Gasoline for the gas mower StiHL What gasoline to fill. Fuel consumption

Motokos oil. how to choose in what proportions to breed

Most often, when preparing fuel for the work of saw, 1:50 and 1:40 are used to work. This means that one part of the oil is added to 50 or 40 parts of gasoline. Calculations are made as follows: 1 l = 1000 ml, 1000/50 = 20 ml or 1000/40 = 25 ml, that is, in the first case, pour 20 ml into each liter of gasoline, and in the second. 25 ml of oil. If there is no instructions and you do not know the proportion to prepare the mixture, then use the following recommendations:

• Tool and oil of one brand. For example, for the Stihl chainsaw, the ratio of gasoline and STIHL oil will be the same as indicated on the container with oil, usually 1:50.
• The substances used for the mixture have different brands. the proportion of 1:40 is selected.
• There is one brand, but there is no information about the ratio of substances on the oil. they are divorced 1:40.
• In the absence of any data on the saw and oil, the mixture is bred in a proportion of 1:40. The only thing you need to make sure that the oil is intended for two.stroke engines.

To carry out the run.in a new saw at the first three gas stations with fuel oil, add 20% more. In this case, instead of a ratio of 1:50, it will be 1:42, and the proportion 1:40 turns at 1:33. 24 or 33 ml of oil, respectively, will require a liter of gasoline. Other countless events with a new saw do not conduct. Manufacturers advise working only at the largest speeds always. After the instrument run, the usual proportions are used 1:50 or 1:40. In some cases, the manufacturer of the equipment also indicates other ratios, for example, 1:25 or 1:32, they must be observed.

We make a mixture: important proportions

Using a two.stroke engine, unsented fuel is purchased separately and mixed with oil, often in 1:50 proportions. In such a engine, it is constructively unrealistic to install an oil pump, so pouring unsuccessful gasoline into a chainsaw is strictly prohibited! The manufacturer shows the proportions, quantity and certain brands in the operating annotation.

What oil to choose for refueling in a trimmer for grass or types of lubricants

Trammers for grass and lawn mowers operate on two.stroke engines that have a simplified design. Rarely, but there are models of trimmers with 4-stroke engines that work on pure gasoline. Two.stroke.type power units do not have a compartment for pouring motor oil (oil crankcase), due to which the weight of the tool is reduced and their cost is reduced. If the rotating details of the motor are not lubricated, then in the end they will quickly fail. To prevent this, a trimmer for grass is seasoned not with clean gasoline, but a mixture with butter. What kind of oil to dilute with gasoline for a trimmer for grass?

First, remember or find out what types of oils are produced by chemical composition:

• Mineral fluids. designed for small power technology, which has air cooling. This is the cheapest type of lubricant for motors
• Semi.synthetic substances. they are used for technology, which has air and water cooling
• Synthetic. suitable for all types of motors with different types of cooling. They do not require frequent replacement, and this type of lubricant is several times more expensive than mineral and semi.synthetic

From the foregoing it follows that for a trimmer for grass, oil with any composition is suitable. mineral water, synthetics and semi.synthetics. Oils with different chemical composition differs in price, so it is necessary to rely when buying on the recommendations of the tool manufacturer. The instructions indicate recommendation information about which types of oils are best used. If this is the TS-W3 standard, then it is not so important which composition should have a substance. In this case, you can dilute mineral water, semi.synthetics and synthetics with gasoline.

It is interesting!The main thing when choosing oil is not to fall on the fake, since today you can very often find different types of lubricants for two.stroke engines, which consist mainly of low.quality oil products.

Комментарии и мнения владельцев 49

Log in or register to write Комментарии и мнения владельцев, ask questions and participate in the discussion.

Unine.based tractor “Mole” I feed 92. Although 76 used to digest well. For 15 years I have never prepared for wintering. Similarly, with a saw and a trimmer. Our country season ends very sharply and unexpectedly, and therefore I can’t prepare. Today, last year’s mixture of liters is 5, everything starts up and works.

Lying for many years good 92.If 2-stroke, then gasoline with butter (it is desirable to strictly pour without overflows and short-legged oil-this is harmful). I pour the mixture only to work. You can’t leave. The mixture does not get drunk for a long time. It is better to bring in small portions to work. If there is not much left, I drain.For the winter. an empty tank only.

In 4-tact, I leave a little gasoline in the winter. But I block the supply of gasoline to the carburetor and wait until it develops the rest.

Oil in a 4-stroke motor block I change every spring before starting work.

The experience is still small, only one winter. All last season, and that has begun this is 92 gasoline. Champion oil of a Chinese manufacturer. Then I will switch to “Shtlevskoye”. I read the forums. to preserve for the winter or not. I talked with my grandfathers from the forestry, they said do not score your brain. Finished the season, put the whole tool into the garage. I tucked it in the spring, and drove I tried it. everything is fine, I started it easily.

Do not leave the main thing in the winter, and indeed with a mixture in the tank. Empty and let him modify the rest. The mixture is oxidized quickly.STIHL used. Pontent Dear. Better gasoline 92 normal.

I leave 5 years as there is gasoline and leave it and leave ! The braid for grass and chainsaws work with half a turn

Lew 100 from Lukoil) The pancake began to mow itself))) Of course, 92 Husqvarna oil, I don’t drain Benz for the winter, but I pour a new one before the season, I do not do more than two liters of the mixture.to say benz with butter for a long time nizya!

I keep with benz, then I fill in the new 92, and I change the candle in the season, it leads with half

The mixture is stored no more than 5 days.Then it breaks down and you can’t use it. It is necessary to produce for 5 days. Mix conveniently in 5-liter bottles. If you need little mixture, then in the Stilevskaya special bottle of a liter-item in a nose-starter for oil.Cosha himself with a parapier and pour 92 but 5 years poured 95 and everything is fine. For the winter, conservation with a complete drain of fuel and filling in a cylinder of a teaspoon of two.stroke oil is necessarily. And pull the starter several times.

Why is it not to be used after 5 days suddenly? And what is it split into? On atoms or something! In childhood, Bati in a motorcycle, of course, split overnight, to an almost empty tank. And now what suddenly? There will be no Ioi still something else to start?

Split. this is a modern myth of dick quality. If you remember in childhood, Bati/grandfather Moped “Riga” only did not pour there and it went. And right now.- 5 years keep then split, for the winter.

Then my gasoline is some kind of wrong, since the technique starts with gasoline month ago!

I’m talking about the fact that they go for the ears. From last year everything has been flooded and in the spring. chainsaw, drill, lawn mower. I don’t drain anything if it remains.

Split. this is a modern myth of dick quality. If you remember in childhood, Bati/grandfather Moped “Riga” only did not pour there and it went. And right now.- 5 years keep then split, for the winter.

For the time being. The piston does not wear out immediately. Can ride but it’s better not to take risks. The technique is expensive and I want to save it. An analogy with Soviet motorcycles is interesting and touching. My Carpathians were also refueling. But with Japanese scooters and Canadian snowmobiles this will not pass, upper. I don’t want to try. Also with high.tech lawn.cocked equipment. Here is a bottle. Prepare the mixture-minute. Everything is thought out. Is it really so difficult to follow the recommendations?

Preparation of the correct fuel mixture

Before starting to run the new engine of the lawn mower, you must also prepare the fuel mixture correctly. As you know for two.stroke engines, it is prepared from special two.stroke oil and gasoline, taken in certain ratios. You can find out proportions from the instructions attached to the tool, or on the labeling label. From the instructions you will also learn the recommended type of fuel, as well as the recommended type of motor oil.

Cook fuel in small quantities sufficient for one mowing grass. Use special canists made of plastic for fuel, or a separate glass or metal dishes. It is best to type oil with a medical syringe.

Having gathered to run into a new lawn mower, many are faced with the problem in the preparation of the fuel mixture. And the reason for this is the disagreement in the instructions of the tool manufacturer and in the instructions of the manufacturer of motor oils. The first recommend a 1:25 proportion. The latter recommend 1:50. Who to believe? How to proceed?

According to experts, if in the instructions for a motorcycle, manufacturers write a proportion of 1:25 or 1:30, then it is most likely a cheap tool with poor cooling, or the manufacturer does not know what kind of oil will be added to the consumer. But here it must be understood that the excess of lubricant does not affect the performance of a trimmer for grass in the best way. Excess oil does not completely burn out when operating the engine. It cokes, clogs a cylinder and piston.

What to do in this situation when running in a new tool? An ideal option would be to purchase exactly the oil that the manufacturer of the lawn mower recommends. In the case of run.in engines, when it is not possible to purchase the recommended oil, it is best to purchase a good Husqvarna two.stroke oil for the same gas tool. It costs not cheap, but there is enough it for a long time. It is necessary to interfere with it as it is written in the instructions on the bank.

Remember, it is best to use the proportion that the oil manufacturer gives. But is that proportion that is written on a spit is better to find out by experiment. If, with a trimmer recommended by the manufacturer for grass, the proportion of the engine sniffs with oil and the subteids are visible on it, then the proportion must be increased.

What oil to choose for refueling in a trimmer for grass or types of lubricants

Trammers for grass and lawn mowers operate on two.stroke engines that have a simplified design. Rarely, but there are models of trimmers with 4-stroke engines that work on pure gasoline. Two.stroke.type power units do not have a compartment for pouring motor oil (oil crankcase), due to which the weight of the tool is reduced and their cost is reduced. If the rotating details of the motor are not lubricated, then in the end they will quickly fail. To prevent this, a trimmer for grass is seasoned not with clean gasoline, but a mixture with butter. What kind of oil to dilute with gasoline for a trimmer for grass?

First, remember or find out what types of oils are produced by chemical composition:

• Mineral fluids. designed for small power technology, which has air cooling. This is the cheapest type of lubricant for motors
• Semi.synthetic substances. they are used for technology, which has air and water cooling
• Synthetic. suitable for all types of motors with different types of cooling. They do not require frequent replacement, and this type of lubricant is several times more expensive than mineral and semi.synthetic

It is interesting!The main thing when choosing oil is not to fall on the fake, since today you can very often find different types of lubricants for two.stroke engines, which consist mainly of low.quality oil products.

How to dilute gasoline with oil for a trimmer for grass

Dilute gasoline for a trimmer for grass in the correct proportion. Insufficient oil can lead to poor lubrication of the elements of the lawn mower, which contributes to rapid wear. In case the oil is more than the olive formed on the pistons and spark plugs. Foreths on the moving parts of the engine interferes with normal operation and leads to the speedy breakdown of the motor.

What proportion is required for a specific model of a trimmer for grass can be found from the attached instructions. Most often, for 2-stroke gasoline motors of motorcycles, the fuel mixture is used in a ratio of 50: 1, where 50 is part of the gasoline, 1-part of the oil. That is, 20 ml of oil should be added to 1 liter of gasoline. The table will help to choose the necessary ratio.

To correctly measure the proportions, use measured containers with a milliliter scale. For these purposes, a special canister with a double neck is perfect, it is designed to mix and storage of oilbenzin. For example, oil can be typed with a medical syringe without a needle. Before mixing liquids, make sure that there is no water, dust and particles of dirt in the container for the finished fuel mixture.

Diluting gasoline with lubricating fluid directly in the fuel tank is unacceptable, in addition, the proportion of oil and gasoline should be clearly observed. If you ignore this rule, then the operation of a trimmer engine for grass can be unstable, which is why it will quickly fail.

It is not recommended to use plastic bottles or canists for this purpose. This is due to the fact that gasoline has the ability to dissolve plastic, which means that part of the plastic can get into the fuel tank, which can lead to a carburetor breakdown. Although there are special plastic canists with the marking “Flame”.

• petrol;
• oil suitable for two.stroke engines with an air cooling system;
• canister, better metal;
• Mixing container is also better metal;
• gloves;
• respirator.

In addition to protective equipment, do not forget about fire safety rules, because gasoline and engine oil are easily ignited:

• It is better to work on the street to avoid accumulation of gasoline vapor in the room;
• you can not smoke and create situations related to the emergence of a spark.

Make a mixture of gasoline and oil as follows:

• Pour 1 liter of gasoline into the container, add half the desired portion of the oil. Mix thoroughly, do it extremely carefully away from the sources of open fire.
• Add the rest of the oil to gas for the grass and mix thoroughly again. Now fuel can be poured into the fuel tank of a trimmer for grass.

The mixture can be stored for no more than three months, so it is better to dilute gasoline in such quantities that there is enough use.

For dilution, only high.quality oil can be used, while it is recommended to purchase it only in trusted stores, for example in specialized hypermarkets.

Obtaining a mixture

How much oil is pouring per liter to get high.quality gasoline mixture? It would seem that there is nothing complicated in mixing two substances. The preparation of the mixture is often complicated by the fact that in various sources, various information is indicated. For example, the instructions indicate the proportion of 1 to 40, on the fuel tank of the trimmer for grass 1 to 25, and on the canister with oil 1 to 50.

Most experts are sure that it is necessary to mix in accordance with the instructions indicated on the packaging with oil.

There are a number of requirements for how to dilute. Do not add too much oil. This leads to a decrease in ignition characteristics. As a result, the devaluation of the efficiency of the power unit occurs, and the general decrease in its resource. In case of oversaturation of gasoline mixture with oil, soot sediments (ventilation windows of the cylinder) will form on the inner surface of the walls of the engine. This is fraught with the formation of a nap on the piston.

Neither oil starvation, nor excess lubricant on a gasoline basis are a good basis for prolonged ICE operation. For a trouble.free prolonged operation, the same number of components is necessary. Breeding is best done using the same measured tools to exclude unnecessary errors.

How to calculate, let’s say how much oil is pouring per 1 liter of gasoline with a required ratio of 1 to 50? To do this, we transfer the volume of gasoline into milliliters 1l = 1000 ml. Accordingly, to achieve a ratio of 1 to 50 thousand, they are divided into fifty. Only 20 g of oil will need one liter of gasoline. Someone measures the oil with a 20 cubic syringe, but for such purposes there is a special measured spoon, which sometimes comes with oil from some manufacturers.

For ease of calculating the ratio of oil and gasoline, we bring the table https: // cmetnik.ru/oil/

Benzotrimmer loves cleanliness. It is necessary to monitor the purity of the air filter and fuel. It is better to defend gasoline bought at a gas station for 2 days and pass through the simplest filter. a piece of bike matter.

We check the electrical equipment as follows:

We unscrew the candle, examine the gap between the electrodes. We set the right gap between the electrodes can be a “grandfather” way. We take a blade from a razor, scraps in half and insert a home.made probe between the electrodes. If the blades enter tightly, then the gap is perfect.

We put on a candle cap of a high.voltage wire and lean the candle against the metal surface of the engine. Twist several times by the starter. If the spark beats well at one point, then the gap is adjusted correctly. If not, the spark is weak or “wanders”, then it is necessary to re.adjust the gap between the electrodes.

With each sharpening and removing the chain, the tire is turned over for uniform wear on both sides. This is especially important for domestic chainsaws. Professionals work with a saw and in the upper and lower position, ordinary users. mainly in the lower. Therefore, the tire wears out faster, it has to be changed more often.

Never pour a car and waste oil into an oil tank. What does this lead to:

We recommend using only special oil. Thanks to viscosity, the oil remains on the chain, tire, and also falls into additional slots on the chain. this provides the best lubrication. 1 liter packaging is enough for 8 gas stations. These are about 20 sessions of 15 minutes of continuous sawing.

What gasoline to use

At gas stations, you can find fuel of different types. Each of them has its own cost and technical characteristics, including special additives in gasoline. However, not every brand is suitable for a chainsaw. In order not to spoil the equipment and provide optimal work, it is necessary to fill in fuel above 92. Some experts note that due to poor quality, combustible materials, instead of 92, 95 should be used.

Another rule of the proportion of oil and gasoline for the chainsaw is associated with ethyled fuel. Choosing this type of fuel is strictly prohibited, since it increases the failure of the engine and its components.

How often should you change the oil?

Do not recommend for lawn mowers to purchase low.quality compositions. Poorly peeled or not laid the grade of oil and gasoline do not affect the condition of the engine. It will have to be washed, but not always such a procedure will help restore the operability of the motor, may also need major repairs.

You need not only to know how to replace the oil, but also when to perform this procedure. Too frequent change is not needed. in vain spending of money, and a rare increase in engine wear. In the technical instructions of each model, the optimal frequency of oil change is spelled out, as well as tips regarding the most suitable brands. If this is not spelled out, then you need to follow the general recommendations. From the new motor, which is running out, the oil is drained and poured after about 5-6 mothers. Then the procedure is repeated several times with a break after 5-10 hours of functioning of the lawn mower.

Stihl FS 130 Motokos device

The Stihl FS 130 lawn mower is released with a balanced design, as well as a good selection of components. The base equipment of the grass trimmer includes a 2-stroke 1-cylinder ICE company, developed under the 4-MIX system. It significantly reduces the consumption of fuel by forced combustion of the entire volume of fuel. At the same time, the Stihl FS 130 lawn mower is emitting fewer harmful emissions, and it works much quieter than other similar models.

To start the engine in the device of braids for grass, a modified manual starter is provided, which, due to the built.in automatic decompression, is released by less resistance when the cable is pulled. To facilitate the launch of the motor in winter, the manufacturer has equipped a trimmer for grass with a manual pump for preliminary pumping of fuel.

The STIHL 130 trimmer is equipped with an adjustable bicycle handle made of stainless steel. Both structural handles are covered with anti.slip rubberized material that improves the capture and increase the accuracy when working with the tool. The power button and the ignition lock, as well as the gas trigger, are put on the right handle of the motorcycle. This simplifies the operation of the model when working in conditions of limited space.

Internal details and mechanisms of braids for grass are protected by a plastic case, free access where it makes it possible to quickly replace worn spare parts. The wide neck of the fuel tank allows you to fill the required amount of the fuel mixture without spilling fuel.

Refueling safety precautions:

Depending on the construction of the chainsaw, the gas processing process may vary.

Using a special device:

Good to know

Fuel blank should be made by counting on 3 gas stations. After all, storage of a large volume of fuel can adversely affect the work of a chainsaw. The mixture can behave differently, because many factors will affect it. As a result, your household unit can get a serious breakdown, which will entail financial costs.

Sometimes even a container can affect the quality of the liquid. Plastic and glass react with gasoline, which can create a danger of sudden ignition.

It is important to remember that in case of a breakdown of the chainsaw due to poor.quality or incorrect mixture, it will not be possible to repair the unit under the warranty.

Ready fluid cannot be stored for more than a month, because the process of oxidation occurs. After working with a chainsaw, you need to use the remaining fuel, turn off the engine and remove the remaining fuel mixture.

Preparation for carburetor adjustment

The primary importance when setting all the characteristics of the dosage of the fuel of the STIHL 250 model is the highest adjustment screw located near the muffler. The factory setting, the parameters of which are shown on the upper plastic cover, provides that it should be twisted one revolution from a complete twist.

DIREHL 250 with your own hands is adjusted throughout the operation process. Writing the screw enriches the working mixture, since the air-fuel mixture receives a larger volume of gasoline, and tightening the screw impoverishes the working mixture, since the air fuel mixture receives less gasoline.

Adjusting the carburetor will not give positive results if there is an air leak on the engine side through:

Settling STIHL 250 carburetor is set up only after a careful inspection, identifying the existing air leaks. The next step in preparatory adjustment work is the full maintenance of all components and mechanisms.

• cleaning from deposits, slag, resins;
• engine washing using a solvent, acetone;
• replacement of the spark plug;
• cleaning, air filter washing;
• Checking the tension of the cutting circuit;
• idle setting;
• warming up the engine to operating temperature.

Then you can proceed to complex settings manipulations.

Adjustment of the carburetor of the chainsaw STIHL 250

Step.by.step adjustment of the STIHL carburetor MS 250 with a revolution meter is carried out in the following sequence:

• Drown out the engine, the screws h and l should be twisted to the stop, then turn both on one revolution.
• Engine start, warm. At maximum revolutions, the screw of the maximum frequency of the crankshaft 14000 rpm, fixed by a tachometer or engine speed meter. Keep the maximum engine speed no more than 10 seconds.
• Bolt LA stop the idle speed to achieve the start of the chain. After that, turn La Bolt ¼ turn counterclockwise.
• Check the acceleration of the Stihl 250 chainsaw mechanism. The adjustment of the carburetor continues if the idle speed is unstable or the chainsaw is not accelerated enough. Screw L must slightly turn counterclockwise. At the same time, the saw should quickly gain momentum, operate steadily at idle. Finally adjust the work of the La screw. By the tachometer, the idle stroke should correspond to the catalog value of 2800 rpm.

Similarly, the Carburetor of the Stihl 211 chainsaw is adjusted with your own hands.

In his article, the author highlighted all the details of adjustment to all the familiar German production mechanism called the STIHL 250 saw. Carburetor adjustment is simple and accessible to every home master. Constructing the recommendations set forth by the author of the article, everyone can configure their Stihl 250 chainsaw and enjoy its impeccable work.

STIHL MS180 Basil Basil. We make a mixture. Secrets and tricks. Lifehack

The fuel mixture of gasoline and oil is prepared in serious observance of the tips of the manufacturer. For stihl chainsaws, you are 1:50, in other words, 1 l of AI-92 gasoline must be added 20 g of oil.

To measure the amount of oil, of course, at least with some methods-a syringe or some kind of measured dishes. However, more comfortable in the process of use are bottles with a dispenser in which STIHL oils are produced.

So that the stihl chainsaw works productively within a long period, you need to adhere to subsequent tips:

• Gasoline is fresh, and not from the canister of month ago.
• It is forbidden to use oils for 4-stroke engines. It will not burn one hundred percent, which will lead to the formation of soot and the rapid wear of the cylinder-piston group (CPG).
• In a 2-a-point engine, the oil should burn without residues, therefore it is more advisable to use synthetics. which is characterized by the formation of the smallest amount of burning and smoke residues.
• When breeding a consistency, it is better to add not just the recommended volume of oil, but within reasonable boundaries. 5 g of excess per 1 liter of gasoline will not lead to a hair clipping. may be a prerequisite for the formation of soot and breakdown of CPG. On the contrary, pour 5 grams less than the designated, this is fraught with overheating piston and cylinder.
• It is not recommended to use the cooked mixture of monthly ago.
• It is forbidden to use oils for mopeds. they are not created for a chainsaw, because they are designed for the smallest number of revolutions.
• After the season, the mixture must be used to the mixture in other words to drain in order to avoid the loss of gasoline parameters, as well as wear of the seals.

Chips on the choice

Now let’s try to figure out how to choose high.quality oil for trimmers, which works on gasoline. The main feature to direct attention to. This is a basic number. This moment eliminates the oxidation of the parts in which friction is observed, and very slows down their deformation. The more this compound is used, the faster it loses alkalinity and becomes more oxidized. The best acidity (pH). This value is the least 8-9 units.

The second fundamental factor, which also seriously affects the performance of a gasoline trimmer for grass, is the viscosity of the oil. This feature determines the possibility of using the device at different temperatures. Summer grades of oils begin to thicken at the least temperature difference.

The third point, the importance of which should not be underestimated. This is a flash point. This indicator should be more than two hundred 20 5 degrees. In an unpleasant case, the composition will burn very rapidly and the load on the piston group will begin to increase, which will lead to its accelerated wear. Also, a 4-stroke oil will not be for 2 strokes. Namely, the last type of engine is used in the vast majority of gas mowers.

If we are talking about manufacturers, then you can make a small rating that will allow you to focus on the recipes offered by different manufacturers. For example, STIHL offers high.quality synthetic and mineral oils that have already proven themselves as a good solution in at least some time of the year.

This is considered a very good Shell Helix Ultra Oil. Specialists note its highest properties and good characteristics of alkalinity and viscosity. Apart from that, the products of such brands as Oleo-Mac, Motul, Hammerflex, Echo. If we are talking about the products of domestic brands, then the LUKOIL oil should be paid attention to this. Its price is several times lower than foreign analogues, but at the same time has high quality and good technical characteristics.