Trammer for grass Caliber does not start pouring a candle. Chinese lawn mower will not start. The candle is wet.

Trimmer for grass gasoline Champion T334 does not start, wet candle.

Before resorting to more serious repair actions, you must make sure that the graduation channel is serviceable. This section does not apply to previously not used trimmers, since they have practically no production. If the lawn mower is operated for many years and during this time the unit was not subject to serious diagnostic measures, then it is necessary to check the fact of the clogging of the muffler.

The accumulation of soot prevents the exhaust gases from going out, which is why it is simply impossible to start the engine. Of course, on one day the graduation channel cannot clog, which is why such a situation should be preceded by certain signs. The exit of black smoke from a silencer is a kind of incapacity, which gradually accumulates on the walls of the exhaust system. A significant increase in the sound of the installed motor may occur, which is associated with overcoming huge resistance with exhaust gases to release them. When working at idle, the device stalls spontaneously. In critical situations, the engine operation is significantly deteriorated.

If there are serious pollution on the anti.skill net, then the reason for the impossibility of starting a trimmer engine may be precisely in the final channel. You need to clean the mesh as carefully as possible, since it is the black cargo that is a carcinogen that is very dangerous for a person, which can provoke damage to the respiratory tract. For cleaning, specialized tools should be used that will cope with the soil.

The trimmer for the grass is very hot

Overheating of a trimmer for grass can occur for many reasons:

  • Gasoline has not the same octane number indicated in the instructions for the unit;
  • the proportions of gasoline and oil during the preparation of the fuel mixture are not observed;
  • A mixture of fuel with butter has long been prepared (the mixture cannot be stored for more than 2 weeks);
  • The trimmer for the grass works more than the time instructions;
  • A low.power trimmer for grass on thick and hard grass is used, the device works with overload and quickly heats up;
  • shifted towards the bar or the cassette lid clutched.

The latter happens if you install the mowing head inappropriate for this unit

, or when the axis shifts inside the bar. These changes make it difficult to rotate, the load on the engine increases, and it overheating.

How a two.stroke engine works: briefly, but it is important to know for a clear launch of a lawn mower

Lawn mowers are produced with two.stroke or four.stroke internal combustion engines. The difference in the design is significant, but each model starts on the general principle. I show on the example of the Chinese trimmer for Eco grass.

The engine is called two.stroke because the full.time cycle is two tacts: the stroke of the piston from the upper dead point of the VMT to the lower NMT. In this case, the launch occurs with the second achievement of the upper position.

Similarly, chainsaws, boat engines and gasoline tools of another similar technique work. Consider the procedure. We are supposed to figure it out.

To start a trimmer motor for grass, we pull the starter’s cord. Its stretching is spinning a crankshaft with a flywheel creating the moment of inertia. The rotation of the crankshaft shaft is converted into the reciprocating movement of the piston.

The two.stroke motor has 4 working cycles:

  • The first movement of the piston from the VMT to the NMT is accompanied by the injection of the fuel mixture (gasoline with butter and air), when the carburetor inlet valve opens under the influence of the created vacuum;
  • The movement of the piston from NMT to the VMT: the intake and exhaust valves are closed, and the working mixture is compressed in a sealed volume;
  • Both valves remain closed. At the upper dead point of the piston through the contacts, the spark slides through the contacts.There is an explosion of compressed gases. Its strength with an impulse throws the piston down and rotates the crankshaft through the connecting rod;
  • The force of inertia of the flywheel directs the piston from the NMT up: the exhaust valve opens and through it the combustion products are pushed into the exhaust pipe.

All stages are performed automatically, but they are prepared by a person with his actions. When making errors it is made, the benzotrimer does not start and may break.

I try to make out all these points in more detail.

Cycle: what mistakes of beginners lead to breakdown of the engine of the trimmer for grass and exclude its normal operation

6 common mistakes with fuel

The manufacturer in the instructions clearly indicates the brand of gasoline with an octane number, oil and their proportions.

The first three errors are that the user of motorcycles violates all or one of these requirements. The motor will most likely start and work, but its resource may decrease sharply.

A small amount of oil, like its absence, will lead to the fact that the walls of the cylinder will not grease normally, and the piston rings will scratch them, and not slide.

Excess oil will simply burn, forming soot. She will pollute everything, including the piston and cylinder.

Failure gets into the valve, blocks their work, after which the motor will not start.

Will have to disassemble and clean the carburetor, or even put a new. Of course, you can try to wash the piston and the cylinder: it may be possible to bring them into working condition, but it is better not to bring them to.

The fuel mixture must be prepared with high quality and in strict proportion. The repair of a spoiled engine is expensive, about 70% of the price for a new gasoline trimmer for grass.

For the preparation of high.quality fuel mixture, I have a special container with a factory division of divisions in a set of trimmer for grass. Gasoline is neatly poured into it to the level of 500 ml, and then the oil to the required label.

Trench Candle #recycle #wax #outdoor #camping #handmade #candle

An alternative method is the preparation of a fuel mixture with filling gasoline into a calibrated container, for example, a liter canister or a plastic bottle to a label, and an oil additive with a medical syringe according to its divisions.

The dosage with a syringe is more convenient, is considered the most popular way.

Honey Beeswax Candles

I recommend filling gasoline through a funnel with a narrow neck that has a filter: a metal mesh. protection against small garbage.

The prepared mixture should be well shaken and mixed until a uniform color appears. Only after that it can be poured into the tank.

If the mixture does not blame, then it will remain in the tank, and through the carburetor will enter the combustion chamber in portions with different ratios of gasoline and oil.

Fractions of clots of oil clog a candle. The motor stops, stalls, does not start. This is the fourth mistake of beginners.

It should be borne in mind that gasoline is hazardous. The risk of fire exists. Therefore, it is necessary to fill the mixture at a safe distance from the buildings, and in the case of the strait, which often happens to eliminate the causes of a possible fire. Violation of fire fighting measures. error

After pouring the fuel into the gas tank, the latter closes with a screw plug and the lack of leaks is checked. The trimmer for the grass is raised up so that the gasoline fills the cork. There should be no subterations from under the lid or from the fuel hoses.

Lack of such a check. an error can cause a fire.

There is one technical cunning that can cause a benzotrimer motor is not started due to the cessation of fuel supply. If you look carefully at the center of the traffic jam, then a round hole is clearly visible.

We turned Motokosa. Gasoline filled the cork, but does not flow through the hole: there is a sapphone inside. He is working.

trammer, grass, does, start

On the inside, its design is clearly visible: a valve system of plastic and rubber is built.

In the usual state, the valve is pressed to the hole and the fuel does not flow. Когда бензомотор работает, то топливная смесь расходуется через карбюратор. A vacuum is created in the tank. The vacuum opens the valve of the saapon, the pressure is restored.

You should know the two consequences of a malfunction of the sapuna:

  • Constantly open hole. fuel pours out of the tank during its inclinations (excess consumption and the probability of fire).
  • Contamination or sticking of the valve channel is the reason that the lawn mower does not start or stalls.

Check the soundtress is easy: you need to blow it in both directions.

All about the gas tank cover, including the repair of the saapun, is shown in the video of Bogdan Shabanov.

3 additional advice associated with limited chemical resistance of a mixture of gasoline with oil:

  • Do not create an excessive fuel supply. Use freshly prepared fuel mixture. In a maximum of a couple of weeks, she will lose her useful qualities;
  • Prepare as much fuel as it will go to one mowing during the day. At the end of the work, drain the rest from the gas tank and burn the last drops from the fuel canal with a neglected engine;
  • It is especially dangerous to leave the mixture in the gas tank for a long time. winter. In the spring, you will make sure that the engine does not start without cleaning the carburetor (gasoline evaporated, the oil thickened and glued the valve).

In more detail, the technology for eliminating these malfunctions shows in its video video “Chinese lawn mower is not started” Sergey Lesnik. Pay attention to the fuel filter.

To adjust the work of the carburetor allows a special screw, but it is not worth it to twist it without need: the factory adjustment is accurately exhibited. It is better for novice users to contact the service center.

Why is a trimmer not starting for grass (gasoline)?

Why is a trimmer not starting for grass (gasoline)?

Because he worked his. Why, this question may be as many answers. Poor fuel is far from an argument. Maybe a person does not know how to use it, so it starts not correctly. The fuel does not come, the candle is pierced, the wires are pierced, it does not turn on, does not know how to use it, the trimmer for the grass burned/broken, but there are still any other reasons can be. There are still such hooks.

The reasons why the gasoline trimmer for grass does not start can be several.

If the trimmer for the grass does not start or immediately stalls after the launch, then the problem may be in the fuel tank (namely as fuel), in the candle and the ultimate channel, in the air or fuel filter, in the saapon or the exhaust channel.

one). Be sure to check for the grass before starting a trimmer for grass, and most importantly and the quality of the fuel mixture.

2). A trimmer for grass may not start or stall with a flooded candle. It will need to be twisted and wiped.

Dry the channel candle for at least 3040 minutes. Otherwise, a new candle can also burst.

3). If a trimmer for grass starts without an air filter, then it is better to change the old filter for a new.

four). A trimmer for grass may not be started if the fuel filter is polluted.

5). Also, a trimmer for grass may be started due.

Also, the reason may be in the flow of dirt into the exhaust channel or clogging the muffle grid.

A gasoline trimmer for grass may stop starting for several reasons at the same time.

trammer, grass, does, start

Firstly: try to clean the carburetor-its pollution leads to a breakdown of a gas station.

Secondly: vacuum may form in the barrel. If so, try to make a small click in the barrel lid.

Thirdly: roll the correct settings of the trimmer for the grass.

There are several reasons, as a result of which the trimmer for the grass will not start. I will list the main:

  • Poor fuel. For each model of a trimmer for grass you need gasoline with a specific octane number. Roll up with the operating instructions and make sure that you fill in the required.
  • flooded candles. At the same time, I advise you to check the candles for performance. Sometimes even new (in the box) candles can be inoperative or defective.
  • The fuel mixture does not enter the carburetor. Skip it a little.
  • The ignition coil failed.
  • The muffler is clogged. You need to free it from the haze. To do this, carefully disassemble and clean (can be burned on a gas burner).

Typically, the trimmer for the grass did not start after winter and we used to carry almost every spring a trimmer for grass to the workshop, where we were repaired. But, once, a knowledgeable person advised us in.the first, never leave gasoline in trimmer for the winter, because old gasoline may be the reason that the trimmer for the grass will not start, and he also said that the trimmer for the grass for the grass is necessary for the carburetor.fuel mixture. After we began to comply with these rules, our problems with the trimmer disappeared.

First of all, you can see the candle. If necessary, replace it, making sure that the candle is not broken and gives a normal spark. The next problem will be hidden in the fuel system. As mentioned above, check the tightness, then check the fuel filter, if necessary, change. Clean the carburetor, watch the effect. It will be necessary to delve into the ignition system, configure. To check the fuel system, you can pour several grams directly into the cylinder through the candles of the candle, screw the candle and try to start. At least a trimmer for the grass should make the sounds of a running engine within 1-2 seconds and a little smoke should fly out of the silencer.

This is interesting: how to reduce fuel consumption

If you do not start a trimmer for grass at all or immediately stalls after the start of the start, then you first need to look for the reason in the main nodes and units, for this you need to carry out the test in the following sequence, so this sequence: this sequence: this sequence: this sequence:

In these nodes, the whole problem may be consistent.

Useful material from which you will learn how to get a capricious gasoline trimmer for grass that does not want to work!

The summer time has come, and in the personal plots habitually hidden the lawn mower. Great tool, powerful and mobile. Using a gasoline trimmer for grass and grass, you can mow, and get rid of a dried.up weed. However, there are cases that the lawn mower does not start, works with interruptions or without developing full power. Of course, no one is at work! And as they say, you twitch the laborer’s handle more than the mowing.

Difficulties with the launch do not only have the types of motorcycle, but also in new. How to be in this situation? There is only one way out. to listen to the advice of experts and take advantage of their practical experience!

Features of diagnosis

Trammers for grass can be attributed from a technical point of view to complex devices. Based on this, before their operation, it is strongly recommended to carefully study the relevant instruction. However, in practice, many ignore it, often then find themselves in situations where the gasoline trimmer for the grass does not start or is poorly gaining momentum in the process. It is worth noting that you can encounter such problems by purchasing new samples of technology.

One of the most common causes of such symptoms is a long seasonal break in the operation of equipment. In addition, poor.quality and untimely maintenance can lead to extremely negative consequences. It is important to remember that this is relevant for both the Chinese lawn mower and the representatives of the model rows of eminent brands.

The key to effective and operational repair will, of course, be competent diagnostics of the device. In the process of identifying malfunctions, you will have to inspect and test, first of all, key elements. The list of such includes candles, tank, filter nodes and valves of the fuel system. As practice shows, very often the malfunctions of these elements become the reason that the lawn mower does not start. The quality and correctness of the preparation of the fuel mixture deserves special attention, especially when it comes to two.stroke engines. In relation to this parameter, the manufacturer’s recommendations should be clearly followed in order to avoid serious breakdowns and expensive repair work. In the case of, for example, with the Piston Group of ICE, expenses are able to amount to 70 percent of the cost of new equipment.

Often, the owners of the trimmers have to deal with situations when the indicated mixture is high.quality, the carburetor is serviceable and configured, and the device still does not show signs of life when trying to start the engine. In such cases, the condition of the candle should be checked. The following steps will allow to eliminate the problem:

  • turn out the candle;
  • wipe and dry the part (pumping is undesirable);
  • remove fuel and dry the candle channel for 30–40 minutes; Such actions will avoid filling the candle with another attempt to launch;
  • completely eliminate the traces of soot using a file or sandpaper;
  • set the appropriate gap;
  • put the candle in place.

If the candle turned out to be the working and the planting nest is completely dry, and the engine of the braid for the grass is not started, then the thread should be moistened with gasoline. It is worth remembering that regardless of the quality of the issued spark, initially in a completely dry chamber, there will simply be nothing to ignite. Faced with the fact that the spark does not act, it is worth paying attention to checking the contact between high.voltage wiring and candles. If this connection is of high quality, then it will be necessary to check the performance of the ignition control unit unit. In such cases, a qualified specialist is unlikely to do without services.

The next stage in the diagnosis of gasoline braid for grass will be checking the state of filters. Often, the lawn mower is poorly started or does not start at all on the cold due to the fact that the air filter is clogged. This malfunction can be identified by excluding it from the system. If after that the braid for the grass starts, then you will have to clean or change this element. Experienced users strongly recommend periodically blowing an air filter to maximize its operation.

floods a candle on a benzoca

The described tool can also not be started due to problems with the supply of gasoline provoked by fuel filter pollution. For the quick and efficient elimination of such a breakdown, you just need to replace the filter element with a new. It is important to remember that the suction pipe must be equipped with a filter, which is provided for by all instructions. Non.compliance with these rules and recommendations may entail expensive piston repair. In the process of diagnosing and searching for source of problems with the launch of a mower, attention should be paid to the saapun responsible for stabilizing the leveling of pressure in the fuel tank. In addition, it is necessary to check the cleanliness of the exhaust channel and muffler grid. As a rule, such problems are most often encountered during the defect of old models.

Problems with rotation of the cutting canvas

Trimmer’s traction malfunction for grass

On all trimmers of gasoline, a centrifugal clutch is installed, the meaning of which is that the pads, when the speed is added, begin to travel and cling to the cup. The easiest way to check the clutch is to unscrew the bar from the motor, usually 4 bolts. If the pads are pulled, the clutch must be replaced, a metal rattle is heard. If your trimmer provides for a clutch and there is a constant rotation of the fishing line, then the spring is stretched.

Falf in the drive shaft and rod

The main thing to look is: slots on the shaft, connecting the gearbox and clutch cup. Also very often users do not properly insert the rods into the connection, on trimmers with collapsible rods. Be sure to check the integrity of the shaft. If the vibration is present, then plastic bushings are broken. Vibration is very harmful to the vascular apparatus. In order to avoid the melting of the bushings, they must be lubricated and allowed to relax to the mitch.

Production of candles: things that should not be done

The beginning of the new year always inspires people to start new projects, adhere to their New Year’s promises and develop what they may have already begun. If you are a beginner, we hope that your New Year solution was to make high.quality candles. If you have just started studying the manufacture of candles, you probably found that at times it could be caused.

Read Bour from a trimmer for grass with your own hands how to make

In this issue, we will use an unconventional approach and select some things that you should never do in the manufacture of candles if you plan to make the best candles from possible.Some of these bad methods can lead to the creation of a dangerous candle, while others will lead to not the best candle from possible. Some information that we are going to illuminate may seem like common sense if you have some experience in making candles, but for beginners this is not the case or they have not yet encountered our site.

The heating of the candle is facilitated by the use of heat-resistant motor oils for 4-stroke engines, a large wear of compression rings or the entire piston group as a whole.

Diagnostics strategy

Where to start the diagnosis of malfunctions if a trimmer is not started for grass? In situations where the tool stalls immediately after starting, it is worth examining the following units:

It is the breakdown of the above locations that most often leads to the fact that a trimmer for grass is poorly started. If you do not start when it turned out the reason why not her trimmer for grass at once. Let’s look at how to eliminate such troubles.

How to prevent a breakdown during storage?

Lawn mowers are used in the warm season. For the winter they are cleaned in storage in the pantry, closet or garage.

trammer, grass, does, start

Maintenance of the trimmer for grass should be produced several times a year (in t.h. after winter storage) to increase its possible service life

To prevent a tool breakdown, you need to properly prepare it for seasonal storage:

  • Drain the fuel mixture. it must always be drained if you are not planned to use the device within a month, The fuel decays into various heavy fractions over time, which can score the channels of the carburetor;
  • completely disassemble the lawn mower;
  • Rinse, clean and dry all the details to which there is access;
  • inspect all the elements of the trimmer for the grass for damage;
  • eliminate all possible malfunctions, distortions and minor defects;
  • pour a sufficient amount of oil into a gearbox;
  • partially disassemble the engine;
  • Rinse and grease all the necessary elements in t.h. piston;
  • Clean the air filter.

If the lawn mower is stored outside the house and the residential area, it can be wrapped in an oiled fabric. This minimizes the risk of rust on the instrument and increase its life.

Thorough preparation and processing of a trimmer for grass will allow you to keep the device for several seasons without a question.

Conclusions and useful videos

The main reasons why the lawn mower is not started, or starts and stalls immediately:

Why the Chinese lawn mower is not starting: an overview of the main reasons and tips for eliminating breakdowns:

You can carry out a small repair of the trimmer faults for the grass with your own hands at home. Specialized repair services should only be contacted with serious breakdowns, as well as in cases where it is about a very expensive benzos, and its price is not comparable to professional repair.

It is better to fix a cheap trimmer for grass yourself or buy a new one instead.

Your lawn mower has broken and you cannot find the cause of the malfunction? Ask the advice from our experts and more experienced visitors to the site. ask your question in the block for Комментарии и мнения владельцев. Here you can also share personal experience of the lawn mower, add original photos of breakdowns, leave useful recommendations to beginners.

The trimmer for the grass is very hot

Overheating of a trimmer for grass can occur for many reasons:

  • Gasoline has not the same octane number indicated in the instructions for the unit;
  • the proportions of gasoline and oil during the preparation of the fuel mixture are not observed;
  • A mixture of fuel with butter has long been prepared (the mixture cannot be stored for more than 2 weeks);
  • The trimmer for the grass works more than the time instructions;
  • A low.power trimmer for grass on thick and hard grass is used, the device works with overload and quickly heats up;
  • shifted towards the bar or the cassette lid clutched.

The latter happens if you install the mowing head inappropriate for this unit

, or when the axis shifts inside the bar. These changes make it difficult to rotate, the load on the engine increases, and it overheating.

A large assortment of and components at affordable prices

The assortment of the Kosi Spit for Grass store has a huge selection of specialized products designed to perform work or support important functions of working tools. So, depending on the requests of the buyer, the online catalog offers to choose:

  • Tools:
      Modern lawn mowers of grades GoodLuck, Baikal, Carpathians and other manufacturers;
  • gasoline saws with the selection of power and sawing parameters.
  • Spare parts:
      professional spare parts for the chainsaw of the Chinese release and the CIS countries;
  • high.quality spare parts for benzos;
  • Spare parts for electric saw and other assortment.
  • Components:
      accessories for gasoline cos;
  • original candles;
  • guide tire for a chainsaw of the required length;
  • knives for benzos;
  • files for the chain;
  • Lubrication for motorcycle and oil for nonsense of the desired consistency, depending on the nodes of use.

If necessary, a benzo.tool to buy online, each spare part is equipped with a link to the consumer basket, which simplifies the order process a lot. The manager’s phones that are able to answer questions are also available, to tell what spare parts are available now, how quickly the collection and delivery to the buyer are performed, and also help to choose the necessary elements and order them in the right amount. “Spit for grass” is a modern online store where you can buy spare parts for a chainsaw or lawn mower at an affordable cost.

Why does a gasoline trimmer for grass do not develop momentum?

low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture; The grass was wound on the shaft of the fishing/knife head; clogging of the air filter/muffler; Balance of the carburetor.

  • Dial in a cap made of PET bucks or in a syringe of 20 grams of fuel
  • Pour it into the combustion chamber through the candle hole
  • Twist the spark plug
  • Put on a candlestick and start the engine

Why the trimmer does not start for grass is a spark?

If there is a spark on the candle, but the trimmer for the grass does not start, then the reason is the supply of the fuel mixture in the combustion chamber. To make sure this, you should perform the following actions:. Pour it into the combustion chamber through the candle hole tighten the spark plug

the quality of the components of the fuel has changed (the octane number of gasoline and the brand of oil); The air temperature and its vacuum (height, heat, coolness, frost) have changed very much; The beginning of the operating season of a trimmer for Husqvarna grass (first May, after winter storage);

Maintenance and prevention of launch problems

So that the tool serves longer and does not create problems, keep it clean and regularly maintain.

Do not store the refueling lawn mower: leaving it for more than 2 weeks, and even more so for the winter, drain the remaining fuel from the tank, then start the motor and let it work until it stalls yourself. Leaving the tool for the winter in the barn, wrap the motor and knives with an oiled rag.

For lubrication of a 2.stroke motor before storage, unscrew the candle and raise the piston with the starter to the very top. Drip a little motor oil from the syringe and use the starter several times cranks.

In the spring, before the first use after downtime, it is advisable to check the candle and filters, disassemble and rinse the carburetor, even if there are no problems with the launch.

Conclusions and useful videos

For clarity, we offer a video with the analysis of common problems:

To check the carburetor or if you decide to change the oil seal yourself, it will come in handy

trammer, grass, does, start

Dismantling and cleaning the carburetor is described in sufficient detail here:

If your lawn mower does not start, do not rush to look for a master to repair it. It is possible to independently find and eliminate the cause not only much cheaper, but also faster and easier.

Most trimmers are arranged almost identical, the structure of small details may differ and, of course, the quality of their performance. Use and store your tool carefully, do not spare money for fuels and lubricants and time for minimal service, and the trimmer for the grass will become a trouble-free assistant for many years.

Did you have to face a situation where the lawn mower stopped starting? How did you fix the situation? Share your opinion and experience in the Комментарии и мнения владельцев below!