How to get a fishing line for a trimmer to a motorcycle. Cords of cord

trimmer for grass gasoline stihl how to refuel a fishing line for a trimmer. We change the fishing line for a trimmer in a trimmer (lawn mower)

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

How to replace a fishing line for a trimmer on a trimmer how to wind a fishing line for a trimmer for a trimmer for grass

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Coil with one working osik

The easiest option and a simple sequence of actions:

The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the fixing technological hole located inside the spool.
The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobbin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Read how to clean the air filter on the echo trimmer

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

Exclude spontaneous start,
Delete the battery (if used),
Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Read how to put a fishing line for a trimmer on a trimmer for grass correctly

How to choose a fishing line for a trimmer. length, diameter, restrictions

For any electric or gasoline trimmer for grass, you can use fishing lines of different manufacturers. However, the best option is the consumable of the same brand as the tool. It is believed that in this case it will benefit the durability of work and even reduce the consumption.

ВАЖНО ЗАПОМНИТЬ! Нельзя использовать для триммера для травы рыболовную леску для триммера или металлические тросики. Такая замена не эффективна и опасна. Трос может травмировать не только самого косильщика, но и окружающих.

As for the length, it is worth counting on the estimated frequency of using a trimmer for grass. The more often, the more it is worth stocking up. Information about the possible diameter of the fishing line is found on the body of the coil for a trimmer for grass. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose a suitable option, taking into account the features of the processed territory. The larger the diameter, the easier it is to mow hard grass.

How to remove a coil from a trimmer for grass and extract a fishing line for a trimmer

Initially, before filling the fishing line for the trimmer to the coil of the trimmer for the grass, it is necessary to extract it from there. Coil or tip is a device that is located inside the braid, bobbin or drum. The heads are of different types (depending on the manufacturers), however, the principle of replacing the fishing line on the coil has the same. First of all, we will figure out how to remove the head from the tool, as well as how to get a drum with a fishing line from it.

It is interesting!The replacement of equipment can be done directly on the tool, but if you do it for the first time, it is still recommended to remove the head, and study the detailed process of winding. After the technology is mastered, you can perform work on replacement on a trimmer of a motorcycle or a gas station. Instructions on how to promote a hand head on a trimmer, has the following look:

Turn the instrument with the head to the top, and if necessary, cleanse it from pollution. Take two fingers of one hand by the cover of the cover (on the mowing head), which are located symmetrically to each other. After a light pressed inward, dismantle the protective cover from the drum

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how replacement is performed. When dismantling, consider the following nuances:

It is recommended to remove the head periodically to prevent the corrosion of the threaded connection. If you never unscrew the screw, then if necessary to do it will be difficult and even sometimes impossible
If the screw has a tetrahedral boring of the head, then for twisting you should select a screwdriver or bit of a suitable size to eliminate the licking of the faces on the head
When assembling the installation, a threaded seat should be treated with lubricants, for example, solidol or machine oil
If the edges on the screw are licked, then for its unscruptions you can use special clamping forceps
There are drums that do not require preliminary disassembly. To dismantle them, you should take up it, and rotate in the opposite direction of the direction of the clockwise

Knowing how to disassemble the drum, you should continue to clarify the process of replacing a trimmer fishing line for grass. Below the video shows a detailed process how to open a trimmer coil for grass and disassemble it.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the fixing technological hole located inside the spool.
The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobbin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

Instructions

In order to change the fishing line for the trimmer, it is necessary to extract the old one (if it was).

The coil is part of the design of the trimmer for the grass, which is located inside the head of the motorcosa, drum or bobbin. Depending on the manufacturers of the head can be different. But this article discusses only Patriot, although their mechanism is used by many other companies.

Now you need to understand how to properly remove the head from a trimmer for grass and how to get a drum out of it.

Instructions on how to promote a hand head on a trimmer is described below.

First of all, you need to clean the head of dirt and adhering grass if it is contaminated. To do this, you need to raise a motorcycle head up and, holding the casing, remove a special protective cover dressed on the drum.
The next step needs to remove the reel from the drum. The coil is easily removed even with one hand, because it is not fixed inside the drum.
The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with a coil, while twist the screw counterclockwise.
Now you can pull the coil out. As mentioned above, it is not fixed in anything except a hook with a metal shaft, so it does not need to be torn off with force. Neatly, in a circular movement you should pull the coil from the drum.
Now it remains to extract an old fishing line for a trimmer and follow the following instructions.

fishing, line, trimmer, motorcycle, cord

Installation of the coil and drum in its former place is performed according to the opposite algorithm.

Before the process of refueling the fishing line, it is worth making sure that the thread suitable for a trimmer was bought. In the case when the thread is not suitable, the fuel or energy consumption increases, as well as the load on the motor motor.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m fishing line. A specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the coil itself. If it is not possible to accurately determine the length, it can be done as follows: insert and wind the thread to such a state that the coil is completely charged (the level of the fishing line will be compared with protrusions in the sides of the coil). It is necessary to ensure that the fishing line for the trimmer sits in the coil exactly.

Do not forget that the thick thread will be shorter than thin.

The instructions for refueling the fishing line in the coil is described below.

The prepared thread must be taken and turned in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m.
Now you need to take the ends in different hands. The one that is smaller must be pulled to more, so that it becomes 2 times shorter. When bending, the indentation should be maintained at 0.15m.
Find the slot inside the coil partition. Carefully prick the loop that turned out earlier in this slot.
To continue work, it is necessary to determine the direction of winding the thread in the coil. To do this, just examine the coil. there should be an arrow on it.
If the gunner could not be found, it is quite possible that there is a written designation. An example is given in the photo below. It is necessary to inspect the head of the coil. It has a direction indicator. However, this is the direction of the coil movement. To get the direction of winding, you need to wind in the opposite direction.
Now you need to season the reel with a fishing line. It is worth noting that there are special guide grooves inside the coil. When wrapping a thread, you need to follow these grooves, otherwise you can damage a trimmer for grass. At this stage, you need to charge the coil very carefully.
When the user winds up almost the entire thread, you should take the short end (do not forget about the protrusion of 0.15m) and stretch it into the hole located in the coil wall. Now you need to repeat this action similarly with another end (on the other hand).
Put the coil itself in the coil head, before that, extinguishing a fishing line for a trimmer through the holes inside the drum.
Now is the time to return the drum to your place. After that, you need to take with both hands by the ends of the fishing line and pull them to the sides. Then you need to put the lid in place (here you can safely make efforts until a characteristic click is heard).
Remained to perform “cosmetic work”. You need to see if the thread has come out too long. You can start a trimmer for the grass and check in practice whether everything is comfortable. If the thread came out a little long, you can cut it with scissors.

Frequent errors

Although the winding of the fishing line is a very simple task, many newcomers can wrap a fishing line for a trimmer incorrectly. The most common errors are presented below.

Many people when measuring the thread think that 4 m is a lot. Because of this, people often measure less, and they, accordingly, do not have enough fishing line. Do not be afraid to measure a lot, because you can always cut off the excess.
In a hurry, some people do not observe the gas stations inside the coil and wind up the thread like it. This leads to the “departure” of the fishing line from the coil and can even cripple.
For winding, it is worth using only the corresponding fishing line for the trimmer. This error is most common. You need to monitor not only the thickness and volume of the fishing line, but also your type. You should not use the first fishing line for a trimmer for wrapping, which will not match the goals. For example, you do not need to use a thread on the young grass, if it is necessary to mow dry.
Do not turn on the device until complete winding and collection. Although this is obvious, some people do this in order to check if everything is done correctly.
In no case should you confuse the refueling direction, as it will overload the engine, and it will soon get out of the working condition.

Beginners are quite characteristic of mistakes, so it is necessary to observe the advice given in this article.

Features of the use of trimmers

A trimmer for grass, mowing grass with a fishing line, can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flower beds, a row in a garden plot.

Such a convenient, and most importantly, effective device, like a trimmer for grass, exists in several variations:

As the names understands, the types of trimmer for grass are noticeably different from one another. But regardless of the type of this tool, its cutting element can be a fishing line for a trimmer. Of course, a trimmer tilted for the grass for a trimmer is not infinite. And sooner or later it will need to be replaced by a new.

Fishing consumption directly depends on the frequency of using the device and the scale of the work performed. The more herbs are brazen and the more often it is trimmed with a trimmer for grass, the more actively a fishing line for a trimmer is consumed in it. And, accordingly, the faster it will end. In this regard, the question arises: how to refuel a fishing line for a trimmer to a trimmer coil for grass?

Not everyone knows the answer to this question. But the winding of the fishing line on the coil plays an important role in the work of a trimmer for the grass. To make the device normally, it is very important to correctly wind a new fishing line for a trimmer to the reel. About how to change a fishing line for a trimmer on a trimmer, and will be discussed in this article.

Which line for a trimmer to choose

Before you stock up on this material for refueling in a trimmer for grass, you need to decide on the choice. After all, the usual so.called round fishing line for a trimmer is far from the only existing look. How to choose the most suitable? First you need to determine the working conditions.

Alpha String Test: What Happens if you Use METAL WIRE on Weed Eater ?

Type choice. a line for a trimmer with a round section is the most common. It will suit any reels with the rarest exceptions. This type of consumable is suitable in order to mow fresh, juicy grass. But with the mowing of the so.called dryness, this kind may not cope anymore. It is pointless to mention attempts to mow shrubs and mention.

In addition to the usual type, there are others with sharp faces. Usually they are made by a “star” or “square”. The presence of sharp faces is the main feature and key difference between these threads.

It is thanks to this feature, the threads of such species are able to mow dry weeds. But the spicy threads are not devoid of disadvantages, the main of which can be called rapid wear and strength, markedly inferior to the round type.

In addition to the already mentioned types of forests, there are still interesting and often encountered varieties. Especially among them can be noted fishing lines, inside which a metal wire is stretched. Threads of this type are often used in tools working on gasoline and having an engine more powerful than one and a half horsepower.

Threads with a metal core come both with a round section and with sharp faces. Regardless of the type of cross section, such threads are the best suited to overcome hard.to.stop plants. Threads related to this type easily mow not only dry grass, but even small shrubs.

The threads with wire inside are favorably different from other types of consumables for their incredible wear resistance. But unfortunately, this feature has a more than noticeable effect on the price of this type. The cost of threads with a core significantly exceeds the cost of threads of other types.

Choice in thickness

In addition, special attention should be paid to the thickness of the consumption material. For mowing young grass, a thread is suitable with a diameter of one and a half millimeters. The larger the diameter of the thread, the more dry and rude weeds it can overpower.

When choosing a fishing line in thickness, there is one “but”. It is important not only to evaluate the capabilities of the material, but also to take into account the features of the trimmer for the grass. You must definitely look into the user’s management, which is attached to the tool, and find information about the requirements for the cutting element.

The use of inappropriate thread can lead to the failure of the tool. The use of too thick thread will entail the overload of the device engine. And the use of too thin thread will significantly increase the wear of the torque.

That is why it is necessary to approach the choice of consumables no less responsibly than to refuel in a trimmer for grass. When a suitable fishing line for a trimmer is found and purchased, you can begin to consider the ways to wind it on the coil.

Choose a fishing line for a trimmer

The fishing line for the trimmer should be strong, stiff and flexible. in the trimmer it serves as a working tool for cutting grass. Flacks of different thicknesses are made. from 1.2 mm to 4.0 mm. Most models are designed for the maximum thickness of the thread of 3 mm. What is the diameter of the fishing line for the grass for grass in one case or another depends on a number of factors.

Depending on the hardness of mowing vegetation:

It is important to consider that too thin thread accelerates the wear of the motor, too rough. will accelerate its overheating and premature failure.

The structure of the cord of the fishing line matters:

round. universal, most durable, for rough grass;
curly. for soft plants;
Twisted with notch. for thin long stems.

Important! Choose a fishing line for a trimmer of the type and parameters that the manufacturer Motokos recommends. Such material will work for a long time and efficiently with optimal loads on the product of the product.

How to change a fishing line for a trimmer on a trimmer

The fishing line for a trimmer is wound on a coil (bobbin), which is located in the body of the head of the trimmer for the grass. First, unscrew the head from the bar with the motorcycle cord and open it the top cover, pressing on the side latches. In some models, the case simply spins.

We take out the coil, clean it from dirt, the remains of the old fishing line. Coils are one- and two-section.

Fishing line winding on a single.section coil

We take 2 m of fishing line, we spread it up to half through a special hole inside the coil. The ends of the fishing line of the same length stick out from both sides. We wrap them with both along the groove of the coil in the direction indicated by the arrow on the case (back to the rotation of the coil on the shaft of a trimmer for grass). We do not wound the fishing line for the trimmer to the end-pieces of 10-15 cm, which will be workers, fix in grooves on board the coil. Fixation is needed so that the fishing line for the trimmer is not unwound when installing it in the head of a trimmer for grass.

We insert the coil into the body of the head, while at the same time we spread the free ends of the fishing line into the holes of the body, set. We collect the head, put it on a trimmer for the grass. Everything, the change of fishing line in the trimmer was carried out.

How to wind a fishing line for a trimmer for a trimmer for grass with a two.section coil

If there are two sections in the coil, put the fishing line for the trimmer in half and insert the fold place into a special groove in the side between the sections. We begin to wind the ends each in its own groove. then everything, as in the case of a single.section coil.

How much fishing line is wrapped on a trimmer for grass? You can wind 2-4 m, depending on the product model. In each case, it is impossible to wind too tight, the thread should have a free move for stretching during operation.

Fishing lines winding algorithm

The procedure for winding the fishing line depends on the type of coil. with one or two antennae, as well as with automatic charging the cord.

On a reel coil

Winding a fishing line for a trimmer to a coil with one osik is very easy. In such structures, depending on the brand of a trimmer for grass, from two to five meters of the cord is placed. The edge of the fishing line in the spool must be tucked into a special hole or groove, after which the string is wound in the direction opposite to the rotation of the coil during operation.

Advice! To understand which way to wrap the thread, you should look at the corps of the spool. usually marks are made on it indicating the direction of movement of the coil during operation.

After the fishing line for the trimmer is windpowed, you need to leave a small piece (15-30 cm), walk into the output of the spool and collect the head again.

To a coil with two antennae

In the rogues of this type, you need to inspect the inside of the coil and determine the number of grooves for winding the cord provided for in it.

Important! If there is only one gutter in the coil, then both antennae must be wrapped in a common groove, if two, then on separate paths.

For winding, you need to take a piece of fishing line with a length of two to three meters. For a spool with one groove, tie a fishing line for a trimmer into a through hole, combine a mustache, leve and wind it up in the direction in the direction of its rotation during operation. If fixing grooves are provided, they need to go through the ends of the cord, then stretch them into the output, and then close the coil and put them in the same place.

For a two.lep mewood, the difference is that the section of the string should be folded in half. Next, it is necessary to charge the middle of the bend into the groove between the grooves, and then wrap each of the pieces of fishing line on its path, fix the antennae and assemble the coil as well as the spool with one track.

On a trimmer head with automatic dressing

For heads with automatic refueling, it is enough to just start and squeeze the edges of the fishing line, and the tool will perform further winding on its own when turning on. It is impossible to make a mistake here, because the coil itself recognizes how the antennae should be located.

On a note! The advantages of trimmers with such a head include the convenience of laying the cord, and the disadvantages. high cost and complex repair.

Fishing line for a trimmer. varieties and the ability to replace other material

A cord for a trimmer for grass can be of different diameters (from 1.2 to 4 mm), and it must be chosen depending on which vegetation is required to mow. the thicker the fishing line is for a trimmer, the more rough grass it will cope. Experienced users recommend putting a fishing line for a trimmer 2 mm thick, which is a universal.

The shape of the fishing line can be round (for juicy grass) or with sharp faces in the form of a square or asterisk (for beveling dry grass). The second type is less durable and wear out faster compared to the round cord.

One of the popular issues regarding the work of trimmers is whether it is possible to replace a special cord for mowers with other materials, for example, metal or steel cables and strings, wire, etc.D. You need to know that the installation of such items is not recommended, because along with them the trimmer for grass turns into dangerous equipment. During the mowing, pieces of wire or metal will constantly break off and fly off in different directions, risking to injure the employee. And if you accidentally touch their limbs during work, a serious wound is provided.

Owners of trimmers interested in whether it is possible to use a fishing fishing line for a trimmer, we answer. this is allowed, but it will be much faster to tear and wear out, which means it is a frequent replacement.

Advice! The fishing fishing line for a trimmer is good for cleaning herbs near a fence or metal mesh-instead of spending an expensive trimmer cord, you can charge a large caliber tackle (2-3 mm), which is much cheaper.

How to choose a suitable fishing line for a trimmer?

For trimmers working both from electricity and gasoline, nylon fishing lines are suitable. This consumable can be used for both a hand tool and for a lawn mower on wheels. It is important to choose the right fishing line for a trimmer, as this directly affects the result of the work and the service life of the unit. Of course, in the proposed assortment of forests it is very easy to get confused, especially beginners. However, there are many tips from specialists and those who have already tried various options.

For an electric trimmer for grass with a capacity of less than 500 W, a thin fishing line for a trimmer with a diameter of 1 to 1.6 mm is suitable. She will perfectly cut the lawns with low grass. If the tool power is in the range from 0.5 to 1 kW, then it is better to give preference to a fishing line whose diameter will be 2 mm or slightly larger.

This will be enough to mow thin grass or grown weeds, but not too thick.

For gasoline trimmers, as well as motorcycle, you can not take a fishing line for a trimmer less than 3 mm. Such a thickness will easily cope with any weeds, dry stems, thick grass. A diameter of more than 4 mm is suitable exclusively for gas troops with high power. It turns out that a thick fishing line for a trimmer is necessary for powerful equipment. It is not recommended to use it for low.power trimmers, otherwise it will work poorly, constantly wound on the coil and create an additional load on the engine.

As a rule, in standard packaging is up to 15 meters of fishing line. However, to replace the string on the coil, about 7 meters long enough. It also happens that a fishing line for a trimmer is produced by bays of 250-500 meters. Be sure when choosing a string, you need to clarify the date when it was made. Too old nylon can be superior and become too brittle. If this happened, then you can soak the fishing line for a trimmer for a couple of hours in water, but it will not be completely the same.

When choosing an important parameter, the section of the string, which is of several types.

Round section is universal. It is used for mowing grass of medium thickness and density. When working can be unnecessarily noise, but it is not used too quickly.

Square or polygonal section is more effective compared to round. Thanks to the sharp corners, the stalks of plants are cut off at a higher speed and better.

Ribbed, twisted and star.shaped section is the most effective. Such a fishing line manages to mow the grass very quickly. And its main disadvantage is to quickly wear.

The fishing line for a trimmer for a trimmer for grass is made of nylon, which is durable, light, low price and wear resistance. To make the cost of the material even cheaper, polyethylene is added to it, but then the fishing line for the trimmer overheats faster. In thick strings there is a rod made of graphite or steel. Sometimes they are reinforced, which increases the strength and service life.

It is worth noting that the for two.component strings are higher than for standard nylon.

The device is in a mower

In the trimmer, the element on which the string is pulled is very simple. It is called the “coil”. Usually it consists of the upper and lower part (grooves), between which a partition with a deepening passes. It is on these grooves that you need to wind a fishing line for a trimmer. However, before it is extended through the recess.

Before pulling out the coil, you should twist a special button located directly on the housing of the lawn mower. Before changing the fishing line for the trimmer, it is necessary to remove the coil from the mowing.

It is easy to do this, but there are features depending on the configuration of the trimmer for the grass and the coil itself.

In small electronic braids, the motor and coil are in the lower part, and buttons are located on the sides of the bobbin. If you press them, then get the upper groove of the coil and part where you need to wind the fishing line for the trimmer.

In lawn mowers with a curved bar, which are not provided for a knife, the coils have special two.horned nuts. In such tools, you need to hold the bobbin so that it does not move, and at the same time turn the nut out of clockwise. It is she who holds the whole bobin, which after that is easy to remove.

EASIEST WAY TO STRING YOUR WEED EATER

Direct rods on which you can install a knife have a hole right under the bobin. To remove the coil, a screwdriver is located in this hole, the bobin is fixed. After that, you need to turn the coil on the movement of the clockwise and remove from the unit.

Sometimes clamps on the coil in the form of latches may occur. They must be pressed to disconnect parts of the coil. The option is also possible when the top and bottom of the bobbin are connected by thread. In this case, it is enough to take your hands on the top and bottom, and then twist in different directions until they develop.

Tips for choosing fishing line for a trimmer for grass

Coil. the main component of motorcycles. For a bevel of grass, it is equipped with a special fishing line. This very fishing line for a trimmer can serve you for a very long time, if you do not regret it (fishing line for a trimmer for a trimmer for grass. what you should not save on). Currently, you can find different cutting threads that differ in their cross.section, composition and thickness. Often a fishing line for a trimmer is sold in small or large skeins in specialized stores. If you want your mower to serve you for a long time, approach the choice of fishing line with full responsibility (because due to the wrong choice you can even break your device).

Never choose a thread for “save”. Having bought the cheapest and, obviously, the most low.quality fishing line for a trimmer, you can lose much more. As a rule, the best parameters are indicated on cheap (“Chinese”) fishing lines, but in fact they are completely different. The consequences of buying the cheapest threads can be both a breakdown of the thread and the fact that the lawn mower will fail. If the coil quickly fails, you will have to replace it again, which means you spend even more money.
Buy fishing lines only in specialized stores or from sellers, in which you are 100%sure so as not to be deceived.
Always check the authenticity of your fishing line. It’s no secret that the goods can fake, and the coils are no exception. If you decide to buy a high.quality brand thread that will last you for a long time, look for special holographic signs or codes on its package. With their help, you can easily check the authenticity of the fishing line.
In addition to the advice above, if you choose a high.quality brand for long work, choose a fishing line for a trimmer from German or Japanese manufacturers.
If your lawn mower or trimmer for grass has its own production of forests. no doubt, buy them, because the manufacturer took into account all the nuances in advance.
Do not forget about the fact that the fishing line for the trimmer should correspond to all the hardware characteristics of your motorcycles as much as possible so as not to cause its breakdowns.
It is best to buy 2 or 3 slices of fishing line intended for different purposes at once. One type of fishing line will be more effective in mowing fresh young grass, the second. in mowing stiffly overgrown, and the third will help you demolish all the gross.

When you have already bought a certain type of fishing line, be sure to follow the tips for its operation from the manufacturer. Thus, if you use a thread for young grass for dry.resistant, it will get out of the working condition very quickly, and you will have to buy a new one and replace it again.

How to put, wind and change a fishing line for a trimmer?

To do everything correctly and neatly, prepare a separate cut of the fishing line about 4 meters. The length may vary depending on the characteristics of your thread and the lawn mower itself. To find out how much fishing line you need, you can perform the following simple action: inside the coil, wrap the equipment to such an extent that it and the side protrusion of the coil are equal. At the same time, the equipment should not go out for the side ledges. What happened is the length you need, now you can make refueling. The length of the segment also depends on the thickness of the fishing line. the thinner it is, the more it needs, the thicker, the less.

Here is a step.by.step instruction on how to correctly refuel the equipment into the tip of your unit.

Then you need to take the second end on the other side and go too far. Gently approach him, while ensuring that the retreat is 15 cm.
Now you need to find out the direction in which you will wind the fishing line for the trimmer. Ignoring or incorrect execution of this item can lead to your trimmer for grass or lawn mower will not function normally. Inspect the surface of the coil to find out the right direction. In 99% of the coils, an arrow is drawn there, which shows the desired direction.
Instead of the gun-wiring pointer, there may be a letter designation (for example, Wind Line), which also indicates the direction. If you are not lucky, and there is no pointer on the coil, it will definitely be on the head. On each head, the direction of its movement is drawn, respectively, you need to wind in the opposite direction from what is indicated on the head.
After you have determined the direction of winding, proceed to the process itself. It is necessary to gently wind up (refill) thread on the corresponding grooves-undergraduates. Inside each end there is its own groove, do not forget to follow it. If suddenly they are not, put the equipment in the proper distribution order.
Follow the moment when almost the entire thread will be wound. When this happens, place in the side wall (special opening) the part of the part in which the protrusion is 10-15 cm, and then repeat this action with the second end, putting it on the opposite side.
Place the drum in its place, and then pull the ends of the thread, thereby taking them out of the walls of the coil. Now you can place the lid in your place.

The process of winding the fishing line on a motorcycle or a trimmer for grass is completed, now cut the ends of the thread, if suddenly their size does not suit you (or you were just mistaken in measurements). You can put on the drum already completely assembled on your unit. Now it can be used. Even a beginner can install a new fishing line for a trimmer on your device, this rarely causes difficulties.

If you are guided by all the advice presented, it will be as simple for you as mowing grass.

Sources:

https://agrohimtrans.ru/gazonokosilki/namotka-leski-na-katushku-trimmera.html
https://technorama.ru/info-baza/kak-namotat-lesku-na-katushku-trimmera.html
https://proinstrumentinfo.ru/kak-zapravit-lesku-v-katushku-trimmera-pravilno-video/
https://stroy-podskazka.ru/trimmery/namotat-lesku-patriot/
https://tokar.guru/stanki-i-oborudovanie/trimmery-gazonokosilki-motokosy/kak-namotat-lesku-na-katushku-trimmera-sposoby-namatyvaniya-i-video.html
https://lesparksad.ru/blog/kak-namotat-lesku-na-trimmer
https://hitech-online.ru/tehnika-dlya-sada/trimmer/kak-menyat-lesku.html
https://stroy-podskazka.ru/gazonokosilki/leska/
https://stroy-podskazka.ru/trimmery/leski-dlya-benzinovyh/

Grass Trimmer cord, fishing, line, motorcycle, trimmer