Which oil is suitable for a trimmer. Fuel for a twostroke engine: Theoretical part

Which oil is used for a trimmer

Many do not comply with some important recommendations for pouring fuel in a trimmer or gas tank, which ultimately leads to unpleasant consequences. Consider important recommendations on how to properly fill in the gas tank of motorcycles diluted fuel from gasoline and oil:

Prepare a funnel or watering can. Despite the large diameter of the hole of the gas tank, very often when trying to get into it, a certain part of the fuel is spilled, which enters the tool case

The fuel that came to the instrument can cause ignition when heated, so it is very important to use a funnel or a watering can Before twisting the cork, you should thoroughly clean the surface of the tank, since pollution can get inside, which will cause a quick clogging of the benzophilter Work on pouring fuel must be carried out in calm weather or in a secluded place in order to exclude the likelihood of dust and small grains of sand inside the tank Do not leave the open hatch of the tank for a long time, since not only small grains of sand and dust can fall into it, but also insects During flooding, do not inhale the vapors of gasoline, as they are dangerous for humans. When working with a trimmer, the master should use protective glasses, headphones and respirator Pour fuel into the tank must be before the mark

If you pour a full tank, then with screwing the cork, some will result in a non.Excessive use of fuel. In this case, it is better to shorten than to pour

Given these recommendations, you can significantly extend the service life of the gasoline tool in question.

It is interesting! Work on the preparation of the mixture and pouring fuel is also recommended in protective gloves.

Lubricant system of two.Stroke and four.Stroke engines

Four stroke engines Equipped with separate lubrication systems and preparation of the fuel mixture.

Therefore, the pump supplies oil directly to the rubbing surfaces, that is, the crankshaft bearing and the place of contact of the piston with the walls of the cylinder.

To do this, the lubricant is poured into a special container, from where it comes to the channels to the areas of increased friction.

Will a 4-cycle lawnmower run on 2-cycle gas/oil mix?

In addition, through the crankshaft and rod oil gets to the piston and washes it, reducing the temperature and lubricating the walls of the cylinder.

Two.Stroke engines are deprived of a separate lubricant system, but they also have a crankshaft bearing in need of reducing friction force.

In such power units, the fuel mixture first enters the crankcase, where the crankshaft bearing is located, and then under the influence of discharge passes by the piston, cooling it and lubricating the cylinder walls, enters the combustion chamber.

The efficiency of lubrication by the fuel mixture is much lower, than with engine oil, so the life of the bearing of the two.Stroke engine, which means the crankshaft and the connecting rod, is noticeably less than the same part of the four.Stroke engine.

In addition, a two.Stroke lubrication system makes special requirements for the oil, because it should burn as much as possible in the cylinder and form a minimum of toxic substances.

What is the difference between oils for different types of engines?

The different principle of operation of the oil system forces the use of lubricants with different properties and characteristics.

In addition, in four.Stroke engines the oil serves all season, and in two.Stroke engines it lubricates the details, then burns in the cylinder, which also affects the requirements for it.

Four stroke

According to the principle of operation, the four.Stroke power unit is completely identical to automobile internal combustion engines.

So lubricant requirements are the same, as to ordinary motor oil for high.Speed car engines.

The main parameter of the lubricant for four.Strokes is viscosity, which describes how fluid the oil will be at the operating temperature, and indicate the parameter with the letter “W” and the numbers before and after it.

The numbers before the letter describe the minimum negative temperature, in which it retains its lubricant, but for trimmers this parameter is not relevant, because it is not used during frost.

The numbers after the letter describe the viscosity at operating temperature. Typically, for four.Stroke trimmers, they take a lubricant 5W30 or 5W40.

Another relatively important oil parameter for four.Stroke engines. Type of lubricant, that is:

Mineral oil is made by thermal distillation (distillation) of oil and heavy oil products. It is cheap, but has mediocre lubricants and low resistance to high temperatures.

Synthetic oil is obtained from various gases emerging from the Earth along with oil. It is much more expensive, but has noticeably better lubricant and resistance to high temperatures. Semi.Synthetics is a mixture of both basics.

Over, the requirements for the clock depend on the characteristics of the motor and the conditions of its work, However, trimmers engines work in noticeably more comfortable conditions than automobile, therefore, oil intended for any engine is suitable for them. For this reason, the API class is not indicated on the container with lubricant fluid for trimmers, that is, compliance with certain automobile engines.

Two.Stroke

Since oil for such engines works only a few moments, after which it burns in the cylinder, then It does not require the same resistance from it, which is characteristic of the lubricant of four.Stroke engines.

In addition, it should have a higher lubricant, because such oil comes to the bearing being very diluted with gasoline.

Since all two-stroke engines of garden equipment work approximately in the same conditions, the oil for them has no divisions in viscosity or some classes.

Two.Stroke oil is suitable for a trimmer, even if it is written on the packaging or container that It is intended for the following two.Stroke devices:

An important condition is complete combustion in the cylinder, otherwise the trimmer will greatly pollute the environment, and the smell of its exhaust will be extremely unpleasant.

That is why the incorrectly composed fuel mixture gives a thick dark or blue exhaust with a sharp unpleasant odor. The same effect appears when the apparatus with a faulty or non.Configured engine/carburetor appears, as well as with strong encouraging.

Obtaining a mixture

How much oil is pouring per liter to get high.Quality gasoline mixture? It would seem that there is nothing complicated in mixing two substances. The preparation of the mixture is often complicated by the fact that in various sources, various information is indicated. For example, the instructions indicate the proportion of 1 to 40, on the fuel tank of the trimmer 1 to 25, and on the canister with oil 1 to 50.

There are a number of requirements for how to dilute. Do not add too much oil. This leads to a decrease in ignition characteristics. As a result, the devaluation of the efficiency of the power unit occurs, and the general decrease in its resource. In case of oversaturation of gasoline mixture with oil, soot sediments (ventilation Windows of the cylinder) will form on the inner surface of the walls of the engine. This is fraught with the formation of a nap on the piston.

Neither oil starvation, nor excess lubricant on a gasoline basis are a good basis for prolonged ICE operation. For a trouble.Free prolonged operation, the same number of components is necessary. Breeding is best done using the same measured tools to exclude unnecessary errors.

How to calculate, let’s say how much oil is pouring per 1 liter of gasoline with a required ratio of 1 to 50? To do this, we transfer the volume of gasoline into milliliters 1l = 1000 ml. Accordingly, to achieve a ratio of 1 to 50 thousand, they are divided into fifty. Only 20 g of oil will need one liter of gasoline. Someone measures the oil with a 20 cubic syringe, but for such purposes there is A special measured spoon, which is sometimes supplied with oil from some manufacturers.

For ease of calculating the ratio of oil and gasoline, we bring the table https: // cmetnik.Ru/oil/

How to choose the right oil

When choosing a lubricant for motorcycles in the first place, it is recommended to follow the recommendations specified in the operating instructions.

So, for example, for the use of STIHL gasoline trimmers, the manufacturer advises using the branded oil of the same name, which fully takes into account all the features and operational modes of the power unit.

As in the case of any demanded goods, the possibility of purchasing a fake or expired product is not excluded. Therefore, you should carefully examine the packaging. The label should be typographic quality, and the shelf life is unexpected.

Oil replacement in a 4-stroke engine

In a lawn mower with a four.Stroke ICE, pour gasoline in a tank, and oil in a special hole that is in the crankcase. Operational instruction for equipment from the manufacturer contains information about the frequency of lubrication replacement.

It should be taken into account that the effectiveness of the lubricant after about 50 hours of operation of the unit decreases. If you need to pump out small areas, then in one season so many working hours are unlikely to get. In this case, the lubricant should be changed when preserving the device at the autumn-winter period.

Correct Way To Mix Gas and Oil For a ChainSaw, WeedEater String trimmer. Easy 2 Cycle Oil Gas Mix!

Replacement of engine oil is performed as follows:

• At about 15 minutes, the lawn mowing motor is launched at idle speeds so that the system warms up, and due to this, the fluidity of the lubricant increases (the viscosity decreases);
• Unscrew the plug of the drain hole located on the crankcase;
• They include the lawn mower towards this drain, having previously set the container to collect the developed lubricant (as in the photo below);
• After the development is dragging, the cork is twisted into place;
• The mower is installed on an even platform;
• Open the upper hole;
• The new oil appropriate for a 4-bed engine is poured, periodically checking its level with the probe;
• Когда смазка достигнет требуемой отметки, отверстие под заливку закрывают, плотно закручивая пробку.

For filling in four-stroke ICE, you can use various oil stamps, for example, 10W40, SAE-30 suitable in their operational properties. For most models, it is suitable lubricant of the class SF and above. It is recommended to fill in the winter frost.Resistant lubricant.

Semi-synthetic oil Yuko Semisynthetic 10W-40

It is not recommended to drain practices directly to the soil, so as not to pollute it. To select a spent lubricant, you can also use various devices. One of the possible options is presented in the photo further.

The process of replacing the lubricant in the engine system of the wheelbreaks is quite simple. Carrying out all the operation usually takes up to 30 minutes of time.

The best option for both two.Stroke and four.Stroke engines is the use of gasoline and oil, recommended by manufacturers. Instructions for suitable brands are given in the instructions for the lawnical mower. The lubricant must have a viscosity not lower than the indicated, otherwise it simply cannot perform its functions normally. The gasoline used should not be a brand higher than recommended by the manufacturer, because the pistons, valve or rings can burn out. Filling fuel or lubrication, it is also necessary to observe their volumes given in the instructions. Especially the proportions should be observed with independent preparation of an oil-banzin mixture.

Procedure

Various methods are used to lubricate the gearbox and shaft, because these Details differ in design and principle of operation.

In addition, the technology of lubrication of the shaft for devices with a collapsible bar and the ability to pull out the bushings is distinguished.

It is also worth noting that when introducing a lubricant to the gearbox, the procedure depends on the tool used, that is, a universal tube or plastic syringe.

Gearbox

Before the manipulation, unscrew the bolt that closes the opening open for this. Further actions depend on what you plan to lubricate the gearbox.

If you use material in plastic universal tubes with a conical nose, then:

• Cut the nose so that the diameter of the hole is 2-3 mm;
• Insert the nose of the tube into this hole;
• Squeeze the lubricant until her surplus gets out of the hole;
• Pull out the nose of the tube;
• Screw the closing bolt;
• Clean the surface of the gearbox with a clean rag.

If you use a home.Made mixture or ready.Made lubricant for the electrimmer reducer in another container, then Use a 10 cm 3 syringe with a syringe. Pull the piston from the syringe and fill it with oil, then use it in the same way as a universal tube.

Do not use a container from under the fuel and lubricants without washing and degreasing, because it is not known what could be in the contents earlier and how something will affect the work of the gearbox.

• Remove the cutting tool;
• Remove protection;
• Remove the gearbox;
• If your trimmer has a collapsible bar, then separate it;
• Unscrew the bolts connecting the halves of the housing of the electric cos and fixing the bar;
• Pull the bar out of the body;
• Remove from the bar or both of its halves of the shaft or shafts.

In more detail, the process of disassembling the bar and the shaft extraction is described here (with your own hands).

To lubricate the shaft, first clean it of the old oil, wipe it with diesel fuel or gasoline and degrease. So you remove the products of the bushings from its surface, which means extend the life of the trimmer.

• Put a little butter or mixture on a clean, unlawful rag;
• Distribute it by the shaft so that the layer thickness is approximately 0.5 mm;
• Insert the shaft smoothly into the bar until it stops and scroll several times;
• Pull the shaft;
• Spread with a mixture or a finished product again;
• Insert from the other side to the stop, then turn several times;
• Pull the shaft;
• Once again, apply a lubricant;
• Insert, as expected;
• Collect an electric cost.

If the design of your electrimmer allows you to pull out and insert the bushings back, then:

• Pull them out;
• Clean as described above;
• Cover the inner surface with a mixture or a finished product;
• Insert each sleeve in its place;
• Apply a lubricant to the shaft and insert it from the right side;
• Collect a trimmer.

Reviews of 5 best trimmers for battery strings (updated 2020 g.)

Is a trimmer suitable for me with the battery?

Not every yard is suitable for a trimmer with battery power, it has some shortcomings that are associated with their high maneuverability. They are recommended for those who have a small courtyard that can be quickly bypassed.

If you need to process a larger yard for you, it would be nice to purchase an additional battery or two, so that you are able to do everything in one pass.As long as you have juice, they will rapidly manage weeds and herbs, and you will not have to fuss for you.

Trimmers with battery power not enough power to cut a heavy brush is a sad reality, but if you planned use it is to clear the hedge or other dense plants, then another thing awaits ahead.

In the process of our tests, we were really surprised how far this development advanced, but if you are engaged in harsh squares, we are advantageously advised to find a model with an internal combustion engine, since the difference in power is incredible.

But for the yard of small and medium size, inhabited only by grass and weeds, they may be the best method to cut the edge and cut without the need to deal with massive extension cords or to find out the correct mixture of oil and gas for working with 2 cycles of the motor from.

If you choose any of them, they will also become an economical choice. They also require the least service than gas trimmers, and you don’t have to worry about running to the nearest gas station if you have electricity.

Ear drops Lamigex

The small clinical test of 2014 associated the effects of standard drops of ciprofloxacin for healing the ears and a mixture containing subsequent essential oils:

• Clove oil, Syzygium aromaticum
• Lavender oil, lavandula angustifolia
• Butter Herb-Robert, Granium Robertianum

Participants received 3 drops every 12 hours during the course of the week.Researchers found that this mixture, named Lamigex, was as effective as the ear drops of ciprofloxacin. Both healing improved the symptoms of soreness, itching and discharge.

Oorgano oil

Mexican butter Oregano, or Lippia Graveolens. Can also help with ear infections.

The 2011 study included oregano oil tests in vitro, which showed that it has antivirus qualities.

These effects in the main thing are justified by the oil component under the title of Carvacroll.

But this study does not justify that butter Excellent against the auricle. Researchers claim that subsequent studies are needed to find how excellent it is butter.

Although this is often overlooked, the ability to control the speed of the trimmer using the trigger has a number of applications.A simple switch of turning on / off will simply make your trimmer constantly work at maximum speed that the engine can withstand, which will also quickly discharge a limited battery.

Using a trigger with adjustable speed, you can extend the battery life, slightly using it in open areas with grass and pulling it a little more if you come across thicker areas of weeds. If you plan a large yard with a large number of open space, this is an indispensable function.

What to look for when choosing oil?

Modern two-stroke engines of Motokos are seasoned with a mixture of AI-92 gasoline and oil marking “2T”. The use of fuel with a higher octane number will contribute to an increase in the temperature of the flash and, as a result, burning out lubricants.

Undoubtedly, the best oil for a trimmer is the manufacturer recommended by the manufacturer, but the owner does not always have the opportunity to purchase a “branded” lubricant. Experts recommend Shell Helix Ultra, based on PurePlus technology, which helps to improve the basic properties of lubricants.

For gasoline trimmers of the German manufacturer, STIHL is necessary use Oils STIHL HP Ultra, STIHL HP, STIHL HP S. The budget substitute can be the products of the Vityaz company, which in its properties is the most similar to the recommended material.

Motokos oil. How to choose in what proportions to breed

Many of you have a benzo tool in the household, for example, in a private house you can not do without a chainsaw. You understand, the harvesting of firewood for the winter is useful at a construction site and repair and in general, this is a very necessary tool. If the country house also has a decent area in size, then to combat grass just needs a trimmer or motorcycle, which also work on gasoline.

Of course, they can be bought and electric, but not everyone likes to pull a 30-meter extension cord to dig an area overgrown with grass knee-deep. Therefore, most people prefer to work as a gasoline tool. As you know, you need to add special oil for two.Stroke engines to gasoline. We’ll talk about it, because this is a very important aspect, if you do not add oil and add in the wrong proportions, then your engine will quickly “grunt” and your path will lie to the service center. To avoid all these troubles, add only high.Quality oil and in the correct proportions.

The most popular for chainsaws, motorcycle and trimmers is the products of the famous company STIHL. It is sold in 2 packages. 1 liter and 100ml. For those who work hard, a liter bottle is suitable, and a small bottle is enough to “drink” at a time. A capacity of 1 liter costs 250 rubles, and for 10 ml. 60 rubles. If you take a large one, then the savings are obvious.

Oil is added to gasoline in a proportion of 1 to 50, that is, for example, add 100 ml per 5 liters of gasoline. As you can see, a small bottle is great for 5 liters of a mixture of gasoline for refueling a chainsaw or trimmer. On a large bottle on the side there are special marks by which you can determine how much oil was poured out of the bottle. If you bought a large 1 liter bottle, then buy a 20ml syringe in a pharmacy. Very convenient. 1 oil syringe per 1 liter of gasoline.

Experts advise using branded oil for their technology, it is perfect, since it is developed and tested precisely on the instruments of calm. I note that Stiel has its own brands, such as VIKING (popular models of gasoline trimmers). For them, also use Stilevsky oil and there will be no problems at all.

If you have made a gasoline mixture more than you can use it, then it is best to store the remains in a metal canister or in a glass container. In no case do not store the mixture in a plastic bottle. Of course, if you consume the remains after a couple of days, then you can pour the remnants of the mixture in a plastic one and a half, however, if the mixture is stored for a long time, then either a canister or a glassotter. The thing is that the gas mixture corrodes the plastic bottle, microscopic plastic precipitation appears in the mixture and this is very bad for the engine. Keep this in mind if you want your tool to work for a long time and without problems.

Which oil is used for a trimmer and garden equipment

Today we will answer the frequently asked question: which oil to choose for a trimmer with a two.Stroke engine? How, what and in what proportions.

Oil is one of the most important components for good engine operation. This is especially true for two.Stroke engines. So, as the oil is mixed with gasoline in them and on the correctness of the selection of oil depends on whether you will mow the grass or go to the repair workshop.

So, which oil is recommended to use in two.Stroke engines and why?

The best budget oils for trimmers and lawn mowers

Hammerflex 501-008 SAE 10W-40

The product is compatible with 4T devices. One of the best budgetary decisions for trimmers, motoblocks, lawn mowers, mini-tractors and other similar equipment. Lubrication on the surface creates a thin dense protective film supporting motor in impeccable cleanliness, which significantly extends the service life.

Huter 2T 1 L

The product is compatible with almost any means of equipped with a 2T engine. High.Quality additives, effectively interact even with low.Quality gasoline and reduce the number of deposits on the crankcase. It is allowed to use in engines with a mixed and separate lubricant system. Positively affects the operation of the spark plugs.

• Prevention of jamming of piston rings;
• Minimal smoke formation;
• High fluidity;
• Optimal viscosity indicators.

Patriot Supreme HD SAE 30

Mineral oil for 4T engines with air and liquid cooling. The high content of additives protects the structure from corrosion and premature wear. The liquid withstands operation in extremely difficult conditions. It is recommended to use in the summer of the year.

Types of motor oils and their purpose

Choosing oil for benzotrimer

The oil for the gasoline trimmer engine is a lubricant that serves to reduce wear between the rubbing units.

The composition of the oil includes residual hydrocarbons and various additives that improve the properties of the final product. To ensure durable and trouble-free operation, gas troops recommend the use of oils, which in their physicochemical properties correspond to this type of motor.

Today it is customary to distinguish between three main types of oils by the method of obtaining them:

• Minerals created in the process of distillation of hydrocarbons;
• Synthetic oils obtained by processing natural gas or synthesis;
• Semi.Synthetic, including improved mineral oil with the addition of some synthetic components.

In order to prevent mixing of various types, the manufacturer adds dye to the oil, which shows the difference in the compositions of the lubricant.

Gasoline and oil for benzocosa

Benzokos is a fairly common technique for combating weed vegetation in summer cottages, in personal, road and housing and communal services. These devices have two more names. Trimmer and motorcycle. These units differ in their engines. Expensive of them have four.Stroke engines, all the rest are two.Stroke. Of course, the latter are most popular among the population, since it is easier in design and by mass easier and much cheaper than their four.Stroke competitors. However, two.Stroke models are inconvenient because the fuel mixture must be prepared manually for them, withstanding a strict dosage between gasoline and oil. In four.Stroke analogues, the mixing of these components occurs automatically, only the gas tank and oil tank should be filled with the corresponding substances. Let’s look at the question of the correctness of refueling precisely two.Stroke motorcycles, since it depends on how effective and long the work of such an unit will be.

For efficient operation of the trimmer, it is necessary to select oil for two.Stroke engines. This is due to the lack of an oil crankcase in such a device. The following classification is released depending on the chemical composition of the oil:

• Mineral ones. It is based on an oil distillate, suitable for low.Power technology and with an air type of cooling, but requires frequent replacement and can only be used in good weather in the warm season;
• Semi.Synthetic. Suitable for garden equipment with air and liquid cooling type;
• Synthetic. At the basis have complex ethers, do not require frequent replacement and can be used at any time of the year.

Oil for 2 stroke engines is characterized by good solubility and a feature of complete combustion. For a trimmer, it is recommended to use a lubricant that is suitable for devices with an air cooling system. Most often, the packaging indicates that the oil is intended for garden equipment and has a marking of the TA, TV or TS. Over, the last of them is most preferable.

If the consumption of motor oil during the summer season is planned large due to the presence of a chainsaw, a bush cutter, a lawn mower in the garden arsenal, then it is advisable to buy 5 liters of oil at a more favorable price. If it is needed only to mix with gasoline and season the only tool, then 1 liter will be enough.

Often manufacturers of benzos release suitable oil, so you can facilitate your choice if you select the liquid of the corresponding brand.

Oil selection rules

Motor oil depending on the chemical composition:

• Mineral. Made of oil distillates and is intended for low.Power air.Cooled equipment;
• Semi.Synthetic. Is a mixture of mineral and synthetic oils and is suitable for 2T and 4T, as well as for air and liquid cooling;
• Synthetic. Produced on the basis of complex ethers and can be used in powerful equipment, as well as for work in difficult climatic conditions.

Depending on the classification of the API, the following groups of oils for trimmer engines can be distinguished:

• That. For low.Power equipment with an engine volume up to 50 cm³ and air cooling;
• TV-for powerful equipment with a motor volume of 50-200 cm³ and an air cooling system;
• TS. For a powerful two.Stroke equipment (motorcycles, chainsaws, lawn mowers, etc.) with a engine volume 50-200 cm³;
• TD. For motors of boats with liquid cooling.

To choose the optimal oil for a specific trimmer model, it is better to take into account the recommendations specified in the instructions. For motos 2t, API-TV class oil and API-TS is usually used. Leading manufacturers of garden equipment themselves develop and produce oils for their equipment

Such lubricants most fully satisfy all the technical and operational characteristics of specific series of trimmers. For example, for STIHL motorcycles FS 5, it is best to use the STIHL HP or STIHL HP Super oil, for Husqvarna 143R, Husqvarna HP or Husqvarna LS oil is suitable. But for the brand Patriot, ordinary M-8V mineral oil is suitable

Leading manufacturers of garden equipment themselves develop and produce oils for their equipment. Such lubricants most fully satisfy all the technical and operational characteristics of specific series of trimmers. For example, for STIHL motorcycles FS 5, it is best to use the STIHL HP or STIHL HP Super oil, for Husqvarna 143R, Husqvarna HP or Husqvarna LS oil is suitable. But for the brand Patriot, ordinary M-8V mineral oil is suitable.

Motokos oil. How to choose in what proportions to breed

Many of you have a benzo tool in the household, for example, in a private house you can not do without a chainsaw. You understand, the harvesting of firewood for the winter is useful at a construction site and repair and in general, this is a very necessary tool. If the country house also has a decent area in size, then to combat grass just needs a trimmer or motorcycle, which also work on gasoline.

Of course, they can be bought and electric, but not everyone likes to pull a 30-meter extension cord to dig an area overgrown with grass knee-deep. Therefore, most people prefer to work as a gasoline tool. As you know, you need to add special oil for two.Stroke engines to gasoline. We’ll talk about it, because this is a very important aspect, if you do not add oil and add in the wrong proportions, then your engine will quickly “grunt” and your path will lie to the service center. To avoid all these troubles, add only high.Quality oil and in the correct proportions.

The most popular for chainsaws, motorcycle and trimmers is the products of the famous company STIHL. It is sold in 2 packages. 1 liter and 100ml. For those who work hard, a liter bottle is suitable, and a small bottle is enough to “drink” at a time. A capacity of 1 liter costs 250 rubles, and for 10 ml. 60 rubles. If you take a large one, then the savings are obvious.

Oil is added to gasoline in a proportion of 1 to 50, that is, for example, add 100 ml per 5 liters of gasoline. As you can see, a small bottle is great for 5 liters of a mixture of gasoline for refueling a chainsaw or trimmer. On a large bottle on the side there are special marks by which you can determine how much oil was poured out of the bottle. If you bought a large 1 liter bottle, then buy a 20ml syringe in a pharmacy. Very convenient. 1 oil syringe per 1 liter of gasoline.

Experts advise using branded oil for their technology, it is perfect, since it is developed and tested precisely on the instruments of calm. I note that Stiel has its own brands, such as VIKING (popular models of gasoline trimmers). For them, also use Stilevsky oil and there will be no problems at all.

If you have made a gasoline mixture more than you can use it, then it is best to store the remains in a metal canister or in a glass container. In no case do not store the mixture in a plastic bottle. Of course, if you consume the remains after a couple of days, then you can pour the remnants of the mixture in a plastic one and a half, however, if the mixture is stored for a long time, then either a canister or a glassotter. The thing is that the gas mixture corrodes the plastic bottle, microscopic plastic precipitation appears in the mixture and this is very bad for the engine. Keep this in mind if you want your tool to work for a long time and without problems.

The second most popular brand of oil is a non.Bonding hokesworm. Of course, if you estimate it, after all, STIHL chainsaws use more people, at least all my friends and their friends use only them in their work.

However, there are those who do not have souls in the Husqvarna tool and I understand them, since I personally do not see much difference between Khuskvarnaya and Shtil, and one and the other tool is very high quality. But I saw satisfied owners of Husqvarna chainsaws. They say, saws are just super. I myself did not saw, however, I always listen to the opinion of people. So, if you have a gas.Based gas tool, then it will be better for him to use special branded oil. Although nothing terrible will happen if you dilute the gasoline with a signs. But since the manufacturer recommends using only its products, we will do so.

On sale you can find liter containers. Black stylish bottle, the same marks on the side, and with a person (to know how much oil was cast from a bottle). As for me, absolutely identical quality. There is such a bottle of 270 rubles, a bit more expensive.

Both that and other oil are high.Quality, the cost is approximately the same, each is diluted in a proportion of 1 to 50. So feel free to buy anyone, of course, it is better to take the oil of the brand you have a tool. Then everything will be perfect, as the manufacturer advises. Good sawing, spinning grass and let your benzo.Tool work for a long time without breakdowns.

Suitable lubricants

The best grease option is specialized lubricants that are sold in technology stores and are designed specifically for cars.

Special oil

This oil is designed to process precisely haircut machines. A small bottle usually comes in the kit, grabs it for a long time. Lubrication is an oil product, it is clean, without smell and low.Fat. Such a substance is suitable not only for processing the machine after work, but also for periodic cleaning. Machines oil is produced under the following brands:

If you can’t find a special lubricant on sale, it can be replaced with silicone grease, synthetic and mineral oils with a low viscosity coefficient or petroleum jelly.

Mineral and synthetic lubricants with low viscosity

Services are often used by mineral and synthetic oils with small density. They are convenient to use: are easily distributed along the processed surface, flow into hard.To.Reach places, sold everywhere and there are pennies. Synthetics are made of oil, which is cleaned and improved by “additives” in laboratory conditions. The most popular and affordable lubrication of this class is Xado Atomic Oil. Mineral compositions, in fact, are purified oil. One of the best Yuko Classic.

Silicone Grease

Such compounds based on polydimethylsiloxan are produced. This is the best alternative to specialized lubrication. They are hypoallergenic, easy to use, do not dry over time. Search on the shelves lubricants can be called by name: PMS-200 and PMS-100. The number means viscosity. The larger it is, the thicker the composition.

Vaseline lubricant

Suitable is the one that can be found in pharmacies. It can be brought to the correct consistency Using gasoline for lighters. Before using such a composition, the machine must be carefully cleaned. Driving a lubricant to the right places conveniently with a syringe without a needle.

How much you need to fill?

Cultivators, minitors and motoblocks supplied to the Russian market are mainly equipped with Subaru, Briggs Stratton, Honda or their Chinese analogues. They can be of different capacities and accommodate different amounts of lubrication. How to find out how many lubricants to pour from the canister so that the 4-stroke engine operates in optimal mode, and its details are not erased from the lack of lubrication?

The standards of lubricant consumption can be found from the instructions for the operation or technical documentation attached to motorcycle equipment. Below the table indicates individual lubricant consumption standards for the most popular engines models.

You can simply fill in motor lubricants by determining its number by the probe on the plug. The minimum level is practically limited to the length of the probe itself, and the maximum reaches the thread of the drain. You can also navigate by looking at the opening of the crankcase.

As a rule, in a walk-behind tractor or motor-boom with a 6-8-horsepower engine, about 0.6 liters of liquid are placed, in more powerful units-a little more than 1 liter. It is not without reason that the most popular packaging among manufacturers is a volume of 0.6 liters. It is such a norm of oil that is enough to refue to the full level of medium.Power motor vehicles, which is the greatest demand for owners of garden and summer cottages.