Garden gasolimmer how to change a fishing line for a trimmer. Possible malfunctions

How to wind a fishing line for a trimmer for a trimmer for grass: step.by.step guides and video instructions

A beautiful lawn will look truly well-groomed only if you regularly give up grass. For processing complex areas, a trimmer for grass is best suited. Any owner of the unit will sooner or later collide with the solution to the problem, how to wrap a fishing line for a trimmer to a coil, because from incorrect actions you can not only worsen the quality of the mowing, but also disable the equipment. Today in the Homius review, we will talk about all the ways and nuances of the replacement of fishing line and the features of the selection of consumables.

It is convenient to use a trimmer for grass for pumping small or complex areas, for example, near the hedge, between the beds and along the paths. Today, manufacturers produce a wide variety of gasoline, electric and battery models, which can be selected for any requests of the owners.

As a cutting element of a trimmer for grass, a fishing line for a trimmer is used. In the process of work sooner or later, its length will end, and then the owner will arise the question of how to properly replace and fix the thread tucked in the removable coil.

What to consider when choosing a fishing line

Before inserting and fixing the fishing line for a trimmer in a removable coil of a trimmer for grass, it is important to choose the right material.

Rating of the best models of gasoline trimmer for grass. Review of manufacturers and models, as well as useful tips from experts considered in this review, will help in a difficult choice among many models of devices.

By quality

Before you put a fishing line for a trimmer on a trimmer for grass, you need to pay attention to the cross section of the cord:

• Round cross.sections are the most common option. They perfectly give way to grass even in complex areas;
• A line for a trimmer with a spiral section is suitable for thin grass. It is not very durable and is not suitable for old thickets;
• The cord with zabrinki and sharp faces is chosen for mating by weeds;
• A fishing line for a trimmer with a variety of geometric sections will help to mow the lawn more evenly, but the strength of the consumable material is low.

Important! The most wear.resistant consumables are a two.component fishing line for a trimmer with a round section, enhanced from the inside.

The owner of Motokosi should know that it is categorically impossible to use metal wire, fishing thread and a variety of strings.

Rating of the best electric trimmers for grass. In this review, we will analyze the criteria for choosing an electrochemmer, technical characteristics, as well as the most popular models and brands according to consumer reviews.

In size

Before winding the thread, you should pay attention to its size to the coil of the trimmer for the grass. Most often use a fishing line for a trim with a cross section of 2 mm.

You can choose the right diameter in the following ways:

• View recommendations in the manufacturer’s instructions for trimmer.
• Often manufacturers apply information about the cross.section to the bobbin.
• The cross section of the cord should be suitable for the diameter of the coil opening.

Important! The thicker the thread will be seasoned, the more rigid grass it will be able to mow.

What is needed to replace the cord

With regular use of a trimmer for grass for begging grass, the discs are blunting, but they can be sharpened and continued to operate. The fishing line for a trimmer in the coil has the ability to end, so there is a need for refueling a new one, for which you need to determine the type of head and prepare the cord of the required thickness and length.

So, the mowing head is a cylindrical body in which a bastard is placed with a fishing line. Such a part is present both on electrimmers and on gasoline braids of any brands, whether it be Bosch, Makita, Stihl or other brand. There are three types of heads depending on the method of refueling and feeding the fishing line.

• The principle of operation of the heads of the automatic group is that they independently serve a fishing line for a trimmer, when a mowing reduces the speed of the motor. Such designs are convenient when working in large areas, but they have a shortage. a large cord consumption.
• The heads of the semi.automatic group are easy to operate. automatic fishing is performed at maximum engine speeds. To remove the cord lock, you need to carefully tap on the ground with the tool, after which the unlocked thread extends from the coil. The cut to the required length is made with a knife fixed on the protective casing.
• Trammers for grass with manual supply of the cord must first be turned off, and then independently pull out the fishing line for the trimmer.

On a note! The most convenient and optimal in price are semi.automatic coils with the cord.

Coils for electric and gasoline braids can be with one or two tastes of fishing line. The former are used to trim low herbal shoots, the latter. for beveling tall grass and small shrubs.

Preparation for the replacement of fishing line

Before replacing the fishing line, you need to pull out, and then disassemble the head. It usually includes a casing, a spring (on some models), a bobbin with a fishing line, a lid. It is necessary to turn off the electric trimmer for the grass (or drown out gasoline) from the network, and then proceed to remove the coil. It can be recorded in two different ways: in the first case, it is necessary to completely disassemble the head, and in the second. just remove the gearbox from the shaft, to which it is attached.

• A bobbin is located under the lid, it must be carefully pulled out of the case (sometimes a spring is hidden under it, it should also be carefully removed to the side so as not to lose);
• After removing the spool, it becomes noticeable in the center of the case with a fixing bolt (or screw), which must be unscrewed in a direction opposite to the clockwise movement;
• After removing the fasteners, it is necessary to hold the body with a swaying movement to remove the coil from the gear shaft.

Now that the head is removed and dismantled, it is necessary to determine what thickness the cord should be. You can find out the suitable diameter for your trimmer for the grass by looking at the user’s guide or on the squash itself, it usually indicates such information. Another way is to insert the thread into the hole from which it is served. If the Sruna is without difficulty, it can be used to work.

On a note! To understand how much fishing line is wrapped for coil, you need to wind it on the bobbin so that the height of the skein is not more than the diameter of the sides. If the cord protrudes behind the edges, the coil cannot be hidden in the casing.

Garden Trimmer

A light and convenient trimmer for grass for removing grass, and even without a odorous fuel or an annoying electric cord clinging to everything that can be for which. You can mow vegetation even in the most inaccessible places, for example, near the fence, border or around the trees.

Powerful electric motor

Cope with dry grass and large weeds

Telescopic pen

will reach the most uncomfortable places

Protective shield

protect the face and eyes from flying garbage

Garden Trimmer Effective and economical

Compare a trimmer for grass for Garden Trimmer grass with more expensive and uncomfortable benzotrimers

Garden Trimmer

• Price: 1590 rub
• Compact and light
• Does not require skills in circulation
• Small
• Safe
• Works from cheap batteries aa

Benzotrimmer

• Price: from 8000r
• Heavy and inconvenient
• Requires skills in circulation
• Very noisy
• Traumatic
• Additional expenses for gasoline and oil

“Great thing for pumping grass”

Powerful enough with its slight weight. What is important to me. a motor in a very durable case; You can work on wet grass and are not afraid that the trimmer for the grass will burn. A great thing for pumping grass along the fence on the site and between the trees. Dry grass and dandelions pumps out quickly and efficiently. You can safely work with a fishing line in a vertical plane.

“There were no breakdowns for two seasons of operation”

Powerful trimmer for grass. I have been using it in the village for 2 years, until I failed. The grass is also out of the overgrown, but the trimmer for the grass does perfectly, the grass does not wound on a fishing line for a trimmer. For two seasons of operation there were no breakdowns. A trimmer for grass is perfect where it is necessary to mow grass not only in the country, small areas, but also in the adjacent territories.

Peculiarities

If you read the features of the models of this manufacturer, then to begin with, it should be said that this company from Germany was based on one thousand nine hundred 70 nine years. All the equipment that is produced under this brand is created by qualified engineers and developers and is being verified at every step of creation. In general, the lawn mowers of this German company are massive and fairly productive models. Their use allows you to cut grass in almost all criteria. Very often the best models of this company are used specifically for professional purposes. One of the fundamental features characteristic of all models of the manufacturer will be that motor.coats from Huter are equipped with a two.stroke engine with air cooling and electric ignition. This function makes it possible to ensure the highest power of the device and high.quality execution of the intended target.

Before the introduction of a gasoline trimmer for grass, its owners must make sure that the gearbox is lubricant. In addition to using this device correctly, you should read all the norms that contains the operating abstract. There are also safety standards here, advice on the abilities and techniques of effective work, as well as proper maintenance motorcycles.

Read how much a mixture for a benzotrimer is stored

When the user got acquainted with all this, he can have a lawn mower and start the installation of the device. It should be carried out during the first 3-4 hours of operation. At this time, you should very carefully operate the motorcycle. This is the most perfect in sparing mode on a soft grass. Under no circumstances can it use it in idle for more than 10 minutes. These periods should certainly be alternated with interruptions and gangways for 20-30 seconds. During this period, adjusting and setting up the working modes of a gasoline trimmer for grass. It will not be unnecessary to have a spare fishing line for a trimmer, so that in the event of damage or unsatisfactory operation the standard one can change the fishing line for a trimmer to a more benign.

Preliminary preparation

At first, for winding the fishing line, it is necessary to remove the coil (bobbin, spool) from a trimmer for grass. Certain acts will depend on the difficulty of configuration and the type of product itself:

• Small electronic trimmers for grass with workers placing a motor and coils at the bottom, usually have side buttons on both sides of the bobbin. With the simultaneous press on their highest part of the coil, coupled with the internal contents for winding the fishing line is disconnected, while the lower one remains on a trimmer for the grass. The analysis of the bobbin is better to create in an even smooth place, so that the spring does not jump out and not be lost;
• Electronic and gasoline trimmers for grass with a curved rod without the ability to install a knife, usually have coils with special lamb: in similar structures, you should with one hand with one hand to hold the rogue in an exclusively position, and the other counterclockwise to twist the bobbin on the barc. After disconnecting the nut, the whole bobin is removed.
• Electronic and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and with unhurried rotation, such mutual placement is achieved when the screwdriver enters the holes and the bobin is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third options of coil, depending on the design, are versed in different methods. In the bobbins, lambs turn out from the lamb, in the coils from the latch, the fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then they are quite turned with their hands in the back sides until they are completely developed.

The final moment of the instruction

Typically, the process of replacing fishing line on a trimmer of a particular model is popularly described by accompanying documentation. Another question is that this documentation is often supplied in a foreign language, since the notorious lawn mowers for the most part are imported products.

Meanwhile, there is a much simpler, more economical and healthy way for human health and nature. putting the lawns of an ordinary peasant oblique in order. Blory of braids for grass:

which is subsequently accompanied by abundantly growing greens, and not by the formation of dryness as a result of the work of a trimmer for grass.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

• Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
• Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
• Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

• The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
• One end of the fishing line is inserted into the fixing technological hole located inside the spool.
• The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
• A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
• The left end of the fishing line is passed through the hole of the outer part of the bobbin.
• Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

What can be used instead of fishing line

Many users of trimmers are wondering: how to replace the cord, by default used in this kind of devices? Unsafe experiments begin to carry out, installing metal or copper wire, metal cables or strings in a mowing head, as well as a regular fishing fishing line for a trimmer.

If you install a metal cable instead of fishing line, then a trimmer for grass turns into a dangerous device not only for the user, but also for others. This fact is explained by the fact that during the operation of the unit, the steel cable will be gradually shut up, its ends are gradually released, and small pieces of wire will fly in different directions at high speed.

And if you accidentally hook your or someone’s leg, working as an unit with a steel cable (wire), then a strong and deep section of the fabrics, and in some cases, amputation of the fingers are provided with you. The manufacturer is not in vain for these purposes, nylon uses, since it is quite light and durable, and when separating he does not fly away and cannot cause injury.

It is possible to use a fishing fishing line for a trimmer in a trimmer instead of a standard one, of course, but this will add unnecessary trouble, because it quickly wears out, breaks, mows slowly and does not fit for cutting hard grass. In addition, during the work, a lot of time is lost to replace the broken tool more than once.

In practice, the installation of a regular fishing line is justified if the user is going to mow grass near the fence, especially if he is from a rabid grid. In this case, in order to protect the standard and sometimes expensive cord from wear, it changes to a fishing fishing line for a trimmer, which is not a pity. Usually, in order to change the cord to a fishing line for a trimmer, it must be selected the greatest thickness-2-3 mm.

Selection by models

The cord spontaneously lengthens

There are situations when a user of a trimmer for grass notices a very fast fishing line consumption. At the same time, he never hit the ground with a button to lengthen the fishing line. The reason that the fishing line for a trimmer spontaneously lengthens, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, forget to install a clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

Trimmer for Huter grass, fishing line replacement, Garden head

Also, a fishing line for a trimmer can lengthen without using a button if the spring is weakened. If the spring check confirmed this fact, then it is necessary to put several goals under it to strengthen its clamping properties.

Semi.automatic coils and how effective they are

The most popular among mowers are trimmers for semi.automatic grass. From the name it is clear that the fishing line for a trimmer exits the coil in a semi.automatic mode. For this, the head is equipped with a mechanism through which the fishing line is submitted. Kosarya for supplying the cord must be touched by the lower part of the earth’s head in order to bring the mechanism into effect. This is very convenient, since it is not required to jam the tool motor and stop the grass of the grass.

Lengthening of the cord is carried out due to centrifugal forces. Working with a tool with a head semiautomatic device is very easy and convenient. Many masters recommend using this particular option, but do not indicate the following information:

• If you plan to use semi.automatic coils, then exclusively branded models
• Buying cheap devices is irrational, as they do not serve even several months
• Rationally buy a semi.automatic type, which are designed directly for a specific brand and a model of a trimmer for grass, since universal are often distinguished by low assembly quality

Based on the foregoing, it should be noted that it is far from always rational to buy coils for trimmers of a semi.automatic type, especially if there are models more perfect and no less reliable. automatic.

The master is a master

For work, we will need:

First of all, it is necessary to give the shape of a circle to our future pendant. To do this, just wrap a thick wire around a jar and bite off excess material in the right places with nippers.

We form the holder of the pendant, as indicated in the photo.

Now it is necessary to beat off the circle so that it becomes flat and bend the holder, thereby forming an ear through which you can miss a chain or lace.

We wrap the wire, form the roots of the tree as indicated in the photo.

We form the crown of the tree as indicated in the photo, string the stone baby. We fix the branches along the edge of the round base very carefully so that the edges of our pendant look neat and there are no gaps between the rings of the winding.

Another option for making a pendant. There are fewer twigs, and instead of stone crumbs, beads are used, which is distributed closer to the rim of the pendant.

How to change a fishing line for a trimmer on a lawn mower: detailed instructions

In 1971, American entrepreneur George Bollas invented a mower for grass, where a fishing line for a trimmer played the role of a cutting knife. A lot of time has passed since then, the drive has become more powerful, a modern trimmer can easily damage the bark, so that the idea itself was transformed into mowing around obstacles without damage to the very cutting apparatus of a mowing room. For a neat mowing around obstacles, you can have a head with a smaller fishing line, it is easy to change it when moving from mowing large areas to delicate blocking. However, periodically and the cutting tool itself requires replacement. We tell you how to disassemble the head of the lawn mower (trimmer for grass) and wind a new fishing line for a trimmer.

All about the replacement of fishing line with a trimmer head

There are many types of heads that are designed for different types of fishing line. The latter is also available in several diameters: from 1.0 mm to 3.2 mm. At the same time, its section is round (including with a special groove to reduce noise), square, twisted and in the shape of a star.

There are no clear preferences, and this explains the wide variety of forms and diameters in the market. The round shape is usually stronger, but has a worst cutting ability, in addition, when rotation, it makes a characteristic sound. Therefore, sometimes they make an acoustic groove, however, the use of this fishing line makes sense only on battery trimmers, in machines with gasoline and network drive, the sound level of the drive itself practically drowses the sound from the fishing line. The square has a good cutting ability, and despite the fact that such a fishing line for a trimmer is less durable than round, on average it is consumed less. A square fishing line for a trimmer quite easily cuts the shoots of the same Ivnyak up to 1 cm in diameter. The star has the maximum number of cutting faces, mows best and is the fastest consumed.

The next nuance when choosing is stiffness. The fact is that in the production of nylon, a modifier (often maleine anhydride) is added to it, which improves its strength and prevents gaps. However, modifiers are not the cheapest component, they are trying to save on it. Therefore, it seems to be a good fishing line for a trimmer that remained for the winter, in the spring suddenly behaves completely differently. it breaks, stops doing normally from the reel. There is a recommendation to soak a fishing line for a trimmer in the water before work, but I do not see much sense in this, malein anhydride interacts with water, but if it is not enough in the nylon, then there will be nothing to interact. Therefore, it makes no sense to stock up on fishing line for a long period of time, a breakdown or constantly torn fishing line for a trimmer, which also does not want to leave the reel itself, can significantly complicate the work.

How to wind a fishing line for a trimmer to a trimmer coil for grass

First determine the length of the consumable for your reel. Wrap a fishing line for a trimmer on a bobbin until it staches for the sides. We got 4 meters. How much will it work with you depends on what diameter of the fishing line for a trimmer for a spool and design features.

Winding algorithm

Lay the fishing line for the trimmer in accordance with the indicated direction on the element case.

Insert the short end into the groove on the side of the coil.

Fasten the long end in the opposite groove.

Place the coil with a wound fishing line in the spray building.

Cut the ends of the fishing line, leaving 10 to 15 centimeters.

The replacement of the fishing line is completed and now it remains only to fasten the bobbin on the trimmer for the grass and you can work.

ATTENTION! Typical problems with fishing line

No wonder they say: “”Forewarned is forearmed“”. Knowing the possible problems and causes of occurrence, one can prevent them in a timely manner. We recommend remembering or leaving a memo.

For a better understanding of the mechanism of the process of replacing fishing line in a spool with video assistance prepared by Fubag specialists: