Trimmer for grass gasoline how to put a disk. Why is the ignition adjustment

STIHL trimmer for grass how to install a spit.head

The replacement of the disk on the trimmer will need to be carried out regularly with frequent use of a gas station. Even good knives dull over time, you need to hide them or install new. In practice, plastic and metal discs are used that have a different number of blades, sharpened in different ways. The procedure for replacing it does not depend on this. In the process, an important point is the observance of safety precautions. If the material of the cutting part of the tool allows, then you can independently sharpen, which will save money.

A trimmer for grass with a knife installed on it is most conveniently used for a more comfortable mowing of high and loaded grass in the country. a fishing line for a trimmer on a motorcycle in such cases does not cope. Thin torn very quickly. Using Tolstoy 2.3 mm cord or homemade rods with cables forces the vegetation to wind up on the rogue. This increases the load on the engine. As a result, the piston group and other mobile units of the unit wear out very quickly.

If the mowing of a weeds is produced by an electric trimmer without a knife, only with a fishing line, even a thick with a figure section, the problem cannot be solved. There is always a risk of overheating the electric motor and disable flexible shaft. And it’s all in a large torque of the electric motor. The grass wound on a spindle creates strong resistance to the shaft resembling a speedometer cable that does not withstand and twist.

In order to protect the equipment from premature wear, manufacturers have provided the ability to install special knives on the grass for grass for grass. The design and shape of existing cutting elements allows you to easily cope not only with coarse and outgrown with grass, but also to successfully fight the young shrub.

What knives to put on an electric and a lawn mower

Before buying and putting a knife on a motorcycle, find out what they are and in what cases are used. Today, manufacturers offer the consumer a large number of types of these supplies. In general, the entire cutting tool designed for mowing grass can be classified:

The main material for the manufacture of trimmer knives can be plastic or metal. The use of such consumables largely depends on two parameters:

For safety reasons, manufacturers do not recommend putting steel knives on electric trimmers for grass. Almost all motokos operating from the electric network and battery are equipped with plastic blades. Depending on the manufacturer, they can be a solid disk design, with several blades or in the form of a special mowing head, which provides for the installation of removable plastic blades.

Direct rod in a gasoline trimmer for grass and curved in electric

Putting a metal knife on an electric trimmer for grass does not allow its design features.

• The curved rod of the unit reduces the distance from its working part to the legs of the Kosar. In the case of a collision of blades with a stone or other hard object of a braid for grass, it is discarded to the legs.
• The high torque, which we mentioned above, in the event of a collision of a metal knife with a solid object, transfers a large load to the flexible shaft of a trimmer for grass and its engine. What causes their premature failure.
• Handle Electric Knules most often does not have a restrictive bar playing the role of the stop. Which does not exclude leg injury.

It is these features that allow the use of exclusively plastic knives on trimmers with electric engines. In a collision with an obstacle, the blades are destroyed, thereby protecting the legs of the mower from obtaining possible injuries.

Plastic knives cope well with outgrown and dry grass. They can mow the nettles and stems of burdocks.

The use of metal knives only on gasoline trimmers is also due to constructive features.

• The direct design of the rod increases the distance to the legs, which provides the Cossacks with complete safety.
• Comfortable U-shaped and J-shaped handles allow you to keep the tool firmly. D-shaped handles Motokos are equipped with a limiter resting in the leg of the Costsa, which does not allow to let the head to the legs when meeting a cutting disk with a solid obstacle.
• The clutch of the gasoline engine allows you to smoothly gain speed to the optimal level. And when the blade collides against a hard surface, it can extinguish part of the blow.

Instructions for replacing a disk on a gas tank with a step.by.step description

Having sorted out the design of the cutting knives, it remains to find out the process of replacing them and installation on the tool. If there is a head with a fishing line on a gas station, and it is planned to install a metal disk, then no remodeling of the structure will be needed.

To install a metal disk on a trimmer for grass, the following instructions must be followed:

• First, a plastic protective casing is removed. it is not necessary. Depending on the model of the tool, the dismantling process may differ. If the trimmer has a metal casing, then it is not necessary to remove it. Removing a plastic casing is performed in order to install a metal
• Using a special key-player or screwdriver, it is necessary to block the gearbox. The shaft blocking hole can be located on the side or on the end side
• A mowing head or spool is twisted from the tool if they are installed
• A disk is installed in the place of the head or spray. The internal diameter of the disk should be in a special groove. The nozzle is installed so that the front side (with letters) looks upward
• After installing the disk, a fixing washer of the corresponding size is placed. After that, the mounting nut is screwed, having previously blocked the gear shaft. Direction for screwing the fastener. counterclockwise
• After completion of work, it is necessary to install a protective metal casing. If it is not, you should leave a plastic casing

As you can see, the procedure for replacing the disk on the trimmer is not at all difficult, and takes no more than 5 minutes in time. Below the video shows how to properly change the mowing heads and circles on benzocoses.

Disk selection criteria

You need to choose a plastic or metal knife, given the area of ​​the site that is planned to be processed, as well as the type of trimmer for grass is electric or gasoline. The number of blades will depend on which shoots must be removed using the tool. Choose the desired disk shape, the number of blades and manufacturing material can be using the instructions for the operation of the device. It usually prescribes which mills are recommended to use to solve certain problems.

Characteristics

• Engine type: gasoline.
• Power: 1500 W.
• Power: 2 l.With.
• Engine volume: 52 cubic meters. cm.
• Engine Applicity: 2.
• Type of cutting element: fishing line for trimmer, knife.
• Revolutions: 9500 rpm.
• Fuel tank volume: 0.7 l.
• Handle shape: U-shaped (bicycle).
• Speasing width: 25.5 cm.
• Length: 35 cm.
• Width: 23 cm.
• Height: 166 cm.
• Weight: 6 kg.
• Warranty: 12 months.

Motokos nozzles make a trimmer for grass can be a multifunctional unit

The lawn mower has always been an integral tool in the care of the lawn, both for ordinary people and for utilities. over, with its help you can even harvest hay for pets, cut grass in farm plots or use potatoes for weeding potatoes.

Due to the presence of many diverse nozzles, the user has the opportunity to reveal the functional potential of the unit and turn it into a “universal soldier” that will save money, effort and time.

We get acquainted with the types of nozzles on Motokos

It should be noted that many specialized stores offer a wide variety of nozzles. But they are suitable only for models with a collapsible bar, because to install the addition should be removed the main head and put another one in its place.

Each of the listed tools should get to know a little closer and understand the design features and specifics of the tasks performed.

Highway: Features

With its help, a person can get rid of branches and branches that grow at a three.meter height. Structural features allow the object to perform such operations, because the nozzle of altitude on the motorcycle toss consists of a one and a half meter rod, supplemented by a chain or tire.

In most cases, the width of the chain does not exceed 1-3 mm, and a weight of 2.5 kg is comfortable for long-term operation allows a person to actively operate the unit and not feel pain in the back or shoulders.

It is worth noting that due to the nozzle of a bitch for the lawn mower, you can get to small branches located at an altitude of up to 4.5 m. The only difference between the altitores and the bitch is that the first option works on the principle of a chainsaw, and the second according to the principle of a hacksaw.

As for homemade options for the indicated device, there is no need for their creation, because in stores such nozzles are very democratic and almost everyone can afford to buy them.

The handler of the edges of the lawns

In principle, this device is very similar to the standard nozzle of motorcycles, but the main difference lurks in a more curved rod. With its help, the operator can get to the most remote and inaccessible places for the cut of grass.

In most cases, the specified tool is equipped with a special fishing line supply system. It is thanks to this system that you can most accurately determine the width of the processed territory. The weight of the addition of this plan is 2.7 kg.

Cultivator nozzles

With the help of the indicated nozzle on a motorcycle for cultivation, a person can easily process small plots of land. Additions of a toothed or drum plan are used to loosen soil near trees, the process of digging flower beds and the garden, hilling potatoes, carrots, etc. P.

Often objects are equipped with several reliable cutting details. They use a bar with a diameter of about 25 mm, contributing to a high level of endurance.The nozzles also have a setting width of the gripping cutter (130-250mm).

Types of cultivator nozzles for a trimmer for grass

Today, the market has 2 types of cultivator nozzles for benzos:

• Disk. Options are equipped with several discs with fixed knives. over, the ends of these same blades are curved in a certain direction. A special protective damper is installed on them on top of them, allowing the Earth not to fly out during the work process;
• Toemed. This type of cultivators for a trimmer for grass consists of a straight row of several curved pointed knives that turn the ground and open it. The object is quite heavy, because in some cases its weight can reach 5 kg.

It is worth noting that the nozzle of the milling cutter on Motokos will not allow the blades close to the soil, because the bar is a lot of spring, and excessive pressure can cause bending and breakdown of the bar. over, experts do not recommend using a cultivator for motorcycles on clay soil, because it will not be able to penetrate deeper, but it will only scratch the surface.

DIY

It is also a lot that is also pleased that in modern conditions it is not so difficult to create a nozzle for weeding on a motorcycle with your own hands. The main thing is careful to watch the talked videos and follow the advice of people who really managed to construct a home.made assistant based on an electric or gasoline unit.

Instructions with a step.by.step description how to wind the coil of a trimmer for grass and lawn mower

In order not to make a mistake with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the coil. This information is usually presented on a tip, which will not allow us to make a mistake using the appropriate equipment.

If the information on the coil about what diameter the fishing line for the trimmer can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the equipment, it remains to figure out how to charge it. There are two ways for this, but not for all they are applicable. Consider both methods in details, and already depending on what models and trimmers you use, you are determined on your own which option is suitable.

It is interesting!The principle of how to wind a fishing line for a trimmer for a tip of motorcycles is appropriate not only for autonomous benzar groups, but also for electric trimmers.

How to check the serviceability of magneto

Magneto is the main detail in the engine ignition system and is a coil with primary and secondary windings located around the core. Often, due to the malfunction of Magneto, the spark on the spark plug disappears, and the fuel ignition does not occur. To check the coil, you will need to use the tester, and perform the following actions.

• On the tester, going into the resistance measurement mode, you need to set 200 Ohms. In this way, the primary winding will be checked.
• Connect one tester electrode to the “mass” of the coil, and the second. to the contact emerging from the magneto. Normally, resistance should be from 0.4 to 2 ohms.
• To check the secondary winding, you need to install the device switch for 20 kOhm. Further, one probe of the device is inserted into the cap of the candle, and the second is connected to the “mass”. Normally, resistance indicators should be in the range from 4-6 kOhm and above (depending on the model).

When a circuit is broken, the device will show infinity, and when close. 0 (zero).

If you do not have a tester, then you can use the following way, showing more accuracy so that the electrode does not touch the cylinder, otherwise the coil will burn out.

• Remove the cap from the candle. You do not need to twist the candle to save compression.
• You need to insert a nail without a hat into the cap. The nail should be of such a diameter to hold well in the cap.
• Tie the cap with a nail to the cylinder using the dielectric, so that the gap between the electrode and the cylinder body is in the range from 5.5 to 7 mm (but in no case touch the “mass”).
• Using the starter, make an imitation of engine starting several times. The ignition button should be enabled.
• Watch whether the spark appears and what color it has.

Normally, the spark should be strong, white or have a bluish tint. If the spark is weak, and its color is orange or yellow. this indicates a faulty magneto.

It should also be taken into account the fact that sometimes Magneto in a cold state can give a good spark. But after heating due to internal malfunctions, the current ceases to produce. As soon as the coil cools, the trimmer for the grass starts again and works for some time until Magneto heats up again. Such a reel must be replaced.

Sometimes a similar problem with heating can cause a spark plug, even if the coil is serviceable, so you need to check both parts.

The advantages of trimmer disks compared to the fishing line

Trimmer disk compared to the cord, has its advantages. You need to know these advantages in order to decide in the end whether to buy and use metal cutting knives. Consider all the advantages of the trimmer disks:

• The ability to cope with different vegetation, unlike fishing line. It can be dry, long and thick.nisted grass, and even small vegetation. The fishing line for a trimmer hardly copes with medium.sized grass, and it is not able to cut off thick.stubble grass. The cord will either get confused for the grass, or the fishing line for the trimmer will wear out quickly, which is not at all rational
• High speed achievement of the result. Unlike fishing line, the disk cuts grass with qualitatively (with good sharpening), without leaving “roosters”, therefore, a mowing trimmer with a metal circle occurs faster than when using the cord
• Discs do not wear out, unlike the cord. The cutting knives or parts of the circle are blunted, but the issue is resolved by hiding. How to sharpen a trimmer metal circle described in the material below. With prolonged operation, the cutting devices are abrasion, but they are enough for at least 3-5 years
• A long service life, in contrast to the fishing line, which is associated with the design of the equipment

There are also disadvantages of the considered cutting devices for trimmers. The first drawback is that it is impossible to work with a disk tool when the grass is performed next to obstacles in the form of trees, buildings, stones, shops, etc.P. When a disk collision with an obstacle, the drive is inhibition, which is reflected in the form of such minuses:

• The engine overheats
• The cutting parts of the disk that are blunted are damaged
• Transfer mechanisms. flexible and hard shafts (gearbox) come out of order

If you plan to mow thick grass in the field, then do without a trimmer for grass with an installed metal disk, it is impossible. The fishing line for a trimmer is used to prick small grass in personalities near obstacles.

It is interesting!On trimmers with a curved rod structure, you can not use steel discs due to safety. If the disk attaches an obstacle, then the effect of returns arises, through which the cutting part can fall under the feet of the operator. As a result, the operator risks getting serious injury.

Trimmers for grass

Easy Start system and primer for pumping fuel. Easy engine start

The battery includes. you can immediately start work!

Work confidently. the holder of the power cord will not allow him to disconnect from the outlet

The upper location of the engine to ensure the balance and convenience during work

Easyedge function to trim the lawn edge

Saving time and effort due to the Easystart electrical wiring system

Translucent fuel tank for light tracking fuel consumption

Universal use: you can work from the battery or power grid

Unique Easystart electrical wiring system, works with a knife and fishing line

Vibration damping system to reduce fatigue during prolonged work

The easiest model among 4-stroke trimmers in the manufacturer line

Combined protective casing for ease of work with a knife or head of a trimmer for grass

Easy transition to the ending mode of the edge

Reel-Easy Spool-a minimum of time for winding fishing line

Garden trimmer for grass. mobile hand.on.hand tool for haircuts. It is enough to put in the order of the entire territory of the summer cottage, but where there is a lawn mower, it is necessary to cut grass in hard.to.reach places, near trees, shrubs, hedges. Light and compact trimmers for grass cope not only with high grass, some models can cut even a small shrub.

engine’s type

Electric. Light in weight and operation, not noisy. Varieties:

• The engine below. convenient in operation, have small dimensions, power up to 650 watts.
• Engine at the top. a power of about 1 kW, can be with knives or replaced nozzles.

Gasoline. for large areas, t. to. independent from the cable. High power for any vegetation, up to shrubs. Engine:

• Inside, the coil will show how many recesses to wrap (two or one). If there is one recess, both ends of the threads will be laid along this recess. If there are two of them, the antennas are laid out separately. each in its depths.
• It is necessary to rewind from 2 to 4 meters of polyethylene thread and plunge it with two ends into the hole.
• Wrap both threads in the same direction as the drum.
• When all the hair is wound, the ends should be fixed in the grooves or hold on.
• Both ends are stretched from the outside of the clip body.
• After that, the drum is assembled and inserted into a mower.

Tips and steps to replace the cutting element in the video.

To insert a fishing line for a trimmer into a lawn mower with two grooves in the drum, you need to use the previous option for refueling this plastic thread. In this case, each end of the mowing fishing line of the hair will be wound along its groove. All other actions are similar to the previous process.

A coil or a roller can have a completely different design than the previous two options. A fishing line for a trimmer can be stitched through the eye, which passes inside the coil. In this case, you do not need to disassemble the roller drum and manually wrap the plastic thread.

The plastic thread is sewn through the hole and turned by pressing a special button. This button is located on the housing and is designed to operate the equipment, to be able to produce hair as it is worn.

Do not worry that the plastic thread is wound in the wrong direction, because in this design it can rotate in only one direction.

Security measures

For quick and safe replacement of the cutting element on the drum mower, it is necessary to observe precautions. Before removing the coil, it is necessary to turn off the equipment from the power source (if the lawn mower works from electricity) to wind a fishing line for a trimmer on a lawn mower

Here I want to mention the rating of the reliability of electric lawn mowers, which will help you choose a reliable assistant.

Another important compliance with safety rules. Press the lock button. You can find out how it is located on the equipment case, following the instructions. For example, instructions for a gas mower can be found here.

Remember that the cutting element should be adjusted. There is a button on the block case. If the process does not start automatically and the thread tension decreases, the button is clamped, and the fishing line for the trimmer with force is pulled out of the coil.

It should be remembered that replacing the cutting element in the lawn mower. This is an important process that requires responsibility. All this must be done in stages, and only a special plastic fishing line for a trimmer must be inserted into the coil. Iron cable, high.quality wire or even an enhanced fishing line for a trimmer are not suitable here.

Result

If there is a cottage or a large plot of land next to your house or cottage, then the lawn mower should be used for easy cleaning of grass and weeds. If you think about choosing an electric lawn mower or gasoline, click here and you will find comparative characteristics of various models.

Over time, a fishing line for a trimmer on a mower wear out and requires a replacement. This can be done independently. This polyethylene thread must be selected depending on the model of the mowing. It is also worth familiarizing yourself with the rest of the car, for example, you will find information about the blades of the Craftsman lawn mower, which also wear out and lead to irreversible consequences.

The device of the coil, into which the fishing line for a trimmer of hair growth is inserted, is very simple. But it depends on whether the coil with one or two threaded antennas is working

It is important to take precautions when replacing the coil

When the use of knives is relevant

When using motorcycles in summer cottages, the most popular nozzle is a fishing line for a trimmer. It has a small price, suitable for different trimmer heads, is safe when working. The minus of the use of the fishing line is that it is convenient only for the bevel of low shoots. In other situations, the string is immediately clogged, regardless of whether the gasoline or electric model of the trimmer for grass is used. In addition, vegetation is wound on a spindle, which creates significant resistance on the shaft and leads to its breakdown. It can also provoke a failure of the piston system in benzocos or burning out the motor in electrimmers.

Therefore, for mowing high or hard vegetation, various nozzles are used. So, for harvesting tall and rough grass, thin shoots of trees and shrubs to install and use it better. This nozzle clogs much less often, which contributes to the greater wear resistance of technology.

On a note! Due to the fact that the engine of electrical and battery models is less powerful than on benzocos, so the use of discs is more relevant for gasoline braids.

Features of disks for motorcycle

Disks-ceremonies are produced by plastic and metal, as well as various shapes to perform diverse tasks.

• Two-, three- and four-lobed knives with pronounced blades are used for mowing grass and overgrown trees. However, they are not suitable for harvesting hay, as the shoots are crushed, cutting them several times.
• Massive four.lobed discs are intended not only for clearing the earth from grass, but also for hay mowing. They prevent multiple cutting of shoots, thereby making them suitable for harvesting for the winter.
• Disks with cutting faces around the perimeter are relevant for the bevel of reed and reeds. Such knives are very heavy. this is the necessary quality to cut thick stems.
• Professional discs with a saw tooth for artisans and motorcycles allow you to cut down small trees and bushes.

Plastic knives are used as an alternative to metal disks. They do not need to be tightly attached in the head, and they revolve as a result of exposure to centrifugal force. The strength of the plastic knives is high, so the service life is quite long.

On a note! The advantage of plastic disks lies in the fact that, having hit an irresistible obstacle, they bounce, and there is no re.contact.

When to use the disk on the trimmer instead of fishing line

What is the difference between a metal disk from the fishing line per trimmer for the grass, it is already clear. Когда же необходимо завершить кошение леской, и закрепить на триммере металлический круг. This question is popular among beginners, since if you continue to mow large and thick grass with the cord, then it will wear out quickly. This is due to the fact that the fishing line for a trimmer with high speed begins to break about thick.stubble grass, which leads to its damage and, accordingly, rapid wear.

Apply knives on the trimmer should be with the following vegetation mowing:

• High and coarse grass cover
• Storms and dryness
• Young shoots of trees up to 7 cm in diameter
• Homemade thick.stem plants like raspberries, rose hips, currants

The use of knives eliminates the rapid wear of the fishing line, and also increases the efficiency and productivity of the use of a travic tool.

Instructions for replacing a disk on a gas tank with a step.by.step description

Having sorted out the design of the cutting knives, it remains to find out the process of replacing them and installation on the tool. If there is a head with a fishing line on a gas station, and it is planned to install a metal disk, then no remodeling of the structure will be needed.

To install a metal disk on a trimmer for grass, the following instructions must be followed:

• First, a plastic protective casing is removed. it is not necessary. Depending on the model of the tool, the dismantling process may differ. If the trimmer has a metal casing, then it is not necessary to remove it. Removing a plastic casing is performed in order to install a metal
• Using a special key-player or screwdriver, it is necessary to block the gearbox. The shaft blocking hole can be located on the side or on the end side
• A mowing head or spool is twisted from the tool if they are installed
• A disk is installed in the place of the head or spray. The internal diameter of the disk should be in a special groove. The nozzle is installed so that the front side (with letters) looks upward
• After installing the disk, a fixing washer of the corresponding size is placed. After that, the mounting nut is screwed, having previously blocked the gear shaft. Direction for screwing the fastener. counterclockwise
• After completion of work, it is necessary to install a protective metal casing. If it is not, you should leave a plastic casing

As you can see, the procedure for replacing the disk on the trimmer is not at all difficult, and takes no more than 5 minutes in time. Below the video shows how to properly change the mowing heads and circles on benzocoses.

Disk selection criteria

You need to choose a plastic or metal knife, given the area of ​​the site that is planned to be processed, as well as the type of trimmer for grass is electric or gasoline. The number of blades will depend on which shoots must be removed using the tool. Choose the desired disk shape, the number of blades and manufacturing material can be using the instructions for the operation of the device. It usually prescribes which mills are recommended to use to solve certain problems.

Material

It is not recommended to put metal knives on electrocos, since the design features make their use dangerous for the user. This is due to the curved shape of the bar, the absence of stops on the handles, as well as a high speed of rotation.

Important! Direct rod provides the safe use of a trimmer for grass at such moments when the disk, rotating, pushes into the obstacle. In this situation, he bounces back. towards a person, so a curved design can cause an injury.

On trimmers with a flexible bar in terms of safety, plastic knives should be used. Their purpose is a mowing of soft grasses, dry. Whereas metal disks do a great job with high, thick, hard shoots, shrubs, as well as shoots of trees.

Blades

The number of blades is important in solving diverse problems. So, two to three pieces are enough to grind the grass. For hay harvesting, it is necessary that there are four to eight blades on the disk. To destroy small shoots of trees and shrubs, instead of blades on the discs, there should be a large number of small teeth.

Sharpening of the disk

Regardless of the quality of the disk, over time it is stupid and begins to cut the grass poorly. If the knives are still relatively new, and the replacement is inappropriate, you can sharpen them with your own hands.

Important! For sharpening, only those discs are suitable on which there are no attacks from solid materials. Such details are thrown away, and instead new.

• disassemble a trimmer for grass, remove knives;
• Carefully inspect the disk. if cracks are discovered, it is better to change the part to a new one, since its further operation is unsafe;
• bent blades can be carefully bend with a hammer;
• Given the size of the disk, you need to choose the right file for metal, this will provide more convenient work;
• At an angle of 30 ° equally sharpen all the upper cutting edges of the disks;
• collect a trimmer for the grass in the reverse order.

To sharpen the disk, you can use an sandpaper at low speeds by installing a circle for grinding with medium.sized grain. Through such a tool, the process will move much faster. For safety, you need to put on gloves on your hands, and a protective mask or glasses on your face.

So, for beating grass on gasoline and electrimers, plastic and metal disks of various shapes are used and with a different set of blades. They are chosen in accordance with the type of work performed and the size of the processed territory. If the knives on the mower are swept away, they are easy to sharpen or change them on their own. Despite the simplicity of the procedure, you need to be neat and remember the safety so as not to injure by negligence or not to damage the technique. A more detailed description of the replacement of knives in relation to a specific model of a trimmer for the grass can be viewed in the instructions for operation or on the official website of the manufacturer. For clarity, the general process of the process is shown in the video.