How to cut the outer angle of the skirting board. Is it possible and how to make it yourself

How to make an angle on a ceiling plinth with a bin. step-by-step instruction

Ceiling baseboard is a decorative element that separates ceiling wallpaper or tiles from wallpaper on the wall. He completes the appearance of the room and gives the design completeness. However, in order to correctly join the two strips of the baseboard in the corner, it is necessary to correct it correctly. How exactly this is done? There are several ways to achieve the planned.

The easiest way is to fit the strips of the skirting board, cutting it with the help of. This device is a P-shaped design (something like a box without one of the walls). In the sidewalls, cuts are made in advance, which are further used as a template for cutting both skirting boards and other materials.

Cutting skirting boards at at an angle with the help of a bunny, watch in this video.

• It allows you to accurately cut the edges of the baseboard according to the finished template.
• It is easy to do it with your own hands using four planks, a square and a saw. In this case, you can cut out template grooves for every taste depending on the required type of work.
• With it, it is easy to form both the internal and external angle.

The only drawback of this method applies only to those cases when the knock is made with your own hands: it is necessary to carefully, in advance, outline lines for template slots with the help of the transporter, without deviating a degree.

Cutting the angle on the ceiling skirting boards according to the strules has its own characteristics. Perhaps you will also be interested to familiarize yourself with the article on the topic, plaster of the walls with your own hands, types of plaster.

External

For the outer corner. the baseboard is applied to the right side of the rushed (or. to the closest to itself, if the template is placed across the desktop), is aligned on the plane and wall, and then cut off or sawn off using the template.

Interior

For the internal. also, but in the reverse order: application occurs on the left or far side of the stir.

Both cut plinths are applied in place without gluing. If there are cracks. fragments are driven to each other with a knife. Small defects can later be covered with putty. It will also be useful to familiarize yourself with the article how to make a putty for walls with your own hands.

Hand Right important: even when using a template, cutting angles requires a certain skill. Therefore, for the finisher, doing this for the first time, it is recommended to first practice on the unnecessary residues of the skirting board, cutting them, and trying to join without cracks.

Features of cutting

Let us consider in more detail how to properly cut the angle on the ceiling skirting board using different materials.

Polyurethane

Polyurethane foam (in colloquial. just polyurethane) is a very good material for ceiling skirting boards. Due to good flexibility, it definitely adjacent to the base (the junction of the wall and ceiling), even if, due to building errors, the walls and ceiling are uneven. In addition, polyurethane is well washed, and therefore can serve for a long time. Low resistance to loads here is not a problem: there is almost no load on the ceiling plinth. We also have a separate article where the question of how to make a drywall ceiling and suspended ceilings made of drywall with your own hands are more details.

Cut the polyurethane skirting boat with the help of the stirred:

• Measure the wall and ceiling in the area of ​​the junction.
• Select a suitable stupor template for cutting.

Styrofoam

Foam is also often found as an element of decorative decoration of rooms. Its characteristic feature is increased fragility, so it is extremely accurate to adjust it at the place, the foam does not tolerate any deformations.

Cut it with the help of the rushed as follows:

• Plinth plates are laid in the knock.
• A cut is made. Unlike polyurethane polyurethane. soft material, and it can be cut even with a knife or better. stationery or construction cutter. It is better to use not a large, but even wooder, metal dick or ruler here. In extreme cases, you can make marks with a pencil corresponding to the slots of the stir, connect them using a ruler. and conduct a slot.

Asterisk is important: foam is a fragile material, so the cutting tool should be sharpened as best as possible.

Polystyrene

Polystyrene has the same properties as the foam. Therefore, polystyrene skirting boards are cut as well as foam. The main thing here is the most acute sharpening of the cutting edge of the tool to avoid dyeing. At the same time, there is no need to process the ends with sandpaper: their edges are usually already quite relief to ensure a good adhesion of glue.

Wood

A wooden skirting board is infrequent and is expensive, so it is necessary to approach its processing extremely responsibly. Cutting technology looks something like this:

• The cut end is fixed in the stizl.
• Cut is made. You can do this with an ordinary hacksaw on wood, but it is better to use a special saw or saw for metal to avoid too wide sawing.

Asterisk is important: when fitting, you need to be extremely careful, it is better to close the uneven cut with a decorative lining or putty for wood than to open a too large array of wood.

The skirting board made of plastic (polyvinyl chloride, PVC) is now widespread now. It is convenient because:

• Easily cut by any tool.
• Flexible, can be used even in uneven corners.
• Usually has internal cavities, which means-can be used as a cable channel for laying electrical wiring or fiber-optic lines for the Internet.

Cut a plinth from PVC as well as polyurethane. However, you need to take into account: the best tool, a hacksaw for metal with small teeth, is suitable only for thick skirting boards, in thin it can tear out pieces. Therefore, the best option for thin products is a stationery or a construction cut or a sharpened knife. To use it, you need a certain dexterity, so it is better to practice in advance on scraps or sheets of thin plastic.

Cutting with stupor: external angle

Most often, when installing ceiling skirting boards of home masters, they are interested in how to properly arrange the internal corners in the room. Cutting the outer angles is less common, but with a certain layout of the walls and it is necessary. Consider how to make an internal fillets properly using a special tool (knock).

First, you will need to purchase a knock. This tool is a tray in which the part is fixed, and its trim is made. In order to measure the length of the required product, you need to attach it to the ceiling. Further, you need to install the skirting board in the knock. Its location should correspond to the position that he will occupy on the ceiling.

Flow

Important! During cutting, it is necessary to hold a filler with his left hand. She should fit tightly against the wall of the tool. The part of the product that will be fixed to the ceiling should be on top. The other part is tightly pressed to the bottom of the working tool.

How to correctly cut the inner angle of the ceiling plinth is a difficult question, to answer the corresponding photos to answer. Experts recommend studying them, and only after that start work.

After you make sure that the product is located in the tool correctly, you can proceed to the cutting itself. The hacksaw should have a certain angle, namely: 45 degrees. During operation, it is not recommended to press hard on the cutting tool, since you can damage the surface of. Then the pruning of an adjacent filler is performed, which is made in a “mirror” way.

Cutting with stupid: inner corner

To get the right inner angle, the easiest way to use a professional tool. Of course, such a work can be done without a stop, however, but in this case you will need to make more efforts. Consider the sequence of actions for cutting the inner angle with the help of.

The first thing to do is determine the distance from the corner on the outside to the nearest wall. Further, you need to mark the baseboard, preparing it for cutting. On the outer side of the filter you need to draw a fishing line for a trimmer along the length of measurement. It is worth considering that in this case the upper part of the trash should go out a little.

After that, you can start pruning. For this, the ceiling skirting board is placed in the cutting tool and is reliably pressed against the wall. After trimming the first part, you can start processing the oncoming element.

Alternative options

We figured out the classic stupid, but how to correctly cut the angle of the ceiling plinth, if there was no specialized tool at hand? Do not despair, such a misunderstanding is easy to fix. over, some masters prefer to rely more on folk methods.

Homemade knock

The main task of the standard tool is to clearly withstand the angle of 45º or 90º. But these classic corners can be marked without resorting to the use of. In fact, for this it is enough to use a leaf into a cell from a school notebook.

With a right angle, as it were, everything is clear. And the angle of 45º is the diagonal of the square.

If you are dealing with soft material such as foam, then such a square drawn on paper is invested in any correct angle. Next, you have to put a filler in this corner and cut it off with a knife at the right angle.

Everything is a little more complicated if you are dealing with a wooden or PVC play. Here, before cutting the baseboard at the corners, you will have to build a knock with your own hands.

To do this, you need to knock down two wooden or any other strips at right angles, mark and cut into them the guide holes. After which you can invest in such an impromptu hook of the fillets and, as sculptors say, cut off the excess.

Simple and affordable

Now we will talk about the simplest, accessible and at the same time universal way.

There is an instruction for which you can quickly, and most importantly, precisely mark not only traditional corners, but also any other non.standard angles.

Important: In this method, the main problem is the exact cut. After all, most often you will have to hold and cut the bar by weight. In this case, you can’t do without a good skill of working with a hacksaw.

• First you need to cut a filler so that the lower edge clearly enters the inner angle, in standard rooms it is 90º. After that, it is placed in its future place and with a pencil, a fishing line is held for a trimmer on the ceiling along the upper edge, as in the photo;
• After the first fishing line for a trimmer is ready, we do the same procedure with an adjacent surface. By the way, so as not to wash the fishing line for a trimmer from a pencil, you can draw with a knife or any sharp object;

Important: this method is good because with it you can both cut the ceiling plinth in the inner corner and work with the outer corners. over, as you see, it does not matter here at all whether it is a straight angle or not.

Important little things

Often, novice masters have a serious joining of corners with a serious problem. Having bought a knock on the market, since the price is affordable, people boldly cut the bar, often not given the possible curvature of the walls. And such a curvature has at least half of the corners in our homes, as a result, gaps are obtained.

Of course, the easiest way out will be covered with special putty using a soft rubber spatula. There are enough such putty for any material, color and even tone in the modern market.

But experienced masters prefer to leave a small tolerance when marking, about 1. 3 mm. If the angle is clearly combined, then this admission is compensated at the next corner. And if there is a gap, the edge of the baseboard can be trimmed with a knife.

The next stumbling block is the problem of how to cut wallpaper for a ceiling baseboard. Everything ingenious is simple, here you will need to buy a roll of construction tape and stick it to the lower slice of the baseboard before work. The wallpaper is measured with a small drop of 10. 15 mm, and after the end of the work they are cut with a sharp knife, pressing with a spatula, and removed with adhesive tape.

Tip: take the construction tape. On smooth filtles, a transparent stationery adhesive tape will stick tightly and you, to put it mildly, “get tired” then tear it off.

Using a spatula when trimming wallpaper.

Cutting floor plinth using

For the proper pruning of the baseboard, a special device was invented, which was called the knock. It is a small bar with a pinch aispela and with gaps located at different angles. for a cutting tool.

With the help of the stir, you can get neat and even sections. The skirting board is fixed inside the product, then the angle desired in a particular case and the direction of the cut is selected.

On a note! If it is necessary to form a beautiful angle with the help of a binker, then one piece of plinth is cut at one angle, and the second in a mirror display.

While working with the stupid, it is important to ensure that the edges of the baseboard protrude beyond the edges of the selected slot over a short distance. If the trim tool has a large width than the skirting board itself, then it is recommended to secure the product inside theur. Otherwise, the baseboard can move inside, the cut angle will constantly change, which is why it (cut) will turn out to be incorrect and wrong.

Execution of sections for joining skirting boards using

Important! During the saw, the pressure on the baseboard should be moderate. Otherwise it may break.

Using a ruler and a pencil in the absence

If there is no bid at hand, but I don’t want to do stencils, then you can try to apply the necessary marking to the skirting board with a pencil. In the case of the formation of the inner angle, the width of the product is measured, then the resulting value is put off on the end part of the skirting board, and from its angle to this marked point a fishing line for a trimmer with a pencil is carried out, according to which the cut will be made. The second skirting board, which will, together with the first, form an angle, is simply cut through the first attached to it.

Important! If the installation of skirting boards is performed in a room with complex geometry, then all angles will have to be thoroughly measured to prevent a mistake.

Floor skirting board in non.standard angles

Useful tips

Experienced masters recommend starting the installation of a skirting board from the inner angle. At the junction of the two walls, which form the inner angle, the cut on skirting boards will be 45 degrees (in the room with the correct and accurate geometry). It is recommended to cut the cutting with the help of a cherumn. the only way can you achieve a perfectly even cut.

Cutting floor and ceiling skirting boards using

Advice! If necessary, you can slightly adjust the plinth to each other with a grinder or rashpil, slightly “removing” their edges.

In general, in any case, the cut edges of the plastic skirting boards should be sanded. it will be possible to get rid of sharp edges, and it will be easier to work. And cutting skirting boards with cable channels is carried out only after disassembling the product-a decorative bar designed to conceal the wires and location of the skirting board separately.

It is recommended to cut the segments on the required length and arrange the corners before installing the baseboard so as not to be distracted by this procedure during the assembly of the skirting board. Do not neglect the use of additional elements. plugs, corners and other skirting products. With their help, it will be possible to give the finished work a complete and harmonious view.

Advice! If the angles where the skirting board is laid and joins, then even decorative plugs and other elements can be trimmed if necessary.

With this device, cutting skirting boards at any angle is very simple

Principle and rules for working with device

For many owners of the apartment or house on their own, it is the news that there are special devices for cutting the corners of the baguette. Therefore, they are poorly oriented in how to use a stupid for skirting boards.

The very principle of using the device is extremely simple. The baguette is taken and attached in stupla opposite the slot in 45 O in the same position as it will be glued to the wall. At the same time, he should play 1-2 cm beyond the boundaries of the zone, in which the angle will be carried out, which will allow you to get even, without chips, end. The processed part is fixed with clamps, and if they are absent, pressed to the base of the device device. There is a small trick: it is more convenient to cut if the saw is from the side of the working hand (the grooves in the tool allow you to do this).

Knowledge of the principle of work does not guarantee the exact and beautiful compound of the baguette in the corners. It is also necessary to know the basic rules, how to cut a ceiling plinth on a stuplet.

• The cutting tool must correspond to the material of the filter. Foam is best cut with a knife with a replaceable blade. Plastic. with a knife, a hacksaw for metal or corner grinding with a cutting circle having diamond spraying. Wooden filler. wood with a small tooth.
• Bagets with a relief or ornament must be combined by the drawing.
• In order to prevent errors in determining the direction of the cut, you need to outline the fishing line for the trimmer in advance, which will go for the saw. There is no particular accuracy here: the main thing is to correctly indicate the selected direction.
• You need to start a cut after checking the quality of fixation of the skirting board in the tool: is it installed correctly; how reliably fixed.

Which one to choose in the store

When choosing a device, you need to focus on its functionality (at what angle and what planes to cut the workpiece) and the volume of work performed. Simple, P-shaped tools are bought if you have to install a floor or ceiling skirting board on their own, rotary are intended for masters. If you need complex, in 2 planes of cut, then the non-professional will have to buy a turning point.

When buying, you should pay attention to the following characteristics:

• the material from which the device is manufactured;
• the width of the base;
• wall thickness;
• the presence of a cutting tool in a set;
• the number of slots (the more there are, the better);
• the presence of clamps (latches);
• how free the progress of the saw.

You can buy a simple device without a hacksaw for 87-820. The cost of a swivel was starting from 1300 to say how much an electric tool costs, even approximately, difficult. The screening of is huge. You can buy a end saw and for 6 thousand And for 25 thousand.

“Fit 41255”. The model is made of durable plastic. There are slots at angles at 22.5, 45, 90 and 135 O for vertical cut and 45 O for inclined sawing. The price of the tool starts from 335

“Stanley1-20-112”. Material. solid shockproof plastic. Saws can be done at an angle of 22.5, 45 and 90 O vertically and 45 O horizontally. Allows you to make very accurate cuts. The cost starts from 770

“Zubyr15375-75”. Made of impact-resistant technical thermoplastic resin (ABS-plastic), which allows you to maintain the size of the slot for a long time. You can buy for 220-340.

FIT PRO 41321. Professional turning. The bed can be steel, aluminum or plastic. The saw is delivered in the kit. Costs from 3500 to 6700

They have another advantage: if you cut off too long stripes, the baseboard in the corners must be cut at 90, so “not to get” will be more difficult.

You have already learned about how to correctly cut the ceiling skirting boards in the right corners, but non.standard situations also happen. They are found if there was a redevelopment in the apartment, but you did not take into account the molding.

So how to correctly cut a ceiling plinth in indirect angles? There are several recommendations.

Stupid

Dumb name is a slope of more than 90 about. Often it occurs on the protruding parts. Do not even try to find such a slope on Stusl, because in factory models it is not done. A professional saw for corner cuts is suitable, but few people have it at home.

Since make the outer angle of the ceiling plinth even? If the polystyrene molding, just heat it with a hairdryer.

From the temperature it softens and you can give it the necessary shape.

Do not try to cut the corners of the ceiling plinth correctly, it is very difficult to catch the desired slope.

Sharp corners are fitted similarly. Before gluing the ceiling skirting boat from foam. warm the corner and form the desired slope.

Rounded

But how to make a “round” angle on the ceiling plinth correctly? It is harder here, because the foam cannot be warmed up to such plasticity. The only option is to crush it into small parts and glue the ceiling plinth in the corners like that.

Here it is worth considering that at the back of the molding there are often stiffener ribs that do not allow him to go around circles in the necessary form. Therefore, even in small areas, it is better to cut them several times by the longitudinal line.

If the rounding is small, you can cut into such parts.

But in this case, so that the joints are more or less even, cut the corners.

With plastic molding is still easier. It is enough to do the slots on the back edge in this way and bend.

A similar technology works with wooden molding. It must be cut into several cones and collect roundness.

Before starting work

The choice of the correct width of the baguette is the key to a beautiful interior. An important role in the sawing process is also played by the method by which you do this. We want to give you a couple of recommendations that will help to achieve their plan.

So, how to choose the width of the material and how to cut the ceiling baseboard in the corners:

• The prepared surface of the walls is not a standard of evenness, use planks of smaller width, as they are more flexible and will be able to close the maximum number of defects. Accordingly, the opposite, the more perfect the surface, the larger the width of the molding can be, however, keep in mind. mount a narrow baguette in rooms with low ceilings so as not to reduce them visually;
• Always apply the left side of the corner to the stitches while dripping on the left, the right. on the right. In addition, it should be the side of the tool closer to you, distant. for floor moldings. Please do not confuse.

How to cut the corners on the ceiling of the baseboard under 45 degrees

Below we will deal with the set task, where you will find out. how to cut the corners of the ceiling plinth correctly and with the greatest quality.

External

There is one nuance of this process that you should never forget about. We always look at the ceiling below, therefore, when the bar is placed in the knock (to the wall closer to you), it must be turned upside down.

The upper part of the molding will then have below, and the lower, respectively, at the top. Thus, there will be no gaps between the planes of the angle when they connect.

In the photo. a knock, a carpenter tool in which the corners of the ceiling plinth is cut

• Take measuring tools, for example, roulette, and pencil. Start marking from the inner angle, so you will not miss the external. It may happen that there is not enough baguette length and you have to do many joints;
• Apply molding to the ceiling surface and mark the dimensions;
• Prepare a knock and a hacksaw for metal. Press the baguette to the instrument near your side;
• Keep a tick with your hand and select the position of the hacksaw in which the corresponding angle of connection will be set. These can be standard parameters. 45, 90, or 135º, or arbitrary, for which it is necessary to push the knock into the chosen degree;
• Cut the workpiece with a hacksaw;
• Install the opposite bar to the near wall of the tool and fix it with your hand;
• Put the chosen degree on stuplet and cut the workpiece with a hacksaw for metal;
• Coasten the resulting plinth planks.

Tip: if the walls are interconnected at a right angle, only in this case you will help you in the work of the knock, otherwise you will have to fit your own hands.

Interior

There is a professional knock, which has a rotary platform and can be extended to obtain arbitrary angles, as well as for home use, where special opportunities are limited. Usually in the repair it is enough to use the second option.

How to cut a ceiling plinth in the corners without gaps

So, the basic principle. ceiling strips are cut off at the closest wall of the tool, we hope you have not forgotten.

• Measure the required baguette length, applying it to the ceiling surface;
• Put the barbood bar in the knock, while its position should fully correspond to the location of the baguette on the ceiling;
• Press the bar to the near wall of the tool;
• Select the corresponding degree of the cut, most often it is 45. Make sure that the knife handle is as close as possible to the hand holding the bar to make the cut as accurately as possible;
• Cut the workpiece, but do not apply unnecessary efforts to a hacksaw;
• Prepare and cut off the opposite baguette bar, not forgetting that it should be pressed against the near wall;
• Select the corresponding angle of the cut for it, leaving a minimum distance between the knife handle and the hand holding molding;
• Cut the edge of the bar.

Proper pruning of ceiling skirting boards in the corners improves the appearance of the room

It remains to check the correctness of the docking of the segments, and if everything corresponds to expectations, install them in place.

Tip: Start cutting from the front of the molding, then you can orient it on the spot as accurately as possible. The corners of the wooden baguette after cutting, treat and adjust the file.

How to cut the corners of ceiling skirting boards with a hacksaw and

How to make the corners of the ceiling baguette without rushed

For the first time deciding to make a frame on the ceiling, the beginner does not see any problem in this, but in vain. We advise you to immediately take into account the cost of a certain amount of material, which will just have to be thrown away.

Alas, at what angle to cut the ceiling baseboard depends only on the connection of the walls with each other. Not everyone corresponds to direct, for which it is enough to simply cut off the bar under 45 °. Often there are parameters corresponding to 85 or 95 degrees, but this is already a problem for beginner finishes.

If it seemed to you that work to create a beautiful interior using a ceiling baguette is quite complicated, this is only at first glance. Do everything according to our instructions and you will quickly understand the essence of the process. The main thing is to comply with accuracy and correctly calculate the amount of material for work.

Several recommendations

Any work has nuances, but they cannot be perceived with trifles. In order for pruning to go carefully and without problems, you need to pay attention to several points.

• Correct measurements. the most important thing in any work. To mark the blanks for the inner angle, the measurement begins precisely from it.
• Before cutting off both planks for the outer corner, they do not forget that for it they will “peek” for a length equal to the width of the products.
• Fixation of ceiling baguettes begin only after several checks carried out. When the edges of the skirting boards are perfect, then you can start gluing them (with self.tapping fastening).
• To correct the connected blanks, you can use files or files. For polystyrene and both types of polystyrene foam, it is necessary to take thin, sharply bidders.

Since any debut rarely passes without errors, it is recommended to start with training on scraps. Therefore, when buying it is better to add 10-15% to the length of products. So it can be guaranteed that the material is enough not only for preparation, but also for the entire room, even if the flaws still appear in the process of work.

What to do if the gaps remain?

If defects are found after completion of work, then few people will like the prospect of remaking it. In this case, it is easier to disguise them with one of the compositions. The best option for such processing will be the final acrylic putty. It has white and very plastic. The material is taken with fingers, then it is pressed into the remaining gap, carefully distributing it in the hole, yielding. The remaining composition is removed with a damp cloth. As a rule, there are no traces of imperfections at the joints.

How to cut a ceiling plinth? You need to stock up on the necessary tools and patience, since rush always provokes mistakes. The main thing in this case is the choice of the optimal way. But attentiveness and accuracy are no less important: skirting boards are made of not too strong material (exception. wooden baguettes). They are fragile, so excessive efforts when working with such products are contraindicated.

The author of the following video, which the audience considers the simplest and understandable: about how to cut a ceiling plinth will tell about how to cut a ceiling skirting