Care for the chainsaw of Stihl for the winter. Gasoline lawn mower

Conservation of the chainsaw for the winter period

Chainsaw is an indispensable tool for sawing wood. According to the principle of operation due to the fact that when cutting the cutting element is a chain, it is also called a chain saw.

The choice of famous and reliable manufacturers and the proper operation of the chainsaw is not all criteria that affect the long.term operation of the tool. It is important to comply with the rules for the storage and conservation of equipment for the winter period.

Conservation rules for long breaks in work

One of the important factors that affect the uninterrupted operation of the chainsaw for a long period of operation is proper storage.

Most manufacturers recommend storing the tool in a dry and not dusty place. In addition, there are a number of mandatory procedures, during which your chainsaws will ensure uninterrupted operation after long.term storage. The list of preparatory work is as follows:

• – Devastation of the fuel tank. It is necessary to completely drain all the contents of the fuel tank. Attention! This procedure should take place only in a well.ventilated room and far from the fire. Give the chainsaw to work a little after the devastation of the fuel tank, you need to develop the remaining fuel in the fuel system and carburetor. This will help to avoid the likelihood of sticking membranes in the carburetor during storage.

• – Washing components. It is recommended to wash all the elements of the case with warm water with a brush. Pure details are a great opportunity to do a visual technical inspection and in the event of defects, bent, distortions, breaks and cracks, make current repairs or replacement.

• – Dismantling the chainsaw. A coarse bonds will allow you to clean all the cutting parts from the remnants of wood and sawdust. As a rule, a saw chain and a guide tire are removed. To preserve the performance and mobility of all elements, it is necessary to carefully treat all parts of protective anti.corrosion oil grease.

• – Model conservation. It is necessary to unscrew the spark plug and bring the piston to the extreme upper point by the starter, pour slightly motor oil into the candle hole (approximately 20g.) and slowly turn the crankshaft by the starter. This procedure will allow lubricate the entire piston group. Scroll the crankshaft several times for more thorough lubrication. Install the spark plug back, (it is not necessary to tighten). In addition, it is necessary to make those. Inspection of the air filter, inspect the clutch condition and, if necessary, carry out accurate adjustment and tuning of the carburetor of the chainsaw.

• – Dry storage. Even after thorough processing of mobile mechanisms, storage of an open.air tool and under the influence of atmospheric precipitation is not recommended. For storage of a chainsaw, it is necessary to provide a dry and well.ventilated place in the room. It is advisable to wrap the chainsaw engine in a rag or bag, this will allow you to protect the engine from unwanted moisture in the formation of the temperature and the formation of condensate.

• – Sun protection. Avoid direct sunlight on the mechanisms of the chainsaw, especially the engine elements. Nozzles and some rubber elements can lose elasticity, become fragile and burst. This may not appear immediately, but in the process of work, and at the most inopportune moment.

• – Storage in dustproof packaging. Take care of minimizing dust entering the engine elements, short circuits of electrical wiring contacts may occur, or generally blocking the conductivity of contacts. Many manufacturers of equipment produce special dust and moisture-proof covers that provide reliable protection of tools.

• – Reliable storage. The chainsaw must be stored in an inaccessible place for children. This is not a toy! You can get hurt with sharp parts of the cutting chain and tire. It is best to store a chainsaw in a closet with a lock.

The chainsaws of various manufacturers can differ among themselves both parameters and technical characteristics. The main differences in chainsaws can be:

• – Engine brand.
• – Type of oil pump.
• – Crankcase crankcase.
• – Chain brake.
• – The method of maintenance of the circuit.
• – The shape of the case.
• – Ergonomics of the handle.

But, despite all the differences, the above algorithm of conservation actions will help save the tool in working condition for a long period. The procedure and the sequence of work may differ slightly from the recommended by the manufacturer. Therefore, carefully study the instructions for the operation of the product and adhere to clear recommendations of the manufacturer.

How to translate the Stihl chainsaw to winter mode?

STIHL tools are reliable and durable, they are designed for long.term operation and can work under extreme conditions: at high loads and in winter at low temperatures. If you purchase such models from official dealers, they will cost inexpensively. you can buy a chainsaw in Kostroma to the cottage or for professional use. A trimmer for grass will last a long time if you follow the operating rules, guided by seasonal conditions.

At the surrounding temperature, the engine is launched and the degree of wear of its parts depends. If in the frost you will immediately start working with an unfinished tool, it will not last a long time. You need to convert the chainsaw to winter mode.

Transfer of a chainsaw into winter mode

The transition to winter operation is carried out at ambient temperature below 10 degrees. In such conditions, the carburetor begins to freeze, which is why the fuel-air mixture is poorly prepared, the launch is difficult, and interruptions in the engine can appear.

To transfer the chainsaw to the winter mode, follow the following sequence of actions:

• Press the lock of the gas lever and turn the combined lever to the position of a closed air damper;
• Turn the button above the rear handle at right angles;
• Remove the carburetor lid, pulling it up;
• Remove the valve from the spark plug and turn it 180 degrees and set it in a new position;
• Put the lid back and fix it with a button.

Now the carburetor will warm up with warm air from the cylinder, the tool will be possible even at negative temperatures. This regime helps to prepare high-quality fuel-air mixture, which excludes the filling of candles and interruptions in the engine operation. The transition to the summer mode is carried out in the reverse order. At temperatures above 20 degrees, it is forbidden to work with an open damper, this can lead to overheating.

Preparation for storage and conservation of a chain saw tool

If the chainsaw is planned to be stored for a long time, it must be disassembled, cleaned, washed and dry for. But preliminary from saw technique you need to drain all gasoline. To empty the fuel, you should start a chainsaw with an empty fuel tank. After a few seconds, the saw motor itself will stall in itself.

Additionally, the engine lubrication system should also be lowered. During the winter period, the existing oil will still deteriorate. The fact is that any motor lubricant contains additives (friction modifiers, antioxidants, etc.). With a long stagnation, especially if low temperature, the additives are deactivated and precipitated.

The chainsaw is versed in the following order:

• Disconnect the tire and remove the chain. The tire and chain should be cleaned from blockages. You can even rinse them in kerosene and dry well. If the chain managed to swell after the last sharpening, then it is advisable to correct the tip of the chain. Of course, you can leave this work in the spring.

The chain tire must be covered with a thin layer of preservative. Suitable movil or cannon fowdered. That is, you need to drop a little preservative on a rag and grind the spare parts for them. The tire with a chain should be stored in oiled paper, best of the parchment. But just ordinary rags are suitable.

• We extract filter elements from the chainsaw. It is necessary to extract coarse cleaning filters from the fuel tank and the neck of the lubricant system. Cricking filters are simply washed and dried. If a filter of fine fuel is provided, then it is best to simply replace it with a completely new analogue in the spring.

Special attention should be paid to the air filter. The airfall filtration element must be disconnected and cleaned well. If the filter has already worked for 2-3 seasons, then it makes sense to just put in the spring a new element of air filtration.

• We unscrew the spark plug and clean the candle head, especially the electrode, from the carbon. The user must track the service life of the candle. Subject to intensive operation of the chain saw, the candle usually works out 2-3 seasons. If the chainsaws are rarely used, then the candles are enough for an average of 4-5 seasons.

If good performance is expected from the chainsaw, then the spark plug should be changed every 2 years!

• Add 5 (ml) of motor oil to the candle well and scroll the crankshaft 2-3 revolutions. You can scroll the crankshaft by the asterisk of the chain. This technique will allow motor lubrication to create a thin protective layer in the cylinder.

As mentioned above, the lubricant has the ability to drive and dry with stagnation. It is for this reason that the user needs to manually scroll the cranks of the chain saw with a frequency of 1 time per month. If the user obviously knows that he will not have time or opportunity to regularly develop a power unit, then it is better not to fill the oil in the cylinder.

Do not forget to screw back the pre.cleaned spark plug!

• Clean and lubricate the chain tensioner.
• We pack all the disconnected parts and the power unit itself. To increase safety, it is better to store a saw tool in a strong cardboard box. You do not need to make a container container, since moisture can accumulate without air exchange in the box.

How to work with a chainsaw in the winter period

The need for a chainsaw may arise in winter. In this case, the user needs to know how to make the work of a saw chain tool as reliable and safe as possible.

The main catch during the operation of the chainsaw in winter lies in the low ambient temperature. In the cold, gasoline becomes less volatile, which affects the work of the carburetor. To start a chainsaw and warm up the engine to the conditioning temperature, very often you need to use a forced fuel suction.

Who does not know, with a manual fuel suction, candles are filled with gasoline. In this case, the candles quickly become overgrown with soot, they need to be cleaned almost after each use.

It is necessary to be prepared to the fact that the lubricant system will not work 100% effectively. Oil for chain saws thickens in the cold. To prevent an increase in viscosity, a small portion of gasoline should be added to the oil.

After the entire front of the work, the chainsaw should be preserved for storage according to the above scheme.

Do I need to preserve an electric chain saw in winter

Chainsaws differ from electric chain saws only by the type of drive system. The electric saws were a little more lucky, because they do not use liquid fuel, they have no spark plugs, no filters, no carburetor. But electric saws need conservation for the winter. Of course, for electric saws, a simplified preparation scheme for storage is provided.

You just need to disconnect the tire with a chain, beveled from and grease with a preservative. Everything is as in the case of gasoline analogues. If the chain managed to swell, we correct the sharp edges on the teeth.

Additionally, the chain tensioner should be cleaned and lubricated. Oil from the lubrication system must be drained. In the spring you will need to fill the system with new fresh oil.

How to fight moisture

The main negative factor in storing a chainsaw in winter is an increased level of humidity. Moisture tends to condenses on metal and other surfaces, which leads to a significant acceleration of corrosion processes.

If the chainsaws are stored in the winter in the garage, then it is necessary to periodically explode the room. Heat accelerates moisture evaporation. But the highest result is provided by the so.called dehydrators (drainers) of air. These are adsorbents that pull moisture on themselves and reliably hold it.

Dehydrators can be of various types. The most advanced electric models are. The average household dehydrator collects up to 1-2 liters of water per day. In order to save, the drainage can be included periodically, during periods of rains and slush.

If it is a pity to spend electricity on connecting a productive dehydrator, then you can do with an old grandfather method. We are talking about bags with silica gel. You just need to throw in a box with a packaged chainsaw three or two standard bags with an adsorbent at 10 (g).

How to store a chainsaw in winter

This is perhaps one of the few tools for which there is work in the cold season. True, the range of operating temperatures of the chainsaw is usually small due to the fact that it contains insistent parts, gas and oil. If the manufacturer guarantees the operation of the tool at a temperature of –10 ° C is a very good indicator, and such a saw can be used almost all year round. If you leave the summer cottage for a long time, then take care of proper conservation.

The “heart” of any chainsaw is a single.cylinder two.stroke carburetor engine. Another important element is the chain. It is the care of these two elements that most of the recommendations for conservation are devoted to:

• First of all, drain the remains of fuel from the tank, carburetor and oil for lubrication of the chain. For full production of fuel, you can start the chainsaw of an idle and wait until the gasoline is over. After that, wipe the gas tank dry so that it does not begin to rust. This is an option for prolonged conservation, at least 3 months. But there is a second option for those who are falling the forest or carrying out other works in winter. In this case, the tank is advised to fill with high.quality gasoline to the edges and leave for storage in this state. If you urgently need to cut down a tree. excellent, you have a completely finished technique at hand. But remember, gasoline, which after 2-3 frosty winter weeks in consistency will begin to resemble jelly, can even be disable; even a first-class motor;
• Using a wire probe or homemade nozzle, remove filter-endor filters from the fuel and oil tanks. Rinse them and set them back after drying or, if necessary, replace with new. Do the same with an air filter;
• Remove the saw chain and tire and clean them of the remains of sawdust, wood and dirt;
• Remove the clutch cover, thoroughly rinse it under a stream of warm water and let it dry. Lubricate the worm gear and screw of the side tension system of the chain;
• Remove the spark plug and clean it from soot and fuel residues. Pour 5-7 ml of motor oil into the candle hole and cranceize the engine for 3-4 revolutions so that the oil is distributed according to the connecting rod mechanisms and the cylinder-piston group. Leave the piston at the top (in the raised state). After that, set the candle in place, but do not put on the ignition terminal;
• Cover the saw tire and chain with protective lubricant and store wrapped in a piece of paper or fabric impregnated with oil;
• pack the tool and hide the removed parts into a dry, dark and nonsense place.

About once a month, perform the crankshaft to update the lubricant on the connecting rods and in the cylinders with the pistons.

If you have an electric drain, then all you need to conservation is to lubricate the saw tire and chain with protective grease.

Operation of chainsaws in the cold season: the main points

The house always has a task for a chainsaw, so sending it to the “winter holidays” is not always rational. In such cases, the tool is not fully stored, t.E. Without complete disassembly.

If you plan to work with a chainsaw in winter, store it and, in particular, the fuel mixture, in a well.ventilated, dry and warm, in extreme cases, an unheated room protected from external influences. ,

Before starting work, make sure that the fuel has a temperature sufficient for ignition, and that the oil in the tool lubrication has normal viscosity. Some models of the chainsaws are equipped with a hot air supply system to the carburetor from the cylinder cooling ribs, which reduces the risk of freezing of the air filter and prevents the formation of condensation on the carburetor.

Check the lubricant system before starting work

Run the saw on the cold with a closed throttle, having previously checked the quality of the lubricant and the tension of the chain. As soon as the work is completed, the tool cannot be immediately inserted into the room. This is guaranteed to lead to the formation of condensate, so you will have to remove it, disassemble and clean it.

STIHL 180 ms chainsaw. User manual. Malfunctions and solving the problem

STIHL equipment is a productive equipment designed to solve garden and production problems. Country manufacturer. Germany, where the main capacities of the company are located.

STIHL saws are one of the directions of the brand. Its assortment presents amateur, semi.professional and professional models. The tools are highly performance, good quality and ergonomic design.

Below we consider the line of saws, as well as the solution of the main problems that arise in the process of using the tool.

Stihl chainsaw oil

STIHL produces oils that are well suited for the tool.

The line of lubricants for the saw engines consists of the following models:

• STIHL HP. has a low level of excretion of harmful substances, made on a mineral basis;
• STIHL HP Ultra. synthetic oil, recommended for semi.professional and professional models;
• STIHL HP S. used for high.performance engines.

You can choose any STIHL saw oil, but it is better to adhere to the recommendations in the instructions for the tool.

The saw chain also requires lubrication. For her, you can use the oil of such brands:

• Forestplus. mineral oil;
• Bioplus is an environmentally friendly product, it is made on a plant basis;
• Synthplus. a semi.synthetic product can maintain abilities even in harsh conditions.

When mixing oil and gasoline for the Stihl chainsaw, 1:50 proportion is observed. For example, 20 ml of lubricants are added per 1 liter of fuel. During the running.in, you can increase the amount of oil.

Fuel for the chainsaw of STIHL

STIHL tool only works on a mixture of gasoline with oil. It is recommended to use fuel, the octane number of which will be above 90, without impurities. Otherwise cannot avoid clutch breakdowns and gearbox.

To dilute gasoline for the Stihl chainsaw, it is better to use the oil of the same company. Dilute fuel with lubricants in a ratio of 50: 1. If you do not adhere to these recommendations, the tool can work much worse. Oil can remain on the walls of the cylinder, blocking the spark.

How to start a stihl chainsaw

The manufacturer STIHL recommends starting a saw strictly with the instructions. This will extend the life of the product and will allow you to work with it correctly.

• Expand the case and take out the saw.
• Run the chain brake, for which it needs to be squeezed away from yourself.
• Click on the decompression valve.
• Squeeze the fuel pump.
• Take the lever to the position for cold launch.
• Install the tool on a flat horizontal surface.
• With your left hand, hold the saw by the handle, with the right pull out the starter cable.
• When the motor stalls, immediately transfer the combined lever to the middle position.
• Pull the starter cable.
• Immediately click on the gas, open the throttle.
• Pull the lever on yourself by releasing the brake.

You can start work on the site and processing wood.

Equipment features

Starting to study the issue of how to use the chainsaw “Husqvarna”, “Stihl”, “Friendship” or other varieties of such equipment, it is necessary to delve into especially every tool. All existing varieties are conditionally divided into three groups.

The first class includes household appliances. They are used in private operation when performing a small amount of work. Such chainsaws have low power. But for a home master of such functionality there will be more than enough. This is relatively inexpensive and light equipment.

Semi.professional chainsaws allow you to bring down trees. With their help, construction or repair work is also carried out. The operating time of the tool does not exceed 8 hours a day.

Professional chainsaws are able to work up to 16 hours a day. Their continuous operation time reaches 9 hours. This is expensive, heavy equipment. It can afford to buy only specialized companies, enterprises.

Adjustment of the carburetor of the chainsaw STIHL

It is carried out if the saw stalls when you press the gas. Previously, the carburetor is cleaned of pollution, change the candle in it and the filter is cleaned. Regulate the work at idle.

Settress Carburetor STIHL Carburetor

• First you need to turn off the tool and turn the two screws to the stop. l and h.
• The same bunches are turned into one revolution.
• Start a tool, warm up the motor.
• Squeeze the gas lever and turn the screw h until the speed is stabilized.
• Turn the screw La until the movement of the saw chain starts, after which I turn it on a quarter in the opposite direction.

After these manipulations saw, the gasoline chain STIHL should start working. If the problems remain, you need to work with the La screw and scroll it a little more.

Stihl chainsaw device

All brand saws have a similar design, but are equipped with different engines. This allows you to divide them into productive and household tools. To familiarize yourself with the specifics of the saw device in detail, you need to study its instructions. It indicates the features of the components and the rules of work are spelled out.

How to pull the chain of the chainsaw of STIHL

Before starting the chainsaw, you should fully prepare the tool for operation. The correct installation of the chain and tires, for example, guarantee not only high cut quality, but also your own safety.

The process of preparing for the work of the StiHL chainsaw will depend on which device tension device is used in a particular tool. There are only 3 types:

Fast tension system

This method allows you to install the circuit using a special installation wheel. In this case, you do not have to use an additional tool.

First you should prepare the workspace, laying down the soft coating. This will eliminate damage to the tool or the surface itself. After that, you can proceed to the installation of the chain, performing the sequence of actions:

Open the lamb nut and remove the lid.

Turn the stretch star to the right to the right.

Put the chain over the tire, starting from the top.

Check the accuracy of the location of the circuit. In this case, the cutter should be located at the top and be turned forward.

Set a chain with a tire on an asterisk. Track that the guide tire is approaching the bolt bolt.

Set the chain sprocket cover on the motor block, and then turn the nut until the chain sprocket is in contact with the engine body.

Crank the clamping screw in the direction of the tire. In this case, leading chain links should be located in the notch of the tire.

Twist the lamb nut until it is fixed.

Check the circuit for sagging and pulling.

The anterior tension system

For the correct installation of the chain, you will need to perform several standard actions:

Put on a soft surface: combined key, circuit, engine block and tire.

Bring the motor unit to the position vertically and unscrew all the nuts. After that, you can remove the lid of the chain star.

Move the tension device to the left so that the clamping element is behind the asterisk.

Check the position of the teeth that should be directed forward. Fix the tire with a chain on an asterisk, and then put on the bolts with a bacter.

Fix the tire with a chain on an asterisk, and then put on the bolts with a bacter.

Check the links that should enter the groove.

Tighten all nuts combined with a key.

Check whether the chain is pulled and whether there is sagging on it.

Side tension system

In this case, you will also need a combined key to unscrew the nuts. The steps are in many ways repeated:

Bring the motor unit to a vertical position using a combined key.

Spin the tension device until it stops to the left.

Check the position of the chain. The cutter at the top of the bus should be located in front.

Install a chain with a bus on an asterisk, hanging on a bolt with a pile.

Put on the cover on the motor block and tighten the nuts.

Crank the clamping screw so that all links enter the grooves.

Tighten all nuts with a combined key.

How to launch a stihl chainsaw

Do not forget to use protective equipment that not only guarantee your safety, but also provide comfortable work.

For the correct launch of the tool, you must observe a sequence of certain steps:

Activate the chain brake, pulling it forward.

Press the decompression valve and fuel pump button if they have a chainsaw.

Lower the combined lever to the end to put it in a cold launch position.

Install the chainsaw on the surface so that the cutting part does not touch the ground.

Step on the rear handle and slowly pull the trigger before the resistance.

Install the combined lever to the position of half.gas to open the throttle.

After starting the engine, press the gas lever briefly.

Let the chain brake pull the handle over yourself.

Some models are equipped with Ergostart technology, which provides an easier launch. An additional spring located between the coil and the crankshaft minimizes the compression pressure. Thanks to this, the loads arising due to jerks are completely excluded. This modification allows you to run the motor smoothly.

In addition, there is also a starting device Elastostart. This technology is a built.in damping element that absorbs the load when pulling the starting cable. With additional use of manual fuel pump and decompression valve, the stihl chainsaw is smooth, almost without jerking.

A decompression system is also used to ensure a slight start. This allows you to increase the valve opening time, which contributes to a smaller heat consumption, a decrease in compression pressure and minimization of swinging. Due to this, the number of necessary attempts for starting the engine is significantly reduced and the throne drive is reduced.

Some chainsaws are also equipped with a decompression valve and manual fuel pump. Both systems have individual advantages.

The decompression valve, for example, releases part of the compressed mixture from the cylinder out, reducing the force of traction of the launch cable. Open manually and automatically closes with the first ignition.

Manual pump is controlled by a button, which is made in the form of a soft cover. Due to the timely pumping of fuel, you will need much less starting moves.

In addition, the correct launch also involves compliance with safety precautions:

• Make sure that there are no outsiders near the place of work.
• Never work alone. If necessary, your partner will be able to provide you with the necessary assistance.
• Are at a distance of at least 3 m from the dressing site.
• Make sure that the working area is cleansed of possible obstacles, for example, branches and fallen trees. Slippery, icy or uneven surfaces should also be avoided.

Safety

Correctly selected personal protective equipment guarantees work comfort and ensure safety.

How to get without a starter

It will not work without a starter without a starter. manufacturers have not provided an alternative way to start this tool. And even if it can be started in any way, there will be a problem with the cooling system and the saw will not work. The fact is that a snail is installed in the starter that ensures the movement of cold air from the flywheel impeller to the cylinder. If it does not, then the engine will overheat and most likely jam.

Service of the chainsaw

Before the operation of the saw, it is necessary to check the amount of fuel each time. The degree of filling of the oil tank should be periodically monitored, this is very important to prevent a reduction in oil level. Before sawing, the degree of tension of the chain, sharpening of sharpening is tested. The tire bearings are lubricated monthly.

Upon completion of the work, the saw is cleaned of sawdust and chips. Rinse the air filter. the best option is a nylon or foam filter, unlike a felt disposable. Air filter cleaning will be required when interruptions in operation appear, swelling of the engine during sawing.

Wipe the cooler ribs, ventilation holes. Do not forget to clean the brake tape. It is advisable to use the prepared fuel mixture for 3-4 weeks. It should be remembered that careful care for the chainsaw largely affects the duration of the tool, the effectiveness of work, the lack of breakdowns and malfunctions.

For uniform wear of the tire, it is necessary to periodically turn it over the back of it. Experienced owners of chainsaws, in the recommendations of how to use a chainsaw, advise you to have three chains, which ensures uniform wear of the lead gear. It is impossible to cut a hungry chain, it is dangerous, the load on the engine increases, the saw as a result saws completely low.quality. crookedly or goes into one side. If a long break is assumed to use the saw, weaken the tension of the chain.

How to prepare a chainsaw for winter storage. Storage tips in winter in winter

With the onset of cold weather, many owners of the chainsaws simply send saw equipment to the shelf in the garage, until better times. At the same time, few newcomers know that the proper storage of a chainsaw in winter involves the conservation of equipment using special technology.

There is a special series of chainsaws that have admission to work in winter cold. Such models have a well.insulated case, as well as a carburetor heating system.

With prolonged storage of chain saw technology, a complete stop of the actual mechanisms occurs, which leads to the following negative consequences:

• Friction vapors and other nodes cease to get a lubricant, which leads to their drying out.
• The old lubricant turns into a thick jelly, which over time dries and tanks.
• Seals spoils, as well as filtering elements.
• The fuel is exhausted and loses its conditional properties.

In many cases, the owners of the chainsaws have to be perplexed that the chainsaws worked properly in the fall, and in the spring he flatly refuses to start to start. All the fault of the incorrect storage of a chainsaw in winter, during the cold season of the year.

General rules for conservation of technology

Any tool, regardless of the type and purpose, before laying on storage, you need to wash, dry and inspect the details for wear and replacement. There is nothing worse than moisture that fell into mobile or vulnerable details and mechanisms. Freezing in an unheated room, it turns into ice and damages the elements of the system. It is also advisable to drain gas tank gasoline for fire safety reasons. But for the clock, other recommendations. the equipment cannot be left “dry”, so the oil is not removed for the winter, but they are changed.

When stored, fold the equipment as indicated in the operating manual

The cutting parts (such as lawnmand knives) should be sharpened, and hinged joints should be cleaned of dust and dirt and grease. Check the condition of the fasteners and power cord of the power tool, if necessary, replace them without leaving until spring. Next, we consider each type of technique and the requirements for its conservation in more detail.

Optimal solution

For winter work, it is better to buy a chainsaw, specially provided for a total. There is a technique equipped with a hot air supply system to a carburetor from the cylinder cooling ribs. This reduces the risk of freezing of the air filter and prevents the formation of condensate on the carburetor. Many manufacturers (Makita, Stihl, Maruama) produce models in which you can switch the “winter” and “summer” modes using a special damper located in the lid. Since in winter mode the carburetor will be produced in advance heated air, icing is impossible.

Drain the remaining gasoline from the tank, drain the oil from the tire (lubrication of the tire and chain). Remove the shinkus of the saw, clean everything, wipe it, that’s perhaps all the conservation

Severstal was one of the first participants in the WorldSteel global program to reduce greenhouse gas emissions

Typically, chainsaws are used only in the warm season. Starting in the fall, their test check should be carried out, having determined whether the tool for maintenance needs. And if the chainsaws of Husqvarna for which are now quite affordable, you are in good condition, then it’s time to prepare them for the winter. The required procedures, of course, are noticeably different from intended for a conventional saw or shovel.

How to store a chainsaw in winter

This is perhaps one of the few tools for which there is work in the cold season. True, the range of operating temperatures of the chainsaw is usually small due to the fact that it contains insistent parts, gas and oil. If the manufacturer guarantees the operation of the tool at a temperature of –10 ° C is a very good indicator, and such a saw can be used almost all year round. If you leave the summer cottage for a long time, then take care of proper conservation.

The “heart” of any chainsaw is a single.cylinder two.stroke carburetor engine. Another important element is the chain. It is the care of these two elements that most of the recommendations for conservation are devoted to:

• First of all, drain the remains of fuel from the tank, carburetor and oil for lubrication of the chain. For full production of fuel, you can start the chainsaw of an idle and wait until the gasoline is over. After that, wipe the gas tank dry so that it does not begin to rust. This is an option for prolonged conservation, at least 3 months. But there is a second option for those who are falling the forest or carrying out other works in winter. In this case, the tank is advised to fill with high.quality gasoline to the edges and leave for storage in this state. If you urgently need to cut down a tree. excellent, you have a completely finished technique at hand. But remember, gasoline, which after 2-3 frosty winter weeks in consistency will begin to resemble jelly, can even be disable; even a first-class motor;
• Using a wire probe or homemade nozzle, remove filter-endor filters from the fuel and oil tanks. Rinse them and set them back after drying or, if necessary, replace with new. Do the same with an air filter;
• Remove the saw chain and tire and clean them of the remains of sawdust, wood and dirt;
• Remove the clutch cover, thoroughly rinse it under a stream of warm water and let it dry. Lubricate the worm gear and screw of the side tension system of the chain;
• Remove the spark plug and clean it from soot and fuel residues. Pour 5-7 ml of motor oil into the candle hole and cranceize the engine for 3-4 revolutions so that the oil is distributed according to the connecting rod mechanisms and the cylinder-piston group. Leave the piston at the top (in the raised state). After that, set the candle in place, but do not put on the ignition terminal;
• Cover the saw tire and chain with protective lubricant and store wrapped in a piece of paper or fabric impregnated with oil;
• pack the tool and hide the removed parts into a dry, dark and nonsense place.

How to properly store a trimmer for grass

Trimmer for grass (electric or lawn mower) is a popular and useful garden tool for mowing grass, weeds and small shrubs. The technique is quite complicated, you need to correctly contact it, but also store it. Particularly important is conservation for the winter. Sometimes the owners of such equipment simply throw it into a pantry or garage for the whole winter. In such conditions, by the next season, the unit may fail. Therefore, it is important to correctly approach the conservation and organization of storage conditions.

Which affects the characteristics of a trimmer for grass

The technical condition of motorcycles during storage can change due to such factors:

• The quality of the device itself. If the manufacturer used low.quality materials and components, they themselves become unusable faster, for example, rust.
• Package. Should protect against dust, moisture and mechanical damage.
• Temperature. Should not fall below 0 ° C. Especially relevant for battery models, since the battery in the cold quickly degrades.
• Humidity. Excess moisture leads to corrosion damage to parts.
• Training. Before storage, the device must be properly served.

Storage features

There are two main types of motorcycle. gasoline and battery. The rules of their storage are mostly convergen for some nuances. In any case, the conservation should begin with thorough maintenance and preparation of the unit.

Training

Preparation of a benzotrimer begins in this way:

• Fuel and butter.
• Let the apparatus work at idle so that it consumed all the fuel left in the carburetor.
• Spin and inspect the spark plug. The electrode should have a reddish color. If there is a car, the candle should be cleaned or replaced.

Eletric trimmer for grass should begin to be prepared for conservation as follows:

• Remove the battery. It must be stored separately in a cool place, but not at minus temperature.
• Check the condition of the wiring and contacts. If there are damage to the wiring or weak contacts, they need to be corrected.
• Check the condition of the brushes. If they have worn out, it is necessary to replace.

Further, the rules are the same for both types of motorcycle:

• Remove the remaining grass. She can accumulate between fixed nodes and knives. Blades also need to be carefully cleaned. If there is organic pollution on the case, they must be carefully removed.
• Dismantle the cutting knife. Check it for mechanical damage. If there is a part, be sure to be replaced, this can be done immediately or before the next season. Store a knife separately.
• If the lawn mower is equipped with a trimmer cord (fishing line), it should be dismantled and keep in a wet place until the next season. Before the new season for several days you need to leave in clean water. Thanks to this, the fishing line for the trimmer will remain elastic, which will extend its service life.

Where and what to store

It is extremely recommended to store motorcycles in limbo. The steering wheel often interferes, so it can be dismantled or simply turned the other way. As for the choice of place and packaging, the following options can be distinguished:

• The optimal storage location is a garage or a separate building for garden equipment. The main thing is that the room is dry and well ventilated.
• If there is no separate building, a trimmer for the grass can be kept in the pantry of the house or apartment. It is desirable that the room is not very dusty, which is especially important for electric motorcycle. A large amount of dust absorbs moisture, as a result of which it begins to conduct electric current, which is fraught with a closure.
• It is better to use factory packaging in which a trimmer for grass was sold. Very good if it has a foam, it will absorb excess moisture. In such a package, the device is not necessary to hang.
• If there is no factory packaging, you can use a cardboard box of a suitable size.
• You can apply a suitable cover of dense fabric, for example, tarpaulin. In such a package, a trimmer for grass will be conveniently hanging on the wall, to save space.
• You can build a box of boards or plywood. However, in such a box, the lawn mower will take up a lot of space.
• Trimmer for grass can be wrapped in a breathable fabric.
• If there is no packaging at all, it is recommended to store the device in a suspended form. This will protect the details from mechanical damage and will save place. But, it is important that there is no dust in the room, especially from building materials. For suspension, it is enough to mount a hook of the corresponding size into the wall.

Useful tips

To avoid premature failure of a trimmer for grass, follow the following recommendations:

How to prepare a trimmer for the grass for winter

The next instrument important for each summer resident is a benzotrimer. Its competent storage is one of the main factors of a long service to the owner.

• The place for wintering should be warm, with low humidity, isolated from temperature drops. The benzotrimer should not freeze, it should be wrapped in an unnecessary blanket or other moisture absorber.
• All fuel from the tank must be removed and the trimmer for the grass is idle, waiting for it to stall.
• Inspect the presence of a fuel with a light of the ignition. To do this, you need to turn it out and remove it. If the electrodes are red or close to this. everything is in order, another color suggests that they need to be cleaned or changed.
• The knife needs to be stored separately. Remove it, clean it from pollution, check the absence of cracks or chips.
• If there is a trimmer cord, you can extend the service life of it, keeping it in water. Thanks to this, the fishing line for the trimmer will retain its elasticity.
• For wintering, a trimmer for grass should be hung.

Serious technique: storage of cultivators and motoblocks

A large number of details and not the complete accessibility of all parts of this technique does not always allow a full preparation for winter storage, but it is necessary to do several stages of preparation:

• First of all, it is necessary to prepare the engine. After the fuel is merged and the remains are developed, you need to change the oil while the engine is still warm.
• We clean the filters: we update paper, my foam rubber, dry and soak in machine oil. We clean the fuel filter.
• The spark plug must be cleaned, dipped in gasoline. While it dries, fill the oil into the cylinder and distribute it using a thicket of shaft. After wrap the candle back.
• The engine and muffler are thoroughly cleaned of contaminants. The gearbox should not be cleaned with metal scrapers, you can damage protection and get consequences in the form of rust. It is better to use wooden devices, washing all the elements. After contacts of parts with water, they need to be dried;

Rules for caring for a chainsaw STIHL

Gasoline tools. an indispensable assistant in home and domestic affairs. STIHL units are most in demand, they are productive, equipped with a powerful engine, meet the proper safety requirements and are suitable for long.term operation. If you properly serve this equipment, it will last several decades. The tool needs to be chosen only from a large manufacturer in Kostroma, because only the original Stihl chainsaw will be able to fully perform all the work and will not let you down at a crucial moment. It can be bought for gardening, used for harvesting firewood from a forest or just for agricultural needs.

Chain saw is a category of tools that need special care. If you use high.quality fuel, oil and know the instructions and follow its rules, the chainsaw will last a long time, even if every day to work with trees and saw material. In this article, we will tell you how to care for the STIHL saw and give useful tips that will help during operation.

Basic rules for the care of a chainsaw

Whatever chainsaw of the Stihl from the lineup you bought, you need to be able to care for it correctly. Most operations can be performed with your own hands. we note the main of them.

• Before the first launch, check the presence of an air filter and the spark plug. You need to season oil for lubrication of the chain, pour gasoline into the tank and add motor oil to it. Use only high.quality fuel and specialized oils.
• After work, it is necessary to clean the tire from sawdust, land and other litter. So that the chain is constantly lubricated, during cleaning, check the condition of the oil channels.
• Take the chain regularly. as it is worn out, observing the gaps with the desired step in the row. Use a flat file and a special sharpening tool. The detailed process is described in the instructions.
• Before winter, drain the fuel and start the engine to burn the remaining fuel. Pour a little oil into the combustion chamber before wintering and scroll the crankshaft several times with a kick. In the spring, new filters and a light of ignition are usually installed.

If you follow these rules, the chainsaw will last a long time. follow these instructions. Detailed recommendations are written in the manual for the tool, do not forget to study this information. In case of questions or in controversial cases, it is better to contact the service center.