At What Angle To Cut The Ceiling Plinth

Selection of material and calculation of the number of skirting boards

Ceiling plinths are very popular, for the manufacture of which polystyrene, polyurethane and expanded polystyrene were used. The main advantages of such products are lightness, resistance to moisture and temperature extremes. Thanks to the various widths and a large selection of patterns and reliefs, it becomes possible to choose a plinth to create any decorative effect. Additional coloring of the ceiling plinths makes it possible to create a variety of artistic decor.

The problem of how to stick polystyrene and expanded polystyrene skirting boards on the ceiling should be solved with extreme caution, since they are easily deformed and damaged by mechanical stress. As for polyurethane fillets, such design elements are characterized by increased strength and the ability to maintain a clear relief shape.

Polyvinyl chloride ceiling plinth is widely used in cases where the budget for renovation and decoration of the premises is limited. However, when using it, remember that it is not recommended to paint such products. In addition, the PVC skirting board is afraid of temperature extremes, under their influence, the product may deform.

Before you go shopping for skirting boards, you need to make a few calculations. In particular, it is required to determine how much material is required to decorate the ceiling in a room of a certain area. First, measure the perimeter of the room, this value will correspond to the total length of the ceiling plinth. To calculate the number of fillets, it is necessary to divide the perimeter of the room by the standard length of the products, which corresponds to 1.2 meters, 1.4 meters and 2 meters. Experienced craftsmen performing finishing work recommend purchasing skirting boards of greater length, in this case, fewer connections are obtained.

The width of the plinth is determined according to the height of the ceilings in the room. In rooms with low ceilings, it is better to use narrow products; for high rooms, it is recommended to install a wide ceiling plinth. This visually reduces the height of the room.

Main steps

Installation of a ceiling plinth cannot be called a complicated and time-consuming process; even a novice master can do it. However, for a quality work, you need to know all the details of installing ceiling plinths. When solving this issue, you should be especially careful about the design of the corners. Errors and shortcomings at this stage become a prerequisite for the formation of cracks and mismatches, which to a greater extent spoil the appearance of the entire ceiling. Therefore, the problem of how to glue the ceiling plinth in the corners can be called actual.

Preparatory process

Before gluing the skirting boards to the ceiling in the corners, you need to prepare the tools that you will need when gluing the ceiling skirting board:

• To calculate the required amount of materials, you need a tape measure.
• It is recommended to fix ceiling skirting boards with quick-drying glue or putty.
• You can knead the adhesive composition in a pre-prepared container, it is best to apply the putty with a spatula.
• Remove excess glue or putty with a dry, clean cloth.
• For cutting skirting boards at a certain angle, it is best to use a miter box.
• Direct cutting of products is performed with a sharp construction knife or file.

It is recommended to glue the ceiling plinth on a pre-filled and leveled wall. As for the wallpaper, they are glued after the fillets are installed. In this case, the fastening of the elements will be more durable. In addition, when gluing new wallpaper, there is no need to change the ceiling plinth, since wallpaper strips are glued along the lower edge of the fillet. Fixing wallpaper floor Reduces the fixing strength of the skirting board and requires its dismantling when changing the finishing material for the walls.

It is recommended to solve the problem of how to properly glue the ceiling plinth in the corners with the help of acrylic or silicone glue, characterized by fast drying, or on a construction putty. With the help of a putty, the skirting board is glued directly to the wall, the frieze is glued to the wallpaper with the help of quick-drying glue. When using THESE materials for fixing products, there is no need to hold the elements for a long time to set the adhesive backing. In addition, with putty, you can simultaneously repair wall defects in the form of irregularities and cracks.

Cutting skirting boards at an angle

The process of deciding how to glue a wide skirting board always starts in one of the corners. In the process of manufacturing products, many manufacturers cut the skirting boards at a certain slope for easier decoration of external and internal corners. The problem of fitting fillets with a complex pattern or pattern is especially urgent. When using Bezuglov ceiling plinth, you can correctly and beautifully arrange the corner using a miter box or a saw.

Determining the slope and cutting the skirting board is done as follows:

• The product is applied to the ceiling in order to understand the direction of the cut for proper installation.
• You need to cut baguettes in a mirror image.
• To decorate the inner corner, the top edge is made shorter than the bottom edge.
• Correct outer corner occurs when the top edge is longer than the bottom.
• On the ceiling plinths, which will be located on the right side, make a cut on the left side.
• In the product located on the left side, the cut should be on the right side.
• When cutting the plinth, you must carefully advance the knife in one direction. In this case, the formation of chips and roughness can be avoided.

Here is the correct solution to the question of how to glue and cut ceiling plinths, the appearance of the ceiling depends.

For self-production with a miter box, you must perform the following steps:

• Take any solid foundation and draw a line on it.
• Then about 10 cm retreat and draw a line parallel to it.
• Draw a line through the parallels at right angles to them.
• This line is measured 5 cm on each mowing line and opposite points are connected.
• The resulting mowing lines form an angle of 45 degrees from parallel.

To cut the skirting board using a homemade miter box, the product is laid along the parallels and cut along the marks, taking the direction of the corner.

How to glue skirting boards to the ceiling in the corners. Step by step guide

When performing repair and finishing work, each stage should be treated responsibly. The final stage, when additional and decorative elements are mounted, requires special care. Most often they are in plain sight, so any mistake can spoil the appearance of the entire interior. Therefore, it is necessary to strive for the perfect execution of the final stages of repair and decoration.

Completion of any work on finishing the ceiling is the installation of ceiling skirting boards, which are called frieze or fillet. Thanks to this element, the transition between the ceiling and the wall becomes smooth, and the repair takes on a complete look.

Gluing ceiling plinth

For high-quality gluing of the baguette, you must do the following:

• Take a baguette and put glue on its back.
• The place of fixation of the product can be moistened with a primer or plain water to increase the adhesion of surfaces.
• The plinth is firmly pressed against the wall and ceiling and held for a while.

• Excess glue or putty is removed immediately.
• The resulting cracks and gaps are covered with putty.

If necessary, the skirting boards are painted in the desired color.

Cutting without tools

How to cut a corner of a skirting board without a miter box? It is possible to perform the calculation and cut manually. It is enough to make a good marking on the ceiling, then cut off the desired corner exactly. A significant disadvantage of this option is the inconvenience when you have to hold all the bars with your hands during the measurement process. In general, this method does not help to make the necessary measurements any worse.

Attached the product to the place where it will be mounted, you can immediately take into account all the errors on the walls. First, two pieces are cut at a 90 degree angle. Then one of the planks is applied, rests it against the wall perpendicularly. Draw the line along the ceiling, outline the desired contour. Then they remove the bar and apply a second one. for reciprocal marking. The intersection of the lines will be the bleed. Then the place for the future cut is marked on the slats.

Cut off the outer corners with a miter box

• Attach the skirting board to the corner and mark with a pencil where the outer corner begins on the skirting board.
• Then the plinth is placed in the miter box. The side that will be attached to the ceiling is laid on the bottom with a miter box, and the other side Press against the wall.
  The mark on the skirting board should be located near the left slots. Cutting off one end.
• Then, in the same way, cutting off the other half of the corner. Only the mark on the skirting board should be located near the right slots.

We apply both halves to the corner and check if there is a gap. If everything is in order, then you can glue the skirting board in place.

Strong ceiling plinth: secrets of correct angles without using a miter box. Installation of finishing: features

Many owners of houses and apartments are often puzzled by the question of how to properly cut the ceiling plinth in the corners in the midst of renovation work. The problem is that it is not technically possible to make an incision at a 45 degree angle. To perform such manipulations, it is important to correctly dock at the boundaries of the outer and inner corners of the web, which is quite problematic.

The specificity of the ceiling version is not only in the vertical position of the canvas. The mount is placed at the base at an angle of 38 to 45 degrees. The difficulty lies in the implementation of the incision at 45 degrees. It is difficult to connect cut edges from the inside, gaps appear between them, aesthetics are disturbed.

For the most accurate cutting, a special corner element is used, which is inserted into the edge of the skirting board. it will help to hide the cutting errors. This element will emphasize the corners in the room, the choice of such a detail must be approached responsibly.

How to cut a ceiling skirting board without a miter box. How to cut a ceiling plinth correctly

This is how the corners of the ceiling plinth look correctly cut

You can make such an ideal ceiling plinth with your own hands if you follow these instructions.

For the manufacture of ceiling cornices, three materials are mainly used, these are:

They also make stucco ceiling cornices, but this is a different topic.

• The weakest and cheapest of them is polystyrene, although strength on the ceiling is not very required.
• Expanded polystyrene is much denser than it can be easily cut with a knife and, of course, it is more expensive.
• Wood is the hardest to handle. In order for the corners of the wooden skirting boards to be ideal, you must use an exclusively fine-toothed hacksaw, and even better a hacksaw for metal and a sandpaper. Only in this case can you achieve an even angle.

Useful Tips

These tips will help you cut the corners of the baseboards as correctly as possible.

• Before cutting large parts, it is recommended to try on small residues. Having mastered the cutting technique, you can start cutting the real parts of the skirting board.
• As an impromptu version with a miter box, you can use a table pushed against the wall.
• To mark the inner corner, measure the length of the plinth directly from the corner.
• To mark the outer corner, the skirting board must extend beyond the corner by the width of its end.
• We cut the skirting board along the marked mowing line, it should be laid on a hard surface, and not marked side down.
• It is recommended to fix the skirting boards to the ceiling only after both parts have been cut out and their joints have been checked. It can be fixed to the ceiling if, when checking, the corners docked without gaps.
• Minor inaccuracies in joining wooden or polyurethane ceiling skirting boards can be corrected with a file. In foam skirting boards. using a sharpened knife.
• The gap formed as a result of fuzzy trimming can be hidden with a putty.

It is interesting. How to putty a plasterboard ceiling for wallpaper and painting: step-by-step instructions for preparatory work

If, when creating an interior decor in the form of a plinth on the ceiling, you did not have a miter box at hand to cut the corners correctly, use one of the presented methods and you will get a clear and neat corner without gaps.

3 ways to make an inside or outside corner

To complete the corner you will need:

• Ceiling plinth;
• Pencil;
• Sharp knife or fine-toothed saw.

Advice! When cutting, you should not rush, it is better to double-check everything again. this will avoid damage to the material.

To make the correct inner corner you need:

• Attach plinth to corner.
• On the ceiling, along the attached plinth, mark with a mowing line using a pencil.
• Attach the skirting board on the other side. in mirrors.
• Mark with a pencil on the ceiling, just like the first time.
• The intersection of the lines on the ceiling is the elevation of the upper cut point.
• Again took the plinth and attached it to the corner, move the mark of the intersection of the pencil lines.
• Draw a perpendicular with a pencil on the plinth. here are the marks down.
• Cut the edges strictly along the mowing line.
• Repeat p. 6-8 for the second plinth.

Attention! Before gluing cut skirting boards, the cut quality should be double-checked. To do this, attach prepared skirting boards to the corner, if there are cracks at the junction, you can glue it. If unevenness of the joint is noticed, the cut must be corrected.

Cutting the skirting boards should be done carefully, and not applying great effort, so as not to crush the edge, otherwise, after drying, it may deform.

To cut an even angle of 45 degrees, you can prepare a template on cardboard

If the interior corner of the room is 90 °, the skirting boards can be trimmed using a template. For this:

• On the cardboard, draw 2 parallel mowing lines with a distance greater than the width of the plinth.
• Mark the center between them.
• Using a protractor and a pencil, mark the angles = 45 °.
• Recheck the accuracy of the marked angles for coincidence with the real ones.
• Transfer the marks to the skirting board and spray it or spray it, put the lower edge of the skirting board to one of the parallel lines, and set the knife or saw at the marked angle, cut off.

It is interesting. Which porch is better to choose for a private house: an overview

Another option for cutting the inner corner of the plinth at 45 ° without using a miter box:

• Measure the end width of the skirting board.
• Make a mark along the bottom edge of the plinth, at a distance equal to the end width of the plinth.
• Connect the top corner with the mark of the bottom edge with a diagonal line.
• Cut the skirting board along the mowing line.
• Execute p.p. 2-4 on the second bar in mirroring.

When cutting the outside corner, use the following method:

• Attach the ceiling plinth to the corner, so that the plinth extends beyond it.
• Make a mark with a pencil, draw along the ceiling.
• Attach the skirting board on the left to the corner, so that the skirting board extends beyond it.
• Using a pencil, make a mark, draw it along the ceiling with a pencil, to the intersection with the first line. Mark the intersection of the lines.
• Transfer marks to the plinth, connect them with a line, cut off.
• Check the clarity of the joints, put the cut skirting boards to the corner.
• If necessary, correct inaccuracies in trimming, stick.

Attention! To form an outer corner, the cut must point to the inside of the skirting board.

If a gap has formed between the skirting board, it can be hidden with putty

Trimming inner corners with a miter box

To do this, you need the following tools:

• The fillet is laid on the bottom with the miter box with the side that will be glued to the ceiling, and the lower side is pressed against the miter box wall, against its right slots.
• Fillet trimming is done with a hacksaw or a sharp knife. Cut carefully, without excessive force, so as not to deform the ceiling cornice and NOT chipping.
• In this way, cutting off the adjacent corner of the plinth, but already with the help of the left slots on the miter box.
• Then these parts are applied to the corner to check if there is a gap, then you can cut with a knife.

Tip: In order not to translate the material in vain and to acquire skills, practice first on small pieces.

How to properly lay the fillet in the miter box

Trimming adjacent fillets

What is it made of and what is it called

The very first skirting boards on the ceiling were made of plaster. They were cast in special molds, then installed in a solution on the ceiling. Such figured ornaments were called fillets. Today you can see them rarely are expensive, and outwardly they almost do not differ from the cheaper options. And the name is almost lost.

The most popular ceiling skirting boards today are made of polyurethane or polystyrene. They are inexpensive, look great, are easy to install, have a wide range of profiles and patterns. The width can be from 5 mm to 250 mm. They are used in almost any room, decorated in any style. The exception is wooden houses with a corresponding interior. Wooden products are most often used here. the style dictates its conditions.

There is also a similar plastic finish. It is mainly installed in bathrooms. But even in damp rooms, you can safely mount polyurethane strips. they are NOT afraid of damp.

You need to cut the ceiling plinth in the corners of any material in one of the ways described below. The only exception is plastic skirting boards: such a corner can be issued only with the introduction of ready-made corners.

How to get the correct angle

Most of the problems when working with skirting boards arise when making corners. Since the surface in the products is complex, it will NOT work simply to cut at the desired angle: it is also necessary to cut it so that they dock and, preferably, without large gaps. In reality, there are several ways to make the corner of the skirting board Perfect (or almost).

How to cut ceiling plinth in corners

The quality of the ceiling finish greatly affects the appearance of the room. Then they try to do everything perfectly, or very close to it. The finishing touch to the design is the ceiling plinth. They give the finish a complete and holistic look. The strips themselves are mounted on flat surfaces simply: on special white glue, but problems arise with the design of the corners. Without knowing how to make the corner of the skirting board correctly, a lot of material deteriorates. How and what to cut it in the corners and tell you.

With the introduction of miter box

If the corners and walls in the room are even, you can use a special carpentry tool. a miter box. This is an inverted U-shaped chute in which the mowing line is marked for cutting at 90 ° and 45 °. The part in which you need to make a gash is laid inside, a saw is inserted into the guides. The part is held in place, cut to the desired angle.

This is what the miter box looks like. Can be plastic, wood or metal

In the case of a skirting board, not everything is so simple: they must simultaneously lie on two surfaces, therefore they need to be pressed against one or the other wall of the miter box. When working from the ceiling, they are pressed against the side closest to you.

The sequence of actions when finishing the outer corner, you need to make a gash at an angle of 45 degrees. Place the miter box in front of you. I try on how the plinth will be located, determining which part of it will be attached to the ceiling. In order not to get confused and cut off the ceiling plinth correctly, the bar that will be located on the right, We put the case, then that on the left is on the left.

How to cut a corner on ceiling skirting boards: correctly Install it in a miter box

The part that turns out to be on the ceiling presses against the lower part with a miter box. The other side is closer to you and raised. She is supported on the wall of the device so that she does not stagger when cutting. That is, the front of the skirting board turns out to be turned away from you. Do the cutting direction as shown in the photo below. By folding the two cut pieces together, you get a Protruding. Outside or Outside Corner.

How to Make the Outside Corner of a Skirting Board Using a Chair

First put the cut-off parts in place “dry”, without applying glue. If the geometry of the corner turned out to be not ideal for centuries, you can touch up a little with a knife. It is easier to cover small errors with a special putty.

The situation is very similar with the inner corner of the skirting board. First you try on which side will be on the ceiling, this part is pressed to the bottom with a miter box, the second part is supported on the wall closest to you and cuts as shown in the photo below.

How to make an inner corner of a ceiling plinth with the introduction of a miter box

And again, at first I try it on without applying glue, if necessary, I slightly correct it. Then apply a thin bead of glue to both surfaces that will stick to the wall or ceiling.

Your own version of how to use the miter box correctly is shown in.

What and how to cut

Working with skirting boards made from different materials means using different cutting tools. When working with a wooden skirting board, it is more convenient to work with a saw on wood. All others, including plastic, made of foam and other polymers, are better cut with a metal sheet. The result is a smoother cut, less burr. Saws are usually used when working with a miter box.

Corner design looks attractive

When working with a polystyrene skirting board without special tools, they cut them with a good office knife. Its blade is quite thin and even, the cut is smooth, wrinkled. If you use a saw with hydro- or polystyrene, do not press hard: you can wrinkle.

In general, in order to get used to the tool and material a little, take some piece and practice on it: cut, saw, trim. So there will be fewer problems when working.

How to make a corner of a ceiling plinth without a miter box

Few people in apartments or houses have angles of exactly 90 °. Small deviations are easily corrected after fitting. But not always. Then you have to mark everything “in place”. under the ceiling.

You will need a finely contoured pencil (hard. it is not so visible on the ceiling, but leaves quite clear marks near it), a small piece of plinth, a ruler and a good stationery knife if you work with polyurethane (polystyrene) baguettes or metal dust to work with other materials.

Apply the plinth to the corner, draw along the outer edge with a pencil. Apply to the other side of the corner, also mark. You have a cross on the ceiling, the center of which marks the place where the plinths of the ceiling plinth should converge (look at the photo). I installed a piece of plinth in the corner, which will stick there and resting it with its end on the wall, transfer the mark to it.

How to make corners on skirting boards without using special tools

Now take a ruler and connect the edge of the skirting board with the marked mark. If you just put the plinth on the table and cut along the mowing line, the two parts in the corner will still NOT fold: the inner part will interfere. You can trim it later, try it on the ceiling. The second way is to install a piece that needs to be cut on the table, then a piece that will be on the ceiling. And cut along the mowing line, but keeping the knife at an angle of about 45 °. It will still be necessary to correct, but much less (and less chance of error).

Repeat the same operation with the second bar. Attached to the desired wall, abuts the butt against the adjacent wall, mark the place where the cross is drawn, draw the line and then Cut it off. Correction Carried out “dry” without applying glue.

You repeat exactly the same steps for the outer (protruding) corner. Now you know one more way of how to make a corner of a ceiling plinth, and without a scissor or other special devices.

With decorative corners

There is one more, simpler way. For skirting boards made of polyurethane or polystyrene, use ready-made, factory decorative corners. They are installed in a corner, strips are glued to them closely. Cutting them if necessary is very simple: a few millimeters with an ordinary clerical knife.

Examples of finished corners for fillets

How to join in corners

If the installation of the first corner is completed, we can assume that you have already learned almost everything. “Almost”, because you still need to learn how to join the corners and cut the planks to length. When some part is already glued and a small distance is left to the corner, how not to be mistaken with the length? The answer is simple: leave stock.

At first, you can cut a piece 10-15 cm longer: it will be possible to redo it several times if something does not work out right away. Then you make the corner in the way described above, try it on dry, adjust everything so that the result suits you. Only then can the already cut bar be attached to the corner and mark the place where it can be shortened. You need to trim at exactly 90 °. It is not necessary to use a miter box. Just try to put the knife (hacksaw) perpendicular to the surface.

Features of cutting ceiling plinths in a miter box

It is necessary to work with this device extremely carefully so as not to blunt the tool and leave no cuts in unnecessary places. In the process, we adhere to the following instructions:

We fix the baguette in the miter box in the same way as it is planned to place it on the wall. The side that will press against the ceiling on the miter box should lie against the sidewall.

We insert a cutting tool (hacksaw or knife) into the desired gap and cut the fillet.

We process the joint of the ceiling plinth and apply it to the wall to check the correctness. The foam molding can be tweaked with a sharp knife if the roughness of the end is about 2 mm. The wooden skirting board can be simply sanded with sandpaper. For ease of use, it can be glued to a wooden block.

How to cut a ceiling plinth

One of the most difficult steps in installing skirting boards is cutting them correctly. Only by correctly joining the individual elements at the outer and inner corners will you get the desired result. Fillets will look aesthetically pleasing and neat if you cut them off at the right angle and seal the cracks. A special tool (miter box) is used to accomplish this task. And if it is not there, then other devices will help.

Cutting technology for ceiling plinths

For efficient and high-quality work, you need to choose a tool in accordance with the material of the baseboard and choose a cutting method. If you have a miter box, then there will be NO special difficulties in the process. If it is not there, then two options are possible: cut according to a template and measure on the ceiling or make this tool yourself.

Method of cutting the ceiling plinth without miter box

To neatly dock fillets in the inner corners, you can do without a miter box.

We carry out the work in the following order:

We attach the end part of the baguette to the letter of paper and outline the contour of the convex side. It is more convenient to use a small piece of plinth (if any).

Cut out the resulting template.

We transfer the contour to the surface of the baguette with a simple pencil.

Cut along the drawn curve.

For fitting, one plinth is applied tightly with the end part to the wall, and then the second.

If there are small gaps, then they can be processed with a clerical knife or sealed Subsequently with a sealant.

Technique for cutting ceiling skirting boards

This method can be used if your corners are even and you want to trim the baguette exactly 45 degrees. To do this, before cutting the ceiling plinth in the corners, you need to draw a miter box on thick paper. Draw two parallel mowing lines and mark the angles at the desired degrees using a protractor.

Placing the fillet in this case in the same way as in the traditional miter box. Please note that you need to cut the skirting board while holding the tool in a strictly vertical position.

Selection of tools for cutting ceiling skirting boards

To properly and accurately cut the ceiling plinth, you need to use a suitable cutting tool. It is chosen depending on the material from which the fillets are made:

Styrofoam. It is characterized by low strength and is inexpensive, and then foam models become more and more popular. Their strength does not particularly affect the performance, since usually the ceiling plinth is NOT subjected to mechanical stress. A regular stationery knife is suitable for cutting.

Extruded polystyrene foam. A cheap material with a density several times higher than that of foam. Because of this, cutting it is a little more difficult, and then a sharp and thin knife is used for THESE purposes.

Tree. Such skirting boards are more difficult to process, although they have many advantages (environmental friendliness, strength). They are more expensive,
especially if made of hardwood. Before cutting wood ceiling plinths, stock up on a hacksaw.

In addition to the tool for direct cutting of the baguette, you will need a miter box. This is a special device made of wood, plastic or metal in the form of a box with sawed off the sides. A hacksaw or knife can be inserted into it at the desired angle. Thus, the cutting angle is as accurate as possible.

We knock three planks of 5015 cm with a long edge into the shape of a three-sided, rectangular box. Please note that an angle of 90 degrees must be respected between the side rails and the transverse board.

Using a protractor, mark an angle of 45 degrees on the bars. Instead of a protractor, you can use a school square. In it, one angle is 90 degrees, and the other two are 45.

Before cutting corners, mark the vertical direction with a simple pencil.

Rules for cutting ceiling plinths by marking

This method is used to cut skirting boards in cases where there is neither a miter box nor parts from which it can be made.

To do this, you need to make markings on the wall in this order:

We put the baguette in the corner to the place of fastening.

Along its one edge, we draw the base line on the ceiling for the level of attachment.

We apply the fillet in the same way to the perpendicularly drawn mowing line on the ceiling and again draw a straight line along one side. We should have two segments, which intersect at one point.

We again apply two plinths in turn and mark this point on them.

We repeat the same procedure now on the wall to mark on the products the place of cutting from below.

We connect two points with a line. It can run at an angle of 38-45 degrees, since walls and corners in living rooms are often uneven.

Cut off the baguette along the mowing line.

Tips for cutting ceiling plinths

When working with a miter box, there are two things to consider:

The inner corner of the ceiling plinth is formed from two parts: the first we start the case in the miter box and cut from right to left, the second we start from the left and cut from left to right.

We start the first part of the outer corner from the left and cut off from right to left, the second we start the case and cut off from left to right.

In addition, you need to know the following nuances before cutting the skirting board:

Before you start cutting a baguette with a miter box, try cutting a test strip to avoid mistakes.

You can make the correct measurements by measuring the length of the inner corners of the plank on the inner side, and the outer ones. these are the points of the inner corner for the width of the fillet deep into the room.

If the baguette is installed under a stretch ceiling, then it should only be attached to the wall. The adhesive composition should never get onto the vinyl sheet.

The final fixing of the skirting board should be carried out only after the exact fit of the plank.

If the corners and walls in the room are even, then you can customize it on the floor.

When installing baguettes, it may be necessary to adjust them several times, therefore, stock up on tools and patience.

Instead of a template and a miter box, you can cut in the corner between the wall and floor, or by moving the table against the wall. In this case, on the wall, ceiling and bug, you need to mark the cutting angle of the end.

If you are interested in the question of how to cut a ceiling plinth without a miter box, and you do not have time to use templates, then you can purchase special corner inserts in advance. They will hide the gaps, but will protrude and stand out on the coating.

If you have a skirting board made of precious wood, then you need to cut and install it very carefully, since a large amount of putty for sealing the joints will be too noticeable, and painting over the baguette is an inappropriate solution, because this way you will hide the natural texture of the solid wood.

Expanded polystyrene products do not have to fit close to each other due to the soft texture, but wooden and plastic models must be well docked.

If the trapezoidal niches on the wall need to be bypassed from above with a plinth, then we join the walls at an angle different from the straight.
In this case, cut off the plinth at an angle equal to half the joint. For example, if the walls are joined at an angle of 120 degrees, then we cut the fillet at an angle of 60 degrees.

How to cut a ceiling plinth. look at:

Outside corner

• Measure the length of the plinth from the nearest wall to the outer corner, leave the fishing line on the wrong side with a pencil, indicating the desired length. It should be noted that the edge (its upper part) should extend slightly outward.
• The plinth is moved to the miter box and cut off.
• The adjacent strip also needs to be measured with a margin and cut off in a mirror image to the first part.

Trying on a ceiling plinth: the joining of the parts should be perfectly even. If the result is not achieved and there are irregularities at the joint, you can trim the edges with an ordinary knife to a perfect joint.

Checking the smooth docking

All the nuances are well described:

How to cut the corner of a ceiling plinth straight

A beautiful and neat edging of the ceiling hides the joints of the border with coverings and is an additional element of the room’s decor. But in order for the ceiling plinth to look really beautiful, you need to be able to qualitatively join its corner joints.
How to cut the corners of the ceiling plinth evenly can be found in our article.
Related article: how to properly glue the ceiling plinth with glue and putty.

Method two. no additional tools

For the inner corner, you can use the simplest way of perfect joining. by marking on the ceiling. Another example of how to cut a corner nice and even.

• Apply a fillet to the ceiling, tightly presses its even edge into a corner.
• Draw a line along the long side of the plinth on the ceiling.
• The same action is done with the adjacent part on the other side.
• Mark the point of intersection of lines.

In total, you get an even angle of 45 ° if you draw the line from the point of intersection to the edge of the part. Note that the above method of marking works only at perfectly flat corners.

The first way is with a miter box

The miter box usually looks like a tray with vertical holes for a hacksaw. It can be made of wood, metal or plastic. This tool is the oldest and simplest carpenter’s tool for cutting wood pieces at 90 ° and 45 °. There are types of such a device for professional work, with a swivel mechanism, in which the cutting tool can be rotated and fixed in any position.

How to cut a ceiling plinth correctly

Ceiling corners are divided into internal and external, the method of joining them is slightly different.

Inner corner

• We make the right measurements.
• We install the plinth plinth in the miter box so that this position exactly coincides with the placement on the ceiling.
• The plinth should be firmly pressed against the opposite wall of the miter box. Hold and press with your free hand.
• We put a hacksaw at an angle of 45 ° in a special hole and cut off the part.

The adjacent part must be cut in the same way, only in a mirror image, as shown in the photo.

other methods

With a good eye and accuracy of hand action, you can use a homemade template that resembles an imitation of a miter box. To do this, take a thin board or thick plywood and draw a layout in the form of a horizontal rectangle. Using a protractor, mark 45 ° on the right and left sides of the rectangle. Mowing line lines connecting opposite edges. You can now cut the ceiling plinth using this layout. The actions are simple and similar to the description above in the first option. Only the ceiling parts should NOT be inserted, but put on the drawing and combine the hacksaw with the layout of the layout.

Special accessories for docking