How to remove the spool from an efco grass trimmer

Trimmer coils. types and features

The efficiency and performance of the domestic trimmer for grass on the site largely depends on the quality of the fishing line. It is located in the coil, or as it is also called, trimmer head. Manufacturers produce different types of spools. Each of them is distinguished by its design features and individual principle of action. After having studied them in detail, it will be easier for a gardener to choose the right reel for a specific application.

The device of a household brushcutter begins with its working body, the role of which most often plays the spool for the grass trimmer.

There are 3 types of heads on the market, which differ from each other by the method of feeding the cutting line:

• automatic spools. in nozzles of this type, the cord is fed when the revolutions of the working engine of the brushcutter are increased. The operator himself takes no part in lengthening the line. it occurs in fully automatic mode. Automatic line extension heads are the most convenient to use and are most often used by gardeners who tend large areas. Among the disadvantages of these attachments, experienced users highlight the frequent breakdowns of the device and the highest cost among all types of trimmer spools;
• semi-automatic heads. nozzles of this type work on a fairly simple principle: for the filing of the cutting line, the spool has to move against the ground surface. When you simultaneously press a special button, the built-in anchor mechanism is actuated. as a result, centrifugal forces arise, under the action of which the line for the trimmer is extended and the operator can continue to work on the site. These attachments require a certain amount of skill from the operator to operate;
• manual coils. in the design of these heads, the cutting cord is extended mechanically. Accordingly, to feed the line, the operator must turn off the brushcutter engine and pull out the trimmer line by hand. Despite the inconvenience in operation, it is this type of spool that is recognized as the most reliable and popular among gardeners.

In addition to the above types of mowing heads, there are also universal cutter heads on the market. They can be installed on any model of the domestic grass trimmer, regardless of its factory configuration and purpose. Universal head stands out for its high reliability and does not require frequent repairs.

Types of heads according to how the line is threaded

In addition to the difference in feed algorithm, trimmer reels are divided among themselves by the method of threading the cutting line.

There are such types of heads on the market:

• “fast”. these coils do not require removal from the grass trimmer. To tuck the cutting cord into the head, the operator needs to pull its end into a special hole in the side of the nozzle, and several times wrap the line for the trimmer around the central axis of the head. At the end, the opposite end of the cord will need to be cut and continue mowing grass;
• collapsible. in order to tuck in the line for the trimmer, the user needs to remove the spool from the grass trimmer and disassemble it. After that you need to rewind the cutting filament, reassemble the attachment and put it back on the brushcutter.

It is not uncommon to find semi-auto reels on the market that are factory designed with a housing, a pair of built-in parts, and a bobbin. The built-in parts are equipped with springs, and the bobbins themselves can be single-section or double-section. In single-section bobbins, the trimmer line is wound evenly on each side. In the two-sectional, each of the ends of the cutting cord is wound on the corresponding side. This type of nozzle is considered the most practical and convenient to use, as the cutting line for the trimmer inside them never gets tangled.

The design of the single-section bobbin involves the possibility of its own revision. To convert it into a two-section, the user will need a solid metal plate on which to measure the diameter of the existing bobbin and cut the workpiece on the drawn contour. To get the thickness, you need to make measurements of the place on which the cutting cord is wound. In doing so, make sure that nothing interferes with the rotation of the circle. After that, it is necessary to make a small notch and put it on the bobbin. To fix the ring it is better to choose “Moment” glue or a special adhesive tape. The result is a homemade two-section head for the grass trimmer. which can be mounted on different models of brushcutter.

Main faults of the reel

Users of electric trimmers and lawnmowers often encounter problems with semi-automatic mowing heads. The problem with the spool may be as follows:

the line for the trimmer does not extend automatically

If the grass trimmer line does not extend when the grass trimmer spool button lightly strikes the ground, the reasons may be as follows.

Option 1. jamming has occurred, t.е. cord jammed between coils. This problem usually occurs if the user has wound the trimmer line on the spool unevenly, with overlapping coils, or has wound it with insufficient tension. In the latter case, when the mowing head rotates at high speeds, the cord begins to tighten under the influence of centrifugal force, resulting in a possible inter-twist of the fishing line. To fix the problem you will have to disassemble the spool on the trimmer and rewind the cord correctly, that is, with even turns with good tension.

Option 2. The ends are too short and protrude from the head. the trimmer line may not come out when hitting the ground, if its ends sticking out of the head are not long enough (short). In this case, the centrifugal force is not enough to cause the trimmer line to extend. Therefore, it is required to stop the machine (turn off the engine or unplug the electric grass trimmer) and pull the line for the trimmer manually, pre-pressing the button.

Variant 3. the trimmer line is soldered inside the mowing head. This causes the spool to freeze and does not turn when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the reel during prolonged operation of the machine, the impact of the line on hard objects.

• In the first case, the third-party cord may be made of low-quality and fusible materials that cannot withstand the mechanical and thermal loading. Therefore, preference should be given to “proprietary” lines.
• But if you bought a line of unknown quality for your trimmer and it often solders while working, you can follow the example of some users who, after filling the cord in the reel, moisten it with either silicone grease (from a spray bottle) or mineral oil. This procedure makes it much less likely that the line will solder to each other.
• A line for a trimmer may also bind if it hits a hard object while mowing (a rock, a fence, a dry branch, etc.).д.). This causes it to stretch a little and retract back into the head at a high rate of speed. The friction heats the cord and causes it to stick together. The only thing you can do to fix this malfunction is to open the grass trimmer reel and rewind the line for the trimmer.

The cords are unintentionally lengthening

There are situations when a grass trimmer user notices very fast line consumption. At the same time, he never hit the button on the ground to extend the line. The reason that a line for a trimmer unintentionally lengthens, being cut on a special knife on the cover of the machine, may be the lack of a spring in the mowing head. Often beginners users of mowers, trying to load line for trimmer in the reel, forget to install the clamping spring in the head, or lose it at all when opening the cover, and later, do not even suspect about its existence.

Also, the line for the trimmer can be extended without using the button, if the spring is loose. If checking the spring confirmed this fact, you need to put some washers under it to strengthen its clamping properties.

How to remove the reel and replace the line for the trimmer

Owners of trimmers, mainly beginners, get confused, bordering on panic, when it becomes necessary to change cutting tools or line for a trimmer in the reel. Very often, when trying to unscrew the mowing head, users simply cause it to fail, not realizing that it unscrews in the opposite direction. To prevent this happening and in case you need to replace the tool, we recommend that you read the step-by-step instructions below.

• Before tucking the line for trimmer into the spool, turn off the brushcutter motor or de-energize the electric grass trimmer to avoid injuries that can occur when accidentally starting the cutting tool rotation.
• Unscrew the bit that is attached to the gearbox shaft. To do this, the shaft must be secured by aligning the holes on the washer and on the axle and inserting a metal rod or screwdriver.
• Unscrew the brushcutter head. Please note that the thread on the shaft is left-handed. That’s why the grass trimmer’s reel should be turned to the right, that is, clockwise.
• Disassemble the mowing head. Most often the head cover is fixed on clamps. To remove it, you will need to push these clips into the body, pushing the edges off the cover. In case your trimmer is equipped with a semi-automatic mowing head with a button at the bottom, disassemble the mowing head carefully, as you can lose the spring, which sometimes flies out when you remove the cover.
• Cut the amount of line needed. It is normally 5 meters long. Use a cord of the same diameter as specified in the instruction manual of the tool. You should not exceed the line’s maximum diameter because it will strain the engine and you will use more gas.
• Locate the center of the cord by folding it in half. You will have a loop.
• There are special grooves (holes may be present) inside the spool. Insert the noose of fishing line into this groove.
• Wind the line for the trimmer onto the spool by turning it counterclockwise. The cord should be threaded as evenly as possible, and the coils should lie down without overlapping and with good tension. When you’re finished winding, leave the free ends of the line about 20 cm long and fix them in the slots on the sides of the spool.
• Reassemble the mowing head. Before you finally assemble the nozzle, don’t forget to insert the spring and the washer (if there is one). Place the spool in the housing, and thread the ends of the cord through the holes or eyelets.
• Put on the cover and secure it with the latches.
• Screw the head back onto the gear shaft, also secured with a screwdriver. Screw grass trimmer reel to the left (counterclockwise). arrow).

How to Change a Trimmer Filament in an Efco Trimmer

How to change the line in any trimmer So, first, unscrew the nozzle. Do this by turning the reel to the right. Here we have the reel with the remains of the old line. We open this. The cover is often closed with latches that can be opened with a screwdriver by inserting it into the holes and applying gentle pressure. Or you need to press the lock and turn the cover in the direction of the arrow. In this case, you need to keep the cover itself, because the reels have an auto-feed spring that can push out all the inner parts of the reel when straightened. Gently pulling out the spool, we remove the scraps of hair from it.

Now you need to take 5 meters of new mowing line and fold in half (to find the middle). In the middle part of the spool there is a recess (in some designs a hole), for which we need to hook our line for the hair growth trimmer. There is also an arrow on the reel that shows the winding direction. An important detail is that if the spool has two compartments, one half of the spool must be wound in one direction and the other half. the other one. After winding, you must leave 15-20 cm of mowing line free. On the top ring of the coil there are also two notches through which these loose ends should pass. We have handled the winding itself directly.

The last step in the mowing line replacement process. reel assembly. First you need to put the springs and washers in their place. Then, holding the spool with one hand, you need to screw the ends of the mowing line into the appropriate holes on the sides of the nozzle with the other. Then set the spool in place by pulling the hair growth trimmer line and taking care not to move the spring. When all the internal elements of the nozzle are in place, you can close the drum with the lid. You just have to work hard to get the snaps in place. Voila! The tapered grass trimmer is ready to go! When choosing a trimmer line for your grass trimmer (gasoline or electric), it is worth highlighting some points, which we will discuss in detail.

The shape of the cutting element. The easiest and cheapest to produce. Is a round line for the trimmer. However, ergonomic and environmental requirements limit its use. because of its physical properties, it produces an unacceptably high level of noise (comparable to the noise of the engine itself). It’s a classic Husqvarna or Oregon RoundLine or Chipmaster. To reduce the amount of noise they produce, they give it a special shape. A spiral, like the Oregon DuoLine Plus (15 dB noise reduction) or with special transverse grooves, the Husqvarna Whisper (-8 dB). Following the laws of physics, the “working” part of the cutting element during mowing is only the end face, not the side face. However, to enhance the “sharp” growth trimmer line, that is, for efficiency, the cross section is changed to a facet: star, square or square with teeth. Oregon Starline, Nylsaw or Flexiblade. For example, according to experts, the Oregon Nilso, because of its square profile, is 27% “cheaper” than its round counterpart, which obviously has an impact on the mowing speed.

# change # any # diameter # shape # grass trimmer # gasoline brush # for # coil # mowing # repair # lawnmower # replacement

What kind of lines are available?

A common type of fishing line that fits virtually all types of reels is the round section cord. How to Reel a Mowing Head. Before you trimmer nozzle. It is a standard line for trimmers, but it is not good for cutting lush grass, and it is much harder for cuttings, much less brush.

Usually, the cross section that can be used to mow young grass does not exceed 1.6 mm. The thicker the thread, the coarser the grass it can overcome.

There are lines with sharpened edges in the form of a star or a square, such a variant is more adapted to mowing dry grass just due to the available sharp edges, but its disadvantage is more wear and tear and in terms of strength it is inferior to the round cord.

There are lines with improved aerodynamics with appropriate dents, scales and notches, similar product makes less noise, but use it only on benzokosa, since the output of such a thread from the spool is difficult, use it in most cases with disks, which are inserted segments. Answer@: how to remove the mowing head from the grass trimmer. The disadvantage of such a product is its fragility.

In most cases, gasoline trimmers with an engine more than 1.5 liters.с. use a cord with an iron rope inside. This article explains how to disassemble the trimmer head and how to trim the grass trimmer. This thread is perfect for mowing dry grass and small shrubs. Install the trimmer head to remove it from the gear rod or from the engine. How. The presence of a core, positively affects the durability of this material. The disadvantage of such cord is its price, which is significantly higher than the above-mentioned opponents.

How to tuck the trimmer line into the grass trimmer reel

To wind the line for a trimmer, you’ll need about 10-15 minutes. What is a trimmer reel for grass? Plastic body with a cassette inside that has a special hook for comfortable line winding. Virtually all trimmer reels have a similar attachment principle, this is the central screw-button, when pressed, it becomes possible to pull the line for the trimmer of the required length. The photo below shows several examples of different spools for trimmers.

Bobbins trimmers, the motor of which is at the ground, have a different attachment to the axis of rotation, they have two buttons on the spool, located at the edges, which should be pressed, otherwise, the change of thread in the same does not differ from other cassettes.

The principle of winding the line correctly is identical in all cases mentioned above, so let’s look at the standard version with 2 antennas as an example.

To remove the coil with a fishing line to unscrew the screw, located in the center, but note the thread is left, so you have to twist clockwise, made this on purpose that while she did not open under the influence of centrifugal force.

Next, using a screwdriver, dismantle the head and pull out the spool, which actually winds the line for the trimmer. Measuring the desired length and folded in half, you must zakazhivaya line trimmer in the coil, bringing ultimately, its ends opposite each other (for this there are special slots for fixing).

After that you need to assemble the head in reverse order, passing the ends of the cord in the two respective holes.

If there are any doubts or it is not quite clear how to charge the line on the trimmer for grass, we advise to look at how to correctly wind the line for a trimmer lawnmower. How to remove the head from the grass trimmer. In this video clip the instructor will carefully step by step uncoil the trimmer head, measure the right amount of line, usually 2 to 4 meters, and demonstrate the assembly and installation on the grass trimmer.

Design Features

It should be noted that the cutting head for grass trimmer contains special arrows. They allow the reels to run in different directions. If there is a need to wind the line for the trimmer in the direction of rotation of the shaft, it rotates to a specific position. Too much wrapped filament can cause a machine breakdown. Two arrows are found only on imported models. Now there are heads with one arrow on the market.

If the filament is not wound after the semiautomatic head has struck, the previous filament was not wound correctly. That is, after the grass trimmer head has been installed, the user has not pulled the ends of the fishing line out of the slot. Another unpleasant thing when mowing grass can be sintered coils.

Why it happens? This happens when the filament meets a hard object. At the same time, it brakes sharply and on subsequent movement, the line for the trimmer begins to go inside the device. By doing so, it gets on the bobbin and sticks together. Because of this, the worker has to take a break and correct the situation. However, this can be avoided. Before you install the spool, it is necessary to treat the line for the trimmer with a special silicone substance.

Various trimmer models use a semi-automatic head consisting of two parts. the body and the bobbin. Both elements contain springs. The second part can be performed in several variants:

• single-section. both parts of the line are wound together;
• two-sectional. each end is wound on a certain part; this type is the most effective, because the line for the trimmer does not get tangled and sintered.

There is a simple and inexpensive way to turn a one-section bobbin into a two-section bobbin. To do this, you will need a solid plate. From it you need to cut a circle, the diameter of which should be equal to the thickness of the bobbin. This takes the thickness near the place where the line for the trimmer is wound. This wheel moves freely. Next, a cut is made on the ring, put on the bobbin and connected with glue or tape.

As a result, it is possible to wind the line for the trimmer on the necessary section. The head for the grass trimmer universal can have from two to four holes, which are opposite each other. The mowing ends come out of them. In addition to the presented reels, there are heads, where a certain size of line is inserted. In this case the number of whiskers increases to twelve. Many users believe that such a device is quite convenient. However, not all people hold this opinion.

They think that more line is needed in this situation. In addition, in order to replace it, it is necessary to stop the work process. Grass trimmer head, the caliber of which can be varied, is suitable for cutting grass, shrubs and trees. Before you buy a grass trimmer, you need to study the terrain, as well as the features of the equipment. So, we found out what is the head for the grass trimmer universal and how to refuel it correctly.

To look after the lawn near the house or cottage can not do without a grass trimmer. As you know, the reels of these tools wear out quickly. However, in this case, much depends on the vegetation with which a person fights. For one-year-old grass, there is very little wear and tear on the reel. But it’s not easy to fight weeds.

How to choose a model?

On the market there are mostly plastic modifications. They are made with steel cores. You should first pay attention to the line diameter. For one-year-old grass and small weeds the size 1,5 mm is suitable. The height of the coil should not exceed 80 mm. The winding system is most often used semi-automatic type. However, there are models that are triggered only by touching the ground. So the trimmer blade wears out much slower. It costs such a modification in the area of 800

The said coil for grass trimmer universal reviews from buyers mostly receive positive. First of all, it should be noted the small weight of the model. The width of the presented modification is 72 mm. Screwing system is provided by the manufacturer of a semi-automatic type.

The line for the trimmer head is selected with a diameter of 1.3 mm. The model copes great with annual grass. As noted by the owners, the wear and tear of the reel is extremely low. Owners may have certain problems with large weeds. Most often it is the cup that breaks. This coil costs around 650

Repair of grass trimmer efco 8061 with your own hands

We will try to answer the question: repair grass trimmer efco 8061 with your own hands on the recommendations of the true master with the most detailed description.

The repair shop performs repair of trimmers Efco as a gasoline and electric. We know and know how to make any model of a well-known Italian brand. Availability of a wide range of spare parts allows us to perform works as soon as possible. All work performed by our specialists and installed components have a warranty of 2 months.

Thanks to great experience and a large material base, we can afford to make free diagnostic work, and eliminate minor malfunctions on the spot without leaving the trimmer for the grass at us. That means we can repair Efco grass trimmer of any modification right in your presence. We also try to make a diagnosis immediately after submitting the equipment for repair.

We accept Efco gasoline and electric grass trimmers of all models for repair: 8060, 8061, 8091, 8092, 8100, 8110, 8130, STARK25, STARK26, STARK37, STARK38, STARK40, STARK42, STARK44, STARK2500, STARK4400, 8200, 8220, 8250, 8260, 8300, 8350, 8355, 8400, 8405, 8420, 8425, 8460, 8465, 8510, 8515, 8530, 8535, 8550, DS2500, DS2600, DSF4200, EF3600. If your model is not on the list, we just did not have time to add it.

I had a problem with the Italian trimmer. Only it’s 8 years old. Three years ago some grass wrapped around it pulled the shaft 30mm out. The plastic coupling between the two bearings failed. Unscrewed the brass bushing fasteners (the design is indestructible) took out the shaft bearings and the remains of the plastic bushing. Cleaned plastic from melted plastic bearings replaced bushing with iron bushing lubricated and reassembled. Mowing, now the vibration has increased, the plastic tube inside the boom is worn off. So soon to the morgue. Thinking of replacing, mostly my wife mows, she does not like the straight boom. So I’ll have to buy the Italian efco 8130 again. But I don’t really like the reel with the clips.

Old major wrote :. but you should be warned that this thing can mow any grass except fibrous. like nettles for example. The fibers run freely between the line holder and the aluminum body and wind up on the hexagonal tube! And to remove the body of the line holder and to get to the shaft. you need to remove the retaining ring, and it is not easy to remove even with a special tool without mats.

Similar problem! Bought it in 2001. Efco 8060 grass trimmer (600 W). Everything would be fine if not for the extremely poor design of the cutting unit. there is a significant gap between the stationary part (metal) and the rotating part (plastic, black). It is a lot bigger in photo than in reality (I did it intentionally. you can see a hexagonal shaft element in the gap). The grass gets in this gap. both the fibrous grass like nettles, and the grass can also get wrapped up. especially when the speed drops sharply, and the grass trimmer has no time to chop the grass. Grass gets wound around the hexagon and gets between the shaft and the housing Consequently, the strongest heating in this place, as a result of which the plastic unit with the fishing line in close proximity to the housing melts (fig. 2. in the melted and then solidified plastic “soldered” grass), eventually the unit jams. Tired of even not so much the need every time to disassemble the entire unit to the end (had to buy special pliers for the locking rings, which are in the node 2), but the possibility of serious damage to the trimmer for grass.

Old major wrote: for on the rotating part. on the bobbin. clearly a rim must be 5-7 millimeters high and outside.

The conclusion. a serious design flaw. Question. who are the options for solving the problem can advise? Possible options:

• Try to find a compatible unit from other Efco trimmer models in the service, which does not have this defect?
• Install on the plastic bobbin at the top of something like a knife to cut the fibrous grass?
• On the whole circumference of the bobbin to attach a skirt? the proposed options are quite controversial. maybe there are some more, tried and tested already, since this problem exists objectively and I’m not the first who raised it?

Old major wrote: To surrender in the shop do not offer. in the first this trimmer for grass for two days mowed all the same that it was required, and his bobbin after 30 meters of fishing line and nettles winding times 10 and the corresponding disassembly does not look very presentable! Yeah, I liked it. By the way, I found my way of treating the problem of winding, but I will not say yet.

And this method really solves the problem?

Trimmer repair is necessary when the device does not turn on or does not function properly. All owners of private houses and suburban areas are familiar with the problem of excessive vegetation, getting rid of which is sometimes difficult. As you know, progress does not stand still and new developments and useful inventions appear in all areas. It also affects agriculture. No more need to cut the grass with the old inconvenient devices, the help came to modern petrol mowers, which can get rid of vegetation in the most inaccessible places.

Trimmer heads Efco, Patriot, Champion, Alpina, Husqvarna, Partner, STIHL, Echo, Makita, Al-Ko, Texas, DDE, Homelite, Honda, Dolmar, Flymo, Oleomac, Ryobi, Solo, Jonsered, MC Culloch, MTD

For models EFCO Stark 25 (with adapter C5147). Fast line loading. High strength plastic. Metal plated trimmer head nut. Nut M101.25 (left-hand thread), head diameter 125 mm, trimmer line 2.0-4.0mm.

For EFCO Stark 25 (with adapter C5147), DS220T, DS240T, DS26004T, DS3200T, DS3800T. Head easily dismantled and easy to service. M101.25 nut (left-hand thread), 123 mm head diameter, 2.4-3 trimmer line.3 mm.

For models EFCO 8060, 8100, 8200, 8250R, STARK26TR. Head made of high-strength plastic. M81.25 nut (left-hand thread), head diameter 129 mm, trimmer line 2.4-3.3 mm.

For EFCO DS220T, DS240T, DS26004T, DS3200T, DS3800T. The head is easy to disassemble and maintain. Seat nut M101.25 (left-hand thread), head diameter 108 mm, trimmer line 2.0-2.7 mm.

For EFCO DS220T, DS240T, DS26004T, DS3200T, DS3800T. head can be easily disassembled by hand without tools. M101.25 nut (left-hand thread), head diameter 115 mm, trimmer line 2.0-3.0 mm.

For models EFCO DS220T, DS240T, DS26004T, DS3200T, DS3800T. Quick filament loading. M101.25 nut (left-hand thread), head diameter 116mm, 2.4-3.3mm trimmer line.

For EFCO DS220T, DS240T, DS26004T, DS3200T, DS3800T. Head made of high-strength plastic. M101.25 nut (left-hand thread), head diameter 122mm, trimmer line 2.0-3.0mm.

For EFCO DS220T, DS240T, DS26004T, DS3200T, DS3800T. Extended service life for heavy-duty applications. M101.25 nut (left-hand thread), head diameter 123mm, trimmer line 2.0-3.4mm.

For EFCO DS220T, DS240T, DS26004T, DS3200T, DS3800T models. Quick line loading. Longer service life due to metal coated trimmer head nut. Nut M101,25 (left-hand thread), head diameter 116mm, trimmer line 2.4-3.3mm.

Semi-automatic line feed, Comfort fast line threading, M10x1 internal thread.25, blister.

Semi-automatic line feed, Comfort fast line feed, metal line feed button, M10x1 internal thread.25, blister. Fits all Patriot gasoline-powered trimmer models with straight boom.

Semi-automatic line feed, M10x1 female thread.25, blister. Fits all Patriot gasoline trimmers with straight line: PT 3045/3055/3355/4355/3155T, T 533/535/545/552 Pro, ET 1000/1200/1255.

Mechanical line feed, M101,25 (left-hand thread), blister. Suitable for all Patriot gasoline and electric straight trimmers: PT 3045/3055/3355/4355/3155T, T 533/535/545/552 Pro, ET 1000/1200/1255

Heavy-duty, professional semi-automatic spool, sturdy, compact, robust cap mechanism, easy threading of lines, universal fit for 10, 12 and 20mm diameter, blister. For straight shaft trimmers.

Semi-automatic, M101.25 (left-hand thread), blister. Suitable for all straight bar Patriot gasoline and electric trimmers: PT 3045/3055/3355/4355/3155T, T 533/535/545/552 Pro, ET 1000/1200/1255

Line reel. For PATRIOT ELT-1150, Lesnik 105/115, Home Garden ELG 1000 electric trimmers. Seat M81.25 (right-hand thread)

Lightweight metal cage for fastening 4 lengths of line. Can be used with PATRIOT, MAXCUT, HOME GARDEN, MTD and other trimmers with similar characteristics. Fitting socket 25,4 mm, line diameter 2,5 mm.

Semi-automatic spool for Patriot PT 360/380/480 trimmers. Can be used with trimmers with similar characteristics. Seat. 7 mm slotted. 1.2 mm line diameter. Length of line 6 m.

Rugged, lightweight mechanical reel for bent-boom trimmers. (For gasoline and electric trimmers with bent rod (PT 2340/2540, PT2540ECO, ELT 800/1000/1200, GG224). socket. Allen key plus nut (HEX 15,6).

For: PATRIOT T552 PRO PLUS, PT553, PT536J, PT545, PT546J, PT555, PT415, PT545PRO, PT3045, PT3055, PT3355, PT4355, PT 3155T, T533PRO, T535PRO, ET1200, ET1000, BEST RM1000-2BT, ET1255. Easy disassembly and simple maintenance. M101.25 nut (left-hand thread), head diameter 108 mm, trimmer line 2.0-2.7 mm.

For the PATRIOT T552 PRO PLUS, PT553, PT536J, PT545, PT546J, PT555, PT415, PT545PRO, PT3045, PT3055, PT3355, PT4355, PT 3155T, T533PRO, T535PRO, ET1200, ET1000, BEST RM1000-2BT, ET1255. Easy disassembly and service. Bearing nut M101,25 (left-hand thread), head diameter 123 mm, trimmer line 2.4. 2.3 mm.

For PATRIOT T552 PRO PLUS, PT553, PT536J, PT545, PT546J, PT555, PT415, PT545PRO, PT3045, PT3055, PT3355, PT4355, PT 3155T, T533PRO, T535PRO, ET1200, ET1000, BEST RM1000-2BT, ET1255. The head can be easily disassembled by hand without using additional tools. M101.25 nut (left-hand thread), 115 mm head diameter, 2.0-3.0 mm trimmer line.

For: PATRIOT T552 PRO PLUS, PT553, PT536J, PT545, PT546J, PT555, PT415, PT545PRO, PT3045, PT3055, PT3355, PT4355, PT 3155T, T533PRO, T535PRO, ET1200, ET1000, BEST RM1000-2BT, ET1255. Quick cord loading. Seat nut M101.25 (left-hand thread), head diameter 116 mm, trimmer line 2.4-3.3 mm.

For the models PATRIOT T552 PRO PLUS, PT553, PT536J, PT545, PT546J, PT555, PT415, PT545PRO, PT3045, PT3055, PT3355, PT4355, PT 3155T, T533PRO, T535PRO, ET1200, ET1000, BEST RM1000-2BT, ET1255. Cap made of high-strength plastic. Bearing nut M101,25 (left-hand thread), head diameter 122mm, trimmer line 2.0-3.0mm.

For PATRIOT T552 PRO PLUS, PT553, PT536J, PT545, PT546J, PT555, PT415, PT545PRO, PT3045, PT3055, PT3355, PT4355, PT 3155T, T533PRO, T535PRO, ET1200, ET1000, BEST RM1000-2BT, ET1255. Extended service life for heavy-duty applications. M101.25 nut (left-hand thread), head diameter 123 mm, trimmer line 2.0-3.4 mm.

For the PATRIOT T552 PRO PLUS, PT553, PT536J, PT545, PT546J, PT555, PT415, PT545PRO, PT3045, PT3055, PT3355, PT4355, PT 3155T, T533PRO, T535PRO, ET1200, ET1000, BEST RM1000-2BT, ET1255. Quick line loading. Extended service life due to metallized trimmer head nut. Fit nut M101.25 (left-hand thread), head diameter 116 mm, trimmer line 2.4-3.3 mm.

For the PATRIOT T552 PRO PLUS, PT553, PT536J, PT545, PT546J, PT555, PT415, PT545 PRO, PT3045, PT3055, PT3355, PT4355, T533 PRO, T535 PRO, ET1200, ET100, ET1255. Fast line loading. High-strength plastic. Metallized nut of the trimmer head. Fit nut M101,25 (left-hand thread), head diameter 125 mm, trimmer line 2,0-3,0 mm.