DIY matto. Advantages of using a chainsaw to create a moped

Bicycle, moped, karting, ATV from a chainsaw with your own hands

The versatility of gasoline chain saw was proven not only by their multitasking and functional capabilities, but also by the abundance of beneficial homes that the craftsmen learned to do with their own hands. They save money on the purchase of expensive factory devices on which most people do not have money. But, as they say, a goal for inventions is acute. Therefore, speaking of chainsaws, many represent not only foresters or pruning of a fruit garden, but also winches, ice blocks, boat motors, corner grinders, sawmills, which technically competent masters learned to adapt from all their favorite gasoline tools.

Means of movement deserve no less attention. bicycles, mopeds, pictures, ATVs and much more that can be collected using a chain saw with a gasoline engine. About how and from what to recreate them and surprise others with an incredible motorized design, we will talk in this article.

Do.it.yourself motion

Not every happy bicycle owner is delighted with the need to pedal and spend his hand. The more convenient and less expensive in force is a motorized bicycle.

Do not make a bicycle with a motor from a chainsaw of a chainsaw as it seems at first glance. This will need:

• bike;
• Dawed with a power of a gas outlet of at least 2000 watts. this indicator will depend on whether it can move. As practice shows, engine power in 2 liters.With. It is enough that the motorcycle bike develops speed up to 40 km/h;
• tank for the future fuel tank;
• cable from the old bicycle;
• the handle, so that there is the opportunity to regulate the throttle;
• bolted screeds, nuts and other small consumables for creating mounts;
• Connecting elements to create a message from the engine.
• We aggregate the drive shaft. remove the rear wheel tire and put a tire with a diameter of up to 2.5 cm. This equipment will help to accept the engine speed, and like a gearbox, reduce the number of revolutions;
• We weld the powerage stand. it will help to install the engine from the chainsaw;
• Alteration of clutch. you can use centrifugal from the factory saw, connecting it to the wheel;
• Adapt the gas tank. it can be located next to the engine, or on the frame;
• We fix the wire from the incendiary system of the motor on one of the bicycle handles;
• attach a cable from a carburetor to the gas handle so that the control of the throttle is simple and fast;
• Equip the motorized carcass with means of protection: mirrors, lantern, and proceed to the test of a homemade bicycle from a chainsaw.

As you can see, the engine from the chainsaw is not so difficult to put.

Do.it.yourself motion

Not every happy bicycle owner is delighted with the need to pedal and spend his hand. The more convenient and less expensive in force is a motorized bicycle.

Do not make a bicycle with a motor from a chainsaw of a chainsaw as it seems at first glance. This will need:

• bike;
• Dawed with a power of a gas outlet of at least 2000 watts. this indicator will depend on whether it can move. As practice shows, engine power in 2 liters.With. It is enough that the motorcycle bike develops speed up to 40 km/h;
• tank for the future fuel tank;
• cable from the old bicycle;
• the handle, so that there is the opportunity to regulate the throttle;
• bolted screeds, nuts and other small consumables for creating mounts;
• Connecting elements to create a message from the engine.

The process of how to put the engine from the chainsaw on the bike is as follows:

• We aggregate the drive shaft. remove the rear wheel tire and put a tire with a diameter of up to 2.5 cm. This equipment will help to accept the engine speed, and like a gearbox, reduce the number of revolutions;
• We weld the powerage stand. it will help to install the engine from the chainsaw;
• Alteration of clutch. you can use centrifugal from the factory saw, connecting it to the wheel;
• Adapt the gas tank. it can be located next to the engine, or on the frame;
• We fix the wire from the incendiary system of the motor on one of the bicycle handles;
• attach a cable from a carburetor to the gas handle so that the control of the throttle is simple and fast;
• Equip the motorized carcass with means of protection: mirrors, lantern, and proceed to the test of a homemade bicycle from a chainsaw.

As you can see, the engine from the chainsaw is not so difficult to put.

Tips and recommendations

On the forums you can find a lot of useful tips, how and what to do correctly when assembling a moped from a chainsaw and great. Fulfillment of simple wishes and parting words from practice will help Amators avoid annoying misses when constructing a moped from a chainsaw.

• Since the improvement of your bike will significantly increase the load on all its nodes, first of all, you should make sure of the excellent condition of the bicycle.
• The engine from the chainsaw after transformations will turn into a home.made cycle motor, so the initial parameters of the engine should be strictly designed: mass. up to 6 kg, volume up to 50 cubic meters. cm.
• In order to avoid fire hazardous situations, carefully test the condition of the fuel tank.
• The transmission of the force on the wheel to the wheel depends on the correct installation and tension of the belt.

How to make a moped from a chainsaw?

The dream of the youth of most of our fellow citizens was and remains a moped. It develops higher speed and has a structure, more perfect than the described mototor. Buy a ready.made moped. pleasure is not cheap. We will tell you how to make it from improvised materials.

• a motor from a working powerful saw (in our version is a model of “friendship”);
• 2 wheels from the old bicycle;
• pipe with a diameter of 2 cm (metal);
• cable;
• bicycle stars; as well as forks;
• The old spare parts from the motorcycle are a ready.made fuel tank, headlight, if desired and the seat, although it can be done with your own hands;
• steering part;
• Gas lever.

• Cook the frame to which we connect the wheels from the bicycle, fork, as well as a gas tank and a lantern;
• We adapt the motor. the installation composition will depend on the configuration of the frame;
• We fasten the gas tank and the battery;
• We check that the newly installed elements do not dangle;
• We make a chain gear. it will allow the wheels to take the torque of the motor and move. You can take a belt instead of a chain pulley. But we must not forget that its wear will be noticeably higher;
• We set up the ignition system. we connect the battery and brake lever with it;
• We adjust the exhaust pipe.

The assembly process is completed: you can start testing a moped.

DIY Motosamit

No less well.known home.made, which was learned to produce domestic “kulibins”. We will need it to recreate it:

• a scooter designed for the weight of the person who will control them. It is desirable that he initially has a manual inhibition system. The pneumatic wheelbase of the scooter should be durable;
• a chainsaw with which the engine is removed- medium and high-power models are suitable.

The process of assembly of a scooter looks simplified compared to previous homepages:

• First, remove the motor base and fix it in the back of the scooter frame. We observe that motor and wheel stars coincide;
• We adjust a manual accelerator with a sink of a motorcycle. this is how the operator will be able to control the movement process;
• If necessary, equip the scooter with a brake pedal, but in most cases. a lever for manual control of a scooter is enough for its full operation.
• Testing a self.scatter from a chainsaw. in case of serviceability, a new motorized device is ready and can be operated.

How to independently make a snowmobile and other homemade homemans from a chainsaw friendship

The main advantages of the chainsaw are friendship: simplicity of design, reliability and low cost. It was developed in 1953. and produced until the beginning of 2000. For the entire time of production, its design remained unchanged, but some nodes were modified.

Depending on the installed carburetor and the ignition system, the MP-1 engine, which was equipped with friendship, develops from 2 to 4 liters.With.

Technical characteristics of the chainsaw of the Urals are higher than that of the saw friendship. It has a more powerful engine (5 liters.With.), has less weight (11.6 kg) and high productivity. But due to the high fuel consumption and the automatic lubrication system of the chain in the manufacture of home-made devices, such a saw is used less often than friendship.

The manufacture of a self.propelled house from a chain of imported production will cost more. For the operation of such a device, high.quality oil and fuel will be required. And in the event of a malfunction, a specialized and expensive repair will be necessary.

What can be done

Snowmobile

There is a simple scheme for the manufacture of a snowmobile based on children’s snow scenes. In this design there is a ready.made loading frame with a pilot’s place and steering control. The alteration of transport is reduced to strengthening the side skis and fixing the caterpillar unit with the engine on the frame.

To strengthen the skis, profile pipes or metal channels are welded to their ribs, and hull support bearings are installed on top. The height of the amplifier depends on the diameter of the tension (front) roller. To ensure good adhesion to the surface, the lower point of the video should be at the same level with skiing.

The caterpillar node frame is made from the corner and profile pipe 30 x 30 x 2 mm. The length of the frame is calculated taking into account the installation of the subframe for the engine in the rear, and the width is limited by the size of the snowball (200-230 mm). The stretch device consists of a guide that moves and is fixed on the frame using a bolt. It is mounted in the front of the pendulum and provides the longitudinal displacement of the shaft.

Wheels from the old hand trolley are used as the rollers of the leading and driven shafts or drums made of plastic are made. The diameter of the rollers depends on the type of drive. The pendulum must also be equipped with caterpillar support rollers. To prevent axial displacement of rollers, spacing bushings are installed on the shaft. Alternative. the use of support skis.

In the manufacture of a track from a conveyor tape (3-4 mm) on both shafts, gear wheels of a snowmobile of a snowmobile Buran are installed on both shafts. They are located in the center of the shafts, and support rollers are fixed along the edges.

The conveyor tape must be cut along 2 equal widths of the site. The distance between the blanks should correspond to the width of the gear from the drill. The tracks are made from a plastic water pipe cut in half (40 mm) with a wall thickness of 5 mm or from an aluminum profile. They are fixed on the caterpillar with bolts, spring washers and nuts. The distance between the tracks should correspond to the gear pitch. After installing the tracks of the edge of the caterpillar, fastened in a similar way.

Also, caterpillars can be made of 2 chains from a motorcycle. 2 stars are installed on the edges of the leading and driven shafts, on which every second tooth is grinding. This is necessary in order to fix the tracks on the chain.

The support rollers are installed in the center of the shafts. In addition to supporting the caterpillar, they act as guides for chains, so they should fit tightly to their inner edges. The tracks are made of aluminum profile and attached to each even link chain using bolts or rivets. A drive star is installed on the leading shaft from the outside of the pendulum.

A subframe with a platform for attaching the gearbox of the chainsaw is mounted in the rear of the pendulum. To carry out a stretch of the drive chain of the subframe’s support, it must be mobile and ensure the alignment of leading stars.

After assembling the caterpillar node, it is fixed on snowball and the engine is mounted. To ensure the safety of the chain drive and caterpillars, they are covered with protective casings.

A snowmobile from a chainsaw has a lifting capacity of 100 kg and is able to overcome snowfields up to 1.5 m high.

Helicopter

In the middle of 60 g. Students of the Aviation Institute presented several models of home-made helicopters (X-3, X-4, X-5). As their power plant, screw.engine blocks were used. They consisted of 4 engines from the chainsaw of friendship, which were connected by a common gearbox. The estimated speed of the last model was 157 km/h, and the flight time. 1.5 hours.

But the MP-1 engines were not recognized enough for light aviation models, so the helicopters could not pass flight tests.

Moped

You can make a home.made moped from a bicycle and a chainsaw. To do this, a small bicycle star is welded to the clutch shaft shaft, and a large star is installed on the left side of the rear wheel sleeve. To achieve the optimal gear ratio (1: 8), a pedal node with a carriage is cut out of the old bicycle frame. Such a homemade gearbox must be fixed on the engine housing.

The resulting design is fixed on the rear trunk and connected by a bicycle chain to the left star of the rear wheel. On the steering wheel, it is necessary to install a gas handle from a moped, which is connected with a cable throttle. The estimated speed of a home.made moped with 27 “wheels is 75 km/h at 5000 rpm.

Snowman

To assemble the snowman with your own hands, you need to make 3 main nodes:

• Screw. The shaft is made of a metal pipe with a diameter of 30-40 mm. A star from a motorcycle is welded to its edge, and to the central part. 2 shoulder blades (140 x 100 mm) made of 2 mm sheet. For the manufacture of the screw blades, it is necessary to cut 4 rings (external diameter 300 mm, internal. 220 mm), which are cut, stretched and welded in pairs on both sides of the blades. At the edges of the shaft, the blades are fixed using a rod.
• The frame of the snowman from the chainsaw is made of 2 mm steel sheet. Side ribs are welded by a semicircle with a radius of 160 mm. The body is made of 1 mm sheet. A round hole (160 mm) is cut in its upper part and a groove is installed for snow removal.
• The frame is made from the profile pipe. Its main nodes: an engineer for the engine, the spacecraft of the frame and chassis (wheels or skis).

The preparation of the engine consists in replacing the saw star with a motorcycle similar. When connecting the ICE drive to the screw, it is necessary to ensure an even stretch of the circuit, without distortion.

How to make a moped from a chainsaw and a bicycle

You should start by searching for a suitable motor. The heart of a chainsaw is suitable for this role. Use friendship. Remember the power. A homemade moped will not be able to move if the engine power is less than 2 liters. With. To create a bicycle with a motor from a chainsaw, you will need other components with your own hands:

• battery;
• pulleys, gears;
• gear belt or circuit;
• drive cable;
• clamps for fastening;
• Tools: screwdriver, pliers, etc. D.

The main place on which the elements of the future unit will be placed is the bicycle frame. Here, the fasteners on the upper pipe are mounted on the junction of the pipes passing under the saddle and the front lower. the engine, near the gas tank.

The next step in the assembly of a bicycle with a chainsaw engine manufacturing-gear rats-chips. Using these elements, the force created by the engine will be transmitted to the rear wheel.

Use wheels with an external limiter the size of a musical disk to create pulleys.

Do not forget about the strength and reliability of fastening parts.

Moped assembly continues, we mount the collected details:

• The front handle is connected to the engine shaft.
• We fix the second pulley on the rear wheel bushing.
• We put on the belt on the gear rates. If you use a chain, instead of pulleys, take the gears.

Having put the gas station motor on the bike, we proceed to the connection. We connect the working engine compartment with the battery, mount the ignition mechanism. An integral stage of assembly of a moped is a bunch of handle for the brake and motor. Adjust the tension of the connecting cable so that with the handle the engine easily starts.

Ignition from a chainsaw to a motorcycle

Spare parts of the chainsaw are also used to modernize outdated or requiring transport repair, such as a motorcycle. To improve this vehicle, the ignition system is often used from the saw.

• flywheel;
• spacer for a flywheel with a key;
• fan;
• coil with a high.voltage wire;
• aluminum plate for attaching the coil;
• Bolts, nuts.

The ignition from the chainsaw is suitable for motorcycles of ant, Izh Planet. Unlike Magneto, such ignition is reliable and durable, not afraid of shaking and water.

Evgeniy:

Made such a toy for his son. Made together, he helped to paint, and at the same time delved into the basics of technology. After trial testing, happiness was unlimited, because the scooter turned out to be a worker and how he developed excellent speed on a home.made. Because of my mass, I did not even try to ride it, but I think I would make it not far from.

Moped from a chainsaw. Tips and recommendations

Do.it.yourself motorcycle motorcycle is a way out for those men who do not want to spend on a car and its subsequent service and who do not like to pedal the bicycle pedal. In this case, a moped of a chainsaw and a bicycle, which you can assemble with your own hands in the garage, buying some necessary, missing details and spare parts will be a great way out of the situation. The process of alteration itself is not particularly difficult.

Before starting the assembly or in the event of questions, you can always turn to drawings and numerous video reviews available on the Internet.

How to make a scooter unit

Consider how to assemble a one.axle tractor from a scooter. For such assembly are used:

• scooter motor (4 liters are quite enough.With.);
• pre.shortened rear axle from the Lada car;
• gearbox (from a combine or other car).

Instead of the gearbox, you can install two chain stars that connect the engine to the gearbox, and the gearbox with the bridge. The variator from the scooter can be installed on the engine. The battery is installed above the gearbox.

Since the scooter engine has its own exhaust system and starter, the car will be not wy. In the front of the walk.behind tractor, you can put the headlight using the switch. This will facilitate the work in the dark, especially if the device is adapted for transporting goods.

Unine.tree from the chainsaw friend and Urals

Consider how to assemble a one.axle tractor from a chainsaw friendship. Assembly of the unit from the chainsaw engine Friendship is very simple. The motor is minor and compact, so the frame can be assembled from the pipe. In addition to the engine, a reverse gearbox and fuel tank are attached to it. The pipe curved in the upper part serves as a holder to control the device. The speed handle is installed on it.

We’ll figure out how to make one.time tractor from a chainsaw with your own hands. Step-by-step instruction:

• A drawing is created. This is a very important stage in the creation of the unit, without which it will not work to make reliable equipment. All spare parts with places of fastening should be clearly marked and all sizes should be marked.
• Creation of a frame. It is a cube in which the corners are 32×32 mm. A motor is installed on the upper corners of the frame, and under it. the fuel tank. For intermediate relying of the shaft in front, vertical racks are installed. And to mount the bearings, you will need supports to the longitudinal angles.

You can create a homemade unoic tractor from a motorcycle. This will be a more powerful device, a motorcycle engine is used for it. For example, a motorcycle engine is suitable.

Since the speed of the unit is low, a forced cooling system is necessary.

The easiest way is to install a fan. And so that the air is directed to the cylinder, the protective coating is used. They can serve as an old fuel tank from a motorcycle. Mopeds are also suitable for making the unit.

Also make a single.axic tractor from a chainsaw of Urals. The agricultural unit can be collected not only from the Urals, but also from the taiga, as well as any chainsaw of domestic and foreign production. The main advantage of such an engine is that the chainsaw motor has a membrane carburetor, which allows it to work in any position. Carbs on all chainsaws work the same.

How to choose wheels for a single tractor? Usually you have to choose from two types of wheels:

• rubber (with deep protectors), which are suitable for moving along a dirt road;
• metal (with soil.spaces) that are designed to work in the field.

The wheels can be selected from any equipment if they are suitable in size.

With the engine from the walk.behind tractor, you can assemble a universal equipment necessary in agriculture. Some add additional equipment to the one.based tractor to perform various work. In this case, homemade allows you to modify the one.axle tractor at its discretion.

Options for composers

The first thing that comes to mind when you think about what you can make from a chainsaw is its use as a sawmill. Many developers had to dissolve logs on a beam with this tool.

Read also: Features of the structure and properties of thermoplastic polymers

Holding the saw on the weight in the hands is very difficult to control the accuracy of the entire length length. Therefore, with three or four.meter logs of the log, it greatly goes away from the intended line. You can solve this problem quite simply. To do this, the chainsaw is rigidly fixed on the frame, which moves along the guide profile.

The log in this case lies motionless and neatly cut along the entire length without wagging and oblique seams. If you provide such a mobile carriage with four lifting screws, then you can accurately set the thickness of the sawn beam.

There will also work without problems on the boots of a chainsaw of a chainsaw, only in this case there will be too many waste, since its cutting chain is several times thicker than a saw of tape sawmill.

Snowmobile

A light homemade championshop from a chainsaw in design is more complicated than a sawmill, since here you need to take gas, clutch, and also take care of the shock.absorbing suspension of the supporting frame.

In addition, it is necessary to develop yourself or use ready.made caterpillar drawings and correctly convey to it from the engine to torque of sufficient power. Since the chainsaw does not have its own transmission, the clutch on such a snowmobile is placed centrifugal with a clinic belt and a chain.

To increase the thrust on the drive shaft of the caterpillar, the “traction” gear is placed, the diameter of which is larger.

There are usually no problems with the steering mechanism, since it is taken from a regular bicycle or scooter and modified so that the central axis moves the rods that turn the skis. The power of the snowmobile engine should be at least 5 horsepower, so for this purpose it is better to use the Ural chainsaw.

The winter line of home.made vehicles will be complemented by a gas pill aerosmi, which are structurally simpler than a snowmobile. The driving force is informed by a large diameter screw that directly rotates the gasoline engine.

A significant restriction for the patency of such a machine is the low power of the chainsaw. Therefore, you can move on them only on the flat surface of rolled snow, the ice of the frozen lake or river. For trips through the fields you will need an engine with a capacity of at least 12 “horses”.

Those homemade inventors who would like to make a ranger.type helicopter from a chainsaw should know the same. Such a machine will need not one, but at least two engines operating in a coordinated mode.

Moped

This vehicle is most often done for the sake of principle, and not for practical use. The main driving force of its creator is the desire to test his strength as a mechanic and prove to others the option of the original use of this cutting tool.

The base for construction usually becomes old grandfather’s chainsaw and no less ancient bicycle, with which you can conduct any experiments to redo the frame for installation of the drive.

Power transmission here is carried out through a gear pair through a bicycle circuit, and the start of such a self.propelled model resembles preparation for cutting firewood.

often there are more advanced models, the base for which is a mountain bike equipped with reliable brakes and shock absorbers. Such a moped made of a chainsaw is equipped with a gearbox with a gear ratio of 18: 1 and variator gear, which allows you to comfortably move on it at the speed of a conventional bicycle.

Boat motor

This option of using a chainsaw is quite simple, since the task is to pass the torque from the saw motor to the rowing screw. A homemade boat motor does not need a transmission setting a transmission. For him, you will need to make a reliable adapter on the lathe from the lead gear of the saw to the rowing shaft. The screw can be used from standard boat motor.

Read also: Types of shuttles in sewing machines

The photograph shows an option in which a gearbox that changes the angle of rotation of the shaft at 90 degrees. In simpler models, they do without it, fixing the engine on the boat so that the shaft is immersed in the water at a slight angle.

Motoculture

It is difficult to make a full.fledged uno.like chainsaw tractor due to a lack of power and traction effort. But the light motor.cultivator on its basis was able to build many home craftsmen.

The design of such a machine is very simple: the motor rotates a couple of gears and transfers an increased traction force to one drive wheel.

Snowman

The chainsaw motor is the same as rotating. a cutting chain or a screw mechanism of a snowman. It all depends only on the design abilities of the Creator and his ingenuity.

Using the Stihl chainsaw with a capacity of about 3 kW, you can easily build a good device for cleaning the area of ​​loose snow. To simplify the design, some masters refuse to install the wheels using conventional sanitary skids.

The most responsible part, on which it depends on how well a home.made snowman can cope with its work is a screw node. The gear pair and chain are driven into its motion. The blades are made of thick cord tires, and the leaf of the sheet of galvanized steel.

Tips and recommendations

On the forums you can find a lot of useful tips, how and what to do correctly when assembling a moped from a chainsaw and great. Fulfillment of simple wishes and parting words from practice will help Amators avoid annoying misses when constructing a moped from a chainsaw.

• Since the improvement of your bike will significantly increase the load on all its nodes, first of all, you should make sure of the excellent condition of the bicycle.
• The engine from the chainsaw after transformations will turn into a home.made cycle motor, so the initial parameters of the engine should be strictly designed: mass. up to 6 kg, volume up to 50 cubic meters. cm.
• In order to avoid fire hazardous situations, carefully test the condition of the fuel tank.
• The transmission of the force on the wheel to the wheel depends on the correct installation and tension of the belt.

Read the same: overview of Champion 251 chainsaws: description, technical characteristics, features of operation

Reviews of the owners

Kolyan:

“Friendship bought an old saw like scrap metal. Replaced the ignition, seals, rings, carburetor. and collected the engine on the new. He took the wheels for the great scooter, and digested a bicycle frame a little. I decided not to put the belts, but a chain gear. Stars 9 and 41 teeth. I did not draw any drawings, so everything somehow turned out to the eye itself. The gas tank from the old moped put. Wheels, of course, small diameter, so the landing turned out low, but it pulls normally.

Disadvantages: not very powerful, low landing “.

Biker:

“It will be useful to install a flashlight and dimensions on a home.made moped, the speed is decent. I made a curtain on a regular bike turnover, you don’t blind the oncoming ones and light your way more ”.

On our site you can also familiarize yourself with the description and reviews of chain saws (battery and gasoline) of these brands: Bosch, Oleo-Mac, EuroLux, Taiga, Interskol, Hitachi, Eco, Forester, Poulan, Daewoo, Hammer, Union, Sturm Parma, bison, Champion, Huter, Echo, Patriot, Ural, Karcher, Carver, Husqvarna, Makita, Friendship, Kruger, Caliber, STIHL, as well as give feedback on the chainsaws of these brands, if you have something to say about the assembly quality and the experience of operating specific models of chain saws of these brands, write in the Комментарии и мнения владельцев your review, it will be very useful for our readers.