How to repair a tall -tank trimmer for grass with your own hands. How to get to the saapun?

Repair of plastic gas tank, independently eliminate leak

The leakage of the gas tank is a rare phenomenon, but such a problem can happen to each. In general, plastic gas tank is eternal (namely plastic gas tanks are installed on most existing cars), as it is protected from corroding gasoline. However, he is threatened with other problems. sandblast and any mechanical damage. Even if the gas tank leaked, this is not a reason to throw it out, because it can be quite budgetary to repair it.

If the question is about high.quality independent repair of the gas tank. the surface must be prepared. The preparation consists in draining the gas tank, cleaning (including the processing of the skin) and degreasing the repair area. Of course, it will be best to get a gas tank from under the bottom of the car, but repairs can be done without removing.

In the case of breaking the gas tank on the road. the preparation of the surface for repair can be neglected. About how to carry out repairs in such hardcore conditions. just below.

Repair of epoxy resin

You can eliminate the flow of plastic gas tank using ordinary epoxy resin. Degreasing and clusing the area, apply the mixed epoxy tar to the crack. If it is quite large and it is not possible to block it completely. you have to get confused a little.

Take a piece of fabric, the area of which is slightly larger than a crack, and apply glue on its surface. After that, swing the crack with this fabric, making efforts when pressing the fabric. Thus, it needs to be kept at least 30 seconds. Когда ткань приклеилась – нанесите еще клея поверх ткани таким образом, чтобы поверхность оказалась полностью перекрыта. In this matter, “more” does not mean worse “. The main thing is to avoid slices of epoxy resin into the tank itself.

When such a patch dries, you can additionally treat the surface with a sealant to avoid wear of epoxy resin (as a result of the same sandblasting) and to fix the result.

In the field, the process is similar. Only here you need to use fabric impregnated with adhesive composition. Put the epoxy on the engine (in this way it will warm up, and as a result, it mixes and freezes faster), soak it with a rag and glue directly on the hole. Also use the remaining glue. to consolidate the result.

This method of repair will at least allow you to get to the next hundred. We do not recommend using it as a major overhaul. For this, there are ways that you will learn about next.

Malfunctions and their elimination

Electric and gasoline trimmers have typical breakdowns and malfunctions. For devices running from an internal combustion engine, this is:

problems in the carburetor;
engine breakdown;
problems with the fuel system;
breakdown of the gearbox, starter, muffler;
blockages;
Air filter breakdown;
Problems with ignition coil.

Electric units have specific breakdowns:

With simple problems, you can make a trimmer repair for grass with your own hands.

Why is a trimmer not starting for grass

The most common reason that the unit does not start is the use of poor.quality fuel. The choice of gas stamps below AI-92 can disable the lawnical mower. If high.quality fuel is used, you need to look for other reasons. To do this, carefully check all nodes and systems. The checks are subject to:

The device may not start after prolonged downtime. Before turning on a trimmer for grass, you need to study well the instructions for operation. The solution of many problems is indicated in it.

If it stalls when you press the gas

There are several reasons why a trimmer for grass stalls when gas is pressed:

The first reason is the dumping of the carburetor.
Fuel valve.
Fur valve blockage.
The weakening and sagging of the carburetor cable or sagging of the fuel intake hose.

So that the described problems with the lawn mower do not arise, you need to carefully monitor the condition of the device and its blocks. Timely cleaning, washing of the unit and spare parts allow you to increase its life.

Starter breakdowns

The most difficult breakdown of the starter occurs when the rope is broken and winding it into the flywheel of the operating engine. As a result, the spring may burst and the pulley plunges. In this case, only a complete replacement of the spare part will help. This breakdown rarely occurs. often:

In this case, it is easy to fix the starter yourself. The manufacturer has prepared a step.by.step instruction for this.

REDUTOR Repair

Caring for the motorcade gearbox consists in the timely lubrication of the unit. The absence of one can lead to rapid wear of the gear and jamming of the gearbox module.

The main malfunctions of the trimmer gearbox for grass:

severe heating of the gear component due to the use of low-quality lubrication or its absence;
shaking of the shaft during the rotation of worn bearings;
staggering or flowering from the bar of the gear ratio as a result of damage to the case;
Lack of rotation of the output shaft with a knife due to wear on the teeth on the gears.

Most of the malfunctions in the gearbox are associated with the destruction of bearings.

This happens due to the use of low-quality lubrication or its complete absence. Another reason for the failure of the gearbox is the operation of a trimmer for grass at the limit of its capabilities and the hit of foreign objects. To replace a faulty bearing, a gearbox is disassembled.

Features of the repair of electric models

Electric models of trimmers operating from the network have several main blocks:

Each electrimmer block has specific problems. In the mechanical part, they depend on the presence of a fishing line used as a cutting element. Reasons for the termination of work:

You can identify the problems of the electrical part of the electrocos using special tools:

To eliminate problems, a soldering lamp is needed.

a malfunction of the power cable;
problems with an outlet and fork;
the failure of the control handle;
combustion of the starter winding, engine replacement is required;
Contact breaks can be corrected independently using a soldering lamp.

How to adjust the carburetor

The module adjustment is carried out by the manufacturer. During the operation of the device, after repairing or cleaning the module, it becomes necessary to adjust the carburetor.

Carburetor setup does not require replacement of spare parts. Debugging is done with the help of 3 screws that are available in the design:

L. controls the supply of fuel at low speeds;
H. controls the fuel consumption and temperature, and is also responsible for supplying gasoline at high speeds;
T. is responsible for the idle engine.

Adjustment of the carburetor of the trimmer for grass is carried out after the engine warms up. For this, 10 minutes of operation of the device at idle will be enough. The rotation of the mowing head at idle allows you to start directly to debug the screw t. It is turned counterclockwise to the cessation of rotation. Then the screw h is scrolled to the right and left to find the position in which the idle speed will be maximum. The screw is turned off on ¼ full turnover counterclockwise from the found point, this will be the working position.

According to the same technique, the screw l. After repairing the carburetor, the module is necessarily tuned so that the device works correctly.

Repair of the gas tank Motokosa (Treimer)

Repair of a broken gas tank Motokosa, through soldering and reinforcing weaknesses. In the same way, I repaired the tank cover in which I twisted the upper part. Soldered with a net and everything is fine. Repair Motokos (disassembly) A large selection of new motos for buying: Check out the entire menu of my channel: Parks from China Women’s clothing and shoes: jewelry and everything for beauty: Electronics: all sorts of things from China: Children’s things: Men’s clothing and shoes: China- Time checking: tests Reviews: Repair of Electronics: Motokos, Lawn Models, Benzo-Tyrmers: Agronomia, Unoic Tractor, Devices, Homepage: Group in VK: https: // vk.COM/sergeypashchenko My Instagram: http: // Instagram.COM/Paschenkosergey I’m in Periscope: Subscribe to my channel: https: // www.YouTube.com/user/thesergeypashchenko will become a YouTube partner via Medea Network: My Second Channel: SP-Life Mail for suggestions: PASENKOSS@gmail.com do not forget to evaluate this video, leave a comment and subscribe to the channel to keep abreast when a new video comes out. Your activity helps in the development of the channel and inspires me to create new videos. Thank you for watching!

Repair of the gas tank Motokosa (Treimer)

Repair of a broken gas tank Motokosa, through soldering and reinforcing weaknesses. In the same way, I repaired the tank cover in which I twisted the upper part. Soldered with a net and everything is fine. Repair Motokos (disassembly) A large selection of new motos for buying: Check out the entire menu of my channel: Parks from China Women’s clothing and shoes: jewelry and everything for beauty: Electronics: all sorts of things from China: Children’s things: Men’s clothing and shoes: China- Time checking: tests Reviews: Repair of Electronics: Motokos, Lawn Models, Benzo-Tyrmers: Agronomia, Unoic Tractor, Devices, Homepage: Group in VK: https: // vk.COM/sergeypashchenko My Instagram: http: // Instagram.COM/Paschenkosergey I’m in Periscope: Subscribe to my channel: https: // www.YouTube.com/user/thesergeypashchenko will become a YouTube partner via Medea Network: My Second Channel: SP-Life Mail for suggestions: PASENKOSS@gmail.com do not forget to evaluate this video, leave a comment and subscribe to the channel to keep abreast when a new video comes out. Your activity helps in the development of the channel and inspires me to create new videos. Thank you for watching!

The engine is faulty

All breakdowns that are possible in the engine are divided into two main categories. The first can be attributed to those that are not possible to fix it independently. For example, it can be a marriage that can only be fixed by replacing the tool. And there is another group of breakdowns that are subject to even non.professional.

So, if the lawn mower operates for more than 15 minutes, then the engine may start overheating. You can fix this by turning off the tool for several minutes.

Also, overheating can be initiated by another reason, for example, by the fact that the starter’s grille was clogged, namely, parts of grass and shrub fell into it.

It is extremely important to use only fuel, which is indicated in the technical description for the tool, otherwise, the problems of the carburetor will be overtaken very soon.

When using poor.quality or inappropriate raw materials, it will at least be clogged, and even rust may appear as a maximum. And, therefore, it will not be possible to ignition of the lawn mower and will have to contact specialists.

In some cases, during operation, fuel leakage may be observed. This should not be, since the consequences can also lead to a more serious breakdown. Most often, fuel follows due to the fact that the corresponding hose has clogged, which can simply be blown.

The frequency of replacing the candle

Despite the fact that spare parts for the lawn mower are enough to purchase in any specialized store, the owner should have an understanding at what point to change them in the tool most correctly.

Before you go for a new part, it is necessary to disassemble the motor and figure out whether the replacement is necessary or it will be enough to clean it. For this, first of all, there is an instruction for the repair of this tool.

Often, a lawn mower may not work due to the fact that a candle was not changed. But do not immediately rush to change it, first it is quite well cleaned, since the ingress of dirt in many cases leads to various errors, so it is extremely important to remove it in a timely manner.

In addition, after after cleaning, the whole structure will become more visible, which means it will be noticeable if the case is in the departed contact on the connecting wire. Often the problems of candles arising from the candles are mechanical in nature.

Description

The key purpose of a tank for a trimmer for grass is storage of fuel. The market today presents various configurations of the gas troops for motorcycle, which differ in volume, material and other parameters. Depending on the capacity of the tank, the duration of the uninterrupted operation of the braid for grass during operation is determined.

The gas tank is worn in the same way as other components of the benzotrimer. To prevent premature damage to the walls, manufacturers provide for their protection in the form of plastic plates or steel.

The procedure for cleaning the soundtress

Simple purification method. use a sewing needle. Before cleaning the valve, make sure that it is clogged. It is not difficult to do it.

Remove the carburetor (it must be disconnected from the fuel hose), estimate the number of traces of fuel.
If the fuel flows, and the saapun remains clean, then everything is in order with it and you need to continue diagnostics. If a weak stream of fuel arises from the gas pipeline, you can have no doubt that the sapun needs careful cleaning.

Important! If, after cleaning, the chainsaw shows an increase in revolutions when idling, do not rush to panic and disassemble the tool or attribute to the workshop. After cleansing, this behavior of the engine and carburetor (their interaction leads to an increase in the speed at idle) is considered the norm. If this feature is alarming, you can slightly adjust the idle screw located on the carburetor and has a mark of T.

The procedure for cleaning the soundtress

Simple purification method. use a sewing needle. Before cleaning the valve, make sure that it is clogged. It is not difficult to do it.

Remove the carburetor (it must be disconnected from the fuel hose), estimate the number of traces of fuel.
If the fuel flows, and the saapun remains clean, then everything is in order with it and you need to continue diagnostics. If a weak stream of fuel arises from the gas pipeline, you can have no doubt that the sapun needs careful cleaning.

What is a sapun and why it is needed on a trimmer

The fact of the trimmer is, and why it is intended, far from many experienced kosari and instrument owners know. What is it, and how the detail affects the work of the lawn mower, it’s time to figure it out. Before you understand the question of what is called a benzokos as a benzocosa, it should be noted that this part has a direct impact on the launch of the tool engine.

The cabin is called the valve that passes the air in one direction. This part is called a check valve, through which the pressure in a closed container occurs. This tank on a gas tank is a fuel tank. Why do you need to balance the pressure in the tank of the lawn mower, and how the check valve affects the operation of the tool engine?

To understand the purpose of the check valve on a gas station, we will briefly consider the features of fuel supply to the carburetor.

The fuel poured into the tank is sucked into the carburetor during engine operation. For this, the tank has a hose that is connected to a carburetor
The membrane, which, by creating a vacuum, absorbs its absorption, is responsible for the pumping of the fuel from the tank to the carburetor
When operating the engine, a gradual devastation of the tank occurs, and since the tank is a completely tight container, in the process of reducing the fuel, a vacuum or vacuum is created
The higher the vacuum (grows with a decrease in the amount of fuel in the tank), the more difficult it is for the carburetor to pump fuel
To eliminate the effect of the vacuum in the gas mushroom tank, a check valve is used, which passes the air in one direction, and does not allow fuel to flow out

The sapun is aligned with the pressure of the trimmer for the grass in the gas tank, and if this part is malfunction, the engine starts up. This difficulty is that the carburetor membrane simply does not have the opportunity to suck fuel due to the vacuum formed inside the container. The check valve works as follows:

When creating pressure inside the tank, air leaks occurs, thereby the vacuum decreases
Air leakage into the tank when the chainsaw is operating excludes the flow of the fuel mixture from the tank

How to seal the fuel tank of a trimmer for grass

We drive a car to the observation pit or overpass;
We outline the place of flow with chalk;
We dismantle the fuel tank from the car;
We pour the remnants of gasoline in other words of diesel fuel;
We dry out in the open air, because the pairs of chemical reagent are explosive;
Using a rag and soap solution, we clean the gas tank from the residues of the resin, dirt, and other impurities on the outside;
For cleaning heavily derived compounds, we use rough sandpaper;
The surface of the gas tank is degreased using acetone. This function must be carried out a couple of times, because how excluded the degreasing of the glue of the gas tank material is carried out;

Even more information about repairing and choosing a tool here www.Looktool.Ru enter, of course, everyone is happy about everyone.

For gluing, you need to use glue of a viscous mixture, otherwise the effect is not to achieve an option.

We cut the fiberglass shreds with such a macar so that they protrude 1-2 cm. more perimeter of crack or other damage. We impregnate the fabric shreds carefully in the eboxite;
Gently apply fiberglass on the surface of the gas tank so that there are no air bubbles left, otherwise eliminate the shortcomings;
With the help of a rag, remove excess glue and resin;
Smoothes the glass wheel with a small piece of plastic for the even platform;
After that, we proceed to the imposition of the second ball, we carry out a similar procedure. Depending on the degree of damage to the gas tank, it is determined with the number of balls of fiberglass. Accordingly, the minimum damage will require the minimum number of fiberglass balls, the deeper zones of the lesion will require more balls.

The driver is note, it must be remembered that the quality of the rest of the structure depends on how the first layer is laid.

Each subsequent layer should be slightly wider than the previous one and with an interval of 15-20 minutes.

In addition, the last layer is impregnated with an additional aluminum powder, which can be purchased in a car shop.

After a day, the design will completely dry and harden. You can process it using fine grinding paper.

We proceed to painting or primer, depending on the need.

Cold welding is used similarly to the above processes. Despite advanced technologies in the form of welding, many drivers prefer old proven and durable methods. So that the question is than Clog The gas tank is already disassembled. A similar procedure can be carried out both in garage conditions and at a car service, depending on your decision.

How and with what can you close a crack or hole in a gas tank

What are the effective methods and how to seal the gas tank for the possibility of its further operation? Such issues will be considered in this section. After all, this topic is more concerned with used cars, and even then domestic production.

Structurally, gas troops are practically not protected by external damage, in contrast, from foreign analogues. Often small fractions of gravel, gravel, asphalt, bouncing off the rear wheels gradually ruin the shell of paint and primer, bringing irreparable harm to the metal. After some time, the metal begins to rust. The driver begins to notice a fuel leak.

Preparation stage and epoxy gluing

For gluing, it is necessary to use glue of a viscous consistency, otherwise the effect can not be achieved.

We cut the fiberglass flaps so that they protrude 1-2 cm. more perimeter of crack or other damage. We impregnate the fabric shreds carefully in the eboxite;
Gently apply fiberglass on the surface of the gas tank so that there are no air bubbles left, otherwise eliminate the shortcomings;

With the help of a rag, remove excess glue and resin;

Smoothes the glass wheel with a small piece of plastic for the even platform;

After that, we proceed to the imposition of the second ball, we carry out a similar procedure. Depending on the degree of damage to the gas tank, it is determined with the number of balls of fiberglass. Accordingly, the minimum damage will require the minimum number of fiberglass balls, the deeper zones of the lesion will require more balls.

The driver is note, it must be remembered that the quality of the rest of the structure depends on how the first layer is laid.

Each subsequent layer should be slightly wider than the previous one and with an interval of 15-20 minutes.

In addition, the last layer is impregnated with an additional aluminum powder, which can be purchased in a car shop.

After a day, the design will completely dry and harden. You can process it using fine grinding paper.

We proceed to painting or primer, depending on the need.

Cold welding is used similarly to the above processes. Despite advanced technologies in the form of welding, many drivers prefer old proven and durable methods. So that the question is, how to seal the gas tank is already dismantled. A similar procedure can be carried out both in garage conditions and at a car service, depending on your decision.

Quite frequent phenomenon that can catch the driver in the most unforeseen situation. The failure of the gas tank is a serious problem that needs to be at least partially eliminated at the site of the accident. This will allow transporting the car to the nearest service center, where it will be possible to conduct a capital examination and repair. DIY gas tank repair is not too difficult for people who have some knowledge about such.

The location of the gas tank. the right lower corner of the rear sector of the vehicle. This is due to ensuring security for the driver and passengers, as well as the formation of the right center of gravity in a car that allows to improve its handling. However, the lower area most often suffers from constant physical effects, which leads multiple damage to all the mechanisms located here. The fuel tank is no exception.

How to make a crack in a metal gas tank

The cause of the depressurization of the gas tank may be a crack or corrosion in the steel building. Cracks are characteristic of plastic and aluminum tanks. The cause of their appearance may be a blow in a collision, deep pothole. Metal tank rusts after mechanical damage by components of the road surface.

How to Maintain Your String Trimmer

The steel fuel tank is restored by cold welding or using epoxy resin and fiberglass. In both cases, it is necessary to prepare a container for repair work.

Cordless SharperBlade Stringless Lawn Trimmer 2021 #Shorts

To determine the place of leakage, the car is put on the observation pit or overpass, where you can access the inspection of the gas tank. Damage is marked with chalk or marker. It is important to drain fuel residues, dismantle the tank.

Sources:

https://autoread.ru/soveti/remont-plastikovogo-benzobaka-samostoyatelno-ustranyaem-tech.html
https://specmahina.ru/gazonokosilka/remont-trimmerov.html
http://www.nofollow.ru/video.php?c=Xa_OBOqoPWI
http://www.nofollow.ru/video.php?c=Xa_OBOqoPWI
https://dacha73.ru/remont-benzokosy-svoimi-rukami/
https://drillzone.ru/rezhushchie/remont-benzobaka-trimmera-svoimi-rukami.html
https://drillzone.ru/rezhushchie/remont-benzobaka-trimmera-svoimi-rukami.html
https://moneyinvestnews.ru/chem-zakleit-plastikovyy-benzobak-trimmera/
https://moneyinvestnews.ru/chem-zakleit-plastikovyy-benzobak-trimmera/

Grass Trimmer grass, repair, tall, tank, trimmer, your