How To Start A Trimmer Petrol Champion

Petrol Trimmer Won’t Start? Elitech T750 Reasons and Solutions

In general, such a conversation should start with the fact that after buying a garden gasoline tool, it would be better to first familiarize yourself with the instructions attached to it. Then many problems could be avoided. But since this happened, the gasoline trimmer does not start, then you need to look for sources of inoperability. And in this article we will consider the main reasons why the trimmer does not start on the example of the Elitech T750 model, as well as we will tell you general recommendations for using such a tool.

You should start with the banal! Let’s figure out how to properly start a gasoline trimmer. It may be that the reason lies precisely here.

First you need to bring the red toggle switch on the trim bar to the “I” position. This means turning on the power. Then you need to switch the fuel supply lever to the carburetor and use the fuel “suction” button (similar to a pipette, located in the carburetor). This is necessary to supply gasoline to the engine. Return the fuel delivery lever to its original position. Finally, pull the starter handle sharply towards you. The trimmer should work. Try it several times if it doesn’t work the first time. If, after such manipulations, the situation has risen and the gasoline trimmer does NOT start, then you should first inspect it yourself before you take it to the service center. There are two main reasons your garden trimmer won’t start:

• Power circuit breakdown.
• Sun fuel.

• Let’s start with the ignition problems. In most cases, it is caused by the need to change the spark plug in the engine. This is done like this:
• First of all, we have to take care of the safety measures, making sure the trimmer is disabled. We bring the above toggle switch to the “STOP” position.
• Then we remove the rubber protection from the candle and the wiring terminals. Using a special spark plug wrench, we unscrew the spark plug and replace it.
• After that, we assemble the device and carry out the above procedure for starting the trimmer.

The second reason garden tools don’t work is because they run out of fuel. On the Elinech T750, the fuel tank is located near the engine, but on most trimmers it is located there. We unscrew the cap from the tank and fill it with gasoline (the most optimal variant is AI-92, it is inexpensive and does NOT clog the carburetor like the AI-76). Do not forget to add a special oil for engines to the tank, 50 grams is enough for the gas tank, without it the engine will start to “sneeze” and will quickly become unusable. Then we close the tank with a cap, wipe the trimmer surface and our hands with a dry cloth. We also do the above manipulations to turn on the garden tool.

If the petrol trimmer does not start as before, then it makes sense to have it repaired. And the reason for this decision is simple. if you DO NOT have the appropriate skills, equipment repair is almost impossible.

In order for the tool to serve as long as possible and NOT to have such problems, you should first of all read the instruction manual for the trimmer. Also, pay special attention to the engine running time in the trimmer. take a short break every 15 minutes of work and, finally, properly care for the tool, wipe it after work, grease it with graphite grease. Observing such simple rules, you can significantly increase the service life of the tool and it is quite possible that you do NOT have to look for reasons why the gasoline trimmer does not start.

36,952 total views, 4 views today

Starting the lawn mowers for the first time or after a long period of inactivity

a lawn mower differs from a trimmer in that it is NOT a fishing line that acts as a grass cutter, but a mechanical reducer or a winch based on gears, equipped with a knife. The knife drive is much more powerful than the forestry mechanism. a powerful lawn mower is also used when cutting bushes. Both Chinese and European lawn mowers are NOT special when the declared power is real.

To lubricate the gears of the reducer, lithol or grease is used. After checking the gearbox, prepare the motor itself for operation. according to the above instructions. If the start fails, the fault is already in the engine.

How to start a trimmer motor or lawn mowers?

The new trimmer is easy to use in water.

• Check the motor type of the device. Trimmers are equipped with a 2 or 4 stroke motor.
• Buy oil for this type of engine. Gasoline for a trimmer. AI-92/93/98, sold at all gas stations.
• Mix oil with gasoline. Mineral oil is mixed in a ratio of 1: 34 with petrol, synthetics. in a 1: 50 Follow the trimmer manufacturer’s recommendations for oil viscosity (see the label on the flask). All-season oil 5W-30 is used more often. DO NOT use untested car oils.
• Pour a small amount (e.g. 0.5 liters) of the resulting fuel into the tank.
• Close the air damper by sliding the desired lever (see instructions).
• Turn the ignition key (or handle) to the on position. otherwise the trimmer will NOT start. Beginners often make this mistake.
• Pump some fuel into the carburetor. if there is a manual “rocker” with a separate button or lever (see the Instruction). It takes 4-7 clicks.
• Place the trimmer on a level surface.
• Pull on the starter cord carefully until you feel it slow down. Then pull it out sharply, but not completely. Repeat this movement up to 4 more times.
• If the engine does NOT start, open the air damper again, otherwise the candles will flood with gasoline with further movements of the cord. Perform 2-3 attempts to start the engine with an open handbrake.
• If the engine still does not start, close the choke and make a few more attempts to start it.
• After starting the engine, press the throttle lever, engage idle.

Prerequisites

The reason the trimmer fails can be:

• Tank overflow;
• Excessive pumping of fuel into engines equipped with a manual supercharger;
• Wear in the motor of valves, cylinders, injectors, cam followers and other moving parts;
• The tanks are out of gasoline and / or oil;
• Spark plugs out of order;
• Clogged fuel or air filters;
• The valves in the motor are out of alignment or burnt.

How to start a petrol trimmer?

How to start the trimmer correctly is a question that the owners are puzzled with in the event of a device breakdown. And after a successful repair of the trimmer, the owner tries to avoid repeating the same situation.

Adding fuel through the spark plug holes

If the trimmer engine has manual pumping and the device does NOT start, add a little more fuel to the engine itself through the spark plugs. Do the following.

• Check if the fuel level in the tank is sufficient to drain a small amount. It only takes 20 ml.
• Remove the cap from the candle and unscrew it with a candle wrench.
• If a used trimmer plug is dirty, rinse and ignite it. There should not be any deposits on the electrode of the candle. DO NOT damage the ceramic center conductor insulator. In a new trimmer, check the spark plugs for a factory defect.
• Return the spark plug back and check the spark ignition (discharge between the electrodes) when the starter is triggered.
• Remove the candle again. Using a 20 or 50 cc syringe, pour 20 ml of gasoline into the plug hole.
• Insert and fix the candle, set the value of its technological gap at least and not more than a millimeter.
• Prime fuel using the priming button (or lever). if your trimmer model has one. Press the button every 4 seconds.

Now try to start the motor. Close the air damper immediately after starting.

Preventive maintenance of the unit

Any device will serve much longer if you take care of it in a timely manner and prevent the creation of emergency situations. For example, regularly clean the working planes and the area of ​​open parts of the device from dirt. For prevention purposes, it is allowed to cover open cavities when working in dew, dusty bushes or large thickets. This prophylaxis is recommended for a very short time to prevent overheating of the engine due to poor ventilation.

Timely replacement of filters in an internal combustion engine is important. In modern models there are special types of filters that prevent contamination of the fuel system. Inexperienced users do not know about the need to replace filters until problems arise with the operation of the piston system. Replacing filters in due time will save a lot of money from the of a summer resident or owner of a private house.

Be sure to clean the ventilation openings from trapped plant parts and dust, blow through the channels. Do not use metal objects, especially sharp objects, to remove layers. Scratches on the inner surface will lead to accumulation of dirt residues. Cleans from the dust layer and the outer parts of the case.

How to choose a trimmer by engine type?

Lawn mowers on the market today are offered in two types of engine:

• Two-stroke;
• Four-stroke.

Using the trimmer is convenient for all household people who want to keep lawns in the courtyard and adjacent areas in a neat and tidy condition. When buying, the question arises of how to choose the right motorized mower so that the price matches the quality, and you did not have to overpay for the extra engine power.

It is possible to use petrol trimmer in wet and rainy weather, but in accordance with safety requirements, electrical appliances cannot be used in wet conditions. Reviews suggest that gasoline engines differ from electric models with increased power, and make it possible for long-term operation without interruption.

The only advantage of electric mowers is their price, simple low-power models cost half the price of similar petrol trimmers. To ensure order on the lawn in a private house, you should choose gasoline-powered units of low weight and low power. They are equipped with one cutting tool, only for mowing the grass and its occasional mowing.

Four-stroke engines

If we talk about experienced gardeners, then they prefer this particular type of engine. Technical systems and components in such units are much more complicated and they are always repaired in workshops, but these trimmers are distinguished by greater power and the ability to work for a long time at low speeds. Such technical characteristics make it possible to cut not only thin grass, but also old thick grass stems and even some young growth of trees.

Trimmer components

The device of mowers of various modifications cannot be classified as complex mechanisms. The unit includes:

• A pen;
• Barbell;
• Engine;
• Head with installed cutting elements;
• Gasoline tank;
• T-shirt;
• Nozzles.

The attachments are used to increase the functionality of the device, with their use the trimmer is used for snow removal, cultivation, pruning of bushes and young trees.

Two-stroke engines

Gasoline mower units with this type of engine usually have a low price. We will NOT talk about the fundamental difference between the two types of engines from each other in terms of operation, we will only note the difference in maintenance and operation.

The advantage of trimmers on two-stroke engines is that they are small. The engines are unpretentious in relation to the quality of gasoline and have a simple mechanism. This is very important, as it allows inexperienced owners to fix small problems on the spot and DO NOT contact the workshop for various trifles. The owners of household plots consider the power of such units to be quite sufficient for work in everyday farming.

The disadvantage in the operation of a two-stroke engine is that it is necessary to constantly measure the required amount of oil for mixing when refueling gasoline. If this procedure is neglected, then problems in the operation of the piston system will be traced.

Pay attention to the mower bar that you purchase. Most often, telescopic and curved rods work poorly and deteriorate. In this regard, it is better to buy mowers with straight rods, which are more durable in work.

It is irrational to buy a powerful model for preventive cutting of grass near the house, in addition, it should be remembered that each mower is in the hands for a certain period of time and has weight. This suggests that it is necessary to purchase units of low weight and such power, which is necessary in each specific case.

Engine location

The placement of the engine in the unit is important and occurs:

• Top;
• Lower.

Engine on top

Top-mounted engine The most reliable, such units are more powerful. Reviews indicate that buyers choose them. If you choose a model with a two-stroke engine, top-mounted, then such a trimmer will serve faithfully for many years, which is very attractive, but you have to pay a high price for them. Top-mounted design allows the engine to become less clogged from grass and dust residues, significantly extending engine life.

Using a special lubricant

A cavity is provided for placing the lubricant in the gearbox, which is opened with a screw plug, and a portion of the lubricant is placed in the opened hole. It should be said about the composition of the trimmer lubricant, which consists of components that decompose after use and DO NOT bring harmful substances into the surrounding space.

The lubricant is changed after 50-55 hours of operation of the unit, this data can be found in more detail in the technical documents for the trimmer. The shaft of the unit is constantly in need of lubrication. Before starting work, after buying a new mower, be sure to thoroughly lubricate the shaft, if it has not been processed from the factory.

Manufacturers make sure that users of their products save on the purchase of lubricants for various parts of the mechanism and develop a universal version, which provides for interchangeability during maintenance.

How to choose a trimmer by engine type?

Lawn mowers on the market today are offered in two types of engine:

• Two-stroke;
• Four-stroke.

Using a special lubricant

A cavity is provided for placing the lubricant in the gearbox, which is opened with a screw plug, and a portion of the lubricant is placed in the opened hole. It should be said about the composition of the trimmer lubricant, which consists of components that decompose after use and DO NOT bring harmful substances into the surrounding space.

The lubricant is changed after 50-55 hours of operation of the unit, this data can be found in more detail in the technical documents for the trimmer. The shaft of the unit is constantly in need of lubrication. Before starting work, after buying a new mower, be sure to thoroughly lubricate the shaft, if it has not been processed from the factory.

Manufacturers make sure that users of their products save on the purchase of lubricants for various parts of the mechanism and develop a universal version, which provides for interchangeability during maintenance.

Four-stroke engines

If we talk about experienced gardeners, then they prefer this particular type of engine. Technical systems and components in such units are much more complicated and they are always repaired in workshops, but these trimmers are distinguished by greater power and the ability to work for a long time at low speeds. Such technical characteristics make it possible to cut not only thin grass, but also old thick grass stems and even some young growth of trees.

Lower location

These trim tabs have the disadvantage that grass and dirt are constantly clogged in the engine part. Bottom-mounted mowers are not very powerful. Aggregates are usually purchased to periodically maintain an attractive lawn when only thin grass stems are mowed.

Using the trimmer is convenient for all household people who want to keep lawns in the courtyard and adjacent areas in a neat and tidy condition. When buying, the question arises of how to choose the right motorized mower so that the price matches the quality, and you did not have to overpay for the extra engine power.

It is possible to use petrol trimmer in wet and rainy weather, but in accordance with safety requirements, electrical appliances cannot be used in wet conditions. Reviews suggest that gasoline engines differ from electric models with increased power, and make it possible for long-term operation without interruption.

The only advantage of electric mowers is their price, simple low-power models cost half the price of similar petrol trimmers. To ensure order on the lawn in a private house, you should choose gasoline-powered units of low weight and low power. They are equipped with one cutting tool, only for mowing the grass and its occasional mowing.

Trimmer components

The device of mowers of various modifications cannot be classified as complex mechanisms. The unit includes:

• A pen;
• Barbell;
• Engine;
• Head with installed cutting elements;
• Gasoline tank;
• T-shirt;
• Nozzles.

The attachments are used to increase the functionality of the device, with their use the trimmer is used for snow removal, cultivation, pruning of bushes and young trees.

Engine location

The placement of the engine in the unit is important and occurs:

• Top;
• Lower.

Two-stroke engines

Gasoline mower units with this type of engine usually have a low price. We will NOT talk about the fundamental difference between the two types of engines from each other in terms of operation, we will only note the difference in maintenance and operation.

The advantage of trimmers on two-stroke engines is that they are small. The engines are unpretentious in relation to the quality of gasoline and have a simple mechanism. This is very important, as it allows inexperienced owners to fix small problems on the spot and DO NOT contact the workshop for various trifles. The owners of household plots consider the power of such units to be quite sufficient for work in everyday farming.

The disadvantage in the operation of a two-stroke engine is that it is necessary to constantly measure the required amount of oil for mixing when refueling gasoline. If this procedure is neglected, then problems in the operation of the piston system will be traced.

Pay attention to the mower bar that you purchase. Most often, telescopic and curved rods work poorly and deteriorate. In this regard, it is better to buy mowers with straight rods, which are more durable in work.

It is irrational to buy a powerful model for preventive cutting of grass near the house, in addition, it should be remembered that each mower is in the hands for a certain period of time and has weight. This suggests that it is necessary to purchase units of low weight and such power, which is necessary in each specific case.

Preventive maintenance of the unit

Any device will serve much longer if you take care of it in a timely manner and prevent the creation of emergency situations. For example, regularly clean the working planes and the area of ​​open parts of the device from dirt. For prevention purposes, it is allowed to cover open cavities when working in dew, dusty bushes or large thickets. This prophylaxis is recommended for a very short time to prevent overheating of the engine due to poor ventilation.

Timely replacement of filters in an internal combustion engine is important. In modern models there are special types of filters that prevent contamination of the fuel system. Inexperienced users do not know about the need to replace filters until problems arise with the operation of the piston system. Replacing filters in due time will save a lot of money from the of a summer resident or owner of a private house.

Be sure to clean the ventilation openings from trapped plant parts and dust, blow through the channels. Do not use metal objects, especially sharp objects, to remove layers. Scratches on the inner surface will lead to accumulation of dirt residues. Cleans from the dust layer and the outer parts of the case.

Four-stroke engines

If we talk about experienced gardeners, then they prefer this particular type of engine. Technical systems and components in such units are much more complicated and they are always repaired in workshops, but these trimmers are distinguished by greater power and the ability to work for a long time at low speeds. Such technical characteristics make it possible to cut not only thin grass, but also old thick grass stems and even some young growth of trees.

Using a special lubricant

A cavity is provided for placing the lubricant in the gearbox, which is opened with a screw plug, and a portion of the lubricant is placed in the opened hole. It should be said about the composition of the trimmer lubricant, which consists of components that decompose after use and DO NOT bring harmful substances into the surrounding space.

The lubricant is changed after 50-55 hours of operation of the unit, this data can be found in more detail in the technical documents for the trimmer. The shaft of the unit is constantly in need of lubrication. Before starting work, after buying a new mower, be sure to thoroughly lubricate the shaft, if it has not been processed from the factory.

Manufacturers make sure that users of their products save on the purchase of lubricants for various parts of the mechanism and develop a universal version, which provides for interchangeability during maintenance.

Trimmer components

The device of mowers of various modifications cannot be classified as complex mechanisms. The unit includes:

• A pen;
• Barbell;
• Engine;
• Head with installed cutting elements;
• Gasoline tank;
• T-shirt;
• Nozzles.

The attachments are used to increase the functionality of the device, with their use the trimmer is used for snow removal, cultivation, pruning of bushes and young trees.

How to choose a trimmer by engine type?

Lawn mowers on the market today are offered in two types of engine:

• Two-stroke;
• Four-stroke.

Using the trimmer is convenient for all household people who want to keep lawns in the courtyard and adjacent areas in a neat and tidy condition. When buying, the question arises of how to choose the right motorized mower so that the price matches the quality, and you did not have to overpay for the extra engine power.

It is possible to use petrol trimmer in wet and rainy weather, but in accordance with safety requirements, electrical appliances cannot be used in wet conditions. Reviews suggest that gasoline engines differ from electric models with increased power, and make it possible for long-term operation without interruption.

The only advantage of electric mowers is their price, simple low-power models cost half the price of similar petrol trimmers. To ensure order on the lawn in a private house, you should choose gasoline-powered units of low weight and low power. They are equipped with one cutting tool, only for mowing the grass and its occasional mowing.

Two-stroke engines

Gasoline mower units with this type of engine usually have a low price. We will NOT talk about the fundamental difference between the two types of engines from each other in terms of operation, we will only note the difference in maintenance and operation.

The advantage of trimmers on two-stroke engines is that they are small. The engines are unpretentious in relation to the quality of gasoline and have a simple mechanism. This is very important, as it allows inexperienced owners to fix small problems on the spot and DO NOT contact the workshop for various trifles. The owners of household plots consider the power of such units to be quite sufficient for work in everyday farming.

The disadvantage in the operation of a two-stroke engine is that it is necessary to constantly measure the required amount of oil for mixing when refueling gasoline. If this procedure is neglected, then problems in the operation of the piston system will be traced.

Pay attention to the mower bar that you purchase. Most often, telescopic and curved rods work poorly and deteriorate. In this regard, it is better to buy mowers with straight rods, which are more durable in work.

It is irrational to buy a powerful model for preventive cutting of grass near the house, in addition, it should be remembered that each mower is in the hands for a certain period of time and has weight. This suggests that it is necessary to purchase units of low weight and such power, which is necessary in each specific case.

Engine on top

Top-mounted engine The most reliable, such units are more powerful. Reviews indicate that buyers choose them. If you choose a model with a two-stroke engine, top-mounted, then such a trimmer will serve faithfully for many years, which is very attractive, but you have to pay a high price for them. Top-mounted design allows the engine to become less clogged from grass and dust residues, significantly extending engine life.

Equipped with a cutting edge

The controversy in cutting elements has been going on for quite some time. The following are used as cutting elements:

• Fishing line;
• Plastic or steel knife;
• Saw blade;
• Combined option.

The performance of any such device is characterized by the type of cutting part. It can be made in the form of one of the above options, and in some models they combine a fishing line and a knife, which change as needed. The width of the cut strip ranges from 25 to 50 centimeters.

One or another type of cutting element should be chosen depending on the direction of activity. If you are trimming overgrown grass in the backyard or on the lawn in front of the house, then the line will definitely do this job. She will cut thin grass or weeds without any problems, but you will have to fight with thickets of mature Burdocks with knives and saws.

Steel knives and circular saws will easily remove old weeds and fresh tree shoots from the path. The only drawback is that such mowing will require the trimmer to operate at maximum power and, therefore, an increase in material costs for gasoline fuel.

Preventive maintenance of the unit

Any device will serve much longer if you take care of it in a timely manner and prevent the creation of emergency situations. For example, regularly clean the working planes and the area of ​​open parts of the device from dirt. For prevention purposes, it is allowed to cover open cavities when working in dew, dusty bushes or large thickets. This prophylaxis is recommended for a very short time to prevent overheating of the engine due to poor ventilation.

Timely replacement of filters in an internal combustion engine is important. In modern models there are special types of filters that prevent contamination of the fuel system. Inexperienced users do not know about the need to replace filters until problems arise with the operation of the piston system. Replacing filters in due time will save a lot of money from the of a summer resident or owner of a private house.

Be sure to clean the ventilation openings from trapped plant parts and dust, blow through the channels. Do not use metal objects, especially sharp objects, to remove layers. Scratches on the inner surface will lead to accumulation of dirt residues. Cleans from the dust layer and the outer parts of the case.

The lawn mowers candle is heated. How and why he pours a candle on trimmers, lawn mowers

Recently, the gasoline trimmer has acquired the status of one of the main tools in the arsenal of summer residents. And this is not surprising, because a motorized scythe allows you to quickly put your personal plot in order. However, it sometimes happens that the trimmer is even cold. In such situations, you have to independently determine the cause of the malfunction. Let’s figure out what to do if the trimmer won’t start. The reasons that most often lead to such troubles will be discussed below.

Fills the candles on the Stihl trimmer Reasons

The heating of the spark plug is facilitated by the use of heat-resistant engine oils for 4-stroke engines, high wear of the compression rings or the entire piston group as a whole.

UCO Candle Lantern Frequently Asked Questions

Due to duties and taxes, we currently DO NOT offer online sales to consumers in Canada or outside the United States. We are sorry for the inconvenience.

How to enter a UCO promo code to get a discount?
After creating an account.
Login to cart.
Click on the “Modify Cart” link or the “Enter Discount Code” link.

Click the link you see below.
Enter the promo code of the discount.
Just enter your code in the box below. You can only use one code once.

UCO (pronounced “you-co”) provides reliable necessities of warmth, light, and electricity that can be used at home or outdoors.

Replacement candles and glass are available from UCO candlelight retailers including REI and Campmor. We will gladly direct you to your local source if you call us or email us.

Our original Candle Lantern is still the most popular for versatile use such as hiking, camping and home use, Our Micro Candle Lantern is best for light hiking. The Candlelier Candle Lantern is best for car camping, at home and on the patio (including in emergencies and power outages), and for large groups on hiking and winter camping. Mini Candle Lantern is ideal for efficient home use and atmosphere creation.

UCO candle lights provide hours of warm, reliable light. There are batteries that you can discharge and throw away, there are bulbs that can burn out, and there are no switches that can fail. Candle lights work very well in cold conditions when rechargeable lights quickly fail. Candle lanterns generate a lot of heat, which helps to reduce moisture condensation during winter hiking.

Excess or spilled wax can be removed from the flashlight by chipping it off or scraping it off with a blunt object. It will be easier if you first place the waxed part in the freezer for 10-20 minutes, until the wax is already brittle. You can also remove the wax by heating it until it is hot enough to melt and blot with absorbent material.

Candle lanterns work silently, unlike gas and propane lanterns, which are usually quite loud. The warm golden flame of a candle lantern is much more pleasing to the eye than the harsh white robes of gas and propane lanterns. Our candle lanterns provide enough light with 3 candles to light a large tent or camping.

Yes, as long as you follow our directions and keep them away from flammable materials. The closed structure protects the flame from direct contact with other materials and the handle keeps the lantern at a safe distance under the eaves when hanging in the tent. DO NOT touch the heat shields while the flashlight is on or until it cools down after use. Never leave a burning candle unattended.

UCO manufactures many private label versions of our Candle Lantern, including REI, L.L. Bean, E.M.S. Among other things. You can identify the UCO candlelight by its unique spring loaded candle tube and body. The name UCO comes from all the Candle Lanterns produced by UCO.

Unfortunately, we have discontinued oil inserts for our candle lanterns, but we are working on a replacement that will use liquid fuel in the candle lantern.

Some reasons

It often happens that users of this kind of machines are trying to “save money”, pouring into the tank NOT fuel with the usual octane number, but something incomprehensible that has been in a plastic Canister for almost a dozen years.

Why Are Candles Burning On Trimmers

What to do when the petrol trimmers DO NOT start?

The gasoline trimmer is a surprisingly necessary tool with which you can mow Not only a small clearing in front of the house, but also a whole large lawn. Unfortunately, there is nothing endless in this world, and therefore you may be faced with the fact that petrol trimmers DO NOT start.

Fills candles on the Champion trimmer What to do EVDIRAL.RU

A spark plug is an integral part of any internal combustion engine, providing the energy required to ignite the fuel. If it is corroded, dirty, frayed or otherwise damaged, the engine or engine will NOT operate poorly. A poor Stihl chain saw motor can mean more work for the operator and can be dangerous. Therefore Stihl recommends replacing the spark plug every 100 hours.

Required tools:. Diagnostics of the candle channel

What to do if the used fuel mixture is in good order, but still The reasons for the failure of the mechanism may lie in excessive wetting of the spark plug channel. To diagnose and fix the problem, you must do the following:

• Unscrew the candle. Wipe it thoroughly and then dry it.
• Drain excess fuel in the chamber through the appropriate plug hole.
• Clean the old plug if there is carbon deposits on its surface. To cope with the task will allow the use of an ordinary ladies’ nail file or a file.
• When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the gap.
• Assemble the functional block back.
• Try to start the trimmer.

It is recommended to dry the candle channel for at least half an hour. However, in no case should you resort to calcining its elements. After all, heating the spark plug can lead to its final damage. What to do if the maintenance of the functional unit was carried out in accordance with the above recommendations, but the trimmer does not start, there is a spark? In this case, it is worth treating the threaded connection with gasoline. The latter does not need to be abundantly impregnated with fuel. It should only be slightly damp. Resorting to such actions should be taken to ensure ignition. After all, no matter how strong the spark the candle gives, there will simply be nothing to ignite in an absolutely dry chamber.

If even in this case the trimmer does not start, it is worth assessing the quality of the contact between the high-voltage wire and the candle. In the absence of a spark (if there is a reliable connection between the indicated elements), the problem is most likely caused by a breakdown of the ignition unit. In this situation, you will have to turn to the services of the wizards who will reinstall the node.

It often happens that users of this kind of machines are trying to “save money”, pouring into the tank NOT fuel with the usual octane number, but something incomprehensible that has been in a plastic Canister for almost a dozen years.