Motokosa holder on the wall with your own hands. Nazadka for a trimmer for grass aerator lawn

trimmer for grass in the garage how to hang

Hi all! I was faced with such a problem, I have nowhere to attach a lawn mower in the garage, and I don’t want to drag it to the attic because I use it just every 2-3 months, and now I want such an ideas that I want to share with you. Necessary details:-2 rails 1 m long-1 self-tapping screw 25-35 cm long-10 screws 3.5x45mm and.

To store the lawn mower on the wall, a suspension of two metal plates was made, about 50 cm long. Each. The lawn mower lay on the floor and specifically on the “place” of the strip bent. The stripes are connected by a bolt. The suspension itself is fixed on the wall with two anchor bolts. On the upper ends of the stripes were worn by tubes, the ends of which were pulled away by exhaust rivets through the washers. Two pieces cut for putting on a rubber hose and wrapped with island are installed on the handle of the lawn mower. A rubber plate is fixed on the wall to prevent damage to the gas mowing tank against the wall.

How to store a benzotrimer

I was faced with such a problem, I have nowhere to attach a lawn mower in the garage, and I don’t want to drag it to the attic because I use it just every 2-3 months, and now I want such an ideas that I want to share with you. Necessary details:-2 rails 1 m long-1 self-tapping screw 25-35 cm long-10 self-tapping screws 3.5x45mm and I have a stupid chain with hooks to the ceiling and everything. Brought, hanged and let it hangs. And so, too. 7.

Place for a trimmer’s lawmaker for grass

Hi all!I was faced with such a problem, I have nowhere to attach a lawn mower in the garage, and I don’t want to drag it to the attic because I use it just every 2-3 months, and now I want such an ideas that I want to share with you.Necessary details:-2 rails 1 m long-1 self-tapping screw 25-35 cm long-10 screws 3.5x45mmy wish for good luck!

Комментарии и мнения владельцев 32

Log in or register to write Комментарии и мнения владельцев, ask questions and participate in the discussion.

The case would have to be put on it, otherwise it will gather dust in the offseason

I have gasoline in a spit all winter. of course, I can, of course, can win 300 but in the spring and there are no problems. if he remained not to merge him? This is already waste.And the idea of ​​a cool one must also attach such a type of one, otherwise it is also lying around. though I have a collapsible but still interferes in the garage.

Boiled.I opened the link because it became interesting how to store a trimmer for the grass. It turns out it’s just a shelf under the ceiling.I have a wooden staircase. I rarely use it. For storage, I made two hooks under the ceiling. I wonder how I keep the stairs?For storing trash, I built a rack from the boards along the wall.Когда хлама стало больше, вдоль второй стенки Соорудил стеллаж из стоечного профиля 50. I put the trash in the boxes, on the floor are severity. Someone is interested in how I keep the rubbish and my ‘make’? I don’t think.Or the washer tank 2108, which I pinned to the garage gate and my hands.

I expect in the near future a detailed post about a self.tapping screw on which you can hold a working robe or keys. I urge everyone to lay out real crafts that really help out.

I also have the 25th Olechka, I recently bought.And you can hang horizontally? VVS-Razan. View profile. User messages. Private message. Registration: 06.09.2007 Ryazan Posts: 1130. It may be possible, but with another suspension design.

But the whole question is that gasoline does not flow.

Homemade nozzle on a trimmer for grass instead of plastic coil

To make the nozzle, the author uses a protective casing from a car rack. You will also need a metal washer and an ordinary hexagonal nut (but only with left thread).

We recommend that you read the article: “2 useful tools that can be made from taps”. The tools are designed to work with metal and are definitely useful in a home workshop.

For work, you will need a welding machine and an electric drill, with which in the nozzle itself it will be necessary to drill holes for a fishing line for a trimmer. In time, all work will take no more than 15-20 minutes.

The process of manufacturing the nozzle for a trimmer for grass

First of all, it is necessary to clean the metal at the welding site. Then we take the puck and weld it inside the protective casing (right in the center). We weld a nut to the puck.

After that, using a drill, we drill two holes in the casing on each side. We process them with a file so that there are no sharp edges.

We install the finished nozzle on a trimmer for grass, and fixed with a nut. Then we insert a fishing line for a trimmer into drilled holes.

A universal disc for a trimmer for grass from a diamond disk

If you have an old diamond disk, do not throw it just into scrap metal. From it you can make a universal cutting disc for a gasoline trimmer for grass.

Such a homemade disk has a lot of advantages. Firstly, it cuts dry small grass quite well, which a fishing line does not take for a trimmer. Secondly, it copes with very hard grass perfectly.

And one of the most significant advantages of such a disk is that it saws well bushes and trees, the trunks and branches of which do not exceed in a diameter of 12 cm. The disk is 180 mm at a time cut to 60 mm.

The whole secret of high performance of a home.made disk is in the form and number of cutting teeth. In many ways, it is thanks to the special shape of the tooth that the disk does not burrow into wood, and also does not lose momentum even on a weak trimmer.

The main stages of work

Please note: if you use a diamond disk for an angular grinder, then first of all you need to drill a landing hole in it. The fact is that the disks for the angular grinder have a hole diameter-20-22 mm, and in most trimmers-25.4 mm.

After adjusting the landing hole in size, attach a paper stencil to the disk. The stencil itself can be downloaded from the link.

To exclude damping slots and holes in the disk that serve to cool and remove dust, you will have to reduce the initial disk diameter to 180 mm. Next, we cut out a paper stencil clearly along the contour.

The hole in the center does not need to cut. We clean the surface of the disk of rust and dirt, apply the stationery glue on it, align the stencil exactly through the landing hole and press.

Disk manufacturing process

At the next stage, we cut off the angular grinding of a diamond disk along a glued stencil. Then we remove the remnants of the metal with a cleaning disk, reaching the edge of the stencil.

Along the way, the master cuts out damping slots in the disk. We process the edges with a petal circle and then remove the stencil.

After that, it will be necessary to dilute the teeth. You can do this with ordinary pliers. However, to make the angle the same, the author uses special wiring. Odd teeth need to bend to the left, even. to the right.

Further cutting teeth must be sharpened. The optimal angle of sharpening is 15-18 degrees regarding the center. If the metal is soft, then the ends of the teeth must be hardened. To do this, just heat them with a gas burner reddened and dip in machine oil.

Grace from an old trimmer for grass with your own hands

One of the problems accompanying gardeners and gardeners throughout life is the need for the disposal of grass, weeds, as well as falling foliage. It has long been the owners of land plots have learned to receive a wonderful fertilizer from plant residues. compost. At the same time, to improve its quality, it is desirable that the starting raw materials have a small fraction. To do this, we propose to make a simple device with our own hands. a chopper for the grass. It can be useful to those who are engaged in breeding poultry.

The basis of the design of the chopper is an ordinary trimmer for grass, which today available in almost many garden areas. But unlike its traditional position, in the device this tool works from the bottom up.

Basic materials

As can be seen from the given photo, you should prepare: for working on the chopper:

• a metal container or plastic volume of at least 50 liters;
• several metal tubes with a diameter of at least 1/2 inch;
• about 1 sq. m strong steel mesh with small cells;
• a piece of a board of sufficient width. Instead of it, moisture-resistant plywood or wood-based slab, followed by moisture-proof processing, will suit it.
• Prepare durable clamps for attaching the structure to the base;
• several scraps of wooden bars, screws;
• Trammer for grass of any manufacturer with interchangeable working nozzles.
• Electric with a file for metal;
• electric screwdriver or screwdriver;
• electric drill;
• a locksmith hammer with a boy from 0.5 kg;
• small anvil or correct plate.

Preparation of the grinder capacity

We begin work on the device by finalizing the chopper capacity. To do this, at the bottom, it is necessary to mark four holes in the form of quadrangular trapezes with rounded corners located around the perimeter.

Having drilled in each of the segments a hole with a diameter of 10 mm, cut the necessary elements with an electrician. For cutting plastic and metal, we recommend using special files with a small frequent tooth.

After that, treat the edges of the holes with sandpaper, gluing it on a wooden block of suitable shape and size.

For the operation of the device, it is necessary to securely fix the grid at the bottom. For this purpose, use four scraps of coniferous boards and several screws with wide hats. Put the boards on the jumpers between the segments and plunge the screws into the bottom of the tank from the inside. Thus, the lumber attracted to the container will reliably fix the mesh membrane.

In order to optimize the work of the chopper for the grass, the convenience of maintaining it, the working tank is better to place at a small height relative to the base of the device. For this purpose, we will use tubular supports that are easy to make on our own.

To do this, you will need two one and a half meter scraps of a durable steel or aluminum pipe. Bend them with a pipe bend or locksmith. Flatten the ends of the tubes with a hammer on the anvil so that the planes are located at a slight angle to each other.

In each obtained site, drill a pair of holes with a diameter of 6.5 or 8.5 millimeters. Attach the pipe pipe to the chopper capacity, mark and drill the coaxial openings of the corresponding diameter in the necessary places.

After that, connect the tank with the legs using bolts with nuts and washers.

Trammer refinement for grass

To reduce the dimensions of the device and the convenience of its operation, you will have to slightly finalize it and its.

Disconnect the main parts of the tool from the body and cut the cable along with a tubular bar with a few tens of centimeters so that the cutting device of the braid is located at a short distance from the bottom of the chopper container. After that, collect a trimmer for the grass and make sure that the changes did not affect its performance.

Installation of the device

On a strong base from a wooden board, fix the trimmer engine for grass with clamps. Adjust its position so that it is convenient to serve this node, control and add fuel, start the engine and adjust the speed of the cutting device.

We also strictly fix the base of the mowing bar on the base. To do this, you can use its handle, securely fixed in the desired place and pulling steel clamps to the board.

Construct the quality of the attachment of all nodes and carry out a trial launch of a home.made chopper. Depending on the thickness of the stems of crushed raw materials, it is possible to use a cutting nozzle with fishing line or knives. If necessary, to work with gross vegetable waste, you can use the engine of greater power.

For ease of work, it is better to perform raw materials together together. The first employee carries out periodic loading of plants, and the second regulates the number of revolutions of the cutting head of the trimmer for grass.

Dear readers, if you have questions, ask them using the form below. We will be glad to communicate with you

DIY gas generator from a trimmer for grass (25 photos of manufacturing)

A simple homemade 220 V gasoline generator, made from a trimmer for grass, a photo and a detailed description of the manufacture of homemade, as well as video testing.

Gasoline generator. can be useful in case of disconnecting the electric network, at home, at the cottage, in the garage, or in the field. With it, you can organize backup power to lighting, charging phones, video cameras and other equipment.

You will need materials:

We start the engine. Adjusting idle revolutions we set the output voltage at the output of the generator in the region of 220 V.

The result was a homemade benzogenerator with your own hands. The approximate capacity of the generator is approximately 300 watts. This is enough to connect several LED lamps, charge phones and laptop.

The process of manufacturing a home.made gasoline generator and its tests are shown in this

DIY chisels holder

So that the chisels are not lost or stupid, make a simple suspended holder for them.

Choose a tender of dense wood without knots with a thickness of 20–40 mm. And you can also apply plywood, wood.fiber plate or pine glue. Select the grooves in two approaches: first use an electric drill with a feather drill, and then cut grooves with a canvas with small teeth.

Attach the holder on the wall with screws through the holes drilled in the end.

Ready home.made chisel holder.

Planck under the screwdrivers

It is practical to store manual instruments on the back panel of the workbench standing along the wall. If the edge of such a slab has a width of at least 10 mm, then on it you can fix the simplest bar with holes for storing screwdrivers.

For this holder, the laminate wrappers are perfect for the desired length. Drill two rows of holes in it, calculating the placement of large screwdrivers in the far row, and small ones in the near.

Attach the panel-holder with self-tapping screws directly to the end of the back of the desktop.

Garage affairs, or put things in order in the garage (Continuation of 65)

Today I decided to go to the garage and continue to work, despite the malaise.In the past days it blew somewhere. But you need to work while I stand on my feet.

Yesterday, I were in the garage with Dmitrius and a little bit of the next “order”.In the sense that they decided to put a little on the boxes the contents of numerous packages accumulated near the left wall.I instructed the boxes from under the machines, pulled everything out and threw the boxes into the trash, excluding the packaging from the strip saw-a good large piece of cardboard. Come in handy for car repairs.Put a cooler in their place, where he should stand.

Temporarily signed boxes to understand where and what to lay out.

In general, we tidied up a little, freeing up a place for a shelf for a power tool.

Among other things, I decided to reflect on how to place a power tool yesterday.For this I gathered everything together on the floor. And then measurements, shifting.

As a result, he sketched a drawer of the future shelf.

And today I decided to bring the drawing to life.After 4-5 hours I got this design. Trying on the place.

At the very top I will stand the most difficult tools, so the upper shelf is made of 18 mm plywood.

Two following shelves from 15mm plywood.

In the upper photo, you can see the absence of one shelf. I just did not know how to place a drill and left it on “then”.After some measurements and thoughts, I made a hole in the shelf under the neck of the drill and had to be slightly rubbed a little so that the drill was inserted not strictly vertically, but a little at an angle. Here is such a cunning hole with an organician.:)

Before hanging the shelf, I went through a grinder (prepared for painting), cut out a hole for the forks to the charger.I fixed on the wall using turnkey screws (plumbing fasteners), on which everything in the garage was hanged.

Well, like that, approximately, it will live everything.

You may notice that there are no departments under the cables. The cables will be deleted and all the tools are converted to the system of quick.sitting cable.That is, this cable “curtain” will not be. At all.:) And one shelf remained not involved. Under the future tool.:)

Today is all.To be continued. I don’t know when, in the evening I began to feel worse. I will be treated.

Garage affairs. Stage 7. Road for wheels Drive2

Rabberry for the wheels.At the beginning of my blog I want to write that the rack does not comply with the standards. And yes, yes, yes I saw this picture:

Personally, I believe that this is not entirely truth if the wheels are stored seasonally, and not lie in warehouses for years. I came to this conclusion from my personal experience of storing rubber.

Staying wheels with disks standing is not recommended, because what? Because it will lead to deformation of the tires or to what else? If so, then how to explain why they are not deformed when cars are seasonally standing in garages for the whole winter, or even longer? And many cars are just like that. over, in this case, not only the weight of the tires and disks, but the weight of the entire car presses on the wheels. Maybe I don’t understand what, then write on the merits of the question, and do not throw just the picture that I brought above in the text.Sorry for such an emotional beginning, but in a stranger like a blog, where a person shared his idea of ​​a rack of him, all who was not too lazy to teach him, and without justifying his words except this notorious picture.

In general, I made a rack as I did for it was limited in the means and useful area of ​​the garage. Especially the minuses in such storage did not find significant. Hanging the wheels is certainly good on the wall, but in my opinion, this is not permissible luxury in my opinion. About the minuses of storage pile I will write below.Well, now actually about the rack itself.

Each garage should have a regular place for storing rubber or wheel assembly.I used to have a set of rubber and casting just lay in the corner with a pile.

And after buying another set of such stacks, there were two. A lot takes a lot, and indeed interfere. Plus, in the corners where the wheels lie, the zone stagnant for air forms and therefore moisture formed there, which you understand, it is not good.

Again, of course, you can argue for a long time how and where to store the wheels is right, but I don’t have much place in the garage, and I decided to make a rack, which I performed my function and did not occupy a lot of the place. I decided to make it from the bars purchased in the store “Level”

Drawing a rack design in his head and leaflet, he set to work.

The first on the first I washed down 4 identical bars for the frame (verticals).

Marked and made cuts in them with an electrician.

Drank horizontal bars and began to collect.

Attached bars to each other with self.tapping screws, previously sprinkled holes with a thin drill.

Already the appearance of the rack is drawn:

To strengthen the structure in the lips, made diagonal jumpers:

4 pieces

Well, in order to completely consolidate the result I strengthened the entire structure with futings.

He enters the shelf exactly under the shelf. Respectively, the set of rubber is included in it exactly.

The OSB sheet laid on the middle shelf and here is another very spacious and functional shelf.

Garage affairs. Stage 1.Garage affairs. Stage 2.Garage affairs. Stage 3.Garage affairs. Stage 4.Garage affairs. Stage 5 shelves in the garage.

Cases Garage Stage 6. Wolf in the garage:. Wolf in the garage part 1. workbench in the garage part 2. mounting countertop.- workbench in the garage part 3. tool screen

Garage affairs. Stage 7. Road for wheels.Cases Garage part 8. curtain in the garage.

How to properly store a trimmer for grass

Trimmer for grass (electric or lawn mower) is a popular and useful garden tool for mowing grass, weeds and small shrubs. The technique is quite complicated, you need to correctly contact it, but also store it. Particularly important is conservation for the winter. Sometimes the owners of such equipment simply throw it into a pantry or garage for the whole winter. In such conditions, by the next season, the unit may fail. Therefore, it is important to correctly approach the conservation and organization of storage conditions.

Which affects the characteristics of a trimmer for grass

The technical condition of motorcycles during storage can change due to such factors:

• The quality of the device itself. If the manufacturer used low.quality materials and components, they themselves become unusable faster, for example, rust.
• Package. Should protect against dust, moisture and mechanical damage.
• Temperature. Should not fall below 0 ° C. Especially relevant for battery models, since the battery in the cold quickly degrades.
• Humidity. Excess moisture leads to corrosion damage to parts.
• Training. Before storage, the device must be properly served.

Storage features

There are two main types of motorcycle. gasoline and battery. The rules of their storage are mostly convergen for some nuances. In any case, the conservation should begin with thorough maintenance and preparation of the unit.

Training

Preparation of a benzotrimer begins in this way:

• Fuel and butter.
• Let the apparatus work at idle so that it consumed all the fuel left in the carburetor.
• Spin and inspect the spark plug. The electrode should have a reddish color. If there is a car, the candle should be cleaned or replaced.

Eletric trimmer for grass should begin to be prepared for conservation as follows:

Further, the rules are the same for both types of motorcycle:

• Remove the remaining grass. She can accumulate between fixed nodes and knives. Blades also need to be carefully cleaned. If there is organic pollution on the case, they must be carefully removed.
• Dismantle the cutting knife. Check it for mechanical damage. If there is a part, be sure to be replaced, this can be done immediately or before the next season. Store a knife separately.
• If the lawn mower is equipped with a trimmer cord (fishing line), it should be dismantled and keep in a wet place until the next season. Before the new season for several days you need to leave in clean water. Thanks to this, the fishing line for the trimmer will remain elastic, which will extend its service life.

Where and what to store

It is extremely recommended to store motorcycles in limbo. The steering wheel often interferes, so it can be dismantled or simply turned the other way. As for the choice of place and packaging, the following options can be distinguished:

• The optimal storage location is a garage or a separate building for garden equipment. The main thing is that the room is dry and well ventilated.
• If there is no separate building, a trimmer for the grass can be kept in the pantry of the house or apartment. It is desirable that the room is not very dusty, which is especially important for electric motorcycle. A large amount of dust absorbs moisture, as a result of which it begins to conduct electric current, which is fraught with a closure.
• It is better to use factory packaging in which a trimmer for grass was sold. Very good if it has a foam, it will absorb excess moisture. In such a package, the device is not necessary to hang.
• If there is no factory packaging, you can use a cardboard box of a suitable size.
• You can apply a suitable cover of dense fabric, for example, tarpaulin. In such a package, a trimmer for grass will be conveniently hanging on the wall, to save space.
• You can build a box of boards or plywood. However, in such a box, the lawn mower will take up a lot of space.
• Trimmer for grass can be wrapped in a breathable fabric.
• If there is no packaging at all, it is recommended to store the device in a suspended form. This will protect the details from mechanical damage and will save place. But, it is important that there is no dust in the room, especially from building materials. For suspension, it is enough to mount a hook of the corresponding size into the wall.

Useful tips

To avoid premature failure of a trimmer for grass, follow the following recommendations:

A universal way to fix the drill horizontally or vertically

From time to time in everyday life, there is a need to polish something with your own hands, but if there are no conditions and a special tool, the question is postponed or reassured in another place, but already for money. However, in fact, everything is not so difficult, just should take a drill, equip it with a grinding nozzle and fix it well on the table in the right position.

You can do without a table, taking a piece of a wooden bar for this is more powerful. In my example, a block of 100×50 mm about 80 cm long was used. The longer the bar, the more stable and it is easier to keep it without using additional mounts.

Studs for clamps with M8 thread. Studs for clamps with M8 thread.

In addition to the bar, you still need to get a couple of plumbing metal clamps. the size of which allows you to clash the drill in the narrowest places. Near the cartridge and on the handle. Under my drill, inch clamps approached, designed for a circle diameter of 32-37 mm.

Studs for clamps can be included or selected separately, depending on specific tasks. I bought separately a couple of hairpins for 120 mm.

The clamps collected and fastened to the drill helped to make markings under the holes. Holes diameter 4-5 mm. After their drilling, it only remained to screw the clamps and fix the drill with screws.

Drill prepared for grinding. Drill prepared for grinding.

With clamps of this size and this method of attachment, the only drawback. This is not a parallel position of the drill in relation to the bar. If it were wider or one of the clamps was larger, for example, 100 mm in a dimeter, this would allow you to set a drill in any position.

The drill attached to the bar can be used both on horizontal surfaces and on vertical, only additional fixation is required. You can even mount the clamps right on the vertical wall and then nothing else will be needed.

In my case, you can not hold a bar with a drill at all, grabbed a self-tapping screw to some table or step on it and hold it with your foot. In general, you can choose the position of a drill for grinding based on tasks and conditions, and use it in the apartment on the table, on the balcony, on the brick wall, on the ground or even on the concrete floor. Here is such a simple idea.

Elka optimized the space on the balcony

Previously, bicycles stood there on the balcony, and took a bunch of place. Now we keep in limbo, because it is a pity to take it to the garage: there is a higher humidity. Storage hooks accidentally saw and bought in a bicycle store.

IVAN EGOROV uses a bicycle instead of hangers for jackets device horizontal holder

The system is attached to the wall and allows you to store several bicycles at once. For convenience and saving space, you can remove the pedal and the steering wheel. So that the bicycles do not scratch, the holders on which they hang the bike are covered with soft material. Holders, if necessary, can be folded.

Users recommend not using fasteners that comes with it, but to buy separately.

Gleb Tyshkevich does not advise hanging on an eye

I bought folding “horns” at the “sportsmaster” several years ago and hang on them. The only thing. wryly measured where to hang. As a result, the front wheel does not fit, so I hang obliquely, on the crown of the fork. And he chose incorrectly heights: if you hang behind the rear triangle, then the saddle rests on the shelf above the bicycle, and I don’t want to put the height of the saddle every time each time.

It would be the most correct to overshadow and outweigh the “horns”, but so far lazy. The thing is excellent, but you need to consider how much free space you have, and try on where to hang wisely, and not by eye, as I.

Alexander Nikolsky fit on the horns two bicycles at once

The corridor is large, allows you to hang two bicycles on the “horns”. They withstand if the anchors are replaced with more, since the complete are slowly leaving the wall. The third bike stands under them.

Oksana Komarova saves bicycles from animals on the wall

Hanging one on the wall for a fastening from the decatlon, the second stands on the floor. The apartment is tiny, but the place was found. Nizhny is stable only when it stands on the machine. I think to add a hook so that it does not overturn. Animals buoy

Storage system device for vertical suspension

Return and exchange

Any mounts, shelves, brackets and suspensions after buying in our store can always be handed over back. To do this, you must independently bring the purchase in the commodity form to our warehouse, or make a return fence with a courier.

Wall.mounted tools for storing tools

A lot of different tools, inventory have been collected in the garage or workshop. If you do not think through the storage system, then finding the desired item is not so easy. To put the perfect order in the garage and save the time spent on the search for a particular tool, you need to collect all the necessary items in one convenient zone. For this, the tool attaching the tool on the wall is ideal. Thanks to this location of the tools in the room, the useful area is released, the useful area is released. All the necessary devices are placed in sight.

TOP of the best ideas for storing tools

Since the tools are long and short, large and small, different in shape, then the ways of their storage differ. There are several techniques for systematizing tools. Below are the most convenient and popular of those that can be made with your own hands right on the wall.

Vertical storage systems of type rack

One of the varieties of vertical storage of tools is a system in the form of racks. On racks, you should arrange the most necessary tools that can be placed in close availability. Items that are required less often are cleaned on long.range racks on the upper or lower shelves. Metal shelves for garage. IF systems. are perfect for this.

But even with a large selection of options, the proposal will not always satisfy the necessary requests of the owner of the garage. Therefore, it is recommended to combine purchased racks with holders and regiments made by yourself, or completely construct yourself a wall.wall storage system.

Vertical home.made wood racks with slots for storing wrench and screwdrivers are very convenient. On them you can easily place the bushings for attaching the tool with a conical shank of different sizes or pliers.

Vertical rack in the form of a mobile stand. a great choice for placing an improvised tool. It is recommended to make it from wood or plywood. Separate groups of tools are located on hooks, magnets or shelves. Often use special peopanels for the vertical storage system.

Magnetic tape

The magnetic tape is simple and convenient to use. Magnetic stripes are taken for attaching the tool and mounted on a wall storage system. The most different tools can be attached to the tape: from small metal wings and screwdrivers to large objects.

Plastic containers

You can easily organize the storage of even the smallest items by collecting a system of small containers. You can store them:

The most affordable way is plastic bottles of different sizes or plastic containers, as well as small glass jars. The containers can be placed on the vertical system by shelves or attached directly to the wall to save space.

Plastic opaque canists with a cut off are also suitable. If desired, they can be signed or numbered.

Organizers

For storing small details and objects, you can easily construct an organizer with your own hands:

• Take any box from an old unnecessary table and make a lot of small partitions inside it from cardboard or plywood. Thanks to individual cells, all small necessary details will always be in their place, sorted by the configuration.
• If you make an organizer yourself, you need to take a piece of polystyrene. it will be the bottom of the organizer, and for walls and partitions. PVC (glue it with glue to the bottom), for the lid you can use transparent plastic or glass.
• Simple and quickly you can make an organizer for screwdrivers. It can be made according to the instructions, as in p. 1 or 2. And you can drill the holes of the desired diameters in a bars of wood or foam, then attach it to the wall and insert it into the holes of the screwdriver. All objects will be in sight and will not be lost.
• Another version of the organizer is assembled from cans of different sizes. Tins women are quickly and firmly attached to the vertical wall in any convenient position and are filled with either small details or tools.

Garden tool

Garden tool always takes up a lot of space, clutches the passages. This can be avoided if you choose one of the walls of the garage or workshop and convert it for storage of garden inventory. It is recommended to use ordinary pipes from PVC to create a storage system, make holders in size of garden inventory and other things:

There are very simple options for fixing the tool in the garage:

• Sad inventory racks. They are made of ordinary wooden pallets. It is leaned by the bottom against the wall and fixed with self.tapping screws, they are nailed to any sizes of the rail.
• Another simple way is the usual strong and reliable wooden or metal hooks along the entire wall, where you can hang inventory, extension cords of different sizes. Stronger brackets and shelves can be used to store wheels, tires, inflatable boat.