How To Properly Wind The Line On The Trimmer Spool

How do I wind the line around the Patriot trimmer reel? How do I wind the line around the Patriot trimmer reel? What are the rules for changing line? How to properly fill the line? What are the refueling errors? What to consider when threading the line into the trimmer spool?

How do I wind the line around the Patriot trimmer reel?

Almost every beginner when using a trimmer is faced with the problem of changing the line. While changing your line is easy, you need to learn how to do it right. Replacing the fishing line with proper skill will take no more than five minutes, it is enough just to constantly practice it. This article will walk you through changing your line using the Patriot trimmers as an example.

Instructions

In order to change the line, you need to remove the old one (if it was).

The reel is the part of the trimmer structure that is located inside the brush head, drum or bobbin. Heads vary depending on the manufacturer. But this article only covers Patriot, although their mechanism is used by many other companies.

Instructions on how to unscrew the manual head on the trimmer are described below.

1. First of all, you need to clean the head from dirt and adhering grass, if it is dirty. To do this, lift the brushcutter head up and, grasping the casing, remove the special protective cover on the drum.
2. The next step is to remove the spool from the drum. The reel can be easily removed even with one hand, because it is not fixed in any way inside the drum.
3. The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with the spool, while unscrewing the screw counterclockwise.
4. Now you can pull the coil out. As mentioned above, it is not secured by anything, except for a hook with a metal shaft, so it does not need to be pulled out with force. Carefully, in a circular motion, pull the spool out of the drum.
5. Now it remains to remove the old fishing line and follow the next instructions.

Replacing the coil and drum is performed according to the reverse algorithm.

Before threading the line, make sure you have purchased the correct thread for the trimmer. In the event that the thread does not fit, the fuel or energy consumption increases, as well as the load on the brushcutter engine.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m of line. The specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the spool itself. If you cannot accurately determine the length, you can do the following: insert and wind the thread until the coil is fully charged (the line level will be compared with the protrusions on the sides of the coil). Make sure that the line sits flat in the reel.

The instructions for threading the line into the spool are described below.

1. The prepared thread must be taken and folded in half. It should be ensured that one edge is 0.1-0.15 m longer than the other.
2. Now you need to take the ends in different hands. The one that is smaller must be pulled up to the larger one so that it becomes 2 times shorter. When bending, maintain an offset of 0.15m.
3. Find the notch inside the coil baffle. Carefully pass the loop you made earlier into this slot.
4. To continue working, it is necessary to determine the direction of winding the thread in the bobbin. To do this, it is enough to inspect the coil; there should be an arrow on it.
5. If the arrow-pointer could not be found, then it is quite possible that there is a written designation. An example is shown below. Inspect the coil head. It has a direction indicator. However, this is the direction of travel of the coil. To get the direction of winding, you need to wind in the opposite direction.
6. Now you need to load the spool with line. It is worth noting that there are special guide grooves inside the coil. Follow these grooves when winding the thread, otherwise the trimmer may be damaged. At this stage, you need to charge the coil very carefully.
7. When the user has wound up almost the entire thread, take the short end (do not forget about the 0.15m protrusion) and pull it into the hole located in the wall of the reel. Now you need to repeat this action in the same way with the other end (on the other side).
8. Place the reel itself in the head of the reel, before passing the line through the holes inside the drum.
9. Now is the time to put the drum back in place. After that, you need to take the ends of the line with both hands and pull them to the sides. Then you need to put the lid back on (here you can safely make efforts until a characteristic click is heard).
10. I just had to do some cosmetic work. We need to see if the thread is too long. You can start the trimmer and check in practice if everything is comfortable. If the thread comes out a little long, you can trim it with scissors.

Frequent mistakes

Although winding the line is very easy, many beginners may wind up the line incorrectly. Below are the most common mistakes.

1. Many people, when measuring a thread, think that 4 m is a lot. Because of this, people often measure less and, accordingly, they do not have enough line. Do not be afraid to measure out a lot, because you can always cut off the excess.
2. In a rush, some people do not follow the threading grooves inside the spool and wind the thread randomly. This will cause the line to fly out of the reel and may even cripple.
3. For winding, use only the appropriate line. This error is the most common. You need to monitor not only the thickness and volume of the line, but also its type. You should not use the first line that comes across for wrapping, which will not meet the goals. For example, you do not need to use a thread on young grass if you need to mow dead wood.
4. Do not turn on the device until it is fully wound and collected. While this is obvious, some people do it in order to check if everything is done correctly.
5. In no case should you confuse the direction of refueling, as this will overload the engine, and it will soon come out of working condition.

It is quite common for beginners to make mistakes, so you must follow the tips in this article.

Preparing to wind the line

Before the winding process, it is necessary to remove the spool with line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:

• Compact electric trimmers.

Straight bar trimmer

This model provides the ability to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To mount the trimmer knife, it is necessary to align the hole of the reel and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the body can be easily twisted clockwise by hand.

Trimmer head with two antennae

Double flute head

After removing the spool from the reel body, we determine the number of strands for winding the line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interlacing adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off the excess.

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these gardening devices, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer spool. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the line in the operating manual.

Single-barbed trimmer spool

Brushcutter reel with one antenna

Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is done in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the trimmer reel.

After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.

Winding the line to the trimmer

Measured and neat dismantling of the spool from the spit coil makes it possible to go directly to winding the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

1. Trimmer head with one working mustache;
2. Bobbin with two line antennae;
3. Automatic winding reel.

Trimmer head with automatic line threading

Types of trimmer heads

Some models on the market have a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic trimmer head include ease of threading the line, and the disadvantages of frequent breakdowns of the mechanism due to the complexity of the design and high cost.

How to properly wind the line around the trimmer spool?

Despite the fact that gardening equipment has been used for quite some time, it is still a novelty for some owners of private houses. This is why there are often questions about how to properly wind the line on an electric or gasoline trimmer.

This is essentially a simple operation, but all its stages must be performed correctly in order to achieve the desired result. Over, in the operating instructions, only a few manufacturers provide an answer to this sore question. Study the article to find out how the line winds around the trimmer reel.

The order of winding the line on the trimmer spool

First of all, you should know that trimmers have different working attachments. The reel can be designed for different lengths and thicknesses of the line, this point should be taken into account when purchasing consumables.

So how do you load the line into the trimmer reel? All work is divided into several stages:

1. First you need to disassemble the trimmer head.
2. Unscrew the attachment by rotating the drum to the right.
3. Press with your fingers on the two latches located on different sides of the entrance, and remove the top cover of the nozzle. You can pry off the cover with a screwdriver. This should be done carefully: reels with automatic line feed have a spring that can forcefully throw the cover along with all the contents of the reel.
   
4. Remove the old line scraps.
   
5. Now you need to find the middle of the line. To do this, unwind it to the required length (for example, 10 m), cut it off and fold it in half.
6. Hook the middle of the line into the existing recess or insert into the hole specially designed for this. And start winding. The direction is indicated by an arrow, which is usually marked on the trimmer reel body (usually against the drum rotation). Some models have a double-sided reel: in this case, the line should be wound in different directions: one end in one direction, the other in the other, while the loop of the line must be wound into the dividing slot in the middle.
7. Leave loose ends of the line about 20cm each. Later they will need to be fixed in the recesses.
   
8. And finally, the last step will be the assembly of the drum. Reinstall the washers and spring. On the top ring of the reel there are two notches where you need to tuck the antennae of the fishing line. Thread them through the holes and place the spool in the drum, taking care to tighten the line without dislodging the spring.
9. Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

When you turn on the trimmer, the excess line will be cut off by the trimmer blade.

As you can see, winding the line on the trimmer reel is not difficult: the main thing is to do everything right. And here are some more tips that will come in handy when choosing a fishing line, winding it and subsequent work:

• Fishing line comes in different thicknesses and with different sections. The best option for winding is the fishing line native to this model;
• Never use fishing line or metal cables for the trimmer. Such a substitution may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure not only the lawnmower himself, but also those around him;
• The line is cut when the trimmer is in contact with hard objects. Try not to allow this, otherwise you will have to stop every time, turn off the device and rewind the line on the reel;
• Use regular line for cutting lawn grass, and pigtail line for coarse weeds. It is more durable and will not constantly cut.

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Removing the coil from the trimmer

On small, bottom motor electric trimmers (when operating near the ground), the reel usually has two buttons on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When disassembling, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (on such trimmers it is not yet possible to put a knife), you need to grab the coil body with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, trying not to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers, in addition to the fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver crawls even deeper, and the coil will lock. Now we turn the whole coil clockwise (since the thread is left-handed) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted with a lamb. If the coil is on latches, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection between two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.

How to properly wind the line on the trimmer spool

Many, having worked out the factory line on a recently purchased trimmer, try to wind a new one, but cannot, because they do not know how to properly wind the line on the trimmer spool (bobbin). It seems that there is an instruction, but it still does not work. Let’s try to deal with this issue in this article.

So, in order to wind the line, you first need to remove the coil from the trimmer so it will be more convenient. The method of removal will depend on the type of trimmer.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find a fixing hole for the line on the inside of the reel, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. Having reeled up the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inside of the reel and designed so that at the time of collecting the reel the line does not unwind. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and thread the outer piece of fishing line into the existing hole, assemble and put the coil back on the trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is one groove, then both tendrils are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. A reel with one groove must have a through hole through which the line is threaded. We unwind 2-4 m of fishing line, thread it through this hole so that it sticks out equally on each side of the fishing line. And we simultaneously wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little fishing line unwound, fix the resulting ends in special grooves, and if they are not there we hold them with our fingers. We pass both ends into the existing holes on the outer casing of the coil. We collect the coil and attach it to the trimmer.

If there are two grooves, fold a piece of fishing line 2-4 m long in half, insert the loop obtained at the place of the bend into the groove between the two grooves, and simultaneously wind both ends of the fishing line, each along its own groove. Further actions are similar to the previous option.

There are also reels in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, without winding, are threaded completely through the holes on the outer body of the reel, collect the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Rotate the button inside the fishing line itself. In this case, it will not work to turn it in the wrong direction, since it can only turn in one direction. If you get used to it, you can wind fishing line on such a reel, without even disassembling it, you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

How to wind the line correctly: replacement features depending on the type of removable trimmer coil

To figure out how to thread the line into the detachable trimmer head, the following guidelines and instructions will help.

How to quickly and easily remove the coil with your own hands

Remove the head before replacing the old line with a new one in the detachable trimmer reel.

The process is completely simple, even beginners can do the job:

1. Remove the upper retaining cover.
2. Take out the removable spool.
3. Take out the spring, if any.
4. Unscrew the bolt with a screwdriver.
5. Remove the housing from the shaft.

By quality

Before putting on the line on the trimmer, you need to pay attention to the section of the cord:

• Round thread is the most common option. They cut the grass perfectly, even in difficult areas;
• Spiral line is suitable for thin grass. It is not very durable and is not suitable for old thickets;
• A cord with notches and sharp edges is chosen for mowing weeds;
• Fishing line with a variety of geometric sections will help to mow the lawn more evenly, but the consumable strength is low.

The owner of the brushcutter should be aware that it is strictly forbidden to use metal wire, fishing thread and various strings.

How to properly wind the line around the trimmer: step-by-step guide and instructions

A beautiful lawn will only look truly well-groomed if you regularly mow the grass. A trimmer is best for tackling difficult areas. Any owner of the machine will sooner or later face a solution to the problem of how to wind the line on a reel, because wrong actions can not only worsen the quality of the mowing, but also disable the equipment. Today in the Homius review we will tell you about all the methods and nuances of replacing the fishing line and the features of choosing consumables.

What are the trimmers and features of their use

The trimmer is useful for trimming small or difficult areas, such as near hedges, between beds and along paths. Today, manufacturers produce a wide variety of gasoline, electric and battery models, which can be selected for any owner’s request.

A fishing line is used as a cutting element of the trimmer. In the process of work, sooner or later, its length will end, and then the owner will have a question of how to correctly replace and fix the thread tucked into a removable coil.

How to wind the line correctly on the spool of a single-barbed trimmer

Most often, a thread up to five meters long is used. The procedure consists of the following steps:

1. Bend the cord with a loop and insert into the groove of the head.
2. Wind the thread in the opposite direction to the marks on the body. They indicate the direction of movement of the head.
3. Leave the end of the thread up to fifteen centimeters long to increase the centrifugal force.
4. Thread the free end through the spool outlet.
5. Assemble the trimmer head.