Parma Tractor Square and stalls. Resting the rings

The most common motives for the breakdown of the walk.behind tractor

The uniform tractor is equipped with an internal combustion engine (ICE) and as everyone else breaks over time, its repair and maintenance is carried out as well as for single.cylinder carburetor ICE for any other equipment. In the article, we will analyze in more detail the reasons why the same.based tractor is not started, as well as the methods for their elimination.

• A neutral speed is set to switch. Checked according to the pointer, or by simple rolling of the walk.behind tractor. on the neutral it rolls easily, without rotation of the engine.
• The air supply flap is placed in a closed position (indicated on the case at the lever of the damper).
• The fuel supply crane opens.
• The “Start” button is pressed or fixed on the handle (from the model).
• The handle of the hand starter is pulled to the hook hook. A smooth jerk (or several) ICE is launched.
• After starting the air supply, the air is opened.

Nuances. if a particular ICE is unstable at idle, the launch is carried out with a squeezed “gas” handle (a ajar throttle, “gas” for a third or half).

In detail, how to properly run the one.axle tractor, you can find out in

When the hot engine is launched, the airblock air filter is not closed at all. Buttons “suction”, manual pumping of fuel on a carburetor in four.stroke engines. The fuel-air mixture begins to enter (sucked) in the combustion chamber when rotating from the starter without preliminary let-the-up, which is used on almost all two-stroke one piston internal combustion centers.

We also recommend reading an interesting article on how to properly launch a single tractor. It contains many useful tips and nuances, which even experienced owners do not know about.

The main reasons why the one.axle tractor is not started

In most cases, the engine does not start for two fundamentally different reasons:

In addition, other serious malfunctions are possible-the lack of compression in the combustion chamber, just a gross mechanical breakdown of a node, starting from the starter, ending with a curved-shaped mechanism. It is worth noting that the nature of the malfunction and the repair of diesel motoblocks differs significantly from gasoline, in our article the information is mainly intended for gasoline.

Why does a one.axine tractor stall at a load?

Almost every engineer of the walk.behind tractor, regardless of the brand and model of the agricultural unit, came across a problem in which the same.based tractor starts up and stalls after 5 minutes of work. The main causes of this breakdown lie in the problems with the supply of fuel and breakdown of the ignition system of the machine.

As practice shows, if the unoic tractor stalls when working, then its owner should immediately inspect the details of the fuel supply system. First of all, turn out and look at the candle. if it is completely dry, this indicates that the fuel does not fall into the engine cylinder. After that, you need to make sure that a sufficient amount of fuel is present in the fuel tank. If there is gasoline and it is enough for work. inspect the fuel valve. it is possible that it is in a closed position. To launch the walk.behind tractor, just open the fuel valve and continue to work with the unit.

Another reason why the same.based tractor starts up and stalls after 5 minutes of work is to break down the ignition system. To determine that the unit is faulty for this reason is quite simple. take a look at the candles. if they are wet, then the malfunctions appeared precisely in the ignition system of the walk.behind tract. The best way out of this situation is to re.regulate the ignition system of the unit. All actions, at the same time, must be performed in this order:

• Remove the cover that serves the elements of the ignition system;
• Turn the flywheel of the motor until the contacts go out in Magneto;
• Using a special probe, measure the gap between the “anvil” and “hammer” of the ignition system of the motor block;
• After that, turn the flywheel until the moment the piston of the walk.behind. In this case, the latter must reach its upper point;
• Take the flywheel again until the moment when you hear a characteristic knock. this means that a overtaking coupling worked;
• Then turn the flywheel in the opposite direction so that the label on it coincides with the label on the body of the walk.behind tractor;
• Install the gap between the interruption contact and the fist. it should be 0.3 mm;
• At the end, fix the cam with a screw located above the part, and install the protective cover back into the motor block body.

After the above actions, the same.based tractor will no longer stall under load. The main thing in the event of such problems in the future is to try to quickly eliminate the breakdown, so as not to give the main mechanisms of the walk.behind tractor to be increased to wear and wear. It is also often a household unit stalls when tilted. This indicates an insufficient amount of fuel in the fuel tank. If you put the unit in a horizontal position, pull out the starter cable, and the engine starts, then you will need to add gasoline into the tank.

The causes of the malfunctions of the motor block and the ways to eliminate them

Malfunction: one.axic tractor stalls at loads

If the unoic tractor functions normally for several minutes, and then stalls, the reason usually lies in the fuel supply or in problems in the ignition system.

To find out what is the cause of the motoblock malfunction, you must first check how the fuel is supplied:

• Get a candle and inspect. if it is dry, then there is not enough fuel;
• check if the fuel is enough in the gas tank of the walk.behind tractor;
• Make sure that the fuel valve is open. the blocked faucet can be a simple reason that the same.based tractor stalls.

If the problem of the malfunction of the gasoline motoblock in the ignition system, it must be re.adjusted as follows:

• remove the cover that protects the ignition system;
• turn the moss engine of the engine until the contacts in Magneto;
• Using the probe, measure the distance from the anvil to the hammer;
• turn the moss to maximum compressing the piston;
• Once again, turn the moss before the appearance of a knock indicating the work of a overtaking coupling;
• Turn the moss in the other direction so that its label coincides with a mark on the body of the walk.behind tractor;
• set the distance from interrupting contact to a fist of 0.3 mm;
• fix the cam with a screw that is above the element;
• Install the lid in the body of the walk.behind tractor.

If the adjustment is made correctly, the unoic tractor will not stall during operation.

Malfunction: one.axle tractor works with jerks, with interruptions or at reduced power

If the unoic tractor on a gasoline or diesel engine begins to work with interruptions, you need to instantly turn off the unit and start eliminating the malfunction.

Continuing to work with a faulty walk.behind tract means to bring it to more serious breakdowns.

• If the engine of the gasoline walk.behind tract makes return movements, it is necessary to rinse the pump and hoses to supply fuel and replace the fuel with a better;
• When the unoic tractor works with jerks due to incomplete warming up the engine, you need to drown out the motor, let it cool completely, start and warm it up for ten minutes;
• If the engine power has fallen, you need to check and clean the filter system;
• If there is a wear of the ignition magnet, you need to replace the part with a new.

Malfunction: one.axic tractor smokes and stalls, the muffler makes unusual sounds

Possible causes of malfunction:

Methods for eliminating faults:

• With an excess of oil, drain the fuel, rinse the fuel pump and the hose system, pour new fuel;
• check the correctness of the gap between the electrodes;
• If it became obvious that the fuel does not completely burn, disassemble the piston system, rinse and dry the cylinder, correctly configure the carburetor.

Malfunction: one.axic tractor starts up, but stalls quickly

Such a malfunction happens if there are problems with contacts. What to do:

Another reason for the malfunction. the carburetor was polluted, and there is little fuel. Then you need to replace the fuel and reduce the amount of oil.

Malfunction: one.axic tractor stalls when heated

This problem arises due to excessive air entering the carburetor. With such a malfunction, the gas trigger should be squeezed out half. After the motor factory before the start of work, it is necessary to draw well.

If it is not possible to cope with the malfunctions of the garden motoblock, the unoic tractor stalls, the uniform tractor does not start, contact the Alfa-in motor blocks repair workshop using the high-quality repair of gasoline motor blocks using original components that will always be found in our warehouse.

The causes of the malfunctions of the motor block and the ways to eliminate them

Malfunction: one.axic tractor stalls at loads

If the unoic tractor functions normally for several minutes, and then stalls, the reason usually lies in the fuel supply or in problems in the ignition system.

To find out what is the cause of the motoblock malfunction, you must first check how the fuel is supplied:

• Get a candle and inspect. if it is dry, then there is not enough fuel;
• check if the fuel is enough in the gas tank of the walk.behind tractor;
• Make sure that the fuel valve is open. the blocked faucet can be a simple reason that the same.based tractor stalls.

If the problem of the malfunction of the gasoline motoblock in the ignition system, it must be re.adjusted as follows:

• remove the cover that protects the ignition system;
• turn the moss engine of the engine until the contacts in Magneto;
• Using the probe, measure the distance from the anvil to the hammer;
• turn the moss to maximum compressing the piston;
• Once again, turn the moss before the appearance of a knock indicating the work of a overtaking coupling;
• Turn the moss in the other direction so that its label coincides with a mark on the body of the walk.behind tractor;
• set the distance from interrupting contact to a fist of 0.3 mm;
• fix the cam with a screw that is above the element;
• Install the lid in the body of the walk.behind tractor.

If the adjustment is made correctly, the unoic tractor will not stall during operation.

Malfunction: one.axle tractor works with jerks, with interruptions or at reduced power

If the unoic tractor on a gasoline or diesel engine begins to work with interruptions, you need to instantly turn off the unit and start eliminating the malfunction.

Continuing to work with a faulty walk.behind tract means to bring it to more serious breakdowns.

• If the engine of the gasoline walk.behind tract makes return movements, it is necessary to rinse the pump and hoses to supply fuel and replace the fuel with a better;
• When the unoic tractor works with jerks due to incomplete warming up the engine, you need to drown out the motor, let it cool completely, start and warm it up for ten minutes;
• If the engine power has fallen, you need to check and clean the filter system;
• If there is a wear of the ignition magnet, you need to replace the part with a new.

Malfunction: one.axic tractor smokes and stalls, the muffler makes unusual sounds

Possible causes of malfunction:

Methods for eliminating faults:

• With an excess of oil, drain the fuel, rinse the fuel pump and the hose system, pour new fuel;
• check the correctness of the gap between the electrodes;
• If it became obvious that the fuel does not completely burn, disassemble the piston system, rinse and dry the cylinder, correctly configure the carburetor.

Malfunction: one.axic tractor starts up, but stalls quickly

Such a malfunction happens if there are problems with contacts. What to do:

Another reason for the malfunction. the carburetor was polluted, and there is little fuel. Then you need to replace the fuel and reduce the amount of oil.

Malfunction: one.axic tractor stalls when heated

This problem arises due to excessive air entering the carburetor. With such a malfunction, the gas trigger should be squeezed out half. After the motor factory before the start of work, it is necessary to draw well.

If it is not possible to cope with the malfunctions of the garden motoblock, the unoic tractor stalls, the uniform tractor does not start, contact the Alfa-in motor blocks repair workshop using the high-quality repair of gasoline motor blocks using original components that will always be found in our warehouse.

Why is the one.based tractor working with interruptions?

Among other typical malfunctions of the walk.behind tractor, a number of such breakdowns can also be distinguished:

• The aggregate motor hits the return. this indicates the use of poor.quality fuel for refueling the unit. In this case, you will have to not only replace the fuel, but also thoroughly rinse the fuel pump and fuel supply hoses;
• The same.based tractor works with jerks. the reason for this lies in the insufficient heating of the motor. Be sure to drown out the engine, wait for it to cool completely, and again start the motor, giving it at least 10 minutes for full heating;
• The motor block does not noticeably pull, the engine power has decreased. in this case, you need to check and, if necessary, clean the air and fuel filter. Another reason for this breakdown lies in the wear of the magnesium magneto. It is best to immediately replace the part without trying to restore it.

The owner of both gasoline and diesel motoblock is equally often faced with this kind of malfunction. In any case, you need to immediately stop working with the machine, and as soon as possible to eliminate its breakdown.

Do.it.yourself motoblock repair

Some elements can be replaced independently. However, it is not recommended to take up the repair of a walk.behind tractor with your own hands if it was bought less than 1 year ago. Under the terms of warranty service, any manipulations should be carried out only by employees of the service center, otherwise the right to free repairs will be lost. To determine that the technique was disassembled will not be difficult, t.to. In many details, manufacturers install seals.

It is not difficult to make an adapter for a walk.behind tractor with your own hands if you collect everything you need to work, to understand well.

Repair of the fuel system

It is impossible to call the exact system of disassembly of the walk.behind tractor, t.to. The location of the parts and their fastening depends on the model. Most often, the failure of the pump is the cause of the fuel system failure. Disassemble the detail and inspect it. The element must be replaced in the presence of external defects. A single tractor can stall even because of a small dente, barely noticeable to the eye. If there is no breakdowns, the pump needs to be cleaned and installed in place.

Repair of the ignition system

The motor will stall if Magneto breaks. You can check and repair it yourself. To do this, you need to clean the candle. Check its performance. If it is working, put on a part of the cap. Below, bring to the Magneto body and rotate the flywheel located on the engine. The lack of a problem speaks of the appearance of a spark. Otherwise, it is necessary to replace magneto, otherwise malfunctions in the work will lead to wear of all mechanisms of the ignition system.

Transmission repair

The gearbox failure does not allow the engine to work without failures. First you need to make sure that the reason for the self.willed shutdown of the equipment is precisely in the breakdown of the transmission. This is evidenced by:

• slippage slip;
• noise in the gearbox;
• the inability to return the clutch to its original position;
• heating of transmission nodes;
• oil leaks;
• Strong vibration of the walk.behind tractor.

The same-based tractor can stall due to wear of individual checkpoints. It’s not difficult to see it. It is enough to disassemble the transmission and check all the elements for external defects. You can adjust the axial position, t.to. The huts of the shafts are erased because of it, breaking the equipment out of order. Make sure the bearings are in good condition. If they have worn out, they need to be replaced.

Opinions of buyers

Rares are rarely returned due to insufficient strength. The technique is made so that the ingress of stone into important details can not disable them. But even a stable material wears out. This is the main reason why the same tractor stalls. Owners of such special transport recommend independently conducting inspection at least once a month. By noticing the defect in time, you can prevent unexpected breakdown.

To assemble a mini-tractor from a walk-behind tractor without making errors, you will need step-by-step instructions and.

The motor cultivator stalls under load if the gaps are greater or less than the norm. You can adjust this yourself. The main thing is to notice the problem in time. For example, you cannot ignore if “something” shoots into the muffler. Most often, problems arise under load. You cannot experience the technique for strength, starting it again with each problem. If you do not eliminate the cause of the failure, you can finally disable the part. Then you have to buy it. Motoblocks of the company “Cascad” during engine breakdown can lead. In this case, you need to check the battery charge.

Equipment greatly simplifies work in agriculture. But sometimes even the most reliable unoic tractor starts and stalls, what is the cause of the failures, not everyone knows. It is difficult to figure out this if the owner has no experience in mechanical engineering. However, you can replace most details in the MB without the help of a service center, and for diagnosis you will not need anything except the compressor.

For what reason does it shoot into the muffler

First, let’s figure out the physics of the process of what is happening, what shoots there and why, because there are no bullets and shells in the muffler, there is only fuel.

Engineers conceived the engine design so that fuel is ignited in the engine combustion chamber, at a certain moment, when all the fuel supply and gas supply channels are closed. But, if you break this idea and fuel will burn with an open graduation valve, you get a shot or cotton, which we will clearly hear.

There are only 2 main reasons why the uniform tractor shoots into the muffler and this:

• Ignition problems. With late ignition, fuel ignition occurs when the exhaust valve is open and the sound of the explosion breaks out, through the muffler. It is necessary to adjust the ignition.
• Excess fuel. For problems with the carburetor, it begins to serve more gasoline in the fuel mixture, it does not burn and falls into the muffler, and then it is ignited in it and the cotton turns out in it. You need to deal with the cause of the carburetor overflow. The easiest way is to replace the carburetor with a deliberately working.

There is another reason-this is burnt valves, this happens very rarely, but still possible.

We recommend watching a video, the author of which just talks about these very problems and how he managed to eliminate this malfunction.

Why the engine is poorly started on hot

First of all, you need to check whether the air damper and the position of the gas handle are in the correct position. They must be set as it is written in the instructions for the operation of your walk.behind tract.

If the levers are in the right place, then there may already be a problem in a candle or engine itself. When heated, the resistance of the candle changes, and it can give a weak spark insufficient to launch. To solve the problem, it is necessary to replace the candle with a new.

In the case of the engine, the following occurs, when heated, the metal expands the compression drops. What makes it difficult to start.

There may also be a problem in heating the carburetor, hot air is supplied to the fuel mixing chamber, there is little oxygen in it, which makes it difficult to ignite the fuel mixture and the engine of the unoic tractor is poorly started to be hot.

Why does a one.axine tractor stall at a load?

The problem is when the same.based tractor works with periodic swallows and does not develop speed. almost the most common among gasoline and diesel units. If the unoic tractor starts and stalls, the main causes of this phenomenon should be sought in the fuel and incendiary system, the malfunctions of which can occur after 5 minutes of work.

If the unoic tractor does not develop turns and stalls spontaneously, you must check:

• Aerofilter. when it is clogged, it is cleaned by its surface, washed or blown with a vacuum cleaner.
• quality of the refueling fuel;
• incendiary system. its diagnosis begins with a candle, by the external state of which they judge the functionality of the ignition.

In addition to the candle, other ignition breakdowns are:

• irregular gap between the electrodes;
• mechanical damage to the electrocope;
• Unresolved angle between the magnetic part and the reel.

Do.it.yourself repair is allowed if it is provided for by the user’s guidance for a particular motoring model;

• Milter. the motor stalls at work and does not develop momentum due to the fault of the clogged muffler. To free it from combustion products, it is soaked in water with detergents and after washing. it is dried;
• a carburetor, the configuration of which may be incorrect;
• cylindrical details, due to which the motor does not develop speed under load. This can only be checked by a compressometer.

It also happens that the cultivator stalls sharply when tilted in both directions or only left or right. Most often this occurs due to the fault of the insufficient oil level. At the time of inclination, the lubricant residue sensor in the crankcase can be triggered, which automatically blocks the motor.

Why does one.axle tractor shoots in a silencer?

Often, in case of malfunctions of the motor system, the unoic tractor not only does not develop turns, but also makes obvious cutting hearing sounds emanating from the muffler. After that, he smokes and stalls, which causes obvious users concern.

The reason for this problem may be:

• Excessive flow of oil into gasoline or diesel, due to which its combustion is accompanied by the release of unnaturally caustic smoke. In this case, the repair is reduced only in cleaning the fuel system and refueling with high.quality combustible;
• failure in the ignition adjustment or failure of its components. first of all, pay attention to the gap between the electrodes and, if necessary, put it in accordance with the operating instructions;
• incomplete combustion of fuel in the motor cylinder. In this case, the repair of the motor block engine begins with disassembling the entire cylinder.piston group, which is cleaned and checked for defects. It must be remembered that after such manipulations it will not be superfluous to reconfigure the carburetor.

The engine of the walk.behind tractor is bad to start hot

The question of why the engine of the walk.behind tractor stalls when heated is quite simple to solve. The whole essence of the problem lies in the overabundance of the air supplied to the carburetor of the walk.behind tractor. Part of it is mixed with a mixture of gasoline and engine oil, and the second part cools the carburetor. As a result of this, the temperature of the carburetor becomes much lower than the temperature of the aggregate motor. Such a problem is observed only in the process of working motoblock. When its engine is jamming, the carburetor, on the contrary, lends itself to heating from the hot walls of the motor.

During heating the carburetor of the motoblock, the remnants of fuel begin to actively evaporate, filling all the void in the device, including the air filter and the inlet collector. This leads to a complete disappearance of the fuel, which is why the unoic tractor does not start with a heated motor.

To fix this problem, it is necessary to act in a certain algorithm at the start of the walk.in on the hot unit in a certain algorithm. Your main task is to achieve the combination of the mixture so that the motor can start. This will need:

• In the process of starting the hot motor, squeeze half the gas trigger;
• Do not try to press the gas trigger over and over again, otherwise you will only aggravate the situation, since during the frequent pressing of the gas trigger, the fuel pump will supply new portions of fuel to the carburetor, which will lead to pouring the motor;
• After several attempts to launch with a half.pressed gas trigger, you will start a motor block engine, after which you will need to calculate 2-3 times and continue to work.

This procedure will eliminate the increased load on the hot motor, so the main details and mechanisms of the walk.behind tractor will not succumb to excessive wear.

All of the above methods will help effectively cope with typical breakdowns of the most famous manufacturers of motoblocks. They are equally successfully used by owners of agricultural units of the brands of Honda, Agro, Cascade and Neva.

In this section, we will make out a malfunction of the motor blocks and cultivators of all brands “Salute”. Neva, bison, etc. D., And their elimination and repair. Most problems are characteristic of all types of motor blocks, their engines and other components.

Checking the filter

Even the most unprepared mechanics will be able to simply check the air filter for pollution. Remove the filter from the case and increase the engine speed. The work of a car without a filter will not cause him any harm for the period of the short period of time.

If the engine is still smoking, then something else causes the case. You may be a little disappointed with this, since the renewal of the air filter, you, the easiest and most affordable solution to this problem.

Run the engine without air filter

Otherwise, maybe subsequent checks are made by a competent diesel mechanic, because the subsequent part of the work is a check of the nozzle. The presence of a cunning injector implies the low quality of the burning of diesel fuel, due to which dark smoke is often done. There is an option to establish new nozzles, but we advise you to get professional help to suspend the release of dark smoke from a diesel engine.

The engine of the motor block smokes white smoke

The bad working tact also causes such symptoms, since no matter what general inefficiency that allows accounting for accounting (software) leads to a fireless combustible. This means that you may see smoked blackened clouds of exhaust gases.

The main malfunctions of the motoblocks

Diesel and gasoline engines have different motorized resources. For the first, a normal figure is 4000 m/h, but the latter can provide only 1,500 m/h. Despite this, diesel models of motoblocks are not in high demand. After all, both when buying and during operation, they are much more expensive. Therefore, most likely, you work with a walk.behind tractor equipped with a gasoline (carburetor) engine.

All breakdowns that can occur during the operation of agricultural minute can be divided into two categories:

• Engine malfunctions:

• starting problems;
• Dot in work.

• Malfunctions of other nodes and mechanisms:

• improper clutch work;
• breakage in the gearbox;
• problems with the chassis;
• control and automation malfunctions;
• malfunctions of the motor block systems (cooling, lubrication, etc.).

Read also: How to check the vertical as a level

In many ways, the success of the repair of a suddenly failed machine depends on the correctness of the diagnosis. As for maintenance, it is carried out precisely in order to identify small malfunctions, which will subsequently lead to serious.

Malfunctions of gasoline and diesel garden motoblocks

Garden Unoa Tractor is a very useful thing in the household. With a good walk.behind hand, work in personal plots goes much faster. But motoblocks, like other household equipment, sometimes break.

The most common malfunctions of garden motoblocks:

• The same.based tractor stalls at loads;
• The same.based tractor works with interruptions;
• The same.based tractor smokes, stalls, muffler makes unusual sounds;
• The same.based tractor does not start;
• The same.based tractor starts, but stalls quickly;
• The same.based tractor stalls when heated.

Malfunction: one.axic tractor stalls at loads

If the unoic tractor functions normally for several minutes, and then stalls, the reason usually lies in the fuel supply or in problems in the ignition system.

To find out what is the cause of the motoblock malfunction, you must first check how the fuel is supplied:

• Get a candle and inspect. if it is dry, then there is not enough fuel;
• check if the fuel is enough in the gas tank of the walk.behind tractor;
• Make sure that the fuel valve is open. the blocked faucet can be a simple reason that the same.based tractor stalls.

If the problem of the malfunction of the gasoline motoblock in the ignition system, it must be re.adjusted as follows:

• remove the cover that protects the ignition system;
• turn the moss engine of the engine until the contacts in Magneto;
• Using the probe, measure the distance from the anvil to the hammer;
• turn the moss to maximum compressing the piston;
• Once again, turn the moss before the appearance of a knock indicating the work of a overtaking coupling;
• Turn the moss in the other direction so that its label coincides with a mark on the body of the walk.behind tractor;
• set the distance from interrupting contact to a fist of 0.3 mm;
• fix the cam with a screw that is above the element;
• Install the lid in the body of the walk.behind tractor.

If the adjustment is made correctly, the unoic tractor will not stall during operation.

Malfunction: one.axle tractor works with jerks, with interruptions or at reduced power

If the unoic tractor on a gasoline or diesel engine begins to work with interruptions, you need to instantly turn off the unit and start eliminating the malfunction.

Continuing to work with a faulty walk.behind tract means to bring it to more serious breakdowns.

• If the engine of the gasoline walk.behind tract makes return movements, it is necessary to rinse the pump and hoses to supply fuel and replace the fuel with a better;
• When the unoic tractor works with jerks due to incomplete warming up the engine, you need to drown out the motor, let it cool completely, start and warm it up for ten minutes;
• If the engine power has fallen, you need to check and clean the filter system;
• If there is a wear of the ignition magnet, you need to replace the part with a new.

Malfunction: one.axic tractor smokes and stalls, the muffler makes unusual sounds

• With an excess of oil, drain the fuel, rinse the fuel pump and the hose system, pour new fuel;
• check the correctness of the gap between the electrodes;
• If it became obvious that the fuel does not completely burn, disassemble the piston system, rinse and dry the cylinder, correctly configure the carburetor.

Malfunction: one.axic tractor starts up, but stalls quickly

Such a malfunction happens if there are problems with contacts. What to do:

Malfunction: one.axic tractor stalls when heated

This problem arises due to excessive air entering the carburetor. With such a malfunction, the gas trigger should be squeezed out half. After the motor factory before the start of work, it is necessary to draw well.

If it is not possible to cope with the malfunctions of the garden motoblock, the unoic tractor stalls, the uniform tractor does not start, contact the Alfa-in motor blocks repair workshop using the high-quality repair of gasoline motor blocks using original components that will always be found in our warehouse.

Failures of the launch system

If when checking the candle turned out to be wet, but the motor does not start, then detecting the malfunction will be much more difficult:

• may give a failure of the ignition system;
• Due to the depressurization of the compounds, air leaks may appear;
• there may be an unknown air damper in the carburetor;
• Carburetor breakdown.

The ignition system fails is an unpleasant moment, but you should not panic and immediately call a specialist. First you turn out and inspect the spark plug. If you find a dozen on it, clean it with a sandpaper, rinse with gasoline and let it dry completely. Very often after such a procedure, the motor begins to work normally.

If the motor still does not start, and you feel quite qualified, check the size of the gap between the electrodes. The desired value is indicated in the instructions of the manufacturer’s factory, but due to constant vibration during operation, it may change, and the same-based tractor may stall on the go. Adjust the gap to the desired size, bending the side electrode.

With the rest of the ignition system problems, it will not work to understand the move. If you burn out candles or wiring insulators, then they need to replace. You can also close the “stop” button to the mass, and until the closure is eliminated, the engine will not start. Also, the reason that the engine is not started is a violation of contacts in candles or a gap violation between the magnetic shoe and the starter. Finally, the starter itself may be damaged and it will have to be changed.

If the one.axine tractor does not gain power normally, it is worth checking its muffler. The fuel combustion products clog the muffler over time, forming a thick layer of carbon on its walls, so it should be cleaned periodically. To do this, the silencer must be removed by plugging the exhaust hole with a clean rag, rinse first in gasoline, and then cleaned with detergents from the carbon fiber, and finally dried with a hairdryer.

Sometimes the same.based tractor stalls during operation and from elementary overheating. If, with a completely open throttle, you click on the gas handle, and the motor, instead of accelerating, loses speed, then this is a clear sign of overheating. The same.based tractor needs to be stopped and let it completely cool, and then run it again.

This is far from the whole list of reasons why your until recently, a completely proper unoic tractor can stall even under a short load. Almost all the nodes of the motoblock during work are subject to significant loads, so small malfunctions and breakdowns are not uncommon. Therefore, having discovered that something is wrong with the walk-behind tractor: extraneous noise, twitching, strong vibration, etc.P immediately turn the engine. And only after the motor cools down, you can start searching and eliminating faults. But this is already a topic for another conversation.

Screeches the starter, the cord gets out

Can scream if there are a lot of lubricants on the balls. You need to clean the balls and places in the ratchet where they are inserted.

The cultivator issued several claps, began to “swim” turnover

Most likely, the power system does not cope, or the level of fuel in the tank is low, the bias of the axis of the float is possible and perhaps under the needle valve the garbage is, you need to remove and check the air filter, nozzles.

The material will be updated, we are waiting for Комментарии и мнения владельцев with questions, stories about identifying a particular malfunction and ways to eliminate it. Also, see the answers to the questions about a particular model of the walk.behind tractor on the page of its description.