Daw for cutting PVC panels. How to make a hole in the PVC panel: secrets of cutting material

How to cut PVC panels: how to saw correctly

The use of an electric jigsaw is quite justified, but it should have a speed adjustment. For cutting, special files for organic glass are used.

If you do not have to buy them or you need to cut it already, then use wood files. The main rule exists here: the teeth should be small, and the cutting speed is small. At high speeds, the cut begins to melt and becomes white. For some products, such white seams are not suitable.

Tip: in order to remove the burrs, and make it cut with a clean flame of a gas burner. In extreme cases, you can adapt the lighter.

Electrician allows you to do curvaline cuts. For this purpose, you need to choose narrow saw canvases.

Tip: When buying files for organic glass, pay attention to the marking. It should have Latin letters MP.S

Cutting mp files.S curvoline details

During cutting, pay attention to the speed of the tool. The higher the speed, the more the feed rate can be

The speed and turning speed are selected experimentally so that acrylic does not melt. During cutting, it is necessary to use a protective mask on the whole face from fragments flying at high speed.

If the details of a complex curved shape, then for cutting organic glass it is permissible to use a nichrome spiral.

How to cut plastic panels: four tools and what to expect from them

What can most often be found in the arsenal of any master of the finisher? Naturally, the most popular tool in work. Among him there will probably be a knife sharp as a razor, a hacksaw for metal, on wood and, possibly, even an electric jigsaw. It is the listed tools that are used most often for cutting plastic panels. They cut all these tools in different ways, but be that as it may, they do it, and the quality of the cut is enough for wall decoration.

Knife. Should be very sharp and be able to cut one side of the panel in one passage. In fact, in the process of cutting the plastic with a knife, the master cuts out exclusively its front surface. then the panel simply breaks, after which the back side is cut off again with a knife. Everything is simple, but the cut itself turns out to be uneven and one side of the plastic as it were bent, which prevents the PVC panel strip in the start profile or connector. You have to trim everything and achieve a normal edge, spending time on this process.

Wood hacksaw. It has large teeth and in most cases does not cut plastic panels, but tears them at the edges. In general, the option is not very successful and it is better to leave it in an extreme case, when there is nothing else at hand.

Kryazuvka for metal. Unlike the previous option, the canvas of such a saw is equipped with a small tooth that cuts plastic very carefully and evenly

The only “but” of its use is the need for careful work. a metal arc, holding a hacksaw canvas can leave dents on the connecting locks, which will not allow plastic to do with each other normally with each other.

The electric jigsaw is essentially the most ideal tool that you can think of to solve the issue than cutting the PVC panel? It is important to choose the right file. the canvas for the metal will be the perfect option. In the process of cutting, it is necessary to reduce the longitudinal course of the canvas on the jigsaw to a minimum. only in this case you will receive a clean and even cut, which you practically do not need to bring to the condition the maximum that you have to do, it is a small number of burrs.

By and large, if you are not embarrassed by the melted edges of the panels, you can cut this material by means of corner grinder. As an option, a disk saw is suitable, but for this it will need to be equipped with a small tooth. In general, anything is suitable, but you need to understand that some tools create torn edges, while others do, although a clean, but not quite even cut.

Which tool is suitable for cutting plastic panels?

There are many ways of cutting plastic in the arsenal of masters of finishing work. And everyone who is engaged in repairs on their own can choose any of these methods, use a professional tool or improvised means, based on their needs and capabilities. Let us consider in more detail all the pros and cons of each method:

When cutting, place the panel with the front side

To successfully cope with the task, it is worth knowing some secrets of plastic cutting. This will significantly reduce the number of rejected and spoiled panels, and protect the novice master from extra waste of time, money, and above all, from injuries.

• If you carry out finishing work in the cold season, do not cut the panels that have just been listed from the street. Let them keep warm to room temperature. The best option is to spend at least 1 night in room temperature. Otherwise, the plastic, which becomes fragile in the cold, will be broken down by large pieces, cracks can go along the entire length of the panel.
• Regardless of which method of cutting you have chosen, the panels are worth the front side up (photo above), otherwise the panel can be deformed and its installation will cause difficulty. In addition, if you make an incision from the inside, the front side can be covered with microcracks, which will show themselves only over time, completely spoiling the design. It will not be superfluous in advance to mark the fishing line for the trimmer of the cut, for this a simple pencil or felt.tip pen is suitable (which will easily be erased from the surface after the end of work) and the student ruler.
• To cut several PVC panels at the same time, you need to fold them with a pile and make a two-point support for this stack so that the panels do not sag. It is also worth resting the opposite edge of the stack into the wall, otherwise the panel will shift during cutting and as a result you will get details of different lengths.

Safety precautions

When cutting plastic panels, especially using an electric tool (jigsaw or corner grinder), is highly likely that sawdust and fragments will fly away from the material. Therefore, it is worth in advance to purchase protective glasses and gloves that protect the eyes from injuries, and it is recommended not to remove them until the end of the work.

Regardless of what tools you decide to use, the above tips will help you avoid the mistakes of most inexperienced finishes and create a cozy interior that will please for many years.

Tools for cutting panels without defects

To adjust the length or width of a pair of lamella, enough ordinary hacksaw. But if there are many sheets, you should choose a more powerful tool.

2 types of cutters are used.

• Mechanical. cutting is produced, putting physical effort. The speed is completely dependent on the capabilities of the employee. This method is preferable to figure cutting, since patience and accuracy are required here. Mechanical include hacksaws, knives, cutters, manual jigsaws.
• Power tool. the employee directs the cutting blade, but does not make his own efforts. Thus, you can cut a much larger number of panels. Representatives of the category: circular electric saw, corner grinder, electric.

Manual tool is cheaper to use. Electric requires connection to the network, but it is much more efficient.

For cutting, they take a stationery, construction and even a kitchen knife. The best option is construction, as it is better balanced for such work. When using a stationery, for example, you will have to cut under the square, which is not too convenient.

For cutting along 3-4 sheets, the painting knife is most suitable. He has a very thin and sharp blade, a fishing line for a trimmer cut is also thin and neat. However, across the lamellas with a molar knife, it will not work to cut.

Hacksaw

Manual hacksaw is ideal for work. The fishing line for the cutting trimmer is thin, without chips, since small cloves do not grab the fiber. You can cut along and across, diagonally, since the speed here is determined only by the applied efforts, the risk of temperature melting panels is extremely small.

Electric

Allows you to perform a cut along and across several sheets at once. The tool has the advantages of manual, but when using it, the employee is much less tired. However, due to the speed of the teeth, figure cutting with it is extremely difficult to do with it.

You need to work at minimum power so that the plastic from heating does not deform. If the tool is heated, you need to stop and wait until it cools down.

Corner grinder

For cutting panels, the angular grinder is not suitable: the speed of rotation of the disk is very high, the material heats up during operation. Therefore, they take low.power models and the thinnest disc. 0.8 or 1 mm. Undoubted plus: a thin and accurate razm, regardless of the temperature of plastic and weather conditions. Corner grinding can cut the lining in the cold. Minus: highlights a lot of dust.

Circular

The circulation saw is also designed to work with a large volume of material. The tool provides a perfectly even cut several sheets at once. Cutting in any direction is allowed. For a file, you need to take a special disc for plastic or model for soft wood, plastic and aluminum.

Prevention of errors, safety precautions

When cutting plastic panels at home, it is important to observe the rules for handling the material. Otherwise, a flat cut cannot be achieved.

• The panels are placed with the front side down. As a rule, the outer side of the panels reproduces some kind of structure, has a relief. During direct cutting, the texture is crushed, cracks and dents appear. Such defects are also possible on the inside, but they remain invisible and do not affect the user characteristics of the material.
• Before the work, a fishing line for a trimmer cut is marked on a pencil or felt.tip pen. This noticeably simplifies processing, especially if the cut should be done figured. The marks are easily erased from the smooth surface of the material.
• It is forbidden to cut plastic in the cold. The panels immediately after transportation or transfer from the cold are left in a room with a temperature of up to 10 ° C for a day and only after that begin work. When cooling, the material becomes fragile and it will be very difficult to cut it.
• To reduce the preparation time, several sheets often cut at once. You can do this, but at the same time you need to follow some recommendations. Sheets must be laid on a two.point support so that they do not bend during operation and do not sag. Put the panels tightly and accurately. It is advisable to rest the opposite edge of the pack into the wall to avoid the displacement of the sheets relative to each other.
• During cutting, a fairly large amount of dust is released, so it is better to perform work in a respirator or in a gauze bandage. In addition, the appearance of small crumbs and fragments is possible. Their edges are not too sharp, but can cause an injury. When cutting, you need to wear glasses, protect your hands with gloves.

The appearance of microcracks from the wrong side, some manufacturers consider the norm.

How to cut PVC panels correctly

You need to start with the preparation of a place for cutting, it should be comfortable, ventilated (with the work of some tools, well, a lot of garbage and dust). If there is an opportunity to perform cutting in the yard or on the street, you should use it.

If you already know how you cut the PVC panels at home, it is worth preparing a tool and a tool. Depending on the choice (find the necessary blades, sharpen the knife, choose the desired disk or canvas).

Prepare plastic panels, make measurements if you plan a figure cut to draw shapes and patterns on the surface of the sheet. You can use a marker or felt.tip pen. Do not worry, this material is easily laundered from the surface of the panel.

It is recommended to make thorough measurements before sharp.

Important! Some tools allow you to cut several sheets at once. For convenience, you need to fasten them with building clamps so that the sheets do not fidget. And it will be more comfortable to work.

Must be cut or cut with plastic panels, you need to put it with the front side. The rule is relevant for both one canvas and for several folded in the stack.

Conveniently cut the panels folded into a stack. So you can get a large number of necessary details at once.

For sawing panels into two parts that will be used in further work, they are placed on two supports, the gap between which is no more than 10 cm. The side of the panels is leaning against the wall. To cut off an unnecessary fragment on the panel (not very large sizes), the desired part is put on one wide rack, fixed, rested on the wall and the work is done.

Wonderful device if the sheets lie on two

How to prevent mistakes

The main mistake when cutting the sheets and working with plastic panels is not the knowledge that PVC sheets cannot stand low temperatures. You need to work with them at a temperature of plus 5 degrees per Celsius, or even more. If the temperature is lower. the viscosity of the panels decreases, which will lead to chips and zazubin along the cut line. at best. In the worst case. the plastic panel just cracks or crumble in the hands.

Plastic panels. a material that does not tolerate high temperatures and is sufficiently fragile. This should be taken into account when cutting.

In any case, inaccuracies, errors and punctures are possible. Who does nothing. he is not mistaken and does not study on his mistakes. You just need to know the necessary information, follow the rules, take into account recommendations, calculate everything a couple of steps forward and then there will be much less errors.

Before starting work, read the advice and recommendations of specialists. This will help to avoid errors and spoiled material.

Cutter

Such a device is convenient when the speed and high.quality cut of the workpieces are important to solve the problem. The speed of such a tool is high, at the same time, quality is better than any of the described above. But, when working, you need to carefully inspect the panel for possible chips and lay it out of the wrong side to the cutter, and with the face. the supporting surface. This is due to the fact that the cutter can be pushed 2-5 millimeters of the surface of PVC blanks.

The tool simplifies and accelerates installation work. Buying a cutter will close the question forever than cutting off a plastic panel, and other methods will no longer be relevant. Using it, it is important to remember that it will not be possible to make a trim in place with such a tool.

Electric

The use of such a power tool will help to cope with the sharp panels and reduce the complexity compared to a hacksaw or a construction knife. It is convenient to use an electrician when preparing a large number of blanks.

When performing work, the cut place is first marked on the front surface, and then smoothly cut off the required size, conducting the tool along the marking line. Cellophanes or other material is placed under the supporting paw of the jigsaw, which will prevent the possibility of applying scratches on the PVC panel. In the case of simultaneous cutting of several blanks, they are fastened with plastic clamps or wrapped with transparent adhesive tape. At the same time, the front surface is best isolated from adhesive tape (lay a sheet of paper).

How to cut PVC panels

The PVC panels are very in demand today, because they can not only sheathe the walls in the corridor and the hallway, as well as the ceiling on the balcony, but also use it in the bathroom, if necessary and the lack of means, instead of ceramic tiles. Polyvinyl chloride not only withstands various changes in the temperature regime, but also tolerates the moist environment perfectly, and the diverse design of plastic panels allows you to create a very unusual design of the room without prejudice to quality. Another advantage is that all work with the appropriate tool can be done independently.

Universal cutting for cutting plastic panels

PVC panels cutting tool

PVC panel is a polyvinyl chloride that flows into a special form under high pressure, which necessarily includes about 40 % of the natural crushed chalk. Coloring occurs using thermal printing or a better, but expensive method. offset printing. That is why to cut the panel, you need to use a special, but affordable tool.

It is worth considering that a good construction tool for cutting will not cost cheaply, and in order not to be in vain to rush with money, it is better to buy something high-quality right away:

• The universal cutter is produced by various brands, both local and foreign production. The panels can be cut without any oscillatory movements. It is recommended to purchase a saw 2 sizes: wider-2.5 cm by 4 cm and for hard-to-reach places-1 cm per 2 cm. Using the cutter, you can cut the panel both along and across without much physical effort, the cut is very neat and even. The only minus is the rapid wear of the files, and the price is quite high both on the tool itself and for components to it;
• Maular knife. For cutting panels, you can use knives. Kitchen knives are suitable for cases when you need to urgently repair a small area. Since the blade of the knife is thick, the cut turns out to be rude and inaccurate, and the process itself is laborious and long.term. In extreme necessity, it is better to give preference to a ceramic knife for Bukhankaa. Ideally, cutting wall and ceiling panels is better with a painting knife. Its blade is quite thin and sharp, and the cut is even and neat. True, only the upper part of the panel is cut, if you put forward a blade of about 3 mm (in the form of a small beard), and the lower part is ill. The advantages of this tool are at an affordable price, the blade is easy to change if necessary. But the process of work is quite long, and you can cut the panel only along;

Maslar knife for cutting plastic panels

• The hacksaw copes well with the set task of cutting plastic panels. over, this tool is in the arsenal of any owner. Before you decide on how and how to cut the PVC panels, you need to choose the best hacksaw option. Professionals recommend giving preference to a hacksaw for metal. When using a hacksaw on wood, the teeth of the instrument should be small and transverse, and not divorced in different directions, since the cut will not be so jagged and “fluffy”. The process of work in this case is more laborious and long. But when lining the walls of the same height, several panels can be cut at the same time, without making special efforts, it is enough to fold the panels in a flat pile. It is not recommended to press the tool too much, so as not to damage the material. This is an ideal option when you need to perform a small front of work on your own and I do not want to spend money on the purchase of an additional tool;

Cutting for cutting plastic panels

Knife.hairedwood for cutting plastic panels

• The power tool allows you to quickly and easily cut the material of absolutely any thickness and size. Most often it is used by masters specializing in panels sheathing. Such power tools include:

• Electrician is used for sawing both vertically and horizontally, moreover, it allows you to cut round, oval and other types of figures of irregular shape in the panel. It is recommended to give preference to files with minimal teeth, not more than 0.8 mm. In this case, the incision will not be “torn”. The greater the power of the jigsaw, the faster it will turn out to cut the material. It is convenient to use a file for metal, it does not stupid from polyvinyl chloride. If necessary, you can simultaneously work with 5 panels, smoothly fixed them with special clamps, but in this case the jigsaw should have a fairly high power;

Electrician to cut plastic panels

• Corner grinder can also be attributed to sawing power tools. It allows you to well and conveniently cut off a piece of any size. But for simplicity of work, it is better to give preference to a small and mild corner grinder so that you can hold it with one hand. For cutting, discs from 0.8 mm to 1.2 mm are used. The cut is perfectly even and undeveloped. Corner grinder can be used at any temperature mode. The downside is the presence of a large amount of fine dust and at high speeds the plastic may begin to melt, while highlighting a specific smell;

Corner grinder for cutting plastic panels

• The circular saw copes with the task perfectly. But when working with it, you should not make much effort in the form of “pressing” to accelerate the process, the material must be cut exclusively at low speeds.

Circular saw for cutting plastic panels

To say, the better to cut the PVC panel is quite difficult. It all depends, first of all, on the volume of expected work and on human skill and knowledge. Before starting work, the panel is necessarily entered for a couple of hours in a warm room, this will exclude cracking and breaking the material during cutting. So that the cut is not noticeable, the panel is always cut down down the wrong part. With simultaneous cutting of several panels, they are necessarily fixed from the 2nd sides by clamps or press. During operation, the power tool is recommended to protect the eyes with special glasses.

Molar knife

The easiest pvc cutting tool. But an unusual kitchen or boot, here you need only a molar knife.

His blade is still new, very thin and sharp. And when it is stupid, the blade can be replaced at the moment. Bite off part or inserting a new. An ordinary knife is inconvenient, it cannot be sharpened quickly. And also, he will not be so thin.

Molar knife is limited in capabilities. You can cut the panel only along. Of course, you can try to make a cut and across. But nothing good can work out of this.

How to cut panels along? Within the framework of the article, it is difficult to explain. However, the basic principle will be described.

The blade extends at a short distance of 3 mm.

On the back of the panel, select the place where the slot will be made.

Then we cut out the strip, from ribs to the rib (we are talking about the inner ribs of the panel). A slot is made near the rib, then a cut is made near the neighboring. We make cuts along the entire length.

A strip of plastic falls, the groove is formed.

Then, from the same back side, you need to make a shallow incision near the desired rib. And break the body on it.

The molar knife has advantages: speed, noiselessness and simplicity. And its disadvantages are that the panels can only be cut along.

Lobby

This tool can be called the main. A jigsaw well has a minimum of shortcomings. You can cut the panels along and across. You can cut figures with ovals and other broken things.

The jigsaw has a feature. He tears the edge of the panel in places where it remains to cut very little. At this time, very often panels burst (especially in the cold).

Therefore, it is worth using a file with a minimum tooth. For ourselves, we chose a Bosch metal canvas with a tooth of 0.8 mm. This saw will protect you as much as possible from a torn section.

If the jigsaw works at high speeds, you can cut such a file very quickly. This saw for metal, from cutting plastic products, it does not stupid.

The main plus of the jigsaw is universality. Cut the PVC panels, you can both along and across. In any spatial position.

The downside of the jigsaw is weight, the presence of a wire. With an incorrectly selected canvas. torn cut.

There is one secret

When you have to harvest a lot of sticks, frame size. For example, it is necessary to cut off at once 20-30 pieces.

And so as not to cut one piece each time, but increase the speed. You can resort to one secret.

You will need clamps (bench presses) as in our photo. Take several at once, usually 5 pieces. Consider that they do not stick out a friend-drill and clamp them with bench presses. Two pieces on each side of the panel.

And saw calmly. In this way you can cut to 5 panels. You can cut off more, but the Bosch saw does not give such an opportunity.

You will expel the cutting process five times and make your work simpler.

How to cut plastic panels at home: choice and nuances of using different tools

Typically, their cut in everyday life is carried out through very common devices that are available in the arsenal for many owners. Despite the possibility of cutting the PVC panels by several popular ones in the repair and accomplishment of the accompanying tasks, it is advisable to use the tools of tools in any situation in any situation. For example, not all devices are successful if you need to cut a large amount of material, which also needs to be found out and taken into account before the work starts.

Kryazuvka for metal

The canvas of such a hand tool has small teeth that provide neat and even cutting plastic panels. Resort to the use of hacksaw on metal is optimal in situations when it is required to carry out perpendicular cutting of the material. When it cuts the PVC panels along or diagonally, certain inconveniences arise that adversely affect the speed of work on the work.

The only significant disadvantage of this tool is the mandatory compliance with the limiting caution when using it, since the metallic arc holding the canvas can lead to the appearance of dents in the places of connecting locks, which is why difficulties will appear during the butt of products to each other.

Among the advantages of the knife.haired woman for metal include the possibility of simultaneous sawing of several panels. To do this, the material should be folded in one stack and be fixed in order to avoid displacement or deflection. To exclude damage to the products, cutting the tool is necessary without severe pressure. If you have a little material to cut, then it is more than enough. In a different situation, it should be borne in mind that work with him will take a slightly larger amount of time than if you use an electric tool.

note! Khocks on wood often have large teeth, which often tear plastic panels at the edges when trying to perform the cut, which should be used in compliance with extreme caution and only in extreme cases when there is no other suitable tool at hand and there is a small amount of work to be ahead.

When cutting products from PVC, you can use several varieties of devices. It is possible to make a cut of plastic panels with a regular knife, although it is quite difficult and if the need for processing 1-2 products arises, it is quite enough, for example, if you need to replace the damage during operation of the material, which manages to avoid the purchase of an additional tool. If large.scale work is planned or a cellular structure has, then it is necessary to consider other available options.

A more preferred solution in the cut of plastic panels is the use of painting or construction knives with the presence of sharp interchangeable blades provided. When the cutting element is stupid, it can be easily replaced by others, which is one of the advantages, because the sharpening of a conventional tool takes a significantly more time.

The blade of the knife used should be sharp so that for one first passage they managed to cut the front side of the material. After its cut, the product needs to be broken. The formed minor defects at the site of the cut mainly visually do not affect anything, since at the end of the installation of the skirting boards that mask them are carried out.

Among the minuses of construction knives, one can note the inconvenience of cutting the products diagonally and across the existing ribs of stiffness, as well as a fairly high speed of losing sharpness with the established blades.

The stationery device also manages to perfectly saw off the excess, using a ruler or a square in the process of work. Another optimal option for plastic panels is the use of a loaf of ceramics with special small teeth along the edge of the edge.

Corner grinder

It is one of the best tools when it is required to cut such products from the PVC, providing both high convenience and the speed of work carried out. When installing a cutting circle, it is possible to carry out not only direct, but also figured cutting of plastic panels, which is one of the main advantages of using corner grinder. When working at high speeds, the instrument disk is able to spoil the material, leading to the melting of its edges, which must be taken into account and excluded. For cutting plastic panels, it is optimal to use metal circles.

The traditional corner grinder has quite compact dimensions and weight, so that the tire of hand, if it occurs, is only after a rather large period of time, which is often enough to perform all the required work with it with it. An important disadvantage is that the products often subjected to processing at the end of the cut need additional grinding through a special machine. In the case of the initial absence of such a tool and the presence of other suitable devices in its arsenal, it is best to give preference to them.

Electric jigsaw

One of the best options for performing a cut of plastic panels not only across, but also throughout their length, as well as diagonally. With the help of an electric jigsaw, even edges are made, and the work itself takes a small amount of time. Carrying through it is necessary with a preliminary shutdown of the pendulum passage and the minimum speed, which allows excluding too much heating of the material at the place of passage of the cutting element.

Rules for cutting plastic panels

To fulfill their high.quality sawing, it is necessary not only to choose the right tool and find out the features of its use, but also to prepare the material in advance and adhere to certain norms that allow it to eliminate its damage and increase in expenses, simplify work, and prevent injuries:

• Regardless of the plastic panels used when cutting the process, the process should occur when the material is the front side up. Otherwise, when performing the cut, after some time, microcracks will occur on the outside with a huge probability, which in the future will lead to a deterioration in the appearance of the decoration.
• To simplify the work, before cutting the plastic panels, it is necessary to apply the marking on their surface by means of a pencil or marker.
• When cutting products using an electric tool, for example, an angular grinder or jigsaw there is a huge probability of departure in different directions of not only sawdust formed during the passage of the cutting element along the intended line, but even small pieces. Given this, throughout the entire cut, you need to be in protective glasses and gloves that will protect the eyes and hands from getting possible injuries.
• Before the saw, the material should lie down for some time in the room in which it will be installed. This is especially important when the plastic panels were in a cool place or in the cold and is made so that the products are acclimatized. Otherwise, non.compliance with this rule can lead to their fault when cutting due to increased fragility. For example, when performing a saw along the products located in this state, they are often covered with cracks. The material should be provided at least 12 hours, and preferably 1-2 days, for which it will acquire room temperature. It is not necessary to use additional heating devices for this, so that the heating of products from the PVC occur naturally.

Having found out how to cut plastic panels at home and related important nuances can dwell on the most suitable option for yourself and, if you need to buy or take the selected tool for rent, start the cut of pre.purchased material.

Hacksaw

Scabble. a universal tool that is available in the arsenal of any master. It can easily cut wall panels made of plastic if you purchase a special cutter. With the help of a hacksaw, the cutting process takes more time, but with a small amount of work, this does not significantly affect the duration of the wall cladding.

When sawing the plastic with a hacksaw, the following nuances must be taken into account:

• For sawing PVC, use a tool with small dentures for wood (transverse sawing) or metal.
• You do not need to make strong efforts to saw plastic, otherwise the material can be damaged.
• With a hacksaw you can cut several panels at a time at a time, folding them with a pile.

Keep in mind that when processing plastic, the incision can turn out to be jagged if you use a tool with dentists diluted in different directions.

Power tool

The most impatient can be used to drink PVC panels using a power tool. For these purposes, any device that is at hand at the master is suitable. This method allows you to quickly cut the plastic, saving a lot of time. Cutting is performed using:

Important! It is recommended to cut plastic exclusively at low speeds, since with high it begins to melt, releasing toxic evaporates, and the incision turns out to be torn.