Category: Articles

Trigger Petrol Whirlwind Does Not Start

In general, such a conversation should start with the fact that after buying a garden gasoline tool it would be better to first familiarize yourself with the instructions attached to it. Then many problems could have been avoided. But since this happened the gas trimmer does not start, then we must look for sources of inoperability. And in this article we will consider the main reasons why the trimmer does not start with the example of the Elitech T750 model, as well as describe general recommendations for the operation of such a tool.

Start with the banal! We will figure out how to properly start a gas trimmer. It may be that the reason lies precisely here.

First you need to bring the red toggle switch on the trimmer bar to position "I". This means turning on the power.

Trigger Petrol Whirlwind Does Not Start

Then you need to switch the fuel supply lever on the carburetor and use the “suction” button of fuel (similar to a pipette, located on the carburetor). This is necessary to supply gasoline to the engine. Return the fuel supply lever to its original position. Finally, pull the starter handle toward you sharply. The trimmer should work. Try several times if the first time fails. If after such manipulations the situation has not changed and the gas trimmer does not start, then you should first examine it yourself before leading to the service center. There are two main reasons why a garden trimmer will not start:

  1. Violation of the power circuit.
  2. There is no fuel.
  • Let’s start with the ignition problems. In most cases, it is caused by the need to change the spark plug in the engine. It is done like this:
  • First of all, we must take care of security measures, make sure that the trimmer is turned off. We bring the above toggle switch to the "STOP" position.
  • Then remove the rubber protection from the plug and the wiring terminal. Using a special candle key, we unscrew the spark plug and replace it.
  • After that, we assemble the device and carry out the procedure for trimming the trimmer described above.

The second reason the garden tool doesn’t work is because the fuel has run out. On the Elinech T750, a fuel tank is located near the motor, but on most trimmers it is there. We unscrew the cap from the tank and fill it with gasoline (the most optimal option is the AI-92, it is inexpensive and does not clog the carburetor like the AI-76). Do not forget to add special engine oil to the tank, just 50 grams per gas tank is enough, without it the motor will begin to “sneeze” and will quickly become worthless. After we close the tank with a cap, wipe the surface of the trimmer and our hands with a dry cloth. We also do the above manipulations to turn on the garden tool.

If the gas trimmer does not start as before, then it makes sense to return it for repair. And the reason for this decision is simple – if you do not have the appropriate skills, repairing the equipment is almost impossible.

In order for the tool to serve as long as possible and there are no such malfunctions, you should, first of all, familiarize yourself with the instruction manual for the trimmer. Also, pay special attention to the operating time of the engine at the trimmer – take a short break every 15 minutes of operation and, finally, properly care for the tool, wipe it after work, lubricate it with graphite grease. Observing such simple rules, you can significantly increase the life of the tool and it is quite possible that you do not have to look for reasons why the gas trimmer will not start.

36,291 total views, 32 views today

Source
  1. Diagnostic Features
  2. Main reasons
  3. Troubleshooting Methods
  4. Recommendations for use

Given the specifics of using gas trimmers, their owners quite often have to deal with certain problems. One of the common troubles is that the lawn mowing does not start or is not gaining momentum. For the most prompt and effective elimination of such a problem, one should have an idea of ​​the main causes of possible malfunctions.

Diagnostic Features

Trimmers can be attributed from a technical point of view to complex devices. Based on this, Before using them, it is strongly recommended that you carefully read the relevant instructions.. However, in practice, many ignore it, often then find themselves in situations where the gas trimmer does not start or is poorly gaining momentum during operation. It is worth noting that similar problems can be encountered when acquiring new models of equipment.

The key to effective and efficient repair will, of course, be competent diagnosis of the device. In the process of troubleshooting, you will have to inspect and test, first of all, the key elements. The list of such includes candles, tank, filter units and valves of the fuel system. As practice shows, very often malfunctions of these particular elements become the reason that the lawn mowing does not start. Special attention should be paid to the quality and correct preparation of the fuel mixture, especially when it comes to two-stroke engines. In relation to this parameter, the manufacturer’s recommendations should be strictly followed in order to avoid serious breakdowns and costly repair work. In the case, for example, with a piston ICE group, costs can amount to up to 70 percent of the cost of new equipment.

Often owners of trimmers have to deal with situations where the specified mixture is high-quality, the carburetor is serviceable and tuned, and the device still does not show signs of life when trying to start the engine. In such cases, you should check the condition of the candle. The following steps will fix the problem:

  1. Turn out the candle;
  2. Wipe and dry the part (calcination is undesirable);
  3. Remove fuel and dry the candle channel for 30–40 minutes; such actions will avoid filling the candle with the next attempt to start;
  4. Completely eliminate traces of soot using a file or sandpaper;
  5. Set the appropriate clearance;
  6. Put the candle in place.

If the candle turned out to be working and the seat nest is completely dry, and the engine of the scythe does not start, then wet the threads with gasoline. It is worth remembering that regardless of the quality of the spark issued, initially in a completely dry chamber there will simply be nothing to ignite. Faced with the fact that the spark does not come, it is worth paying attention to checking the contact between the high voltage wiring and the candles. If this connection turns out to be of high quality, then it will be necessary to check the operability of the ignition system control unit. In such cases, it is unlikely that you can do without the services of a qualified specialist.

The next step in diagnosing a gasoline braid will be to check the condition of the filters. Often the lawn mower does not start well or does not start at all in the cold because the air filter is clogged. This malfunction can be detected by excluding it from the system. If after this the braid starts up, you will have to clean or change this element. Experienced users strongly recommend periodically blowing the air filter to maximize its life.

The described tool may also not start up due to problems with the supply of gas caused by the contamination of the fuel filter. To quickly and effectively eliminate such a breakdown, you just need to replace the filter element with a new one. It is important to remember that the suction nozzle must be equipped with a filter, which is provided for by all instructions. Failure to comply with these rules and recommendations may result in costly piston repairs. In the process of diagnosing and finding the source of problems with starting the mower, attention should be paid to the breather, which is responsible for stabilizing the equalization of pressure in the fuel tank. In addition, it is necessary to check the cleanliness of the exhaust channel and the silencer mesh. As a rule, similar problems are most often encountered when troubleshooting old models.

Main reasons

As practice shows, gas trimmers cease to start or function normally after winter, that is, long-term seasonal storage. Before subsequent attempts to start the tool, a thorough diagnosis should be made to determine the source of the problem. There are currently some of the most common causes of a malfunction.

  • Initially, it is necessary to check the quality of the fuel. Savings in such cases can have extremely negative consequences. Experienced lawn mowers and experts advise you to prepare a mixture, the volume of which will correspond to the upcoming work, since its surpluses quickly lose their quality.
  • Trimmers of such famous brands as, for example, Husgvarna, Makita, Stihl, are very sensitive to the fuel used. It is about fuel quality and octane rating. Providing suitable operating conditions and extending the service life of the equipment will allow refueling with high-quality gasoline.
  • At the moment of starting the engine, the lawn mower may stall due to the fact that it fills the spark plug. Often in such situations, you have to deal with the need to adjust the carburetor. It is worth noting that similar problems arise when the braid ceases to start on a hot one.
  • Sometimes the tool cannot be started, although the candle is wet, which in turn indicates the flow of the fuel mixture into the combustion chamber. This is usually one of the symptoms that there is no spark. The reasons may be the lack of normal contact between the candles and the high-voltage wire or the drying of the threaded connection in the candle channel.
  • If there are no problems with the spark, while the candle itself remains dry, then most often this indicates that gasoline is not pumping. There may be several reasons for this. This, in particular, is about the state of the fuel filter and carburetor.
  • The ICE of the braid does not start or immediately after starting stops working, which may be due to clogging of the air filter that impedes the normal supply of air necessary for enrichment of the mixture.

Video: Trigger Petrol Whirlwind Does Not Start


Troubleshooting Methods

It is no secret that the best and most effective way of repair is to prevent possible malfunctions. As already noted, one of the key points is how correctly prepared the gasoline-oil mixture. Its components must be gasoline no lower than AI-92 and high-quality motor oil. The proportions, taking into account which the mixture is prepared, are indicated in the manufacturer’s manual, which is supplied with any gas trimmer. As a rule, oil is added to gasoline using an ordinary medical syringe. Similarly, it is easiest to maintain appropriate proportions.

Quite often, when problems arise with the start of lawn mowing, the owners of the tool try to make repairs with their own hands. With the necessary knowledge and skills, this approach will significantly reduce operating costs. First of all, it is worth checking the fuel system and, in particular, the filter element. If clogging is found, the easiest way to replace the filter is with a new one. If the air filter became a source of problems, then you can get out of a difficult situation even in the process of work with insignificant time costs. You will need to perform the following steps:

  1. Remove the filter element;
  2. Directly under operating conditions, you can rinse the filter with used gasoline;
  3. When using a scythe at home or in a summer cottage, water and simple detergents are used for cleaning;
  4. After washing, the part is thoroughly rinsed and dried;
  5. A completely dry filter should be lubricated with engine oil;
  6. Excess lubricant is removed by compressing the filter element with your hands;
  7. Put the cleaned part in place and fix the plastic cover with screws.

If the described actions did not provide a positive result, then the next step is to adjust the idle speed using the appropriate carburetor screw. This topic is devoted to many publications and videos posted on the World Wide Web. When trying to solve the problems in question, you can take several steps.

  1. The trimmer is placed on its side so that the “air” is on top. This will allow the fuel mixture to enter the bottom of the carburetor. Often, attempts to start the engine are successful if you first dismantle the part and literally send a couple of drops of gasoline directly to the carburetor itself.
  2. If, after all the described actions, the braid could not be brought into working condition, then attention should be paid to the condition of the candle and, in particular, to the presence of a spark. In parallel, all fuel is completely removed from the combustion chamber.
  3. Often the owners of a lawn mow are in situations where the fuel and air filters are clean, the candles are working, the fuel mixture is fresh and high-quality, but the ICE does not show signs of life. In such cases, experienced professionals recommend using the universal and proven long-term practice launch method. It is necessary to put the choke in the closed position and pull the starter handle once. After the shutter opens and the engine is started 2-3 times. In the vast majority of cases, the result is positive.

The spark plug in the process of starting the internal combustion engine trimmer can fill with fuel. Even with a high-quality mixture and a good spark, it is unlikely to get a device. The most effective way out is to remove the candle and dry it. At the same time, this spare part can be checked for operability; if a malfunction is detected, replace it. This procedure includes a number of simple steps, namely:

  1. Switch off the device and wait for the power unit to cool completely;
  2. Disconnect the wire;
  3. Remove the candle itself;
  4. Inspect the dismantled part;
  5. Make sure there is a gap (0.6 mm);
  6. Screw in a new, working candle and tighten it.

In practice, many repairs related to the fact that the scythe has ceased to start and which sooner or later have to be encountered in the process of operating a household lawn mowers can be handled independently. But in case of serious malfunctions, it is most rational to contact a specialized service. However, the key factor in such cases will be the ratio of the cost of repair and the price of a new trimmer.

Recommendations for use

The stability of any lawn mowers and the absence of problems with starting the power unit of such devices directly depend on the conditions in which the tool is used and the quality of maintenance. And we are talking about the following basic rules:

  • In the process of work it is necessary to pay special attention to the cooling system and other elements; It is strongly recommended that you clean the channels located on the body of the braid and starter ribs in a timely and high-quality manner;
  • In the processing of various elements, you can use solvents, gasoline, kerosene and other effective means;
  • These works should be carried out after the power unit has completely cooled down;
  • It is necessary to fully comply with all the rules specified in the relevant instructions drawn up by the developers of the described tool, which will avoid overloads in a warm engine, which in turn is the most common cause of serious damage;
  • All residual fuel in the internal combustion engine should be completely drained before long interruptions in the operation of the spit; it should be borne in mind that the gasoline-oil mixture quickly decays into so-called heavy fractions, which inevitably clog the carburetor;
  • After removing the fuel, it is required to start the engine and let it run on the twentieth until the moment it dies out; similarly, the remnants of the mixture will be eliminated from the internal combustion engine in full.

Particular attention should be paid to preparing the instrument for long-term seasonal storage. This should be done in order to minimize the risks of problems starting the engine. Competent preparation includes the following manipulations:

  1. Completely disassemble the trimmer;
  2. Thoroughly rinse and clean all the elements that are accessible;
  3. Inspect the details of the lawn mowers in order to identify defects (mechanical damages discovered in this case should be eliminated);
  4. Pour engine oil into the gearbox;
  5. To carry out high-quality cleaning from clogging of the air filter element;
  6. Having the corresponding knowledge and practical skills, it is possible to perform a partial disassembly of the power plant with subsequent purging and lubrication of the moving elements;
  7. Wrap the collected gas spit with a pre-oiled rag.

In addition to everything already listed, it is necessary to lubricate the piston group. This algorithm provides for the following simple manipulations:

  1. Remove the candle;
  2. Use the starter to move the piston to top dead center (TDC);
  3. Pour a small amount of engine oil into the cylinder;
  4. Crank the crankshaft several times.

Regardless of the cost and brand of equipment, you should clearly follow all the requirements of the relevant instructions and adhere to the recommendations of developers and experienced professionals. Today, detailed information regarding the proper use of such technology can be easily found on many specialized sites and forums.

Next, watch a video on how to identify and eliminate the reason why the gas trimmer does not start.

Source

Like any technique, trimmers are prone to various breakdowns. Often at the beginning of the summer season, owners of such an instrument complain that the trimmer does not start, and it takes a long time to look for the cause of the malfunction.

For those who have recently acquired a trimmer and are still at the “you” with this technique, information on why the trimmer does not start and what to do in this case will be useful. So, let’s find out what could be the reason for this.

Gas Trimmer Does Not Start – 10 Possible Causes

Before trying to independently adjust the tool, carefully read the manual for its operation. Perhaps the information contained in it will lead you to one or another thought. Otherwise, you will have to look for the cause of the malfunction by the selection method. It may be one of the following:

  1. The toggle switch on the bar is not translated to the "On" position. This is one of the elementary actions, but sometimes beginners forget to turn on the tool before starting it.
  2. Similar errors include the lack of fuel in the tank. If the fuel runs out, but you forgot about it, just fill the tank (usually located near the engine) with AI-92 gasoline.
  3. Lack, improper mixture or wrong proportion of engine oil. Ideally, not more than 50 g of oil should be added regularly. This will provide additional lubrication and will keep the engine of your trimmer in working condition. Also keep in mind that there are different types of oil (“synthetics”, “semi-synthetics”, “mineral water”) – they all affect the mechanism in different ways.
  4. If the trimmer does not start after winter, drain the remaining fuel in the gas tank and replace it with fresh fuel. This is especially true for small, low-power trimmers with small motors that are sensitive to poor-quality mixes. In addition, during the winter, sediment may form at the bottom of the gas tank, which causes problems with the operation of the device.
  5. Excessive pumping of fuel can also be one of the reasons that the trimmer stalled and does not start. When the air damper is closed, the candle is filled with fuel. It should be unscrewed and dried, and then inserted in its place and try to start the engine, holding the trigger of gas. It is advisable to check it beforehand for the presence of a spark between the electrodes. If there is no spark, the candle should be replaced.
  6. Problems with the filter. If your trimmer does not start well, remove the air filter and run the tool without it. If everything worked out – the filter should be replaced with a new one. As an option, thoroughly clean and blow through the old one, but anyway, sooner or later you will have to make a replacement.
  7. Is the trimmer dead and won’t start? Try to clean the so-called breather – an element designed to equalize the pressure in the gas tank. Cleaning can be done with a regular long needle. A clogged breather often causes a malfunction.
  8. Knives have been removed from the machine – some models will not work under this condition.
  9. Violation of tightness. This can be checked using a manometer. If the pressure starts to drop, you should determine which part of the carburetor is faulty. Most often, the carburetor gasket wears out.
  10. Sometimes after a long period of work, you may notice that the trimmer is overheated and will not start. First, you should know that you should definitely take breaks. The amount of continuous time recommended for this model should be indicated in the instructions. Also, the problem of overheating can lie in a faulty ignition coil or in an air cooling system that prevents overheating.

If none of these actions gives a result, you should contact a repair shop or service center.

Source
Articles , , , ,

Reviews Hitachi Cg27eas

Reviews Hitachi Cg27eas

Long shoveled the Internet. Since mowing on an industrial scale was not expected and the spit is needed for domestic needs and easy to transport, he was inclined to a compromise of 27-30 cubes, but a good brand and a reliable model.

The car (class C-D) in a fully assembled state enters without problems with one folded back of the rear seat.

Purchased:
– trimmer head "Husqvarna" T35 (holds more fishing line, easier to refuel)
– lightweight milling cutter with tv. teeth D230 mm. (perfectly mows small overgrowth of trees with a diameter of up to 5-7 cm.)
– safety helmet with mesh "Champion" (flies from the braid strongly, so the mesh covering the face to the chest is what you need)
– 90 m. Husqvarna Whisper fishing line 2.4 mm. (really silent compared to the fishing line from the kit and mows perfectly)
– Liquid Moli oil for 2-stroke engines (art. 3958). By the way, it may be due to good oil (gasoline 95th Ecto from Lukoil) that the smell is not felt at all at work.

For work:
Scythe is ready to go. Everything is oiled, just collect, season and go. Started up without any problems. I don’t take off the suspension on a hot one: it starts easily and immediately. Conveniently.
Start (starter) is very soft, do not lie in the description. The sound of work is pleasant, but with a long work the ear plugs / headphones will not be superfluous.

Video: Reviews Hitachi Cg27eas


There is enough power for everything. The main thing is to keep the revs (in addition, it is necessary for 2-stroke engines, to cool them) The tank is small, but since it is better not to store the scythe with gasoline and always fill the fresh mixture, this is it. And she eats very moderately: 0.5 liters is enough for an hour of measured work.
The native 3-blade knife works well on weeds and overgrown, less than a finger thick. Where the thickness is greater, the milling cutter works great.
Scythe really like.

I have been using a scythe for 4 years, I bought for mowing a plot of 20 hundred. Very satisfied, the feeling of use is only positive. The start-up is light and elastic, starts from 1-2 times even after winter. Vibrations are minimal, mowing comfortably for 2-3 hours in a row. Calm F55, loses a lot in all respects (though Calm is a bit more powerful) In general, I recommend this model for purchase.

And now I’ll tell you how to get rid of the problem of twisting the spring:
This year, he himself was faced with turning a spring in the starter (the cord stopped returning). Service trips did not solve the problem. They confirmed that this is a massive sore of this model. They suggested simply replacing the spring and waiting for a new turn.
Rummaging through the Internet, a solution was nevertheless found. precisely, as many as two:

1st METHOD: Cheap solution to the problem. We throw in the spring, glue the ratchet to the drum with glue. Degrease and strip with sandpaper, and glue. Glue is required on an epoxy basis. For example, poxipol or mannol is two-component. Everyone who did, did not see more problems with the starter. The only drawback of this method is the complexity of the subsequent replacement of the lace. Well, I do not consider it a problem, the lack of elastostart.

2nd METHOD: correct, but requires straight arms and 600 rubles. We buy for 600 rubles. repair kit ratchet / pulley. Here is his number: 6699691 (the number is easily looked up in a search engine). We take out the old, put the new one and use it! There will be no more problems with the spring at all. Why services do not know about this repair kit and do not install it, I do not know, but I guess;)

Source
Articles , ,

Normal fishing line, but the price is high!

Normal fishing line, but the price is clearly too high!

All owners of trimmers fishing line refers to consumables. During the season, you can even use more than 100 meters. Therefore, the consumption of fishing line directly depends on its quality. It’s not very convenient to constantly refill the trimmer coil.

Normal fishing line, but the price is high!

At the same time, the packaging is clearly not expressive. But the seller actively trumped the manufacturer, Italy.

Distinctive characteristics of SIAT fishing line from other manufacturers:

  • High degree of wear resistance.
  • Efficient operation at high temperatures and loads.
  • A single diameter for the entire length of the thread.
  • A wide variety of diameters and sections.
  • Saturated color.
  • During prolonged storage and at low temperatures, it does not exfoliate and does not lose its qualities.

In fact, it turned out that despite the fact that Italy was declared on the packaging, this is a marketing ploy. Made fishing line in China. But the brand is Italian.

In any case, it is strange to write down the producer Italy in the pluses, because in any case, it is not some kind of expert in forest production.

Country of Origin China

Although I experienced many curly woods (star, square, triangle, circle, and even wicker), more often I choose a square. Of course, we are talking about fishing lines up to 2.4 mm thick.

Video: Normal fishing line, but the price is high!


It has long been concluded that saving in quality. The more elastic the fishing line, the longer it lasts. Therefore, it is sometimes better to overpay and take more expensive. Although the price is not always an indicator of quality.

If the fishing line is 3 mm thick, then I take an exclusively round section because on the "squared" The mower is tight.

In the case of thin fishing line (2-2.4mm) I do not pay attention to the form.

Everyone chooses the thickness of the fishing line to their taste. If a thin fishing line goes easily along the grass, but then it is spent quickly. A thick fishing line mows more complicated and gives more load to the mower motor, but it is spent economically.

In the case of 2.4mm fishing line, an average option is obtained. By the way, there are options with metallization, but this is a common advertising move and metal sawdust does not affect the durability in any way. fishing line torn from torsion, not from rubbing.

2.4 mm square cross-section

Fishing line length 15 meters

This version of fishing line wound well on the bobbin of the trimmer head.

This time the fishing line was successful. This is the case when the overpayment was not in vain. Mows without problems, moderate consumption.

What is the result?

Despite the not expressive packaging, the fishing line was not bad. This is the case when the appearance does not match the content (for the better).

I’ll take off one star for cheating the buyer in terms of the manufacturer. Like it or not, it’s China and not some Italy. If the manufacturer was honest, then the price of the line was lower and would get its 5 stars.

Source
Articles , , ,

Instructions for running and operating a 4-stroke engine

What you need to know about the running-in and operation of four-stroke air-cooled gasoline engines installed on garden, construction and road motor vehicles.

Gasoline four-stroke air-cooled engines are widely used in landscape gardening equipment. motoblocks, motor cultivators, lawn mowers, snow blowers, motor pumps, mini-tractors, on construction and road-building equipment. gas generators, vibrating plates, rammers.

Before starting engine operation LEARN INSTRUCTIONS FOR USE. Many buyers, unfortunately, do not. Therefore, the most basic questions on the use of the motor arise.

TIP: READ ENGINE OPERATION MANUAL.

First: what kind of gasoline should be used.

We recommend the use of clean, fresh, unleaded gasoline with an octane rating of AI92. Air-cooled engines are not designed for use with AI95 and AI98 fuels. The 95th and 98th gasoline contains additives that have a detrimental effect on the piston system of the engine, leading to overheating and breakdown.

Do not mix oil with gasoline. This may result in engine malfunctions that are not covered by the warranty.

USE FRESH AI-92 GASOLINE WITH A PERIOD OF STORAGE FOR NO MORE THAN 30 DAYS.

Secondly: what kind of oil is poured into the crankcase.

Many people consider automobile oil of well-known brands to be the best for use in engines for a motoblock (motor cultivator, snowmobile, electric generator, motor pump, etc.). This is completely wrong. Car oils are designed to work in water-cooled engines, not air. The boiling point of automotive oils is lower than that of oils that contain special additives for air-cooled engines.

Use oil with a quality class of SF, SG, SH, SJ, CD or higher. Do not apply oil additives. Select oil viscosity based on ambient temperature.

SAE 30 (5 ° C and above) is recommended for temperatures above 5 ° C. When used below 5 ° C, it can cause a difficult start.

10W-30 (-18 to 38 ° C) is recommended for variable temperatures. This oil provides a cold start to the engine, but can lead to increased oil consumption at temperatures above 27 ° C.

Check the oil level more often at elevated air temperatures.

Synthetic 5W-30 (-30 to 40 ° C). Synthetic oil provides engine operation over the entire temperature range, as well as easy starting and low oil consumption.

5W-30 (5 ° C and below) is recommended for use in winter conditions.

FILL OILS ONLY SPECIFIED IN THE INSTRUCTIONS FOR THE ENGINE.

Video: Instructions for running and operating a 4-stroke engine


Always check the oil level. The level should be at the last thread of the filler neck in the horizontal position of the engine (as shown in the figure). Fill and drain holes are located on the front and rear of the engine.

Engine Oil Fill Level

On lawn mowers, pay attention to the dipstick. On the engine probe with a vertical shaft, marks are indicated.

Different engines have different crankcase volumes. If you have a 4, 5.5, 6.5 or 7 hp engine then you need to pour 600 ml. oils. In engines of 7.5 hp poured 900 ml. In engines with a capacity of 8, 9, 11, 13 and 15 hp respectively 1.1 liters.

Third: starting the engine.

At the first or cold start of the engine, an increased load on the piston system occurs. High speeds can damage the motor. Therefore, it is necessary to start the engine at 1/3 of the gas position. And you need to run in at medium speeds.

Fourth: how the engine breaks in.

Air cooled engines "do not like" idle move. Start the engine, warm up for 1-2 minutes. and run in work. During break-in, try to adhere to 50-75% of the load and take mandatory breaks in work after 20-25 minutes. After a break, when the engine has cooled down (15-20 minutes), you can continue to work again. In this mode, the engine should run for the first 4-5 hours, after which the oil must be replaced. Break-in is over.

The main causes of engine failures

REMEMBER. Engine failures occur mainly from improper use.

The first reason for the breakdown is an unopened fuel cock.

When the engine is not running and the fuel valve is open, the carburetor will be transfused and "flooding" candles. Also gasoline enters the crankcase. And this will lead to excessive pressure during engine operation and squeezing out the seals. Then this mixture of gasoline and oil will enter the combustion chamber and through the exhaust valve into the muffler. Gradually, the muffler will become clogged with oil residues and the engine will lose traction.

CLOSE THE FUEL CRANE AFTER WORK MANDATORY.

The second reason for failure: during transportation or storage, the engine was turned over.

Since the engine is 4-stroke. gasoline is poured into the tank, oil in the crankcase. and they should not mix. After a coup, these components are usually mixed in a carburetor. After that, the engine will need to be disassembled and cleaned.

DO NOT OVERLOAD THE FUELED ENGINE.

And the third reason for the breakdown: improper starting of the motor with a manual starter.

Many users of four-stroke engines think that the more you pull the starter handle, the better the engine will start. This is not true. The starter handle must be pulled until the cams engage and then gently, but with a large amplitude, pull up. And the engine (if it is working of course) will certainly start.

LEARN TO CORRECTLY START THE ENGINE.

Engine Maintenance Table

Instructions for running and operating a 4-stroke engine

Good luck to you.

Call 7 (963) 723-00-43. We will be happy to answer questions related to the operation of air-cooled engines Honda, Briggs&Stratton, Mitsubishi, Subaru-Robin, Lifan, Carver, Loncin, Champion.

Source
Articles , , , ,

Manual. Gasoline Cultivator Br-55, Br-55a, Br-65, Br-65a

Transcript

1 Operation manual for gasoline cultivator BR-55, BR-55A, BR-65, BR-65A

2 CONTENTS Purpose of the cultivator Safety rules for working with the cultivator Main components and controls Inspection before operation Engine oil Air filter Fuel Assembly and installation of mills Starting and stopping the engine Operation of the cultivator Adjusting the height of the handles Coupling the cultivator Maintenance of the cultivator Changing the engine oil Maintenance air filter Cleaning fuel filter Spark plug maintenance Cable adjustment Clutch technology Adjustment of the throttle cable Adjustment of the belt tension Transport and storage of the cultivator Possible malfunctions Technical characteristics Manufacturer’s guarantees

3 Thank you for purchasing our BRAIT brand cultivator! Before starting to operate the cultivator, carefully read the manual. Always keep this manual for future reference. We hope you enjoy working with this equipment. 1. PURPOSE OF THE MOTOCULTIVATOR The motocultivator is intended for operation in areas with a temperate climate. The use of a motor cultivator is most effective at an air temperature of 1C 40C. The service life of the cultivator will increase significantly if you strictly follow all the rules for operation, maintenance and storage specified in this manual and in the “Engine Operating Instructions” installed on the cultivator. Do not rush to use the tractor immediately at full power. REMEMBER that the first 25 hours of operation are a run-in period for the engine and transmission mechanisms. Therefore, it is better to process the same area with a cultivator in several passes, gradually increasing the processing depth. Work on a motor-cultivator does not require special training, however, it should be noted that when working with a motor-block, certain skills are required. In the process of soil cultivation, the space between the cutters and the gear housing can become clogged with stones, wire and other objects. In this case, to avoid damage to the V-belts, it is necessary to turn off the cultivator and remove objects stuck in the cutters. If the soil will often come across small stones and roots, you should reduce the speed of rotation of the knives. To prevent oil from spilling out of the gearbox, engine crankcase and fuel from the fuel tank, the tractor should be mounted on the vehicle in the normal position. 3

4 2. SAFETY RULES WHEN WORKING WITH THE MOTORCULTIVATOR Use the cultivator only for its intended purpose. for the cultivation of land. Before starting work, always check that the cultivator is fully and correctly assembled. Check the correct installation and secure attachment of all tool elements. Learn how to quickly turn off the engine and tiller cutters. Do not leave a working cultivator unattended. Motocultivator is not intended for use by children or people with impaired motor functions, as well as people who are intoxicated, under the influence of drugs. Use ear muffs, goggles or face shield. It is forbidden to work barefoot or in open shoes; wear sturdy shoes to avoid injuries. Do not use a cultivator if wings and protective covers are not installed, and also if the slope of the site exceeds 10 degrees. Fill the tiller with gasoline only in the open air and when the engine is not running. If gasoline spills when filling the tank, be sure to change the starting place, move away at least 3 meters from the spill site. It is forbidden to fill gasoline with the engine running or hot. Do not smoke when refueling and when handling fuel. Gas vapors are highly flammable. Close the gas tank and gas canisters tightly. Start the engine carefully, keep your feet away from rotating knives. Do not use the tool in greenhouses and enclosed spaces to avoid poisoning by the products of the internal combustion engine. When working on slopes, refuel the fuel tank halfway to prevent gas spills. Move perpendicular to the direction of the slope. Always turn off the cultivator when leaving it unattended, as well as at the end of use, before cleaning or transporting. Pre-clean all stones, wire, glass and other objects that could damage the cutters of the cultivator or cause injury from the treatment area. During operation, do not approach a dangerous distance from the rotating milling cutters, keep the distance provided by the handles of the cultivator. Do not change the setting of the engine speed controller or operate at high engine speeds. Check the tiller regularly for malfunctions and damage. If any damage is found, stop using the cultivator immediately and take the device to the nearest service center for diagnosis and repair. All types of repairs, except cleaning and regular maintenance, must be carried out by an authorized service center. Gasoline cultivator is used for cultivating the land in gardens and garden plots. Use for any other purpose is a violation. The manufacturer is not liable in the event of damage resulting from improper use of the cultivator. 4

5 3. BASIC ASSEMBLIES AND CONTROL BODIES Milling rotation drive Oil drain plug Oil filler plug / dipstick Engine fuel tank Fuel tank cover Air filter Muffler Lever with gas cable Lever with forward control cable Lever with forward control cable “ back »Right and left control handles Nuts for fastening handles Side protection Support wheels Working mill 5

6 4. CHECK BEFORE OPERATION 4.1. Engine oil Engine running at low oil levels can cause serious damage and malfunction. џ Unscrew the oil filler cap and carefully wipe the dipstick built into it (see fig. 2). џ Measure the oil level by lowering the dipstick into the oil sump neck. џ If the oil level is low, fill the crankcase with the recommended type of oil to the top of the neck. Use engine oil for a 4-stroke air-cooled engine or equivalent high-purity oil. SAE 10W-30 class oil is recommended for use at any temperature. The use of crude motor oil or two-stroke engine oil will lead to a decrease in engine life Fig.2 1. Oil filling hole 2. High level 3. Low level 6

7 4.2. Air filter An air filter with an oil bath is used on the cultivator. Before starting work, it is necessary (see Fig. 3): џ Unscrew the wing nut, remove the filter cover and disconnect the parts. џ Inspect the air filter to make sure it is not dirty. џ Fill the filter housing to the indicated mark with the same oil used in the engine. џ Assemble the filter. 1. Oil bath with oil level 2. Air filter 3. Filter cover Fig. 3 A dirty filter will obstruct the flow of air into the carburetor. To avoid engine malfunctions, clean the filter regularly. Do this more often if the engine is running in dusty areas Fuel Use motor gasoline with an octane rating of at least 92 (preferably unleaded) (see Figure 4). Never use dirty gasoline or gasoline with oil content. Avoid getting water, dust or dirt in the fuel tank. Refuel in a well-ventilated area with the engine turned off. Damage to the fuel system or engine malfunction due to the use of inappropriate or poor fuel. Fuel tank capacity: 3.6 l. Make sure that the fuel level does not exceed the red limit line (see. Fig. 4) Fig. Red limit line 7

8 5. ASSEMBLY AND INSTALLATION OF MILLERS Consistently install the knives on the flanges of the axis of the milling cutter (see Fig. 5) (install the knives so that the sharpened surfaces of the knives rotate forward during operation) and securely fasten them with bolts, washers and nuts. Incorrect assembly and installation of cutters, in particular incorrect installation of short knives, will lead to breakage of the cultivator. Fig STARTING AND STOPPING THE ENGINE Make sure that the clutch is disengaged and move the shift lever to the neutral position to avoid sudden jerking of the cultivator while starting the engine. The clutch is disengaged by depressing the clutch lever and engaged by releasing the lever. џ Move the fuel cock to the “open” position (ON) and make sure that there is no fuel leak (see fig. 6). Rice Fuel tap 2. Open position (ON) 3. Drain bolt 8

9 џ Close the air damper (set the lever to the “CLOSE” position) (see Fig. 7). Do not close the throttle when the engine is warm or the ambient temperature is high. џ џ џ Slide the engine start switch to the “ON” position. Move the throttle to the full throttle position. Gently pull on the starter grip until you feel resistance, and then pull it sharply toward you. 1. Air damper 2. Closed position (CLOSE) Fig. 7 It is strictly forbidden to release the starter handle, as it may bounce and hit the engine. It is necessary to smoothly return it to its original position in order to avoid damage to the starter (see. Fig. 8). As the engine warms up, gradually move the choke lever to the “OPEN” position (see. Fig. 9). Fig. 8 Fig. Choke lever 2. Open position (OPEN) When turning the engine off, do the following in sequence: џ Turn the throttle to the “Off” position џ Set the engine switch to the “OFF” position џ Move the fuel cock to the “ Turn off ”(OFF) џ Press the engine shutdown button 9

Video: Manual. Gasoline Cultivator Br-55, Br-55a, Br-65, Br-65a


10 7. OPERATION OF THE MOTORCULTIVATOR 7.1. Adjusting the height of the handles In order to adjust the height of the control handles of the cultivator, release the regulator, select the appropriate position (usually at the level of the belt) and tighten the regulator (see Fig. 10). 1. Regulator Fig. Clutch of the cultivator Clutch of the cultivator provides the transmission of engine torque to the gearbox. When the clutch lever is pressed, the clutch is engaged, torque is transmitted to the gearbox. When the clutch lever is released, the gearbox is disconnected from the engine (see. Fig. 11). Fig. Clutch lever 2. Clutch in the “Off” position џ џ џ Gear shifting (see fig. 12): Set the minimum engine speed with the throttle lever. Release the clutch lever. Move the gear lever to the desired position. Fig. 12 If the gear lever does not move to the desired position, depress the clutch lever and slightly move the tiller. 10

11 8. MOTOR CULTIVATOR MAINTENANCE Perform inspections and maintenance in accordance with the table below for maintenance of the cultivator. Engine oil Inner air filter element check check replacement check replacement Fuel filter O-ring cleaning Spark plug cleaning, adjusting Clearance between cleaning rod, valve and pusher adjustment Fuel tank cleaning and fuel filter Clutch cable Throttle cable Belt tension adjustment adjustment adjustment Before starting First a month or after 20 hours of work After every 3 months or 50 hours of work After 6 months or after 100 hours of work After 1 year or after 300 aces Fuel inspection every two years (Replace if necessary) (2) (1) (2) (2) (1) to carry out more frequent inspection and maintenance if the tiller is used in dusty and demanding conditions. (2) Perform these operations in a specialized service. The work is done by the user. After the first 5 hours of operation, it is necessary to change the engine oil. eleven

12 8.1. Changing engine oil It is necessary to drain the oil when the engine has not cooled down, in order to completely and quickly drain the oil. Place a container for collecting oil under the drain neck, unscrew the filler cap and unscrew the drain plug. Drain the oil, then replace the drain plug. Fill in the recommended engine oil, check the level, install the filler cap. The volume of engine oil is 0.6 l (see Fig. 13). Wash hands with soap after contact with used oil. Dispose of engine oil properly, do not pollute the environment. Do not spill used oil on the ground. 1. Oil drain plug. 2. Oil filler cap. 3. Upper level limiter. Fig. Air filter maintenance A dirty air filter may prevent air from entering the carburetor. To prevent malfunctions in the carburetor, regularly clean the air filter. Never use gasoline or thinner to clean the air filter. Ignition hazard exists. Never use a cultivator without an air filter; this can cause a sharp increase in engine wear. An air filter with an oil bath is used on the cultivator. џ During maintenance, it is necessary: ​​џ Unscrew the wing nut, remove the filter cover and disconnect the parts џ Clean the air filter, it should not be dirty џ Fill the filter housing to the indicated mark with the same oil used in the engine џ Collect filter 12

13 8.3. Cleaning the fuel filter Gasoline is a highly flammable and explosive substance. Do not smoke and make sure that there are no flames and sparks near the fuel. Move the fuel cock to the “OFF” position, unscrew the fuel filter nut and O-ring. Rinse the parts in solvent, thoroughly clean them and reinstall them in their original places. Move the fuel cock to the ON position and make sure that there are no leaks (see fig. 14). 1. O-ring 2. Fuel filter nut Fig. Maintenance of the spark plug The muffler is very hot during engine operation. Avoid contact with the muffler. For the engine to work properly, the spark plug must be installed with the correct clearance and there should be no plaque on it. Remove the tip of the high-voltage wire from the candle and twist it with a candle key. Inspect the spark plug. Replace it if the insulator is cracked or broken. Measure the clearance of the plug with a gap gauge. Adjust the distance by bending the side electrode. The clearance should be: 0.70 0.80 mm. Place the washer on the spark plug and tighten it in such a way that it does not twist. Tighten the spark plug with a wrench to squeeze the washer (see fig. 15). When you install a new candle, tighten it another 1/2 turn to press the washer. If you install the candle you used previously, tighten it 1/8 1/4 turn. Note: The spark plug must be properly tightened. An incompletely tightened spark plug can become very hot and damage the engine. Rice

14 8.5. Adjustment of the clutch cable Measure the clutch free play at the end of the lever (see Fig. 16). Free play should be: 3-8 mm. If the clutch cable travel is not appropriate, loosen the lock nut and tighten or unscrew the adjusting bolt if necessary. 1. Lock nut 2. Adjusting bolt Fig. Adjusting the throttle cable Measure the free play of the clutch cable at the end of the lever (see Fig. 17). Free play should be 5-10 mm. If the free play is inappropriate, loosen the lock nut and rotate the adjusting nut if necessary. 1. Throttle lever 2. Adjusting nut 3. Lock nut Fig. Adjusting the belt tension Adjust the belt free play, it should be mm in the area of ​​the tension roller with the clutch engaged (clutch lever must be squeezed out) (see Fig. 18). In order to carry out the adjustment, it is necessary to loosen the four set screws. Move the engine forward or backward to adjust the belt tension (see fig. 19). 1. Installation bolts 2. Engine mounting bolt Fig. 18 Fig. 19 Loosen the mounting bolts on the belt locking mechanism. Adjust the gap between the locking mechanism of the belt and the belt itself, as shown in the figure (with this action, the clutch should be squeezed out) (see Fig. 20). Figure Belt locking mechanism 14

15 9. TRANSPORTING AND WOUNDING THE MOTORCULTIVATOR When transporting, turn off the fuel valve (OFF position) and keep the engine in a horizontal position to avoid fuel leakage. Gas vapors or leaking fuel can ignite. Before storing the engine: 1. Make sure that there is no dampness or dust in the storage room of the cultivator. 2. Drain the fuel. Under certain conditions, gasoline is extremely flammable and explosive. Do not smoke or allow sparks and flames in the work area. џ Turn the fuel valve to the “OFF” position and pull out and release the sump. џ Turn the fuel valve to the “ON” position and pour gasoline from the fuel tank into a suitable container. џ Reinstall the sump and tighten it carefully. 3. Change the engine oil. 4. Remove the candle and pour a tablespoon of clean engine oil into the cylinder. 5. Turn the engine crankshaft several times with a hand starter so that the oil is evenly distributed, then install the spark plug. Pull the starter belt slowly until you feel resistance. Continue pulling the starter cord until the groove on the starter pulley aligns with the hole on the mechanical starter. At this point, the suction valve and exhaust valve are closed, and this will help protect the engine from internal corrosion. Align the mark on the starter pulley with the hole in the mechanical starter housing. 6. Cover the engine to protect it from dust. fifteen

Manual. Gasoline Cultivator Br-55, Br-55a, Br-65, Br-65a

16 10. POSSIBLE MALFUNCTIONS Malfunction Cause Remedy The engine does not start The engine starts, but then stalls 1. The ignition is not turned on 2. The fuel valve is closed 3. There is no gas in the fuel tank 4. Old gas 5. There is no spark 6. The air filter is clogged 7. Low oil level 1. The air damper is closed 2. The fuel cock is closed 3. The air filter is clogged 4. The defective or dirty spark plug 1. Turn on the ignition 2. Open the fuel cock 3. Fill the fuel tank with gasoline 4. Drain the old gasoline, refuel with fresh 5. P clean or replace the spark plug, check the high-voltage wire 6. Clean the air filter 7. Add oil 1. Open the air damper 2. Open the fuel valve 3. Clean the air filter 4. Replace the spark plug 16

17 11. TENIC CHARACTERISTICS Engine Model BR-55 BR-55A BR-65 BR-65A Maximum engine power, kW / hp. 4.0 / 5.5 Single-cylinder, 4-stroke, air cooling 4.8 / 6.5 Engine displacement, cm Max. torque, N m Maximum rotation speed, rpm 12, Piston diameter and stroke, mm 68×45 68×54 Fuel Fuel tank capacity, l Automobile unleaded gasoline, grade A Oil sump capacity, l 0.6 Output shaft diameter, mm Starter Cultivation width, mm / Cultivation depth, mm Number of gears manual / forward, 1 back Net weight, kg

18 12. MANUFACTURER’S WARRANTIES 1. Warranty period for the operation of the cultivator. 12 months from the date of sale. 2. In case of failure of the cultivator during the warranty period of operation due to the fault of the manufacturer, the owner has the right to a free warranty repair upon presentation of the warranty card. For warranty repairs, the owner must send the cultivator with the application of this passport to the warranty workshop in hard transport packaging, ensuring the safety of the product. Satisfaction of consumer claims with defects due to the fault of the manufacturer is carried out in accordance with the law of the Russian Federation “On Protection of Consumer Rights”. With warranty repairs, the warranty period of the cultivator is extended for the duration of the repair and forwarding. 3. The warranty does not apply to motor cultivators with defects that arise as a result of their operation with violations of the passport requirements, including: џ mechanical damage as a result of shock, fall, etc.; џ damage due to exposure to fire, aggressive substances; џ penetration of liquids, foreign objects into the product. 4. The warranty does not cover: џ mechanical damage (cracks, chips, etc.) and damage caused by aggressive agents and high temperatures, foreign objects entering the cultivator, as well as damage resulting from improper storage (corrosion of metal parts) and careless exploitation; џ on wearing parts (toothed belts, rubber seals, oil seals, protective covers, grease, etc.), as well as on replacement accessories and replaceable wearing devices, except for cases of damage to the above parts that occurred as a result of a warranty failure of the cultivator; џ natural wear and tear of the cultivator (full use of the resource, strong internal or external pollution); џ in case of malfunctions caused by force majeure (accident, fire, flood, lightning strike, etc.) џ in case of engine breakdown caused by the use of low-quality fuel. The instructions in this manual do not apply to absolutely all situations that may arise. The operator must be aware that the control of practical operation and the observance of all precautions are his direct responsibility. I have read the terms of the guarantee. I have no complaints about the configuration and appearance. Buyer Central Service Center Phone: 7 (342)

Source
Articles , , , , ,

How to Reel Fishing Line: Reel

Gathering gear for fishing, it is periodically required to change the fishing line on the reel. This is a fairly simple procedure. However, it has a number of nuances. From the correctness of the implementation of such a procedure will depend on whether the thread is flat during casting or if it starts to get confused. If the fisherman does the wrong thing, the thread may break. This causes a lot of difficulties. To avoid such troubles, it is necessary to consider in detail how to wind a fishing line onto a reel. This technology will be discussed in detail in the article.

The importance of proper winding

In order for fishing to be successful, you need to carefully prepare for it. Otherwise, a “terrible thing” can happen. the weather is beautiful, the bite is excellent, and tackle constantly malfunctions and interferes with taking advantage of favorable fishing conditions.

How to Reel Fishing Line: Reel

To prevent this from happening, you need to pre-configure all fishing gear. One of the most important stages of preparation for fishing is the correct winding of fishing line on the spool of the fishing reel. Failure to comply with the basic rules threatens the grief fisherman with entanglement and cliffs of fishing line, and fishing instead of pleasure will become a test for the nervous system.

The casting distance depends on the quality of such work. Proper winding ensures the casting of the bait to a distance that is most consistent with the technical characteristics of the reel.

In addition, high-quality winding prolongs the service life of the fishing line, reducing mechanical friction and reducing the risk of the appearance of a “beard” during casting, because of which it is often necessary to cut the fishing line. Therefore, before starting work, it is necessary to consider some tips of experienced fishermen on how to lay fishing line on the spool. This is a fairly simple procedure that even a beginner can handle.

Winding Profiles

In different models of reels, the turns of fishing line on the spool are applied in different ways. In high-quality products, a cylindrical and conical winding method is used. The laid fishing line in profile forms a straight line. With a cylindrical winding, this line is straight, parallel to the bobbin, with a conical winding, it is oblique.

The straight conical shape narrows to the front side of the spool, the reverse. expands. A straight cone reduces the friction of the fishing line. The reverse type of stacking reduces the likelihood of spontaneous line discharge.

There is a third type of winding. chaotic. Commonly used in cheap Chinese fishing rods. And if such winding can still be tolerated using an ordinary fishing line, then the use of a cord in such a coil should be abandoned. Bad casts, "beard", overlaps and entanglement are provided. This leads to failures during fishing, and can also spoil the mood of every fisherman.

What is backing?

It is usually difficult to determine how much fishing line to wind on a reel. It is believed that a standard bobbin holds a hundred meters fishing line with a diameter of 0.3 mm. However, progress has stepped far forward, and modern fishing lines are becoming thinner, without losing the margin of safety.

How many meters of fishing line to wind on a reel, each angler decides for himself, depending on the fishing conditions. Therefore, it often happens that the selected fishing line is much smaller than the spool can accommodate. The resulting free space needs to be filled with something. Some people use tape or kapron thread for this purpose, but this is not the best option. The glue on the insulating tape, which holds the lower turns of the fishing line, quickly peels off. A kapron thread dries for a very long time when wet.

Therefore, more and more anglers are inclined toward the American method. to reel the fishing line in the lower layer easier and cheaper, and to tie the main, better one to it. This rounds of an inexpensive thread is called backing, in our opinion. reeling. It connects to the main tape using a self-tightening double loop, clinch, or similar knot options.

Determining the amount of winding

In the question of how to wind a fishing line onto a reel, for beginners there is a difficulty in determining the amount of winding. It can only be established experimentally. Experienced fishermen are advised to act in reverse order.

Video: How to Reel Fishing Line: Reel


If there is a second coil of the same kind, you need to wind a fishing line on it first, and then a winding tied to it. At the same time, the basic rule should be remembered: it is only possible to wrap the fishing line on the spinning reel correctly only if the level of its upper layer does not exceed 3 mm from the spool rim. After that, you should rewind the thread to the main shula, already starting with backing, which, as expected, will be at the bottom.

If there is no second same coil, the measurement is made on the main coil, then the fishing line is unwound and rewound on it, already starting from the winding.

Spooling backing

Another important point in the question of how to properly wind the line onto the reel is its connection with the spool. Some fishermen do not fix the line at all, believing that it is long enough and never unwinds completely. This is the wrong approach. Having fixed the winding or fishing line in the spool, you can not be afraid of disruption of large prey or idle scrolling of the fishing line when fishing the fish.

Among the many different binding methods, the following are most common:

  1. A special clinch-like knot. It is very reliable and practically does not stretch.
  2. A self-tightening knot is a special kind of loop with some stretching. However, as a result of the tension of the fishing line, such a knot is tightened to the stop and holds perfectly.

The choice depends on the preferences of the fisherman. Both options are quite reliable. They will provide comfort while fishing.

Manual winding

You must also consider how to wind the line onto the reel manually. If the fisherman has telescopic spinning, it must be decomposed into working condition. This is not necessary for a plug rod; you can work with its lower part.

Attach the coil to the reel seat. There is a hole in the reel on which the fishing line is wound. A rod is inserted into it, for which you can use a pencil, pen, needle, etc. If the fisherman has an assistant, he will hold the axis onto which the bobbin will be untwisted. If there is no assistant, you can hold the rod yourself between the knees.

On sale there are special devices for unwinding fishing line from a bobbin. Their advantage is that they regulate the force when winding the line and make it uniform.

The line is threaded into the rings, from the smallest upper element to the reel. Then the thread is fixed in the spool with the scaffold open. After that, it is lowered into working position. You can start winding the fishing line by rotating the reel.

Hand-wound Precautions

Since the operation is performed with the required tension of the fishing line, you need to hand press it to the rod just above the first ring in order to adjust the tension. In this case, you should know how to wind the line onto the reel without cutting your fingers. You can put a glove on your hand. And you can skip fishing line between the pages of a small book, then it gets additional alignment during the winding process.

Winder

Many "craftsmen" come up with their own ways of winding. For example, you should consider how to accomplish the task with a drill. To do this, you need a nail that almost fits right into the bore of the spool and a rubber circle 7.5 mm thick.

The hardware is inserted into the rubber in the center and placed in the spool. The design is clamped in the drill chuck or screwdriver. The fishing line is fixed in the spool with a knot.

In one hand you need to hold the bobbin with thread for the central hole, in the other. a drill. Winding is done clockwise, adjusting the speed of the cartridge. How to reel a fishing line on a fishing reel correctly with such a device? To do this, you only need to drive the fishing line up and down, making sure that it lies evenly.

Spool storage rules

In order for the fishing line to last longer, you need to properly care for it. Sending tackle for long-term storage, the line should be completely unwound and thoroughly dried, otherwise it will lose elasticity. This is fraught with tears at the most inopportune moment. You can use a dryer to dry. When the fishing line is completely dry, you need to wind it on the spool.

In general, you need to dry the thread after each fishing. Only this should be done not along the entire length, but only on a site slightly larger than the length of the long cast.

Trimmer coil

There are times when the knowledge of the fisherman about the process of laying fishing line on the spool can be useful in a completely different area. For example, the question may arise about how to wind the line onto the trimmer reel. This is a very convenient tool for mowing grass in difficult areas that a conventional lawn mower cannot handle. The cutting element in this tool is the fishing line. Over time, it wears out and breaks. It needs to be changed periodically. Therefore, it is useful to know how the cutting element is replaced.

To do this, you first need to disassemble the trimmer head by pressing on the latch located on the body. The cover rotates clockwise. Take out the bobbin.

Cut about seven meters of fishing line. Its end is inserted into the hole of the bobbin. The required thread diameter is indicated by numbers on the inside. Also on the bobbin, the arrow indicates the direction of winding.

The fishing line is wound on both sides, and its ends 15 cm long are left free. Between the side of the spool and fishing line should be at least six millimeters.

The finished reel with fishing line is inserted into the mowing head. The remaining ends are inserted into the opposite holes of the bobbin and fasten them in the grooves on the head housing. The coil is tightly fixed and closed by the top cover. The tool is fully operational. Need to check his work.

Having considered how to wind a fishing line on a reel, you can easily prepare gear or other tools for use. The thread will not break or get confused. Her move will be smooth. Replacing the fishing line in different reels or even a trimmer will not cause any difficulties.

Source
Articles , ,

Disks For Gas Cutters: What Are, How To Pick And Install?

Knives for Lawn Mower. an irreplaceable thing. It is enough to choose the right one, and you can mow huge areas of grass with their help. Of course, the variety of knives somewhat complicates the task of selecting them. To understand which cutting element is needed, you need to familiarize yourself with the main ones. You should also find out in advance about the correct sharpening and operation of knives.

Species overview

For Lawn Mower preference should be given to special knives. They allow you to mow higher and tougher grass than fishing line. In addition, the knife is suitable even for trimming young bushes.

There are many types of discs that differ in cutting edge, shape and material of which they are made.

Each species has its own characteristics.

For cutting edges

  • with two teeth. for young soft grass, lawns;
  • with three teeth. for young grass, dead wood, weeds;
  • with four teeth. for hard grass and young shoots of trees;
  • with eight teeth mowing grass without strong chopping;
  • with 24 teeth. for hard and dry grass, shrubs, thin trees;
  • with 40 or more teeth. for mowing any grass, bushes, trees;
  • from the 80th and more. for professional motokos.

Blades:

  • with two. for soft and low braids;
  • with three. for mowing weeds;
  • with four or more. for mowing grass on hay.

In shape

The shape distinguishes knives with disk blades and several blades that are at a certain distance from each other. The shape of the blades may also vary. It is worth noting that this does not affect either the speed or the quality of work of the motocosa.

Currently, manufacturers have begun to offer, in addition to traditional shapes, more triangular, rectangular and trapezoidal.

By material

The disc for the brushcutter can be made of metal or plastic. It should be clarified that for electric scythes, plastic blades should be preferred. They are great for the curved bar of this tool, which does not too separate the working area and the legs of the mowing. Plastic knives are able to mow well overgrown dry grass, for example, nettles or burdock trunks.

Metal knives are only suitable for gas trimmers. This is due to the even bar, which removes the disc from the legs to a safe distance. Handles of a special shape also contribute to safety. When hitting a solid object, part of the shock is extinguished by the engine clutch. Knives made of iron are suitable for mowing grass from large areas, weeds, shrubs, young trees.

Manufacturers Overview

There are a lot of manufacturers of disks for motokos. It is worth getting acquainted with the most popular among them. For instance, Bosch brand is known for its two and three-blade knives. A feature of knives of this company is that each of the blades can be replaced separately from the others.

Another company known for its blade knives is Shark. The advantage of the design is that the blades are fixed relative to each other at an angle of 120 degrees. As a result, it is easy to adjust each of the blades, which is convenient for different vegetation. Another feature of knives from this manufacturer is low weight.

Husqvarna is also known for its multi-tooth knives., especially with hay knives. Ideal for thick and dense grass. Of the minuses, it is worth noting the large weight of the disks and the fact that you can’t turn the knife over if one of its sides is sharpened.

Inforce knives do a good job with undergrowth and branches. In practice, the metal from which the cutting elements are made shows itself to be very durable. The only thing is that in some models the victory taps erase very quickly.

Video: Disks For Gas Cutters: What Are, How To Pick And Install?


Disks cope equally well with different types of grass, as well as shrubs and trees.

Rezer wheels perfectly mow grass, weeds, branches. The teeth withstand even cutting down trees 6 and more centimeters thick. However, they have a drawback in the form of winding grass on the shaft.

Patriot produces quality knives. Users note that if you select the right drive for a particular job, it will last a long time and amaze you with its performance. Knives from this manufacturer are very easy to grind on their own.

How to choose?

When choosing a knife for a mower, you should pay attention to many points. For example, discs with metal teeth are most often made in the shape of a circle. The teeth may vary in shape, appearance, size. For small trees, as well as thick grass, it is better to give preference to discs with a large number of teeth.

It is worth noting such an advantage of milling circles for motokos as a quick set of revolutions. However, a high moment of inertia does not affect the drive unit of the unit in the best way. For thick mowing, for tall, as well as for small rough grass and shrubs, it is better to choose circles with 40 or more teeth and perforation. They are able not to grind vegetation, and at the same time it will practically not be wound around a circle. If the number of teeth is more than 60, then you can safely mow grass and trees with a trunk thickness of up to 7 cm.

Disks with a solid blade and without holes have a large mass, so they should be selected for powerful trimmers (more than 40 cm3). At the same time, it is convenient to mow rare grass and dead wood, they are also suitable for mowing with different densities.

Discs with victorious soldering should be selected for mowing plants near obstacles. If you need to mow grass on hay, you should give preference to steel knives with a large number of teeth with smooth sharpening. Solid discs with a number of teeth from 16 to 32 cut plants with thick stems well.

For low-power trimmers, blade discs with a minimum moment of inertia are best suited. The smaller the blades, the stronger the tool will grind the grass. So, disks with two blades are most often used for mowing homogeneous grass. The main advantage of this species is that it throws the cut plants to the side.

When harvesting hay, it is recommended to choose knives with four blades so that the grass is not chopped.

The thickness of the blades is also important when choosing. Discs can be stamped or forged. The former are notable for their low price, but at the same time they can be severely damaged when faced with an obstacle. As for the forged discs, then they do not form chips and cuts in a collision with solid objects.

For electric trimmers, only plastic knives should be selected. Their low weight will not create an extra load on the engine. Soft plastic allows the knives not to break while being on an obstacle, but simply to bend or deform slightly. Use of such cutting elements is recommended for mowing thick soft grass.

How to sharpen and deliver?

With constant use, benzokosa will sooner or later begin to need regular maintenance. One of the important points is the timely sharpening of knives. A metal disk, of course, can work in a dull state, but you can not use it. This leads to reduced performance, overheating of the engine, wear of the gearbox. Sharpening teeth or blades is not difficult at all, but if you wish, you can simply install new knives.

  • First of all, the knife is removed from the device. Sharpening directly on the scythe is not recommended, as it is unsafe.
  • Next, you need to inspect the cutting element for chips, cracks, damage. If they are, then you will need to install a new disk.
  • For sharpening knives, you can use a file, sharpener or grinder. The safest tool is a file that even a beginner can handle. For sharpening, the knife is placed in a vice, and then manually processed at an angle of 30 degrees. This method is considered the highest quality.

When using a grinder, it is important not to overheat the metal, otherwise the disk will quickly become unusable. A grinder with a thin abrasive wheel is suitable for sharpening discs with many teeth.

  • At the end of sharpening, the disk can again be installed on the trimmer and check how effectively the tool works. The sharp parts of the knife cannot be taken to avoid injury.

Over time, the knife wears out and should be changed. Installing a new disc on a trimmer is a snap. This procedure takes no more than 5 minutes if you follow a simple instruction.

  • First you need to remove the protective cover, but on some models it may remain. For example, metal casings cannot be removed from the brushcutter.
  • Next, take the key with six faces (hexagon) and use it to lock the gearbox. The hole for blocking must be sought from the side or from the end.
  • After that, the mowing head must be twisted from the brushcutter.
  • Then a disk will be installed in its place. It is worth paying attention that the inner diameter of the knife should be completely located in the groove reserved for this. The front side of the nozzle should be placed upside down.
  • Now you need to fix the disk with a special washer and screw the fixing nut counterclockwise. Before doing this, it is necessary to lock the gearbox shaft.
  • The last stage is the installation of a protective casing made of plastic.
Source
Articles , , ,

Motoblock Hulk

The manufacturer of Hulk walk-behind tractors is the American company DDE (Dynamic Drive Equipment). The company was founded in the mid-20th century by Daniel Davis. Its original name was Dynamic Equipmen, but the success of the organization was noted by the leading industrialists of America and already in the 90s there was a merger of enterprises and the concern got its current name. The company’s products are high-quality landscape gardening equipment.

Motoblock Hulk

Motorblocks Hulk have proven themselves in the harsh climate of our country. He is not afraid of either low temperatures or dampness. Three modifications with different engines allow the consumer to choose the best option for themselves. Motor-blocks are perfectly aggregated with various attachments, both of their own production, and designed for Neva motor-blocks.

Product Range Overview

The manufacturer has released three modifications of the Hulk brand motoblocks:

  • DDE V 950 II Hulk-1
  • DDE V950 II Hulk-2H
  • DDE V950 II Hulk-3

Let us consider in more detail each modification.

DDE V 950 II Hulk-1

DDE V 950 II Hulk-1 belongs to the middle class technology, its weight is 94.5 kg. The seven-stroke four-stroke petrol unit DDE 270 is installed on the unit. Air protection protects the device from overheating. Starting the engine from a manual starter.

A manual gearbox provides 4 forward and 2 rear speeds. The differential unlock function increases the maneuverability of the unit. The gear-chain reducer is hidden in a reliable aluminum housing. Convenient ergonomic handles are adjustable in two planes, a horn is fixed to the handle. The cultivation depth of cutters can reach 25-30 cm. There is a power take-off shaft that allows you to attach various attachments to the walk-behind tractor. It is recommended to use AI-92 gasoline as fuel. Pneumatic wheels are equipped with a self-cleaning tread that increases the cross-country ability of the walk-behind tractor in viscous soils.

Characteristics

DDE V950 II Hulk-2H

The DDE V950 II Hulk-2H weighs 94.5 kg. and equipped with the powerful four-stroke single-cylinder gasoline engine Honda GX160. Engine performance 5.5 horsepower. Starting reversing from a manual starter.

The transmission is mechanical, multi-stage, provides 4 forward speeds and 2 reverse. Chain drive in a sturdy aluminum case. Unlocking the wheels and self-cleaning tread on pneumatic wheels increase the maneuverability and maneuverability of the unit. Thanks to the power take-off shaft, various functional attachments are attached to the walk-behind tractor. The cultivation depth of cutters is 25-30 cm. Adjustable steering column with horn.

Characteristics

DDE V950 II Hulk-3

Unit weight 96 kg, a gasoline four-stroke power unit DDE with a capacity of 9 horsepower is installed on the walk-behind tractor. Starting the engine from a manual starter. The gear-chain reducer in the aluminum case provides torque transmission to working bodies.

The transmission is mechanical, provides 4 forward and 2 reverse speeds. The power take-off shaft allows you to aggregate various attachments to the walk-behind tractor. The cultivation depth is up to 30 cm. The steering column with horn is adjustable in various planes. Differential unlocking increases machine maneuverability. Powerful protectors with a self-cleaning function on wheels protect the device from sticking and slipping.

Characteristics

Attachments

To expand the functionality of the Hulk brand motoblocks, attachments are used, both of its own manufacturer DDE, and for Neva motoblocks.

DDE manufacturer offers the following equipment

Milling cutters

The manufacturer makes saber-shaped cutters with four knives. A kit for a walk-behind tractor may include 4-6 soil mills. Their main purpose is the cultivation of all types of soils.

The manufacturer produces a revolving and universal plow. Used for the primary plowing of virgin lands, as well as in the preparation of the field for the winter season.

The Hills

Hookers are adjustable, casement, single and double row. Designed for cutting furrows in the beds, ridges of plants, the formation of soil ridges.

Lugs

They consist of a metal rim with welded stiffeners, put on the shaft instead of pneumatic wheels. When moving, they not only move the walk-behind tractor forward, but also perform additional loosening of the soil with ribs.

Indispensable for most field work, used in conjunction with canopies such as hiller, plow, potato planter, digger. It is not intended for movement of the motor-block on a hard asphalt surface.

Potato digger

The nozzle allows you to quickly harvest potatoes.

Potato planters

It consists of a hopper with grabs that immerse the potatoes to the desired depth. A soil ridge immediately forms above the tuber.

Trailer

The folding trailer with belt brakes and mechanical tipping, with a loading capacity of 400 kg, is designed for transporting piece and bulk cargoes.

Video: Motoblock Hulk


Pneumatic wheels

Equipped with powerful self-cleaning agricultural protectors. Used in conjunction with a trailer, mower, snow blower.

Axle extensions

They allow to expand the processing area of ​​the cutters, add lateral stability to the unit.

Couplings

Universal adjustable, thanks to them the walk-behind tractor is aggregated with various attachments.

Braids

Rotary mowers. Used for lawn care, for the preparation of livestock feed.

Pumps

Pumping wastewater, watering plants. the main functions of this canopy.

Snow blowers

The manufacturer offers two varieties: a rotary snow blower and a blade.

The following equipment can be adapted from Neva motor-blocks

Adapter

It consists of a rigid steel frame on wheels and a seat. Turns a walk-behind tractor into a mini tractor.

Weighting

Add weight to the unit, allowing deeper immersion in the soil when processing soil.

If desired, you can purchase caterpillar wheels that will further increase the cross-country ability of the Hulk walk-behind tractor.

User manual

When purchasing any equipment, the first thing you need to make sure that the package includes instructions for use. Next, you need to carefully study the instructions, which disclose the following information about the Hulk walk-behind tractor:

  • The device and assembly of the motor block Hulk.
  • Table with technical specifications.
  • Safety requirements for maintenance and work with walk-behind tractor.
  • Carrying out the first start-up of the unit, running-in.
  • Maintenance.
  • Malfunctions, their causes, solutions.

A table with technical specifications will help evaluate the capabilities of the unit, indicate its exact parameters (dimensions, weight), distinctive features, additional functions and features (power plant power, transmission types, oils used, type of fuel, etc.).

Clearly following the detailed descriptions from the instructions, even a beginner can assemble the unit.

We offer you to read the instructions for motoblocks Hulk concern DDE: Operating Instructions for motoblock Hulk

Recommended oils and lubricants:

  • For Hulk DDE motor-blocks, it is recommended to pour high-quality Oregon oil into the crankcase, SAE 30 is suitable for summer, 5W-30 in winter.
  • For transmission and gearbox, it is recommended to use special transmission lubricants such as SAE 85W90, Lukoil TM-5-18, Reksol TM-5-18.

First start

The first 5-10 hours of operation is a break-in period when all moving parts of the motor are rubbed.

When running in, it is not recommended to use the walk-behind tractor for more than half the power.

After 5 hours of such work, it is necessary to change the oil in the crankcase. Subsequently, such a procedure must be performed every 25 hours of operation.

Maintenance

This section will describe the main stages of maintenance, including:

  • daily care of the walk-behind tractor;
  • inspection and troubleshooting once a month;
  • inspection of the condition of the unit in the service center (recommended once a year);
  • conservation of the walk-behind tractor.

Consider the daily actions that will ensure the long life of the Hulk walk-behind tractor.

Before fieldwork:

  • Check for fuel in the tank and oil in the crankcase, top up if necessary.
  • Check for loose fittings and bolted connections.

At the end of field work (conservation of the unit):

  • To clear the Hulk walk-behind tractor from pollution.
  • Wash with clean water.
  • Dry in a place protected from sunlight.
  • Lubricate fasteners and moving parts with lubricants.
  • Cover and store in a dry place.

Key issues and solutions

We list the most common malfunctions inherent in the Hulk petrol walk-behind tractor.

The engine will not start:

  • there is no gas in the tank. it must be refilled;
  • poor quality gasoline. drain old and pour fresh;
  • the spark plug is burnt or smoky. in the first case, replace, in the second, clean and rinse with gasoline;
  • throttle plug is closed. open it for cold start;
  • the spark plug is disconnected. attach a wire to it;
  • gas leak. wait a few minutes and start the engine again (without refueling);
  • no fuel supply. check and replace hoses, filter, clean carburetor.

The motor runs jerkily:

  • the throttle is half open. close it;
  • dirt or water got into the fuel tank. drain the fuel, fill it with high-quality gasoline;
  • the carburetor is not adjusted. adjust it following the instructions;
  • fuel does not flow. check hoses, carburetor, filter, clean, or replace damaged elements;
  • the spark plug wire is loose or disconnected. fasten it;
  • the fuel filter is out of order. replace it;
  • impeller clogged with dirt. clean it.
  • there is not enough oil in the crankcase. add it;
  • the filter is clogged with dirt. replace it;
  • the fan is clogged with dirt. clean the impeller;
  • carburetor adjustment not set. adjust according to instructions.

Transmission is difficult to switch on:

  • vertical shafts and gears are wedged. clean and lubricate sliding surfaces;
  • keyways clogged with dirt. cleaning.

Transmission Noises:

  • the bearing is worn out. replacement;
  • final drive not adjusted. adjustment according to instructions.

The cutters stopped turning:

  • stones or clods of earth hit the rotors. cleaning will help;
  • stretched or burst belt. replacement will help;
  • the roller and pulley are not adjusted. contact the service center;
  • the pins are lost. replacement.

When starting, the walk-behind tractor moves forward:

  • incorrect position of the clutch lever of the knives. move it to the neutral position.

Video review

Overview of the DDE V950 II walk-behind tractor with auger snow blower

Cultivation Overview Hulk-1 Motoblock

Owner reviews

Yuri, 44 years old:

“I have a Hulk-1, acquired for gardening work two seasons ago. An interesting point. there were no extension cords in the kit, I had to kulibnichat independently. It works, the hiller is better to take a single-row, because for two-row power it is still not enough. With milling cutters it goes confidently, without distortions and slipping. There is a clear drawback. the clutch cable constantly flies out, I try to release the clutch handle as gently as possible, then it releases it, and you correct it every now and then. try to get there. ”

Alexey, 25 years old:

“My Hulk is only a year old, worked the lossless season, though the cutters are a bit soft, I’m thinking about acquiring new ones, and maybe I’ll do the ones I need. Something left of the old Neva. it fits perfectly on the walk-behind tractor. While I’m taking a closer look, I’ll check how it comes out of the winter, how it will behave as a whole. ”

Denis, 29 years old:

“I liked the Hulk walk-behind tractor, completely took over all the field work. The clutch cable really flies. it’s unpleasant, but it does the job. In 2 hours I completely pass my 17 hectare plot, plowed, planted, spud, dug up. everything is on the walk-behind tractor. ”

Source
Articles ,

Correctly Prick Injections to the Child

How to put injections in the buttock to a child or adult

Quite often there are such cases when the doctor prescribes medications that are given in injections. Undoubtedly, in a medical institution an experienced physician will easily enter the necessary dose of medicine for you, and he will not have a question about how to prick an injection in the buttock. But what if the injections are for home use?

Of course, in this case, you can find a familiar nurse and ask her for help, but sometimes it is simply impossible. What to do then? How to put injections in the buttock yourself?

Correctly Prick Injections to the Child

The acquisition of the necessary funds

Sometimes the doctor prescribes antibiotics in the form of injections. In this case, you will have to pre-mix the solution with the powder medicine. Always pay attention to the shelf life of the drug and the method of storage. If it is indicated that the medicine should be in the refrigerator, then this instruction must be strictly observed.

In addition to medicines, you will need syringes. They come in different volumes: from one milliliter to twenty. Choose the one that best suits your injection volume. Consider the number of ampoules. You can not do an intramuscular injection with one tool twice.

Drug preparation

When you have acquired the necessary funds, it is necessary to properly open the ampoules and draw the medicine into the syringe.

Before making an injection in the buttock, open the syringe and put a needle on it. When handling, your hands should be perfectly clean. To do this, wash them with soap or disinfectant.

Open the ampoule by filing a little neck with the special attached file, then break the glass with a sharp movement away from you. Dip the needle of the syringe neatly in a glass container and fill in the solution.

If you need to mix the liquid with the medicine in the form of a powder, then insert the needle into the package with the bulk product through the rubber cover. After that, press the piston and pour water for injection into the flask. Mix the medicine thoroughly and put it back into the instrument.

Before the injection

So, the syringe with the medicine is ready. How to put injections in the buttock?

First, make sure that there are no air bubbles inside the tool. If they are, then they must be deleted. To do this, lightly tap the wall of the syringe with your fingernail. After this manipulation, all the air will gather at the top, and you, slightly pressing on the piston, release it.

How to put injections in the buttock to a child?

If your baby has been prescribed an injection course, then you may well be able to do it yourself. When buying a syringe, give preference to special children’s devices. If your child is very small, then it is quite possible to take an insulin syringe. Its needle is much shorter and thinner compared to a standard tool. However, it must be remembered that such an adaptation is not suitable for an adult. The needle simply does not reach the muscle, and you inject the drug under the skin.

Divide the buttock visually into four parts. If this is your first injection, then you can draw a separating grid in order to get to the right place. For the child it will be a game and fun, and you will be helped.

It is necessary to select the upper right segment of the outer part of the buttock pair (or left. For the left). It is in it that the drug will be introduced. Moisten cotton with an alcohol solution (you can take regular vodka or alcohol-containing lotion). After that, remove the cap from the syringe needle and make sure once again that all air is released. Squeeze the required area for injection with your fingers and squeeze it. With a sharp movement, insert the needle of the syringe and make an intramuscular injection into the buttock.

Some drugs (for example, vitamin preparations) are quite painful when introduced, so you need to press the syringe plunger slowly, gradually introducing the drug.

How to put injections in the buttock for an adult?

Injection to an adult is administered somewhat differently than to a child. You still have to divide the buttock into four parts and select the appropriate segment. After that, wipe the skin with cotton wool and alcohol, and slightly knead the surface of the body.

If, during an injection, the child’s buttock region needed to be squeezed a little, then for an adult, the opposite is true. Slightly stretch the skin to be injected. With a sharp movement of the hand, insert the needle about two-thirds. Gently press the piston and pour in the medicine.

Self-injection

Sometimes situations arise when there is no way to ask someone to give an injection. In this case, you can well carry out this procedure yourself.

Prepare the medicine in a syringe and cotton wool with a disinfectant. Sit on the couch, turning a little to one side. Determine the area necessary for the injection and wipe it with cotton. After that, similarly to the previous methods, inject a syringe perpendicular to the skin. Place your hand in a comfortable position and carefully pour the medicine into the muscle.

How to remove a syringe after an injection?

After the medicine is fully administered, you need to properly remove and dispose of the syringe. Take in one hand the cotton wool that was disinfected before the injection. Gently but surely pull the needle out of your skin and quickly squeeze the wound with cotton. After this, it is necessary to leave the disinfectant tissue on the injection site. This is necessary so that the smallest drops of blood do not stain clothes.

If you give an injection to a baby, then in this case it is better to replace the alcoholized cotton wool with a clean gauze pad or cotton pad. Otherwise, you risk burning your baby.

Video: Correctly Prick Injections to the Child


With an independent injection, you will not be able to simultaneously pull out the needle and put cotton on the injection site. In this case, you must quickly remove the syringe and place the tissue in the desired area. In this case, a few drops of the drug may come out. Nothing wrong with that. Most of the drug is in the muscle.

Recycling

After the injection, close the syringe needle with a cap and place it back in the package. Injection vials should also be placed in a plastic bag. After that, you can throw these items into the bin.

Conclusion

Now you know how to put injections in the buttocks of an adult, a child and himself. Even if an experienced nurse comes to your aid, knowledge of the process of this manipulation will be useful.

If you give an injection to a baby, never fool him or say that it will be completely painless. Say you have a little patience. And in the event that the child steadfastly endured all the trials, praise and encourage him.

Never show your baby that you are afraid. All your movements must be sure. Do not show syringe to child. Try to prepare the injection outside his gaze.

The ability to give injections may never be useful to you, however, knowing the principle of work, you will always be in a winning position.

Be healthy and do not get sick!

Analgin with diphenhydramine appointment and dosage

In acute pain symptoms with a high temperature, which other antipyretic compounds do not knock down, injections can be made with a solution of dipyrone with dipyrone. The effectiveness of medicines in a pair is higher, but they are considered ideal. It is possible to prick a double injection for adults and children. But starting in 2010, pediatricians began to have a negative attitude towards these injections. What purposes and contraindications does an injection of double composition have: analgin and diphenhydramine, our specialists will tell.

Why are drugs effective in combination?

Thanks to a combination of active ingredients, analgindemedrol is effective in several directions at once: analgesic, antipyretic, decongestant, anti-inflammatory and anti-allergic effect.

The absorption of drugs is high, and the effect on the patient’s body is long (up to 6 hours). High injection efficiency makes it possible to use the composition in the most severe cases.

The components of the solution

Analgin is a pyrazoline-based analgesic. Relieves pain cramps of various origins. Pharmacology produces in the form of pills and solution. An injection is made intramuscularly or intravenously. Absorption in injections is faster and more efficient.

Diphenhydramine is an antihistamine with a pronounced anti-inflammatory effect. You can buy it in the form of pills and solution, only by prescription.

Analgin and diphenhydramine with urine are excreted in a day.

In what cases can contraindications be used?

In combination, the solution is used to relieve symptoms:

  • prolonged fever associated with viral or bacterial diseases;
  • pathologies of varying severity with pain syndromes;
  • burns, headaches, muscle pains.

Solution for patients with diseases is contraindicated:

  • asthma and acute forms of an allergic reaction;
  • heart failure;
  • kidney disease
  • neurology of varying severity.

Side effects are associated with improper dosage of the medication and injections performed at home, without the advice of a doctor.

Dosage by age

For pain and high temperature, analgin with diphenhydramine in the complex can be used in the form of pills or injections.

We do not recommend giving an injection to a small child without a doctor, since the baby may have an individual intolerance to the solution.

To calculate the dosage, you can use the table:

It is better to make the solution intramuscularly, since the gastrointestinal tract is not damaged and the components begin to act faster. There are norms of a ready-made composition: For an adult and a child from 10 years old, 1-2 ml / 2 times in 24 hours, a young child, from 3 years old per 10 kg of weight 0.2 ml. But in total no more than 1 ml.

Before the injection, carefully recount the patient’s weight and mg of the solution, otherwise it may cause irreparable harm to the patient. It is better for the child to try to remove the temperature with candles or other drugs before injecting the solution.

Read more on how to make an injection in the buttock, they will tell on the video:

An injection or intravenous injection?

With a large dosage, the drug can be administered intravenously, but only for adult patients. Children are prescribed single injections, intramuscularly. The drug is administered intravenously to adult patients and not more than once a day. The patient is constantly monitored for 24 hours after the dropper.

Intravenous injections begin to act after 5 minutes, intramuscular after 15 minutes.

It is unacceptable to use intravenous and intramuscular injections in combination with drugs: vasoconstrictor or dilating, normalizing pressure, diuretic and choleretic compounds, antihistamines.

If the rules and dosage are not followed, you can harm the body, which will lead to disastrous consequences. Before any injection, consult your healthcare provider.

Injections for young children: we provide assistance correctly

Any purpose of injections means the severity of the situation and the complexity of the disease, however, children have to do injections quite often. There are many reasons for this, one of which is complications after the disease. In hospital care, injecting is a common practice, but it happens that a child can stay at home if it is possible to give him an injection. In addition, injections can relieve an acute condition, including prohibitively high temperature.

    Injections for children: how to do it yourself

    Types of injections

    Injections are done not only in the ass. depending on the purpose and method of administration, intravenous, intramuscular, subcutaneous injections are distinguished. Subcutaneously, drugs are administered when there is no need to achieve an instant effect or, if necessary, for the drug to act for a long time. For example, most childhood vaccinations do this.

    Intravenous administration of the drug is carried out when the instant action of the substance is necessary. This injection requires strict observance of the rules of the conduct, it is technically difficult, therefore, intravenous injection and dropping is the destiny of a medical professional only.

    Another thing is intramuscular injection. It is in this way that the vast majority of injections are carried out. For intramuscular injections, there are several favorable places: thigh, buttocks, shoulder. Buttocks are preferred.

    How to give an intramuscular injection to a child

    When injecting a child independently, it is important to know where to prick, and to strictly follow the sequence of actions during the manipulation. You will need:. ampoule with medicine ;. syringe for injection ;. sterile cotton wool ;. alcohol.

    Choose a syringe with the thinnest needle that will make the injection less painful. Wash your hands thoroughly with soap and wipe them with a sterile cloth. Massage the baby buttocks with massage movements.

    Open the medicine vial with cotton wool moistened with alcohol and print out a disposable injection syringe. Make sure that the piston of the syringe is lowered all the way, i.e. there is no air in it. Put the medicine into the syringe in a slightly larger amount than necessary. Holding the syringe vertically, up with the needle, release the air that has formed inside the syringe and the excess amount of the drug.

    The success of the manipulation largely depends on the behavior of the child, because a frightened, dodgy baby is difficult to keep. Therefore, it is important to prepare the child for an injection, to agree with him

    Lay the child on your lap, stomach down, or on a flat surface. It is important that at the time the needle is inserted, the baby does not wriggle or twitch. It is better if you have an assistant. another adult who will help gently fix the small patient in a stable position.

    Locate the injection site and wipe it with alcohol. An injection should be placed in the outer upper lobe of the buttock, where blood vessels and nerves that cannot be touched do not lie. Gently insert the needle at right angles to the buttock.

    After inserting the syringe, slightly extend its piston. If suddenly the medicine starts to enter the bloodstream, you are in the artery, and the injection site should be changed. If there is no blood, gently administer the medicine. After entering the desired dose, remove the needle from the muscle and treat the injection site with alcohol.

    Source
    Articles , , ,

    How to Reel a Scaffold on a Reed Cutter

    how to wind a new line on a reel on a petrol scythe interskol? | Topic Author: Daria

    Irina Coils are different on trimmers, respectively, differently wound fishing line in them.

    Love according to "you take 8-12-19 m of coil power and stretch this length in half, starting with the loop, try to wind the line into your channel (there should be two of them from the slot, the direction of winding the branches is indicated.
    http://www.fams.ru/pics/m400.jpg

    Gennady trimmer patriot380 how to properly refill a fishing line? one end breaks during operation.

    Tags: How to correctly wind a line on a brushcutter

    How to wind a fishing line on a mowing head of a Lawn Mower (trimmer)

    How to Reel a Scaffold on a Reed Cutter

    How to wind the line onto the spool of the reel? | Topic Author: Homemade

    How to wind the line onto the spool of the reel?
    TIPS OF PROFESSIONALS

    In pursuit of the casting range, anglers use a lot of tricks:
    use longer rods, put the thinnest fishing lines, go to reduce
    the number of bites, increasing the weight of the sinker and forgetting about this at first
    glance at a trivial matter, like the correctness of winding fishing line on a spool of a reel.

    Responsible coil manufacturers usually provide simple circuits of the right
    winding. But who reads these instructions?
    In half the cases, they take a reel of fishing line and simply rewind it to fishing
    reel.
    Nevertheless, it is worthwhile to make a little work and achieve high-quality winding.
    And she, in turn, will provide a casting distance close to maximum
    and prevents self-resetting fishing line loops, often leading to the appearance of a "beard".
    In addition, due to the smaller kink on the rim of the spool, the fishing line will last longer.
    The most rare situations when the capacity of the spool is less than the length of the wound
    fishing line, or when fishing line is wound off a large reel. 500 m and more.
    It is enough to wind so much fishing line so that it does not reach the side
    2-4 mm spools. and no problem.
    If you reel it flush with the sides, then the reel will often make the angler herself
    to correct the correct winding: two or three drops of fishing line loops and the subsequent “beards” will force them to take a knife and remove excess.
    Now fishing lines are becoming thinner and stronger, and the least problems arise
    then when the capacity of the spool is much higher than necessary.
    The best solution would be to make cork or solid inserts
    polystyrene foam, but, alas, many can not do it.
    But still relatively recently, many manufacturers completed coils
    such useful accessories. Therefore, you have to wind up under the main fishing line
    backing. As it is best to use fishing line with a diameter of 0, 25-0, 3 mm.
    Thinner is also suitable, but it will take too much, but from the fishing line
    with a diameter of 0, 4 mm and more it is better to refuse, since “humps” remain from it
    and dips even on reels with good styling.
    If winding is needed under a very thin fishing line, for example for match fishing
    or UL. spinning, then the upper part of it can be done with fishing line 0, 15-0, 2 mm.
    You should not use kapron as a backing, and even more so
    cotton thread: getting wet (and when fishing is inevitable), it takes too long
    dries.

    Video: How to Reel a Scaffold on a Reed Cutter


    How to determine how much fishing line will be needed for winding?

    Very simple. First, the required amount of fishing line is wound on the spool (usually 100 m, but there may be options), and on it. backing, not reaching the edge of the spool rim all the same 2-4 mm.
    Thus, the correct winding will be obtained, but in a mirror version; it can be
    rewind on a spare spool similar in capacity.
    If this is not, then you will have to rewind the fishing line twice to any other reel
    (even Nevskaya will do), and then to the worker.

    Knots for attaching fishing line to the reel It is not necessary to tie a fishing line for reeling, since
    tubercle; the first turn is best glued with a piece of adhesive tape, as, however, is the last.
    By the way, do not forget to tie the main fishing line. there is a special node for this
    (fig. 1).

    I prefer to attach the fishing line to the spool using a long loop (Fig. 2). Firstly, this mount is self-tightening and under load the whole
    an array of fishing line never rotates on a spool, even a metal one.
    And secondly, if necessary, the unit can always be dissolved to replace the fishing line or
    for extra backing.
    Winding backing needs to be rather tight otherwise, when wet, it will become loose and when
    long-range casting the lower turns of the fishing line will fall into the winding.
    And the main fishing line should be wound on a reel with a certain effort
    the same reason.
    Often, fishermen have a question: how to rewind fishing line from a spool to a reel? In my opinion, this can be done as you like: anyway, after the first few
    casting line will twist in this way and as much as the whole
    system. bait, line stiffness, reel roller and spool diameter. The most unpleasant problem, which is typical for most coils with a rocker drive of the spool, is the formation of hollows and “humps” from the fishing line (Fig. 3), which very negatively affects the casting distance. This effect cannot be overcome radically. uneven stroke of the spool
    constructively, but every fisher is capable of improving the winding.
    To do this, apply the method of mirror winding backing (Fig. 4) and the bottom,
    non-working area of ​​the fishing line (usually 30-50 m).
    The method consists in the fact that in the place of the "humps" hollows are made and vice versa.
    Mirror winding has to be done manually; it’s a pretty painstaking job
    from the first yes and from the second or third time to achieve more or less decent
    The result is not always successful.
    However, the game is worth the candle. line quality on most reels
    improves significantly.
    Another point worth paying attention to. storage of fishing line on a reel.
    Usually it looks like this: after the last fishing, the reel is put away for storage,
    and at the beginning of the next season it suddenly turns out that the fishing line began to tear,
    like a rotten thread.
    This is especially characteristic of monofilaments, substantially less. for "braids",
    but any fishing line, if it is not supposed to be changed, can and should be saved
    as good as possible.
    To do this, carefully wrap the entire fishing line from the spool before winter storage.
    (without touching the backing) on ​​the floor, let it dry and rewind it not tightly again.
    In addition, I still wrap spools with fishing line newspaper. she prevents
    accidental damage to the fishing line and, if moisture remains in the winding, dries it.
    Before the start of the season, it is enough to rewind the line with the necessary effort.
    In principle, such an operation will not be superfluous even after each fishing, only in this
    in case you should dry a piece of fishing line a little longer in length than it was
    maximum casting distance.

    Now fishing lines are becoming thinner and stronger, and much more common
    situation when the capacity of the spool is much higher than necessary.

    Andrey Kashtanov Based on materials "Fish with us"
    #Fishing reels

    Source
    Articles , , ,
    1 2 3 … 53