How to run up a new trimmer for the grass hoper. The gas mower is gasoline

trimmer for grass Hope manufacturer

Before using a gasoline trimmer for grass for grass (lawn mowed), it is required to carry out its preliminary running.in. Playing is needed to extend the engine service, because moving parts during the period of the runaway should first work to each other. In addition, during running.in, you can acquire certain skills in working with two.stroke gasoline technique

This is important for those users who first work with the Kamoto benzoca on the brand

The gas mowing engine is running out with an average and slightly higher than the average load on the engine in a cyclic operating mode: the mowing of the grass lasts 1. 1.5 minutes, then 15. 20 seconds idle. The engine will acquire maximum power after the production of several full tank gas stations.

You can not run into the engine at idle, because the formation of a large amount of soil provokes the occurrence of piston rings or the exit of the spark plug out of order. Recommended proportion of gasoline A-95-2T oil: 1000 ml-30 ml of oil.

We recommend using two.stroke oils of the following brands: Kamoto, Oregon, Stihl, Husqvarna, Makita, Hitachi, Dolmar, Ravenol. It is advisable to purchase oil in specialized stores, to confident that it is not fake.

Before starting work, carefully read the instructions and make sure that the tool is completely and correctly assembled. Check the correct installation and reliability of the attachment of all the elements of the tool, especially the trimmer coil and cutting knife/disk; It is advisable to type two.stroke oil with a medical syringe and then add to the mixing container with gasoline

This must be done for a more accurate measurement of the amount of oil added; Mix oil and gasoline only in a clean bowl pay attention to in the container where you will stir two.stroke oil with gasoline, there is no waste, water residues or other liquid; It is important to observe the mode of work with the tool: 30 minutes of work, 10-15 minutes break; After each use of the tool, we recommend drain the fuel mixture into a clean container, then start the lawn mower until the full consumption of the fuel mixture remained in the carburetor. Try to use only a fresh fuel mixture of 2T oil with gasoline, which defended more than 10-14 days, changes its properties; If necessary, add grease (except for lubricant on a graphite basis) to the reducer of the lawn mower; At the end of the work, clean the tool from the remnants of the grass and sticky dirt; Regularly check the protracted bolts on the starter, the base of the tank and others

Due to high revolutions, the bolts periodically unwind and they must be tightened; Regularly blow the air filter and the spark plug. Clean the soil on the spark plug with an ordinary rag. If necessary, replace the spark plug.

What oil to choose for refueling in a trimmer for grass or types of lubricants

Trammers for grass and lawn mowers operate on two.stroke engines that have a simplified design. Rarely, but there are models of trimmers with 4-stroke engines that work on pure gasoline. Two.stroke.type power units do not have a compartment for pouring motor oil (oil crankcase), due to which the weight of the tool is reduced and their cost is reduced. If the rotating details of the motor are not lubricated, then in the end they will quickly fail. To prevent this, a trimmer for grass is seasoned not with clean gasoline, but a mixture with butter. What kind of oil to dilute with gasoline for a trimmer for grass?

First, remember or find out what types of oils are produced by chemical composition:

• Mineral fluids. designed for small power technology, which has air cooling. This is the cheapest type of lubricant for motors
• Semi.synthetic substances. they are used for technology, which has air and water cooling
• Synthetic. suitable for all types of motors with different types of cooling. They do not require frequent replacement, and this type of lubricant is several times more expensive than mineral and semi.synthetic

It is interesting! The main thing when choosing oil is not to fall on the fake, since today you can very often find different types of lubricants for two.stroke engines, which consist mainly of low.quality oil products.

Characteristics

Many gas stamps use a mixture of gasoline and lubricating fluid as a fuel. And Hooper was no exception. To prepare the mixture, you need to take this ratio: 1 part of the adapted engine oil and 25 parts of gasoline with an octane number of at least 92. If you do not adhere to this ratio, then the motor will quickly become unusable and begin to break.

Despite the fact that the lawn mower does not need to be running out, it is advisable to use only half of the power when starting. For the first two gas stations, oil should be added 10 % more than the recommended volume. Do not try to harvest the fuel mixture with a margin, as the fuel is aging and becomes not suitable for use.

To extend the life of the motor, adhere to the following rules:

• Do not use dirty gasoline. Be sure to add the oil!
• It is forbidden to use a trimmer for grass at large speeds without load.
• Since the engine is 2-stroke, the use of oil for 4-stroke engines is prohibited.

After 10 hours of operation, the lawn mower is needed:

• Check the condition of the muffler;
• Clean or replace the air filter;
• Check the gap between the contacts of the spark plug. It should be 0.6-0.7 mm;
• Clean ventilation holes;
• Add oil to the gearbox.

The manufacturer does not recommend that the power unit independently repair. And in the event of any breakdowns, you should contact the service center.

To reduce the load on the engine and prevent overheating after every 45 minutes of operation, a technical break is made for 10-15 minutes, while completely drowning the motor.

Valera:

“I wanted to leave a review on the Khoper 052, because I really liked the model. I collected everything quickly and without problems. Not light, but easy to use and has not yet broken, but used only one season. The motor is powerful and the bushes mowing with a bang.””

“I decided to leave a review, since I really liked the model. Work easy, mows perfectly. There were doubts about the quality, but they were dispelled after the operating season. As a shortage, I can note that it was lacking in the set of protective glasses and the bar could be made detachable because it is difficult to transport.””

trimmer for grass gasoline hopper 043 farmer, 2.5 kW

You can’t do without a trimmer for grass if you have at least a small personal plot. However, he will perfectly cope with thick grass on a section of any size. A big plus of the lawn mower is complete freedom of movement and the ability to process the territory not only directly near the house, but also at a large distance from it.

• Easy access to air filter.
• Convenient control on the handle.
• Hard shaft on 6 support bearings.
• Reinforced gearbox.
• Spool with a fast change of fishing line.
• Winter dies’ disk.
• Belt: Range.
• Type of rod: straight, non.vegetable.
• Handle: bicycle.
• Engine volume: 43 cubic meters. cm.
• Engine: 2-stroke with air cooling.
• Weight: 8.3 kg.

Technical information

Own, developing network of supermarkets “Order” and pickup points, cooperation with the best transport companies, monitoring the time of setting orders. all this allows us to deliver goods anywhere in a short time!

You no longer need to remember passwords-access to your personal account is carried out through a unique SMS code. No one can find out your personal data, use bonuses or discount on a discount card.

The Loyalty Map of the Network “Order”. discounts for regular customers, as well as prizes for reviews about goods. Get discounts on goods in the online store and retail chain “Order”!

In the Order online store, are much lower than in retail stores. In addition, registered users regularly receive discount coupons and special offers.

Diagnosis of the candle channel

What to do if the used fuel mixture is in perfect order, but a trimmer for grass is still not started by gasoline? The reasons for the refusal of the mechanism may lie in excessive moisture of the candle channel. To diagnose and eliminate the problem, it is necessary to do the following:

• To twist the candle. Wipe it thoroughly, and then dry it.
• Drain excess fuel in the chamber through the corresponding candle hole.
• Clear the old candle if there is a dozen on its surface. Cope with the task will allow the use of a conventional ladies’ nail file or file.
• When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the lumen.
• Collect a functional block back.
• Try to start a trimmer for grass.

It is recommended to perform a candle channel to dry for at least half an hour. However, in no case should you resort to the calcination of its elements. After all, heating the spark plug can lead to its final corruption. Что предпринять, если обслуживание функционального блока было выполнено в соответствии вышеуказанным рекомендациям, но триммер для травы не заводится, искра есть при этом? In this case, it should be treated with gasoline threaded connection. The latter does not need to be saturated abundantly fuel. It should only be slightly moisturized. Resort to such actions should be to ensure the ignition. After all, no matter how much the candle gives a strong spark, in an absolutely dry chamber there simply will not be something to ignite.

If even in this case a trimmer for grass does not start, it is worth evaluating the quality of the contact between the high.voltage wire and the candle. In the absence of a spark (in the presence of a reliable connection between the indicated elements), most likely, the problem is caused by breakdown of the ignition unit. In this situation, you will have to turn to the services of masters who will reinstall the knot.

The first launch of the lawn mower

The correct first launch and running of the lawn mower is very important steps at the beginning of the operation of a new tool. On the one hand, they allow you to save the gasoline engine motor, laid down by the manufacturer, since at this stage there is a grind of moving units and parts. On the other hand, the first necessary skills in working with a trimmer are acquired, if we are talking about the first tool in life.

The first launch of the lawn mower

The correct first launch and running of the lawn mower is very important steps at the beginning of the operation of a new tool. On the one hand, they allow you to save the gasoline engine motor, laid down by the manufacturer, since at this stage there is a grind of moving units and parts. On the other hand, the first necessary skills in working with a trimmer are acquired, if we are talking about the first tool in life.

Inspection of the reducer of the lawn mower and its lubrication

Checking the gearbox before starting a gasoline trimmer for grass must be carried out on a regular basis. The lack of lubrication or its small amount increases the friction of the gear gear of a gearbox operating at fairly high speeds. As a result, overheating and gears occurs. Motokosa gearbox fails. To prevent the occurrence of such a breakdown during operation and the regular inspection helps.

If, before the launch of a gasoline braid for grass, an insufficient amount of lubrication in the gearbox or its absence in the case is laid “litol”. To do this, it is necessary to unscrew the screw on the bend of the gear housing and the “lilest” in the amount of 1-2 ml.

Working with a gasoline trimmer for a long time, every 8-10 mothers add grease to the gearbox of the bar.

How to start a motorcycle

The peculiarity of any technique with a two.stroke engine is a hard algorithm of cold launch, which must be strictly observed.Good afternoon, dear subscribers and guests of the channel.

The other day, a man asked me to see his mower.

The complaint was that the tool would not start. The client said that he bought a mower recently, worked only once. An attempt to start a motorcycle for a second time was unsuccessful.

Such leaks indicate that the mower shifts fuel, but the user practically did not work, and as I later found out from the client, they appeared during an unsuccessful launch.

Now everything fell into place. This lawn mower is completely serviceable, but the client would not be bad to read the instructions, especially the section in which the process of “cold” launch is described.

The result of proper run.in a gasoline trimmer for grass

After you have been running the lawn mower by the instructions, as a result, we get a tool ready to work. Of course, it is best not only to read the stages, but also to see the crowding on the video from specialists. The result of the correct actions will be obtained:

• trouble.free operation of the benzo tool for a long time;
• high.quality start of the device and stability of the submitted power;
• lack of unforeseen repairs of a trimmer for grass after high.quality pounding;
• Lack of overheating.

In this regard, the primary processing of the Chinese braid for grass is an integral part of the quality work of the device that can work flawlessly using benzos knives or cutting fishing lines of different diameters when processing territories available in the special store “Spit for grass”.

We proceed to running the lawn mower

After starting, do not rush to immediately run the trimmer for the grass. Let the engine idle for 5 minutes. While heating is going on, adjust the air supply to the air damper with a lever so that the rogue with a fishing line or with a knife does not rotate. As soon as the tool warmed up, we completely open the air supply to the corresponding lever to the “ON” position and squeeze the gas trigger for 1/2 and hold the seconds of seconds 30. Then we drop the gas, let the trimmer work on xx 30.40 seconds. In this mode we continue 10 minutes 15. Then we mock and let it rest for 15 20 minutes.

Having cooled the lawn mower, we continue to run the engine according to the previous scheme. Start a hot, a trimmer for grass should already be with an open air damper. Try not to hold the gas for a long time, since the movable details of the tool only rubbing each other. And do not let the engine work at idle for a long time as it can overheat.

The next stage is the run.in a gas reducer gearbox for grass. To do this, select a plot with soft young grass. Kosim 5 10 minutes with 1/2 2/3 from full gas. After we take a break for 20 25 minutes. Repeat the cycle 3 4 times.

In general, therapist for the lawn mowing according to the described algorithm is carried out until the fuel mixture in the tank is fully generated. After which the tool is ready for long.term work. In the process, follow the temperature regime of the gearbox and the motor. They should not overheat.

Characteristics

It should be noted that the gas braid is very simple to operate. It is enough to see how other users use this device to start using it completely. The performance of the main technical functions is intuitive and does not require difficulties in practice. It is also easy to properly run a gas trimmer for grass. over, there is practically no difference between devices in the household and professional categories.

The key difference is engine type. As for the technology for professionals, it is more powerful and gives more speed. A two.stroke engine is more often used in household models. Four stroke units are more reliable and require great efforts, so they are suitable for special conditions, difficult and overgrown sites.

Preparation for the first launch of the lawn mower

Before carrying out the first launch of the lawn mower, it is necessary to perform a number of consistent actions:

We recommend that they perform them not only when buying a new trimmer for grass, but also when preparing an old tool for the new season after storage.

Basic rules and techniques when working with a motorcycle

For the merit of not bad cat results, it is also fundamentally correct to operate and care for a motorcycle. Even if you have been holding a motorcycle for the first time, you will master the right Kosba technique rapidly. The device is simply rotated along the semicircle from right to left, with all this evenly moving forward.

Below we will show for you the main technique and certain techniques, with which you can rapidly mow even huge areas and achieve the best results as a kota.

The main technique of kosba is most often used.

Because the cutting tool is spinning counterclockwise, then in working practice the movement of mowing on the right to the left is more often found.The advantage of this method: mowed grass falls on an already mowed surface.

Large, even surfaces. the right reception.

Large even surfaces for you is most perfect to mow in a square way. The area is distributed in squares, then you always work along the outside to the center.

The main technique in the case of high grass.

With a very highest grass or stiff weed grass, it is recommended to mow in both directions of movement: at first you cut off the right part of the mowing weed in one movement, with the oncoming movement (on the left). the lower. Mowed grass and in this case it remains to lie on the left.

Along the slope. mowing behind mowing.

You will advance perfectly in the way of direct mowing in particular on the slope: scrape one mowing parallel to the slope, and then return back in a beveled strip. Then mow the subsequent mowing. And here, mowed grass always fits on an already mowed surface.

Masterfully bypass obstacles. to bump playlessly.

In order to squint at the trees or shrubs, I do not damage knots or trunks, the cutting thread is most ideal. If many plants are at a small distance from each other, then in front of the kosa is offered. To do this, use the protection of your motorcycles as a guideline. Always lead it specifically along a wood barrel or shrub, and move around them. The barrel remains protected, the territory around the barrel will be scorched.

Inspection of the reducer of the lawn mower and its lubrication

Checking the gearbox before starting a gasoline trimmer for grass should be created on a permanent base. The lack of lubricant or its small amount increases the friction of the gear transmission of a gearbox that works at fairly large speeds. The result is overheating and gears. Motokosa gearbox fails. To prevent the appearance of such a breakdown during use and is helped by constant inspection.

If, before the start of a gasoline braid for grass, the missing amount of lubrication in the gearbox or its absence, Litol is laid in the case. To do this, you need to unscrew the screw on the gear housing and pace the “lilest” in the amount of 1-2 ml.

Working with a gasoline trimmer for a long time, every 8-10 mothers add grease to the gearbox of the bar.

A few more tips when working a motorcycle

A haircut. Keep the head of a trimmer for grass directly above the ground at an angle. Work performs the end of the string. Give the string the opportunity to work at your own speed. Do not press the fishing line for a trimmer to the overwhelmed area! This overloads the engine and mowing head. they can fail or melt!

Cutting. A trimmer for grass is ideal for cutting such a grass that is difficult to get to, using an ordinary lawn mower. In the process of cutting, keep the string parallel to the ground. Avoid pressing the head of the trimmer for grass to the ground, since you can ruin the lawn and damage the tool.

Cutting with a knife. Make a mowing with a pendulum movement from side to side, the movement from right to left will be a worker, and from left to right. will be a repayable. The blade should cut the grass with its left edge (on the dial of the clock. between 8 and 12).

Why cannot be drove at idle

There are many videos on the Internet, entitled as a “proper run.in saw”, where you can see the assigned unit, quietly rumbling at idle, removed from different angles. You can’t do this!

While working at idle, the engine operates at the lowest revolutions, but long-term work in this mode is destructive for the cylinder-piston group. The fact is that the fuel does not burn out completely, part of it settles on the walls of the cylinder and the bottom of the piston in the form of a carrier, interferes with the work of compression rings, works as an abrasive.

In addition, with the clutch turned off, the flywheel, on which the card of the crankcase is mounted, rotates slowly and does not provide proper cooling. As a result, the motor overheats, bulletin appears on the piston and cylinder, which leads to decompression, the saw loses power and stalls periodically.

Working scheme of gasoline technique

If there is no indication of the initial period of operation in the instructions for a chainsaw or trimmer, this sequence of actions should be followed:

• Mix gas and oil in the proportion, which is indicated in the instructions for a normal working regime or at the very saw in the area of ​​the bay neck or gas handle. It is allowed to increase the amount of oil by 10. 20% of the norm.
• Start the engine, taking into account the features of a particular model.
• Having given the saw to work for 15. 20 seconds at idle, you need to press several times, and then hold the gas handle in order to work as the clutch and the chain set in motion.
• Start work by choosing branches for this, branches or thin trunks. It is advisable to carry out the run not on dry, but fresh wood. After 5. 10 minutes of working with a periodic transition to idle (no more than 20% of the total work time), drown the saw.
• Repeat the cycle, increasing the working hours to 10. 15 minutes. After that, the saw can be considered running.

Those who believe that the running.in should take place within a few hours are mistaken: “grinding” is carried out during the first hour of work. The coating of the cylinder and piston of many modern saws is chrome, and during moderate household load it is impossible to somehow influence the physico-mechanical properties of such materials. But by overloading the saw, you can easily overheat the piston and get the bully on the mirror, spoiling the almost new saw.