How To Cut Plastic Panels

Panel gluing options

There are different options for how to glue plastic panels. Each master has his own glue, tested over the years, and yet there is a wide selection in this area, but how to glue PVC panels? The main options are described below:

Emficol 34012A. This glue is specially designed for attaching PVC, as it has good adhesion to plastic.
Kleyberite 636. It is created on the basis of synthetic resin, therefore it is environmentally friendly.
Moment Crystal. This glue is used to adhere to almost any surface.
Liquid nails 601. This is a universal adhesive for interior work.
Liquid nails 901. Glue that is used both for indoor and outdoor work. It is able to securely attach even heavy materials.
915 Liquid Nails. an adhesive specially used for gluing PVC tiles and tiles in bathrooms.

Table. Main characteristics of different adhesives

Advantages Disadvantages

Emficol 34012A	Strength, viscosity, resistance to temperature changes, lack of color.
Clayberite 636	Affordable price, moisture resistance, fast drying.
Moment Crystal	High degree of adhesion, durability, lack of color, resistance to moisture and temperature extremes.	High price.
Liquid nails 601	Durability.	Lack of moisture resistance.
Liquid nails 901	Moisture resistance, versatility, strength, durability.
Liquid nails 915	Resistant to moisture and high temperatures (specially for bathrooms).	Opaque but light in color.

Pasting walls with PVC panels

Recently, plastic panels have become popular finishing materials. Their use allows you to make a beautiful finish in a short time.

A variety of textures, colors and sizes attracts those who want to create a unique design of the room. They are used to decorate kitchens and balconies, and their resistance to moisture makes the use of plastic panels simply indispensable for pasting bathroom walls.

Knowing how to glue plastic panels to the wall will allow you to successfully install this decorative material.

Adhesive requirements

Most often, plastic panels are used to finish the bathroom. This means that the adhesive used must be securely attached even in high humidity conditions.

Choose an adhesive with high adhesion and fast tack

Required characteristics for glue:

Moisture resistance. Since the humidity in the bathroom is high, the glue for gluing can only be used from moisture resistant brands;
High degree of adhesion. This is necessary to ensure better adhesion to the wall;
Resistance to different temperatures and their drops. The use of panels in a bathroom, where temperature and humidity tend to change rapidly, is possible only if they are securely attached to the wall surface;
The presence of antibacterial properties. A humid and warm environment is ideal for bacteria and fungus to thrive. In view of this, the adhesive for wall panels must be antibacterial;
Durability. Although the panels can be glued with almost any glue, in order for them to be securely fixed for many years, a high-quality composition is needed;
Fast "stickiness". It is necessary that within 10 minutes after gluing the panel to the wall, it was already firmly fixed;
Lack of a high level of toxicity and pungent odor;
Transparency.

Plastic panel fastening technology

Although it may seem that the installation of PVC panels is a difficult task, in fact, following simple instructions, all work can be done by hand and without the involvement of specialists.

Some people prefer to attach such material to a pre-assembled frame, but this reduces the area of the room. But how to glue PVC panels and can wallpaper be glued to plastic panels? Further, the technology of fastening with glue is described step by step.

The walls are cleaned of the old coating: wallpaper, paint, etc.
The surface is leveled, if necessary, putty. This stage is very important, since the final result depends on the evenness of the surface. In the process of gluing, the bumps and pits cannot be smoothed out, and this will affect the quality of gluing.
Then the walls are primed and left to dry completely.
The panels are brought into the room and left there for at least 12 hours. During this time, they acclimatize.
The material is cut to the desired height of the room.
The glue is applied pointwise or dotted. The panels can be glued starting from the corner or door by pressing firmly against the wall.
Upon completion of installation, all glue residues are removed.

As you can see, work on gluing plastic panels and corners can be done independently. First you need to decide on the glue on which this material will be attached. For an overview of adhesives for PVC panels, see this useful:

For bathroom furnishings, one good option is to use 915 Liquid Nails, which are specially formulated to work in wet areas. Before the installation itself, it is important to make sure that the walls are even, because the appearance of the room after the installation of the panels depends on this.

Cutter

Experienced craftsmen rarely face the problem of how to cut PVC wall panels, because in their arsenal of tools there will definitely be a special cutter. This tool is able to make an absolutely even cut on the panel, while a minimum of physical effort is required from a person. Craftsmen can try to make a similar tool on their own, following the instructions.

How to make a cutter with your own hands?

Take a strip of metal at least 2 mm thick and 1 cm wide.
Cut one edge of the metal strip at an angle of 45 degrees.
Sharpen your homemade cutter using a grindstone.
Wrap the opposite side with electrical tape. this will protect your hand from damage during work.

Stationery knife

A regular utility knife can also be used for this purpose. First, an even cut is made on the surface of the panel along a ruler, after which the plastic simply breaks.

Hacksaw

A hacksaw is a versatile tool that any craftsman can find. If there is no opportunity to purchase a special cutter, but you do not want to do it yourself, then the wall plastic panels can be cut with a hacksaw. With this tool, cutting will take a little more time, but if the amount of work is small, then this fact will not significantly affect the duration of wall cladding.

How to cut plastic panels with a hacksaw? When sawing PVC panels, some nuances should be taken into account:

For sawing plastic panels, you must use a tool for wood with fine teeth (transverse dusting) or for metal.
In order not to damage the material during the cutting process, you do not need to apply strong forces.
Saw at a slight angle from the front.
Several panels can be cut at the same time. To do this, they are stacked.

How to cut plastic panels

How to cut plastic panels at home? This question is very relevant for budget-conscious homeowners who decide to sheathe the walls of the toilet and bathroom with decorative PVC panels. The material is practical and may well replace ceramic tiles when there is a lack of time or funds for a full repair. In this article, we will find out how to cut plastic panels so as not to damage the material and make a neat edge.

The better to cut plastic panels?

Plastic panels have been loved by the owners of apartments and private houses for a long time, because their installation can be done independently without much difficulty, they do not lend themselves to the influence of moisture, belong to materials of low flammability, are resistant to mechanical damage, and also have a long service life and are relatively cheap.

However, it is often necessary to cut the panel, because its standard length is 3 m, which often exceeds the standard ceiling height in high-rise buildings and private buildings. In this regard, inexperienced craftsmen are faced with the question of how to cut PVC panels. In fact, there are several answers. Let’s consider each suitable option in detail.

Power tool

For the most impatient, the answer to the question of how to cut plastic PVC panels will be a power tool. Any machine that is at hand can be used. This method will save time, because the cut will be carried out in a matter of seconds.

So, what is the best way to cut PVC? For this, they most often use:

Angle grinder (angle grinder).

How to cut plastic PVC panels

Plastic panels have a number of advantages that make them an indispensable material for quick and inexpensive renovation of bathrooms, toilets, loggias and garden houses. The panels are impervious to moisture, are low-combustible materials, resistant to mechanical abrasion, have a long service life and are relatively cheap. They can decorate both walls and ceilings. The technology of mounting plastic panels is simple and does not require preliminary surface preparation.

One of the essential stages in the installation of plastic panels is their cutting to the required size. The complexity of this stage depends on the condition of the surface to be finished: if the wall, for example, is straight and even, then you can prepare the entire volume of plastic panels required for it in advance. If the wall has different heights, complex shapes or includes architectural elements (windows, doors, ledges, etc.), then you will have to cut the panels along the way, which, of course, significantly increases the installation time.

How to cut pvc panels. How are plastic panels cut? Tools and rules of work

Quite often, in residential apartments and offices, you can find wall and ceiling decoration with plastic panels. And this is not at all surprising, because this material is quite inexpensive, good in operation and retains an excellent appearance for a long time. And the work is incredibly simple. Even a person who works with him for the first time is unlikely to have difficulties.

You can also use a simple knife, only having previously sharpened it as best as possible. Although this is not the best solution, or rather, the most unfortunate one. After all, the cutting method is not suitable for cutting panels. But still, this tool will eventually also cope with the task.

It is convenient to cut the panel with a stationery knife. To begin with, an incision is made along the mowing line from above, and then the material breaks.

Or you can make a knife yourself: cut it from a piece of cast rolled steel at an angle of 45 degrees on one side and sharpen it, and wrap the handle with electrical tape to make it convenient to hold.

But it is more convenient and reliable to purchase a special construction knife. Among all the answers to the question of what plastic panels are cut, the last one is the most suitable.

If a saw is used for wood, then the teeth should be for transverse or mixed sawing, and preferably undiluted, then the plastic will be cut neatly and evenly. Therefore, a saw is not the worst answer to the question of what plastic panels are cut with.

An angle grinder is a good option for working with panels. But there is one important nuance: you need to work extremely carefully with this tool, because plastic is an incredibly fragile material and there is a possibility that it will break. After cutting the angle grinder, you need to grind the corners with a special machine. If it is not found in construction equipment, it is better to look for another way.

How to cut plastic panels? 4 tools to choose from to help

When covering the surface of PVC, it is required to decide in advance and decide how to cut the plastic panels. Currently, as a decoration for a bathroom or bAL-KO, this material is practically out of competition and is very, very popular.

Someone may object and remember at least a tile, as one of the most traditional finishing materials for bathrooms. Yes, tiles are a classic and a tradition. But PVC is mounted easier and faster, requires much less maintenance, since it does not collect soap and precipitation from the water, in case of damage it can be easily replaced. In a word, tiles are still inferior to the first positions to plastic panels. And if you need to quickly and efficiently sheathe services, now many choose exactly the panels.

First of all, they fell in love with the people for the availability of independent installation. It causes the only difficulty: the standard plank length of 3 meters is too large for most apartments. In addition, the height of the ceilings can vary. both due to errors of the builders, and due to the flight of the owner’s design thought. So the finishing material needs to be shortened, which means it must be trimmed.

How to cut plastic panels. It has been invented for a long time. And these methods. both folk and modern technological ones. are diverse enough for us to choose: either the method that seems more convenient, or the one for which there is a suitable tool on the shelf. Let’s take a closer look at several of the most popular methods by which this process is carried out. And let’s take a closer look at each of them.

And the very economical can make such a cutter on their own.
A scrap of a metal sheet of 2 millimeters thick is taken. Strip width. about a centimeter.
One of the edges is trimmed at a 45 degree angle.
The resulting knife sharpens well.
The opposite end is wrapped with electrical tape so that it does not put pressure on the hand.
The cutter is ready, you can start measuring the panels.

A metal tool is more convenient to use, but a hacksaw for wood is also suitable, only with small teeth for cross-cutting. over, the teeth should not be divorced so that the cutting edge is less shaggy. The advantage of this method is that with a hacksaw you can cut several panels at once (if the walls are straight and everywhere the same height), folding them in a stack.

Planks are placed face up, with a slight slope.
You should work with a hacksaw without strong pressure, so as not to break parts.
PVC is a material that is light enough to cut, so cutting problems are not expected.

Jigsaw, circular and angle grinder

They significantly speed up the process and give a fairly even cut. Practically irreplaceable for longitudinal separation. Like a hacksaw, a stack of panels can be processed. as long as its height does not exceed the length of the working surface of the tool.

There is one "but": at high revs, the panel begins to melt, which is why the edge turns out to be wavy, and unpleasantly smelling and poisonous substances are released into the air. So the work is carried out exclusively at low speeds.

In addition, efforts must be carefully measured, since all three instruments are quite heavy and, so to speak, aggressive. Excessive use of them leads to panel breakage. Given these disadvantages, many craftsmen recommend using a conventional, not electric, jigsaw for cutting. It separates the panels a little faster than a hacksaw, the cut is obtained without creases, is convenient in longitudinal cutting and is safe to use.

There is such and such a tool in any home! However, its application has its own subtleties.

An ordinary kitchen knife is most unsuitable for the pursued purpose. Even when sharpened well, it has a blade that is too wide to cut through plastic. It will turn out like Ilf and Petrov: "Saw, Shura, saw." One bar can be cut off, but if there are a lot of them, cutting your time will take more than the installation itself.
A stationery knife is more suitable: it will not cut the panel to the end, but this is not required. A groove is pressed from the front side, after which the bar breaks easily. The remaining small fringe usually does not bother anyone. this edge is still hidden under the curbs and baseboards.
The ceramic loaf knife, oddly enough, has proven itself quite well in cutting plastic panels. Due to the wavy cutting edge, it copes with PVC no worse than a hacksaw, while leaving a rather decent, not shaggy cut.

General cutting rules

When using any tool, certain requirements must be met. over, it is in your own interests if you strive to do without work injuries and unnecessary marriage.

Before cutting the panels. Brought in from the cold, they must be warmed. The main mistake of inexperienced finishers is to store the cladding on a BAL-KO and apply it as needed, immediately starting to cut. PVC becomes brittle in the cold, and the cut is fragmented. Cracking is also common almost along the entire length of the panel. So after placing the planks in the room, they are left to stand at least overnight.

You can cut (again in any way you like) only with the wrong side down. If you place the panel incorrectly, its profile will fold over and make installation difficult. The panels of some manufacturers may have more significant violations: microcracks on the front surface, which do not appear immediately.

If you are cutting a stack of panels that need to be of the same length, place them on 2 supports so that they do not sag or move. It is advisable to rest the end not cut off against something, at least against a wall. Otherwise, when the tool is applied, the elements will shift and turn out to be of different sizes.

And one more thing: when cutting, it is advisable to use protective glasses. Especially when using a power tool: the probability of a fragment flying off into the face area is quite high. And if the scratches on the hands are experienced by people indifferently, then the eye injury is much more dangerous. Naturally, it is up to the finisher to choose what to cut the plastic panels with. However, before choosing one tool over the rest, you need to know what difficulties you may face when using it. We tried to cover them in full.

How to cut tiles at home? List of proven methods
How to fix PVC panels to the ceiling? Everything is not as difficult as it seems
Decorating the bathroom with PVC panels with your own hands. Tips from personal experience
What pipes are best for plumbing in an apartment? Plastic, steel or copper?

Panel slicing rules

If the panels have just been brought from the street, especially if the temperature is low there, in this case, you cannot immediately start working. For some time they need to warm up, since cold they become even more fragile and you can easily harm the material.

Before you start cutting, you need to note where the cuts will be. A felt-tip pen is best suited for these purposes. It is clearly visible on the panel and can be easily erased later.

During work, one should not forget about safety precautions, it is better to wear gloves and glasses. The thing is that, breaking, the panels form very sharp fragments, and there is a danger of being injured by them.

And in general, this material is very fragile, so you need to work with it very carefully and carefully.

Therefore, if someone else asks himself: "What are plastic panels cut with?". then we can safely say that there are many options. And surely in the end there will be the most suitable.

The 6 Best Dog Breeds for Families with Young Children Many families decide to have a dog around the same time they have their first child. But which dog breeds are best for families.

How does it feel to be heir to the royal throne? 7 Surprising Facts Royal heirs are entitled to a range of benefits, but until recently, they were also limited by ancient traditions formed for.

How to inform your daughter or son that there will be another child in the family Are you expecting another child? Congratulations! You probably want to share this joy with family and friends, but what about older kids? When.

11 weird signs that you are good in bed Do you also want to believe that you are giving your romantic partner pleasure in bed? At least you don’t want to blush and sorry.

15 Most Beautiful Wives of Millionaires Check out the list of the world’s most successful wives. They are stunning beauties and are often successful in business.

10 Mysterious Photos That Shock Long before the advent of the Internet and the masters of Photoshop, the vast majority of photos taken were genuine. Sometimes the pictures got really wrong.

Power tool

If someone is wondering how to cut plastic wall panels, and there is an electric jigsaw among the tools, then you can throw away all doubts and apply it. After all, this is one of the power tools that is suitable for this task. But first you need to try to cut an unnecessary piece. And all in order to understand which side will be cut neatly. There is also an important detail: the file must be with a fine tooth, and the pendulum stroke is disabled. So, paying attention to all the recommendations, you can easily cut the panels. over, this method significantly saves time, because with the help of an electric jigsaw, you can cut several panels at once by simply folding them together evenly.

But often for those who are thinking about what to cut plastic PVC panels, the choice falls on a hacksaw for metal or wood, but it is important that the teeth are small. The advantage of this method is that you can cut several panels at the same time. It is necessary to cut with the right side, at a slight slope and try not to press hard on the material.

How to cut plastic panels? 4 tools to choose from to help

How to cut plastic panels has long been invented. And these methods. both folk and modern technological ones. are diverse enough for us to choose: either the method that seems more convenient, or the one for which there is a suitable tool on the shelf. Let’s take a closer look at several of the most popular methods by which this process is carried out. And let’s take a closer look at each of them.

They significantly speed up the process and give a fairly even cut. Practically irreplaceable for longitudinal separation. Like a hacksaw, a stack of panels can be processed. as long as its height does not exceed the length of the working surface of the tool.

When using any tool, certain requirements must be met. over, it is in your own interests if you strive to do without work injuries and unnecessary marriage.

Before cutting the panels brought in from the cold, they must be warmed up. The main mistake of inexperienced finishers is to store the cladding on a BAL-KO and apply it as needed, immediately starting to cut. PVC becomes brittle in the cold, and the cut is fragmented. Cracking is also common almost along the entire length of the panel. So after placing the planks in the room, they are left to stand at least overnight.

You can cut (again in any way you like) only with the wrong side down. If you place the panel incorrectly, its profile will fold over and make installation difficult. The panels of some manufacturers may have more significant violations: microcracks on the front surface, which do not appear immediately.

Power tool

The most impatient can use PVC panels for cutting with a power tool. For these purposes, any device that the master has at hand is suitable. This method allows you to quickly cut plastic, saving a lot of time. Cutting is performed using:

Cutter

This tool has proven itself well due to its low cost. Perfect for home use.

The tool has excellent performance and the cut surface looks smooth. It should also be highlighted the fact that no special physical effort is required to carry out the cutting. A huge advantage can also be called its compactness, in which it does not take up much space during its storage.

How to cut a plastic panel straight

As a rule, a quick and inexpensive repair, however high quality, is not complete without plastic panels. They have a number of advantages that make them virtually irreplaceable material in the repair. Most often used in rooms such as bathrooms, toilets and balconies.

Of the most important advantages, one can single out the fact that they are completely waterproof, do not burn well, and have a low cost. That is why they are widely used in bathrooms and toilets in order to hide plumbing fixtures. When doing repair work with your own hands, the question often arises: how and how to cut plastic panels at home. Fortunately, the installation technology of this material is quite easy, and does not require additional preliminary preparation.

The first stage is cutting. It is necessary to be extremely careful, since the final appearance of the work depends on it. Cutting is carried out strictly according to the required size, without allowing an allowance, since the material is hard.

The time spent at this stage depends on the complexity of the upcoming repair. It must be understood that a simple paneling of a flat surface will be faster than finishing a surface with various protrusions, architectural elements.

Although this material is tough, it is quite easy to handle.

Material features

PVC panels are one of the modern types of finishing materials that are made by extrusion and are used both in the bathroom and in the living room. The main raw material in the production of such products is polyvinyl chloride, which is used to fill the mold. To give the panels the desired color, a certain amount of crushed natural chalk is added to their composition.

Decorating PVC panels can be done in one of the following ways:

Staining;
Thermal printing;
Offset printing.

Thermal printing is applied to the plastic surface using a special roller heated to high temperatures, which presses the film to the surface of the product. Thanks to this technology, it is possible to quickly and clearly apply a pattern without losing the brightness of the image. The panel itself does not need additional varnish. Offset printing is used much less frequently due to its high cost.

How to cut plastic panels at home. How to cut PVC panels correctly?

To obtain a quality result when cutting, certain rules must be followed. Among them there are both general instructions and recommendations for working with a specific tool:

It is unacceptable to work with material that was brought in from the cold. it must be warmed up before opening. Chilled PVC becomes brittle, leading to edge chipping.
Wall panels should only be cut from the front side. Otherwise, the profile will collapse, and difficulties may arise during the installation process.
Using an angle grinder, jigsaw or hacksaw allows you to cut a bundle of panels at once.

In this case, they must be laid on two supports so that they do not sag, and not the cut edge must be resting against the wall. this will prevent the panels from moving during cutting.

When using a power tool, it is advisable to wear protective goggles, since the likelihood of splinters getting in the face during work is quite high.

When working with a knife, it is worth using a guide on which the tool will rest during cutting.

This, as already mentioned, can be a square or a wooden lath. The guide is applied to the cut mowing line, the panel is cut and cracked, after which the material is cut from the back.

That’s all. The main methods of cutting PVC panels have been considered and it remains only to determine the most optimal option, the choice of which depends on the personal preferences and capabilities of the master himself.

See below for a convenient way to cut PVC panels with a hacksaw:

Cutter

Experienced craftsmen, who have in their arsenal a whole set of special tools for processing plastic, are used to cut PVC panels for wall cladding with a special cutter. This useful tool makes an absolutely straight cut on plastic without the use of physical effort.

Craftsmen may well make that tool with their own hands according to the following instructions:

It is necessary to take a strip of metal sheet with a thickness of at least 2 mm. The strip must be 1 cm wide.
One edge of the metal strip is cut at a 45 degree angle.
One side of a homemade cutter is sharpened with a whetstone.
The opposite side is wrapped with electrical tape so as not to damage the hand during work.

How to cut plastic panels. three cutting methods

Thrifty homeowners know that there is no better and more practical material for bathroom and toilet wall cladding than decorative PVC panels. They perfectly replace ceramic tiles in cases where there is not enough money or time for a full repair.

This material is also loved because it can be easily assembled by hand. However, the standard panel length is 3 m, which exceeds the ceiling height in typical high-rise buildings. In this regard, inexperienced craftsmen who decided to sheathe the walls of the bathroom with their own hands, the question arises of how to cut plastic panels at home. In this article, we will talk about a special tool for sawing plastic and improvised tools that can be used for this operation.

Hacksaw

A hacksaw is a versatile tool that any craftsman has in his arsenal. It can easily cut plastic wall panels, if it is not possible to purchase a special cutter. With a hacksaw, the cutting process takes more time, but with a small amount of work, this does not significantly affect the duration of the wall cladding.

When sawing plastic with a hacksaw, the following nuances must be taken into account:

To cut PVC, use a tool with fine teeth for wood (cross-cut) or metal.
Sawing plastic does not require strong force, otherwise material may be damaged.
With a hacksaw, you can cut several panels at once, folding them in a stack.

Power tool

Sources:

http://2000sovetov.com/post-28794-chem-rezat-plastikovye-paneli-v-domashnih-usloviyah/
http://remontonly.ru/chem-rezat-paneli-pvh.html
http://remtra.ru/164-chem-rezat-plastikovye-paneli-4-instrumenta-na-vybor-v-pomosch.html
http://proteplo46.ru/dom/chem-rezat-plastikovye-paneli-v-domashnih-usloviyah.html
http://sovety-vannoy.ru/delaem-remont/steny/chem-rezat-plastikovye-paneli.html