How to refuel the head of a trimmer for Echo grass. How much do the heads for trimmers for grass find out their real cost

Learning to correctly wrap the fishing line for a trimmer to the coil of a trimmer for grass and lawn mowing instructions for installation

Owners of private houses know how necessary the type of tool is such as a trimmer for grass. It can be gasoline and electric, and they differ in the design of power units. For injection of grass in areas where there are stones, trees and other obstructing objects, a fishing line for a trimmer is used as a cutting device. This consumable in the process of use wears out, so how to wind the coil of a trimmer for grass, we will consider in detail in the material.

Fishing lines is called consumable, which consists of nylon, and serves as a cutting device. Through this equipment, the grass grows, which is ensured due to rotation of the instrument head with a high frequency. This material has a different thickness, which depends on its use on the corresponding tools of low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers for grass with motorcycles (from 2.4 up to 3.2 mm).

The more powerful the tool, the accordingly there should be a cutting equipment. This affects not only the quality of the injection of grass, but also on the life of the material. If you ask the question of how to wind the coil of a trimmer for grass, then it’s time to change the reload of the tool. With the onset of spring, this issue is becoming more and more in demand, so it’s time to understand the step.by.step instructions for replacing the fishing line in the coil of the trimmer for grass.

How to remove a coil from a trimmer for grass and extract a fishing line for a trimmer

Initially, before filling the fishing line for the trimmer to the coil of the trimmer for the grass, it is necessary to extract it from there. Coil or tip is a device that is located inside the braid, bobbin or drum. The heads are of different types (depending on the manufacturers), however, the principle of replacing the fishing line on the coil has the same. First of all, we will figure out how to remove the head from the tool, as well as how to get a drum with a fishing line from it.

It is interesting! The replacement of equipment can be done directly on the tool, but if you do it for the first time, it is still recommended to remove the head, and study the detailed process of winding. After the technology is mastered, you can perform work on replacement on a trimmer of a motorcycle or a gas station.

Instructions on how to promote a hand head on a trimmer, has the following look:

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how replacement is performed. When dismantling, consider the following nuances:

• It is recommended to remove the head periodically to prevent the corrosion of the threaded connection. If you never unscrew the screw, then if necessary to do it will be difficult and even sometimes impossible
• If the screw has a tetrahedral boring of the head, then for twisting you should select a screwdriver or bit of a suitable size to eliminate the licking of the faces on the head
• When assembling the installation, a threaded seat should be treated with lubricants, for example, solidol or machine oil
• If the edges on the screw are licked, then for its unscruptions you can use special clamping forceps
• There are drums that do not require preliminary disassembly. To dismantle them, you should take up it, and rotate in the opposite direction of the direction of the clockwise

Knowing how to disassemble the drum, you should continue to clarify the process of replacing a trimmer fishing line for grass. Below the video shows a detailed process how to open a trimmer coil for grass and disassemble it.

Device

The basis of this device is a ratchet formed by a case and a spool. In many respects, the design is identical to a semi.automatic model, the difference in the form of a spool, a fishing line for a trimmer to which they wound without pulling it out of the case.

The spool is made of plastic and contains 2 compartments for the fishing line, from below it is propagated by a spring that determines the force in which the ratchet mechanism is triggered, and the clamping plate and the wear.resistant cover are triggered on top.

There is a through hole inside the spray, through which the fishing line for the trimmer is threaded, after which it wrap it with the help of the lid. This design provides maximum comfort when working with the head.

How to wind a fishing line for a trimmer?

To wind the cord, do the following:

• Place a trimmer for the grass so that it is convenient to work with the head;
• Combine the strip on the cover with marks on the lower (removable) part of the case;
• cut the required amount of cutting string;
• Insert the fishing line for the trimmer into the opening of the case and remove it from the other side;
• stretch the cord so that 2 identical pieces from different sides of the trimmer head turn out;
• rotating the lid, wrap the entire fishing line for the trimmer, the direction of rotation is indicated on the lower part of the case.

Remember, twist the cover of automatic coils for trimmers with a straight and curved bar in different directions, so focus on the arrow.

Manual or mechanical coils their purpose and application

The first trimmers for grass were produced with manual types of coils that have a primitive design. They consist of a plastic or metal disk in which there are holes for fixing the fishing line. The holes have the corresponding size, which allows the cord (fishing line for a trimmer) of a certain diameter. However, this is not the only drawback of equipment, since another minus is the need for frequent fishing line refueling. Below is a variant of the simplest coil with a fishing line for a trimmer for grass.

Following the simplest coils, mechanical head heads appeared, inside which a bob is installed with a fishing rod. Such devices are excluded deficiency of the fast consumption of the cord, however, to serve a new fishing line, you should interrupt the work on the injection of grass. To supply the cord, the head is equipped with a manual regulator, through which the fishing line stretches. Today, the manual type models are rarely used, which is associated with their great drawback. the need to interrupt the work and drown out the engine in order to lengthen the cord.

Semi.automatic coils and how effective they are

The most popular among mowers are trimmers for semi.automatic grass. From the name it is clear that the fishing line for a trimmer exits the coil in a semi.automatic mode. For this, the head is equipped with a mechanism through which the fishing line is submitted. Kosarya for supplying the cord must be touched by the lower part of the earth’s head in order to bring the mechanism into effect. This is very convenient, since it is not required to jam the tool motor and stop the grass of the grass.

Lengthening of the cord is carried out due to centrifugal forces. Working with a tool with a head semiautomatic device is very easy and convenient. Many masters recommend using this particular option, but do not indicate the following information:

• If you plan to use semi.automatic coils, then exclusively branded models
• Buying cheap devices is irrational, as they do not serve even several months
• Rationally buy a semi.automatic type, which are designed directly for a specific brand and a model of a trimmer for grass, since universal are often distinguished by low assembly quality

Based on the foregoing, it should be noted that it is far from always rational to buy coils for trimmers of a semi.automatic type, especially if there are models more perfect and no less reliable. automatic.

Fishing winding

Tramoring the fishing line in a trimmer coil for grass is a relatively simple procedure, provided that you adhere to a certain algorithm of action. When you need to determine how many meters of consumables are enough, wind it on the bobbin so that the skein does not exceed the diameter of the sides. Having decided on the length of the cord, follow the following instructions:

• Fold the consumable material so that one end of the fishing line is 10-15 cm longer than the other.
• You need to start charging with the central side, which divides the backpack of the trimmer for the grass into 2 parts. Find a groove where the cord should be inserted. The latter is bent twice.
• Determine in which direction you need to wind the fishing line for the trimmer. To do this, take a look at the bobbin on which there can be an arrow or inscription. She indicates the side of winding. If there are no designations on the coil, then look at the arrow on the mowing head. carry out windings in the opposite direction.
• Wash the consumable material carefully, a round to the round. Try to adhere to maximum thread tension.
• After completing the cord laying, fasten first the short end of the material. To do this, insert it into the groove on the side of the coil, which is suitable in diameter. The second end (more authentic), attach to the groove on the other side of the backpack of the trimmer for the grass.
• By fixing the fishing line for the trimmer, cut its ends. Do not forget to leave allowances about 10 cm.
• Install the refitted coil to the mowing head of the device. To do this, you need to insert and pull the thread alternately into the weekend of the head, then place the keyboard of the device in the skin.
• By applying the required force, pull the cord from the fixing grooves and tighten the material. At the end of this action, put on the lid and fix it using the latches.

Step.by.step winding of fishing line on the reel

You can wound a cord for a trimmer for grass in another way, in which two segments of the material are charged instead of one. The replacement is carried out like this:

• Bend one end of the cord thread in the form of a hook.
• At the bottom of the bobbin there should be a hole that is designed to fix the fishing line. Insert the bent over the end of the thread there.
• Wind the cord material in the direction of the arrow to the desired level, which does not exceed the diameter of the coil of the trimmer for the grass.
• The same actions need to be done for the second cell of the bobbin.
• Assembly of the device head is similar to the first way.

Trimmer for grass is the necessary and useful tool for a summer cottage and a private house. Many own and actively use it, but not everyone knows how to replace a fishing line for a trimmer in a trimmer, especially at first.

In this instruction, we will analyze the entire replacement process step by step. Looking ahead, there are two ways to refill a fishing rod with a fishing rod. There is no fundamental difference. the difference is that in the first case, one fishing line for a trimmer will be refueling, folded in half, and in the second there will be two segments of these forests.

Features of the use of trimmers

A trimmer for grass, mowing grass with a fishing line, can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flower beds, a row in a garden plot.

Such a convenient, and most importantly, effective device, like a trimmer for grass, exists in several variations:

As the names understands, the types of trimmer for grass are noticeably different from one another. But regardless of the type of this tool, its cutting element can be a fishing line for a trimmer. Of course, a trimmer tilted for the grass for a trimmer is not infinite. And sooner or later it will need to be replaced by a new.

Fishing consumption directly depends on the frequency of using the device and the scale of the work performed. The more herbs are brazen and the more often it is trimmed with a trimmer for grass, the more actively a fishing line for a trimmer is consumed in it. And, accordingly, the faster it will end. In this regard, the question arises: how to refuel a fishing line for a trimmer to a trimmer coil for grass?

Not everyone knows the answer to this question. But the winding of the fishing line on the coil plays an important role in the work of a trimmer for the grass. To make the device normally, it is very important to correctly wind a new fishing line for a trimmer to the reel. About how to change a fishing line for a trimmer on a trimmer, and will be discussed in this article.

Which line for a trimmer to choose

Before you stock up on this material for refueling in a trimmer for grass, you need to decide on the choice. After all, the usual so.called round fishing line for a trimmer is far from the only existing look. How to choose the most suitable? First you need to determine the working conditions.

Type choice. a line for a trimmer with a round section is the most common. It will suit any reels with the rarest exceptions. This type of consumable is suitable in order to mow fresh, juicy grass. But with the mowing of the so.called dryness, this kind may not cope anymore. It is pointless to mention attempts to mow shrubs and mention.

In addition to the usual type, there are others with sharp faces. Usually they are made by a “star” or “square”. The presence of sharp faces is the main feature and key difference between these threads.

It is thanks to this feature, the threads of such species are able to mow dry weeds. But the spicy threads are not devoid of disadvantages, the main of which can be called rapid wear and strength, markedly inferior to the round type.

In addition to the already mentioned types of forests, there are still interesting and often encountered varieties. Especially among them can be noted fishing lines, inside which a metal wire is stretched. Threads of this type are often used in tools working on gasoline and having an engine more powerful than one and a half horsepower.

Threads with a metal core come both with a round section and with sharp faces. Regardless of the type of cross section, such threads are the best suited to overcome hard.to.stop plants. Threads related to this type easily mow not only dry grass, but even small shrubs.

The threads with wire inside are favorably different from other types of consumables for their incredible wear resistance. But unfortunately, this feature has a more than noticeable effect on the price of this type. The cost of threads with a core significantly exceeds the cost of threads of other types.

Choice in thickness

In addition, special attention should be paid to the thickness of the consumption material. For mowing young grass, a thread is suitable with a diameter of one and a half millimeters. The larger the diameter of the thread, the more dry and rude weeds it can overpower.

When choosing a fishing line in thickness, there is one “but”. It is important not only to evaluate the capabilities of the material, but also to take into account the features of the trimmer for the grass. You must definitely look into the user’s management, which is attached to the tool, and find information about the requirements for the cutting element.

The use of inappropriate thread can lead to the failure of the tool. The use of too thick thread will entail the overload of the device engine. And the use of too thin thread will significantly increase the wear of the torque.

That is why it is necessary to approach the choice of consumables no less responsibly than to refuel in a trimmer for grass. When a suitable fishing line for a trimmer is found and purchased, you can begin to consider the ways to wind it on the coil.

Types of coils: how to charge each of them?

There are 4 types of coils, for each of which their own methodology for winding the cord is used:

Below we consider how the fishing line for a trimmer is inserted and put on for each of them and how to wrap it.

Mechanical collapsible

These trimmer heads consist of two or three parts connected by thread. to the upper part are screwed either the lower or fixing the screw holding the lower part.

• unscrew the lower part of the trimmer head or twist the fixing screw, use the key supplied with the coil;
• Remove the remains of the old fishing line;
• Cut pieces of the necessary length;
• Place the segments on the upper part, then cover them with the bottom and fix them using a standard key.

Mechanical non.devastated

There are 2 varieties of these heads:

We describe how to refuel and wind a fishing line for a trimmer into indiscriminate coils of both types and how to fix the cord on them.

The advantage of the coils of the first type is that they are leaning to spend a fishing line for a trimmer, because after the protruding fragments are eager or tore off, it is enough to rewind a little cord and pass it out through the corresponding holes.

With coils where there is no such cavity, the situation is different, the string is held in them due to the bend between the input and output hole.

That is, the total length of the fishing line consists of the length of the protruding fragments and the site passing through the coil and is 7-10 cm.

To charge the coil with a cavity, do this:

• If you have already used such a head, then cut a piece of fishing line of the required length, if not, wrap the cord to fill the cavity, moving both ends towards each other, then cut the cord, leaving pieces a little more on the outside;
• Draw a fishing line for a trimmer through the opposite holes;
• Cut the pieces of string to the required length protruding outward.

To charge a coil without a cavity, consider that a minimum of vibrations will be only with four protruding “tails”, which means two fishing line segments.

Cut 2 pieces of cord to length, necessary taking into account the method of their attachment, then act in one of two ways:

• Insert each segment into the hole, draw past the location of the nut and remove through the corresponding hole;
• Bend the string segment in half, then insert simultaneously into both holes from the inside of the coil.

How to properly tie a fishing rod (bobbin) of the lawn mower without disassembly, shown in the photo above.

Semi.automatic

The order of action, how to refuel a fishing line for a trimmer in a semi.automatic coil:

• Squeeze the clamps on the side surface of the case with your fingers (it is often written on them “push”);
• Carefully remove the lid;
• Pull the spool propagating its spring and washers;
• Remove the remnants of the old string from the spray;
• Cut a piece of fishing line of the required length;
• Fold the cord in half, forming a small loop on one edge;
• Insert this loop into the slot of the partition dividing the spool into two sections;
• wrap both halves of the strings, each in your section, the direction of winding depends on the type of trimmer for the grass, but always corresponds to the direction in which the coil is wound and the opposite of the rotation of the coil is rotated, if you do not know which way it is spinning, focus on the arrow. drawn on a rogue or lid;
• when 10–20 cm cord remains outside, draw it through the slots of the corresponding size in the spool designed to fix the fishing line during the charging of the coil;
• draw the edges of the fishing line each through their hole in the coil body;
• Install the spring, rogue and washers in the case;
• Pulling the spool with your finger, pull the pieces of the cord sticking out of the case to straighten it inside the coil and remove it from the slots;
• put on and snap the lid;
• Strongly pressing the button with your finger, pull out a little fishing line again to completely straighten it inside the case;
• Cut the protruding “tails” to the required length.

The photo above shows how to put a fishing line for a trimmer in a slot.

Automatic

Winding and an integral refueling of fishing line in this type of coils occur as follows:

• If there are lines of the fishing line on the rogue, then either soak it by turning the button against the arrow drawn on the lid, and pulling the cord, or remove the lid, as described above, pull out all the parts of the mechanism outward and remove the fishing line for a manually, then collect everything as It was;
• Combine the tags on the button and the lid, then make sure that the holes in the body coincided with the canal inside the spool;
• Cut a piece of fishing line of the required length (usually 3-4 m);
• Insert the string and stretch it so that 2 pieces of the same length are obtained;
• Turning the button towards the arrow on the lid, wrap the entire cord on the spool, leaving pieces of the length required for mowing;
• If necessary, cut the sticking fragments to the desired length.

Another scheme of proper winding and refueling of the fishing line on the reel (head) of an electric trimmer for the grass is described in the video below:

How to properly wind a fishing line for a trimmer on a spool of any trimmer for grass, including electric:

How to properly charge a fishing line for a trimmer into the head of a cutting tool and how to refuel it into a trimmer for grass, including in a trimmer ethletric for grass (electric ships):

Sometimes you need to install a new coil instead of a failed, and the next video on how to correctly install the head on one of the models of electric trimmers for the grass:

With visual examples, it becomes more clear how to properly put a fishing line for a trimmer to the coil of an electric trimmer for the grass before putting it in a mower and start the device.

How to remove and disassemble a coil

Before proceeding to the process of replacing the cord, users of trimmers need to remove and disassemble the coil. Consider how to do it.

The mowing head of a trimmer for grass consists of several parts: a casing, springs (not in all models), bobbins with a cord and cover.

Attention! Before proceeding with any actions to maintain an electric unit, it must be disconnected from the network.

Trimmers most often use 2 options for fastening a mowing head.

Option

To remove the head of the trimmer for the grass, it will require its complete disassembly.

• To remove the lid covering the inside of the head, it is necessary to press on the latch (latches) located on its two sides.
• Removing the lid, you will see the spool that must be removed from the body. In some coils, a spring is installed under the bobbin, which must be carefully pulled out so as not to lose it in the grass.
• Removing the bobbin, in the center of the case you will see a screw with a slot under a cross.shaped or flat screwdriver. It is possible that there may be a bolt under the hexagon or nozzle “Asterisk”.
• Using a screwdriver, choosing the necessary bat (nozzle), you need to unscrew the bolt (counterclockwise).
• After extracting the fasteners, take up the part of the part and, shaking it in different directions, remove the gearbox from the shaft.

Option

In this version, the head is twisted onto the gear shaft. To remove it, you need to fix this shaft. To do this, in such trimmers, for example, in the Huter and Champion devices, a hole is provided through which you can insert either a thin screwdriver or a metal rod.

So, to remove the bobbin, take 2 simple steps.

• Insert the screwdriver into the hole and stall the shaft.
• Take the head of the head and start twist it clockwise. It should be twisted in this direction for the reason that the thread cut on the shaft is left.

Field winding algorithm

Depending on which model of the trimmer for grass is used, the type, thickness and length of the fishing line is selected. The diameter of the cord can be from 1.2 to 4 mm. It is not difficult to guess that the thicker you will refuel the cord, the more rigid and thick grass it is able to cut off.

In most cases, a universal fishing line for a trimmer with a diameter of 2 mm is used.

In order to find out which line diameter can be used on your mower, there are 3 ways.

• View information about the thickness of the cord in the instructions for the apparatus.
• Look at the squash itself. It can be given information about possible fishing line diameters.
• Insert a fishing line for a trimmer into the output. If it passes into it without difficulty, then the cord of such a diameter can be used.

The fishing line for a trimmer is wound on a coil in a mowing head. Therefore, first it needs to be opened (this was mentioned above). There are 2 methods of winding the cord.

The first way

To correctly determine how many meters of the fishing line are required for a specific coil, it is necessary to wind it on the bobbin so that the skein does not exceed the diameter of the sides. If the fishing line for the trimmer will look out beyond the edges of the coil, you cannot insert it into the casing. After you have decided on the length of the material, it must be tucked in a bastard, so do the following.

• It is necessary to fold the fishing line for double so that one end is 10-15 cm longer from the other.
• Please note that the bobbin is divided into 2 parts by the central side, from which charging begins. Find a groove on it and insert a cord into it, bent twice, putting a slight effort.
• It is very important to determine in which direction the fishing line for a trimmer is wound on the reel. If you look closely, you can find an arrow on the bobbin or an inscription with an arrow indicating which direction the winding should be carried out. There are times when there is no arrow on the coil. In such a situation, you can look at the arrow drawn on a mowing head, and wind the cord in the opposite direction.
• Winding should be carried out carefully, a turn to the turn, with maximum thread tension.
• After laying the cord is completed, you will need to fix it first the short end of the fishing line, inserting it into the groove suitable in diameter on the side of the coil.
• The second end, the one that is more authentic, is attached into the groove on the opposite side of the squash.
• After fixing the fishing line, cut its ends, leaving the allowances about 10 cm.
• Next, it is necessary to install a refueling coil in a mowing head. To do this, alternately inserting and pulling the thread into the weekends of the head, place the bobbin in the casing, after which, by applying the required force, pull the fishing line for a trimmer from the fixing grooves and tighten it.
• Now you can put on the lid and fix it with the help of latches.

The second method

Some coils provide a second method of fixing the cord: you can charge 2 sections of the thread, instead of one folded in half. Fishing line replacement occurs according to the following algorithm.

• Before changing or charging a new thread to the coil, determine how many meters it will be required by the way discussed above.
• Bend one end of the cord in the form of a hook.
• Find a hole intended for fixing the fishing line at the bottom of the bobbin, and insert the end of the thread bent by a loop into it.
• Wrapping the cord is required according to the direction of the arrow to the required level not exceeding the diameter of the coil.
• Do the same actions for the second cell of the bobbin.
• The assembly of the head is no different from the method that was given when the refueling of the bobbin was considered folded by half a piece of fishing line.

There is a very simple and quick way to replace the fishing line for motor.cuts without disassembling the mowing head, which you can see this video.

The ends of the cord sticking out of the holes in the casing can be cut to the required length, already when the part is installed in the trimmer. You can do this in two ways:

• By turning on the trimmer for the grass (when rotating, the ends of the fishing line will part on the knife, fixed for these purposes on the protective casing);
• Cutting the extra ends with scissors so that they do not touch the casing body.

The second method is used if I had to put a large diameter cord, and a trimmed knife cannot shorten it.

If the thread was charged into a mowing head, but the length of the protruding ends of the cord is insufficient, then before starting the device they must be lengthened. this applies to the head with manual adjustment. However, there are cases when using a semi-automatic mowing head, when, due to the insufficient length of the protruding ends of the cord, they do not automatically lengthen. In this case, it is necessary to turn off the unit (on the electric device you need to pull the fork out of the outlet), manually press the button located at the bottom of the part, and stretch a little fishing line. After this procedure, the cord will be able to advance again thanks to centrifugal strength, if you put the maximum spindle speed.

No matter how thick the fishing line for the trimmer you should remember: in order not to constantly interrupt the work and do not change the cord, you should avoid areas where a working tool can touch hard surfaces (stones, borders, thick dry branches, etc.D.).

The main malfunctions of the coil

Users of the electrimmer and lawn mower often face a problem associated with a semi.automatic braid head. Coil malfunctions can be as follows:

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. there was a snack, t.e. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, with even turns with good tension.

Option 2. too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

Option 3. a fishing line for a trimmer was soldered inside a mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a fishing line on solid items.

• In the first case, the cord of third.party manufacturers can be made of low.quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
• But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can) or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
• Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

The cord spontaneously lengthens

There are situations when a user of a trimmer for grass notices a very fast fishing line consumption. At the same time, he never hit the ground with a button to lengthen the fishing line. The reason that the fishing line for a trimmer spontaneously lengthens, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, forget to install a clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

Also, a fishing line for a trimmer can lengthen without using a button if the spring is weakened. If the spring check confirmed this fact, then it is necessary to put several goals under it to strengthen its clamping properties.

How to remove the coil and replace the fishing line for the trimmer

The owners of the trimmers, mainly beginners, confuse, bordering on panic, when it becomes necessary to change the cutting tool or fishing line for a trimmer in a reel. Very often, when trying to unscrew the mowing head, users simply make it unusable, not suspecting that it is unscrewed in the opposite direction. So that this does not happen, if you need to replace the tool, it is recommended to familiarize yourself with the step.by.step instructions given below.

• Before refueling the fishing line for the trimmer to the coil, drown out the engine of motorcycles or de.energize the ethletric trimmer for the grass to avoid injuries that may occur in case of accidental rotation of the cutting tool.
• Unscrew the nozzle mounted on the gearbox shaft. To do this, the shaft must be fixed by combining holes on the puck and on the axis, and inserting a metal rod or screwdriver into them.
• Unscrew the nozzle. You should know that the thread on the shaft is left. Therefore, to twist the coil of the trimmer for the grass should be right, that is, clockwise.
• Disassemble the mowing head. Most often, the head cover is attached to the fixers. To remove it, you need to drown these latches into the case, pressing the edges of the lid. If your trimmer has a semi.automatic mowing head, which has a button from below, then disassembling the nozzle should be done carefully, since you can lose a spring that sometimes flies away when removing the cover.
• Cut the required amount of fishing line. Usually its length is 5 meters. Use the cord of the diameter that is indicated in the instructions for the tool. It is not recommended to exceed the maximum diameter of the fishing line, since this will lead to increased load on the engine and greater consumption of gasoline.
• Find the middle of the segment of the cord, folding it in half. You will get a loop.
• Special grooves are cut out inside the coil (there may be holes). Insert the loop from the fishing line into this groove.
• Wind a fishing line for a trimmer to a coil, turning it counterclockwise. You need to refuel the cord as evenly as possible, the turns should be laid without ceiling and with good tension. When the winding is finished, leave the free ends of the fishing line about 20 cm long and fix them in the grooves located on the sides of the coil.
• Collect the braid head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if it is available). Install the coil in the case, and prone the ends of the cord through the holes or eye.
• Dress the lid and fix it with latches.
• Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Tighten the coil of the trimmer for the grass will need to go to the left (against h. Arrows).

How to wind a fishing line for a trimmer to a trimmer coil for Echo grass

When refueling the fishing line for the first time, a myth process can be thought quite labor.costs, alas, alas, over time and dexterity, the problem is solved significantly more freak.

To refuel a fishing line for a trimmer, you need:

• Take a coil, unscrew its lid. On some coils, a thread on the left is done, so the lid must be unscrewed in the right direction.
• Measure 5 meters of fishing line;
• Fold this segment in half, in other words, find where the middle is;
• Then put this middle of the fishing line in a special hole on the coil;
• Wind a fishing line for a trimmer to the side, where the arrow shows;
• If there are two places for winding, then the first part of the fishing line should be wound for one half of the coil, and the second part should be on the other half;
• Stick both ends of the fishing line in the holes of the coil;
• Twist the lid.

There are several types for a trimmer:

• Stronger. round;
• For mowing soft vegetation. curly;
• For noting narrow grass. with notches;
• Special. approaches certain types of trimmer for grass.

The type of cross section of the cutting thread should correspond to the vegetation that needs to be mowed.

If you need to replace the fishing line for the trimmer, then you need to select specifically the type that is recommended by the manufacturer specifically this model of the trimmer for the grass, in other words, the thickness of the cutting thread should be suitable for the power of the motor and the size of the unit.

It is better to choose a specialized cutting thread. It is worth soaking a fishing line for a trimmer for several days if you plan to replace it in a coil.

How to wind a fishing line for a trimmer to a trimmer coil for grass?

After soaking, it acquires an elastic look and becomes stronger.

Cutting thread and possibly made of various components. Often found in the middle of them. nylon.

The myth of the material is characterized by the highest degree of wear resistance, the ability to withstand different temperatures and the highest loads.

You can store fishing line for a nylon trimmer for more than one year, it does not dry out does not lose its strong.

Therefore, its service life and possibly quite long.

Coils in another head for motorcycles have a different structure:

• One.built. In the modification of such a trimmer for the grass there is only one working fishing line for a trimmer. Such an unit is used mainly for small work, such as ending the grass.
• Two.string. Will be both automatic and automatic. Here the equipment includes two strings. Such a trimmer is used for herbs for mowing and clearing sites.

Annotation on the proper wound of cutting thread on the coil of a trimmer for the grass:

• First you need to disassemble the head. For this purpose, you need to press on the latch and turn the lid to the side. Next is extracted by a spool.
• Measure the required image the amount of cutting thread and stick it into a slot.
• From 2 sides, wind a fishing line for a trimmer in the direction of the arrow.
• The ends of 15 cm long should be thrown out of not wound.
• These ends are inserted into the reverse slots.
• Then the ends are fixed in the hole on the head.
• Then the spool is carefully inserted into the case, for this purpose you need to press a little on its surface.
• If necessary, of course remove the remaining ends of the thread outward. For this purpose, it is necessary to pull one end of the thread at first, and then the other so that they can simply pass through the slots on the head.
• Now you should assemble the grooves on the case and tighten the lid.
• After that, press on the spool and test it in full. If a click was heard, the slopes snapped up.
• Next, it is necessary to stretch the free ends of the thread to the end.

To change as it is also called to wrap the cutting thread to the coil, it needs to be removed.

The complexity of its removal is depending on the model of the tool:

• Low motor tool. The motor here is almost by the ground. To remove the coil, it is necessary to press on the buttons located on the side of the trimmer for the grass. After pressing these buttons, the case is opened where the coil with a fishing line is placed.
• trimmer for grass with a curved bar. Here you need to turn counterclockwise a special lamb. After that, the coil is removed and the spring there.
• Direct rod. The bar is kept off with the help of a screwdriver as it is also called another object. With rotation clockwise it is removed. Then disassemble the tool to parts and remove the bobbin.
• If a tool with one osik is used, then about 4 meters of thread will come in handy. This thread is passed into the hole of the coil of the coil, where it can be fixed. Further one end of the fishing line is directed along the arrow. Further, the end of this thread is fixed in the groove, which is in the bobin. This was necessary for the purpose of the thread did not have the strength to unwind when assembling the coil. In the absence of grooves, you should hold a fishing line for a trimmer with your hand and collect a bobbin.
• If a tool with 2 antennae is used, then at first it is necessary to check the number of available grooves.

If the coil is armed with an automatic mechanism, then they wrap a fishing line for a trimmer in this way:

• The thread is threaded into the hole that is located;
• Fix the ends of the thread in grooves on the case.
• The coil is collected and pressed by a special button;
• After that, the fishing line for the trimmer itself begins to dangle in the right side.

#29 How to wind a fishing line for a trimmer to a trimmer coil for grass or motorcycle

It is always necessary to keep in mind that the cutting thread must be protected from hard things. This will extend its service life.

If you do not adhere to this rule, you will often have to stop the work, remove the coil and change the thread to the latest.

With two.stringed automatic heads:

How to refuel a fishing line for a trimmer to a trimmer for Echo grass

How to change a fishing line for a trimmer in a trimmer and which is better to choose

Since the choice of a trimmer for the grass we saw in the previous article, now we will tell how to correctly refuel a trimmer for the grass with a fishing line, and which is better to choose based on the criterion of work.

After you purchased a trimmer for the grass and began to use it intensively, at some point the question will arise about the substitution of the fishing line, since this is the most weary element in the tool, the rich operation of the trimmer for the grass will often lead to substitution of consumables.

What types of forests I am

The frequent type of fishing line, which is actually suitable for all types of coils. a round cross.sectional cord. Turning the fishing line into the coil of the trimmer for grass 2 Part How to season the fishing line for the trimmer to winding the fishing line on the reel.

In the market of garden equipment, there is a small one, how to refuel a fishing line for a trimmer trimmer for NIKEA1750 grass.

This is a regular fishing line for a trimmer suitable for mowing of juicy grass, but it will be much more difficult to mowed with dry, and even more so it cannot cope with the shrub.

As a rule, the diameter that can mow young grass does not exceed 1.6 mm. The thicker the thread, the more rough grass it is able to overcome.

There are fishing lines with sharp faces in the form of a sprocket or square, this option is more adapted to mowing dry grass just due to the existing sharp faces, but its lack of wear is more wear and it is inferior in strength to the round cord.

There are fishing lines with improved aerodynamics with characteristic dentes, scales and notches, a similar product makes less noise, but they use it only on benzos, since the output of such a thread from the coil is difficult, it is most often used with discs in which segments are inserted. The disadvantage of such a product is its fragility.

Most often in gasoline trimmers with an engine of more than 1.5 liters.With. Apply cords with a metal cable inside. This thread is ideal for mowing dry grass and small shrubs.

The presence of a core, positively affects the wear resistance of this material. The disadvantage of such a cord is its price, which is significantly larger than the above opponents.

How to wind a fishing line for a trimmer to a mowing head motorcycles or a trimmer for grass / Fishing line replacement on a motorcycle

How to wind a fishing line for a trimmer to a coil of motorcycles or a trimmer for grass. Replacement of fishing line on a motorcycle. How to wind a fishing line for a trimmer for a trimmer for use for use price in grass using fishing line. Features of fishing line

Replacement and preparation of fishing line on a benzotrimmer. ECHO GT-22GES BASTRIMMER. How to replace a fishing line for a trimmer in a braid, coil of the Husqvarna 128r trimmer for Husqvarna grass. Preparation and winding of fishing line

The video shows in detail how to wind a fishing line for a trimmer to a trimmer coil for grass or motorcycle. Watch how to refuel a fishing line for a trimmer trimmer for grass video! How to refuel a fishing line for a trimmer to a trimmer coil for grass. The gas line is dressed

How to refuel a fishing line for a trimmer to a trimmer coil for grass

In order to wind a fishing line for a trimmer, it will take about 10-15 minutes. How to wind a fishing line for a trimmer to a trimmer coil for grass? Help to refuel a fishing line for a trimmer trimmer for grass. What is the coil of a trimmer for grass? Plastic case with a cassette inside, on which there is a special hook for convenient winding of fishing line.

How to refuel a fishing line for a trimmer trimmer for grass photo. Almost all the coils of the trimmers have a similar attachment principle, this is a central screw-button, when pressed, it becomes possible to stretch the fishing line for the trimmer of the required length. The photo below shows several examples of various coils for trimmers.

Bobbins of the trimmers, the motor of which is located near the ground, have a different fastening to the rotation axis, they have two buttons on the coil located on the sides that need to be squeezed, the rest of the thread is no different from the other cassettes.

The principle of proper winding of the fishing line is similar in all of the above cases, so for example, consider the standard option with two antennae.

To remove the coil with a fishing line, you must unscrew the screw in the center, but keep in mind, the thread there is left, so you will have to twist clockwise, it is specially so that it does not open under the influence of centrifugal force during operation.

Next, using the screwdriver, disassemble the head and remove the coil, on which the fishing line for the trimmer is directly wound. Having measured the required length and folding it in half, you need to tuck a fishing line for a trimmer into a coil, bringing it out, as a result, its ends opposite each other (for this there are special slots for fixation).

After that, it is necessary to assemble the head in the reverse order, passing the ends of the cord in two corresponding holes.

If there are doubts or it is not entirely clear how to charge a fishing line for a trimmer for a trimmer for grass recommend that you see how to correct the fishing line for a trimmer into a lawn mower. In this video, the instructor will open a trimmer head in detail by steps, it will measure the required amount of fishing line, as a rule, this is from two to four meters, and demonstrate the assembly and installation for a trimmer for the grass.