How to make wire twisting with a screwdriver.

Twisting device for twisting wires: 2 simple devices for quick and high.Quality twisting

Due to loose twisting and poor poking, the wires are oxidized and the contact between them is disturbed. Over time, the twisting place begins to gradually heat up, which can lead to a fire of the wiring. In order for the connection to be durable, reliable and safe, we will make simple life hacks, with which you can perform a tight twisting wires and high.Quality poking, regardless of your qualifications, as an electrician.

Wire tape

• Steel hairpin;
• Metal clamp on bolts;
• End tip for crimping the cable;
• Set of nuts;
• Pieces of solder;
• Rosin.

In the work on the home.Made, we use: grinding locksmiths, gas burner, pliers, drill with a cutting disk and a wrench. Clamp the hairpin in a vice and heat the protruding part with a flame of a gas burner until the metal is softened.

Then, without losing a second, with the help of pliers we bend the end of the hairpin under 90 degrees.

Shorten the hairpin using a grinder with a cutting disk. For further use, we leave part with the bent end.We disassemble the clamp and leave one half.Ring with an outer nut.

We clamp it by the ears in a vice and straighten them with a hammer, making the ends of the half.Ring and parallel to each other.

We put on the modified half.Ring with a nut down to the end of the nozzle of the gas burner and fix it using a bolt connection.

In the outer nut of the half.Ring, screw the screwed end of the hairpin and direct its rod along the longitudinal axis of the nozzle of the burner.

We screw the nut on the hairpin, then install the end tip and clamp it with the second nut so that it is located vertically, and its cylindrical part is approximately at the level of the center of the nozzle of the gas burner.

We connect a gas can be connected to a modernized gas burner and turn it on. When the tip is warm enough, we lower pieces of solder into it and wait.

We lower the wire twist into a jar of rosin and immerse in a molten solder for a few seconds. The quality of the puddle in this case is invariably excellent.

Wire twisting

We insert the bolt into the central opening of the washer, on the puck, put a grover puck on the bolt and tighten with a self.Ending nut.

009: TWISTING WIRE EASILY AND QUICKLY!

We clamp the free end of the bolt rod in the drill cartridge and we can assume that our device for twisting the wires is ready to work.

We insert the ends of the wire bent in half into the puck diametrically opposite, holding it behind the bend with pliers, and turn on the drill.

The wires carried away by the puck are twisted into a dense “pigtail”.

In this way, you can twist three and four veins. We bite off unwinded ends with nippers or pliers.

Multi.Dwelling wires

Twisting multi.Core electric wires can be performed in different ways.

Parallel twisting

The simplest method is parallel twisting, when both cleaned wires of the cross on the cross are applied to each other at the place of cleaning of the insulation and at the same time twisted. This compound gives reliable contact, but it will poorly transfer the applied force to the gap and vibration.

This method is best used for copper wires, when one of them is monolithic and the other multi.Core performance. The monolithic wire must be cleaned from the insulation slightly larger than the multi.Core. After twisting from the remaining copper monolithic tail, an additional bend is made in the direction of the twist, due to this, the compound is more reliable. This method is also suitable for twisting aluminum conductors with a different section.

The advantage of parallel twisting is that it can be used to connect at the same time more than two wires.

Consistent twist

In the sequential method, each connected wiring is hung on another. Reliability and contact of such a compound will be optimal, but this twist can only be used for two wires, no more.

Statched veins put the cross on the cross on each other approximately in the middle of the spanned area and begin to tighten. One wire costs around another wire, like the second wire, wind up around the first.

Bandal twisting

You can connect multi.Core wires with each other by bandit twisting. In this case, the combined veins are cleaned on the same length and applied parallel to each other. In this position, they are fixed by the third wire, which is tightly wound on the bare surface of the connected cores.

Please note that using such twisting, you can connect hard multi.Core wires, but you must use the wire soft (flexible) as a fixing). The denser you make a fixing wire, the more reliable the contact connection will be obtained

With the help of a bandage twist, more than two conductors can be connected.

Twisting copper and aluminum wires

You cannot interconnect copper and aluminum directly. However, in many houses, aluminum wires have been carried out, which must be connected to copper, and twisting is sometimes the only way to connect

In this case, it is important to adhere to certain rules that will allow such a consolidation the maximum term

To begin with, it is worth noting that the conductors need to be hardened with each other qualitatively. If their diameter is a significant value, there should be at least 3 turns, and if the diameter is up to 1 mm, in this case it will be necessary to wrap the wire with each other more than five times to ensure a high.Quality transmission of the electric flow

Also, after that it is very important to process the bare surface with special varnish, which has the properties of resistance to water and moisture. When connecting a copper and aluminum wire, it is better to use a special steel plate placed between them. This will avoid their direct contact

Thus, the service life of such a connection will be much more. If there is no such component part at hand, then you can resort to processing copper bare wiring with solder, which will also avoid mechanical contacts of these two metals. An ideal solution to the connection of the copper and aluminum conductor is preliminary application to copper core solder. Especially such preliminary processing is often used when connecting a single and multi-core wire, when in this way the wire consisting of several conductors turns into one-cereal.

Compound isolation

An important requirement in the compound procedure is their isolation in order to avoid accidents. The insulation materials include:

Wire insulation methods directly depend on the material that is used. They are divided into methods such as planting, winding and warming up. In the first case, the material is planted on the twisted segment. In the second. Simple winding is performed with an insulating tape. In the third. Isolation of the heat.Assigned tube provides for its planting on the current.Pissing part with its subsequent warming.

To the question of newcomers “Is it possible to isolate wires with electrical tape?»It should be answered unambiguously positively. This is one of the most common methods. The main requirement is compliance with the shelf life of the material and the lack of visible damage.

Despite the fact that at first glance the procedure for twisting electrical conductive cores seems simple, a responsible approach is required to the case.

Types of twists

There are several ways to perform twisting, and there are entire dozens of such schemes! It is only worth understanding one important point. Such a connection is applicable only to the same type of wires. Otherwise, it is necessary to use special terminals or screw clamps.

You Need This Tool. Episode 69 | Stainless Safety Wire Pliers

As for the types of such a compound, that is, several basic varieties:

Over, each of these types can be parallel, consistent and branch. The so.Called subspecies. Simple twisting is widespread among home masters and, as a rule, is used in household conditions. In this way, wires in the distribution box are often connected. To get reliable contact of the wires, it is enough to choose the right tool and use the caps for twisting wires.

Bandage twisting is relevant for veins with a large diameter. Twisting with a groove is mainly used for a reliable connection of aluminum wires. If in the distribution box it is made with a high degree of accuracy, then the contact will be reliable.

In order to make each of these types of twists, you need to have certain skills. In this case, connecting wires with a section of cores of not more than 10 mm 2 is allowed to be connected by this method. In household distribution boxes, wires usually have veins with a cross section from 1.5 to 2.5 mm 2.

Twist

How to make wire twisting properly? The main thing is do not forget that it is categorically impossible to wrap one vein around the other! Both electrodes should be twisted at once. In addition, the skills of soldering will be further required here. Over, this method is suitable for connecting aluminum wires with copper.

First you need to remove the insulation from the wire, and the veins themselves should be cleaned to a metallic shine. After that, you can connect the veins by twisting them. Next, you should not melt the metal, but a solder, and you need to make sure that it flows inside the twist. Then the connected wires must be treated using a flux or rosin. After that, you can lower them into a soldering bath, holding them there a little (there will be enough for a few seconds).

It is better to cool them in a natural way, but it is not recommended to use water for this! In the end, it remains to hide the soldered twist under the island. For safety.

How to make wire twisting: 3 reliable ways

Twisting is the oldest, but not lost reliability method of connecting wires. Despite a large number of different clamps, twisting to this day is popular and is in sockets and distributions for decades. In this article we will tell you how to correctly twist the veins, so that the contact is reliable. We will show on the example of multi.Dilapers and one.Core wires. To perform all manipulations, we need

To ensure full electrical conductivity, an important point is the integrity of the wiring. Its damage or low.Quality clutch is unacceptable

It is important to guarantee a tight adjustment of contacts and the reliability of the connection in the zones of “electric nodes”. Distinguish certain methods that eliminate the breaks in the cable. Among them should be noted welding

It is applied to copper and aluminum wires. In this case, a particularly reliable adhesion is provided

Among them should be noted welding. It is applied to copper and aluminum wires. In this case, a particularly reliable adhesion is provided.

• Twist;
• Welding;
• Soldering;
• Scum;
• Terminal pads;
• Self.Incentive terminals (terminals of WAGO);
• PPE caps;
• Bolt clamp.

The most full.Fledged connection for wires made of copper is soldering. It is easy to carry out with flux (rosin, drill) and tin solder. Terminals are also used. A special device that is performed using screw clamps. They are selected separately in accordance with the cross.Section of the cores. Self.Eliminated terminals are often used to save time on electrical work. In order to isolate a twisted or soldered electrical connection, insulating caps of PPE are used. Today, the WAGO terminals are widely used in the energy sector, which are produced for wired wires and cables of various diameters. In addition, WAGO terminals allow you to connect veins from various materials (copper and aluminum).

The choice of which connection depends on various factors:

• Material (steel, copper, aluminum);
• The number of twisted elements;
• Section;
• Venue of work (house, street, in the ground, etc.D.).

How to twist the wires with each other?

Despite all the prohibitions in accordance with the current rules (GOST 10434-82 Contact electrical p.2.One.5), the usual twisting still remains the most popular way of connecting electric wires.

Our people twisted, twist and will twist.

Unfortunately, few people use subsequent soldering and even more so welding. As experienced electricians say: a cold connection is always hot and hot is always cold.

Nevertheless, the secret of the “eternal” twisting is simple to disgrace-twist the same wires (copper-honey, monobrazil-monothed), create a sufficient spot for contact, and reliably isolate everything from the air (the tube is with adhesive composition).

Here are the visual results of transition resistance measurements when connecting the wires with “legal” clamps of the VAGO or a cap of PPE, and “illegal” ordinary twisting.

Twisting demonstrates quite satisfactory results. In many cities there are houses of the 1950s, in which twisters still live.

In those days, if you do not twist it with high quality. They will quickly “twist” you yourself and “insulate” you for twenty years

In our being, most often it all ends with clumsy snotty and for reliability with a blue isolet on top of it.

Women were launched in mass consumption for completely other things Black isolet.

So how to twist the wires correctly? Even in Soviet textbooks for electricians, explanatory drawings were given.

But these are already pictures made in modern graphic editors.

Let’s take a closer look at the whole process of obtaining such a final result.

With the apparent simplicity of such a connection, even here inexperienced electricians manage to cure. For example, in this way.

But how is it right? Clean the veins for a length of 4-5 cm and bring them parallel to each other so that the ends are half entered for isolation.

There is an opinion that the longer the twist, the less it will heat up due to the larger cooling area. On the one hand, everything seems to be logical.

However, firstly, the temperature difference will be only a few degrees.

Secondly, this is all true for an unenvulated open-air connection.

In conditions of closed space (closed distribution) and a thick layer of insulation over the veins, the temperature difference will be invisible in general.

So, 4-5cm (matchbox size) for the most running wires 1.5-2.5mm2 will be more than enough. You will not receive special benefits from further increase in length.

By and large, it is needed only for more convenient work with wires.

So, bring the wires to each other and pinch their pliers in the middle.

Then you begin to tightly wind up one vein around the other. This method is called the sequential connection of the groove.

Here is clearly the whole process from A to me in the video from the Thaitrick channel.

For high.Quality twisting, divide each multi.Wirewear in half.

Next, tighten these halves clockwise to create a semblance. And then twist them together until the middle.

After that, attach the wires to each other in the joint and once again wrap them together. It should turn out such a “cross”.

Conclusion

Despite the rather strict rules for installing electrical installations or PUE, twisting will be well.Deserved for a long time, at least among home masters. Of course, in industry this method of connection for obvious reasons is not suitable, since it uses quite powerful equipment.

In addition, thick wires are used in this area that is simply impossible to twist. In other words, twisting will be useful in everyday life. It should not be forgotten that twisting aluminum wires is prohibited by PUE rules. However, in some cases, this method can be used.

TOP-10 useful nozzles for screwdriver with AliExpress. Burim, sharpen, grind, cut, and t.D

Twisting is the oldest, but not lost reliability method of connecting wires. Despite a large number of different clamps, twisting to this day is popular and is in sockets and distributions for decades. In this article we will tell you how to correctly twist the veins, so that the contact is reliable. We will show on the example of multi.Dilapers and one.Core wires. To perform all manipulations, we need

The most common mistake that most home masters make is to wind one wire on another. This option is committed unacceptable! Wire veins should be evenly wrapped in each other. Due to this, reliable mechanical strength is ensured, and the passage of electric current is not accompanied by any problems. Ultimately, such a mount will be able to last more than a dozen years.

An important factor is the length of the twist. Here, many make mistakes, making it very short. As a result, the connection simply breaks. The minimum allowable twisting length of electric wires is 30 mm.

In other cases, it all depends on the thickness of the wires. And the larger the diameter, the longer the twisting section should be. At the same time, any specific requirements regarding the conduct of twists do not exist for obvious reasons. For this reason, each specialist himself decides the relative method of connecting wires.

Toyota Sera Squirrel-Lyteyag Board Mountain [Lifehak] Method of correct twisting wires for lazy.

Today I would like to tell (or rather show) You about one very interesting twisting method copper multi.Core wires (car mainly), which I have been using it myself for a long time. It is the most correct from many points of view, but is the most unpopular due to the fact that it spends the largest amount of time.

Unfortunately, most of the electrics I know avoid this method, again, first of all, due to the fact that are lazy every time to do complex manipulations for each wire.

The final result (and A huge advantage) this type of twist is a wire connected from two pieces, a wire, the same cross.Section, without angles, tubercles and other non.Aesthetic. Absolutely direct wire, If you choose the color of the shrinkage at first glance and it cannot be said that it once consisted of two pieces.

The main disadvantage of this method is that with such a twist it is necessary Be sure to lose the wire at the junction (4 drawing in the photo above), since Without soldering the connection created by this method has Almost zero strength.

Actually, because of the need to have a soldering iron constantly at hand and, as a result, electricity for powering the soldering iron, as well as a minimum set of a novice soldier (flux, solder). Then this method It is not particularly popular among electricians and garage kulibins in Russia, then in the vast majority of cases, the familiar “method of parallel twist and island” is used to pain::

BUT, Today, brothers, I will show you the great invention sent to us by the Thor so that we, his sons, could make parallel twisting without all of the above having only a lighter with you in your

Here, even Vidyushechka took off for you, it is not very long. Only 2 minutes. Please give me a little time:

And it allowed me all this to do this thing. Solder pasta.

In my case it was Mechanic XG-Z40, She has a convenient tube-shreds, it is a pleasure to work with her.

It consists of mixed in a certain proportion of flux and solder powder. What follows another plus. It is no longer necessary (but still extremely desirable) to clean the wire from the “beaks”, when melting, this thing itself acquires excellent adhesion and spreading the wires of the wire (you can see).

Actually, what I am this post-there is a small “scream of the soul”: I am very tired of correcting customers in the car to correct this wonderful aspect left from previous owners and grief-electrics in the form of snot soples hanging with ribbons like vines (Remember, Most of the island of those sold in Russia for the “average consumer” turn into snot in a year, and we rarely use expensive elastic bands of type 3m), as well as parallel twisting twisting in all directions “atavism stumps” as a bouquet.

Enough! If you really need to twist a couple of wires, I alreadyI ask you to make a consistent twist (although the method considered in the article will take you much more time, it will bring much more reliability), I am convincingly asking. Think about those who buy your car after you, or at least about those who will then disassemble the whole thing (I’m silent about fire safety). Use at least a thermal shrinkage, it is not expensive, Sometimes it’s even cheaper than isolets if you buy a meter, but you will protect yourself and future owners from many troubles!

Thank you for listening, I hope that at least someone will enable this article =) and the Lord does not bring to face anyone to fire the wiring, this is a terrible thing!

Twisting schemes of wires

Twisting wires video

Also look at the device for twisting the wires with each other, it can be done without much effort. How, watch this video.

Twisting method with winding

Stir the wires at the ends and in the middle bend slightly, at the bend of the bend, hook the wires for each other. Then alternately wrap the ends of one wire around the other.

Adapter nozzle saber saw

An interesting device that turns a screwdriver into a small saw. The adapter is based on the convertible mechanism, which transforms the rotation of the screwdriver cartridge, into the next. Return movements of the saw. The delivery set has various saws for wood and metal, in the amount of nine pieces. In my opinion, this is a very useful device, especially for a private house: cutting tree branches, as well as cutting small boards will be much easier than manually sawing a hacksaw.

⚠ Twisting device! One day at the object! #Real_Electric

Twisting device! One day at the object! #Real_Electric report on the work done at the facility, answers to questions. I’m talking about the adaptation of which I make twists. Electric power in Kaluga. 8 910 918 08 18 Site. I am in contact. Group in contact. #real_electric

Device for quick twisting cable veins with AliExpress.

Good afternoon, ladies and gentlemen! Finally, a parcel with Ali Express came, today we will unpack it and test a unique device for a quick twisting cable.Is it unique since Chinese friends promise us? Learn in this video.Pleasant and useful viewing you. #Twist #Life hack #unBoxing

Shooting

A little later, a kind of apparatus for twisting wires will be considered. And before that we will analyze one well.Known but also contradictory way of connecting wires. It seems like it is very popular due to the fact that it will not work to break off contact or deform it. At the same time, there are some nuances associated with the choice of tool or sleeve.

The procedure itself is to press or local squeezing. Before the connection, both wires must be treated with special lubrication, which allows reducing friction and risk of damage. Then both veins are inserted into the sleeve from two side to their contact. Over, it is done so that the junction is at the center of the sleeve.

Having made a testing with a special tool, it is mandatory to isolate the place of the connection.