line trimmer

Mowing with a line mower is much safer than a trimmer equipped with a cord, but this is not always optimal and profitable. The cutting main element (mechanism) must be selected Based on the garden area and the height of the weeds.

  • Earlier we looked at how to mow with a lawn mower with a line in automatic or semi-automatic mode and manual. In automatic mode, the main cutting element (line) is thrown out after each start of the device motor. On the one hand, it is very convenient, but on the other, it is not very economical, for example, your garden plot is of a non-standard shape. there are uneven corners, notches, and with each next transition from place to place, you need to turn off the device and then turn it on again. It is best in this case to use the second, semi-automatic option. This is when the line is fed into the trimmers by pressing a special button located at the very bottom of the drum (in the cutting area). You just need to press the tip to the ground and the line will be thrown out.

If you are an operator, you must understand that the length of the ends of the cutting element (chain) that is located on the drum in an extended (working) condition should not exceed 15 cm.It is this length that should be enough for an average power of grass trimmers.

What needs to be done to correctly, easily and quickly mow the grass with a trimmer with a fishing line in order for the device to serve you much longer than usual.

  • Try to keep the main drum (coil) from the ground below 5 cm.
  • When mowing taller grass, mow the top first, and only then get close to the stem to protect your device from damage and prevent the mower from breaking.
  • In the process of mowing grass, it is imperative to introduce the cutting element (trimmer) in which the coil is rotating.
  • The lawn grass, which is located near the walls of the garden plot as a decoration, is best mowed, using only the edges of the fishing line, so as not to overload the engine and not wear it out too much.
  • Every 15-20 minutes worked, let the device “rest”.

Prepare the trimmer for work

Depending on what kind of trimmer you have, you still need to prepare it before starting work. If the trimmer is electric, we need to charge it, or plug it into the 220 Volt network and start working like that. If you are using the grass trimmer with petrol fuel, fill the tank. Depending on the design Prepare and check the cutting element. It is NOT superfluous to check the safety of the trimmer. When working with the device, it must be hung on the body and held correctly by the handles. Use protective goggles or a special mesh (protective) helmet when squinting.

Correct mowing of young grass

To ensure that the device works with maximum efficiency and lasts several times longer than the warranty period, mow the grass correctly, observing the following recommendations.

  • Do not lower the coil (drum) of the device under the very roots of the weeds. the distance to the ground is at least 5 cm.
  • When mowing taller grass, cut the top first. Cutting grass close to the root without removing the top of the stems will entangle the line, stop the drum and force it to shut down.
  • Do not mow the grass against the drum.
  • Mow down ornamental grass near walls or fences and do not push the trimmer drum too far. This will save the motor from overload.
  • After every 15 minutes of trimmer operation, allow the engine to cool down. at least 20 minutes is required.

But petrol trimmers have a large time reserve. 50 minutes for work and 20 minutes for a break.

Features of the trimmer with line and cord

A trimmer is a more delicate machine than a full-fledged electric or lawn mower. A trimmer that does not work with a line, but with a line is an even more delicate device. Cord. essentially wire. can damage the bottom of the trunk in young trees, passing into the root, which is NOT the case with line. With thick stems of weeds. for example, weeds that have begun tillering. the line may NOT have time to cut all the weeds.

READ  How to Charge a Fishing Line Into a Trimmer Coil

Despite the obvious convenience, on uneven and irregular areas, mowing grass in one place and moving to another, you restart the motor. Exit. transition to semi-automatic control: the trimmer in the working part has a separate button that is easily pressed when the drum head touches the ground. The line will immediately be thrown out of the cut.

The length of the line must NOT be more than 15 cm in working order. Longer line will get tangled, smaller line. Will not mow effectively. The optimal line diameter is 2-3 mm.

Preparing the trimmer for work

Fill the tank with gasoline (or diesel), not overfilling it. Two-stroke trim motors require mixing gasoline with engine oil (not car oil) in a ratio of 1: 32-1: 50. You need to know which oil in what proportion is mixed with gasoline for your model. In four-stroke trimmers, you will need to pour oil and gasoline into different tanks. again, according to the instructions.

Grasp the handle of the device as directed in the instructions. Some trimmers Equipped with a bicycle handlebar-like double handle. Now follow these steps:

  • Close the air damper;
  • Switch on the ignition circuit using the key or button;
  • If there is a booster mini-pump on the carburetor. pump some fuel into the engine by making 3-5 clicks on the “rocker” lever;
  • Pull the starting cord until there is significant resistance to its movement;
  • Cut the cord up to 5 times.

The engine will start. When mowing grass, use protective goggles or a helmet with a mesh to prevent the grass from spreading towards the face.

How to properly cut grass with a line trimmer?

Mowing your lawn is the main way to keep your lawn area tidy. If you don’t want to mow with an ordinary scythe by hand, the modern owner acquires a mechanical scythe or a trimmer. If the choice fell on a trimmer, the question arises, how to carefully mow the grass so as not to damage trees and shrubs (if any).

Preparing the trimmer

If it is raining or has just finished, you may receive an electric shock when cutting wet grass. Before using for the first time Make sure you have assembled the device correctly. some models are shipped disassembled. Precise assembly will protect you from injury, and the unit itself from failures and sudden breakdowns. Trimmer assembly instructions are described in the user manual.

When using the trimmer, charge the battery (if the device is designed for autonomous operation). Lubricate the mechanical gearbox with lithology or grease. If there is a battery in the circuit of the device. Connect the plug to the socket and start working.

Mowing tall grass with line introduction

For thick stems of grass (Burian) use a more powerful trimmer with thick line. However, in areas where large weeds grow, the soil is often uneven. If it gets caught on clods of earth, the trimmer motor will brake abruptly. By overusing this, you can easily damage your engine. Mowed the upper tier, you will see where the grass reaches its greatest length. in deeper places. Focusing on such “height differences”, you will equalize the “mowing” of the lawn, brought its view closer to the ideal.

The cut grass is suitable for both hay and lawn feeding. At the same time, the course of mowing the grass is easier to plan, and the process will go faster.

Tips for mowing tall grass are as follows.

  • The engine must NOT be overloaded.
  • If the line becomes tangled on uneven ground or tall grass, immediately turn off the engine.
  • When using gasoline or diesel as an energy carrier, it is impossible to mow wet grass.
  • You need to move the trimmer straight in front of you and to the left, because the cut grass falls on the previously treated sector. Thus, the upper layer of the grass stand is cut off. The layers below it are mowed when you have already gone in the opposite direction.
  • If the cultivated area is very large. mow one conditional zone after another, into which you divided the area before work.
  • Move exactly on the outside so as not to trample the cut grass, making your result inconspicuous.
  • Mowing lines must be parallel to each other. This will allow you to easily bypass the trees found on the site, while overloading the motor is excluded.

Subject to these recommendations, the grass will not scatter to the sides during work, and the process itself will be simplified and accelerated at times.

For information on how to properly mow grass with a trimmer, see below.

Under hay

Use a disc as a cutting element because meadow vegetation is tougher than usual. It is better than fishing line specifically for hay in that it cuts through dry grass better. This way, the grass will not get stuck on the line, which could result in poor engine performance. Hay does not need to be cut small, it should be quite tall, so try to cut the hay at the root.

Smooth lawn

To create a level lawn surface, try to work your greenery as low as possible with your garden equipment. So all the grass will be the same height, which will make the coverage even and beautiful. Don’t forget to tilt. For best results, tilt the device at least 30 degrees towards the grass surface. This will cut the grass as low as possible. Any other irregularities can be removed with garden shears, if any.

General terms of use

The general rules of use should definitely be reminded to those who are thinking for the first time about how to remove grass with a trimmer and do not yet know how to use it. It is these foundations that will help you start cleaning your site with high quality.

Among summer residents, there is a tendency to use trimmers more and more often, because, unlike lawn mowers, they allow you to remove grass in hard-to-reach places, and professional models can even help you process tree branches. Another advantage of the trimmer is the ability to work at height and dusty branches, which can also greatly help in cleaning on your territory.

Another important point is safety. Since lawn mowers have a high rotation speed (they reach several thousand revolutions per minute), even a small stone can fly out at high speed and cause harm to a working person.

Check and inspect all trimmer parts before starting work. Ensure trimmer operation. Since they are electric and gasoline, you will need to organize their work depending on the type of equipment. Electric should be plugged into the power supply and charged if it is not charged, and gasoline should be refueled, if required.

When starting up for the first time, let the trimmer run in. If you bought a new device, then you need to let it run for a few minutes without load in order for the motor, knives, fishing lines, and rotating elements to start. This can be called a kind of warming up for equipment, in addition, it can help prevent some troubles before direct work, because the assembly and quality of garden equipment are different.

Running in an electric trnimmer includes several stages.

  • To get started, start and work with the trimmer for a short time, literally 5 minutes.
  • Then you can increase the running time up to 10 minutes, but it is necessary to watch the motor so that it does not overheat.
  • After several trials, the electric trimmer can be used on a permanent basis. Do not forget about the engine cooling system, which is available as an additional function on some models.

If you do not know which type of mowing is best to start with, then it is better to try cutting a low lawn with fishing line. This will allow the engine to run smoothly. No need to immediately load it with a large amount of work.

Mowing tall grass

This requires special attention. Tall grass needs more careful processing than simple grass. The fact is that there is an effect of winding the vegetation onto a coil. In this case, the grass remains on it and prevents the mechanism from rotating at full power. This significantly slows down the process and reduces the number of revolutions.

To prevent this from happening, go through the path in several stages. Gradually cut a certain amount down the height, going down and down the stem.

It should also be borne in mind that if your technique is working recently, then mowing tall grass can be even more difficult. Therefore, DO NOT run for long periods of time to avoid overloading the motor. It will be enough 15-20 minutes with a break of 15 minutes. Since it is better to cut the grass in several stages, do not forget about the grass catcher. It will start to clog very quickly and this will lead to problems with the instrument. Clean thoroughly so that the next cleaning does not take too long.

How to properly cut grass with a trimmer?

In the midst of the summer season, people who have their own plots have a problem. It lies in the fact that after winter and spring, grass and other vegetation grows very quickly in THESE areas. Today we will consider options for mowing grass. For example, it is better to disassemble ordinary trimmers, since they provide a person with more scope for action due to direct movement with this technique, and they are very inexpensive.

How to put on and hold correctly?

The quality of your work also depends on what technique you use. For proper technique, you must be able to hold the unit, and for convenience, put it on correctly. The point is that not all trimmers are equipped with a shoulder strap. If you have one, then you need to put it on so that you feel comfortable. There are models of devices, the belt of which can be uncomfortable, so try to put on the trimmer as conveniently as possible.

Another function is to adjust this belt. On higher quality models, its convenience was assigned a special role and special positions were made, which will allow the scythe manager to NOT experience inconvenience. You can adjust the belt in height, choosing the one you need.

Now let’s talk about how to properly hold the unit. Different types of trimmers have different handles. For some, it is made in the form of a bicycle handlebar (which ensures the distribution of the load on both hands). On some units, you can see the handle in the shape of the letter D. The bicycle version must be held with both hands, and firmly.

Despite the rubberized grips, it’s best to rely on yourself and NOT rely on them NOT to slip. Hold the D-shaped grip with one hand and palm to provide a wider grip. This will give you complete control of the stick, which will have a positive impact on handling.

READ  Trimmer Petrol Patriot Bad Gains Speed

Mowing rules

In order to mow the lawn efficiently and quickly, you need to follow the technique and know some features that will save you time and effort. You can work faster, now we’ll tell you how.

Divide your site into zones. This will help you understand how much you need to complete. Also, you will not have the misconceptions about whether you have already worked here and whether you have passed the second time. For the first time in the seasons, the lawn is mowed at a level of 4-5 cm, gradually decreasing to 3-4. Mowing rates We set ourselves. You can keep more, less. It all depends only on you.

If the motor is located underneath, the likelihood of moisture ingress will be even higher. It is also not recommended to work with the trimmer in the rain all for the same reasons. The ingress of water can cause a short circuit, which in the future may develop into a malfunction of the unit. Therefore, it is better to wait for more favorable weather for work.

It is recommended to work clockwise. It is this direction that will leave the grass cut by you on the outside of the entire mowed area. Hold the coil NOT lower than 5 centimeters during operation. This is a safe mowing option, which is well suited for those who have recently started using such equipment. When it comes to working in a fence or other places where you only need to mow a small part, then use the edge of the line. This will help ensure that the engine will not overload and wear out.

Recommendations

Before using the technique, it will be advisable for you to read the instructions from the manufacturer itself and familiarize yourself with the general functions and structure of the trimmer. Functions To be located on the control stick. Understanding the building blocks and components is helpful in the sense that you know how you can and should handle it. Select the load for the motor, work for the cutting elements. all this will be useful to you during operation.

Pay attention to the following points.

  • First of all, it is technique. She has failures and breakdowns. Before work, carefully check all the components of your technique, because mowing the lawn with such tools is an important matter. You need to check the filters (clean if necessary), the fuel level, cutting elements (in case of a malfunction, it is better to take the knives to the master), the engine and other parts. This can be done after work, but some manufacturers recommend it.
  • Some trimmers have engine cooling and vibration damping systems, but they are NOT everywhere. Therefore, watch out for the heating of the motor during operation, because its overheating can lead to problems. Occasionally draw your attention to bolts and other items. Although the extinguishing system can work, but on some representatives of garden assistants, the paper clips are still gradually unwound, in total it will lead to breakage.
  • Sometimes it also happens that the turnover falls. In this case, first check all filters, and then try to work. Testing technique is much better for direct action.
  • If parts are broken, it is better to contact a technical center. DO NOT try to repair the equipment yourself, as this can only accelerate the breakdown. Mechanics have a complete understanding of this technique, you better trust them.

How to work with the trimmer correctly, see below.

Correct mowing

You need to move from right to left in front of you, so that the cut grass will fall on the previously treated area, which will allow you to first cut off the tops. Then a reverse movement is made, which removes the remains of vegetation.

When working with large lawns, it is best to divide them into squares. During the mowing process, it is necessary to move along their outer side, which will allow NOT to trample the grass again and cover the entire area. To facilitate the task, it is better to move from below, Walking parallel to the section, and then come back.

At the same time, the use of fishing line allows cutting the lawn around the trees, bypassing them around the trunk.

If he mows the grass in this way, then this will reduce its spread to the sides, ensuring the correct processing of the territory.

Line selection

First of all, you need to install a fishing line that will act as a cutting tool. Choosing too thick is not worth it, as it will seriously overload the equipment and this will NOT lead to anything good. It is better to opt for a NOT too thin option. it will cut soft-stemmed grass well and give opportunities to increase speed.

How to mow with a line trimmer?

Almost any owner of a summer cottage or suburban area knows that it is necessary to regularly care for the lawn, otherwise it will lose its attractive appearance and overgrow with grass. To do this, you must choose the right trimmer and use it correctly.

Choosing a cutting tool

The choice of lawn mowers for mowing grass in the country is NOT limited only by the selection of the engine. An important role is played by the cutting tool, with which all lawn mowers are equipped. Its appearance usually depends on the power level of the engine. Tools with low power, as a rule, are equipped with a cord (line), and more powerful ones. with a cutter disc and metal knives.

The trimmer line has different thicknesses (1.2-4 mm) and shapes:

  • Round;
  • Square;
  • To speak with rounded;
  • Round;
  • Square;
  • Polygonal.

The thickness of the line is determined based on the specific characteristics of the braid. Puts too thick line on the tool for which it is NOT designed, not recommended. bushings can quickly wear out.

For mowing tall grass on the site, it makes sense to equip a trimmer with knives instead of a fishing line so that the grass does not wrap around the spindle during mowing with a fishing line. Knives are metal and plastic.

It is recommended to remove green shrub growth with metal knives, and hard plants, dead wood. with plastic ones. The knives must not be used on rocky areas, as it is prohibited to do so according to the safety rules for using the tool. Also, gasoline trimmers are equipped with a different number of knives, the more there are, the better the scythe works. If you are planning to purchase a hay making machine, a device with more than two knives will not work, # 8212; they will cut the grass too finely.

How to put on the trimmer belt priority

Trimmer Engine Features

Engine # 8212; it is the heart of the design. The duration and quality of work, which directly depends on him. Often, trimmer motors are equipped with a single-cylinder two-stroke engine with a power of 0.5-3.3 kW. As a rule, it is filled with a mixture of oil and ordinary AI-92 gasoline. It is impossible to take another fuel, so as not to cause overheating and subsequent damage to the engine.

Two-stroke engines are capricious to maintain, therefore, when choosing a petrol trimmer, inexperienced users are advised to use a tool with a four-stroke engine. You don’t need a mixture for it, because oil and gasoline are poured into it in different compartments. In addition, these engines are more powerful and able to mow even thick bushes.

In any case, when choosing a tool, it is worth deciding what kind of vegetation they will have to remove. Since if you are purchasing a lawn trimmer, you can safely stop at two-stroke engines, as they are lighter and cheaper.

The location of the gasoline engine on the trim tab can be top or bottom:

  • From the bottom, the motor is placed on electric or battery trimmers. This design is more balanced and vibrates less. But such a trimmer should not be used on wet grass;
  • From above, the motor is placed on electric and gasoline trimmers. Knives and a thicker line will do. There will be no problems with wet grass.

Investigating the device of a gasoline trimmer, and choosing the right model, you will probably want to opt for motors from European manufacturers and avoid Chinese ones, but this is unlikely to succeed. Unfortunately, many European manufacturers buy engines from the Chinese, since the cost of assembling them in China is much lower, so in 90% of cases just such an engine will come across. But despite this, they are all of good quality and have a long warranty period.

The most famous companies that produce engines:

Of these, only HONDA is not made in China.

Types of restraining belts

  • The most inexpensive # 8212; these are petrol engine trimmers equipped with a 1 shoulder strap, but with them the load on the body is unevenly distributed.
  • organic option # 8212; this is a model with double materials, soft backpacks are included with it, but a hip pad protects the vibrations.
  • The most expensive # 8212; This is a knapsack suspension. Their cutter can be perfectly tailored to individual physiological characteristics.

Choosing a gas-powered scythe, stop in several models, turn it on, hold it in your hands and only then decide which one will be more convenient to work with.

for petrol trimmers from leading manufacturers range from 3,300 rubles to 35,000 rubles. The cost depends on the power of the engine, its volume, structure weight and processing width.

Preparation for work

Depending on the type of trimmer, you need to hold it correctly, otherwise mowing the grass will be a very difficult and inconvenient process:

  • Upper motor solutions. they are put on the shoulder using a special loop and are held on it;
  • Knapsack options. worn over the shoulders and quite often are the most comfortable, especially with a large lawn;
  • Lower propulsion devices. held by hands by special handles.

After the trimmer has been put on, it is necessary to Position the trimmer parallel to the grass.

Features of external elements of lawn mowers

Bar # 8212; the main conductor that unites the motor and the cutting system into a single structure. In its cavity there is a shaft, which is flexible or straight. The bar can be disassembled, due to which it is much more convenient to store it. The shaft design also determines its shape. A straight shaft is more reliable for the rod. True, if the landscape of your site differs in height in different places, it is better to purchase a trimmer with a curved shaft.