The trimmer for the grass ceased to develop the moment. Why are there a moment

Trimmer for grass loses power to hot. The lawn mower does not develop full power

A braid braid with a gasoline drive is a useful thing for owners of personal plots, lawns, and when a trimmer for grass suddenly stalls, the work on cleaning the territory stops from the grass. The device itself is a rather complex mechanism, so there are many different causes of its breakdowns. The most common problems contain instructions for operating. Know the reasons why the trimmer stalls for the grass, it follows to independently effectively perform the repair of the device.

Malfunctions with a benzocosa associated with the fact that this device is not started, in a certain way are classified by specialists of service services. They stand out malfunctions with the following nodes of the mechanism:

  • the engine in which the piston and bearings can be worn out or fail to crack the crankcase;
  • the fuel supply system, while it is possible to clog the filter or problems with the carburetor;
  • mechanical damage to wires, tubes, hoses;
  • The ignition chain.

To correctly determine the knot where the breakdown occurred, it is necessary to pay attention to the circumstances of the trimmer stalls for the grass.

When pressing gas

If the lawn mower stops when pressing the gas, then the reasons may be the following.

  • The most common option is Carburetor adjustment failure, which occurs with significant loads on the drive, after prolonged inaction of the mechanism or when using it in severe conditions.
  • Flaw valve clogging, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
  • The weakening and hanging of the cable in the carburetor. It can also arise Stretching of the fuel hoseup to its break, caused by the action of a significant load.
  • The clogging of the sapun(check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower

Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

When to contact the workshop

If the device is under warranty, at the first signs of incorrect operation, it can be safely attributed to a specialized workshop. Repair will be made for free, regardless of the nature of the damage, if it happened not due to the fault of the owner. In case of breakdowns in the engine, an ignorant person in technology, it is better to immediately contact a specialist. In any case, the degree of seriousness of malfunctions with the unit is determined by the user himself.

Summarize. Both gasoline and electric trimmers for grass are designed for many years of reliable work. Most of the problems described above occurs due to the insufficient attention of the owner to his assistant. Subject to strict compliance with the requirements from the manufacturer and regular maintenance, the manual mower will work rhythmically and without interruptions.

Reasons and repair

I wish to share my experience to restore the desired power of a trimmer power for grass with an internal combustion engine.

Once, first June, I began to notice that my trimmer for the grass of the GT22GES model (manufacturer Echo) began to lose its former power.

In the process of working with grass, even with a small increase in the load (grass higher and thoroughly), the turnover fell and the efficiency of the work was not the same as it was previously.

Previously, a trimmer for grass did not generally notice such obstacles. With a sharp press on the trigger without load, the turnover increased slowly, it seems to be reluctant to.

He took the management of the user on a trimmer for the grass, found in it a section of the malfunction and their elimination. I chose a suitable malfunction in the table, which is described approximately like this: the engine is poorly accelerated or fades.

In the midst of probable circumstances, pollution of the air filter, fuel filter, clogging of the drainage opening of the fuel tank, the spark plug, carburetor, clogging of the cooling system, clogging of the exhaust channel or muffler.

As it turns out, a list of probable circumstances is wide where to start?

At first, the air filter, a drainage hole, an air radiator looked at the visually, all this was in the usual state.

Later I decided to look from the end of the list, in other words, check the exhaust system of the exhaust channel and muffler.

To do this, he took off the candle tip, unscrewed three screws and removed the plastic protective lid of the muffler (in the drawing in the manual under 5). Then unscrewing the two long screws, he carefully removed the muffler, so as not to destroy the two gaskets that are there.

The foreboding did not bother me. The output channel of the motor cylinder (through which exhaust gases emerge from the cylinder) was packed with a gun by 30 40.

So this is the reason for the disorder of the work of my trimmer for the grass!

Caution, so as not to destroy the surface of the piston and prevent third.party goods (in other words, that Nagar) Immediately cleaned the exhaust channel from the carrier, carefully purged the channel using the pump.

The Truman Show. Truman realizes he’s being watched

I used a knife as a tool (but only with the edge of the channel), and in the depths of the channel a woody and plastic spatula of a suitable size.

The muffler was quite unsuccessful and snus.

After the assembly, he started a trimmer for the grass, warmed up a bit and tried to mow the engine earned like a new one, the power increased noticeably, the grass does not mow, but cuts (a fishing line for a trimmer three mm).

Read Lawn Mushroom mowing stalls at high speeds

It’s nice that the device began to work excellent and it is doubly nice that he managed to find a malfunction and remove it.

How to Setup/Unbox Radley Cordless Grass Trimmer & Blower|| Grass Trimmer & Edge Mower Review

It is possible that such an inconsistent can appear in other models of trimmers, because their design is approximately similar and all trimmers for grass have a graduation channel and a muffler.

Ways to eliminate breakdowns

The following works are possible by carburetor:

  • cleaning and adjustment of the fuel supply valve;
  • similar work with a valve producing spent gases and pairs (after fuel burning);
  • replacement of the spring weaker on the entrance valve;
  • restoration of the tension of the carburetor cable;
  • replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
  • changing the rotor damper disk;.
  • Change of faulty wire or ignition coil.

The list of work on the work may also include the cleaning of the nozzles (in a 4-stroke engine), replacement of the valve washer, gaskets in tanks and so on.

Operating advice

It is worth paying attention to several recommendations for working with a benzoca or a trimmer that extend the service life of the device to several times.

  • As soon as you notice that the lawn mower or trimmer vibrates for the grass. immediately stop working and check the serviceability, performance of specific parts.
  • Valves adjustment and checking the work of pistons and cylinders, cleaning and changing the nozzles perform, starting from the requirements set forth in the user guide and the recommendations of the masters of service centers.
  • When air bubbles enter the system due to impaired fuel hose-give in to gas. With the combustion of gasoline with higher speeds of the gas bubbles motor will be less. But this is a temporary measure. As soon as possible, disassemble the unit and eliminate the cause of the suction of excess air.
  • Do not work as a unit in cold weather, not heating the engine. under load it can often stall. The effect here is the same as in the case when the driver in.40 started the car and immediately drove off, without waiting for the engine heating.
  • Do not leave the unit on the roadway. During the accident, the hit will immediately break, and this will make the purchase of a new unit for a forced measure. A car that has crashed into it at best will receive damage to the body and bumper.
  • Avoid working with a motorcycle or a trimmer in a downpour. Water getting along with air in the worst case can lead to engine explosion. Similar situations arose with cars.
  • Do not use unverified vehicles and lubricants. The mower warms up the engine more than it would do the car itself. when overheating, it will automatically lose its lubricants. It will turn into a burned out reagent. sticky, too viscous and viscous, like fuel oil. He will immediately stall (and drown out) the motor.
  • If the oil is old, previously merged from the tank of the machine or other (or the same) lawn mower (on a 4-stroke engine)-defend it, filter to clean from dirt and metal. But at the first opportunity, purchase fresh motor oil.
  • If the engine is two.stroke. observe the ratio of gasoline and oil. For compositions with mineral oils, this is approximately 34: 1, for semi.synthetics. 42: 1, for purely synthetic. 50: 1. Do not violate these proportions: “rewinded” gasoline will not burn out and quickly clog the engine, “under.appropriate”. will accelerate the wear of its mobile parts.
  • In terms of viscosity to winter classes, they include marking oils: SAE-0W/5W/10W/15W/20W/25W. To the summer-SAE-20/30/40/50/60. For example, SAE 10W-40 is already all-season oil (when working mowers from spring to autumn inclusive). Be sure to check with the manufacturer exactly what oil is needed.
  • Always use high.quality gasoline that has passed the manufacturer all stages of cleaning.
  • Recommended octane number of gasoline-AI-92/95/98. The use of the 76th can lead to a non-power of the engine by frequent stalling if you are poured, for example, the 76th or 80th gasoline.
  • If you are not sure of the independent solution of problems with a gas station (which does not gain move and often stalls)- call the master or contact the service center for repairing motor and garden equipment. Specialists do not get used to doing this work for you.

Observing all these precautions, you will give your mower for many years of fruitful work, and yourself. the luxury of well.groomed lawns, comfort and convenience when mowing unnecessary vegetation in your site.

The gasoline trimmer for the grass starts and stalls

Why is a trimmer not starting for grass gasoline? Reasons and their elimination

Recently, a gasoline trimmer for grass has acquired the status of one of the main tools in the arsenal of summer residents. And this is not surprising, because a motorized braid for grass allows you to quickly put a personal plot in order. However, sometimes it happens that the trimmer for the grass does not start hot and even on cold. In such situations, you have to independently establish the cause of the malfunction. Let’s find out what to do if a trimmer does not start for grass. The reasons that most often lead to such troubles will be considered further.

Diagnostics strategy

Where to start the diagnosis of malfunctions if a trimmer is not started for grass? In situations where the tool stalls immediately after starting, it is worth examining the following units:

It is the breakdown of the above locations that most often leads to the fact that a trimmer for grass is poorly started. Let’s look at how to eliminate such troubles.

Checking the fuel mixture

Suppose you don’t start a trimmer for grass. In this case, the first thing is to check whether the fuel is enough in the tank, as well as evaluate the quality of the fuel mixture. To refuel a motorized unit, it is necessary exclusively high.quality gasoline. It is recommended to use fuel, the brand of which is not lower than AI-95. Refueling a trimmer for grass with fuel of unknown origin, not bought at a gas station, is fraught with frequent failures in the work of the tool. This can cause a breakdown of the cylinder-piston system. Repair in this case often exceeds the cost of the device itself.

Why is a trimmer not starting for grass gasoline? Incorrect preparation of the fuel mixture may also lead to this, which consists of oil and gasoline. The proportions in which the specified components are connected are indicated by manufacturers in the guide for the operation of a trimmer for grass. Preparing the fuel mixture is extremely not recommended in large volumes, that is, for the future. Indeed, with prolonged savings, there is a loss of the determining properties of the substance. Therefore, if a trimmer for grass does not start, it is worth draining the old fuel and use freshly prepared fuel mixture.

Read which trimmer for grass is better than rotary or vibration

Diagnosis of the candle channel

What to do if the used fuel mixture is in perfect order, but a trimmer for grass is still not started by gasoline? The reasons for the refusal of the mechanism may lie in excessive moisture of the candle channel. To diagnose and eliminate the problem, it is necessary to do the following:

  • To twist the candle. Wipe it thoroughly, and then dry it.
  • Drain excess fuel in the chamber through the corresponding candle hole.
  • Clear the old candle if there is a dozen on its surface. Cope with the task will allow the use of a conventional ladies’ nail file or file.
  • When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the lumen.
  • Collect a functional block back.
  • Try to start a trimmer for grass.

It is recommended to perform a candle channel to dry for at least half an hour. However, in no case should you resort to the calcination of its elements. After all, heating the spark plug can lead to its final corruption. Что предпринять, если обслуживание функционального блока было выполнено в соответствии вышеуказанным рекомендациям, но триммер для травы не заводится, искра есть при этом? In this case, it should be treated with gasoline threaded connection. The latter does not need to be saturated abundantly fuel. It should only be slightly moisturized. Resort to such actions should be to ensure the ignition. After all, no matter how much the candle gives a strong spark, in an absolutely dry chamber there simply will not be something to ignite.

The lawn mower stalls

Carburetor adjustment, well start

,stalling when pressing gas. My Skype: Ork.Vitek tel. 380979677418

The lawn mower stalls or suffocates when you press the gas

Even more information about the repair and choice of tools on our website www.Looktool.Ru, we are happy for everyone.

If even in this case a trimmer for grass does not start, it is worth evaluating the quality of the contact between the high.voltage wire and the candle. In the absence of a spark (in the presence of a reliable connection between the indicated elements), most likely, the problem is caused by breakdown of the ignition unit. In this situation, you will have to turn to the services of masters who will reinstall the knot.

Checking filters

Another common cause, due to which a trimmer for grass does not start, is the presence of a blockage in the filter area. To confirm the conjecture, just dismantle the indicated block and try to start the unit without it. If the engine of the trimmer for the grass has launched, most likely you will have to replace the air filter or at least perform a thorough purge of the old. In the presence of abundant contaminants on the surface of the filter element, it is necessary to use a new grid. Relying to such actions, you should not leave a suction pipe at all without a filter. After all, rush in this case can lead to the need to repair the entire piston group of the unit engine.

Cleaning the soundtress

Often the engine of branded models of trimmers stalls as a result of clogging of the soundtress. The main task of the specified component is to align the pressure in the fuel tank. In the case of contamination of the node, a vacuum is formed here, which significantly complicates the supply of fuel. Eliminating the malfunction allows the cleaning of the saapon using a conventional sewing needle.

Diagnosis of the graduation channel

The stable functioning of a trimmer for grass can be impaired as a result of laying dirt in the graduation canal or the formation of a blockage on a muffler grid. This problem most often occurs during the operation of older generation trimmers. The issue is being solved by dismantling the anti.diploma mesh and its cleaning.

How to prevent sudden breakdowns during the operation of a trimmer for grass?

So that the unit is always in a functional state, it is worth observing several simple rules:

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

  • When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
  • To clean the tool, you should use kerosene, solvent, or other washing tools.
  • You can not clean a hot tool. it must cool before washing.
  • It is important to observe the recommended working mode. this will avoid overheating of the engine.

To store the tool in cold weather, you need:

  • completely drain the fuel;
  • disassemble the lawn mower, wash and clean all available components;
  • inspect the condition of the parts, eliminate all defects that can be corrected;
  • pour the required amount of oil into the gearbox;
  • Clean the air filter;
  • perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
  • To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

trimmer, grass, develop, moment, there

At idle

At single speeds, the common reasons for stopping a trimmer for grass are as follows:

  • reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel mixture;
  • clogging of the throttle;
  • air entering the system;
  • not enough fuel for the operation of the lawn mower.

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

Immediately after you started

The unit can stall immediately after the launch, if the carburetor is cesspool or was incorrectly configured. this causes Uneven fuel supply

The result is that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting according to the instructions for the mechanism.

The engine also stops when Clotting of the valve

, supplying fuel. In such cases, it is enough just to clean it. If the lawn mower at first earned, but then immediately stalled, then possible fuel to the carburetor unit enters some difficulty. The weakening of the valve helps to solve the issue, which provides free circulation of the mixture in the system.

The stop may also be called Air suction

In the presence of mechanical damage to the hose (holes, cracks) that fuel fuel fuel. In this case, the drive should be added to the drive to quickly drive air bubbles from the system.

Why stall the engine of a trimmer for grass when recruiting

The most popular with summer residents, gardeners and gardeners trimmers for grass are equipped with two.stroke engines operating on gasoline. In recent years, part of the manufacturers have been promoting motorcycles and leaflets based on four.stroke engines in the market, but they have not yet gained the popularity that two.stroke. They are more difficult in the device, more demanding on the mode of operation, purity of fuel, oil quality. Also, four.stroke engines are more in weight and more slowly gaining momentum.

During the operation of trimmers on the basis of two.stroke engines, a number of characteristic malfunctions arise related to the features of the design of the engines. With all the perfection of the Husqvarna or Echo engines, even they occasionally “acting up”. The budget models of motorcycle assembled in China, problems arise more often. This is due to both the lower quality of materials and the assembly level. The most characteristic malfunction is a poor launch from a “hot” state and “subsidence” of revolutions at a slight load. But sometimes a trimmer for grass stalls with a sharp press on the throttle key. Why does this happen?

The reasons for the breakdown

For all the apparent simplicity, the lawn mower is a well.thought.out and balanced tool in which each part is in its place. If everything is regular, the engine from the cold state should start after the first starter jerk. Depending on the model, first you need to swing the fuel mixture by pressing the transparent button on the carburetor. In a number of modern fuel pumping models, it is not required.

You also need to transfer the lever on the carburetor to the extreme position to close the air damper. In some models of Husqvarna and other manufacturers, the shuttle of the damper is carried out by turning a special regulator. After that, you need to turn on the ignition on the handle and energetically pull the starter’s cord, while pressing the gas key to about half.

The engine should start after the first jerk, but can earn after 3. 4 movements. This cannot be considered a breakdown. it all depends on the production of the motor, the quality of the fuel mixture, temperature and humidity and other factors. Two.stroke engines have their own character, to find out why they are not launched from the first, but from the fourth time, it is difficult even for professional mechanics.

trimmer, grass, develop, moment, there

If the engine confidently launched and earned, but the trimmer for the grass stalls when pressing the gas, then you forgot to transfer the carburetor lever to the position of the open or partially open air damper. Usually. this is the movement of the lever down. It may happen that the most stable the lawn mower works with a not fully opened damper. If you have used the trimmer for more than one season, so it will be. When the lever of the damper is transferred to the extreme lower position, the fuel mixture can become too impoverished and the trimmer for the grass stalls when you give gas.

This feature is not considered a malfunction. you just need to check the work of the trimmer for grass in different modes and try to use the optimal one in work. But there are other reasons why the lawn mower can stall at any stage, immediately after starting or during operation.

Other possible reasons

If, with a sharp addition of revolutions, the engine stalls, as if zabulae, then the reason may be:

  • Carburetor adjustment failure. This happens after prolonged downtime or after excessive loads, for example, natives in hot weather or in conditions of strong dustiness.
  • Clogging valve on the tank cover. Eliminated by replacing the lid or cleaning valve.
  • Weakening of the cable of the carburetor regulator drive.
  • Stretching of the fuel hose.
  • Depressurization of traffic jams on the tank, which includes hoses.
  • The clogging of the sapun.

When looking for the reasons why the trimmer stalls for the grass when trying to increase speed, other reasons may appear, for example, associated with the ignition coil and candle. If the fuel mixture is not prepared according to the rules using cheap oil or poor.quality gasoline, the proportions are not observed, or the mixture cooked a month ago, then the engine can also stall when trying to add gas.

How the real reason is determined

In the case when the carburetor is responsible for stopping the engine, a sudden stop is accompanied by a nearby symptoms. Most often, this is the appearance of tangible vibrations in all operating modes. Carburetor adjustment is carried out using two screws. idle control and fuel supply. In which direction to rotate them should be written in the operating instructions. If independent adjustment has not helped, contact the service center or buy a new carburetor.

If you have a lawn mower of a professional or semi-professional class, for example, the same echo or al-ko. then the carburetor resource is approximately equal to the durability of the motor and there is no need to buy a new one. It is enough to seek help in adjustment to a knowledgeable specialist. Motokos type Champion has a slightly lower carburetor resource, it may happen that adjustments will not help. Carburetors of two.stroke engines in the repair are complex, so it is better to order a new.

After making sure that the carburetor works fine, but the lawn mower still stalls, try to loosen the gas tank cover. If the engine operating mode has changed, it means that the lid valve is clogged or clogged. Practice shows that it is useless to clean it. It is better to buy a new cover, it costs a little, and it will last at least 2. 3 seasons.

Along the way, check the tightness of the gas pipeline connection from the carburetor and tank. Sometimes hoses stretch, and air is sucked around around the fittings. With a sharp press on the gas key, the mixture becomes depleted (gasoline is less than a stichiometric indicator) and the motor stalls. This also happens when the gasket between the carburetor and the cylinder is pierced or the bolts of the carburetor attachment are loosened from vibration. Just in case, check them, but do not forget that two.stroke engines are made of rather fragile alloys. If you overdo it with the moment of puffing, the thread in the cylinder can be disrupted.

It is also recommended to check the fence mesh on the hose in the tank, the cork through which the hoses are inserted into the tank and blow the fuel lines. Perhaps they are clogged and a little gasoline enters the carburetor. Especially with sharp pressure on gas.

Having checked and cleaning all the systems of a trimmer for grass, season the tank prepared by all the rules with a mixture and start from a cold state. Let me work out a few minutes at idle and try to mow fishing at medium speeds. After 10. 12 minutes of work, add speed sharply. a trimmer for grass should not stall. If this happens, change the spark plug and perform the same actions.

If during operation a trimmer for the grass, before stall, spontaneously periodically reduces or increases the revolutions, “failures” appear in power, then it is necessary to check the ignition coil and contacts of all wires. Start with contacts, they are quite fragile and can break off or oxidize.

Why and what to do if a trimmer stalls for grass

There are several reasons why the trimmer for grass stalls when the grass. Usually the problem is provoked:

  • wear of engine elements. piston, bearings, crankcase;
  • malfunctions with fuel supply. a carburetor can fail in the device, sometimes a malfunction causes a clogged filter;
  • mechanical damage to hoses, tubes and cables;
  • disobedience with the ignition chain.

Most often, under a load for one reason or another, an old trimmer for grass, which has long been in operation, stalls for a particular reason. But sometimes the owners of new gasoline devices face problems.

Why is a trimmer for grass stalling when pressing gas, increasing speed

If the trimmer for the grass stalls when you give gas, then the problem is usually a malfunction of the carburetor adjustment. The malfunction often occurs if the device was inaction for a long time, and then received a significant load. Sometimes the unit stalls immediately after increasing speed, if before that it was operated in difficult conditions in violation of the rules.

The following reasons are also leading to problems with the performance of the device:

With stretching or rupture of the fuel hose in a gasoline trimmer, the elements that have become unusable must be changed. If the reason is in the clogged valves and filters in the unit, they are quite simple to clean.

If the reason that the trimmer stalls for the grass is caused by problems with the carburetor, the problems are accompanied by vibrations

Another common problem is that the trimmer for grass stalls with increasing speed due. In this case, you need to find the instructions for the device and carry out the reconfiguration of the unit. Often it is enough to weaken the tightening of the carburetor body.

Why does a trimmer for grass stall at idle

Garden trimmer for grass often stalls even at idle. The reasons for the malfunction are usually simple. First of all, the improper adjustment of the carburetor affects performance. it leads to problems both at high speeds and in idle mode. Turning off the device can provoke clogging of an air filter or throttle.

Sometimes a trimmer for grass stalls if incorrect fuel is used for it. The gearbox for this reason overheats and reduces momentum.

If a malfunction occurs, it is necessary, first of all, to inspect the carburetor unit and perform mechanical repair or configuration. If the cause is of poor.quality fuel, you need to replace the mixture with a more suitable.

What to do if the trimmer for the grass starts and immediately stalls

If the trimmer for the grass does not gain momentum and stalls immediately after starting, the problem usually consists in improper tuning the carburetor. In this case, fuel in the system comes unevenly, the gasoline unit vibrates and cannot work normally. Repair consists in reconfiguring a carburetor unit according to the instructions from the manufacturer.

Engine stop causes fuel supply valve. The element must be carefully cleaned, and then installed back in place. If the lawn mower still stalls immediately after starting, perhaps the valve is too tight and it needs to be loosened. In this case, the fuel mixture will begin to circulate through the system freely, and problems with the performance of the unit will disappear.

In some cases, a gasoline trimmer for grass stalls due to the fact that the hose contains damage that pass the air. During the repair, you need to replace the fuel tube with a new.

Attention! If the damage in the hose is insignificant, it is allowed to simply add a revolution drive. This will allow you to drive out air bubbles from the fuel system.

What to do if the trimmer works and stalls for the grass

Owners of garden gasoline units are faced with the fact that a trimmer for grass stalls at large speeds after a short work. First, the device begins to function with jerks, and then gradually stops.

Typically, the reason is the overheating of the system. gasoline in the carburetor simply boils. A trimmer for grass can heat up if the ignition circuit coil or wire is damaged. There is no point in repairing worn details, they are simply changed to new working.

The use of a trimmer for the grass does not lead the use of not disk, but rotary damper in a carburetor

What to do if the trimmer for the grass overheats and stalls

If a hot trimmer stalls for grass, the situation is a great danger to the performance of the unit. Repair should be carried out immediately, otherwise the device will be completely unusable, and it will be more difficult to restore it.

Overheating of the unit usually cause the following reasons:

  • The use of inalitions. pour fuel into the tank with precisely with such an octane number that is recommended by the manufacturer;
  • a large amount of air in the system. for this reason, the enriched mixture releases an excess of heat;
  • non.compliance with the proportions of oil and gasoline in the preparation of fuel;
  • The thick layer of soot on the muffler. soot is a good heat.insulating material, the gasoline braid for the grass during operation is very hot and stalls;
  • The displacement of the axis of the spit.headed head inside the bar. for this reason, the rotation slows down, and the load on the engine increases.

If the gasoline unit stalls, you need to carefully examine it and eliminate first of all possible deformations of the structure. Then it is necessary to study the fuel parameters. If they do not correspond to the recommended, gasoline is replaced with a more suitable. If unnecessary air gets into the system, it is necessary to independently or with the involvement of specialists to adjust the position of the carburetor damper.

Sometimes a gasoline trimmer for the grass overheats and stalls because there is too old fuel in the tank. Use a fresh mixture for the unit, which was stored no longer than two weeks.

Attention! A trimmer for grass will overheat if you use it for too long, or mow with a weak device hard thick grass.

How to avoid breakdowns

Many breakdowns of a gasoline trimmer for grass can really be eliminated if you remove the causes, but if possible, it is recommended to, in principle, avoid faults. Simple measures allow to maintain the unit in a working state:

  • You need to use a trimmer for grass in accordance with the recommendations of the manufacturer. It is impossible to use a weak device for removing hard weeds on the site, it is also not recommended to use motorcycles in excess of the due time. The gasoline unit needs to be turned off regularly and allow it to cool down.
  • During the operation of the device, it is necessary to monitor the state of the cooling system. To maintain performance, the channels in the case are regularly cleaned, like the starter’s ribs. The clogging of the system often becomes the reason that the unit stalls from overheating.
  • After using the gasoline trimmer for the grass, too, you need to clean. In this case, the procedure is not carried out for a hot unit, at first it must completely cool. For cleaning, use solvents, kerosene and other products allowed for use by the manufacturer.
  • Before cleaning, the motorcycles for storage must be drained from the tank, the remains of unused fuel. If this is not done, the gasoline mixture will fall into heavy components and will clog the channels of the carburetor, which will subsequently cause malfunctions. After draining the fuel, the device is launched at idle and waited for it to turn off.

With the onset of autumn, a gasoline trimmer for grass must be correctly removed for storage. First, the residues of the fuel mixture are drained from the device, and then the unit is disassembled, rinse and clean all removable components.

Before harvesting gasoline motorcycles for storage, you need to evaluate the condition of its parts, carry out the necessary repair and replacement of nodes. Air filter needs to be cleaned. The engine is partially disassembled, rinsed and blown by moving elements, and then applied a new grease. To maintain the piston part, the candle is unscrewed and the piston itself is lifted to the top point, and a little oil is poured into the opening opening and the crankshaft is twisted several times.

trimmer, grass, develop, moment, there

Store a gasoline trimmer for grass in winter is necessary in a warm room

The lawn mower stalls hot? There is a solution!

The lawn mower stalls hot-this means that there is already a certain amount of fuel for starting the engine, but after 5-10 minutes of operation, it stops working in the engine. This motor behavior indicates problems with the fuel filter.

What to do if a benzotrimer is not gaining momentum ?

If you once purchased a trimmer for grass, working with gasoline, then you probably had to face the problem of turning on a trimmer for grass, as well as a problem as a benzotrimer does not gain momentum.

That is why this article has been created.

So, what to do if a trimmer for grass, working for you for several years, suddenly just stops gaining momentum, and the motor simply stalls? In this case, you and I should consider a number of problems related to stopping the work of the motor.

The motor may stall under various circumstances. Sometimes the reason for the incorrect operation of the trimmer for grass working from gasoline is the clogging of the air filter.

It is the filter that is one of the most important reasons why the operation of a gasoline trimmer for grass may stop.

Various garbage very often gets into it, particles of dust that also clog the filter, so it needs to be cleaned and washed every month, and maybe more often, it all depends on what power the gasoline trimmer has for the grass, as well as then how often do you use this device.

Trimmer for grass does not gain momentum, what to do?

Trimmer for grass does not gain momentum. a very common problem and of course does not always have a simple solution.In this

If you have done operations with the filter, but the work of a trimmer for grass working from gasoline remains the same, the benzotrimer does not gain momentum what to do?

Then you should try to extract the filter from the device in order to provide the so.called “relief” of the trimmer for grass. The lawn mower does not develop speed, why the Chinese benzotrimmer STIHL FS. Should help.

The next and rather common problem when working with a gasoline trimmer is that it simply stalls and does not give any signs of life.

In this case, the problem may be as follows:

The last and most common cause of the breakdown of a gasoline trimmer for grass is that the cable that is located in the carburetor department was just sleeping.

Therefore, make sure that it will be well pulled, but not to the limit, otherwise with too much load on the gasoline trimmer for grass, this small cable can crack and then you will definitely have to contact the service center, and then also throw out many money into the wind.

The prerequisites for the breakdowns of gasoline and electric trimmers trimmer for grass, both electronic and gasoline engine (ICE), is an inconspicuous inventory in the summer and autumn period for the owners of cottages and personal houses. With it, weeds, small bushes are removed without effort and the lawn is trimmed. But, as it doesn’t matter what kind of technique, trimmers for grass come out of the string.

Country affairs building and cottage in an understandable language that if the benzotrimer does not gain momentum? If you once bought a trimmer for grass, which works with gasoline, then you probably had to face the problem of turning on the trimmer for the grass, as well as the problem like a benzotrimer, does not gain speed. This is why this article was created. So what to do if a trimmer for grass.

When caring for a personal plot, summer residents periodically face the fact that the lawn mower is not started. There are many reasons for the refusal of the tool. For the correct diagnosis of the problem, the owner of the useful in the country’s dive must know the device and the principle of operation of its individual parts.

Since the gasoline trimmer for grass refers to complex devices, before starting work, it is necessary to carefully study the operating instructions. Very often it is simply ignored, or they get acquainted with it superficially. As a result, when the tool stalls or refuses to start, the question arises. “why the lawn mower is not started?»A long seasonal break in work, improper storage and untimely maintenance of a trimmer for grass, will deliver a lot of trouble to the summer resident, to eliminate the reasons.

Why and what to do if the trimmer for the grass does not gain momentum

If the lawn mower turns on, but does not reach the given power or suddenly stalls, this indicates the incomplete serviceability of its individual parts. Most often, the problem is provoked:

  • bad or too old fuel;
  • winding of grass on the shaft of a knife;
  • clogging of air or fuel filter;
  • engine problems;
  • Falf in the spark plugs.

In all cases, it is necessary to disassemble the motorcycle and carefully inspect its main nodes. This will establish the cause of the failure and carry out simple repair.

The most difficult thing is to repair a benzotrimer with malfunctions of the engine, but such a problem is not common

What to do if a trimmer for grass does not develop speed due to poor fuel

If the benzotrimer does not develop full power, the cause may be in a low.quality fuel mixture. Sometimes the engine in this case does not start at all, in other cases it works with jerks and does not reach the maximum speed.

Diagnostics and repair can be like this:

  • Remove the spark plugs with a key.
  • Inspect their contacts for reddish or dark plaque.
  • If the latter is detected, drain the old fuel from the tank.

Switch raid indicates the presence of a large number of inclusions in gasoline. After removing the old mixture, a new fuel must be poured.

Attention! When using a trimmer for grass, it is advisable to use only the gasoline that is recommended by the manufacturer.

Filter pollution

If a trimmer for grass does not gain momentum in full gas, this may indicate pollution of filters. fuel or air. In the first case, too little gasoline enters the combustion chamber, in the second the mixture is not enough oxygen enough.

You can check the serviceability of the system as follows:

  • Remove the air filter and run the motorcycle without it.
  • See if she is developing a moment.
  • With a positive result, change the part to a new.

If the benzotrimer still does not develop revolutions, you need to test the fuel mixture filter in a similar way. If necessary, it is also changed.

It is impossible to operate a trimmer for grass without a fuel filter, it will quickly break

Wear of the spark plugs

If the lawn mower does not gain a given speed, the cause may be hidden in the spark plugs. The diagnostic and repair algorithm looks like this:

  • Candles are removed and inspected for plaque.
  • If it is, wipe the part from the fuel and dry.
  • Cleaned with fine sandpaper.
  • Check that the gap between the electrodes is 1 mm.
  • Collect a trimmer for grass back.

If the lawn mower is gaining the desired speed again, the problem can be considered solved.

Carburetor malfunction

In some cases, a benzotrimer is turned on during malnutrition of a carburetor, but does not develop the specified revolutions. Repair is carried out according to this scheme:

  • Disassemble the unit and check if the cable in the carburetor is weakened.
  • If necessary, carry out moderate, but not too strong pull.up.
  • Check the settings of the carburetor for compliance with the instructions for the instructions.
  • Clean and rinse the knot itself, and then dried and put in place.
  • Remove pollution from the drive mechanism and lubricate the cable inside it with machine oil.

If the trimmer for the grass does not develop momentum and stalls after all the manipulations undertaken, you should contact the service. Serious problems of the carburetor and engine are difficult to repair with your own hands, sometimes this leads only to the final breakdown of motorcycle.