How can you cut the foam along. Determine the length of the nichrome thread

Than and how to cut foams at home: review of methods and stages

Engaged in assembling kitchen stools, I thought why not make sitting soft. But in order to create such a kind of upholstery, I faced the question of how to cut foams very exactly at home. Indeed, for the finish covering of the seat, you need to be able to correctly cut the fragment in accordance with the size. In this post I will tell in detail about the process.

Furniture manufacturers use special machines. You can cut polyurethane foam of any thickness, with a perfectly flat seam and accurately observing the size.

Naturally, these options are not entirely suitable for home: especially when you need to cut a couple of sheets to restore furniture and never do it again.

In such cases, it is recommended to use the so.called “loaf” (with zazubins on the blade). Its shape and length allows you to make an even section of thick polyurethane foam. It will have to be cut for a long time, but as a “one.time action” the method is quite suitable.

Please note: in no case do not listen to the advice of the “craftsmen” and do not cut the foam rubber with a wire (tungsten or nichrome). Heating foams leads to the release of phosgen. toxic gas. It is extremely dangerous to inhale it in a closed room.

Drawing up a project

For example, we have determined that a double.sized shredder with a low rotor rotation frequency is suitable for production tasks.

His project necessarily includes:

engine selection by power;
calculation of the gear ratio of the gearbox and the choice of the factory model;
determination of the diameter and length of the rotors (according to the size of the loading window);
calculation of shafts for strength;
The choice of bearing supports.

For this you will need the textbook “Parts of cars” for universities. You will also have to look into GOSTs according to threaded connections, reference books on gearboxes, bearings, couplings and other assembly units.

This must be taken into account when you assign the dimensions of the groove.

After calculations, it is necessary to make a layout of nodes on a millimeter paper or in an AutoCAD type editor, determine the dimensions of corps parts and beds.

This task must be approached responsibly so as not to miss anything. Sometimes the protruding head of the “unaccounted” bolt leads to the fact that the car has to be redone. After that, a detail is made. the drawing of each part separately.

Foam: why is it called that

The Poliuretan Poliuretan owes its name to the Scandinavian company Porolon, which was the supplier of the material in the USSR. Therefore, foam, polyurethane or PPU is the same material.

A special mixture of polyol, water, isocyanate and other components is taken for foam rubber. Cells of different sizes are obtained due to different proportions of the ingredients used. Further, all components are mixed in a special container. For foaming foams, a special block form is used, into which a mixture of components is poured after mixing. After the process ends, the manufacturer moves the foaming unit into a separate room per day. Further, foam blocks are ready for cutting sheets of the required thickness.

How to round the foam rubber

In order to equally round the angles of the PPU equally, it is necessary to make a template in advance. Then its contours should be transferred to a leaf of polyurethane foam, and with the help of a clerical knife to make a neat even rounding. It is important to keep the knife in an upright position. It is best to choose a tool with a long blade or a special saw. An ideal fishing line for a cutting trimmer will turn out when using a special tool or machine. Therefore, it is better to order a large number of details from specialists.

When heated to a critical temperature (255 degrees Celsius), the foamine first begins to melt, then lights up. During the combustion process, light smoke stands out and an inconspicuous flame appears. There are non.combustible stamps of foam.

How to carefully cut off and glue furniture foam at home

Foam. universal material. It is used in many large industries and in needlework. Differs in a porous structure, elasticity, softness and attractive cost. When working with Furniture Furniture in domestic craftsmen, especially those who did not use it before, two questions arise: how to carefully cut and firmly glue the details from this material among themselves. The secrets of how to do this correctly, quickly and reliably shared the masters of Vinyl Text.

To cut evenly and without a bully foam furniture for a sofa, chair, ottoman or armchairs, stock up:

A sharp knife: stationery or for cutting linoleum;
marker or felt.tip pen;
thick cardboard, plywood or a piece of board under the base;
wooden rail or ordinary ruler, pattern (for curved cuts).
Select a place for laying out a sheet of foam and put a thick cardboard or a piece of board under the material so that when cutting, do not spoil the base (floor, countertop);
Make a pitch or marker with a felt.tip pen or marker and connect them using a rail or ruler. For a cut under the radius, use a template or pattern;
Take the knife and, holding it strictly vertically, with a strong, confident movement, spend on marking. Do not use the ruler when cutting, since it will put pressure on the foam rubber under the weight of the hand, crush it, and the cut will eventually turn out to be uneven;
If the foam rubber does not cut through to the end, spread your fingers with the “processed” site and bring the work to the end to the end. When the bullying appears, break the blade of the clerical knife or replace it.

Than and how to glue foam

Contact adhesives are suitable for working with foam rubber on butadiene-stirol, polyurethane, non-reprevable basis. The most popular and budgetary of them are: BF-6, glue 88, Rapid-100. They are safe for health (do not exude toxins), easy to use and reliably fasten the foam parts among themselves.

Lubricate the edges of the prepared parts with glue using a roller, brush or spray gun. Economy option. a gun, the consumption of the composition is about 70 grams./cm.sq.;
Wash the time specified in the instructions;
Connect the details, pressing tightly or pressing the press, until a reliable, even, elastic seam is formed.

Vinyl Text company: Furniture foam for a sofa and other upholstered furniture, as well as upholstery materials, accessories to retail, wholesale and delivery to all regions of tools for cutting foam

So, how to cut foams at home, so that the edges are as smooth and close to what is obtained during production cutting? To do this, you will need to prepare the following tools and consumables:

Actually, the foam itself, which we are going to cut.
Lining for foam rubber we will cut. It’s clear that if we decompose it on linoleum or on the floor of the apartment, these very materials will end, since they will all be in scratches from the knife. In the role of lining, it is best to use a sheet of plywood with a cardboard laid on it, so that the tip of the knife does not dull about the hard plywood. Cardboard can be used by dismissing any cardboard box of a suitable size.
It is advisable to have a knife from the category of construction. They are also called knives for cutting linoleum. He includes a whole clip of removable blades, which in the event of a gear can be changed. It is better to use a branded European rather than a Chinese knife, since the steel of the “Chinese” is low.quality, and such a blade will dull after the first wiring.

How to cut smoothly thick foam at home?

However, at home, this is not recommended, since foam rubber distinguishes harmful substances into the air, which, even in small doses, are highly toxic and affect the respiratory and nervous systems of a person. We will not risk health, especially since foam rubber is well cut by an ordinary knife.

Mark a piece of foam rubber with a marker or felt.tip pen, while putting small marks. Combine the tags together in a ruler (you can use a flat bar).

Under the place of the future cut, put a piece of boards, plywood, wood-boring plate or just dense cardboard. This will protect the floor from damage during cutting.

Making a Hotwire Foam Cutter (Warning: Risky & Dangerous Method)

Cutting foam is recommended without a ruler. Spit with a strong and accurate movement with a knife according to the marking you made. At the same time, hold the knife vertically.

If the foam rubber does not cut through to the end, spread the cut part with your fingers and cut the foam to the end with the second reeza.

If the cutting is obtained, this means that the knife blade has become dull. Break the tip of the blade or replace it with a new.

Curved cuts are made according to exactly the same technology. Mark the pattern, then cut the foam along the line, making sure that the knife does not fill up, but is located vertically. The quality of the cut will not be perfect, but it will be quite fit if you need to cut out a pillow for upholstered furniture, which will then be covered with fabric.

Pre.soaked thin foam is much easier to cut with scissors.

How to carefully cut off and glue furniture foam at home

To cut evenly and without a bully foam furniture for a sofa, chair, ottoman or armchairs, stock up:

A sharp knife: stationery or for cutting linoleum;
marker or felt.tip pen;
thick cardboard, plywood or a piece of board under the base;
wooden rail or ordinary ruler, pattern (for curved cuts).
Select a place for laying out a sheet of foam and put a thick cardboard or a piece of board under the material so that when cutting, do not spoil the base (floor, countertop);
Make a pitch or marker with a felt.tip pen or marker and connect them using a rail or ruler. For a cut under the radius, use a template or pattern;
Take the knife and, holding it strictly vertically, with a strong, confident movement, spend on marking. Do not use the ruler when cutting, since it will put pressure on the foam rubber under the weight of the hand, crush it, and the cut will eventually turn out to be uneven;
If the foam rubber does not cut through to the end, spread your fingers with the “processed” site and bring the work to the end to the end. When the bullying appears, break the blade of the clerical knife or replace it.

Lubricate the edges of the prepared parts with glue using a roller, brush or spray gun. Economy option. a gun, the consumption of the composition is about 70 grams./cm.sq.;
Wash the time specified in the instructions;
Connect the details, pressing tightly or pressing the press, until a reliable, even, elastic seam is formed.

Furniture foam for the sofa and other upholstered furniture, as well as upholstery materials, accessories in retail, wholesale and delivery to all regions for cutting

If you follow all the instructions, your foam will be perfectly cut. So, let’s begin:

Since we decided to cut the foam on the lining, and not on linoleum or parquet, first we put it. First plywood, then a sheet of cardboard.
We put a layer of foam rubber on top that we want to cut. We ensure that the fishing line for the trimmer of the future section falls on the lining.
We take a ruler and, according to the indicated dimensions, we carry out a fishing line for a trimmer along which the future cut will take place.
Remove the ruler. If you cut along the ruler and at the same time press on it, the cut will turn out even, but the edge will be as pressed as in scissors. If you decide to cut along the ruler, in no case do not press on it.
We take the knife, adjust the blade to the desired length and make a small incision on one side. Many people wonder how to cut thick foam rubber so that it is even from the edge, and not from the original cut. In fact, there is no difference in the thickness of the foam itself. The main thing after the first incision is to insert a knife into the initial fishing line for the trimmer of the incision and make the first full incision, slightly with a free hand by both edges of the cut foam on both sides of the knife. Then cut will be perfect.
In many articles, consultants advise always to keep the knife in an upright position. They copy each other, not understanding each other. Do not listen to idiotic councils. And vice versa, the knife should be kept at an angle to yourself. This plane of the knife blade should always be vertical in relation to the ground. It can not be distorted either to the right or to the left, otherwise the edge on the cut will come out trapezoidal.
Of course, the first incision will not cut the foam to the end. Patience. This is fine. Distribute the edges of the cut, insert the knife and make another even incision. In the end, the tip of the knife will creak on the cardboard, and the task will be completed.

Good advice, how to cut foam rubber so that the edge is perfect. If you feel that the knife began to make peculiar hooks during wiring, then, in some place the blade was dull and, without cutting, begins to tear the foam rubber, forming a strip of foam rubble. In this case, immediately replace the blade with a new. It is best to do this without waiting for this to happen. Made five to six threads, changed the blade. After that, they can be reused for any other purposes, but they will no longer be suitable for cutting foam. This video clearly shows a simple cut of foaming with a knife.

How and what to cut thick foam at home?

Poliuretan foam. modern material of synthetic origin. At home, cutting foam rubber is quite easy: you only need to outline a fishing line for a trimmer along which the canvas will be cut, with a knife with a sharp blade and cut the canvas to the end, slightly holding the edges with the second hand.

How to cut foams if the thickness of the canvas is 10 mm or more? If you adhere to the rules for cutting foam, then you can achieve an even edge of the material even at home.

How to cut foam rubber?

There is no need to buy a specialized saw for polyurethane foam, which is used in stores or in small industries to cut a sheet of foam at home.

It is enough to use a sharp knife, you can take a knife with a zazubins with which a loaf is cut. Thanks to its shape and length, the material is even. If there is no such knife, then any other well.sharpened knife is suitable. If you have a construction knife with a advanced blade, then it is also suitable for cutting foam.

The secret of the even edge of the material is a knife tilt during cutting, if you need to make a flat fishing line for a trimmer. Когда требуется фигурная резка поролона, угол наклона следует увеличить. This will avoid beads at the edges.

Stages of cutting foam

To cut the canvas PPU does not require expensive tools or special conditions. In order to cut the canvas at home, it is necessary to stock up on a sheet of cardboard and plywood, a ruler or curly pattern (if the fishing line is uneven), a marker or construction tape, as well as a sharp knife. The whole process consists of simple stages:

You need to choose a flat surface where you will cut the foam.
Put the plywood and cardboard on the surface of the floor or table so as not to damage it with a knife while cutting the material.
Using a line with a marker or construction tape, note a fishing line for a trimmer of the alleged cut. Scotch tape is suitable for a flat line, and for a figure. a marker.
The ruler can be held by the material while cutting the sheet into parts. Do not press too much on the ruler, as this can lead to deformation of the canvas, and the edge in the site of the cut will turn out to be uneven.
You can use two slats made of wood, when it comes to cutting on a flat line. Between the strips should be left for the cut. This will fix the sheet.
Cut the canvas with a strong and smooth movement of the knife. If the first time it does not work out to cut a thick material, then it is necessary to repeat the procedure by inserting the knife exactly into the fishing line for the trimmer of the already made section. You can first make a cut to half the thickness, and then continue cutting until the end.
Figure cutting of thick material with a knife is more difficult, so you need to keep the knife at a large angle on yourself, and lead a knife more carefully.

To make the incision even, you need to buy high quality foam. Our store presents material from the best manufacturers. The assortment has sheets of different thicknesses and density. To choose and buy a suitable foam for your task, call our store by phone indicated on the site.

How to cut foams

Hello everyone, just recently I had a problem, how to cut off the foam rubber evenly, and at home. For all the time of passion for carpentry, I have never encountered foam rubber, it is understandable, I usually work with woods.

Since cut off foam? And what you need to do. The first thing that came to my mind was some kind of expensive machine that it is simply not realistic to buy, since I once cut a foam, but for a very long time, and I didn’t really succeed.

At work, in the next workshop, they are engaged in upholstered furniture, and somehow, at lunchtime, I met a guy who is engaged in this Street. During the conversation, I found out that in order to cut off foam, they use the knife, and they have no expensive equipment for this. We talked and he told me how to cut off foam gently at home.

To cut off foam rubber will need the following

A sharp knife, best is the chancellery or for cutting linoleum
A felt.tip pen or a marker with a thin rod
Cardboard or something else for the base
Good ruler

So, how to cut off foam rubber, first using a marker, make the cut line on foam. If these are straight lines, it is better to use the ruler, if you should have a cut under the radius, it is better to use some kind of pattern, template or other device in order to draw exactly the radius.

Next, to cut off foam, it will be necessary to prepare the base. As a basis, many advise you to use a plywood or a wood-piece plate. I would not advise you, because when you cut a foam rubberle with a knife, the tip of the knife will dull about this plywood. Therefore, for the ground, I advise you to use cardboard. By the way, I forgot to say why the base is needed, the base serves so that the floor or another base does not spoil, on which you are going to cut off the foam rubber, well, and as you understood for protecting the tip of the knife.

Well, the last point how to cut off foam, this is the process of cutting. To do this, take a very sharp knife. Your kitchen knife is clearly not suitable here, since his blade is thicker. Therefore, I advise you to use a stationery knife, or a construction knife, like those that cut linoleum. It is very important that the blade and the tip are sharp, otherwise you can’t get a foam rubber.

Well, then go to work, spend exactly along the line with a knife, preferably without using the stop, since the emphasis will be pressed on foam, thereby creating a load in it, and the knife will be poorly cut. If you doubt your abilities, it is better to practice a little on another piece of foam rubber so as not to spoil the workpiece.

Anyway, foam rubber is usually cut in order to sheathe up her upholstered furniture. Therefore, you can not do perfectly evenly, and you can’t get 100% exactly cut off exactly. The fabric will still be on top of the foam, which will smooth out all the irregularities and errors of the cut.

Here I am an article, it may be useful for those who have thought about cutting off foam at home with your own hands. I will be glad to Комментарии и мнения владельцев, tell us what you think about it, and if there is experience, share it.

Often you can find advice that foam rubber should be cut with a heated nichrome wire connected to a voltage of 12 V, as well as a heated soldering iron.

How to cut smoothly thick foam at home?

Mark a piece of foam rubber with a marker or felt.tip pen, while putting small marks. Combine the tags together in a ruler (you can use a flat bar).

Under the place of the future cut, put a piece of boards, plywood, wood-boring plate or just dense cardboard. This will protect the floor from damage during cutting.

Cutting foam is recommended without a ruler. Spit with a strong and accurate movement with a knife according to the marking you made. At the same time, hold the knife vertically.

If the foam rubber does not cut through to the end, spread the cut part with your fingers and cut the foam to the end with the second reeza.

If the cutting is obtained, this means that the knife blade has become dull. Break the tip of the blade or replace it with a new.

Curved cuts are made according to exactly the same technology. Mark the pattern, then cut the foam along the line, making sure that the knife does not fill up, but is located vertically. The quality of the cut will not be perfect, but it will be quite fit if you need to cut out a pillow for upholstered furniture, which will then be covered with fabric.

Pre.soaked thin foam is much easier to cut with scissors.

How to cut foams?

It would seem that the question? Take it and cut. There are no problems with a material up to 5 cm thick.

Than cutting exactly thick foam?

But how to make an even section of a 10-centimeter or even thicker foam?

In the vastness of Internet forums, advisers are actively offering pretty bold ways. For example, heated tungsten or nichrome wire. over, the craftsmen are advised by connecting the wire to electricity with a voltage of 12 V. Choose, they say, the temperature so that it does not burn, but cut. Here right here. Stop! Porolon-Optom store.RU considers it his duty to warn that this method of cutting polyurethane foam materials, and especially at home, is dangerous to human health. The chemical reaction between heated wire and foam rubber is accompanied. With normal contact of foam rubber with fire, this will not happen, the material is not fuel and environmentally safe. But chemical experiments of self.taught that have not read the textbook on chemistry should not become an example to follow.

How to cut smoothly thick foam at home?

Mark a piece of foam rubber with a marker or felt.tip pen, while putting small marks. Combine the tags together in a ruler (you can use a flat bar).

Under the place of the future cut, put a piece of boards, plywood, wood-boring plate or just dense cardboard. This will protect the floor from damage during cutting.

Cutting foam is recommended without a ruler. Spit with a strong and accurate movement with a knife according to the marking you made. At the same time, hold the knife vertically.

If the foam rubber does not cut through to the end, spread the cut part with your fingers and cut the foam to the end with the second reeza.

HOW TO CUT THE SQUARE BOTTLE. Cool homemade bottles

If the cutting is obtained, this means that the knife blade has become dull. Break the tip of the blade or replace it with a new.

Pre.soaked thin foam is much easier to cut with scissors.

How to cut foams?

It would seem that the question? Take it and cut. There are no problems with a material up to 5 cm thick.

But how to make an even section of a 10-centimeter or even thicker foam?

There are special knives for cutting foam. The secret of obtaining a flat cut in such porous materials as spongy rubber or polyurethane foam, in very thin and sharp blades and special movements that these blades make. In electrical goods stores, you can purchase an electronics for cutting foam. Devices look usually like this.

On an industrial scale, these are already entire electric machines. Here you can, as they say, write out the most bizarre forms and lines. To fix the sheet or cube of foam rubber in industrial installations, vacuum is used.

The machines most often have a strip knife for cutting foam.

A very thin blade and a special location of the zabrinki, as well as a stable continuous force that can be obtained from the machine, allow you to get an even smooth cut.

However, master-taught masters are not behind. On one of the forums for the so.called dummies, the luminaries demonstrate a wonderful alternative to the electronics for foam.

A device of two aluminum rails and a sharply sharpened knife can save the situation when it comes to one or two pieces of foam rubber, which must be cut out at home. True, the knife will not need the usual, with a serrey sharpening. This is a special, wavy type of sharpening, which is often used by hunters. However, and culinary knives for cutting hot loaves have a similar look. Such a artisanal invention is not at all scary to try to do it independently, at least it will not threaten health problems. And who knows, maybe you will become the next innovator who will show the world the next hypostasis of the most popular material of the 21st century?

If you want to save your time and effort and get foam crumbs or a cut of foam rubber, you can contact us by phone 7 (495) 978-33-44. Always in stock at affordable prices!

⚡ gluing and cutting foam. how and how to cut foam

Polyurethane foam. material with a porous structure, high elasticity, soft and inexpensive. It is most often used to fill mattresses and as furniture stuffing. If there is a desire to pull the furniture or make a mattress with your own hands, there is a problem: how to cut foams at home and how to glue it? There are several recommendations for craftsmen.

To cut foam and make its edges extremely even, it is necessary to stock up on special tools and consumables. Among them:

lining. it will help protect the surface from scratches that occur during cutting. A plywood sheet supplemented with cardboard is suitable (a cardboard box will fit in a laid out state);

Building knife or other knife with a long blade. Additionally, buy a set of removable blades to easily change them after wear. Remember that high.quality knife is the key to the success of cutting foam. So buy models of the average price segment;

If you need a figured cutting, you need a cardboard template with a cut pattern;

marker. with it, you can outline a fishing line for a trimmer cut.

How to cut furniture foam: instruction

If all the materials and tools are at hand, you can proceed directly to the process. Compliance with cutting technology will achieve an ideal result. How easy it is to cut foam. complete instruction:

Put the plywood, wood-fiber plate on a flat surface (for example, floor), and place a sheet of cardboard on top of it on top of it.

Lay the foam plaster on top of the cardboard so that the place of the future section is on the cardboard and does not go beyond its edges.

Using the ruler, draw a fishing line for a trimmer along which you need to make a cut. Cutting can be made under a ruler if the length of the knife blade allows.

Having taken the knife, configure the required length of the blade. Then make a small incision on one side. After insert the knife into the starting fishing line for the trimmer of the cut and make confident accurate movement. The second hand at this moment slightly grab the edges of the foam block. Cutting foam at an angle is the best solution that allows you to make a cut as even as possible.

We also have different stamps of foam rubber on sale. Everything is available at a store in Kyiv. Look into our catalog of foam. you are sure you will find a suitable for you. We will provide an exhaustive consultation on the choice of foam.

If the first cutter turned out to the entire width, it is necessary to gently expand the edges of the cut, deepen the knife and make the last cut. As soon as you hear the rattle of the knife blade on the cardboard, it means that you coped with the task.

DIY foam cutting is a difficult task, but real. To make the edge extremely even, it is necessary to use a knife with a very sharp and long blade. If the knife began to cling or began to tear the foam. it is time to replace the blade or undermine it. But it is better not to wait until the last, but immediately take care of the timely replacement.

Curly cutting foam is no different from the straight line. But the angle of inclination towards itself must be maximally increased, otherwise the cut parts will have a little oblique edges. There is nothing complicated in such cutting, the main thing is to stock up on patience and high.quality knife. Also for curly cutting, you can use a special saw for foaming Bosch GSG-300 Professional.

It is such a foaming saw that is in our arsenal and we can easily cut the sheets of foam rubber for you 30 cm thick. The quality of the cut is wonderful, everything turns out perfectly evenly and perpendicular. Cut the figures of various shapes a rather entertaining and interesting activity.

You can order the cutting and gluing of foam rubber on our website by going to the card of the services that interests you. The cost of cutting is indicated for the linear meter, and gluing. per square.

Dismantling the riser

It is necessary to follow the rules when separating the vertical sewage pipe:

Management services are notified, permit for repair work is issued;
Users of the riser living above along the floor are notified;
Repair operations are carried out.

The presence of a compensator allows you to shift the product in one direction or another up to 10 cm. It must be remembered that the vertical design has a certain mass. Therefore, it needs to be fixed.

The joints of the joints are processed with machine oil. When performing rotational-setting movements, the part is removed from the overall structure. The absence of a compensator forces to resort to radical methods. to cut the fan pipe.

PVC plastic sewer pipes are processed by most locksmith tools:

Mechanized device. angular grinder, saber saw.

When carrying out work, it is required to pay attention to the presence of a number of other communications elements:

The compounds of sewer pipes that have served 10 years or more can “grab”, “grow” to each other. Help in such cases a number of recommendations;

Processing the junction of the WD-40 lubricant;
wrap sandpaper around the pipe; make rotational movements through it. hands will not slip, circular effort will increase;
If the product is scrapped, then it is necessary to make a through hole across the part; By inserting a tube or a metal rod, we get a lever;
Apply a “barbaric” dismantling method. cut the pipe into pieces, break into pieces.

Methods for separation of PVC pipes used to arrange an external highway, exactly the same. But, it is necessary to determine the place of damage and perform excavation work.

How and what methods of unlocking pipes. choose the owner of the housing or invited specialists. The main thing is to determine the feasibility of a particular way of dismantling faulty details.

Well, something, and there was a lot of cast iron in the Soviet Union! All technologies were developed taking into account this material. So in the laying of sewage, Chugun is still very popular. Of course, cast iron has many very significant advantages. it withstands heavy loads, which allows you to collect risers on many floors, it is durable, can fulfill its function in raw or cold rooms for decades, the paint lies well on the cast.iron pipe, that is, it can be beautifully entered In design. In a word, a sewer pipe made of cast iron is a thorough, durable thing. But in this thoroughness lies its main drawback. To disassemble, if necessary, part of such a pipeline is very difficult. And this is sometimes an acute need. For example, you needed an additional discharge or the existing discharge has become unusable. What to do?

Best. when a professional is performed, a master of his craft. In this case, you can be sure of the quality and efficiency of the work done. But this option is not always possible. Often plumbing should wait for weeks, and their prices, to put it mildly, are inflated. It happens that this “master” has no experience in such works. Not all those who wears the plumbing of the plumbing are such, are such.

Manufacturing of the machine site

The machine site will consist of a countertop (desktop) and four legs. We make them from plywood 12 mm thick. The size of the countertop according to the drawing of the master is 30×31 cm.

We saw off the workpieces of the required size, after which we process them on a grinding machine or using a grinder. The edges of the countertop should be slightly twisted so that they do not catch the workpiece.

We attach the legs to the countertop on a scythe. To do this, the author dries at an angle of two holes with a diameter of 4 mm, then a 10 mm drill will need to expand the holes along the screw hat.

We also recommend reading an article-review: how to make a conductor with a fixer for compounds with a slanting screw. Such a device in the workshop will definitely not be superfluous.

Next, mark and drill the fasteners to connect the legs with each other using plywood segments. We mark the attachment points of the legs, retreating a certain distance from the edge of the site.

Sources:

https://weldingmaterials.ru/rezka/kak-rezat-porolon.html
https://intstyle.com.ua/polezno-znat/vse-o-porolone-otveti-na-voprosi
https://oblavka.ru/blog/kak-akkuratno-otrezat-i-skleit-mebelnyj-porolon-v-domashnih-usloviyah.html
https://nkolip.ru/svoimi-rukami/kak-sdelat-porolon/
https://101benzopila.ru/kak-rezat-porolon-v-domasnih-usloviah/
https://veloelektro.ru/kak-rezat-porolon-v-domashnih-usloviyah.html
https://stroyvolga.ru/%D0%BA%D0%B0%D0%BA-%D1%80%D0%B5%D0%B7%D0%B0%D1%82%D1%8C-%D0%BF%D0%BE%D1%80%D0%BE%D0%BB%D0%BE%D0%BD/
https://intstyle.com.ua/polezno-znat/poklejka-i-porezka-porolona-kak-i-chem-porezat-porolon
https://weldingmaterials.ru/rezka/kak-rezat-porolon.html

Articles determine, foam, length, nichrome