How to hang a trimmer for grass on the wall correctly. Storage rules for electric trimmers

trimmer for grass in the garage how to hang

Hi all! I was faced with such a problem, I have nowhere to attach a lawn mower in the garage, and I don’t want to drag it to the attic because I use it just every 2-3 months, and now I want such an ideas that I want to share with you. Necessary details:-2 rails 1 m long-1 self-tapping screw 25-35 cm long-10 screws 3.5x45mm and.

To store the lawn mower on the wall, a suspension of two metal plates was made, about 50 cm long. Each. The lawn mower lay on the floor and specifically on the “place” of the strip bent. The stripes are connected by a bolt. The suspension itself is fixed on the wall with two anchor bolts. On the upper ends of the stripes were worn by tubes, the ends of which were pulled away by exhaust rivets through the washers. Two pieces cut for putting on a rubber hose and wrapped with island are installed on the handle of the lawn mower. A rubber plate is fixed on the wall to prevent damage to the gas mowing tank against the wall.

How to store a benzotrimer

I was faced with such a problem, I have nowhere to attach a lawn mower in the garage, and I don’t want to drag it to the attic because I use it just every 2-3 months, and now I want such an ideas that I want to share with you. Necessary details:-2 rails 1 m long-1 self-tapping screw 25-35 cm long-10 self-tapping screws 3.5x45mm and I have a stupid chain with hooks to the ceiling and everything. Brought, hanged and let it hangs. And so, too. 7.

Place for a trimmer’s lawmaker for grass

Hi all!I was faced with such a problem, I have nowhere to attach a lawn mower in the garage, and I don’t want to drag it to the attic because I use it just every 2-3 months, and now I want such an ideas that I want to share with you.Necessary details:-2 rails 1 m long-1 self-tapping screw 25-35 cm long-10 screws 3.5x45mmy wish for good luck!

Комментарии и мнения владельцев 32

Log in or register to write Комментарии и мнения владельцев, ask questions and participate in the discussion.

The case would have to be put on it, otherwise it will gather dust in the offseason

I have gasoline in a spit all winter. of course, I can, of course, can win 300 but in the spring and there are no problems. if he remained not to merge him? This is already waste.And the idea of ​​a cool one must also attach such a type of one, otherwise it is also lying around. though I have a collapsible but still interferes in the garage.

Boiled.I opened the link because it became interesting how to store a trimmer for the grass. It turns out it’s just a shelf under the ceiling.I have a wooden staircase. I rarely use it. For storage, I made two hooks under the ceiling. I wonder how I keep the stairs?For storing trash, I built a rack from the boards along the wall.Когда хлама стало больше, вдоль второй стенки Соорудил стеллаж из стоечного профиля 50. I put the trash in the boxes, on the floor are severity. Someone is interested in how I keep the rubbish and my ‘make’? I don’t think.Or the washer tank 2108, which I pinned to the garage gate and my hands.

I expect in the near future a detailed post about a self.tapping screw on which you can hold a working robe or keys. I urge everyone to lay out real crafts that really help out.

I also have the 25th Olechka, I recently bought.And you can hang horizontally? VVS-Razan. View profile. User messages. Private message. Registration: 06.09.2007 Ryazan Posts: 1130. It may be possible, but with another suspension design.

But the whole question is that gasoline does not flow.

Trimer storage. Hook for motorcycles (trimmer for grass).

With a trimmer, you need to be able to not only correctly contact, but also store it correctly. Often owners of garden equipment, without thinking about the properties of benzo- or electric ships, simply throw the tool into the pantry and lock them on the castle. Under such conditions, there is a chance that the trimmer for the grass will break.

It is best to store motorcycles in limbo. Under a motorcycle or trimmers for grass, we mean a bar with a motor mounted on it and a mowing head with a fishing line. The GSH23 hook is specially designed for storing an electric, battery and gasoline trimmer for grass in an suspended vertical position.

Fastening for gasoline trimmer for grass

The rubberized holders reliably and carefully support the engine of the trimmer for the grass, the mowing head is below. Depending on the size of the trimmer for the grass, the hook is attached at a height that allows you to place the tool in limbo. In this position, your tool will be easily and quickly available at the right time, while occupying the minmal space in the utility room.

The reinforced hook GSH23 is also convenient for storing another heavy overall tool, garden equipment and inventory: chainsaws, bush cutter, electric drill.

Mounted on a steel rail attached to the wall. Recommended load up to 30 kg.

Manufacturer: Kenovo manufactoring Co., Ltd. Address: N.99-8, Furong Zhongsan Road, Xishan Economic Development Zone, Wuxi, Jiangsu, China. Made in China.Importer: Private Enterprise “Kenovo”. RB, g. Minsk, st. Kamennorskaya, house 47, office 78.

UNP 192192377 is subject to mandatory confirmation of compliance.Production date: June 2014.The warranty period has not been set.Shelf-life Unlimited.

Trimmer care in winter and preparing a trimmer for grass for spring

Preparing a trimmer for grass and preparing a chainsaw for winter storage:

  • Get a bit / finish everything you need to get a bit (at the same time, you use the fuel so that there is no stay for winter storage in a trimmer or for storage in a chainsaw).
  • Remove the tank plug, turn the trimmer for grass (chainsaw) and drain all the fuel from the tank into the tank for technical use (a canister or a bottle with a funnel for washing engine parts for maintenance). This is the main thing in preparing a trimmer for grass and preparing a chainsaw for winter storage.Get a trimmer for grass / chainsaw and develop the remains of fuel from the carburetor until it stalls (if you leave the fuel in the system, then after a while the fuel is delayed and oxides and tarry deposits are formed in the carburetor channels, which will interfere with the normal operation of the engine after winter storage).
  • Be sure to wash everything with warm water and brush on the steering wheel, everything is on the rod and both protection of the trimmer for the grass, and make full care for the trimmer. add the lubricant to the gearbox, remove the knife, clean the leash cartridge inside, inspect everything on the gas tanks for the presence of cracks, bent, bent, bent scuffs, distortions, gaps (in the same way you need to make care of a chainsaw). Then, to store a trimmer for grass and storage of a chainsaw, do T.about. air filter, partial disassembly of the motor, washing and purging, lubricating the moving parts, inspect the clutch condition and make an accurate adjustment of the carburetor of the trimmer for grass.
  • Preparing a trimmer for grass and preparing a chainsaw for winter storage. unscrew the spark plug, bring the piston to the upper dead point (starter), pour 20 g into the candle hole 20 g. motor oil and slowly several times cranct with a starter to grease the cylinder.piston group. Set the spark plug in place (no need to tighten).Trimmer care and care for a chainsaw during winter storage. once a month, it is advisable to remove the candle and make several crankshaft revolutions to update the lubricant in the cylinder.
  • Wrap the engine of the trimmer for grass and chainsaws in a rag or bag so that in winter the temperature changes when condensation forms, moisture does not get into the engine of the lawn mower.

How to prepare a trimmer for grass for spring operation

You carefully looked after your lawn. you aeration, sowed, fed fertilizers Now you are waiting. Waiting for warm days and blue sky, and you know for sure that the grass will be green soon. You checked the list of what you need to do for the lawn. And your trimmer is ready for the grass? You know how to prepare a trimmer for grass?

Your tool in the barn is configured and ready for the new season of the kosba? Let’s look at the list of what you need to do for a regular trimmer for grass, so that it is ready to do your job well (mow).

How to prepare fuel for a trimmer for grass

The trimmer engine for grass will work better and will be better ready for kosbe, if you add a fuel stabilizer (additive) to the fuel mixture. Before long storage, do not forget to drain all fuel. Then get the engine and let it work until it stalls, so that there is no fuel in the fuel system.

When the seasoning time comes for the new season, it is very important to use a previously properly prepared mixture of oil and gasoline. This will ensure the proper performance of the 2-stroke engine of the trimmer for grass. Pre.prepared fuel eliminates the troubles and errors when mixing fuel immediately before the mowing. It is necessary to mix fuel so much to use it for a month, no longer, since when stored more than 1 month, oil precipitates and fuel ages.

How to prepare a trimmer engine for grass

Before the start of the season, you need to replace the spark plug of trimmer for grass, fuel filter, clean the air filter and adjust the carburetor. This will reduce fuel consumption and increase power. For a trimmer for grass with a 4-stroke engine, you need to check the level of motor oil and its freshness, as well as replace the oil filter.

How to prepare a fishing line for a trimmer for a trimmer for grass

Lines for a trimmer, with long.term storage (for example, after winter storage), can become dry and brittle. To prevent this and increase the service life of your fishing line, you just need to store it in a sealed bag with a small amount of water. And before starting operation (before charging a fishing line for a trimmer into a trimmer head), it is advisable to soak a fishing line for a trimmer for several days in water. Then she (a fishing line for a trimmer) will become more elastic and durable.

Technology for creating a wooden tool for tools in a garage with your own hands

Before creating a rack for storage with your own hands, you need to decide on the total number of tools that must be placed.

Project creation are important points

In order for the wall system to be convenient, they make up a plan of the future design on paper, where all requirements for the system are taken into account:

  • Calculate the height and width of the rack. it is better to use completely the entire wall from the bottom to the top.
  • The recommended depth of niches for the rack is up to 65 cm, and the width between the vertical supports of the shelves is up to 1 m.
  • The required number of shelves is determined, including how many shelves will be with a toolwall for a tool.
  • Below are floor spacious shelves and racks for tires, wheels and for a large carpentry tool.
  • Design places for magnetic ribbons, hooks, holders.
  • Calculate how many organizers and containers are required, what size, and also determine their location.
  • Sort the tool and all small fasteners and parts for storage.

What will be needed

Tools are prepared for the manufacture of a rack:

In shelves and containers, it is recommended to drill holes for natural ventilation. This is necessary to protect objects from rust.

What materials need to be prepared

All necessary material for creating a rack is prepared, according to the designed project:

  • For the main panel of the holder, you can use the peopanel.
  • If the rack is made of wood, it is recommended to purchase lumber from oak or pine without cracks, knots.
  • Wooden boards up to 2.5 cm thick are required for shelves.
  • Shelves can be made from plywood for ordinary and laminated.
  • The vertical racks of the frame are made from a timber 10 × 10 cm.
  • Wooden boards are previously recommended to treat with mold and fungus with products, paint.
  • For assembling a metal frame, a rectangular profile and corners (up to 2 cm) is required.

The manufacture of components

The manufacturing procedure for the rack and components is as follows:

  • On the specified sizes, vertical racks from a beam and boards or plywood on shelves are cut, prepared by a peopanel. Set up places for shelves.
  • For the manufacture of a metal frame, the corner grinding of the desired height is cut and the location of the shelves is planned. Collect the frame using fasteners, corners. Apply a primer, then cover the parts with anti.corrosion paint.
  • Shelves are collected from boards. They are tightly pressed against each other and chopped with nails or self.tapping screws.
  • The shelves from the boards are collected, laying the elements across the frame, so they can withstand the great weight. If the shelves are assembled by laying the boards along the frame, that is, the probability that they will bend under the weight of the tools.
  • The design is assembled using self.tapping screws, nails and glue for wood.
  • The joints of all parts are additionally strengthened with metal corners.
  • The entire structure is installed to the wall and fixed with metal brackets.
  • Separately made in the required number of shelf with cuts, holders, magnetic tapes, racks, containers and organizers.
  • You may need a small desktop with a vice of wooden boards. It can be attached to the wall system in the form of a stationary or folding surface on metal or wooden holders.

Assembly of the structure

First, the rack frame is assembled, then wooden shelves are attached to it with self.tapping screws. The shelves of the rack are filled with retractable baskets, organizers, containers and other holders. Hooks, magnets and magnetic tapes are attached to the onpanel. They place tools on them. For convenient fastening of the pliers, the mount in the form of the crossbar is installed on the peopanel. Containers are filled with small fasteners, tools. Garden inventory, bicycles, tires and wheels, skis, skates and sledges are hung on holders or racks, or placed on containers.

Processing and painting of the finished product

The finished rack is once again processed from mold, the ends are painted in several layers with paint. Containers and organizers can be painted in the same color as the rack itself.

Most often, a workshop or garage does not look in the best way due to cluteness. But thanks to the creation of a wall.mounted system for storing tools in the form of racks, all the necessary items, fasteners, inventory will be competently sorted and placed. The room will acquire a neat look, and all the work can be performed quickly and without delay.

TOP of the best ideas for storing tools

Since the tools are long and short, large and small, different in shape, then the ways of their storage differ. There are several techniques for systematizing tools. Below are the most convenient and popular of those that can be made with your own hands right on the wall.

Vertical storage systems of type rack

One of the varieties of vertical storage of tools is a system in the form of racks. On racks, you should arrange the most necessary tools that can be placed in close availability. Items that are required less often are cleaned on long.range racks on the upper or lower shelves. Metal shelves for garage. IF systems. are perfect for this.

But even with a large selection of options, the proposal will not always satisfy the necessary requests of the owner of the garage. Therefore, it is recommended to combine purchased racks with holders and regiments made by yourself, or completely construct yourself a wall.wall storage system.

Vertical home.made wood racks with slots for storing wrench and screwdrivers are very convenient. On them you can easily place the bushings for attaching the tool with a conical shank of different sizes or pliers.

Vertical rack in the form of a mobile stand. a great choice for placing an improvised tool. It is recommended to make it from wood or plywood. Separate groups of tools are located on hooks, magnets or shelves. Often use special peopanels for the vertical storage system.

Magnetic tape

The magnetic tape is simple and convenient to use. Magnetic stripes are taken for attaching the tool and mounted on a wall storage system. The most different tools can be attached to the tape: from small metal wings and screwdrivers to large objects.

Plastic containers

You can easily organize the storage of even the smallest items by collecting a system of small containers. You can store them:

The most affordable way is plastic bottles of different sizes or plastic containers, as well as small glass jars. The containers can be placed on the vertical system by shelves or attached directly to the wall to save space.

Plastic opaque canists with a cut off are also suitable. If desired, they can be signed or numbered.

Organizers

For storing small details and objects, you can easily construct an organizer with your own hands:

  • Take any box from an old unnecessary table and make a lot of small partitions inside it from cardboard or plywood. Thanks to individual cells, all small necessary details will always be in their place, sorted by the configuration.
  • If you make an organizer yourself, you need to take a piece of polystyrene. it will be the bottom of the organizer, and for walls and partitions. PVC (glue it with glue to the bottom), for the lid you can use transparent plastic or glass.
  • Simple and quickly you can make an organizer for screwdrivers. It can be made according to the instructions, as in p. 1 or 2. And you can drill the holes of the desired diameters in a bars of wood or foam, then attach it to the wall and insert it into the holes of the screwdriver. All objects will be in sight and will not be lost.
  • Another version of the organizer is assembled from cans of different sizes. Tins women are quickly and firmly attached to the vertical wall in any convenient position and are filled with either small details or tools.

Garden tool

Garden tool always takes up a lot of space, clutches the passages. This can be avoided if you choose one of the walls of the garage or workshop and convert it for storage of garden inventory. It is recommended to use ordinary pipes from PVC to create a storage system, make holders in size of garden inventory and other things:

There are very simple options for fixing the tool in the garage:

  • Sad inventory racks. They are made of ordinary wooden pallets. It is leaned by the bottom against the wall and fixed with self.tapping screws, they are nailed to any sizes of the rail.
  • Another simple way is the usual strong and reliable wooden or metal hooks along the entire wall, where you can hang inventory, extension cords of different sizes. Stronger brackets and shelves can be used to store wheels, tires, inflatable boat.

Storage of garden and working inventory and other things using a wall system and racks is convenient and is popular.

Technology for creating a wooden tool for tools in a garage with your own hands

Before creating a rack for storage with your own hands, you need to decide on the total number of tools that must be placed.

Project creation are important points

In order for the wall system to be convenient, they make up a plan of the future design on paper, where all requirements for the system are taken into account:

  • Calculate the height and width of the rack. it is better to use completely the entire wall from the bottom to the top.
  • The recommended depth of niches for the rack is up to 65 cm, and the width between the vertical supports of the shelves is up to 1 m.
  • The required number of shelves is determined, including how many shelves will be with a toolwall for a tool.
  • Below are floor spacious shelves and racks for tires, wheels and for a large carpentry tool.
  • Design places for magnetic ribbons, hooks, holders.
  • Calculate how many organizers and containers are required, what size, and also determine their location.
  • Sort the tool and all small fasteners and parts for storage.

What will be needed

Tools are prepared for the manufacture of a rack:

In shelves and containers, it is recommended to drill holes for natural ventilation. This is necessary to protect objects from rust.

What materials need to be prepared

All necessary material for creating a rack is prepared, according to the designed project:

  • For the main panel of the holder, you can use the peopanel.
  • If the rack is made of wood, it is recommended to purchase lumber from oak or pine without cracks, knots.
  • Wooden boards up to 2.5 cm thick are required for shelves.
  • Shelves can be made from plywood for ordinary and laminated.
  • The vertical racks of the frame are made from a timber 10 × 10 cm.
  • Wooden boards are previously recommended to treat with mold and fungus with products, paint.
  • For assembling a metal frame, a rectangular profile and corners (up to 2 cm) is required.

The manufacture of components

The manufacturing procedure for the rack and components is as follows:

  • On the specified sizes, vertical racks from a beam and boards or plywood on shelves are cut, prepared by a peopanel. Set up places for shelves.
  • For the manufacture of a metal frame, the corner grinding of the desired height is cut and the location of the shelves is planned. Collect the frame using fasteners, corners. Apply a primer, then cover the parts with anti.corrosion paint.
  • Shelves are collected from boards. They are tightly pressed against each other and chopped with nails or self.tapping screws.
  • The shelves from the boards are collected, laying the elements across the frame, so they can withstand the great weight. If the shelves are assembled by laying the boards along the frame, that is, the probability that they will bend under the weight of the tools.
  • The design is assembled using self.tapping screws, nails and glue for wood.
  • The joints of all parts are additionally strengthened with metal corners.
  • The entire structure is installed to the wall and fixed with metal brackets.
  • Separately made in the required number of shelf with cuts, holders, magnetic tapes, racks, containers and organizers.
  • You may need a small desktop with a vice of wooden boards. It can be attached to the wall system in the form of a stationary or folding surface on metal or wooden holders.

Assembly of the structure

First, the rack frame is assembled, then wooden shelves are attached to it with self.tapping screws. The shelves of the rack are filled with retractable baskets, organizers, containers and other holders. Hooks, magnets and magnetic tapes are attached to the onpanel. They place tools on them. For convenient fastening of the pliers, the mount in the form of the crossbar is installed on the peopanel. Containers are filled with small fasteners, tools. Garden inventory, bicycles, tires and wheels, skis, skates and sledges are hung on holders or racks, or placed on containers.

Processing and painting of the finished product

The finished rack is once again processed from mold, the ends are painted in several layers with paint. Containers and organizers can be painted in the same color as the rack itself.

Most often, a workshop or garage does not look in the best way due to cluteness. But thanks to the creation of a wall.mounted system for storing tools in the form of racks, all the necessary items, fasteners, inventory will be competently sorted and placed. The room will acquire a neat look, and all the work can be performed quickly and without delay.

How to use a trimmer for grass for vertical haircuts?

Trammers for grass are used for pruning weeds in hard.to.reach places and haircuts of lawns. The cutting head of this garden inventory is located horizontally, which makes it convenient horizontal cutting of vegetation. But sooner or later each gardener has a problem with the leaves of the bushes or with the edges of the lawns. Here a trimmer for the grass will have to be used differently, turning it vertically.

Instructions for the vertical use of a trimmer for grass.

1) Point the protective glasses, since with a horizontal haircut, the probability of trimming of grass and leaves in the eyes of the operator trimmer for grass is very high. It will also be good to throw a belt that will fix the position of the trimmer for the grass relative to the body. This will not allow the tool to break out of the hands and fall. Next, carefully turn on the trimmer for the grass according to the original instructions from the manufacturer, holding a trimmer for the grass horizontally.

2) Keep a trimmer for the grass hard, by the handle, near which the gas solar is located. Then carefully turn the trimmer for the grass by 90 degrees. so that the cutting head of the tool is not parallel to the ground, but perpendicular.

3) Next, you need to take up the bar or a special handle on the bar. Then raise and lower the trimmer several times for the grass up and down, checking the balance, and looking for the desired angle of inclination of the cutting head.

hang, trimmer, grass, wall, correctly, storage

Weed eater string trimmer storage for under 5. Are Jay the redneck building a cheap easy shelf rack

4) take a place for the vegetation section that you are going to cut. If this is the foliage of a tree or a bush, you should not get too close. If this is the edge of the lawn or hedge, it is worth it to come almost close. Raise the head of the trimmer for the grass to the level just higher than the haircut level.

5) Now, when all the preparations are completed, click on the gas lever that will drive the cutting head. Adjust the position of the trimmer for grass in the space relative to the place of the haircut, see how the slice will go. On the basis of this, orient yourself and get to work.

When a trimmer for grass cuts the stems or foliage vertically, trims fly not near the ground, but up and down, so work without protective glasses or masks becomes not only difficult, but almost impossible. When working with a benzotrimmer, you need to ensure that the fuel tank is closed hermetically, otherwise the fuel can result in. If a vertical haircut is carried out by an electrimmer, it is necessary to monitor the wire. it can easily get under the blades of the cutting head, if the protective grill is removed from it. Here, either the wire will cut it down, or the head of the trimmer for the grass will break. In general, there are no special requirements for the trimmer with vertical cutting cutting.

However, we recall that not every trimmer can cut rude branches. Light batteries and electric trimmers for grass most often when branches or wood chips fall under a fishing line for a trimmer on a cutting head, break. The fishing line for the trimmer is confused or torn, and it has to be changed to a new. By the way, this is a simple process. Worse, if the mechanism of rotation of the fishing line is violated. Then you cannot avoid going to the repair workshop and significant money expenses.

recently, in 2011, the concept of a vertical trimmer for grass was invented, which is designed specifically for cutting trees. According to development from English scientists, a trimmer for grass cuts young branches, forming a crown of plants. Such a haircut for fruit trees is very useful, since when the number of branches is reduced more than vital juices, it goes into the fruits.

So far, it is difficult to get such trimmers for grass, and you have to use ordinary, more powerful. Most often, we use motorcycles (benzotrimers) with interchangeable nozzles for vertical trimming.

Wall.mounted tools for storing tools

A lot of different tools, inventory have been collected in the garage or workshop. If you do not think through the storage system, then finding the desired item is not so easy. To put the perfect order in the garage and save the time spent on the search for a particular tool, you need to collect all the necessary items in one convenient zone. For this, the tool attaching the tool on the wall is ideal. Thanks to this location of the tools in the room, the useful area is released, the useful area is released. All the necessary devices are placed in sight.

TOP of the best ideas for storing tools

Since the tools are long and short, large and small, different in shape, then the ways of their storage differ. There are several techniques for systematizing tools. Below are the most convenient and popular of those that can be made with your own hands right on the wall.

Vertical storage systems of type rack

One of the varieties of vertical storage of tools is a system in the form of racks. On racks, you should arrange the most necessary tools that can be placed in close availability. Items that are required less often are cleaned on long.range racks on the upper or lower shelves. Metal shelves for garage. IF systems. are perfect for this.

But even with a large selection of options, the proposal will not always satisfy the necessary requests of the owner of the garage. Therefore, it is recommended to combine purchased racks with holders and regiments made by yourself, or completely construct yourself a wall.wall storage system.

Vertical home.made wood racks with slots for storing wrench and screwdrivers are very convenient. On them you can easily place the bushings for attaching the tool with a conical shank of different sizes or pliers.

Vertical rack in the form of a mobile stand. a great choice for placing an improvised tool. It is recommended to make it from wood or plywood. Separate groups of tools are located on hooks, magnets or shelves. Often use special peopanels for the vertical storage system.

Magnetic tape

The magnetic tape is simple and convenient to use. Magnetic stripes are taken for attaching the tool and mounted on a wall storage system. The most different tools can be attached to the tape: from small metal wings and screwdrivers to large objects.

Plastic containers

You can easily organize the storage of even the smallest items by collecting a system of small containers. You can store them:

The most affordable way is plastic bottles of different sizes or plastic containers, as well as small glass jars. The containers can be placed on the vertical system by shelves or attached directly to the wall to save space.

Plastic opaque canists with a cut off are also suitable. If desired, they can be signed or numbered.

Organizers

For storing small details and objects, you can easily construct an organizer with your own hands:

  • Take any box from an old unnecessary table and make a lot of small partitions inside it from cardboard or plywood. Thanks to individual cells, all small necessary details will always be in their place, sorted by the configuration.
  • If you make an organizer yourself, you need to take a piece of polystyrene. it will be the bottom of the organizer, and for walls and partitions. PVC (glue it with glue to the bottom), for the lid you can use transparent plastic or glass.
  • Simple and quickly you can make an organizer for screwdrivers. It can be made according to the instructions, as in p. 1 or 2. And you can drill the holes of the desired diameters in a bars of wood or foam, then attach it to the wall and insert it into the holes of the screwdriver. All objects will be in sight and will not be lost.
  • Another version of the organizer is assembled from cans of different sizes. Tins women are quickly and firmly attached to the vertical wall in any convenient position and are filled with either small details or tools.

Garden tool

Garden tool always takes up a lot of space, clutches the passages. This can be avoided if you choose one of the walls of the garage or workshop and convert it for storage of garden inventory. It is recommended to use ordinary pipes from PVC to create a storage system, make holders in size of garden inventory and other things:

There are very simple options for fixing the tool in the garage:

hang, trimmer, grass, wall, correctly, storage
  • Sad inventory racks. They are made of ordinary wooden pallets. It is leaned by the bottom against the wall and fixed with self.tapping screws, they are nailed to any sizes of the rail.
  • Another simple way is the usual strong and reliable wooden or metal hooks along the entire wall, where you can hang inventory, extension cords of different sizes. Stronger brackets and shelves can be used to store wheels, tires, inflatable boat.

Wall.mushrooms of lawn mowing for storage.

To store the lawn mower on the wall, a suspension of two metal plates was made, about 50 cm long. Each. The lawn mower lay on the floor and specifically on the “place” of the strip bent. The stripes are connected by a bolt. The suspension itself is fixed on the wall with two anchor bolts. On the upper ends of the stripes were worn by tubes, the ends of which were pulled away by exhaust rivets through the washers. Two pieces cut for putting on a rubber hose and wrapped with island are installed on the handle of the lawn mower. A rubber plate is fixed on the wall to prevent damage to the gas mowing tank against the wall.

Sooner or later, the season ends, trimmers for grass and other equipment go to long.term storage to the far corner. In order to use the tool next year without problems, it is necessary to perform several simple manipulations, so to speak, to preserve a gasoline trimmer for grass.

And storage in a room with constant temperature and normalized humidity will help to save some bearings. Lubrication and cleaning of some elements are also necessary. For storage, it is better to use heated rooms: warm garage, pantry or insulated balcony.

Drain the fuel

Since trimmers for grass mainly have a two.stroke engine, it is refueling accordingly with a mixture of gasoline and oil. Such a solution over time begins to decompose with the displacement of the resinchy sediment, which in turn clogs all possible fuel channels. Therefore, the solution must be completely drained and removed from the carburetor, pure gasoline can be poured and pumped with rubber pumping. So that pure gasoline would remain in the carburetor, t.to. dry carburetor is also bad.

Lubrication of the piston group

If you store the braid in the country in the barn or another frozen and thawed room, we recommend that you unscrew the candle and add a little oil to the cylinder, twist the lubricant starter. Then put the piston in the upper dead point to close the inlet and release window, screw the candle back. Thus, the cylinder, piston and rings will be lubricated, which will prevent the appearance of rust and sticking rings. Try not to spoil the candle thread, it can also be lubricated.

External cleaning of dirt

We recommend that before storage, clean the trimmer for grass from dirt: go through a damp cloth, slide down the dried clots of the grass, unscrew the head and clean there too. The tool should be in a clean and well.groomed state. Well launderes grass launders for washing windows from m alcohol or ammonia. Be sure to clean the ribs of the air intake and the engine air filter so as not to return to this at the beginning of the season.

The structure of the gasoline trimmer for the grass is simple and does not require supercomplicated intervention, and several simple conservation work will help you start and work your trimmer in the upcoming season.

hang, trimmer, grass, wall, correctly, storage

Do I need to prepare gasoline garden equipment for the winter period?

This question is in many aspects controversial. A considerable number of gardeners are of the opinion that branded garden equipment, when using high-quality fuel and lubricants, does not require preparation for winter storage. And in the spring, after the tops and pumping of gasoline or fuel mixture, without any problems will continue its work.

At the same time, the conditions for storing garden equipment are completely different. Someone can afford to store it in a warm room, and someone will lie in the whole winter in a humid and frosty shed. And the concept of “high-quality fuel-lubricants” we have a rather vague.

My opinion is this if you can avoid moisture (dew) when storing a gasoline engine, then the conservation of cylinders and elements of garden equipment for the winter is not required. It will be enough just to drain and develop the remaining gasoline or fuel mixture. The appearance of moisture can be avoided in several ways: store the engine at room temperature, or ensure high.quality thermal insulation of the motor, for example, store in a dense box, upholstered in mineral wool.

Storage of lawn mowers in winter. goals and objectives.

Proper storage of the lawn mower in the winter consists of several preparatory stages. The main of them: Preparing the motor motorcycles for long.term storage in winter. It will prevent pressing the rings in the piston, relieve the consequences of the oil hardening, the condensation of moisture on the internal details of the motor with subsequent corrosion.

  • Clean the gasoline braid from dirt.
  • Pour gasoline or fuel mixture from garden technology and tighten the gas tank cover. I do not recommend, in the future, to use a merged mixture as a fuel for technology. How much can you store the fuel mixture for two.stroke engines read here.
  • We start a lawn mower and wait until at idle revolutions the remains of gasoline in a carburetor, primer and fuel supply are developed. There are not a few residues and the garden will not work for a long time, before stopping, the engine will slightly increase the speed, due to the depletion of the fuel mixture.

Motokosa conservation. engine cylinder processing.

  • Remove the oversight.
  • We unscrew the candle. Check the gap and its general condition.
  • Using the syringe, spray through the candle hole in the cylinder cavity 2-2.5 ml of oil, which is designed to manufacture the fuel mixture of your garden technology. You can use any anti.naking, anti.corrosion agent, ideally, a specialized tool for internal conservation of motor engineering engine.
  • Using a manual starter when the ignition is turned off several times, turn the piston.
  • We twist the candle.
  • We put on the overseer.

Attention. If you accidentally pour oil, and in the spring your garden technique will not want to start

First of all, unscrew and degrease the candle.

Preservation of the lawn mower. processing the carburetor and cleaning the air filter.

  • Remove the air filter lid and the filter itself with a metal mesh, if this is provided by the design of garden equipment.
  • Open the throttle.
  • Inject the anti.corrosion in the carburetor.
  • Rinse and dry air filter. Install it in place.

Preparation of the cutting knife of garden technology for long.term storage.

  • Remove the knife.
  • Clean it from dirt.
  • We process it and seats with an anti.corrosion agent. For savings, you can use any inexpensive machine oil, in t.h. and working out.

Preparation of a mowing coil with a fishing line for winter storage.

  • Remove the mowing head from garden equipment.
  • We disassemble and clean the remains of grass and dirt.
  • Wash a fishing line for a trimmer from a coil.
  • Store a fishing line for a trimmer in a wet place to avoid its drying out and brittle. For example, wrap in a bag with the addition of water.

Advice. If in the spring a spit line for a trimmer still boiled and became fragile, place it for several hours in water. She will partially restore her properties.

If there is time, then do not put off the reducer’s lubrication on the “future”.

Proper storage of the lawn mower during long.term downtime, and even more so in the winter, the conservation of its engine and cutting tools will ensure its uninterrupted operation in the next season. In addition, there are many nerves and money, which, as you know, do not happen much.

Preparing for operation

As with any other technique, in working with the trimmer there are rules. First you need to make sure that the main nodes and assemblies: screw, rods, handles and motor. If the device has not yet been assembled, then it should be correctly assembled according to the instructions.

Gasoline unit

In the case of a gasoline trimmer, it is necessary to check the gearbox for lubrication. Also, do not forget to add lubricants to the fuel tank, if the instruction manual is evidenced. As a rule, gas and oil are mixed in a ratio of 45 to 1, but these indicators may vary depending on the model and manufacturer, so you should carefully study all the technical requirements for the device. The fuel container must be filled on the very neck. If all technical fluids are flooded, then you can try to start the device. But it’s not worth mowing right away, it will be better to let the trimmer work without load so that the engine works to the flooded fuel. A few minutes will be enough, after which you can give the motorcycle full load.

Elektokos

With an electric trimmer, everything is much easier. Having made sure that the gearbox has the required amount of lithol, you can start work. No additional measures are required. Unless it is necessary to make sure that the carrying does not run on the path of mowing in order to avoid possible damage.

When the device itself is ready to work, you should make sure that there is nothing around that could interfere with the work. If possible, the estimated mowing area should be cleaned of snags, glass, stones and other solid objects that can damage a knife or fishing line for a trimmer.

Depending on the upcoming work, you need to choose a nozzle for a trimmer for the grass: a screw-knife for weeds and hay, a fishing line for a trimmer for lawn grass or a disk saw for shrubs. Mowing should be in the opposite direction from people, if possible, moving away from buildings and buildings. You should not get too close to the fence and other designs, since the fishing line for a trimmer can catch on sharp edges, and the screw-knife will bend if it accidentally offends it a hard object.

The preparation of the device itself will not take much time, all modern models of devices are designed to facilitate and simplify their operation, starting to work in the shortest possible time.

Preparing for operation

As with any other technique, in working with the trimmer there are rules. First you need to make sure that the main nodes and assemblies: screw, rods, handles and motor. If the device has not yet been assembled, then it should be correctly assembled according to the instructions.

Gasoline unit

In the case of a gasoline trimmer, it is necessary to check the gearbox for lubrication. Also, do not forget to add lubricants to the fuel tank, if the instruction manual is evidenced. As a rule, gas and oil are mixed in a ratio of 45 to 1, but these indicators may vary depending on the model and manufacturer, so you should carefully study all the technical requirements for the device. The fuel container must be filled on the very neck. If all technical fluids are flooded, then you can try to start the device. But it’s not worth mowing right away, it will be better to let the trimmer work without load so that the engine works to the flooded fuel. A few minutes will be enough, after which you can give the motorcycle full load.

Elektokos

With an electric trimmer, everything is much easier. Having made sure that the gearbox has the required amount of lithol, you can start work. No additional measures are required. Unless it is necessary to make sure that the carrying does not run on the path of mowing in order to avoid possible damage.

When the device itself is ready to work, you should make sure that there is nothing around that could interfere with the work. If possible, the estimated mowing area should be cleaned of snags, glass, stones and other solid objects that can damage a knife or fishing line for a trimmer.

Depending on the upcoming work, you need to choose a nozzle for a trimmer for the grass: a screw-knife for weeds and hay, a fishing line for a trimmer for lawn grass or a disk saw for shrubs. Mowing should be in the opposite direction from people, if possible, moving away from buildings and buildings. You should not get too close to the fence and other designs, since the fishing line for a trimmer can catch on sharp edges, and the screw-knife will bend if it accidentally offends it a hard object.

The preparation of the device itself will not take much time, all modern models of devices are designed to facilitate and simplify their operation, starting to work in the shortest possible time.

Hang a trimmer for grass on the wall

The tariff is valid on weekdays from 9:00 to 18:00. The cost of evening delivery and delivery on weekends and holidays is calculated with a coefficient of 1.5.

Pickup:

You can pick up orders from our showroom (m. Avtozavodskaya).

Delivery to other cities

We send garage storage systems with a transport company (business lines or others at your request). a prepayment of 100%.

Sending by transport companies we carry out weekly.

To process orders, please indicate the email address. with a response letter we will inform you about the cost and conditions of sending the order.

Dates

The order will be shipped within 1-7 days. The manager will inform you of the exact delivery date after the order. To clarify the delivery time before the ordering of the order, you can consult with the manager by phone.

Cash payment

Courier delivery of software and mo. payment for receipt of goods.

Shipment at night. payment for receipt of goods.

Cashless payment

We are set by the account for cashless payment for orders from 5000

Return and exchange

Any mounts, shelves, brackets and suspensions after buying in our store can always be handed over back. To do this, you must independently bring the purchase in the commodity form to our warehouse, or make a return fence with a courier.

Wall.mounted tools for storing tools

A lot of different tools, inventory have been collected in the garage or workshop. If you do not think through the storage system, then finding the desired item is not so easy. To put the perfect order in the garage and save the time spent on the search for a particular tool, you need to collect all the necessary items in one convenient zone. For this, the tool attaching the tool on the wall is ideal. Thanks to this location of the tools in the room, the useful area is released, the useful area is released. All the necessary devices are placed in sight.

TOP of the best ideas for storing tools

Since the tools are long and short, large and small, different in shape, then the ways of their storage differ. There are several techniques for systematizing tools. Below are the most convenient and popular of those that can be made with your own hands right on the wall.

Vertical storage systems of type rack

One of the varieties of vertical storage of tools is a system in the form of racks. On racks, you should arrange the most necessary tools that can be placed in close availability. Items that are required less often are cleaned on long.range racks on the upper or lower shelves. Metal shelves for garage. IF systems. are perfect for this.

But even with a large selection of options, the proposal will not always satisfy the necessary requests of the owner of the garage. Therefore, it is recommended to combine purchased racks with holders and regiments made by yourself, or completely construct yourself a wall.wall storage system.

Vertical home.made wood racks with slots for storing wrench and screwdrivers are very convenient. On them you can easily place the bushings for attaching the tool with a conical shank of different sizes or pliers.

Vertical rack in the form of a mobile stand. a great choice for placing an improvised tool. It is recommended to make it from wood or plywood. Separate groups of tools are located on hooks, magnets or shelves. Often use special peopanels for the vertical storage system.

A quick view of my lawn care equipment storage

Magnetic tape

The magnetic tape is simple and convenient to use. Magnetic stripes are taken for attaching the tool and mounted on a wall storage system. The most different tools can be attached to the tape: from small metal wings and screwdrivers to large objects.

Plastic containers

You can easily organize the storage of even the smallest items by collecting a system of small containers. You can store them:

The most affordable way is plastic bottles of different sizes or plastic containers, as well as small glass jars. The containers can be placed on the vertical system by shelves or attached directly to the wall to save space.

Plastic opaque canists with a cut off are also suitable. If desired, they can be signed or numbered.

Organizers

For storing small details and objects, you can easily construct an organizer with your own hands:

  • Take any box from an old unnecessary table and make a lot of small partitions inside it from cardboard or plywood. Thanks to individual cells, all small necessary details will always be in their place, sorted by the configuration.
  • If you make an organizer yourself, you need to take a piece of polystyrene. it will be the bottom of the organizer, and for walls and partitions. PVC (glue it with glue to the bottom), for the lid you can use transparent plastic or glass.
  • Simple and quickly you can make an organizer for screwdrivers. It can be made according to the instructions, as in p. 1 or 2. And you can drill the holes of the desired diameters in a bars of wood or foam, then attach it to the wall and insert it into the holes of the screwdriver. All objects will be in sight and will not be lost.
  • Another version of the organizer is assembled from cans of different sizes. Tins women are quickly and firmly attached to the vertical wall in any convenient position and are filled with either small details or tools.

Garden tool

Garden tool always takes up a lot of space, clutches the passages. This can be avoided if you choose one of the walls of the garage or workshop and convert it for storage of garden inventory. It is recommended to use ordinary pipes from PVC to create a storage system, make holders in size of garden inventory and other things:

There are very simple options for fixing the tool in the garage:

  • Sad inventory racks. They are made of ordinary wooden pallets. It is leaned by the bottom against the wall and fixed with self.tapping screws, they are nailed to any sizes of the rail.
  • Another simple way is the usual strong and reliable wooden or metal hooks along the entire wall, where you can hang inventory, extension cords of different sizes. Stronger brackets and shelves can be used to store wheels, tires, inflatable boat.