How to Dilute Gasoline For gas trimmer Properly

A deposit on the electrode electrodes is formed due to improper adjustment of the trimmer carburetor, if there is a lot of oil in gasoline and when the air filter on the trimmer is dirty. how to dilute gasoline (AI 92) for a benzo braid, trimmer.

How to Dilute Gasoline For Benzotrimmer Properly

Preparation of a fuel mixture for two-stroke engines

Secondly: it is necessary to remove the carburetor, disassemble it completely (especially the part where the membrane and underneath the valve), clean the carburetor channels with a thin copper wire (so as not to scratch), then rinse the carburetor thoroughly with clean gasoline (without oil) and blow it with a pump with a purge tip (assemble the carburetor, start the scythe and adjust the carburetor). Remotely hard to diagnose a trimmer malfunction. I think gasoline or air is pumped into the tank through the return hose somehow with a membrane. The video shows how to make a fuel mixture for two-stroke engines. Refueling mtkosa, chainsaws and.

Fuel mixture to benzokosa and chainsaws. Correct proportions

If the candle has not turned, then everything is fine, but with subsequent eversion of the candle, one must be especially careful. If the candle is cranked, you will have to install the futurka (repair sleeve). To do this, it is better to contact the workshop for repairing chainsaws and gas trimmers. There are a lot of descriptions on the Internet how to properly prepare the fuel mixture for chainsaws and chainsaws. But not always.

How to dilute gasoline with oil for a chainsaw or Lawn Mower

Replace the bearings in the trimmer gearbox yourself (keys are needed to remove the gearbox; pliers to remove the retaining rings and disassemble the gearbox; gasoline to wash all the insides for component troubleshooting; new bearings of the trimmer gearbox for replacement) or replace the gearbox bearings in the workshop. If only one bearing of the trimmer reducer collapses, it is necessary to change both bearings anyway. Or, as an option, replace the trimmer gearbox assembly. select the gearbox for the diameter of the pipe onto which it will be clamped along the splines of the drive shaft (square, star, hexagon). Do-it-yourself brushcutter repair is similar to trimmer repair. General recommendations for the preparation of the fuel mixture for 2-stroke engines of chainsaws, scythes and more.

HOW TO CORRECTLY PRODUCE GASOLINE WITH OIL 1:50

Video: How to Dilute Gasoline For gas trimmer Properly


Poured gasoline with oil, oil was a little more than expected. And in the morning I wanted to start it, but as if holding a piston, it spins in jerks. And as I put a candle, the piston in the cylinder starts to slow down, walks tight and jerky. Dismantled the cylinder and removed the piston, from excess oil on the piston head and the cylinder was soot. In this video I will tell you about the correct preparation of the fuel mixture for two stroke engines!

How to prepare the fuel mixture?

I wash the air filter after the engine rolls out every 20 liters of gasoline and before doing trimmer repair or trimmer maintenance. We are preparing a fuel mixture for two-stroke engines together with a TMK technical specialist. Before.

How to breed oil on a trimmer and a chainsaw.

Thermal breakdown of the piston pin retaining ring due to insufficient lubrication (low oil in gasoline, and oil removes heat from heated parts). information on our website How to dilute gasoline with oil for trimmer and chainsaw? All is well.

Two-Stroke Fuel Mixture / Refueling Motocosa Trimmer Chainsaws Chainsaws

I do not know the cause of the malfunction of the trimmer when the gas in the trimmer tank is seething. But I can express my opinion about this, and you will check in practice. How to prepare a fuel mixture for two-stroke engines. Refueling chainsaws, trimmers, and chainsaws.

The right fuel mixture for a gas trimmer or chainsaw

For Husqvarna oil, the norm for mixing oil with gasoline for the trimmer is 1:50, t. For other oil and engine manufacturers, the norm for mixing oil with gasoline is 1:33, t.

The most accurate dosage of oil for 2 stroke engines motokos motor sprayers chainsaws, etc.

The main thing when installing the spark plug. first you need to wrap the candle several turns FROM HAND, and then take the key. If the candle went by hand easily, it means it is installed correctly and it can be wrapped with a tool (candle key with a screw). If the candle does not want to be twisted by hand, it is not worth tightening it with a key, since the candle did not go through the thread and the thread in the candle hole of the cylinder will inevitably be damaged and an expensive trimmer motor repair will be needed. Fuel mixture.

Making a bottle for mixing gasoline and oil for two-stroke engines

Tell me, when starting the trimmer, the gas in the tank starts to seethe and flow out of the tank, with an increase in the revolutions, the accordingly increases and gasoline flows from the tank from under the rubber band through which the tubes enter the tank. You can take a measuring cup, pour it into a bottle of water to the right place, put a mark, pour water into the measured one.

Which gasoline to fill 92 or 95

Remove the decorative cover that covers the shock absorber (unscrew the 2 screws on the sides). Then loosen the bolt tightening the rubber shock absorber around the bar. Install the rod correctly relative to the engine, set it deeper, until it stops. We will talk about gasoline. Which is better to fill in. AI 92 or AI 95.

How to Properly Dilute Gasoline For a Trimmer

Depending on the variety of trimmers, they can be filled with a fuel mixture or separately with gasoline and oil. Now there is a huge variety of types of motor oils that are suitable for various equipment, including garden. In order to choose the right fuel for a particular model of Lawn Mower, you need to know its technical features and understand the brands of gasoline, as well as liquid lubricants. All details on how to dilute gasoline with trimmer oil are in the material below.

Features of refueling motokos

Depending on the engine design, the scythes are divided into two-stroke and four-stroke. In the first case, the piston in the internal combustion engine makes 2 strokes in one working cycle, and in the second case. 4 strokes. Differences in the operating principle of the engine determine the different approaches to refueling the trimmer.

Refueling with two-stroke engine

In ordinary household models, a motokos uses, as a rule, a two-stroke engine. For the brushcutter does not need a very large power and agility, so it is quite suitable for the fulfillment of tasks. In addition, this engine is much cheaper and simpler, but it is fueled with a fuel mixture that consists of oil and gasoline. Such fuel is poured into the carburetor and fed into the cylinder in the form of oil-gasoline fog. Thus, the oil provides lubrication of all necessary parts, and during the operation of the engine burns out along with gasoline. However, the combustion of this mixture is accompanied by the release of a pungent odor and smoke, which increases the toxicity of exhaust gases.

How to Properly Dilute Gasoline For a Trimmer

Important! For such motokos it is necessary to use a special oil for two-stroke engines, which completely burns out without leaving a burn, and has low volatility. And so that it mixes well with gasoline, it contains 20% of the solvent.

Four-stroke engine refueling

Four-stroke engines are used in professional motokos models. They have great power and can work for a long time without a break and refueling. They are also used as fuel. gasoline and oil, but they are poured into different tanks. This means that the oil does not participate in the combustion process, so the exhaust gases are not so toxic.

On a note! Along with the best environmental performance and the ability to heat less, four-stroke engines of motokos are also more economical. They consume much less fuel. savings reach up to 50% in gasoline and up to 80% in oil.

Video: How to Properly Dilute Gasoline For a Trimmer


Rules for choosing gasoline

Before buying fuel for your Lawn Mower, you need to read the manufacturer’s instructions. It indicates the grades and brands of fuel that can be used for a specific trimmer model. In general, when choosing gasoline, you need to focus on the A-92 brand. A-95 is also suitable for refueling Lawn Mower, although some experts do not recommend taking fuel with such an octane rating. This is due to the fact that at many gas stations, the composition of such gasoline includes various additives and solvents (for example, alcohol). It should be borne in mind that you can’t save money in this matter. in order to extend the life of the brushcutter, you should choose only high-quality fuel from trusted suppliers.

Oil Selection Rules

Motor oil, depending on the chemical composition, can be:

  • mineral. is made from petroleum distillates and is intended for low-power equipment with air cooling;
  • semi-synthetic. is a mixture of mineral and synthetic oils and is suitable for 2T and 4T, as well as for air and liquid cooling;
  • synthetic. made on the basis of esters and can be used in powerful technology, as well as for working in difficult climatic conditions.

Important! Oils for two-stroke and four-stroke engines differ in their ability to dissolve, burn and evaporate. At the same time, so that the liquid lubricant differs from gasoline, it is painted in different colors: blue, green, red.

Depending on the API classification, the following groups of oils for trim motors can be distinguished:

  • TA. for low-power equipment with an engine capacity of up to 50 cm³ and air cooling;
  • TV. for powerful equipment with an engine capacity of 50-200 cm³ and an air cooling system;
  • TS. for powerful two-stroke equipment (motor-scythes, chainsaws, lawn mowers, etc.) with an engine volume of 50-200 cm³;
  • TD. for boat engines with liquid cooling.

To choose the optimal oil for a particular trimmer model, it is better to take into account the recommendations indicated in the instructions. For motokos 2T API-TV and API-TC class oil is usually used.

On a note! In addition, for two-stroke engines there is a JASO classification, and for four-stroke engines, SAE30 is still used.

Leading manufacturers of garden equipment themselves develop and produce oils for their equipment. Such lubricant compositions most fully satisfy all the technical and operational characteristics of a specific series of trimmers. For example, for Stihl Lawn Mower FS 5 it is best to use Stihl HP or Stihl HP SUPER oil, for Husqvarna 143R, Husqvarna HP or Husqvarna LS oil is suitable. But for the Patriot brand, the usual mineral oil M-8B is also suitable.

Rules for the preparation of the fuel mixture

For many beginners who have bought a Lawn Mower, the issue of diluting gasoline with oil to prepare a gas mixture becomes a problem. After all, you need to know the proportions and very carefully adhere to them. The instructions for the product usually indicate in what proportion to dilute the components: 1:25 or 1:32, or 1:40, or 1:50. This means that for 1 part of the oil, you need to take 25, 32, 40 or 50 parts of gasoline and mix them.

Of course, it is inconvenient to measure in such categories, therefore it is better to determine how much oil is needed per liter of gasoline using simple mathematical calculations. To do this, divide 1 liter, which is 1000 ml, into a known proportion. The following mixing table is obtained.

How to Properly Fill a Fishing Line With a Trimmer Video

How to correctly tackle a fishing line in a trimmer

How to Properly Fill a Fishing Line With a Trimmer Video

How to correctly tackle a fishing line in a trimmer

How to wind a fishing line on a trimmer. Oleo-Mac trimmer head

How to properly thread fishing line into a gas trimmer coil or

Winding fishing line on trimmer

Trimmer fishing line, how to wind a fishing line on a trimmer reel

How to Replace a Fishing Line in a Trimmer Coil

How to reel a fishing line

Trimmer. Husqvarna 323R brushcutter

NEW Automatic brushcutter reel

How to replace a fishing line on a Shtil trimmer. improved

Fishing line for trimmer. how to refuel

trimmer. how to wind a fishing line

AutoCut Bobbin Fishing Line for Stihl fs 55 Trimmer

Stihl fs 55 petrol trimmer Review, Operation experience

How to wind a fishing line, cord, for a trimmer

replacement of fishing line in the trimeric head

Refueling fishing line into the reel trimmer 2 part

Video: How to Properly Fill a Fishing Line With a Trimmer Video


TRIMMER CARVER GBC-31 F

Sewing the line into the mowing head

Husqvarna trimmer. replacing cord of fishing line, string, cord

How to replace a fishing line in any trimmer

How to wind a tie, fasten a fishing line or braid cord on

How to thread fishing line into the trimmer coil

Coils exist different. For a coil working with one antennae, it is easier to refill a fishing line than with others. In the inner part of the reel there is a hole designed to fix the fishing line. You need to insert the tip of the fishing line into it and start winding it.

Important. you need to wind in the opposite direction from the rotation of the coil on the trimmer. Look carefully, most likely in the same place, on the reel, the direction will be indicated with a stick where to wind. It can take about two to four meters of fishing line to wind. it depends on the size of the reel itself. At the end of winding, a small piece should be left free. He will come out. In order to clamp it, there is a groove, which is also located on the inner surface of the coil. This groove firmly fixes the end of the fishing line and prevents it from unwinding when assembling the reel. If the design of the reel does not provide for this groove, then hold the end of the fishing line with your hands yourself. Now you can attach the outer part of the coil. It also has a hole in which you need to thread the outer piece of your fishing line. Now you can return the assembled coil to its place on the trimmer.

Now about the coils, designed to work with two antennae. First you need to see how many reels there are for fishing line on the reel. The presence of either one or two in different designs of coils. And then it already becomes clear how it will be necessary to reel. two antennae at once in one groove, or # 8212; each antennae is separate. Please note that if there is one groove in your reel, the fishing line hole must be through. Now you need to rewind the fishing line about 2-4 meters and pass it through this hole so that the fishing line is the same on one side and the other. Now look again, there will be an arrow indicating where to wind. The direction is against the direction of rotation of the coil on the trimmer. Winding two tendrils of fishing line at once, together. Leave the small ends. If there are special grooves. we clamp in them, if not. then just hold tightly with your hand, with your finger. There will be two holes in the outer case of the reel. a separate line for each end of the line. They did it, assembled the coil and put it on the trimmer.

If you have a reel with two grooves, then the rewound piece of fishing line (all the same 2-4 meters) needs to be folded in two, and in the special groove (it should be located just between the grooves), insert the bend of the fishing line, that is, the middle, folding her in the shape of a loop. Winding, as in the previous case, you need both fishing lines at once, only this time. each in a separate groove. And then. as described above. fixed, attached the upper case, secured the coil to the trimmer.

Another variety of coils is with a through hole on its inside. There are holes on the outer casing. That is, it turns out that the fishing line needs to be passed through these holes in both the inside and the outside, and immediately assemble the coil. And for winding use a button (this is the same button that is used to release the fishing line during operation). Just to rewind the fishing line now you need to rotate this button. over, the mechanism of this button is designed in such a way that you can twist it in only one direction, just the direction you need.

Gasoline trimmer refueling instructions

Fishing line selection

In order for the trimmer to work “like a clock”, you need to choose the fishing line correctly, that is, pick it up taking into account the model of the trimmer and the type of work. Two important parameters in this matter. this is the diameter and cross section.

The diameter of the fishing line should correspond to that recommended for this model (it is obligatory indicated in the passport for the product).
The cross-section of the fishing line is round, square, with sharp edges (pentahedron). A line with a round cross-section is intended for mowing young grass and lawn, a square and five-sided line is useful if the grass is coarser, and weeds have grown on the lawns.

Trimmer Head Modification

The mowing heads of the trimmer can be of various modifications: single-string for trimming the lawn (mowing with a single thread of fishing line); two-stringed for mowing grass and clearing territories with automatic feeding of fishing line or manual adjustment of the string length.

Modern manufacturers are increasingly offering gardeners universal trimmers with two-string automatic mowing heads.

Step-by-step instructions for refueling the fishing line into the trimmer

  1. Push the clamps inward until they click and remove the cover from the mowing head.
  2. Gently turn the coil, it will be released from the holder, and now remove it.
  3. Cut two identical pieces of fishing line (the cut of the edge of the fishing line should be at an angle. This will facilitate the work). Take one of them and insert the end of the fishing line into a special pocket on the reel (there may be hooks, ears, clips). Next, wind the string in the direction of the arrows. Distribute the line evenly, tightly. Fasten the end of the string into a specially provided hole in the coil.
  4. Perform the same operation with the second part of the fishing line, only refuel the end on the reel from the opposite side.
  5. Return the reel with fishing line to the mowing head. Through the holes in the reel, pull out the ends of the fishing line and thread them into the special head connector.
  6. Gently straighten the fishing line and close the lid. Cut off the excess fishing line, leaving 12-15 cm of each edge.

Everything is ready. The trimmer is tacked with fishing line and ready to go. Now you can happily take up the obliquity of your favorite meadow, summer cottage, house territory.

It is only important to remember that not only the quality of the work performed, but also your safety will depend on how you fill the cutting line into the trimmer.

Video tutorial on refueling a gas trimmer fishing line (scythes)

Trimmer Operation Principle And How To Use It Properly: Refueling And First Start

Lawn Mower are devices with which it is easy to care for lawns. The question of how to use the trimmer is asked by those buyers who are just about to purchase a garden tool. The industry produces devices of different types, so when choosing, you need to pay attention to their characteristics.

Trimmer Operation Principle And How To Use It Properly: Refueling And First Start

Principle of operation

If we consider the principle of operation of the trimmer, then it looks like a hand braid. The difference is that it is equipped with an engine, with its help the cutting element is driven into rotation.

Manufacturing companies produce the following models of mowers:

  1. On which a gas engine is installed. Such garden tools have a fuel tank, this is their distinguishing feature.
  2. Devices with an electric motor. These tools have less weight, because they do not have a fuel tank. But when choosing such models, you need to consider that for their work you need a power source.

All electric braids can be divided into those that operate on batteries, and models connected to the electrical network. Each view has its own characteristics, but they affect the power supply. If you do not take it into account, then the remaining parts of the design are similar for different devices.

If you take any trimmer model, then it consists of elements such as:

  • motor;
  • fuel tank (electric motor-scythes do not have one);
  • levers with which the mower is controlled;
  • knife for cutting grass;
  • barbell;
  • a spool with wound fishing line used to cut grass;
  • protective cover;
  • bevel gear.

The engine is placed near the mowing head; it can be installed from below or from above. Only those models that have a direct boom have a gearbox. If it is curved, the main bearing becomes the connecting element. It consists of 2 bushings.

As a cutting device, a fishing line is used. It is easy to replace it with steel knives and wheels, they can be made of plastic or metal.

The choice of the cutting element depends on how hard the grass will have to be mowed. Most often, fishing line is used in the work, it is called cord. On sale there are products of various shapes, among buyers in demand spiral and round.

The fishing line is wound on a reel, it is inserted into the bobbin, while the 2 ends of the wire remain free. When the mower engine starts to work, the bobbin rotates, the grass is cut off by the free ends of the fishing line.

How to use a trimmer

Garden trimmers are effective. Beginners think that working with a lawn mower is easy, because you just need to plug it into a power outlet or pour fuel, but this is not entirely true.

The efficiency of the garden tool and its service life directly depend on the operating conditions. Therefore, before using the trimmer, you need to perform preparatory work.

The lawn with which to mow the grass is carefully examined. Be sure to remove glass and large stones. Having flown out from under a working mower, they can injure a person. The wire is removed from the lawn, because it can be wound around a rotating element, breaking the mower.

After that, they proceed to the installation of the cutting system. There are small power trimmers on sale that use only fishing line. It is designed for mowing juicy and soft grass. But there are models with a capacity of more than 1 kilowatt, on which metal knives are installed. They cut sow thistles and other hard weeds, trim the young shrub.

In order to replace the cord with knives, you need to unscrew the fastening nut, install the cutting element. Then the nut must be returned to its place, tightened with a wrench.

The operator must take care of his safety. Mow the grass in tight protective clothing. Special glasses are used to protect the eyes, they will protect from dust, grass and flying debris. Hands cover with gloves.

Video: Trimmer Operation Principle And How To Use It Properly: Refueling And First Start


An electric trimmer is included in the network, and battery models charge several hours before use. Fuel is poured into a gas mower.

The mower is held so that the spool or knife is parallel to the ground. When the tool is installed in the correct position, turn on the motor. After the grass is mowed, the mower is turned off.

First start

Before the first start, the operator collects the mower, the procedure is described in the instructions that are attached to the product.

If the trimmer is gasoline, it must be checked before use. The fuel tank is filled up to the neck.

The engine must run on fuel, so when you first start it should run for several minutes without load. After that, start mowing the grass.

How to refuel a gas trimmer

Gasoline powered scythes come with two-stroke and four-stroke engines. The first option is much more common. What differences can be distinguished between them:

  • trimmers with a 2-stroke engine have a faster response to pressing the power lever (for this reason, the brushcutters are mainly equipped with this type of engine);
  • a tool with a two-stroke engine will be much easier and also easier to maintain;
  • fuel consumption of a two-stroke engine is higher than that of a four-stroke engine with a similar power by about 30%;
  • A 4-stroke engine is more environmentally friendly, since the fuel in it burns out completely and is not emitted into the atmosphere, and its noise level is much lower;
  • and the most important distinguishing feature is the refueling: a 2-stroke engine is equipped with one common tank, where gasoline mixed with oil is poured; The 4-stroke engine has a separate gas tank and engine oil tank.

For refueling, it is necessary to use fresh AI-92 or AI-95 gasoline and high-quality motor oil for garden equipment (manufacturers produce different types of oil for 2- and 4-stroke engines). Oil can be used mineral, semi-synthetic or synthetic.

The proportion of gasoline and oil for trimmers with a 2-stroke engine can be found in the operating instructions for the specific model. Usually it is 50: 1, in some cases, a ratio of 25: 1 or 40: 1 is recommended. It is necessary to prepare the fuel mixture in a separate container with exact proportions. Never pour liquids “by eye” directly into the tank without first mixing them. Detailed instructions for mixing gas oil, with video and description, can be found on our website here.

Running in

Before starting operation, gas mowers must be run in. The operator turns on the motor; he has to idle for some time. It is necessary to ensure that the engine does not overheat, there should be no load.

When running Lawn Mower load increase gradually. If you start work at high speeds, the engine will run in poorly, this will affect the further operation of the mower.

When you first start it is not necessary to fully develop a temporary resource. After the engine runs at idle, you can proceed to the processing of the lawn. Lawn Mower should work no more than 15 minutes, after which the motor is turned off, it should cool down.

If you want to run the electric trimmer, the braid is first collected. Then make trial runs at least 3-5 times. If the engine works well, go to the mowing. At first, they work no more than 5 minutes, then the duration of work is gradually increased.

How to wear a belt

If the tool has a shoulder mount, before starting work it hangs on the shoulder. The trimmer is fixed on both shoulders if it has a backpack mount.

The model with the bicycle handle is held with 2 hands, the D-shaped handle is wrapped around the palm of your hand. The belt must be worn so that it is comfortable, then the back will not get tired.

How to mow the lawn to make it smooth

To keep the grass trimmed evenly, lower the mower as low as possible during operation. The plot must be divided into squares. You need to work, moving clockwise. In this case, the hay will always lie on the left, without interfering under your feet.

Kosim under the hay

Hay is better to mow not with fishing line, but with a metal disk. The grass is cut under the root, preserving its length as much as possible.

Mowing tall grass

If you need to mow tall grass, this is done in several passes. He processes the lawn 2-3 times. The rotating part is lowered from top to bottom, in this case the grass is not wound on a reel.

The operator must remember that grass wound around a reel causes the motor to overheat. If this happens, the Lawn Mower is turned off and the coil is cleaned.

It is most effective to mow the grass with the tips of the line, rather than the entire length. In the second case, the tool works worse, engine overload is possible. If you need to cut the grass over a large area, to increase the efficiency, the trimmer should be tilted towards mowing.

Wet weather operation

Electric mowers must not be used in rain, possibly short circuits. When the rain stops, you need to wait until the grass dries.

Not all gas mowers are protected against moisture, so some manufacturers prohibit the operation of mowers in the rain.

Mowing time

You can use the electric grass trimmer for no more than 20 minutes, after which you need to take a break for the same time. Violation of the operating mode negatively affects the engine, reducing its resource.

Gas mowers work from 40 minutes to 1 hour, and professional tools can mow grass until the fuel runs out. The break between work should be at least 20 minutes.

How often do you use such an indispensable helper as a trimmer in the country or garden?

How to Properly Install a Knife on a Trimmer Video

How to install a fishing line on a video trimmer

How to wind a line onto a trim reel

  • First, the head needs to be disassembled, for this we press our fingers on the two latches that are placed on the body of the head at 90 degrees from the notch, and remove the top cover.
  • After you remove the top cover, you need to get the cord holder, with all this, be careful not to lose the spring, as well as the holes for which the fishing line is fed. How it works How to reel a line on a reel Recently bought a trimmer and start. Measure out the required amount of fishing line and fold it in half.
  • Throw the folded fishing line in the middle onto the holder (it has a special slot) and start winding the cord so that each of the two mustaches lies in its holder compartment.
  • Leave the free length of the mustache about 15 cm, fix them in the special slots of the holder and install it in the lower part of the head.
  • Remove the mustache through the eyes and install the top cover of the head, aligning the side latches.
  • As a result, you got the head correctly locked by the fishing line, you can continue to work.

And in the end, a video on how to quickly fill a fishing line into a trimmer head.

How to wind the line on trimmer coil

Many, having developed a factory fishing line on a trimmer not so long ago obtained, try to rewind the newest, but they cannot, because they do not know how to wind the line onto the reel coil (bobbin) correctly. If in doubt or it’s not entirely clear how to charge the line onto the trimmer, how to wind the line. As if the annotation is, but still does not work. Let’s try to deal with this issue in this article.

So that win line, you must first remove the coil from the trimmer. The removal method will depend on the type of trimmer.

On small electronic trimmers with the bottom position of the motor (when it is at work near the ground), the coil usually has two buttons at the edges. Click on them and disconnect one half of the coil body from the 2nd, which remains on the trimmer. Together with the first half, the inner part is taken out, on which the fishing line is wound specifically. When parsing, be careful: inside there is a spring that can fly out and get lost.

On electronic and petrol trimmers with a bent bar (on such trimmers there is still no ability to put a knife), you need to grab the coil body with one hand, and with the second hand you need to start turning the lamb on it. Specifically, he strengthens the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, being careful not to lose the spring inside.

On electronic and petrol trimmers with a straight rod and a reducer at its end (you can also install a knife on the trimmers besides fishing line), we look for a hole under the coil, insert a screwdriver, for example, in it, quietly rotate the coil until the screwdriver penetrates even deeper and the coil will lock. Now twist the entire coil clockwise (because the thread is left) and remove it from the trimmer. Next, we disassemble the coil. How to wrap fishing line on a reel? Then you should reel one half of the fishing line into. It can be assembled using latches or twisted by a lamb. If the coil is on latches, then we press along the edges on the base of the latches, so that they bend and release one half of the coil body from the other. We just twist the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand and the upper one with the other, and start turning them in the opposite directions. When disassembling such a coil, it is also necessary to watch so that the inside spring is not lost.

Now, having removed and disassembled the reel, we proceed, in fact, to the main question. How to wind the fishing line correctly.

Read the same

If your coil is designed to work with only one antennae, then everything is very simple. It is necessary to rewind 2-4 m of fishing line (depending on the size of the reel), find a hole fixing the line on the inside of the reel, insert one end of the line there and start reeling in the line in the direction that the reel rotates on the trimmer. On the inside of the reel, they usually indicate an arrow, in which direction to wind the line. The trimmer is like a fishing line. If set instead. After winding up the fishing line, we leave its small piece uncoiled to expose it. We fix this piece in a special groove located on the inside of the reel and created so that the fishing line does not unwind at the time of collection of the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the upcoming collection of the reel. Next, take the outer part of the reel and thread the outer piece of fishing line into the existing hole, collect and put the reel back on the trimmer.

How to wind a fishing line on a mowing head of a trimmer or Lawn Mower

AT video carefully shown how to reel fishing line to the reel trimmer or Lawn Mower. Gas station fishing line mowing

Manual mower. Replacing fishing line in the reel.

In this video, I show how simple and easy to reel fishing line to reel a manual mower without the help of others

If the coil is designed to work with 2 antennae, then do the following. On the inside of the reel, we see how many grooves are available for winding fishing line. There can be one or two. If there is one groove, then both antennae are wound along this same groove. ? How to install a mowing head and a knife on a trimmer replacing a gas joint ring. If there are two grooves, then each antennae is wound on its own groove. The reel with one groove should have a through hole into which the line is threaded. Unwind 2-4 m of fishing line, thread it through this hole so that on each side of the fishing line sticks out identically. The usual inexpensive trimmer, it seems like without a trimmer for three correctly wrap. And we immediately wrap both antennae of the fishing line in one direction, the reverse direction of rotation of the coil on the trimmer and coinciding with the direction that the arrow shows on the inside of the coil. We leave the fishing line a little unwound, we fix the ends in special grooves, and if they are not there, hold with our fingers. We thread both ends into the holes on the outer case of the coil. We assemble the coil and attach it to the trimmer.

If there are 2 grooves, we fold the piece of fishing line 2-4 m long in half, insert the loop obtained at the bend point into the groove between the 2 grooves, and immediately wind both ends of the fishing line each in its own groove. Subsequent acts are similar to the previous version.

There are still reels in which the line is threaded through the through hole on the inside, the ends of the line, without winding, are threaded one hundred percent through the holes on the outer case of the reel, the reel is assembled and the button, which is usually pressed, is started to turn so that the line release as it wears out. Turn the button. Inside the line itself is wound. With all this, twisting it in the wrong direction does not work, because it can spin exclusively in one direction.

That’s all for the matter. Now you understand how to wind the line onto the trimmer reel correctly.

Read also:

How to refill a fishing line in a trimmer so that working with it does not tire

Many summer residents use a trimmer. a scythe with an electric or gasoline engine to combat weed. How to wind a fishing line on a trimmer reel. photos and video how. It is convenient when working in places inaccessible to the lawn mower: at fences, flower beds, houses, in the garden on narrow aisles, and can cut small branches. How to charge a fishing line to a trimmer, we recommend watching a video: how to wind a fishing line. The main element of this wonderful technique is an ordinary fishing line wound on a reel. The device is simple, but the cutting part wears out quickly, requires replacement. And the question of how to fill the line in the trimmer worries many owners of cottages.

Briefly about the fishing line

Read the same

Taking into account the models of the tool, the thickness of the fishing line is 1.2-4 mm. On the market for gardening equipment, there is little how to fill the line with the Nike-1750 trimmer. There are such configurations:

  • round. the most durable;
  • curly. for soft grass;
  • twisted or notched. for thin grass;
  • professional, not suitable for all instrument models.

When replacing the cutting thread, you need to choose the one that suits your type of trimmer. Preference should be given to specialized. Before filling the fishing line into the trimmer coil, it is better to soak it for half an hour in water. 03/28/2018 shaliris comments on how to install a coil on a trimmer how to make a coil. Then it will become more elastic and stronger.

How to quickly remove a coil from a tool

Before the thread is wound on a bobbin, it must be removed. over, the removal methods depend on the features of the tool. On trimmers with a motor near the ground, the spool has two side buttons, when pressed, a part of the housing is separated along with a thread winder.

On instruments with a bent rod, the lamb on the fixture is moved counterclockwise; having disconnected it, they remove both the bobbin and the spring inside it. On trimmers with a straight bar, fix it with a screwdriver, rotate clockwise and remove. Then the device is disassembled either using latches, or by moving its parts in different directions. The spring is taken out of the coil.

Refueling the fishing line with a trimmer

The main question is how to wrap the fishing line on the trimmer coil, fixing it securely there?

In the case of a device with one antennae, unwind up to four meters of fishing line, insert into the hole inside it, fixing the fishing line, one end of it and move in the direction indicated by the arrow. The edge of the thread is fixed in the groove inside the bobbin so that when it is assembled, it does not unwind. Lawn Mower huter ggt 2500t video bought a huter gas trimmer how to reel a fishing line on. If there is no groove, then this free end is fixed with a finger. Then the coil is assembled.

How to refill the trimmer coil if it has two antennae? In this case, check how many grooves are on it. one or two. In the first case, both antennae are sent to the common groove, if there are two of them, then each of them. in its own. 2-4 meters of thread are passed through the hole so that the free edges of the thread are the same length, and twist the bobbin in the direction of the arrow. The ends of the thread are inserted into the grooves or held with a finger, assemble the device and attach to the trimmer.

In a spool with two grooves, the same piece of thread is folded in the form of a loop, sent to the groove between them and the ends are wound simultaneously. How to install a 2-blade knife on a Lawn Mower calm FS 55. Video instruction, how to change the mowing heads of a brushcutter from a reel (fishing line) to a knife. Then repeat the previous assembly. With semi-automatic winding, the bobbins act as follows. The fishing line is passed through the hole inside, its ends are fixed in the holes on the body, collect it and press the button. In this case, the thread is easily wound in the right direction.

It is important to remember that the cutting surface must be protected from solid objects so that it does not wear out. Otherwise, it will be necessary to constantly stop and, having removed the bobbin, replace the spent fishing line. Let your work be not tiring and bring joy!

Read the same

How to thread fishing line into the trimmer reel: winding instruction

A gasoline or electric trimmer is an indispensable assistant in the arsenal of a modern summer resident or the owner of his own house.

How to Properly Install a Knife on a Trimmer Video

Thanks to these garden devices, you can easily mow down even a large garden plot. After acquiring this tool and doing a few tricks, many people think about how to properly wind the line onto the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since developers often do not fully reflect the instructions for replacing the fishing line in the instruction manual.

Preparation for winding fishing line

Prior to the winding process, it is necessary to remove the reel with fishing line from the housing. Depending on the manufacturer, power and type (electric or gasoline), there are three structural types of trimmers:

    Compact electric trimmers.

A tool of this type has a lower arrangement of the engine and head, which in turn has two side buttons for removing the bobbin. When pressed simultaneously, the top of the reel with fishing line is disconnected, and the bottom remains rigidly attached to the braid. Experts recommend disassembling on a flat area in order to prevent spring popping.

  • Moto and electric braids with a curved duralumin rod, not intended for use with a knife. As a rule, coils of such models are equipped with a special wing nut. Dismantling the spool should be done by holding the coil body with one hand, and twist the wing counterclockwise with the other.
  • Powerful gas trimmers and electric braids with a direct barbell.
  • Straight Bar Trimmer

    In such a model, it is possible to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To install the trimmer knife, it is necessary to combine the hole of the bobbin and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, it is easy to unscrew the housing by hand clockwise.

    Winding fishing line on trimmer

    The measured and accurate dismantling of the spool from the spit reel makes it possible to go directly to the winding of the fishing line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today, there are several varieties of reels, depending on the number of antenna line fishing line and methods of refueling:

    1. Trimmer head with one working antennae;
    2. A bobbin with two antennae fishing line;
    3. Auto winding reel.

    Single-Barrel Trimmer Coil

    Single-mustache coil brush

    Many owners and specialists note the simplicity of operation and refueling reels with one mustache. Depending on the manufacturer, the length of the fishing line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and winding is made in the direction opposite to the working rotation of the bobbin. Most coils on the outside of the case have marks in the form of arrows that indicate the direction of movement of the trimmer bobbin.

    After winding, you need to leave a free end of 15-30 cm to enhance centrifugal force, which is crucial when removing the trimmer line in automatic and semi-automatic reels. We pass the left end through the working hole of the coil and assemble the head.

    Double Antenna Trimmer

    Two groove head

    After removing the spool from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but with careless refueling in a twin groove, there are problems with operation. Due to the likelihood of weaving adjacent tool strings, a situation may arise when it is impossible to remove new ones after wear of the working antennae.

    Regardless of the number of streams for refueling, a fishing line from 1.5 to 3 meters long is taken. Winding must be done in the direction opposite to the rotation of the head, since winding in the direction of travel will cause the line to not be removed from the reel. After the fishing line is tucked into the trimmer coil, free ends (15-30 cm) are threaded through special holes. Next, we collect the head in the reverse disassembly order and check the performance. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the guard will cut off the excess.

    Trimmer head with automatic threading

    Types of Trimmer Heads

    In some models available on the market, a reel with an automatic winding mechanism is installed. It is enough for the owner to correctly tuck and fix the ends in the head, and the tool itself will perform the winding operation when it is switched on in the operating mode. It is almost impossible to wind a fishing line into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of an automatic trimmer head include the ease of refueling fishing line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and high cost.

    How to reel a fishing line on a trimmer reel: key points was last modified: June 28th, 2018 by Administrator

    How to Install a Fishing Line on a Trimmer EVDIRAL.RU

    How right win line to the trimmer coil, if you haven’t done it before. Learn from the article how to wind the line onto the trimmer reel correctly.

    Many, having developed a factory fishing line on a trimmer not so long ago obtained, try to rewind the newest, but they cannot, because they do not know how to wind the line onto the reel coil (bobbin) correctly. As if the annotation is, but still does not work. Let’s try to deal with this issue in this article.

    So that win line, it is necessary, for starters, to remove the coil from the trimmer so it will be more convenient. The removal method will depend on the type of trimmer.

    Remove the coil from the trimmer

    On small electronic trimmers with the bottom position of the motor (when it is at work near the ground), the coil usually has two buttons at the edges. Click on them and disconnect one half of the coil body from the 2nd, which remains on the trimmer. Together with the first half, the inner part, on which it is specifically wound, is removed fishing line. When parsing, be careful: there is a spring inside that can fly out and get lost.

    On electric and petrol trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to grab the coil body with one hand, and with the second hand you need to start turning the lamb on it. It is he who fastens the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, being careful not to lose the spring inside.

    Read the same

    On electric and petrol trimmers with a straight rod and a gearbox at its end (in addition to fishing line, you can also install a knife on such trimmers) we look for a hole under the coil, insert a screwdriver into it, for example, rotate the coil quietly until the screwdriver penetrates even deeper, and the coil will lock. Now twist the entire coil clockwise (since the thread is left) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted by a lamb. If the coil is on latches, then we press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just twist the lamb. There may also be a third type of connection of two halves of such a coil: with it you need to grab the bottom part with one hand and the upper one with the other, and begin to turn them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.

    How to wind a fishing line on a mowing head of a trimmer or Lawn Mower

    The video shows in detail how to reel fishing line to the reel trimmer or Lawn Mower. Refueling with mowing line.

    How to wind a fishing line on a mowing head of a Lawn Mower (trimmer)

    Find out more on our website: Subscribe to our YOUTUBE channel! Always glad to cooperate!

    than 200 types of trimmers in one place at the lowest prices. Click and see

    Read the same

    Now, having removed and disassembled the coil, we proceed, in fact, to winding.

    Winding process

    If your coil is designed to work with only one antennae, then everything is simple. You need to rewind 2-4 m fishing line (depending on the size of the reel), find on the inside reel fixing the fishing line hole, insert one end of the fishing line there and start winding the fishing line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate an arrow, in which direction to wind the line. After winding up the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inside of the reel and designed so that the fishing line does not unwind at the time of collection of the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the reel. Next, take the outer part of the reel and thread the outer piece of fishing line into the existing hole, assemble and put the reel back on trimmer.

    Video: How to Properly Install a Knife on a Trimmer Video


    If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we see how many grooves are available for winding fishing line. There may be one or two. If there is one groove, then both antennae are wound along this same groove. If there are two grooves, then each antennae is wound in its own groove. A coil with one groove must have a through hole into which it is inserted. fishing line. Unwind 2-4 m of fishing line, thread it through this hole so that on each side of the fishing line sticks out equally. And at the same time we wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside coils. We leave a little fishing line unwound, we fix the ends in special grooves, and if we do not hold them with our fingers. Pass both ends into the holes on the outer coil body. We assemble the coil and attach it to the trimmer.

    If there are two grooves, we fold the piece of fishing line 2-4 m long in half, insert the loop obtained at the bend point into the groove between the two grooves, and simultaneously wind both ends of the fishing line in each groove. Further actions are similar to the previous option.

    There are still reels in which the line is threaded through the through hole on the inside, the ends of the line, without being wound, are completely threaded through the holes on the outer casing of the reel, the reel is assembled and the button that you usually press is rotated to release the line through the extent of its wear. Turn the button inside the line itself is wound. At the same time, turning it in the wrong direction will not work, since it can spin in only one direction. If you adapt, then on such a reel you can wrap the fishing line, even without disassembling it, you just need to combine the through hole of the inner drum with the holes on the outer casing of the reel, and then thread the fishing line into them.

    That’s all for the matter. Good winding!

    Read the same

    How to Install a Fishing Line on a Trimmer Coil Video

    on the trimmer coil?

    Despite the fact that garden equipment has been used for a long time, for some owners of private houses this is still a novelty. That is why questions often arise about how to properly wind a line on an electric one.

    This, in fact, is a simple operation, but all its steps must be performed correctly to achieve the desired result. over, in the instructions for use, only a few manufacturers give an answer to this urgent question. Study the article and find out how the fishing line is wound.

    The order of winding the line on the trimmer coil

    First of all, you should know that trimmers have different working attachments. The coil can be designed for different lengths and line thicknesses. this point should be considered when purchasing supplies.

    Related posts

    So how do I load the fishing line into the trimmer reel? All work is divided into several stages:

    1. First you need to disassemble the trimmer head.
    2. Unscrew the nozzle by turning the drum to the right.
    3. Press your fingers on the two latches located on opposite sides of the tafole and remove the top cap of the nozzle. You can remove the cover with a screwdriver. This must be done carefully: there is a spring on drums with automatic feeding of the trap, which can forcibly reset the lid along with all the contents of the coil.

    How to reel fishing line on the mowing head of a trimmer or brushcutter

    AT video shown in detail how to wind fishing line on the trimmer coil or Lawn Mower. Gas station fishing line mowing

    Manual mower. Replacing fishing line in the reel.

    In this video, I show how easy and easy to reel. fishing line on the reel manual mowers yourself

    Related posts

    When you turn on the trimmer, the extra line itself is cut off by the cutting edge.

    As you can see, winding the line on a cut coil is not difficult: the main thing. do everything right. And here are some more tips to help you when choosing a line, winding and subsequent work:

    • A line of different thicknesses and with different cross sections. The best option for winding is the "native" line for this model;
    • Do not use fishing line or metal cables for the trimmer. Such a replacement may seem effective, but it is very dangerous. By jumping off the working trimmer, the cable can seriously damage not only the mower, but also those around it;
    • The tray is trimmed when the working trimmer comes in contact with hard objects. Try not to allow this, otherwise you will have to stop every time, turn off the device and rewind the line on the reel;
    • ordinary grass is used to cut grass lawn, and for coarse weeds. pigtail line. It is more durable and will not be constantly reduced.

    Related posts

    How to install a fishing line on a video trimmer

    Any self-respecting summer resident is required to have at their disposal a summer trimmer, or as they also call a Lawn Mower. However, in order to maintain the trimmer in working condition, you must be able to replace the fishing line in the trimmer correctly to maintain healthy.

    In this manual, we will consider removing the trimmer coil and replacing the fishing line in it. Terms used in the manual:

    Video guide to replace the fishing line at the trimmer at the end of the article

    Before starting to replace the fishing line, you should separate the mowing head of the scythe in which the fishing reel is located. This element is attached to the end of the stick of your trimmer and removed by unscrewing it in the direction where the arrow on the reel points.

    After to remove the mowing head with a coil, you must open it. First of all, you need to find a latch mechanism on the coil. It is part of the reel and is like 2 clamps, clicking on which you can open the reel and get to the place where you want to wind the line.

    Open the mowing head and take out the reel for winding fishing line

    You can open the coil with your hands or with a screwdriver or other tools with which you can pry the snap elements.

    Before starting to replace the trimmer fishing line, it is worth measuring a few meters of fishing line; What kind of fishing line to use is written in the documentation of the trimmer or directly on the Lawn Mower itself.

    Mostly used fishing line with a diameter of 2-3 mm; The diameter of the fishing line depends on how large the stems are in your grass. If it is necessary to mow the mugs, then in this case it is better to choose a fishing line with a diameter of 3 mm or more, if your trimmer provides for this.

    After we measure out the necessary piece of fishing line, fold it in half and hold it with your fingers even stronger from the side of the scrap. In the same way as when inserting threads into a needle.

    How to wrap fishing line on a trim reel?

    Then you should find on the reel slots for attaching fishing line; place the fold into the fishing line.

    Slot in reel for attaching fishing line

    Then we wind the line on the reel in the direction indicated on the reel itself. As a rule, the fishing line is wound counterclockwise, but if this information is not on the reel, then you should contact the trimmer for information.

    Winding fishing lines on a Lawn Mower reel

    We wash the fishing line until there are two ends of the sizes of 10-15 centimeters. Winding the fishing line of the trimmer occurs with little effort and uniformity.

    These ends must be inserted into the holes of the mowing head. Then we insert the coil into the mowing head, fix it and screw it onto the trimmer stick. Also, the excess part of the fishing line should be cut off if it is larger than the diameter of the protective casing.

    The ends of the fishing line should be cut with scissors or bite off with teeth.

    We advise you to watch the youtube video on how to properly replace the fishing line of the trimmer, by wrapping it on a coil of Lawn Mower.

    Your opinion

    My fishing line doesn’t want to leave, I constantly have to disassemble and pull out the antennae, either such a braid, or I am “such”

    Your opinion Cancel reply

    The informative news site Dez.ru covers only important and interesting trending news and events, He publishes interesting articles and notes on various topics: dates, events, life hacks and useful articles answering the questions “how to do”, “when will be”, “what is needed for. ”, Etc. get answers to questions using the search on the site or go to the desired category of the site. news or article. Most news is exclusive or translations from trust English-language news sites. Due to the general negative atmosphere in the international arena, we try to publish only good and kind news filled with positive.

    The interesting articles posted by the authors are of a completely diverse nature, in most cases revealing the essence of the issue giving a short and at the same time complete answer.

    How to change the fishing line in the trimmer and which is better to choose

    Since we considered the choice of the trimmer in the previous article, today we will tell you how to properly trim the trimmer with a fishing line, and which is better to choose based on the working conditions.

    After you bought a trimmer and began to use it actively, sooner or later the question will arise about replacing the fishing line, since this is the most wearing element in the tool, then intensive use of the trimmer will lead to frequent replacement of consumables.

    What types of woods are

    The most common type of fishing line that fits almost all types of reels is round cord. This is an ordinary fishing line suitable for mowing juicy grass, but mowing dead wood with it will be much more difficult, and even more so it can not cope with the bush.

    As a rule, the diameter by which young grass can be mowed does not exceed 1.6 mm. The thicker the thread, the more coarse grass it can overcome.

    There are fishing lines with sharp edges in the form of an asterisk or square, this option is more suitable for mowing dry grass just due to the existing sharp edges, but its disadvantage is more wear and tear and is inferior in strength to round cord.

    There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product produces less noise, but they are used only on benders, since the exit of such a thread from the reel is difficult, it is used most often with discs in which segments are inserted. The disadvantage of this product is its fragility.

    Most often in gas trimmers with an engine power of more than 1.5 hp apply cords with a metal cable inside. This thread is ideal for mowing dry grass and small bushes. The presence of a core positively affects the wear resistance of this material. The disadvantage of such a cord is its price, which is significantly higher than the listed opponents.

    How to Fill a Fishing Line into a Trimmer Coil

    It takes about 10-15 minutes to wind the line. What is a trimmer coil? Plastic case with a cassette inside, on which there is a special hook for convenient winding of fishing line. Almost all trimmer coils have a similar mounting principle, this is the central screw-button, when pressed, it becomes possible to pull the fishing line of the required length. The photo below shows some examples of different coils for trimmers.

    The bobbins of the trimmers, the motor of which is located near the ground, have a different mount to the axis of rotation, they have two buttons on the spool located on the sides that need to be pressed, otherwise the thread replacement is no different from other cassettes.

    The principle of the correct winding of the fishing line is similar in all of the above cases, so for example, consider the standard version with two antennae.

    To remove the reel with fishing line, it is necessary to unscrew the screw located in the center, but note that the thread there is left, so you have to turn it clockwise, this is done specially so that during operation it does not open under the influence of centrifugal force.

    Next, using a screwdriver, disassemble the head and take out the reel, on which the fishing line is directly wound. Having measured the necessary length and folded in half, you need to fill the fishing line into the reel, removing, in the end, its ends opposite each other (for this there are special slots for fixing).

    After this, it is necessary to assemble the head in the reverse order by threading the ends of the cord into two corresponding holes.

    If you have doubts or it’s not entirely clear how to charge the fishing line to the trimmer, we recommend that you watch the video: how to wind the fishing line into the brushcutter correctly. In this video, the instructor will open the trimmer head in steps, measure out the required amount of fishing line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.

    Thanks just fine

    You are welcome. Glad to be able to help. &# 128578;

    Everywhere they tell you how to wind fishing line. But we don’t have to remove this box from Champion ET450 at all, the electric trimmer. There you need to drown the button and rotate counterclockwise and nothing. There is not enough hand effort and there is especially nothing to grab at, so everything is narrow. Lubricated with engine oil, although plastic does not make sense to lubricate. Maybe someone has encountered such a problem? Is it possible to disassemble everything and besides it is not clear how.

    Proper winding of fishing line on the trimmer reel

    How to wind a fishing line into a trimmer?

    When refueling a fishing line for the first time, this process may seem rather laborious, but with time and dexterity the task is solved much faster.

    In order to fill the line, you must:

    • Take the coil, unscrew its cover. On some coils, a thread was made to the left, so the cover must be unscrewed in the necessary direction.
    • Measure out five meters of fishing line;
    • Fold this segment in half, that is, determine where the middle is;
    • Next, place this middle of the fishing line in a special hole on the reel;
    • Wind the line to the side where the arrow points;
    • If there are two places for winding, then the first part of the fishing line should be wound on one half of the reel, and the second part on the other half;
    • Push both ends of the fishing line into the reel holes;
    • Screw on the cover.

    What kind of fishing line is used for the trimmer?

    There are several types of fishing line:

    • The most durable is round;
    • For mowing soft vegetation. curly;
    • For mowing thin grass. with notches;
    • Special. suitable for certain types of trimmer.

    The cross-sectional view of the cutting thread should correspond to the vegetation that needs to be mowed.

    If it is necessary to replace the fishing line, then it is necessary to select exactly the type that is recommended by the manufacturer of this particular trimmer model, that is, the thickness of the cutting thread should be suitable for the engine power and the size of the unit.

    It is better to choose a specialized cutting thread. It is worth soaking the fishing line for a while, if you plan to replace it in the reel.

    After soaking, it acquires an elastic look and becomes stronger.

    The cutting thread can be made of various components. The most common among them is nylon.

    This material is characterized by a high degree of wear resistance, the ability to withstand various temperatures and high loads.

    Nylon fishing line can be stored for a long time, it does not dry out and does not lose its strength.

    Therefore, its service life can be quite long.

    Coils or heads for Lawn Mower have a different structure:

    How to catch more fish?

    1. Single-stringed. In the modification of such a trimmer there is only one working line. Such an aggregate is used mainly for small jobs, such as trimming grass.
    2. Two-stringed. They can be either automatic or semi-automatic. Here the package includes two strings. Such a trimmer is used for mowing and clearing areas.

    Instructions for the correct winding of the thread on the trimmer spool:

    1. First of all, you need to disassemble the head. To do this, press the latch and turn the cover to the side. Next, the spool is removed.
    2. Measure the desired amount of cutting thread and insert it into the slot.
    3. Wrap fishing line on both sides in the direction of the arrow.
    4. The ends of a length of 15 cm should be left not wound.
    5. These ends are inserted into opposite slots.
    6. Then the ends are fixed in the hole on the head.
    7. Then the spool is carefully inserted into the case, To do this, gently press it.
    8. If necessary, the remaining ends of the thread can be pulled out. To do this, first pull one end of the thread, and then the other so that they can easily pass through the slots on the head.
    9. Now you need to assemble the grooves on the case and tighten the cover.
    10. Then press the spool and try to twist it all the way. If you hear a click, then the spool clicks into place.
    11. Next, you need to stretch the free ends of the thread to the end.

    How to remove the coil from the trimmer?

    To change or wind the cutting thread on the spool, it must be removed.

    The complexity of its removal depends on the model of the tool:

    1. Low engine tool. The motor here is almost near the ground. To remove the coil, you need to press the buttons located on the side of the trimmer. After pressing these buttons, the housing opens, where the reel with fishing line is located.
    2. Curved Bar Trimmer. Here it is necessary to turn the special lamb counterclockwise. After that, the coil and the spring in it are removed.
    3. Straight bar tool. The bar is held motionless with a screwdriver or other object. Turning it clockwise removes it. Then they disassemble the tool into parts and take out the bobbin.
    1. If you use a tool with one antennae, then you will need about four meters of thread. This thread is passed into the hole inside the spool where it can be fixed. Next, one end of the fishing line is directed in the direction of the arrow. Then the end of this thread is fixed in the groove, which is located in the bobbin. This is necessary so that the thread could not unwind when assembling the coil. In the absence of grooves, you should hold the fishing line with your hand and collect the reel.
    2. If a tool with two antennae is used, then first you need to check the number of grooves available.

    If the reel is equipped with a semi-automatic mechanism, then wrap the fishing line as follows:

    1. The thread is threaded into the hole that is inside;
    2. Fasten the ends of the thread in the grooves on the body.
    3. The coil is assembled and a special button is pressed;
    4. After that, the line itself starts to wander in the right direction.

    You must always remember that the cutting thread must be protected from solid things. This will extend its service life.

    If you do not adhere to this rule, you will often have to stop work, remove the spool and change the thread to a new one.

    Threading reels with various types of bobbins

    With two-string automatic heads:

    1. First you need to press the clip until it clicks, remove the cover.
    2. Gently turn the spool so that she can disconnect from the holder. Remove her.
    3. Measure two pieces of cutting thread of the same length. To further work was easier, the ends of the fishing line must be cut at an angle. Take one end and push it into a special hole in the coil. It can also be slots, grooves, clamps, etc.
    4. Next, in the direction of the arrow, you need to wind the fishing line, and quite tightly and evenly. In a special eye on the reel, you need to fix the end of the fishing line.
    5. The second half of the fishing line is subjected to the same operation, only on the other half of the coil.
    6. Next, install the coil in the trimmer head. And thread the remainder of the fishing line into the hole in the head.
    7. Then carefully straighten the thread and close the cover. If the fishing line turned out to be long, then it is better to cut off the excess. On each side should remain about fifteen centimeters.

    On a semi-automatic head:

    1. The thread is threaded into the hole that is inside;
    2. Fasten the ends of the thread in the grooves on the body.
    3. The coil is assembled and a special button is pressed;
    4. After that, the line itself starts to wander in the right direction.

    It is necessary to carefully and carefully thread the cutting thread into the machine, because not only the cleanliness of the garden plot, but also personal safety depends on the correctness of its winding.

    A few tips on how to properly thread the string into the trimmer

    • If the coil allows you to wind fifteen meters of thread, then you should not wind so much, ten is enough, that is, if folded in two layers, it will turn out five meters. With a different capacity of fishing line, it is worth using the same rule.
    • In the case when an ordinary round thread is used, it is better that it be a 3.3 mm diameter. If it is a figured fishing line, then its thickness should be less, for example 3 mm.
    • It is better to reel both pieces of fishing line on the spool at once, and it is necessary to start from its bend. It is important to prevent overlapping in the direction of the arrow. It is also important to be able to perfectly pull the thread. If the thread is tightened, then it can go lapped. If not reached, it can twist. In order not to cut your hands on the curly thread yourself, you should wrap it with gloves.
    • No need to leave the ends of the fishing line long. This may cause it to twist.

    Now only pecks from me!

    I caught this pike with the help of a bite activator. No more fishing without a catch and looking for excuses for your bad luck! It is time to change everything. The best bite activator of the year! Made in Italy.

    Similar articles:

    Cancel reply

    For cooperation, please e-mail: [email protected]

    © 2015-2017 All rights reserved. Internet portal about fishing SuperKaras.ru

    Copying material is possible only with an active link to the site.

    . The detained poachers confessed and told the secret of their good bite. Fish inspectors did not find any prohibited equipment.

    How to thread fishing line into the trimmer coil? Video instruction

    Guaranteed production of a factory trimmer refill will inevitably require replacing the fishing line. Having a very rough idea of ​​how to fill the fishing line into the reel of the trimmer yourself, beginners are reluctant to take up this matter. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will facilitate this process as much as possible.

    Preliminary preparation

    First of all, for winding fishing line it is required to remove the reel (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of product itself:

    • Small electric trimmers with a working arrangement of the engine and the coil in the lower part, as a rule, have side keys on both sides of the bobbin. By pressing them simultaneously, the upper part of the reel, together with the internal contents for winding the fishing line, is disconnected, while the lower one remains on the trimmer. It is advisable to disassemble the bobbin on an even smooth place so that the spring included in the design does not pop out and is not lost;
    • electric and gasoline trimmers with a curved rod without the possibility of installing a knife, as a rule, have coils with a special wing: in such designs, you should hold the spool in one position with one hand and rotate the locking reel on the wing nut with the other counterclockwise. After disconnecting the nut, the entire reel is removed.
    • electric and petrol trimmers with the possibility of installing the knife on a straight bar (for example, Calm trimmers) have a hole under the bobbin. For the motion of the rod to be stationary, a screwdriver or other suitable object is inserted into this hole and with a slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body scrolls clockwise (with the left thread) and is removed from the trimmer.

    For the second and third cases, the coils, depending on the design, are disassembled in various ways. In bobbins with a lamb, a lamb is twisted, in coils with latches, latches-clamps are pressed and one part of the coil is released from the other. If the halves of the spool are threaded, it is enough to turn them by hand in opposite directions until they are completely unscrewed.

    Want to see? Rating of the best brushcutters!

    We carry out winding fishing line

    Slowly completed disassembling the spool reel without losing its spare parts allows you to go to the main task. winding fishing line into the reel. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

    Coil with one working antenna

    The easiest option and a simple sequence of actions:

    1. The dimensions of the bobbin and the length of the original factory winding determine the recommended fishing line length for winding. 2. 5 m.
    2. One end of the fishing line is inserted into the fixing technological hole located inside the spool.
    3. The fishing line is wound on the drum in the reverse direction of rotation of the spool on the trimmer product. as a rule, on the inner side of the bobbin an arrow indicates which direction the winding is going.
    4. A small section of fishing line is left free to bring it out. it is fixed in a specialized groove on the inside of the reel, designed to hold the winding when assembling the spool in working condition.
    5. The left end of the line is passed through the hole on the outside of the bobbin.
    6. The bobbin halves are assembled and put on the bar of the trimmer.

    Coil with two working antennae

    In this type of spools, you should determine the number of grooves for winding fishing line lying on the inside of the reel:

    • one groove. both antennae are wound together along one groove;
    • two grooves. each antennae is wound on an individual groove.

    For both cases, a 2-3-meter-long fishing line is taken. In single-channel reels, the fishing line is pulled into the through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the side of the bar. the correct direction of winding is usually indicated inside the arrow. In the presence of fixing grooves, the ends of the fishing line are threaded into them or held by the fingers of their free hands, threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the bar of the trimmer.

    The difference between winding fishing line in two-groove reels is that initially a piece of fishing line 2-5 m long is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each in its own groove, the fixation of the antennae and the reel assembly are similar to the one-groove variant discussed above.

    The first implementation of this procedure may seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

    The video below will clearly show how to put the fishing line into the reel of the trimmer and wrap it correctly. this operation is not difficult and with some patience will certainly succeed:

    Automatic reeling of fishing line

    There is a variety of coils in which the automatic mechanism makes winding on its own. from the user it is enough just to properly fill the line. The fishing line is passed through the hole on the inside of the case, its antennae without winding is passed through the hole on the external case, the spool is assembled, and when the winding button is rotated, the line inside is wound up independently. In such a spool, it is impossible to make the winding incorrectly: the mechanism itself will determine the correct direction, since it can only turn in one direction.

    How to Use a Grass Trimmer Properly

    IMPORTANT! To bookmark an article, click: CTRL D

    How to use a trimmer lawnmower

    Surely, many owners of summer cottages have encountered a problem when they need to clear a certain area from weeds, on which, for example, fruit trees grow densely. It’s not possible to wield an ordinary scythe here with your hand. you can’t swing it off, the chopper is long and laborious, the lawn mower will not pass. But there is still a solution: you can use a trimmer (scythe), which has long been used abroad for mowing grass in hard to reach places.

    How to use a trimmer lawnmower

    Before you purchase or rent a trimmer or a brushcutter, you need to decide for what purpose you need it. If the proposed area of ​​grass mowing is from four to six acres, it is better to use a trimmer. If the area of ​​the cultivated area is more than six hundred parts. you need a Lawn Mower. Today we will focus on the first option. the trimmer.

    Trimmers come in two forms:

    • Electric trimmers are less powerful, suitable for work in a summer cottage, where it is possible to connect to the mains for direct power supply or recharging batteries.
    • Petrol trimmers. equipped with gasoline engines, they are more autonomous and are suitable for those gardeners and gardeners who do not have the opportunity to connect to the outlet. In addition, in terms of energy reserves, gas trimmers give a head start to electric ones. they work 10-15 minutes longer than “outlet” ones.

    Petrol trimmers

    As a rule, gas trimmers are equipped with two-stroke engines, the power of which is about two horsepower / 1.5 kW. By the location of the engine, such devices are divided into upper motor and backpack.

    Upper-motor gasoline trimmers are suitable for mowing grass in small areas with uneven terrain. Due to the fact that the engine on such a device is located on the upper part of the handle, it is convenient for them to balance and reach hard-to-reach areas. Such trimmers, in particular, are produced by the German company Solo.

    For example, the Solo 142B is designed to work in large areas with uneven terrain. She has an ergonomic handle-like handle. At the top of the trimmer is a two-stroke, 2.6-horsepower motor, at the bottom. a cutting mechanism. Depending on the stiffness of the mowed grass, one of two cutting tools can be used: a three-toothed knife (for hard grass, small bushes) or a fishing line (for thin-stemmed weeds). The volume of the fuel tank of such a trimmer is 0.7 liters, this amount of fuel on average is enough for 45-60 minutes of operation.

    Gasoline Lawnmower Trimmer

    Trimmers with a knapsack engine and a flexible shaft are used to mow grass in large areas. They are more convenient to use, since their engine (with a power of the order of 2.5–3 hp or more) is fixed behind, which allows the mower not to get tired during the processing of large-scale sections.

    The model of the Italian company Oleo-Mac 446 BP Ergo is an example of such a knapsack device. Vibrations fastened behind the back on special backpack mounts of a powerful motor (2.8 hp) are practically not felt during operation. thanks to a special vibration suppression system. The fuel tank of the device has a volume of 1.5 liters, which is enough for 1.5 hours of operation. The set of such a device includes several types of knives, which allows you to clean grass of any stiffness, shrubs and even small trees.

    Electric trimmers

    This type of trimmer is what any gardener who has a small summer cottage needs to mow soft-stem weeds or lawns. By their design, electric trimmers are divided into upper and lower motor.

    Upper motor electric trimmers, such as gasoline ones, are designed for mowing grass in areas with uneven terrain. Another important distinguishing feature of such devices: they can mow wet grass, while this is contraindicated for lower-motor electric trimmers. there is a risk of short circuit.

    Electric trimmers

    An example of an upper-motor trimmer is the model of the German gardena manufacturer Gardena. ProCut 800. The device is equipped with an 800-watt electric motor that is powered by a wall outlet. They can process small areas up to six acres. The cutting mechanism is fishing line.

    Lower-motor electric trimmers are usually equipped with small-capacity rechargeable batteries, and such devices are intended for mowing grass in areas with a flat relief.

    The Gardena AccuCut 400 Li is equipped with a lithium-ion battery (18 V / 1.6 Ah) and is designed for short-term (enough charge for 30 minutes of work) grass mowing on flat areas. The rotary handle of the device helps mow grass on the edges of the lawn.

    How to use a trimmer

    Step 1: Install the cutting mechanism

    Depending on the type of weed grass, we choose a cutting tool: for soft-stalked grasses. a fishing line, for hard-stemmed and small shrubs. a knife. Unscrew the nut securing the cutting mechanism and install the cutting tool. Tighten the nut. the mechanism is ready to work.

    Note: some trimmers do not have interchangeable cutting tools, so you can start working with them right away.

    Step 2: Preparing the Trimmer for Use

    If the trimmer is electric. we charge the battery or turn on the motor in the network. If gasoline. fill the tank with fuel. Then, depending on the type of trimmer. we adapt it to ourselves (upper-motor. is hung with a loop on the shoulder, knapsack. for the shoulders, lower-motor. we take the handle). We hold the trimmer over the grass so that its cutting mechanism is parallel to the treated area. We start the engine.

    Grass mowing with a trimmer is carried out with simple movements. It is important to remember that the cutting mechanism of the device rotates counterclockwise, so that the mowed grass will fall on the already treated area. The first is from right to left in front of us (this is how we cut off the top of the grass). The second is from left to right (this is how we remove the rest of the grass).

    It is better to divide a large area of ​​the cultivated area into squares, and mow grass on them, moving from one to another on the outside of each square.

    When mowing grass on the slopes, it is recommended to mow from below, moving parallel to the sloping area. We reached the edge, went back, became a little higher. and we repeat the same route. until the site is completely mowed.

    For mowing grass on a site where there are trees, it is better to use a forest cutting mechanism, and you need to mow, passing the site along the perimeter, bypassing the tree around the trunk.

    Step 4: Finish

    After mowing all the grass in the area, you need to turn off the engine, remove the trimmer (for shoulder and knapsack devices), clean the cutting mechanism of the rest of the grass.

    How to mow grass with a trimmer?

    The main thing is to correctly adjust the trimmer belt so that the drum with fishing line does not crawl along the ground.

    Properly make a gasoline-oil mixture.

    Do not use too thick fishing line. it picks up speed and overloads the trimmer.

    Do not be afraid to give him speed.

    Do not wind too much fishing line on the drum, and do not wind it too much.

    Stop and clean from time to time "the basket".

    Lubricate the trimmer cable and gear (if any) with a grease gun.

    The technique of mowing grass with a trimmer is not very complicated and takes into account the need:

    • Decide how exactly you are going to mow. It is possible to fold, crosswise.
    • choose a place so that a bald spot does not appear as a result and the site looks harmonious
    • understand what exactly you are going to mow, and depending on the choice to put the right knife. They are different. For example, hay or weed. You also need to set the speed.
    • Of course, it is necessary to prepare both clothing and protective equipment. Whatever you are an experienced mower man, but glasses must be worn. and don’t forget the headphones and long clothes.

    Video: How to Use a Grass Trimmer Properly


    All the details of the technique are on the video how to mow with a trimmer.

    First of all, inspect the area that you have to mow. Cut off bushes or large flowers that cannot be cut on your own.

    Always start with a light area where there is little grass. See if there are slopes or ditches in the area. The easiest way to mow across the slope.

    Determine the direction of the grass. Mowing is easier if the grass is tilted forward.

    As for clothes, you should always wear glasses and boots. Also anti-vibration gloves do not interfere.

    Use different knives depending on the density of the grass.

    One more tip: try to mow at the same speed. This way your mower will last longer. If you stop and immediately pick up speed, then the trimmer will wear out faster.

    If you decide to mow the grass with a trimmer, it is important not only to carefully prepare for the cutting process. It is also important to be able to handle the trimmer well and have a protective suit. In addition, you must be able to adjust the trimmer.

    Correct mowing with trimmer:

    • choose the fishing line correctly. For different tasks, there are two different objects. fishing line and knife. Too wide fishing line is undesirable, as this will give overload to the trimmer. As a rule, on a simple site fishing line is enough.
    • when cutting is installed (fishing line or knife), it is necessary to tighten and fasten the nut.
    • Check the charge or availability of fuel. Put on the belt comfortably.
    • movements when mowing with a trimmer should be thought out. The algorithm is: right-left-left-right. This will give the maximum result. Yes and be attentive to work. It is necessary to control that there are no children or animals near you. You should also wear a mask to protect your eyes.

    First, adjust the trimmer belt so that the drum does not touch the ground. Further, it is important to remember that due to the thick fishing line, the trimmer will be overloaded, so do not overdo it with the thickness.

    A lot of fishing line on the drum is not worth winding.

    Remember to periodically clean the trimmer.

    Lubricate the cable with a solid oil.

    The trimmer is very convenient as it can be used in a variety of places, including complex terrain and areas near trees. If you mow tall grass, first start with the protruding tops and then continue with the bulk.

    Use the trimmer as intended. An electric scythe (that is, a trimmer) is good because it copes well with its work in hard-to-reach places. Therefore, the trimmer can be used near trees, fences in relief areas. And not only for mowing the lawn, but also ordinary grass.

    The main thing is to ensure that the weeds do not have time to give the seeds and mow them in time.

    If you did not have time to mow the grass until the moment it gave the ears, then first mow the tops of the ears and burn them. And only then mow the grass itself, and put it into compost.

    In almost all trimmers (if there are no special ones), the fishing line or the disc rotates clockwise. That is why it is better to mow the grass with a movement from right to left (a movement that resembles movement when mowing with an iron scythe). It can be mowed by tilting slightly towards mowing.

    You need to mow with calm movements, not jerks. Mow grass half the length of the fishing line. If you grab more, the trimmer can handle it, but grass can clog the space between the coil and the tube.

    Mow, squeezing the gas to full.

    Before mowing the grass, first adjust the fishing line and firmly fix it in your cavity so that the fishing line does not hang out and go here and there. Then fill the fuel accordingly (if you do not have an electric trimmer) which consists of special oil and gasoline. Next, start mowing the grass with smooth movements (not fast) to the right and left. Do not try to chop thick stems of plants often, as the fishing line will instantly end, and you will have to adjust the reel again. In dense places, the main thing is not to spare gas)

    The trimmer from the company Varyag koshu according to the instructions:

    Step 1. Install the cutting mechanism.

    Depending on the type of weed grass, we choose a cutting tool: for soft-stalked grasses. a fishing line, for hard-stemmed and small shrubs. a knife. Unscrew the nut securing the cutting mechanism and install the cutting tool. Tighten the nut. the mechanism is ready to work.

    Note: some trimmers do not have interchangeable cutting tools, so you can start working with them right away.

    Step 2. Preparing the trimmer for work.

    If the trimmer is electric. we charge the battery or turn on the motor in the network. If gasoline. fill the tank with fuel. Then, depending on the type of trimmer. we adapt it to ourselves (upper-motor. is hung with a loop on the shoulder, knapsack. for the shoulders, lower-motor. we take the handle). We hold the trimmer over the grass so that its cutting mechanism is parallel to the treated area. We start the engine.

    Action 3. Mowing.

    Grass mowing with a trimmer is carried out with simple movements. It is important to remember that the cutting mechanism of the device rotates counterclockwise, so that the mowed grass will fall on the already treated area. The first is from right to left in front of us (this is how we cut off the top of the grass). The second is from left to right (this is how we remove the rest of the grass).

    It is better to divide a large area of ​​the cultivated area into squares, and mow grass on them, moving from one to another on the outside of each square.

    When mowing grass on the slopes, it is recommended to mow from below, moving parallel to the sloping area. We reached the edge, went back, became a little higher. and we repeat the same route. until the site is completely mowed.

    For mowing grass on a site where there are trees, it is better to use a forest cutting mechanism, and you need to mow, passing the site along the perimeter, bypassing the tree around the trunk.

    Step 4. Finish the job.

    After mowing all the grass in the area, you need to turn off the engine, remove the trimmer (for shoulder and knapsack devices), clean the cutting mechanism of the rest of the grass.

    How to work with an electric grass trimmer

    When choosing equipment for a summer cottage, it’s not always worth chasing powerful and dimensional devices. The power of the tool is, undoubtedly, an important parameter, but it certainly pulls the increased weight of the device, its large size, as well as the high price and increased fuel costs. But that’s not the point. If you have a small garden in which fruit trees are densely planted or a small lawn with flower beds and shrubs, then cleaning it from weeds and mowing grass neatly is clearly an impossible task for any lawn mower. In such cases, even a hand tool. an ordinary scythe and that will not help: you just can not swing it, bumping into tree trunks. The ideal solution in this case is a good and inexpensive electric trimmer. It is so light, convenient and easy to operate that it always becomes a favorite among women and older people. A lightweight, quietly buzzing electric motor, a handle with convenient handles and a nylon fishing line tucked into the spool are the main components of the electric trimmer.

    Electric trimmer efficiency

    A trimmer that works from a household electrical network, relevant on a plot of four to six acres, planted with trees, flowers, shrubs. It is convenient for them to carefully mow the grass near the house or along the curb, mow the paths, and an environmentally friendly motor that does not produce exhaust, gas and burning will even make it possible to remove weeds in any indoor room. a greenhouse or greenhouse.

    The trimmer cable limits the grass mowing radius, but can be increased with a standard extension cord. If this length is not enough for you, or the power supply parameters do not contribute to the normal operation of the electric motor, then you can purchase a kind of electric tool. a cordless trimmer. It works autonomously, the built-in battery lasts for half an hour or an hour of intensive work. it is enough to mow the trees in the garden.

    The motor at the trimmer can be placed at the top of the tool or at the bottom. Upper-motor trimmers work well on bumpy and uneven terrain. They are also well balanced and can work with tall and wet grass. a short circuit will not occur. The convenience of working with it is also enhanced by a single-arm loop, which is hung on the shoulder.

    How to Use a Grass Trimmer Properly

    The lower motor trimmer can only be used for wet grass and for flat areas. Often, lower motor trimmers operate on a battery.

    The household trimmer is the easiest to use and at the same time very effective tool. It seems that there is nowhere easier. to plug the instrument into a power outlet and work. But still there are some nuances that you need to know in order for the trimmer to work long and productively.

    If there are a lot of trees on the site, mow only with fishing line, otherwise you can cut the tree trunk with a knife. In such a garden, it is best to mow around the perimeter, bypassing the tree in a circle.

    5. Shutdown. Turning off the engine and removing the shoulder straps is not a complete shutdown. It is necessary to carefully clean the spool and knife from the remnants of grass. Then fold the trimmer if it is telescopic or collapsible and hide it until the next mowing.

    The fishing line is wound around the spool inside the reel, and its tips are exposed. When mowing, the spool rotates, and the line, with this rotation, cuts off the grass. To release the tips you need to lightly tap the coil on the ground (semi-automatic system), there are automatic reels in which the fishing line is released by itself. When working with fishing line there are also several rules:

    In order not to damage the fishing line and reel. Try not to touch the reel and fishing line of various solid materials. paths, borders, fences. From this fishing line is prematurely shortened, the coil may be damaged or even jam the engine. The spool with fishing line should also not touch the ground.

    Mowing with tips is more efficient. If you mow the entire length of the fishing line, you can overload the engine. In addition, this reduces the efficiency of mowing. The tool must be held so that it mows only the ends of the fishing line. To do this, tilt it forward. towards mowing.

    Tall grass requires several mowing. If the grass is above 20 centimeters, then one mowing will not do here. It is necessary to mow two to three times, from top to bottom. This is done so that the grass does not wrap around the reel. Wound grass is a guaranteed overheating of the engine. If the grass is still wound, you need to stop the tool and clean it.

    The fishing line ran away and hid in a reel. This option when working happens if you did not release the line from the reel on time. After all, the line when mowing is erased and shortened. If you do not have time to release it, then stop the engine, turn off the tool from the network, and then disassemble the spool and pass the ends of the fishing line into the desired holes.

    What does the consumption of fishing line depend on? It must be remembered that the line wears out faster if the grass is tough. Therefore, you need to release it more often when mowing weeds and dry hard grass. Around the foundation of the house, near the wall and the curb, the consumption of fishing line will also be greater than directly on the lawn or near trees. It is worth considering: if you work carefully and accurately, the consumption of trimmer line will be optimal and economical.

    How to Properly Dilute Gasoline with Trimmer Oil

    The chainsaw engine is the "heart" of the tool, so it is very important to use a properly prepared fuel mixture.

    How to Properly Dilute Gasoline with Trimmer Oil

    Fuel mixture for a chainsaw It is prepared from two components. oil and gasoline. Chainsaws are equipped with two-stroke engines, so the oil is not added to the lubrication system (like a four-stroke engine), but directly to gasoline. At the same time, it is very important to observe the correct proportions of the ingredients, of course, in no case try to work on pure gasoline, because in this way you will very quickly “kill” the chainsaw.

    If we talk about which gasoline to pour into a chainsaw, it will optimally use fuel with an octane rating A-95, in this case, fuel economy can turn out disastrously. Often, European manufacturers indicate that A-90 or A-92 gasoline can be used, but in post-Soviet countries the quality of gasoline is inferior to European, so in our realities it is better to use better gasoline.

    As for the most proportions of a benzo-oiled mixture, then everything is simple: you must follow the instructions for the tool. All manufacturers of chainsaws indicate the necessary ratio in the instruction manual or in the instrument passport, in addition, the proportions for refueling the chainsaw may differ depending on the model of the chainsaw. As a rule, the proportion of oil and gasoline to a chainsaw of famous manufacturers is a ratio of 1:40 or 1:50, which means 1 part of oil for, for example, 40 parts of gasoline. Now arithmetic 1 liter of gasoline = 1000 ml of gasoline, divide by 40 and get 25 ml of oil. If you perform the same steps to the ratio 1:50, then we get 20 ml of oil per 1 liter of gasoline. As for budget-made Chinese chainsaws, the situation is slightly different. The ratio of gasoline and oil for chainsaw made in China 1:25, that is, 1000 ml of gasoline is divided by 25, we get 40 ml of oil. The thing is that in branded chainsaws a good assembly and the distance between the pistons and cylinders in the engine is much smaller than that of Chinese chainsaws, therefore the required amount of oil differs almost twice.

    Video: How to Properly Dilute Gasoline with Trimmer Oil


    In order to measure the correct portion of oil, use a regular medical syringe of sufficient volume.

    Another subtlety. In a dry canister for gasoline, first fill in gasoline, and then oil. On the contrary, the procedure is fraught with a poor quality fuel mixture, because the oil is more dense, sticks to the bottom of the canister. what a good mix.

    Be sure to prepare the fuel mixture in a can and pour ready-made special fuel into the gas tank! Never cook or mix directly in the fuel tank of a chainsaw!

    If the question of how to breed gasoline for a chainsaw figured out, then on storage conditions and shelf life of the fuel mixture It is worth saying a few words. It’s best and easier to prepare a 1-liter gasoline-oil mixture, it is recommended to do this immediately before working with the tool. The fuel tanks of chainsaws have a volume of 0.3 to 1 liter. In domestic use, in one session, the entire volume of the prepared combustible mixture is rarely used, so the remainder can be saved until the next session. It is necessary to store the fuel mixture in a special canister for gasoline, in a dry, dark place. It is optimal to calculate that shelf life of the finished mixture will be 7-10 days. The fact is that the oil currently on the market is not synthetic, but organic, that is, natural. After 10 days, all lubricating properties are lost, gasoline simply “eats” the oil. Naturally, it is no longer possible to use such fuel, this can cause breakdown and failure of the chainsaw.

    At the end of the work, it is necessary to drain the fuel mixture, start the chainsaw, the tool stalls (so that the saw has a dry carburetor) and now you can leave it until the next operation session.

    Unsuitable fuel mixture must be disposed of.

    How to Sharpen Stihl Chainsaw Files Properly

    The tooth of the chain planes the wood like a planer, and the thickness of the chips is controlled by the height of the limiter.

    How to Sharpen Stihl Chainsaw Files Properly

    Intensive work of the saw leads to a rapid blunting of the chain. Several sharpenings may be required within one day. The problem is aggravated by the fact that the tooth quickly becomes dull when it encounters the ground. It is enough to hook the soil once or twice, and the work can be stopped. the chips become shallow, and the saw ceases to go deeper into the tree.

    The earlier blunted teeth are sharpened, the less material needs to be removed during sharpening, as a result. the chain life is longer. Determining the moment when sharpening is already required is quite simple. An important feature is the feed force. A properly sharpened chain retracts into the cut even with a slight pressure. If on the contrary, a chainsaw is forced to saw with an increased feed force, then the teeth become dull. A dull chain can also be recognized if, instead of a large thick chip, only small chips fly out of the cut.

    In this situation, the chainsaw should be sharpened urgently. Do not saw with a blunt or defective saw chain. the result is a strong tension in the body, a large cyclic load, poor cutting results. In addition, this means a decrease in productivity, high fuel consumption and increased wear on all nodes of the chainsaw.

    Chain Tooth Parameters

    To achieve optimal cutting properties, certain angles are attached to the tooth blades. The tooth back that slopes at an angle back forms the posterior angle of the upper blade. This angle is needed for cutting the upper blade into the wood.

    The tapering back of the tooth blade forms the posterior angle of the end blade. This angle is needed for side cutting chips.

    The edge of the end blade forms a rake angle with the sliding surface of the cutting link. The front angles of different types of chains vary from 60 to 85 °.

    The rear corner of the upper blade characterizes the tilt of the upper blade back.

    This angle is measured relative to the sliding plane of the cutting link and, depending on the type of saw chain, has a value from 50 ° to 60 °. The upper blade is the main blade, and the rear corner of the upper blade. this is the most important angle. The rear corner of the upper blade is difficult to measure, its correct value is formed subject to other prescribed values.

    The grinding angle or the angle in the plan is obtained by measuring from the upper cutting edge at a right angle to the guide rail.

    The angle of sharpening can be changed, depending on the application. The main rule: the greater the angle of sharpening, the higher the cutting performance when cutting unfrozen soft wood. Reducing the angle of sharpening when cutting frozen and / or solid wood contributes to a smoother stroke of the saw and a reduction in vibration. However, sharpening angles of more than 35 ° and less than 25 ° should be avoided (chains are excluded for longitudinal cutting, in which this angle is 10 °).

    The rake angle, the angle of sharpening and the angle of the upper blade change when sharpening. These angles have a decisive influence on the cutting ability of the chain. Be sure to follow the prescribed values.

    Video: How to Sharpen Stihl Chainsaw Files Properly


    On each cutting link in front of the tooth blade there is a depth limiter. The height difference between the top edge of the depth gauge and the front edge of the tooth back is defined as the distance of the depth gauge.

    The depth of penetration of the upper blade into the wood (chip thickness) and, thereby, productivity, depend on the distance of the depth gauge. The depth gauge distance is set depending on the chain pitch and type of execution. Normally, it should be 0.5-0.8 mm, usually 0.6 mm. High values ​​will lead to an increased tendency of the chainsaw to recoil, too much grip and vibration of the chain. Low values ​​result in poor performance. Since the distance of the depth gauge with each sharpening of the saw is reduced due to the reduction of the upper edge of the tooth, the depth gauge also needs to be filed periodically. after 5-10 sharpening the chain.

    General rules for sharpening chainsaw chains

    Chain sharpeners

    On the holder with a round file there are mowing lines that allow it to be correctly positioned relative to the chain. The holder is mounted on the sharpened tooth in accordance with the orientation lines. In this case, the plate itself rests on the upper edge of the tooth and the depth gauge, and the file is located under the cutting edge.

    Using a toolholder ensures that the file adheres to the tooth at the correct height. There are various tool holders for different steps of the saw chain. The right choice of tool holder in combination with the correct file diameter ensures that the file protrudes 1/5 of its diameter above the tooth back. Use only special files for sharpening chains.

    Before sharpening the chain of the chainsaw, it is advisable to fix the tire. When sharpening, it is necessary, while maintaining the position of the holder and pressing the file against the edge to be sharpened, to make several (2-3) turning movements away from you. No need to try to press the file too hard, the movements should be smooth and measured. Turn the file regularly to avoid one-sided wear. All other teeth are ground in the same way. It is more convenient to first sharpen the teeth of one direction, then change position and do the same with the teeth of another direction.

    When sharpening all teeth, make the same number of movements with a file at the same pressure. This will result in the same tooth length. All cutting teeth must be the same length. Different tooth lengths cause uneven chain travel and cracking in it. If the length of the teeth is not the same, all cutting teeth should be filed to the length of the shortest tooth.

    After several sharpening of the cutting teeth, the depth gauge grinds. To do this, a template is superimposed on it so that the limiter falls into the slot, and the tip protruding from the slot is ground with a flat file.

    The principle of using a different set for sharpening chains of chainsaws does not differ from the first, although its design has differences.

    A round file is also used for sharpening a cutting tooth, and for sharpening a depth gauge. flat. A special template provides sharpening parameters for both cutting teeth and limiters. In the first case, it is superimposed on the chain so that it falls into its slots. A file overlaid on the template and brought under the cutting edge rests on the guide rollers. The direction of file movement should be parallel to the side edges of the template.

    When grinding the limiter, the template is superimposed so that the limiter falls into the slot next to which SOFT (for soft wood) or HARD (for hard wood) is written. As in the case of the first fixture, grinding is performed by smooth smooth movements of the flat file away from you.

    Chainsaw sharpening machines

    Stihl produces two modifications of hand-held machines. stationary FG 2 and mobile FG 1 mounted directly on the bus. There are analogues of lesser-known companies, comparable in price with the simpler devices described above.

    The working part of these devices is structurally reminiscent of a beam saw, into which a round long file is inserted instead of a saw blade. FG 1 and FG 2 not only sharpen the chains, but also straighten them, adjusting the length of the upper edge of all the teeth to the same size. on the smallest tooth, which is taken as the control. A rather complicated configuration mechanism allows you to set all the necessary parameters. Sharpening is performed in 2-3 movements, after which they proceed to the next tooth, saving for it all the settings that were made for the control tooth. This ensures the same grinding parameters for all teeth. When grinding the limiter, the round file changes to a flat one.

    Simple and easy to use electric grinding machine for chainsaw chains. It has a tuning system that allows you to set the chain at the right angle and bring the disc exactly to the edge to be sharpened. There are machines that automatically clamp the vise when lowering the disc onto the chain.

    How to Properly Adjust a Stihl 55 Trimmer Carburetor

    On trimmers, in addition to electric motors, gasoline internal combustion engines are installed. This mechanism requires special attention, because if configured incorrectly, it will either refuse to work or will work intermittently and loss of power. Basically, adjusting the engine is to adjust the fuel supply, and this is done using the trimmer carburetor.

    How is the gas trimmer carburetor arranged and working

    All varieties of carburetors produced by manufacturers of gas trimmers are almost impossible to cover. But, since the design of this module, as well as its operating principle, is largely similar between different models, a generalized description of the processes occurring in the carburetor can be made. This information will allow the user to understand the principles of operation of the device, eliminate the problems that have arisen and operate it correctly.

    The basis of the carburetor trimmer is solid aluminum housing. Below is a diagram of this unit.

    How to Properly Adjust a Stihl 55 Trimmer Carburetor

    At the bottom of it is a diffuser, which is also called venturi nozzle (18). Air is sucked in by the motor through this nozzle.

    The smaller this hole, the faster the air flows, and the higher the level of its rarefaction in the zone with the smallest diameter.

    At the top of the diffuser are fuel channels (11.12). Through these channels, the flow of air draws in gasoline. The fuel pump itself, the jets and the system used to control the flow of the fuel-air mixture can be built-in or installed externally.

    Throttle (9) adjusts the amount of air drawn into the carburetor. Its amount affects the power that the engine develops. The damper (7) is used for cold start. It must be closed if you intend to start the unit. After the engine has started, it needs to be opened, otherwise, the motor will immediately stall.

    Pulse channel (1) connects the impulse chamber of the pump to the crankcase, namely, to its internal volume. The piston located in the cylinder, making a reciprocating motion, successively changes the pressure in the crankcase (vacuum or pressure increase). Pressure drops make the membrane move (4). Therefore, the operation of the pump is synchronized with the operation of the engine.

    It is precisely with the participation of gasoline leaking from the tank membranes (4). Gasoline enters the carburetor through the fitting (2). Further, its path lies through the inlet valve (3), the exhaust valve (5), through the strainer (6), the fuel channel (10), passes by the needle (14) and fills the chamber (16) having a control membrane (18).

    The valve (14) by means of a lever (17) is connected to the membrane (18). The cavity, which is located below the membrane, is connected to the atmospheric air through the hole (19).

    The device operates as follows.

    1. A vacuum is created in the diffuser during the suction stroke. This fact causes air leaks. The position of the throttle (9) determines the amount of air entering the carburetor chamber, as well as engine power and the number of revolutions.
    2. At this time, fuel from the chamber (16) is sucked through the jets (11,12), after which it is mixed with the flowing air. Gasoline, mixed with air, begins to spray. Thus created air fuel mixture.
    3. The finished mixture enters the cylinder, where it is compressed by a rising piston and ignites at its correct point from the spark generated by the spark plugs.
    4. Since the volume under the control membrane (18) is connected with atmospheric air through the channel (19), the membrane goes up, opening the valve (14) by means of the lever (17). After opening the valve (14), a new portion of fuel enters the chamber (16).
    5. After the chamber (16) is full, the membrane (18) returns to its original position, and the valve (14) closes.

    Further, when the motor is running, all of the above processes are repeated. To adjust the amount of fuel entering the diffuser through the nozzles, a screw (13) is used. A screw (15) is also used to adjust the idle speed. When the regulators are twisted, the fuel mixture is enriched, and when twisted, the mixture becomes lean. Also, in some models of carburetors, you can adjust the engine idle quantity regulator. It is usually located outside and, when twisted, rests on a lever fixed to the axis of the throttle.

    Thus, using 3 adjusting screws, it is possible to achieve maximum engine performance, as well as to configure its smooth operation at any ambient temperature, and even in mountainous areas.

    Common carburetor malfunctions

    Damage to the trimmer carburetor occurs due to the use of poor quality gasoline, a damaged air filter and the accumulation of dirt in the chamber of this unit. Most often, it is quite possible to repair a carburetor with your own hands. The following are typical malfunctions of the carburetor lawn mowers.

    Fuel pump problems

    A common malfunction that “chases” the fuel pump is pump membrane deformation. For this reason, it does not fit properly and the pump channels are not sealed.

    The causes of membrane deformation can be as follows:

    • long operation of the trimmer;
    • use of unsuitable fuel;
    • gas entering the pulse channel.

    As a result, damage to the membrane reduces the performance of the pump, and as a result:

    • there is a depletion of the combustible mixture;
    • difficulty starting the engine;
    • there are interruptions in the motor;
    • the piston is damaged.

    Also, the aforementioned consequences for the engine may cause clogging of the pump cavity with impulse side. In this case, dirt enters the membrane through the pulse channel.

    To eliminate clogging, you will have to disassemble the carburetor and clean the membrane.

    Strainer clogging

    The strainer may become contaminated when contaminated fuel enters through a fuel hose or defective suction head. In the photo below you can see what a clean filter looks like and dirty (the parts are separated by a dash).

    A thorough cleaning and rinsing of the strainer will be required to resolve the malfunction. Also recommended blow with compressed air all openings in the trimmer carburetor body.

    Adjustment lever defective

    This failure occurs when the contact surface of the lever wears out.

    The contact surface is erased due to the presence in gasoline abrasive particles or due to strong vibration of the motor during operation. This defect of the adjusting lever causes problems with the inlet, as well as improper engine idling.

    Inlet needle wear

    The intake needle fails, usually due to the presence of abrasive particles in the fuel fluid.

    • the tightness of the seat of the inlet needle is violated;
    • leakage of the combustible mixture appears;
    • there are malfunctions in the engine, associated with the re-enrichment of the fuel mixture.

    Also, the inlet needle can simply jam.

    Jamming the inlet needle may cause the presence of dirt in the fuel, or a long simple machine without work.

    Clogged control cavity

    If dirt accumulates in the adjustment cavity, the inlet needle cannot close the hole tightly and a lot of fuel is poured into the chamber.

    It causes re-enrichment of fuel, and the engine starts to malfunction. It is necessary to disassemble the carburetor and clean the cavity of the adjusting membrane.

    Adjustment membrane deformation

    The membrane can undergo deformation during prolonged operation of the unit and when using aggressive fuel.

    The impossibility of normal adjustment due to a defect leads to:

    • piston damage;
    • difficulty starting;
    • depletion of fuel;
    • engine malfunction.

    Inlet Adjustment Lever Problem

    This problem may occur if the adjusting lever is not installed correctly, or bend it before installation. As a result, the contact surface takes the wrong position, which disrupts the additional fuel supply.

    Damper wear

    Throttle and air dampers mostly wear out due to the presence of abrasive particles in the air. Defective flaps look like they were sandblasted.

    Video: How to Properly Adjust a Stihl 55 Trimmer Carburetor


    As a result of wear of the dampers, engine performance decreases, malfunctions appear in its operation, piston rings, piston and cylinder cover wear out.

    Throttle and air damper shaft wear

    The air and throttle shaft may wear out for the following reasons:

    • insufficient and improper maintenance of the air filter;
    • the air filter is damaged;
    • The air filter is not suitable for this unit.

    Due to hit poorly cleaned air, The shaft wears out and may break. Broken parts of the shaft can enter the combustion chamber or crankcase and cause serious damage to the entire piston system.

    To eliminate problems with air purification, it is necessary to replace the defective filter or rinse the existing one (serviceable). The filter must be washed in soapy water and dried.

    When to adjust

    Carburetor adjustment is necessary in the following cases:

    • the new engine was tested (4-5 liters of fuel mixture were used);
    • fuel composition has changed (brand of oil and gasoline);
    • the weather has changed (it has become hot, cold);
    • rarefied air (applies to mountainous areas);
    • after prolonged storage;
    • increased engine load (after changing tools, etc.);
    • due to vibration, the adjustment screws spontaneously unscrew;
    • increased fuel consumption, carburetor overfills fuel;
    • carbon deposits quickly appear on the spark plug electrodes (while the fuel mixture is prepared correctly);
    • the engine starts and immediately stalls or picks up poorly;
    • no gas enters the cylinder;
    • a large amount of exhaust gas.

    How to adjust

    Before setting up the trimmer carburetor, do the following:

    • flush the engine;
    • replace or clean the spark plug;
    • change to a new one or clean the air filter (it is recommended to wash it in warm, soapy water, squeeze it out and let it dry well).

    Also necessary set cord suitable diameter in the trimmer coil or install knives. this is done so that during the tuning process the engine has at least some kind of load. After installing the cutting tool and starting the gasoline engine, let it warm up for 10 minutes.

    If at idle You noticed that the cutting tool rotates, therefore, it is necessary to reduce the engine speed. This is done using the lower idle control, often marked with the letter “T”. The figure below shows the placement of the knobs on the Husqvarna trimmer.

    But, for example, on a Stihl trimmer, this screw may be labeled “LA”.

    So, turn the idle speed control to the left, until the trimmer head stops completely.

    To adjust the carburetor, 3 regulators (screws) are used.

    1. Right knob L adjusts the level of enrichment of the combustible mixture at low speeds. It needs to be regulated first. Get maximum idle speed. This is done using the L knob, turning it left and right. After finding the point of maximum revolutions, return the regulator half a turn to the left (counterclockwise).
    2. Lower T knob (LA) used to set idle speed. By turning it to the left, the engine speed will begin to decrease, and when you turn the regulator to the right, the speed will increase.
    3. Left knob H responsible for the enrichment of the combustible mixture at high speeds. The enrichment setting completes the carburetor adjustment. Also, using this controller, you can adjust the maximum speed, fuel consumption and engine power.

    Important! If the engine is allowed to run at full speed for more than 10 seconds, then it may fail.

    To eliminate this trouble, adjustment will be required. With the engine running, give full throttle, then turn the “H” knob to the right until the reduction in speed begins. After that, the “H” knob must be slowly turned to the left until you hear the engine running unevenly. Then turn the “H” knob to the right until the engine runs smoothly.

    After carrying out the above steps, the carburetor adjustment can be considered completed. After proper adjustment, the engine must confidently gain revolutions, slightly quadruple at maximum revolutions, and when idling, the cutting tool should not rotate. This manual is suitable for adjusting carburetors on the Huter, Patriot, and others.

    Also exist screwless carburetors, responsible for the enrichment of the combustible mixture at low speeds. That is, they have only 2 adjusting screws: the idle speed regulator and the fuel mixture quality regulator at high speeds. You can learn how to tune this type of carburetor from this video.

    Do-it-yourself carburetor adjustment for lawn mowing

    lawn mowers, like all gasoline powered tools for the garden, are not difficult to maintain. It is possible and necessary to repair, configure yourself. For example, adjusting the carburetor lawn mowers do it yourself. a matter of five minutes.

    Lawn mowing carburetor is a unit in the power system. In it, like any carburetors, there is a process of mixing air and fuel (gasoline) for further supply to the engine cylinders.

    In this process, the main thing is the correct proportion of fuel and air, for which they regulate the carburetor.

    The main problems and malfunctions of the carburetor.

    Strainer There are only two problems with this element:

    In order to find out the cause of the breakdown, the fuel filter cover is unscrewed to remove the strainer. If dirt has simply accumulated on it, washing with gasoline or blowing will help.

    With visible damage to the strainer, it is imperative to install a new one. There may also be damage on the fuel supply pipe (during repair, check this element).

    The carburetor starter in most cases does not function due to blockages. Use rinse with acetone or the same gasoline.

    Related posts

    Blowing off carburetor parts with a blockage of compressed air is an acceptable and convenient repair practice.

    The throttle body, the bundles of carburetor parts, the intake or exhaust pipe. all of these parts are subject to depressurization. You can probably check it in a primitive way. smear the problem area with soap suds.

    The device of the carburetor lawn mowers

    The basis of the carburetor of the lawn mowers is an aluminum case. It contains a diffuser (a hole with internal contours). Air is blown through this hole. The oxygen (air) flow rate depends on the cross-section (passage opening) of the diffuser.

    The diffuser is equipped with fuel channels. Of these, fuel is drawn in using an air stream.

    Outside the carburetor is installed:

    • fuel pump;
    • jet system;
    • fuel / air mixture control system;

    The principle of the carburetor lawn mowers

    The throttle valve determines the amount of air for supply, and engine power directly depends on this.

    Carburetor adjustment for the Stihl FS 55

    Adjustment carburetor lawn mowing Stihl FS 55 Parts store Sadservice sadservice.com.ua.

    Fuel is sucked into the carburetor system by a pump (its membrane). Then it passes through the fitting in the carburetor. Further, the fluid moves through the inlet and outlet valves of the pump. Filtered by mesh. The needle valve moves into the membrane chamber.

    Phased operation of the device:

    1. Air supply to the tube with an air baffle (damper). The partition controls the intensity of the air flow.
    2. The fuel supply system must be narrowed by a diffuser to increase the flow rate.
    3. Gasoline through the float chamber and nozzle tube with narrowing. A camera with a float adjusts the temporary volume of gasoline. In the float chamber, the pressure level is neutral, and in the tube with narrowing is already low. Due to the pressure drop, fuel enters through the nozzle.
    4. The acceleration of the air flow contributes to the transfer of fuel (gasoline) and its atomization. As a result, an air-fuel mixture of the necessary proportion or density is formed.
    5. The air-fuel mixture enters the engine cylinder through the fuel pipe.

    The level of air density in the system depends on the area of ​​the open air damper. The wider the flap is open, the greater the fuel consumption and power.

    Simply put, adjusting the carburetor on the lawn mower is creating the optimal fuel mixture due to the correct air supply.

    how adjust lawn mowing carburetor

    Before adjustment, carefully clean the filters according to the maintenance in the instructions.

    Do-it-yourself carburetor adjustment for lawn mowing

    lawn mowers, like all gasoline powered tools for the garden, are not difficult to maintain. How to properly adjust the carburetor on a chainsaw. Stihl fs 55 carburetor adjustment of the carburetor trimmer Stihl fs 55 in how to adjust. It is possible and necessary to repair, configure without the help of others. For example, adjusting the carburetor for lawn mowing with your own hands is a matter of 5 minutes.

    Lawn mowing carburetor is a unit in the power system. In it, like all carburetors, there is a process of mixing air and fuel (gasoline) for the upcoming supply to the engine cylinders.

    The main thing in this process is the correct proportion of fuel and air, which is why the carburetor is regulated.

    The main problems and malfunctions of the carburetor.

    Strainer How to adjust the chainsaw How to properly adjust the carburetor on the husqvarna chainsaw. There are only two obstacles with this element:

    In order to find out the cause of the breakdown, the fuel filter cover is unscrewed to remove the strainer. If it just accumulated dirt, then washing with gasoline or blowing will help.

    With visible damage to the strainer, it is imperative to install a new one. There may also be damage on the fuel supply pipe (during repair, check this element).

    The carburetor starting device almost always does not work due to blockages. Use acetone or the same gasoline for flushing.

    Blowing off carburetor parts with a blockage of compressed air is an acceptable and comfortable repair practice.

    The throttle body, the bundles of carburetor parts, the intake or exhaust pipe. all of these parts are subject to depressurization. We adjust the trimmer carburetor Stihl FS 55 in the video in order to adjust the idle speed. How to adjust the carburetor on a scooter in your own. Probably you can check with a simple method. smear the problem area with soap suds.

    The device of the carburetor lawn mowers

    Read:

    Base carburetor lawn mowers. duralumin housing. It contains a diffuser (a hole with internal contours). Air is blown through this hole. The oxygen (air) flow rate depends on the cross-section (passage opening) of the diffuser.

    The diffuser is equipped with fuel channels. Fuel is drawn from them by an air stream.

    Outside the carburetor is installed:

    • fuel pump;
    • jet system;
    • system for adjusting the consistency of fuel with air;

    The principle of the carburetor lawn mowers

    The throttle valve determines the amount of air to be supplied, and the motor power directly depends on this.

    STIHL FS 55. carburetor adjustment (idle)

    Adjustment trimmer carburetor Stihl FS 55 in the video we execute with the aim of adjust idle speed.

    Carburetor adjustment for the Stihl FS 55

    Adjustment carburetor lawn mowing Stihl fs 55 Parts store Sadservice sadservice.com.ua.

    Fuel is sucked into the carburetor system by a pump (its membrane). How to adjust the carburetor you were told correctly. Adjusting the carburetor trimmer Stihl fs 38 Then it passes through the fitting in the carburetor. How to adjust the carburetor gasoline lawn mowers. How to adjust the carburetor to the carburetor from the lawn mowers is a node in the power system. Further, the fluid moves through the inlet and outlet valves of the pump. Filtered by mesh. The needle valve moves into the membrane chamber.

    Phased operation of the device:

    1. Air supply to the tube with an air baffle (damper). The partition controls the intensity of the air flow.
    2. The fuel supply system is certainly narrowed by a mixer to speed up the flow.
    3. Gasoline through the float chamber and nozzle tube with narrowing. A camera with a float adjusts the temporary volume of gasoline. In the float chamber, the pressure level is neutral, and in the tube with narrowing is already small. Due to the pressure drop, fuel leaks through the nozzle.
    4. The acceleration of the air flow contributes to the transfer of fuel (gasoline) and its atomization. Ultimately, an air-fuel mixture of the desired proportion or density appears.
    5. The air-fuel mixture seeps into the engine cylinder through the fuel pipe.

    The level of air density in the system depends on the area of ​​the open air damper. The wider the flap is open, the greater the fuel consumption and power.

    Simply put, adjusting the carburetor on the lawn mower is creating a good fuel consistency due to the correct air supply.

    how adjust lawn mowing carburetor

    Before adjusting, you must carefully clean the filters according to the maintenance in the annotation.

    Read:

    Right (L). adjustment of fuel consistency for low revs.

    It is necessary to find the highest idle speed. Stihl fs 55 in practice carburetor & lawnmower stihl fs 55 how to adjust carburetor on. To do this, slowly unscrew the screw (L) to the right and to the left.

    To adjust, turn the screw a quarter turn without fail counterclockwise.

    Bottom (T). is responsible for adjusting the engine at idle.

    • clockwise. increase;
    • counter-clockwise. decrease.

    For the correct adjustment of idling, it is typical:

    • steady work of the cool motor;
    • not overestimated speed of a hot engine;
    • for the trimmer head a large reserve of revolutions;
    • stable operation of the motor when changing position (sharp rise or lowering of the knife).

    Left (N). adjustment of consistency at high speeds. (The screw is configured last).

    The general adjustment of the highest revolutions, engine power, temperature and gas mileage depends on the left screw (H).

    Setting the carburetor lawn mowers with the last screw is as follows:

    1. Open the throttle to full, while giving out full throttle. How to adjust the carburetor on the vaz 2109? The scheme of vases 2109. Turn the screw clockwise until the momentum falls (in this case, they are oriented by ear).
    2. Turn the screw as slowly as possible counterclockwise until the motor runs unevenly.
    3. Then turn back completely a little, just hearing a measured, steady work.
    4. For a more pleasant implementation of abilities, it is more convenient to discern the work of an experienced user:

    It is curious that, based on the beliefs of the creator of the video, the setting (its correctness) is determined by the color of the candle, and not just by the speed and stability of the motor.

    Right carb setting do it yourself in this case, the combustion of the fuel consistency without residue, the color of the candle should be light brown.

    How to Properly Fill a Fishing Line With a Stihl Trimmer

    How to Properly Fill a Fishing Line With a Stihl Trimmer

    Guaranteed production of a factory trimmer refill will inevitably require replacing the fishing line. Having a very rough idea of ​​how to fill the fishing line into the reel of the trimmer yourself, beginners are reluctant to take up this matter. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will facilitate this process as much as possible.

    Preliminary preparation

    First of all, for winding fishing line it is required to remove the reel (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of product itself:

    • Small electric trimmers with a working arrangement of the engine and the coil in the lower part, as a rule, have side keys on both sides of the bobbin. By pressing them simultaneously, the upper part of the reel, together with the internal contents for winding the fishing line, is disconnected, while the lower one remains on the trimmer. It is advisable to disassemble the bobbin on an even smooth place so that the spring included in the design does not pop out and is not lost;
    • electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have coils with a special wing: in such designs, you should hold the spool in one position with one hand and rotate the locking reel on the wing nut with the other counterclockwise. After disconnecting the nut, the entire reel is removed.
    • electric and petrol trimmers with the possibility of installing the knife on a straight bar (for example, Stihl trimmers) have a hole under the bobbin. For the motion of the rod to be stationary, a screwdriver or other suitable object is inserted into this hole and with a slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body scrolls clockwise (with the left thread) and is removed from the trimmer.

    For the second and third cases, the coils, depending on the design, are disassembled in various ways. In bobbins with a lamb, a lamb is twisted, in coils with latches, latches-clamps are pressed and one part of the coil is released from the other. If the halves of the spool are threaded, it is enough to turn them by hand in opposite directions until completely unscrewed.

    Video: How to Properly Fill a Fishing Line With a Stihl Trimmer


    We carry out winding fishing line

    Slowly completed disassembling the spool of the spool without losing its spare parts allows you to go to the main task. winding the fishing line into the reel. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

    Coil with one working antenna

    The simplest option and a simple sequence of actions:

    1. The dimensions of the bobbin and the length of the original factory winding determine the recommended fishing line length for winding. 2. 5 m.
    2. One end of the fishing line is inserted into the fixing technological hole located inside the spool.
    3. The fishing line is wound on the drum in the reverse direction of rotation of the spool in the trimmer product direction. as a rule, on the inner side of the bobbin an arrow indicates which side the winding is carried out.
    4. A small area of ​​fishing line is left free to bring it out. it is fixed in a specialized groove on the inside of the reel, designed to hold the winding when assembling the spool in working condition.
    5. The left end of the line is passed through the hole on the outside of the bobbin.
    6. The bobbin halves are assembled and put on the trimmer bar.

    Coil with two working antennae

    In this type of spools, you should determine the number of grooves for winding fishing line lying on the inside of the reel:

    • one groove. both antennae are wound together along one groove;
    • two grooves. each antennae is wound on an individual groove.

    In both cases, a 2-3-meter-long fishing line is taken. In single-groove reels, the fishing line is pulled into the through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the side of the bar. the correct direction of winding is usually indicated inside the arrow. In the presence of fixing grooves, the ends of the fishing line are threaded into them or held by the fingers of their free hands, threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the bar of the trimmer.

    The difference between winding fishing line in two-groove reels is that initially a piece of fishing line 2-5 m long is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each in its own groove, the fixation of the antennae and the reel assembly is similar to the one-groove variant discussed above.

    The first implementation of this procedure may seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

    The video below will clearly show how to put the fishing line into the coil of the trimmer and wrap it correctly. this operation is not complicated and with some patience will surely succeed:

    Automatic reeling of fishing line

    There is a variety of coils in which the automatic mechanism coils on its own. from the user it is enough just to properly fill the line. The fishing line is passed through the hole on the inside of the case, its antennae without winding is passed through the hole on the external case, the bobbin is assembled, and when the winding button is rotated, the line inside is wound up independently. In such a spool, it is impossible to make the winding incorrectly: the mechanism itself will determine the correct direction, since it can only turn in one direction.

    1 2 3