Huter benzotrimmer proportions of oil and gasoline. Fuel mixture preparation rules

The ratio of gasoline and oil for a trimmer for Huter grass

First of all, it is necessary to take into account the information that the manufacturer recommends, since in the case of failure of the motorcycles, you can make your claims to him, and not a third.party source. If there is no instructions in the passport, and even more so if the passport is missing, then we recommend looking for another trimmer model for grass at a more reliable seller.

For all other cases when you have a lawn mower model in your hands and there is no way to find out its technical features, there are standard proportions of the most likely components of the fuel mixture for a two.stroke engine. Basically, these units use AI-92 gasoline and special synthetic oil, which contains a solvent for better mixing with fuel. Such oil evaporates slowly and has the ability to completely burn in the cylinder, without leaving a car.

The standard attitude of synthetic oil to gasoline is 1: 50. This means that 100 ml of oil needs 5 liters of gasoline, and in accordance with this, oil consumption per 1 liter of gasoline is 20 ml. Knowing the amount of oil required to dilute 1 liter of fuel, you can easily calculate any norms when preparing fuel for a trimmer for grass. When using mineral oils, the ratio of 1: 40 is most often standard. Therefore, 1 liter of fuel will require 25 ml of such oil, and 125 ml per 5-liter canister.

When the lawn mower is working, it will not be difficult to determine and adjust the actual amount of oil, the right of a particular model, who has a little experience in the operation of such a technique

You should only pay attention to exhaust gases (their color, toxicity of the smell), stability of the cycles, engine heating and developed power. about what consequences from the incorrect proportions of mixing gasoline and oil can be expected is lit in another section of the article

There are motorcycles operating on gasoline AI-95 brand gasoline. It should also be taken into account.

If the manufacturer recommends fuel with such an octane number, then you need to follow the requirements so as not to reduce the working resource of technology.

How much to add oil? In what proportions to breed with gasoline? How much should be poured per 1 liter of gasoline?

Lawn mowers are a fairly common equipment for combating weed vegetation in summer cottages, in personal, road and housing and communal services. These devices have two more items. a trimmer for grass and a lawn mower. These units differ in their engines. expensive of them have four.stroke engines, all others are two.stroke. Naturally, the latter are more popular in the middle of the population, because it is easier in design and by mass easier and significantly cheaper than their own four.stroke rivals. But two.stroke models are inconvenient because the fuel mixture for them must be prepared manually, withstanding a strict dose between gasoline and oil. In four.stroke analogues, the mixing of these components occurs automatically, only the gas tank and oil tank should be filled with proper substances. Let’s see the question of the correctness of the refueling of specifically two.stroke motorcycle, because it depends on how effective and long will be the work of such an unit.

Specifications

Before making a choice in the direction of a particular model of equipment, you must familiarize yourself with its technical characteristics. The Huter GGT 2500S model is no exception, the operating instructions of which are presented below. This unit is a device whose power reaches 3.3 liters. With., or 2.5 kW.

As a cutting tool, a knife or fishing line for a trimmer is used (by choice). The design has a bicycle handle and a hard drive shaft. Speasing width is 25.5 cm. When consumers consider this Huter lawn mower, they pay special attention to the spindle rotation frequency. In this case, it is 9500 per minute. The landing diameter is 25.4 mm. You may also be interested in the level of noise, which is 96 dB. Weighs the unit 7 kg. The thickness of the used fishing line is 2.4 mm.

How to refuel a trimmer for grass

The finished mixture of gasoline with butter can be stored for no more than 3 months (clean gasoline is stored less). Dilute the fuel in the quantity that is enough for several applications of the trimmer for the grass. In general, prepare:

• gasoline and oil, which is suitable for two.stroke engines with an air cooling system;
• metal canister and a mixture container;
• respirator;
• gloves.
• Pour 1 l of gasoline into a suitable volume of 1 l of gasoline and add 1/2 of the desired amount of oil.
• Mix carefully, being at a decent distance from the sources of open fire.
• Add the rest of the oil to combustible and mix everything again.

General recommendations for refueling a trimmer for grass with a two-or four-stroke engine:

• Place the fuel tank so that the lid is located on top, and then pour the required amount of fuel.
• Do not overfill the fuel tank. This will lead to one of the problems: transferring into the intake pipe and fuel filter, flammable ignition or breakdown of the motor.
• Try to fill the mixture so that it does not spill. To do this, you can use the watering can.
• If you still poured fuel, then immediately wipe it. Put the wiping material, do not accumulate indoors. this is fire hazardous.
• The launch of the device should begin after the canister with fuel is removed at a distance of more than 10 m.
• If there was a long break between the operations of the mowing, then the remaining old fuel be sure to drain.

Standard proportions

First of all, it is necessary to take into account the information that the manufacturer recommends, since in the case of failure of the motorcycles, you can make your claims to him, and not a third.party source. If there is no instructions in the passport, and even more so if the passport is missing, then we recommend looking for another trimmer model for grass at a more reliable seller.

Overview of a gasoline trimmer for Huter GGT 1900t grass

For all other cases when you have a lawn mower model in your hands and there is no way to find out its technical features, there are standard proportions of the most likely components of the fuel mixture for a two.stroke engine. Basically, these units use AI-92 gasoline and special synthetic oil, which contains a solvent for better mixing with fuel. Such oil evaporates slowly and has the ability to completely burn in the cylinder, without leaving a car.

The standard attitude of synthetic oil to gasoline is 1: 50. This means that 100 ml of oil needs 5 liters of gasoline, and in accordance with this, oil consumption per 1 liter of gasoline is 20 ml. Knowing the amount of oil required to dilute 1 liter of fuel, you can easily calculate any norms when preparing fuel for a trimmer for grass. When using mineral oils, the ratio of 1: 40 is most often standard. Therefore, 1 liter of fuel will require 25 ml of such oil, and 125 ml per 5-liter canister.

When the lawn mower is working, it will not be difficult to determine and adjust the actual amount of oil, the right of a particular model, who has a little experience in the operation of such a technique. You should only pay attention to exhaust gases (their color, toxicity of the smell), stability of the cycles, engine heating and developed power. about what consequences from the incorrect proportions of mixing gasoline and oil can be expected is lit in another section of the article. There are motorcycles operating on gasoline AI-95 brand gasoline. It should also be taken into account.

If the manufacturer recommends fuel with such an octane number, then you need to follow the requirements so as not to reduce the working resource of technology.

The selection of oil and gasoline for the preparation of fuel mixture for a trimmer for grass

Trimmer for grass, or lawn mower. a tool that cannot be dispensed with in the household. over, its reliability, efficiency and long life depend on many factors. For example, fuel quality. This means that you need to correctly select oil for a trimmer for grass, observe the proportions when adding to gasoline and the rules for refueling the device.

The working resource of the engine of motorcosa depends on how accurately you will observe the proportion of the oil-Benzos mixture. The fact is that the fuel mixture enters the cylinders in the form of gasoline-oil fog. And the task of the oil composition is the lubrication of moving and rubbing parts and surfaces of various details located in the cylinder. If it suddenly turns out that the oils are not enough, and somewhere it will not be enough, the details in contact with dry ones will begin to damage each other. As a result, scuffs, scratches and chips are formed, which will necessarily lead to complete or partial indifference of the engine (for example, it can jam it).

In the opposite case, when too many oils enter the engine, it does not have time to completely burn, settling on the walls of the cylinder and turning over time into solid particles. coke, slag and the like. As you can guess, this also leads to the failure of the engine. The most important thing is that you cannot allow. even a single violation of the proportion towards the lack of oil. It is better to pour a little oil 10 times than only 1 time do not add. It often happens that this time is quite enough to break the engine.

The selection of oil and gasoline for the preparation of fuel mixture for a trimmer for grass

Trimmer for grass, or lawn mower. a tool that cannot be dispensed with in the household. over, its reliability, efficiency and long life depend on many factors. For example, fuel quality. This means that you need to correctly select oil for a trimmer for grass, observe the proportions when adding to gasoline and the rules for refueling the device.

The working resource of the engine of motorcosa depends on how accurately you will observe the proportion of the oil-Benzos mixture. The fact is that the fuel mixture enters the cylinders in the form of gasoline-oil fog. And the task of the oil composition is the lubrication of moving and rubbing parts and surfaces of various details located in the cylinder. If suddenly it turns out that the oils are not enough, and somewhere it will not be enough, the details in contact with dry ones will begin to damage each other. As a result, scuffs, scratches and chips are formed, which will necessarily lead to complete or partial indifference of the engine (for example, it can jam it).

In the opposite case, when too many oils enter the engine, it does not have time to completely burn, settling on the walls of the cylinder and turning over time into solid particles. coke, slag and the like. As you can guess, this also leads to the failure of the engine. The most important thing is that you cannot allow. even a single violation of the proportion towards the lack of oil. It is better to pour a little oil 10 times than only 1 time do not add. It often happens that this time is quite enough to break the engine.

How to breed gasoline for a trimmer for grass

Depending on the variety of trimmers, they can be seasoned with a fuel mixture or separately gasoline and oil. Now there is a huge variety of types of motor oils that are suitable for different technology, including garden. To choose the right fuel for a certain model of motorcycles, you need to know its technical features and understand the brands of gasoline, as well as liquid lubricants. All the details on how to dilute gasoline with oil for a trimmer for grass is in the material further.

The finished mixture of gasoline with butter can be stored for no more than 3 months (clean gasoline is stored less). Dilute the fuel in the quantity that is enough for several applications of the trimmer for the grass. In general, prepare:

• gasoline and oil, which is suitable for two.stroke engines with an air cooling system;
• metal canister and a mixture container;
• respirator;
• gloves.
• Pour 1 l of gasoline into a suitable volume of 1 l of gasoline and add 1/2 of the desired amount of oil.
• Mix carefully, being at a decent distance from the sources of open fire.
• Add the rest of the oil to combustible and mix everything again.

General recommendations for refueling a trimmer for grass with a two-or four-stroke engine:

• Place the fuel tank so that the lid is located on top, and then pour the required amount of fuel.
• Do not overfill the fuel tank. This will lead to one of the problems: transferring into the intake pipe and fuel filter, flammable ignition or breakdown of the motor.
• Try to fill the mixture so that it does not spill. To do this, you can use the watering can.
• If you still poured fuel, then immediately wipe it. Put the wiping material, do not accumulate indoors. this is fire hazardous.
• The launch of the device should begin after the canister with fuel is removed at a distance of more than 10 m.
• If there was a long break between the operations of the mowing, then the remaining old fuel be sure to drain.

How to dilute gasoline with oil for a trimmer for grass

Dilute gasoline for a trimmer for grass in the correct proportion. Insufficient oil can lead to poor lubrication of the elements of the lawn mower, which contributes to rapid wear. In case the oil is more than the olive formed on the pistons and spark plugs. Foreths on the moving parts of the engine interferes with normal operation and leads to the speedy breakdown of the motor.

What proportion is required for a specific model of a trimmer for grass can be found from the attached instructions. Most often, for 2-stroke gasoline motors of motorcycles, the fuel mixture is used in a ratio of 50: 1, where 50 is part of the gasoline, 1-part of the oil. That is, 20 ml of oil should be added to 1 liter of gasoline. The table will help to choose the necessary ratio.

To correctly measure the proportions, use measured containers with a milliliter scale. For these purposes, a special canister with a double neck is perfect, it is designed to mix and storage of oilbenzin. For example, oil can be typed with a medical syringe without a needle. Before mixing liquids, make sure that there is no water, dust and particles of dirt in the container for the finished fuel mixture.

Diluting gasoline with lubricating fluid directly in the fuel tank is unacceptable, in addition, the proportion of oil and gasoline should be clearly observed. If you ignore this rule, then the operation of a trimmer engine for grass can be unstable, which is why it will quickly fail.

It is not recommended to use plastic bottles or canists for this purpose. This is due to the fact that gasoline has the ability to dissolve plastic, which means that part of the plastic can get into the fuel tank, which can lead to a carburetor breakdown. Although there are special plastic canists with the marking “Flame”.

• petrol;
• oil suitable for two.stroke engines with an air cooling system;
• canister, better metal;
• Mixing container is also better metal;
• gloves;
• respirator.

In addition to protective equipment, do not forget about fire safety rules, because gasoline and engine oil are easily ignited:

• It is better to work on the street to avoid accumulation of gasoline vapor in the room;
• you can not smoke and create situations related to the emergence of a spark.

Make a mixture of gasoline and oil as follows:

Pour 1 liter of gasoline into the container, add half the desired portion of the oil

Mix thoroughly, do it extremely carefully away from the sources of open fire. Add the rest of the oil to gas for the grass and mix thoroughly again. Now fuel can be poured into the fuel tank of a trimmer for grass.

The mixture can be stored for no more than three months, so it is better to dilute gasoline in such quantities that there is enough use.

For dilution, only high.quality oil can be used, while it is recommended to purchase it only in trusted stores, for example in specialized hypermarkets.

What gasoline to fill in a trimmer for grass. What gasoline can be poured into a trimmer for grass?

Before finding what gasoline can be poured into a trimmer for grass, you need to determine some concepts used.

• Trammers for grass can be with four.stroke or two.stroke engines. Four.stroke trimmers for grass are more massive and complex in design, lubrication of the details of its motor is carried out due to the oil pump. The engine works on clean gasoline. For two.stroke units. more ordinary ones. the manufacture of fuel consistency consisting of gasoline and oil is required. Here is due to the amount of oil that is in combustible, and the rubbing parts in the cylinder of this motor are lubricated.
• For the manufacture of consistency, gasoline of a certain AI-95 or AI-92 brand is needed. The brand of gasoline is located depending on its ignition rate. the octane number. The lower this indicator, the more freaks burning gasoline and its larger consumption.

Many models of benzos have two-stroke engines that work to a greater extent on AI-92 gasoline. Fuel for them must be connected without the help of others. It is better to pour gasoline of the brand that is determined for it by the manufacturer, another trimmer for the grass will be out of order. For example, with gasoline of the AI-95 brand, the engine will rapidly overshadowed, and when choosing AI-80, the fuel mixture comes out completely low, because the work of the motor will be unstable and with low power.

In addition to choosing a brand of gasoline, in the manufacture of fuel shift for motorcycles, it is necessary to use a special oil designed specifically for two.stroke engines. Semi.synthetic and synthetic oils are perfect for benzos. Semi.synthetic oils are in the average price spectrum, suitable for such technology from at least some manufacturer, lubricate the necessary elements of the motor well. Synthetic oils are more expensive, but when using them, the engine will work longer. In any case, when buying equipment, you should closely familiarize yourself with the annotation, because from time to time the manufacturer gives advice on the use of certain brands of oil.

Review: trimmer for grass gasoline (lawn mower) Huter GGT-2500T. A very powerful device, I, of course, is glad to him

A Chinese.made lawn mower, which I used for 5 years, became unusable: the engine jammed. I decided to buy a new one, because I didn’t see any sense in the repair. So, having bought the second benzotrimer, there is something to compare with.

Before buying, I collected information on the Internet. At first I wanted to buy an electric trimmer for the grass, but most of them are low.power, and people complain: either they often break, then the bar is short and you have to mow on the vnacolon. Therefore, I decided to still dwell on a gasoline spit.

One Internet specialist said that all the power indicators that are written in the operating manuals of Chinese gas is an empty phrase. You only need to focus on the volume of the engine. If it is more than 40 cubic meters. cm, a braid for grass will cope with grass without problems. With this thought, I went to the store.

The choice was huge, but for the money at that time I was constrained, so there were only 8 thousand in my Having examined motorcycles within 7 thousand, I stopped on the Huter GGT-2500T benzotrimer model. Outwardly the unit made the impression of a good machine, powerful and productive.

Asked the seller to operate. He dumbfounded me with his answer: “It is in the box, and the boxes are in the warehouse. Yes, all this information on the Internet is. You can see at home “. I began to slowly pour anger: “That is, you are now inviting me to go home, sit down for a computer and find the technical characteristics of this trimmer for grass on the Internet?!»The seller, seeing my condition, went back:“ What specific parameters are you interested in?”I replied:” Only engine volume “.

The seller left for the computer and literally anticipated a minute later: “51 cubes”. I did not need anything else. Said that I take. The seller began to take off the braid from the rack, pushed and recommended that I immediately buy another head so that there were no problems with a regular one. I asked what problems. It turned out that the body of the standard head is made of low.quality plastic, which is cooked.

I remembered the old braid. Indeed, that was what it was. For the second season, pieces of plastic began to bounce off the body. There was another head that differs even in appearance, but I decided to work first until the end. It is possible that this ruined the braid. At the first hayfield, another piece of plastic flew off this season, and the head figured it out right in the process of work. The lid, coil, fishing line for a trimmer, washers flew Okay, not in the head, the casing protected.

I drowned a trimmer for the grass, put another beautiful head, started. The engine worked for 5 seconds and stalled. It seemed strange to me. Stall “on hot”? This was not there, if the gasoline did not end, but then it was still half a bacon. I tried to get a braid again, but the starter cord did not get out.

The next day I took off the starter, confident that the matter is in it, but not. The starter worked separately like the Swiss watches. The mood deteriorated. I realized that the engine was jammed. I tried to spin the crankshaft. it doesn’t go.

Perhaps just a coincidence, and perhaps the scattered reel somehow influenced the malfunction of the engine.

So I got a new Huter GGT-2500T benzotrimmer. In a special room, the seller checked his work. I asked to hold on to the handle. There is vibration, like all Chinese motorcycles, but within the norm. And for the Old 2 years, the vibration has become such that three knitted gloves had to be worn, otherwise the hands fell off. I already began to look for the cause of vibration (cold gearbox, the bar, too, means the matter is in the motor), but then the engine jammed.

While the seller was packing the braid, I went to the checkout. Trimmer for the grass along with a new head cost me 8300, so along the way I had to fumble a trifle along my s. I barely scrape. But the cashier made me a discount, and I paid only 7500. After a couple of days he decided to slowly collect a trimmer for the grass. After the store in my hands, I had 2 parts: a box of dense cardboard with a engine and all causals.

And the bar. By the way, she, unlike the old braid, is indifferent. I think it’s a plus. Firstly, it is tougher, and secondly, the fewer the compounds, the lower the risk of breakdown.

I took out the most severe part of the lawn mower with the engine and control handle from the box, on which the red tooth-turning switches of the ignition and the yellow gas key are located. There is also a button-stop that fixes the key in the “full gas” position so that the finger does not get tired of constantly holding the key pressed. Looking ahead, I will say that this button turned out to be motionless. This is not fundamentally for me. I’m not 8 hours every day, but 3 times per season and only on my site. The picture is clearly visible white gas tank below with a cork and a starter with the inscription Huter.

This is what the engine from the clutch looks like. Here I fasten the bar.

And here is the new head, which I immediately fastened to the gearbox, while the bar is separate.

Then he began to consider causals. The operating manual says that the trimmer for grass is equipped with a shoulder belt. But in fact, he turned out to be a resident. The old braid for the grass “harvest” was the same, and she was pretty tired of me. The belts were constantly weakened, unleashed, cut the body, the carbine unfastened with difficulty. But this “harness” was better. The belts turned out to be wider, after adjustment they did not stretch, but I still sewed them immediately, fixing in one position. The first belt was very tough, even with a thimble I had to tinker, piercing it with a needle. But the rest turned out to be surprisingly soft, so the work did the work quickly. The carbine turned out to be more than the old, it is easily unfastened.

An important feature

Prepared a combustible mixture for a trimmer for grass, falls into the combustion chamber of the cylinder in the form of a whitish fog. Oil liquid integrated into gasoline lubricates the crankshaft, cylinder walls. Infoliasis of oil fluid in the fuel is fraught with premature wear of the parts and nodes of a trimmer for grass. Exceeding the norm leads to a breeder that settles on working details, which is also fraught with premature technical wear of motorcycles.

The gasoline mower will serve the owner for a long time, provided that in the fuel tank, they will not be any kind of gasoline, but high.quality prepared fuel.

Oil change

Oil replacement in the lawn mower is carried out once a year, provided that the equipment puts the lawn in order only in the summer. The right time is before the start of the season. It is necessary to replace the oil if in the midst of summer it changed color to black. It is also recommended to change the lubricant after running in the technique, that is, after 3-5 hours of work since the first launch.

For the convenience of consumers, manufacturers of garden equipment offer special for replacing an oil product. The set includes several items:

Before changing the old oil, the mower is turned for 10 minutes. Warm oil merges easier, it also removes along with impurities and garbage. After they are waiting for the technique to cool down

It is important to disconnect the spark plug and drain gasoline. Further, using a pump or syringe, a lubricant is pumped out

Some models have a cork through which fluid remains come out

It is located in the lower part of the case. It is necessary to completely remove the worked out product. If the owner saw the oil in the air mowing filter, then during the replacement of the lubricant, the filter is cleaned and the filter. Fresh oil shimmers through the neck with the help of a funnel into the crankcase. The fluid level is checked by the probe. Usually, to fill the oil container, 0.5 liters of material are enough.

Figure out how to refuel a lawn mower, what kind of oil and fuel to buy, it is easy. In general, it takes about half an hour to replace the lubricant. For the preparation of the fuel mixture and refueling the time of time, it takes even less.

The lawn mower is a useful technique for mowing grass, if it is necessary to constantly care for lawns, park areas. With its help, you can give a well.groomed look to herbal cover much faster than when using a hand braid for grass. The most common gasoline units are. So that they have been served without repair for a long time, they need to be carried out Regular maintenance. One of the mandatory periodic procedures is the replacement of the oil. Depending on the device of the internal combustion engine, it is required to use pure fuel or make a special mixture. The choice of suitable oil and gasoline for the lawn mower is of great importance, since the time of the motor service time directly depends on the quality of fuel and lubricants.

Double.stroke and four.stroke internal combustion engines are installed on gasoline lawnmands. The movement of knives is provided by the energy transmitted by it from the ICE. It occurs due to the expansion of the gases formed during the explosion of gasoline or the fuel mixture in the combustion chamber. In this case, the compression of the gases is provided by the movement of the piston.

For the system to work well, there must exist between the conjugated details The minimum necessary gaps. If their dimensions increase due to wear of the working parts, this leads to a deterioration in the work of the motor unit, and over time and to the complete impossibility of starting it into work. The problem is due to the fact that the required pressure value for fire mixed with atmospheric air is not achieved.

Motor oil covers the parts of the engine with a thin film, this slows down their wear, and the appearance of cutters on the metal surface of mating structural elements is also prevented. This is the main role of oil in the gasoline drive mechanism of the lawn mower.

In addition to reducing friction between the interacting details of the internal combustion engine, the use of oil allows:

• Provide more High.quality cooling drive unit during operation, improving the heat exchange processes between metal and atmospheric air;
• perform work by operating the motor at maximum speeds, which increases labor efficiency and leads to a decrease in time costs;
• protect the metal mechanism from corrosion During winter downtime.

High.quality oils reduce the negative effects of elevated temperature on motor parts. Removing heat, they increase the operating time of the unit before overheating.

Motor oil is a special material that provides non.waste operation of the internal combustion engine, as well as other systems in the lawn mower. Neglect of its quality leads to various breakdowns of the unit.

What kind of oil can gasoline for a chainsaw can be diluted?

Exclusively motor oil for two.stroke engines is added to fuel for chainsaws. Oils for four.stroke engines are categorically not suitable. The reason is that in two.stroke ICE, the oil burns together with gasoline.

In car and other four.stroke ICE, it is poured into the crankcase, has many special additives, it is not initially designed to combat. If it is poured into a chainsaw, it will smoke, will not burn out completely and quickly form a thick layer of carbon monoxide, which in the end can disable the chainsaw.

In addition to the general specification “for two.stroke engines”, the manufacturer of the chainsaws may recommend using on their model oil of a particular brand. It can have special combustible additives and additives extending the service life of the ICE saw.

This is what oil for 2-stroke engines of chainsaws from the famous Champion brand looks like

In the old two.stroke engines of the Soviet period, motor oil was also used, as in four.stroke, for example M8. Old motor oils did not contain such a number of fireproof additives as modern. So that such non.specialized oil provides sufficient lubrication of chainsaws, increased dosages were used.

When running the engine, 1:20 proportion was used, after 1:25. Large quantities of universal oil, not created under complete burnout, led to rapid hair toxing and sticking piston rings, the formation of a carbon on the upper part of the piston, light of the ignition, in the exhaust windows of the cylinder and a silencer. For the same reason, a spark on a chainsaw candle may disappear.

In advanced cases, windows and muffler could be completely tightened by the car. The thick layer of the carbon on the piston significantly reduced the volume of the combustion chamber.

At the same time, the engine remains clean for a long time and serves for a long time, despite the lower supply of mechanical strength in modern ICE in comparison with the old.

We also recommend reading an interesting article about which oil to use for the chain of the chainsaw and how it can be painlessly replaced.

How to use a trimmer correctly?

After the launch of motorcycles, its owner begins the direct operation of the garden tool. If the trimmer for the grass was recently bought, and its owner only begins to run the new model, then the operator should adhere to a number of important rules.

• You do not need to use a trimmer for grass in high speeds of its engine. during the run.in the motor parts should be worn out to each other. If you do not let them do this, then this can lead to a complex breakdown of the engine CPH;
• It is necessary to constantly monitor the temperature of the motor. If the ICE cylinder is too heated, then the operator must stop operating motorcycles and give it to the motor time to cool down.

On average, on average, it takes no more than 1 hour. During this time, one full fuel tank should be consumed. After that, you need to pour a new fuel mixture and continue to use the tool.

During operation, the motorcycles, its owner must adhere to safety regulations. To protect yourself, the operator needs to wear protective glasses, a special suit made of dense fabric and solid shoes with an anti.slip sole. If a trimmer for grass with a powerful engine is used to mow grass, then its owner should wear protective headphones.

There are a number of other rules that the owner of the motorcycle.

• The operator must regularly change the lubrication of the gearbox Motokosa. This must be done at the beginning of each season. If the lawn mower is stored in a cold household room, then before sending the tool gearbox, you need to disassemble and completely clean from lubrication;
• The owner of a braid for grass should use only high.quality brand fuel not lower than indicated in the instructions for the operation of a trimmer for grass. The gasoline used must be mixed with motor oil in the proportion indicated in the manual;
• With intensive operation of the tool, its owner must regularly clean the cylinder and carburetor;
• In order to prevent breakdown of motorcycles, the operator must regularly clean its fuel and air filters. To do this, the elements need to be removed from the trimmer for grass, rinse them with clean gasoline and let them dry;
• If the tool is regularly used in areas with a large number of weeds and wild shrubs, then its owner must monitor the level of sharpening of cutting knives. If they are not sharp enough, then they will need to be sharpened using special devices for this;
• Store motorcycles only in a warm and dry room. This will prevent corrosion of the bar and other metal elements of the tool.

When using motorcycles, it is extremely important to prevent its falls to the ground. To do this, you need to constantly monitor the fixation of the shoulder belt, which is supplied with the tool

We deal with the choice of gasoline for the AI-92 or AI-95 lawn mower

How many people, so many opinions, which applies not only to the choice of oil for a trimmer for grass, but also gasoline. Similarly, in order not to make a mistake with the choice, it is recommended to use gasoline of the brand that the manufacturer recommends (indicated in the manual to the tool). However, not everything is so simple here, since at each gas station of the gasoline brand they are only called the same, but have a completely different composition. It is required to figure it out, and come to a single conclusion about which brand it is better to pour gasoline into a two.stroke engine for your trimmer for grass.

Manufacturers recommend using A-92 gasoline for their technique, and some models require the use of the A-95 brand that do not contain ethyl alcohol. It is not recommended to use gasoline of the AI-90 brand and below, as they will entail the rapid wear of engine parts. Buying gasoline of one brand, one cannot be 100% sure that it is true. The result is the following picture:

• The manufacturer recommends pouring fuel into a trimmer for the grass of the AI-92 brand
• The summer resident uses only gasoline of this brand, but buys it at gas stations, where the price is lower or where you have to
• This negatively affects the internal details of the motor, since at one gas station it is really high-quality AI-92 gasoline, and at the second, at best, if it is AI-80, not AI-76

As a result, the engine suffers, and after a couple of years of operation a new trimmer for the grass, it is necessary. In order not to analyze the quality of fuel or buy only expensive gasoline, it is recommended to refuel only at one gas station. At gas stations, gasoline is poured only into metal canists, not plastic.

There are manufacturers that produce special cleaned fuel for two.stroke engines. If this option is selected, then you will not need to choose the best gas station, a brand of gasoline and control its storage periods.