Trimmer for grass for grass stalls after heating. Carburetor adjustment and configuration

The reasons for the fall in the motorcycle. The lawn mower does not develop full power

Any person owning a country or land plot is well aware of the problems of the fight against excess vegetation. Now a trimmer for the grass has come to the rescue, which successfully replaced the usual braid in this field. This unit is very convenient in work, but it, like any mechanism, also, due to difficult working conditions or incorrect operation, is characterized by failing. Situations are quite common when a trimmer for grass does not gain momentum. To understand this problem, it is necessary to understand some aspects related to the functioning of the device.

All trimmers for grass are classified according to the type of power: gasoline or electricity (from the network or battery). It should be noted that gasoline mowers in many respects exceed their electric and battery analogues. Despite the fact that they all perform similar functions, the difference in performance, maneuverability and effectiveness is very noticeable. However, the general principle of operation of all types of manual braids is almost no different- the devices are equipped with engines (two- or four-stroke ICE or electric motors), which drive the cutting unit (reel with fishing line or metal disk). All elements are fixed on the line of straight or curved shape, including the handle for controlling the trimmer on which the main buttons are located.

Since the problem of weak revolutions is more characteristic of gasoline trimmers, they will be given more attention. So, the lawn mower is very comfortable in work and unpretentious in maintenance. over, most of its malfunctions are caused by ignorance by the user of elementary things, which are written in the instructions. Therefore, before starting the operation of the unit, it is necessary to carefully study the management of the manufacturer. In particular, in order to start the engine, it is necessary to do the following sequential actions:

• turn on the ignition button;
• press the silicone button for pumping gasoline several times;
• close the air damper;
• The gas lever is installed in a position for high speeds;
• first make non.leaf with the starter handle to feel the engine resistance, then jerk sharply.

If the lawn mower started up, but stalled, you need to put the air damper in the middle position and repeat the attempt. When the engine works, you need to slow the gas and open the air damper, since the trimmer for the grass functions only on the leak.

Important! The mode of operation of the trimmer for the grass depends on the various environmental influences. In hot weather, the unit should be given more time to cool. When working in conditions of dense thickets or high vegetation, the engine also overheats strongly. It is necessary to take five-minute breaks every 15-20 minutes.

The reasons for the weak.speed trimmer for grass

If users complain to the trimmer for grass, which does not gain momentum, this means that it works normally on idle, and when pressing gas does not develop the necessary power. This can happen as a result of a long downtime of the apparatus without activity. These problems are typical for gasoline devices, including the Husqvarna 128R, STIHL FS 38 and Hitachi different modifications.

Working with a trimmer, you need to monitor its behavior all the time. a drop in revolutions and unusual noises signal the malfunctions in the aggregate. Sometimes you give gas, and the trimmer for the grass swims. In such cases, the work should immediately be suspended, let the mechanism cool and start searching for possible problems. They can be of a different nature of both the technological plan and external factors related to the conditions and features of the operation of the device.

External factors

Several factors that are not related to its breakdown affect the reduction of revolutions:

• filter pollution due to the hit of particles of dirt and dust in it;
• use of poor.quality fuel;
• incorrectly prepared mixture (relevant for trimmers with two.stroke gasoline engines);
• pollution of the muffle of muffler particles of vegetation, soil elements and other objects.

In this case, in the second and third cases, the formation of a soil in the combustion chamber is formed, and the elements of the carburetor are clogged.

technical issues

The technical problems of the lawn mower mainly occur in the fuel and ignition system. You can cope with them yourself.

• Когда ручная косилка не заводится или глохнет, проблема может быть связана со свечой. The dark cargo speaks of poor carburetor adjustment and low gasoline quality.
• The reason for the incorrect operation of the trimmer for the grass may be clogged fuel hose. Filters are also often clogged.
• Another internal problem. the muffler is covered with soot. From this, the turnover of the grass for the grass falls strongly. Output. you need to clean the muffler.

Important! If the unit does not work due to breaking up the engine, serious problems may occur. In this case, the malfunctions that can be eliminated with your own hands include only the destruction of piston rings. With more serious problems with the motor, if there is no warranty, you should be prepared to visit the workshop.

The lawn mower stalls when you press the gas

The gas mushroom gas key

As practice shows, in most cases, the cause of engine stopping is the dumping of the carburetor associated with long.term storage or operation of the tool in an aggressive environment (temperature changes, high humidity, dustiness), high loads or wear of individual parts. The characteristic signs of the need to configure the carburetor include increased vibration. If you have experience in repairing the fuel system of gasoline engines, you can eliminate the problem without any problems, otherwise you can familiarize yourself with the detailed instructions for setting up the carburetor.

The hole in the fuel cover (saepun) of a trimmer for grass

The second of the possible reasons why the trimmer for the grass stalls when pressed on gas is blocking the hole in the lid of the fuel tank (sapuna). If small particles of dust, the remnants of grass and sand gets into it, a vacuum is created in a gas tank, as a result of which the fuel ceases to enter the carburetor. You can clean the benzotrimmer’s saapun with a conventional sewing needle and subsequent blowing with compressed air. Experts recommend when completing the work once a few mowing to clean the cabin. If it is not possible to clean the lid, it is necessary to replace.

Fuel valve of the lawn mower

With a similar problem, it is worth paying attention to the fuel valve, which, when clogging, ceases to normally pass the fuel mixture. By solving this malfunction, it is weakening using a suitable tool. In addition, the problem with the circulation of the fuel mixture may cover in the contamination of the valve. To do this, just blow it with a stream of compressed air.

Trimmer malfunctions for grass

Trimmer for grass is a convenient and affordable replacement for the lawnical mower. Its cutting part is made in the form of fishing line, knives or disk installed on the drum, which is closed on top of the protective casing. The basis of the design is a bar, which is adjustable in height, at the end there is a comfortable handle and shoulder belt.

Like any other technique, a trimmer for grass may be unknown, and so that the breakdown does not lead to the final failure of the tool, we suggest you familiarize yourself with this article. Unit can break down for various reasons. Breakage occurs both in new trimmers and those that have long been operated.

A malfunction of electrical models

The reasons for the unexpected shutdown of an electric lawn mower are associated with a cliff of the cord or the absence of current. In the first case, it is recommended to check the cable for a cliff. To replace the power cord, you need to pull out the fork out of the outlet, open and dismantle the circuit lid.

Before unscrewing the squeezing of the cable? It is necessary to remember the diagram of its connection to the switch. To disconnect the cord, a hexagon is used (diameter 1 mm). The clip is released, the conductors are dismantled. To check the cable for a cliff, multimeter is used. If necessary, a new cord is installed. In this case, the reverse sequence is observed.

In the second case, it is recommended to connect another device to the mains. Electric devices may not work when the fuse is damaged in the fork. To carry out repair work, you will need to disassemble the fork. For this, a screwdriver and a tester are used.

Motor malfunctions occur when overheating of the lawn mower:

In the first case, it is recommended to wait a few minutes so that the motor cools. In the second case, you need to remove the stuck object. The effectiveness of the cooling system depends on the state of the air filter.

Dirty device poorly passes air, which helps to turn off the device. Experts advise cleaning and changing the filter once every 3 months (with constant operation of the lawn mower).

With a breakdown of the electric motor, the corresponding smell and noise appear. In this case, you need to replace the drive.

The vibration of the motor on idle, on a cold or warm engine: possible causes

Immediately note that there are many reasons for the emergence of vibration of the internal combustion engine, starting from the torn engine pillows (supports) and ending with ignition passes and the tag of power unit. For a more accurate definition, first of all, you should pay attention to one or other symptoms.

The fact is that vibration can be either constant (regardless of heating and loads on the unit), and manifest itself in a certain mode of operation (idle or high speeds, on cold or hot). Another engine vibration can manifest itself on a cold ICE, but as it warms up, it completely disappears. Let’s understand.

• For example, if the engine was recently versed for repair (possibly capital), then there is a high probability that the crankshaft was not properly covered after the reverse assembly. The result is a beating and increased vibrations.
• We also note that after repairing the motor to imbalance and vibrations, different weights can lead to the details of the cylinder-piston group. The more weight difference turns out, the stronger the vibrations will be. For this reason, experienced craftsmen weigh pistons, fingers, etc.D.
• Often the reason for vibrations is that the engine is troit, that is, one or more cylinders for any reason do not work or work with failures. As a rule, the elimination of the cause of the touch automatically eliminates the presence of vibrations of the power plant.
• Do not forget that the timing belt incorrectly set on the marks or the chain also causes vibrations.The reason is that the engine works unstable due to violation of the phases of gas distribution.
• Many engines have in their design special balancing shafts that are necessary in order to “extinguish” fluctuations. Quite obvious, problems with these shafts will lead to an increase in the vibrations of the motor.

The engine pillows are one of the most common reasons why the engine vibrates. In fact, this is a damper made on many cars from rubber to absorb vibrations. As you know, over time, the rubber daggers and cracks, loses its properties as a result of technical fluids and t.D. The main thing is that the engine with a damaged pillow cannot work softly.

• If you recently moved from one car to another, it should be borne in mind that different engines may differ in vibration loads. The number of cylinders, layout and a number of other features affect the level of vibrations. In simple words, the usual in-line engine for 6 cylinders can operate with less vibrations than a 4-cylinder and, especially, 3-cylinder engine. over, in this case, we are not talking about problems, since for a particular ICE a certain level of vibration can be considered the norm.
• We also add to reduce vibrations, on the crankshaft of many engines there is the so.called dignified damp. If problems arise with the element, the motor will begin to vibrate more strongly.

As you can see, at the initial stage it is important to accurately determine the cause of the strengthening of vibrations. For example, in most cases, it is enough to replace the engine support or solve the problem on which the engine is troit. However, it also happens that the power unit itself needs to be disassembled and repaired.

Repair of mechanical braids is carried out when the cutting elements are blown up or damaged. In this case, experts recommend to independently dismantle removable knives. Evadal is used to sharpen them. If necessary, the battery is replaced in battery.

Before repairing the lawn mower, the type of motor is determined:

Features of diagnosis

A well.posed question is already half the answer.The fact that the gasoline trimmer for the grass or the lawn mower stalls, namely, will significantly accelerate the search for a solution

• immediately after the start;
• when it works for some time idle. after one or several minutes;
• when pressing the gas button (or handle). or shortly after the start of work at high, submasymal speeds;
• under a reinforced load (for example, to cut the bushes, mow thick and high booths);
• when warming up in the cold, it heats out excessively (the lawn mower stalled around overheating);
• After the opening of the air damper.

If stalled under load

Sometimes a trimmer for grass stalls under load, as it cannot gain momentum. This means that the cable stretched in the carburetor is weakened and sagging. If there is experience in repairing this node, the cable should be pulled.

Another cause of the malfunction. the fuel hose is stretched overly. With a load, it is even more stretched, as a result of which cracks are formed, as a result, the part deteriorates. To eliminate the breakdown, you need to replace this element.

What could break

Problems with a benzocosa associated with the fact that this device is not started, specially classified by specialists of service services. They stand out malfunctions with subsequent nodes of the mechanism:

• the engine, in which the piston and bearings can be worn out or out of order, crack the crankcase;
• the fuel supply system, with all this, can be clogging the filter or tasks with a carburetor;
• mechanical damage to wires, tubes, hoses;
• The ignition chain.

In order to correctly find the knot where the breakdown occurred, you need to direct attention to the circumstances of the trimmer stalls for the grass.

Diagnosis and elimination of electric motor problems

Electrimmer malfunctions can be as follows:

To cope with these breakdowns, you do not need to disassemble the entire device.

With serious engine failures, you will have to disassemble it. To do this, you need to unscrew a few screws. Having gained access to the motor details, you need to carry out the following actions:

• Checking the degree of worn in brushes. unsuitable details will need to be replaced with new ones;
• Rall the engine winding. the resistance should be high;
• Check the stator and rotor. to test the rotor winding with a multimeter, measure the resistance: large deviations from the norm indicate a malfunction, the absence of resistance on the stator winding also indicates a breakdown (the same way is diagnosed with the stator case).

Low.speed problems are a common phenomenon for cheap trimmers. However, with improper maintenance, such manual mowers as Huter, Patriot 3055, Echo also suffer from this.

The trimmer for the grass is not started due to the malfunction of the carburetor

One of the most difficult reasons for the impossibility of launching a lawn mower is a carburetor. This mechanism is responsible for the preparation and good supply of the fuel-air mixture to the cylinder. If the carburetor is clogged or adjusted incorrectly, then the lawn mower may not start or work unstable. Detailed instructions on how to adjust the carburetor on a benzocosa is described in this material.

If the adjustment does not help restore the stable operation of the tool engine, or the trimmer for the grass does not start at all, then the carburetor should be removed and repair it. The entire repair of the carburetor is that you need to disassemble it, clean all channels and constituent elements. If necessary, replace the failed details. membranes, filters, etc.P.

If the suspicions fell on the carburetor, then you should pay attention to the following types of malfunctions:

• Canals and nozzles clogged. special liquids can be used for cleaning, however, it is best to disassemble the mechanism with its thorough flushing. The reason for the clogging of the channels and jackets of the carburetor is the storage of a tool with fuel in the tank
• Wear of the carburetor gaskets. rubber seals contribute to the fact that the tightness of the mechanism is disturbed, as a result of which the serviceability of the functioning is violated
• Memory of carburetor membranes. they are responsible for downloading fuel to the device

To make sure the CPG malfunction, you should check the compression, which is described above.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

• Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
• A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
• The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
• Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
• Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

• First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
• Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
• Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
• Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.
• If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
• After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

• completely drain the fuel;
• disassemble the lawn mower, wash and clean all available components;

• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

The lawn mower stalls when you press the gas

The hole in the fuel cover (saepun) of a trimmer for grass

With a similar problem, it is worth paying attention to the fuel valve, which, when clogging, ceases to normally pass the fuel mixture. By solving this malfunction, it is weakening using a suitable tool. In addition, the problem with the circulation of the fuel mixture may cover in the contamination of the valve. To do this, just blow it with a stream of compressed air.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Another possible reason for the breakdown is the malfunction of the carburetor dosage system. To eliminate this problem, it is better to contact professionals.

Immediately after you started

The unit may stall immediately after starting, if the carburetor is shifted or incorrectly adjusted. This causes an uneven supply of fuel. As a result, the device vibrates clearly. To eliminate defects, the carburetor is reconfigured, following the annotations to the mechanism.

Apart from that, the engine stops when clogging the fuel supply valve. In such cases, it is quite easy to clean it. If the bureau at first earned, but later stalled immediately, then maybe the fuel with some difficulty falls into the carburetor knot. Weakening of the valve helps to solve the issue, which ensures free circulation of the consistency in the system.

The stop can also be caused by air leaks in the presence of mechanical damage to the hose (holes, cracks), taking fuel. In this case, increase the speed of the drive in order to resign more air from the system from the system.

Malfunctions leading to improper operation of the chainsaw

There are a number of malfunctions that must be taken into account in diagnosis, t. to. They can lead to the interruptions of the saw.

• Damage to the crankshaft bearings. With worn crankshaft bearings, the appearance of a beating on the main shaft is inevitable, where the flywheel is attached. In such a situation, it is impossible to adjust the gap between the flywheel and the ignition coil, which entails interruptions in sparking, and unstable work of the chainsaw.
• Pollution of the pulse channel. The pulse channel serves to ensure the operation of the fuel pump, respectively, its pollution leads to improper operation of the pump, which will make it impossible to operate the saw (it will be launched and immediately stall).
• Wear of the CPG. As a rule, with increased wear of CPH, a decrease in compression in the chainsaw engine is observed, which is necessarily affecting its ability to develop momentum.
• Fuel and air filters pollution.

At idle

At single speeds, the common reasons for stopping a trimmer for grass are as follows:

• reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel mixture;
• clogging of the throttle;

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

At high speeds

The hole in the fuel cover (saepun) of a trimmer for grass

With a similar problem, it is worth paying attention to the fuel valve, which, when clogging, ceases to normally pass the fuel mixture. By solving this malfunction, it is weakening using a suitable tool

In addition, the problem with the circulation of the fuel mixture may cover in the contamination of the valve. To do this, just blow it with a stream of compressed air.

• etching of atmospheric air into the combustion chamber;
• problems with the circulation of a mixture of fuel;
• clogging the saapun in the lid of the fuel tank (cleaning the hole with a thin sewing needle);
• Incorrect carburetor adjustment.

When air sunses, when I operate ICE, it is necessary to check the tightness of the pipes and the integrity of the gaskets in the CPG. The problem with the circulation of the fuel mixture can be solved by the elimination of blockages in the fuel pipes leading to the carburetor. If a vacuum occurs in the tank and not receipt of the fuel mixture to the carburetor, it is enough to clean the soundtress with a thin needle and blow it with air.

If the lawn mower stops when pressing the gas, then the reasons may be the following.

• The most common option is a fuss of adjusting the carburetor, which occurs with significant loads on the drive, after a prolonged inaction of the mechanism or when it is used in severe conditions.
• The clogging of the fuel valve, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. Also, a tensile of the fuel hose can occur up to its rupture, caused by the action of a significant load.
• Clogging of the saapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

When a braid for grass stalls at high speeds, this is due to the following problems:

• clogging or clutching a valve located on the gas tank lid;
• The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
• problems with the circulation of the fuel mixture;
• atmospheric air
• The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

• a clogged air damper;
• The clogged filter is fuel, and when you give gas, this is especially noticeable;
• the air of the crankshaft shaft occurs;
• damaged gasket between the cylinder and the carb.

When you cleared, washed and blowing the elements, but again the lawn mower stall when you press the gas-replace them with new ones, check the quality of the fuel, as well as the literacy of the proportions of the cooked mixture. When opening the air damper, the tool will stall for the following reasons:

• Dosage carburetor.
• The appearance of cracks on the fuel hose caused air leaks.
• The occurrence of problems with the oil seals.

Read more: The best robots-vacuum cleaners of 2021: 10 flagship ratings

In the process, situations arise when the lawn mower at high speeds is subject to a similar sharp stop. It occurs for the following reasons:

• due to problems with the circulation of the fuel mixture;
• with air leaks;
• The fuel intake hose is poorly connected or cracked and cannot be used;
• stab or clogged the valve of the cover of the gasoline tank;
• The carburetor was resolved.

What in the end

It is worth noting that the inconsistency of the idle move on the engine with the injector is diagnosed by the method of checking the main systems that are responsible for the flow of air in the internal combustion engine, also a change in the composition of the consistency, taking into account the number of incoming air. It turns out that it should also be taken into account that the failure of individual sensors of the ESUD can lead to an increase or floating turnover of xx.

The lawn mower stalls at high speeds

Perhaps a more common complaint associated with gasoline trimmers sounds like this: the lawn mower stalls.

Naturally, a rather formidable malfunction may be a prerequisite for this. How to adjust the carburetor at idle does not work. On the Forward Boistorose, even at idle (the benzotrimmer shaft always turns even on. The lawn mower stalls at idle. The Benzotrimmer system and the lawn mower system does not work. But almost always the situation is even easier than it seems in the 1st look.

To cope with such an inconsistency, at first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and at times it is even self.destructive.

In fact, events are when the lawn mower stalls at high speeds, there are quite a lot of these events.

Another is the presence of flaws in the power system.

In this case, the lawn mower will stall at idle. For what reasons Stihl 100 eighty stalls idle or complete gas at least some kind of tool can break and the Stihl MS 100 chainsaw is not an exception. The lawn mower does not work at idle. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

If the chainsaw of STIHL MS 100 eighty stalls at idle, does not gain power when pressed on gas or completely stalled at full speed, you need to diagnose the fuel system and inspect the crankcase for density. You can do this without the help of others, but you need to have certain abilities. If you are not familiar with two.stroke saws, it is better to turn to specialists, t. To. This technique is quite capricious and any errors are expensive.

The lawn mower stalls at high speeds

Perhaps a more common complaint associated with gasoline trimmers sounds like this: the lawn mower stalls.

Naturally, a rather formidable malfunction may be a prerequisite for this. I can’t get a trimmer for grass why when working a motor for but saw, with all this, it does not revolve? It works only when it is worth opening its trimmer for the grass does not work right away. On the suction. It works only when opening an air damper for one mm I do not think that a trimmer for grass but. But almost always the situation is even easier than it seems in the 1st look.

To cope with such an inconsistency, at first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and at times it is even self.destructive.

In fact, events are when the lawn mower stalls at huge turns, there are quite a lot of these events.

Another is the presence of flaws in the power system.

In this case, the lawn mower will stall at idle. Works only at idle. trimmer for grass actually new. This may be exclusively in case I can’t start a trimmer for grass Craton works on a sucker. Stalls, mm for two. And she doesn’t work. If the engine at idle why the motor works. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Why does the lawn mower stall when you press the gas: the causes and their solutions. The lawn mower stalls (trimmer for grass): on idle.

• Idle sensor failure;
• Clogging of the throttle;
• The failure of the throttle position sensor;
• Injector or carburetor pollution

The grounds for breakdown can be completely different, therefore, when eliminating them, it will be necessary to operate with all kinds of actions and techniques. If your shoulders are considerable driver’s experience, and you know the features of the car’s work as your five fingers, regardless of the model, then the elimination of this kind of malfunctions will not cause you any problems. And all because such breakdowns are not complex or serious. It follows that you can establish the operation of the car without outside help. Well, if the level of awareness or lack of free time will not give you the opportunity to eliminate all defects yourself, it is better to seek help from knowledgeable people who can save you from unpleasant moments in the shortest possible time.