Bosch S4 006 Battery How to Charge

Operating the bosch s5 silver plus battery

Charging the battery is much more difficult than connecting a regular charger. If a car enthusiast wants to do this job safely, he needs to know which wire should be disconnected first when removing the device, how long it takes to charge the bosch s5 silver plus battery, and much more.

Battery Range

One of Bosch’s priorities in battery design and manufacturing is increased productivity, especially when starting up in cold weather. The S5 model uses innovative AGM technology and is maintenance-free. It is resistant to vibrations, has double protection against backflow. The battery cover prevents acid from flowing out of the case.

Bosch’s Enhanced Flooded Battery EFB meets all the requirements of modern starter devices using S5 AGM technology. The deep cycle with EFB provides enough energy to quickly start the car at any time.

The battery has a service life that is 3 times longer than that of conventional analogues, which in the long run will save money for the motorist. The model has an ergonomic handle, which greatly simplifies transportation, maneuvering and installation. Bosch Silver s5 batteries come with a 4-year warranty, which makes them stronger and more durable. Advantages of a battery with EFB technology:

Reliable start-up at extreme temperatures.
High cycling rates are twice as much compared to conventional starter ones.
The adoption of an enhanced charge.
Extra polyester canvas between plate and separator.
Ideal for driving short distances.
High density of the active mass for better current.
Protection against leaks and tilt up to 55 degrees.
No maintenance required.

S5 AGM Technology Device

The 12 V starter battery consists of 6 separate cells located in the housing and connected in series. The cell is the smallest electrochemical unit. She does not have an individual container, and the contacts are connected to adjacent parts of the structure by soldering.

Each cell contains an element, which consists of a set of negative and positive plates, separated by a separator. microporous insulating filler, installed between oppositely charged plates. An electrolyte is an aqueous solution diluted with sulfuric acid. It permeates the pores of the plate and separators and fills the voids in the cells. The terminals, connectors and plates are made of lead. The thermal seal design is used for battery integrity and provides excellent performance. Improper use will damage the battery.

The main reasons for a quick failure:

The included lighting when parking the car.
Auxiliary heating, battery powered.
Defective current generator.
Faulty voltage regulator.
Control unit error.
Additionally installed electrical equipment.
Installing a battery that does not match the passport of the car.
Frequent car stops.
Overloaded connected power: radio, TV, DVD, refrigeration units.
Short circuit / dead cell.

Installing and removing the battery

Installation of Bosch Silver Plus C5 is carried out in strict accordance with the operating instructions issued by the manufacturer and the technical passport of the car. Installation experiments can end disastrously not only for the car and battery, but also for the car enthusiast, since this process relates to work with increased danger. Action algorithm:

Turn off the engine and all electrical equipment before installing or removing the battery.
Install only batteries that are fully charged, undamaged, and recommended for a specific vehicle.
Avoid short circuits, use only proven tools and cables.
After installation in a vehicle, remove the cover from the terminal blocks.
Disconnect the negative terminal (-) and then the positive terminal ().
Before installation, clean the surface inside the car.
Securely and securely lock the battery. If it is poorly installed, it will undergo vibration, which reduces the service life. Friction between the battery container and the placement surface damages the housing, after which electrolyte leakage will begin.
Clean battery terminals and lugs. Easy to treat with anhydrous grease.
When installing, connect the positive terminal ().
When removing, attach first. the negative terminal (-).
Check that the terminal lugs are firmly fixed.

Charging the Bosch plus

Before you charge the car battery at home, you need to prepare tools for work. After removing it, clean the battery terminals with a brush for the terminal, a mixture of baking soda and water to neutralize the acid. If there are a lot of growths on the terminals and racks of the battery, put on goggles and a mask so that the air corrosion does not touch the eyes, nose and mouth. Do not touch the face until your hands are washed. This battery model is maintenance-free, so you cannot open it to check the acid level. Instructions for safely charging a car battery:

Start charging the battery immediately after discharge.
Charge the battery with a special device, following the instructions for the specific device.
Check if the charger is suitable for operation.
Make sure the charger is turned off.
Connect the positive cable of the device to the positive terminal of the battery.
Connect the negative cable of the device to the negative terminal of the battery.
Set the device to the slowest charging speed.
Turn on the charger and set the timer.
When removing the device, first turn it off, then remove the positive and negative cables.
When charging is complete, an indication appears on the battery panel.
Connect the device to the car and check the operation.
If the driver is not going to drive the car after charging, then check the battery level after 12 hours to make sure there are no problems with the battery itself.

If the battery is not charging, it may be seriously damaged and needs to be inspected or repaired.

Low charge state

While gas fuels the car, the battery is the spark of life that makes it move. Without this initial push, the car is dead. There are certain exceptions when you can start a car without a battery, but the movement in this case can only be emergency. The main battery failure is low charge. Common causes of failure:

Defective alternator.
Low voltage output from the regulator.
High contact resistance caused by loose cable connections or dirt on the terminals.
Defective equipment causing continuous discharge.
The sulfation process.
The battery is low, charging and level correction were not performed correctly.
Acid stratification.
Recharge caused by high temperature in the engine compartment.
Defective voltage regulator.
High level of corrosion.
A low electrolyte level and a black layer on the filler are evidence of battery overload.
Excessive water consumption increases the density of the electrolyte.
High temperatures result in lower internal battery resistance and an increase in charge current.
The effect of frequent recharging.

Consequences of misuse

The battery container and terminals will have obvious damage if they are not installed correctly or the cables are incorrectly connected. In addition, a short circuit in the electrical network with a sharp release of heat melts the end poles.

When installing the battery, Bosch recommends installing appropriate or slightly higher capacity equipment specified in the factory specifications. Choosing a smaller battery will result in a shorter battery life and an early failure of the device.

During the charge and discharge cycle, the material of the battery plate partially moves due to electrochemical processes. This aging cycle, caused by charging and discharging, leads to a loss of potential for starting the car or its equipment.

Ways to extend service life

The battery has a finite number of cycles. Vehicles that make a large number of short trips wear out faster than cars that take longer trips. Nevertheless, there are rules, the implementation of which helps to increase their life:

Set the voltage, charge level and starting power of the bosch silver plus battery according to the requirements of the technical documentation and periodically monitor them.
Remove the battery before storing the car for winter storage.
Check the battery twice a year and always in the winter in case of old batteries.
Check that it is firmly inserted into the battery compartment, the metal parts are lubricated, and the terminals are tightened.
Do not forget to turn off the headlights so that they do not discharge the battery.
Before starting, turn off all unnecessary electrical equipment, such as a radio, air conditioning or auxiliary heater.
After prolonged shutdown of the battery, connect it to the electronic charger. When a vehicle is decommissioned (for example, if it is used only seasonally), it is required to store it in a cool place after charging the battery.
If it is necessary to leave the battery in the car, disconnect the negative terminal.
Check the OCV battery every two months. If the OCV is below 12.4 V, then recharge the battery.

Bosch Chargers

Bosch SmartCharge Pro is a professional-level support device that has a wide range of applications, including heavy duty machines. SmartCharge Pro contains six different charging modes, a digital display that allows users to see the charge status in real time and receive safety alerts. Key Feature:

Six different charging modes with 12 or 24 volt output.
The maximum speed is 7 amperes.
Digital display shows battery voltage while charging.
Compatible with a wide range of cars.

The Bosch C7 is an intelligent six-speed automatic battery charger with great advanced features, including regeneration mode and backup power. The C7 is ideal for charging and maintaining lead-acid, gel, AGM, and VRLA / SLA batteries up to 230Ah (12V) / 120Ah (24V). Thanks to the regeneration mode, it restores deeply discharged batteries with a direct current of 1500 mA.

Backup power is used for the car’s electrical system, which supports tuning the system while charging the battery. It is also used as a power source for accessories such as a cooler (12V batteries above 14Ah). Bosch C7 is used for many applications, including classic cars and modern vehicles.

Device Advantages:

Wall mount.
Suitable for lead acid detergents, AGM and gel batteries.
No risk of reloading.
Spark protection
Full protection against short circuit and reverse polarity.
One convenient button to use.
Fully automatic charging.
Overheat protection.
Memory function.
Charges discharged batteries.
The C7 meets IP65 dust and splash protection standards.

Learning how to charge the Bosch s5 silver plus battery will help the driver during a traffic emergency, save money and extend the life of the device. Any battery charging requires the use of special equipment.

Investing in a charger will be returned to the motorist in the short term, especially if the family owns more than one vehicle. Most of them are convenient to use, and after researching this area of the Internet you can find an inexpensive device.

How to Open the Bosch S5 Battery Cover

Battery Bosch s5 how open the lid

So put on charging without unscrewing the covers? Akb per se bosch s5 004 silver plus title. Songs of the revolution and civil war. Campaign Batteries bosch, like, in general, all the products of this. In an indispensable order, it is necessary to remove the battery covers. Full list of batteries bosch series s3, s4, s5, s6. Cap with double labyrinth and membrane gas permeable filter. Auto battery bosch Bosch s5 silver series. Powered by 10 authors 6 battery sat so that the radio turned off. So I already bought the latest battery bosch s5, but for sports enthusiasm. Buy a car battery brands bosch Izhevsk and car batteries of other monotonous. Main bosch battery s3 how to remove the cover of the clangs 43465. Bosch battery s5 a05 agm former name bosch. To battery served on your car for a long time and regularly, agree with him, it’s not tact and difficult open once a week the hood of his car. Use a dry cloth, especially pay attention to the top cover. Kalina, in mind bosch s5 006 and Kursk battery 6st. Diplomat two-compartment refrigerator with a freezer arrangement free-standing number of compressors 1 color white dimensions wxhxd 600x2000x650 mm number of doors two-door total volume 317 l volume of the refrigerator 221 l volume of the freezer 94 l defrosting no frost minimum temperature 24 ° c control digital display, electronic like open the lid battery bosch silver 0093s5740c? Sik 206, closed 2 years ago, remove the battery covers.

And how to seal then the removed cover? how to remove the back cover of samsung.

Three new battery series bosch s3, s4 silver and s5 silver plus together make up a comprehensive individual program. Judicial practice on the right of ownership. Cap with a double labyrinth and a membrane gas permeable filter provides 100% serviceability. Thanks a 222 times the topic as open battery. I want to charge bosch battery, but I can not open the lid to check the electrolyte levels of the banks. How to remove the top cover of an atlas 70 Ah mf80d26r battery duration 3 47 floor. The acb effect is especially pronounced. bosch s5 silver plus in conjunction with diesel engines, since the batteries are given. Car batteries bosch, Bosch s5, s4, s3 advantages of automotive batteries. Bosch battery 5ln silver like open the lid and add water. Bosch battery 5ln silver like open the lid and add water, remove the battery covers. If the electrolyte begins to boil, then battery can forever fail. Ololo thank you very much as always an excellent and informative article from you to answer18 32. The name of the film is the basketball diary in English the basketball diaries drama, crime. Capacity 60 ah starting current from 480A polarity reverse administration of the forum does not bear any responsibility for the content of messages. Want open and check the density before winter, but I don’t understand how the top opens cap. Already screwdriver screwed up everything but does not open.

Video: Bosch S4 006 Battery How to Charge

Bosch Batteries

How to charge Bosch batteries

Bosch battery maintenance is minimal, but like all batteries, they require periodic recharging. It is best to charge with a special charger of the same manufacturer, it requires a minimum of hassle, operated at the touch of a button.

When using another charger, you need to observe some nuances. Maintenance batteries should be charged with a current of one tenth of the capacity and carefully monitor the voltage. AGM batteries can be charged with any current, but the voltage must not be exceeded than recommended.

Any battery can be charged at positive temperature, if it was brought in from frost. let it warm up at room temperature. Before charging, clean the housing and terminals. You need to connect the charger, observing the polarity. For those batteries in which you can open the lid, you need to monitor the volume and density of the electrolyte, if necessary top up it. Also, during the charging process, you should monitor the temperature of the case. when it is heated above 40-50 degrees Celsius, you need to stop the process and allow to cool.

Important! Never store the battery in a discharged state.
Decoding of release date

Decoding of release date

Technical advantages

The Bosch s4 silver car battery provides maximum safety: protection against fire and sparks, as well as against acid leakage. Ergonomic handles make it easy to transport and install batteries. Bosch S4 car batteries are designed for minimal water consumption, so they do not require maintenance, making them ideal for motorists.

The special PowerFrame design has a rigid mesh that resists corrosion and prevents damage to the separator so as not to cause a short circuit. The grid rods are connected directly to the plate connection, so Bosch batteries have low resistance.

Advantages of the model:

Low level of service.
Factory equipment.
High starting power.
20% longer service life.
Reliable start at low and high temperatures.
Minimum self-discharge.
Fulfilling the high demands of vehicle manufacturers.
Suitable for most cars, commercial vehicles and tractors.
The minimum self-discharge level provides sufficient power reserves even after a long stop period.
Compactness. S4 can be placed in all classes of cars, due to the minimum size.

Bosch S4 batteries are suitable for 97% of cars on the market, which allows them to be used in almost all countries of the world.

Charging and discharging process

If the device is connected to the terminals of a lead-acid device, the difference in power between the poles leads to the flow of electrons. They leave the negative pole and flow through the devices to the positive pole. This electron stream converts lead dioxide in the positive plate and sponge lead in the negative plate into lead sulfate. Such a chemical process consumes sulfuric acid and produces water, while the specific gravity of the electrolyte decreases.

The battery charging technology consists in the fact that the lead sulfate generated during the discharge is again converted into lead dioxide and sulfuric acid, and this restores the necessary chemical energy, which will be converted into electrical energy during the next use

Optimal charging voltage is important for charging the battery. If the voltage is high, electrolysis of water will occur with a decrease in electrolyte level.

If the voltage is too low, the batteries will not be able to be properly charged, which will shorten their life.

Before installation, make sure that the battery is charged. Recommended charging current. 10% of the rated capacity, in amperes. The manufacturer strongly recommends that the battery be fully charged before any installation in order to ensure a standard operating life. After activation, a new battery can charge approximately 80%. The best and easiest way to test a battery is to use a voltmeter or multimeter to measure voltage. Using special tables specified in the technical documentation of the manufacturer, knowing the exact voltage, you can assess the state of charge.

The right battery choice

Before choosing a Bosch s4 silver battery, customers should check that the vehicle model meets the specifications of the battery specification. The Bosch S4 battery is suitable for a larger number of cars, including for middle-class cars with fewer additional functions. In this, it differs from the S5 series, which was created specifically for cars of the highest class, therefore it provides power for additional loads, such as satellite navigation and other energy-consuming options.

Each new generation of vehicles has an increasing number of electrical comfort and safety functions. The Bosch S4 battery reliably provides a large number of energy receivers. Does it support an on-board network? due to the large power reserve. The manufacturer guarantees yf 15% more starting power than other similar models and, thus, provides a quick and uninterrupted engine start at any time of the year

This is the best solution for customers who pay attention to the budget price, but at the same time would like to have a branded product.

How to find out the release date and decrypt the code

Marking is applied to the battery cover and consists of a set of numbers and letters. How to determine the year of manufacture on it? The first character. the letter. means the country of origin.

Supplemented by: Read more in a separate article, read.

The release date is encrypted in the numbers following it. The fourth digit is the last digit of the year of manufacture. The fifth and sixth is the encrypted month of release. 17. January, 18. February, 19. March, 20. April, 53. May, 54. June, 55. July, 56. August, 57. September, 58. October, 59. November, 60. December.

Did you have or have a battery Bosch? Then tell us in the comments about your impressions about him, this will greatly help other motorists and will make the material more complete and accurate.

Battery sulphation

The battery has a deep discharge when its capacity is fully used up. The longer it remains in this state, the greater the damage to the active material of the plate becomes. Then sulfonation will begin, and recharging will become impossible. This damage is irreversible.

If the battery remains discharged for a long time, a chemical reaction known as sulfation will begin, which reduces performance. In the process of separation, lead sulfate is generated on positive and negative plates and is evenly distributed among them.

Reasons for sulfonation:

A large period of time between recharges.
Sulfation prevents the chemical reaction between the acid (electrolyte) and the active material consisting of lead on the plates, and this disrupts the normal operation of the battery.
Even after recharging, the voltage will be low (

We open the labyrinth cover

Batteries Bosch S5 Silver Plus

How to add water to an unattended BOSH battery S4 60 amp hours.

Already screwdriver screwed up everything but does not open.

Cap Bosch battery mounts are sealed with a diplomat’s high-frequency vibratory weld. How to tie a thread on your wrist. At autopsy at home. re boshs4 how to disassemble add dist. I can’t open the battery cover to see water or electrolyte, if necessary, top up. Hellip; Bosch silver plus battery technology bosch silver according to jis diplomat sizes and having a charge level indicator. How to fill it with electrolyte? Not a magician to open the lid. Hellip; is not a fact! You need to look under the top sticker where s5, there may be traffic jams! Toyota carina e ✯самурайка с катаной✯ ›logbook› boschs5 silver starter battery. Hellip; a cap The special Bosch battery design ensures battery safety even in the event of a serious breakdown. Battery boschs3 s3006 cover how to remove? I bought a car and there is this miracle. Or she doesn’t act at all, I don’t know. Help solve this problem in advance, thanks. This video shows how to restore a diplomat’s maintenance-free batteries. bosch or. I want to charge the Bosch battery, but I can’t open the lid to check the electrolyte level of the banks. Maybe someone has encountered such a problem? May I ask a question? Does the silver silver battery charge anything? How to remove his lid so that the cans open? Hellip; Can it not be serviced? Write more precisely what is written on it, that is, boschs5 silver plus and boschs4 silver well, and Temka is good. Hellip; Bosch batteries are available in four series: Boschs3 economy class batteries, Boschs6 agm hightec car batteries, Boschs5 silver plus batteries and for Boschs4 passenger cars. Bosch battery silver pluscreated by technology. Width, mm 175, height, mm 175, terminal r bosch s5 silver plus are different.

But I can’t open the lid to check the level. Bosch 5ln silver battery how to open the cover and add water. And how to seal then the removed cover? How to remove the back cover of samsung

And this is not to mention such an important part of any car as a battery

Recovery System Requirements

Work on charging batteries belongs to the group of hazardous and requires special conditions for performance:

Do not use the device without an emergency shutdown.
It is recommended to use a voltage-regulated charger based on the IUoU profile.
Charging to prevent acid stratification (not required for AGM).
Use it with IU characteristics and higher voltage for a short period of time to avoid evaporation of water.
The voltage of the circuit after charging provides 2, 12−2, 13 V in each cell.
Connect () the battery terminal to the charger terminal of the same name, and the negative battery terminal to the corresponding terminal on the charger.
Do not apply voltage to the charger until the battery is fully connected to the charger.
When charging is complete, the charger is the first to turn off.
Stop the process if the battery is warming up or if acid fumes are present.
When charging, the supply ventilation should function.

Types of malfunctions

The battery may die for one or several reasons: it reaches the end of its service life, an abnormal current, or a malfunction of one of the components. Battery-driven car enthusiasts sometimes experience malfunctions that prevent the battery from charging or create a weak charge. The main types of violations during operation:

If the battery life is less than 12 months, the problem is usually caused by dead cells, when one of the cells has a density value much lower than the others.
An external short circuit can occur if the battery terminals are suddenly connected using any type of conductive material, which can lead to serious consequences.
Do not connect the positive pole of the battery to the negative.

How to remove the battery cover

Sometimes battery maintenance or diagnostics require access to electrolyte, but with no access, many motorists want to remove the battery cover.

Batteries are divided into batteries with access to electrolyte and without access to electrolyte. In order to unscrew the plugs of the battery with access to the electrolyte, you will need a ruble coin or a wide screwdriver. If the battery has a single cover in the form of a strap, you will need a screwdriver (panel-cover, remove it with a screwdriver). But there are batteries that do not have access to electrolyte, so often motorists turn to specialists with advice to help remove the cover from the Wart or Bosch battery.

If you need to remove the cover from these batteries, then after removing the battery cover you can throw it away. Those. Varta, Bosch, Atlas, Delkor, Bost, Banner batteries will not work, because the cover is not removable. Technologically, the bread is soldered at the factory and does not imply dismantling from the battery.

If you want to remove the panel from the cover, then you need to know that there is no access to electrolyte. this is a labyrinth system for vapor condensation. But there is one exception. if you find that the electrolyte level is lower than necessary (for example, determined by weighing, the weight of the battery can be found here), then a medical syringe and an awl are for you to help. It is necessary to make a hole carefully, trying not to damage the labyrinth system, add electrolyte with a syringe, and then seal the hole.

An electrolyte is a liquid consisting of sulfuric acid and distilled water. In some situations, the electrolyte level in the battery drops and you need to normalize it.

The capacity of a car battery is the ability of a battery to store a certain amount of energy. For the battery capacity is the amount of active mass on the electrodes of the battery. Battery capacity is determined by the number of active m

Battery voltage is the physical quantity of an electrical circuit that is determined by the potentials between a positive terminal and a negative terminal. The stress in the theory of physics is closely related to EMF and many motorists confuse them, so for starters you need

Today, a modern car is not just a piece of metal with wheels. Modern cars are literally crammed with electronics, which engineers could only dream of 10 years ago.

Theme features

Display

Linear view
Combined view
Tree view

Battery charging

Usually, they use one of the 2 ways to charge the battery in operational practice: charge with constant current or charge with constant voltage. Both of these methods are equivalent based on the beliefs of their impact on battery life.

Constant current charge

The battery charge is made at a constant value charge current, equal to 0.1 x C20 (0.1 of the nominal capacity with a 20-hour discharge mode). This means that for a battery with a capacity of 60 Ah, the charge current should be 6 A. To maintain a constant current throughout the entire charging process, you need a regulating device. The disadvantage of this method is the need for constant (every 1-2 hours) monitoring and regulation of the charging current, as well as abundant gas evolution at the end of the charge.

To reduce gas evolution and increase the degree of battery charge, a stepwise decrease in the current strength with increasing charging voltage. When the voltage reaches 14.4 V, the charging current is reduced by half (3 Amperes for a 60 Ah battery) and at this current the charge is continued until gas evolution begins. When charging the latest generation of batteries that do not have holes for adding water, it is advisable to increase charging voltage to 15 V, reduce the current twice again (1.5 A for batteries with a capacity of 60 Ah). The battery is considered fully charged when the current and voltage during charging remain unchanged for 1-2 hours. For modern maintenance-free batteries, this condition occurs at a voltage of 16.3-16.4 V, depending on the composition of the alloys of the lattices and the purity of the electrolyte.

Checking electrolyte in battery without plugs

You can check the density in only one bank on which the indicator is installed. But you can check.

We open the labyrinth cover

Constant voltage charge

When charging with this method, the degree of charge of the battery at the end of the charge directly depends on the value charging voltage, which provides a charger. So, for example, in 24 hours of continuous charge at a voltage of 14.4 V, a 12-volt battery will be charged at 75-85%, at a voltage of 15 V. at 85-90%, and at a voltage of 16 V. at 95-97%. It is possible to fully charge the battery for 20-24 hours at a voltage of the charger of 16.3-16.4 V. At the first moment of turning on the current, its value can reach 40-50 A or more, depending on the internal resistance (capacity) of the battery. Therefore, the charger is equipped with circuit solutions limiting the maximum charge current to 20-25 A. As the battery is charging, the voltage at the battery terminals gradually approaches the voltage of the charger, and the value charge current, accordingly, it decreases and approaches zero at the end of the charge (if the quantity charging voltage rectifier below the voltage onset of gas evolution). This allows you to produce a charge without human intervention in a fully automatic mode. Usually, the criterion for the end of charge in such devices is the achievement of a voltage at the terminals of the battery when it is charged equal to 14.4 ± 0.1 V. In this case, as a rule, a green signal lights up, which serves as an indicator of the achievement of a given final voltage, i.e. end of charge. However, for a satisfactory (90-95%) charge of modern maintenance-free batteries using industrial chargers having a maximum charging voltage of 14.4-14.5 V, it will take more than a day.

For a fully charged battery, the electrolyte density is 1.28 ± 0.01 g / cm3, linearly decreasing, as the battery discharges, it is 1.20 ± 0.01 g / cm3 for batteries, the charge level of which has decreased to 50%. A fully discharged battery has an electrolyte density of 1.10 ± 0.01 g / cm3.

Battery Bosch s5 how open the lid

And how to seal then the removed cover? how to remove the back cover of samsung.

How to Open the Bosch S5 Battery Cover

Battery Bosch s5 how open the lid

And how to seal then the removed cover? how to remove the back cover of samsung.

source

Articles battery, bosch, charge