How to start a motor -cultivator without a starter. How to start motoblocks of popular brands?

Correct launch of a walk.behind tractor: First, after winter and without a starter

Operation of garden and searry technology begins with its launch. The same.based tractor is a design that provides a complex fuel system and engine. At this stage, any error can cause a breakdown breakdown, a decrease in its work and the life of operation. Depending on the model of the device, its type of engine and the season, the launch includes its characteristics. Knowledge of basic rules and recommendations will make the start of the walk.behind tractor high.quality, and do not damage the unit.

In order to put the equipment into operation, several rules should be fulfilled:

• Check the amount of oil. Even if when buying it was assured that everything is flooded, you must definitely make sure that the level of technical fluid in the system is sufficient. Some models of motoblocks are equipped with sensors that respond to a lack of oil and simply do not allow to start a motor. But such an option is not characteristic of everyone, there is a technique that can be launched, but this threatens with breakdowns.
• Refun with fuel. It is necessary to take into account the recommendations to a certain model. Gasoline for some will need to dilute. Proportions are indicated in the instructions for the technique. If the one.axle tractor is on a diesel engine, then you need to take into account its type according to the time of the year. Summer DT pouring in winter can provoke a driving fuel hoses, which will operate the machine impossible and cause the need to repair.
• Check and configure the compounds. Clutch, steering, gas. they need to be adjusted so accurately as to ensure the smoothness of switching.

Important! New equipment is always supplied with the instructions for the manufacturer. It usually indicates the main recommendations for the use and maintenance of the machine. Therefore, you should first familiarize yourself with the instructions for a specific model and only then proceed to the direct launch of the walk.behind tract.

Description

PROFI motor blocks are SHENLI products. A series of motoblocks is an independent technical branch, in the model range of which many units of motorcycle equipment are represented. all motoblocks of the pros have different power, have a certain set of technical characteristics. Profi 1800

Profi. a separate direction of motoblocks, they belong to the class of heavy motor vehicles, but are not intended for professional use. Their purpose is domestic. Can be used for auxiliary work on the site, for example, for the transportation of a crop, collecting garbage, cleaning territories from snow.

Profi 1900

The PROFI brand appeared after the STENLI motornote enters the SGN market, around the late 90s of the 20th century due to the demand for universal medium-weight motoblocks, which made it possible to make such a technique more accessible for a wide range of consumers.

Frequent causes of ignition system breakdown

Often, the Mole motor cultivator cannot be made due to a number of other malfunctions, all of them are associated with the ignition system of the unit. The breakdowns include:

• Lack of spark. this indicates a malfunction of the candle and the need for its urgent replacement. Often the cause of this malfunction is a violation of the clearance between the ignition coil and the magnetic wire;
• Another often breakdown is a violation of the connection of a gasoline hose. It will be necessary to carefully examine this element and check its fastening with other nodes of the cultivator;
• The next malfunction is to contact the wire of the magneto and the plate of the fly wheel. You will need to achieve a gap between these elements.

Experts strongly recommend not wasting time and effort to restore the old candle. It is best to immediately go to the automobile market or to the store for the sale of equipment and buy a new part.

Features of independent cultivator repair

If you find out why your mole motor cultivator does not start, then it’s time to start repairing. Since most often the essence of the problem lies in violation of the distance between the magnetic shoe and the stator, it is necessary to consider the features of the repair of this breakdown.

The algorithm for the repair work of the Mole motor cultivator looks as follows:

• To get started, remove the fan housing;
• Do not completely release several fasteners;
• Install the probe plate in the gap between the shoe of the flywheel and the stator, screw the fasteners;
• Twist the flywheel and follow the gap.

Having performed these operations, you need to check the presence of a spark on the mass of the case. To do this, scroll the crankshaft through the starter. If there is no spark, then the starter will need to be replaced immediately.

1 review

With the correct and rational use of a mole motor block, it will serve you for more than one year. Remember that it is better to prevent ignition breakdown than then to repair.

If you are looking for an optimal value for price and quality, we recommend that you pay attention to the domestic one.based mole tractor, which has been released from 83 years old. The same.based tractor is produced today in the Omsk Machine.Building Plant. In recent years, high.quality technical characteristics allow him to successfully compete with many foreign units. But there are also moments when you do not know why the one.legged tractor of the mole does not start or it starts poorly or there is no spark in it. It may be necessary to repair the starter, and maybe the ignition may fail faultly. In general, with this question and reasons you should carefully figure it out.

The rules for launching the motor in the absence of a starter

Engine operation is a complex technical process for which several nodes in the machine are responsible at once. One of the devices providing conditions for launch is a starter. This mechanism leads the motor into a direct action and in importance it is not inferior to the ignition or adhesion system.

Important! Starters are one of the most vulnerable details in the system. Often they break, including among the season, when there is a lot of work. The engine can be started without it, which saves time on urgent repairs.

The stages of launching the motor in the absence of the starter include:

• Dismantling of faulty spare parts.
• Fixing a strong rope in the hole on the round iron component, which is located at the site of installation of the starter.
• The cable needs to be wrapped around this corolla several times (about 4-5 revolutions), leaving an end to about 40 cm.
• The piston is brought up, the decompressor turns off and the rope twitches sharply.

Despite the fact that the launch of a motor block is possible without a starter, it should not constantly operate in this mode. These recommendations are given for emergency cases when equipment is required in working condition. But you should also not have time to repair. you need to quickly order a new starter. Details for the Unoa tractor in the assortment are presented on the website of the company “Belagro”, where you can choose them for different models of special equipment.

How to launch equipment after winter

Motoblocks after prolonged downtime start quite poorly. At the first launch in the new season, it is immediately recommended to change the fuel (gasoline or DT) in the system (“dry” can not be stored, this can provoke drying out and damage to the hoses). Technical fluids should be equal to the external environment in temperature.

Immediately a single tractor may not start. This is a normal phenomenon: the details in the system should warm up well. You also need to let the car work at idle after starting the engine. It is also worth considering that it is impossible to immediately begin the intensive operation of the motor block, the fuel is thickening after the winter, which is why the load on the nodes of the equipment increases.

If the motor does not start stubbornly, you should resort to the following actions:

It’s important to know! The conditions of storage have a great influence on performance. If the one.axine tractor was stored in cheese and cold room, this can provoke serious problems.

How to get a motorcycle without a starter

Initially, you need to understand the reasons for the fault failure. Both external climatic factors and internal mechanical factors can influence. Among the most common problems can be distinguished:

• weak work of a retracting relay;
• malfunction of the starter relay itself;
• combustion of the winding in the engine;
• The wear of the equipment, namely the teeth of the six.ladies: it operates and spins in the mechanism, but does not end up for special teeth during operation.

For all these reasons, problems may arise with the usual launch of the engine. It is necessary to prepare a plan of action in advance, which will help to cope with the problem yourself. First of all, it is necessary to carefully dismantle the starter in order to access the special nuts of the rating of the ratchet. This will make it possible to get to the right part as close as possible.

Then you need to insert the prepared bolt into the side head of the equipment. Its location must be a thread forward, the hat always remains inside. After all the manipulations carried out, the edge of the bolt must be clamped in the cartridge of an electric screwdriver or drill. Gently put the head on the nut of the ratchet and start the drill. Together with this, the process of launching motorcycles will begin. As soon as the device starts to work, it is necessary to tightly pull the drill over yourself to pull out the head.

After that, the launch process can be considered completed. However, it is worthwhile to take a very attentive to the choice of equipment. Not only convenience, but also the efficiency of starting will directly depend on this. If you use the drill, you will definitely need access to the outlet. This opportunity can not be found in all summer cottages and in ordinary houses. That is why such a tool will not always be practical.

But the battery electrical screwdriver will cope with the task in any place, even in Dali from the network and civilization. But before use it is necessary to check the level of charge so as not to fall into an unpleasant situation.

Therefore, when choosing a tool, you need to be guided not only by the power of the equipment, but also the direct type of power: battery or from the network.

Thus, the process of launching motorcycles without a starter does not represent anything complicated. It is easy to find a drill or an electric screwdriver and a couple of fasteners at hand. The starter may fail for various reasons, over time it will need to replace it.

But for the first time, you can limit yourself to universal ways of starting. The main thing is to carry out all the actions in order and carry out safety rules. Then the equipment can be used as intended at any required moment.

A trimmer does not start for the grass for cold reasons

To begin with, we will analyze the situation when it is impossible to start the engine of the lawn mower to the cold. What does this mean? Surely Kosari came across a situation where a trimmer for grass starts on hot just perfectly, but you just have to make a short break, as the problem arises. This problem with the start of the engine after it cools. What could be the reason? Of course, no one excluded all the above factors, but if the situation is constantly found, then there is no need to check them. If a hot lawn mower starts well, and problems arise on the cold, then you should look for the reasons inside the CPH (cylinder-piston group).

To identify a malfunction, you will need to use a compressometer. We screw the compressometer into the hole instead of a candle, and after that we drive the starter handle. Measure the pressure inside the cylinder. compression. The amount of compression should be at the level of about 8-12 atmospheres. After the tool has warmed up (it is enough to work for 15-20 minutes), you should repeat the verification procedure. If the compression on the hot engine is below 8 atmospheres, then the CPH fault is appropriate. This means that the rings, the piston and the walls of the cylinder are worn out.

You can fix the situation by replacing CPG

When replacing it, it is important to take into account such a recommendation as abundant smearing of parts with motor oil inside the cylinder. This is necessary so that in the first minutes of starting a new cylinder with the piston, no formation of

With a decrease in engine compression, fuel consumption increases, and the productivity of the tool falls. You can work with such a tool, however, with each subsequent hour of work, wear increases. One day, the lawn mower will not be completely launched even with warming up.

It is interesting! You can warm up the engine of the lawn mower with low compression by pulling the starter handle. When warming up, the metal is expanded, thereby the compression increases.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, it first needs to be disassembled, and then collect it. This process is not particularly complicated. You will need to work the shape of the screwdriver.

Everything should be done carefully, observing precautions, especially so that the spring does not injure the owner in case of accidental departure

Starting analysis

Disassemble the starter mechanism to install new parts instead of broken in the following sequence:

Unscrew the screw that attaches the pulley with the starter lid using a screwdriver; Remove the spring and antennae; Carefully remove the pulley (you need to turn your head or work, after putting on your glasses and gloves); Determine why the trigger worked; If the spring fell apart almost completely, it is replaced; Когда пружина выходит из крючка, она устанавливается на прежнее место, предварительно сгибая антенну (фотографии показывают процесс установки);

After the spring plate is installed inside the groove, carefully tighten it. To change the spring, the work must be performed carefully and accurately: it can accidentally explode under the influence of the force caused by its bringing into effect

Even if you carefully remove the video, the spring tape is very quickly torn off the coil and can injure the hand with sharp edges

To change the spring, the work must be performed carefully and accurately: it can accidentally explode under the influence of the force caused by its bringing into effect. Even if you carefully remove the video, the spring tape is very quickly torn off the coil and can injure the hand with sharp edges.

Immediately put in place a spring plate does not always work. This often slips, so attempts should be repeated to achieve the desired result.

Starter assembly

The assembly of the starting installation is carried out in several stages:

The coil turns over, installing it so that the bend of the spring accurately fits into the groove of the case, as in the photo below;

When making the above manipulations, it is necessary to put two goals. If this is not done, the spring will ultimately damage the plastic cup, and when it is removed, jamming will begin. This makes you feel that spring has come. To eliminate this drawback, it is necessary to install this part of a larger length or an additional goal.

When such details are not enough, you can just unscrew the screw a little, and the starter assembly will start working without fixing. But this option is temporary. It is better to repair it as soon as possible.

Spring tension

After installing the spring, tighten it. To do this, follow the following actions:

• Remove the handle from the starter cord;
• Then the rope is inserted into the groove of the coil;
• The spring is delayed by the rotation of the turn in the opposite direction clockwise (winding);
• Make the required number of revolutions specified in the operating instructions for the used trimmer model for grass, and the corresponding length of the cord used;
• At the very end, the rope is lowered into the hole provided for this, located in the starter cover;
• Place the handle in place by fixing it with a node.

Read what gasoline is pouring into the Husqvarna lawn mower

If after the repair the spring continues to fly, you can get rid of it in the following ways:

• Insert the corresponding piece of the plate into the groove at the location of the spring hook;
• Drill holes on both sides of the groove in the coil, into which you need to insert a spring hook and fix it with wire.

Replacing a torn cord

A torn cable is replaced in the following sequence:

• The old cord is removed;
• Choose a rope of a suitable size (thickness and length);
• Having passed it through a special hole located in the coil, tie a knot;
• Spring valve producing the required number of revolutions;
• Fix the pen

It is better to tighten the spring plate with Partner so that the edge of the cord does not twist inside the starter mechanism.

It is not difficult to assemble a starter on a trimmer and wound a spring, but this must be done carefully and carefully. For different models of gasoline engines, the breakdown of the starting mechanisms are the same, so they are repaired the same

However, there are some nuances associated with their constructive features.

How to launch a single tractor after downtime

Before the first launch of such a technique, especially after long, in time, downtime, it must be pre.prepared for work. First, the uniform tractor needs to roll out into the open space (on the street in the yard) and examine it for corrosion.

If there are traces of foci of corrosion on the nodes and the metal surface of the unit, they should be immediately removed, and the problem areas should be treated with special compounds (rust converters) and paint. Then, before the first launch of the equipment, it is necessary to carry out the following preparatory work:

• Remove the old one, which was flooded before the conservation of the walk.behind tractor, fuel from the tank.
• Clean the gearbox from the old lubricant.
• Clean the gear lubrication from the residues of the lubricant, rinse it, and then dry it properly.
• Pour fresh fuel, as well as transmission oil.
• Inspect the fuel tubes for their sealing and the presence of a variety of cracks. In case of acute need, for example, when strong blockages appear, they should be washed.
• Rinse and rinse filters in gasoline. Then dry them and put them back. Worn or damaged filters should be replaced.
• Carry out the diagnosis of the carburetor (dismantle it, disassemble, then blow it with compressed air and clean it from contaminants with gasoline, and then assemble it back and install on a single tractor).
• Perform a comprehensive diagnosis of drive belts for wear or large cracks. Worn or damaged belts must be changed to new.
• Complex diagnostics of the CPG of the apparatus. It needs to be disassembled and a thorough inspection for the presence on the surface of the walls of the apparatus of burrs and traces of the appearance of rust.
• Carry out a thorough inspection of the spark plug. It needs to be twisted and make sure that there is no scale on its surface, as well as a variety of deposits. Then you need to damage the machine engine. To do this, you need to stretch out the starter cable several times with sharp movements.

Then you need to make sure that the running part of the walk.behind tractor is about the serviceability of the battery, as well as the tire pressure. Before the first launch, especially after prolonged downtime, you need to make sure of the serviceability of the control systems of the walk.behind tractor.

Launching a motor unit with gasoline ICE

To run the single.axle tractor after prolonged downtime, which is equipped with a gasoline engine, you need to activate the crane through which fuel is supplied. The fuel lever should also be activated (set the start mark), and the clutch should be disconnected. After that, a manual starter is pumped (using sudden movements, pull the cable several times).

At the next stage, it is necessary to activate the ignition and sharply pull the starter cable several times. After the ICE is launched, the lever of the suction should be activated (transferred to the “work” mode). It is worth noting that after prolonged downtime, the same.based tractor may not start on the first attempt. This is due to the fact that the details and nodes of the unit need to warm up properly.

How to start a single tractor

Algorithm, how to start a one.axic tractor Neva, next. Before each use of the unit, it is necessary to check the oil level in the engine, with insufficient quantities of which you can in a short time bring as unusable the most expensive part of the cultivator. If the oil was flooded for a very long time, then it can deteriorate and also lead to engine breakdown. Some engines manufacturers, including Lon Chin, Subaru, install a quality sensor and the amount of flooded oil on their devices, so this check is not needed here. everything will be done for you electronics.

The next step is to pour fuel, the view of which should be clarified from the instructions for the operation of a particular cultivator model.

For two.stroke engines, oil and fuel are poured into 1 tank, but in a certain proportion, which is indicated on the bottle of oil.

Next, you should inspect the unit from all sides and check the fastening of the main mechanisms. These listed actions can be considered a preparatory stage when starting any cultivator without exception. Now you can go to the direct launch of the engine.

And here the differences in actions begin, and everything will depend on what kind of fuel the engine works:

• On gasoline. You should install the fuel lever to the “Start/Launch” position, open the tap and turn off the ignition. Several times you need to work with a manual starter, then turn on the ignition and pull the starter. The engine starts, while the position of the lever should be transferred to the “work” mode. Some models of cultivators are equipped with an electric starter. to start the engine, you only need to turn on the ignition and start the device.
• On a diesel engine. Because of the properties of this type of fuel, freeze in cold weather first of all, the unit should be warmed up. When using a motor.cultivator, for the first time after the acquisition, you should twitch the starter several times or unscrew the fuel feed valve and each mechanism for its feed. When opening the tap, wait until the fuel is draining, tighten it back and proceed to the next connection until you get to the nozzle. You can open all the taps, and put the lever in the middle position. Next, take up the decompressor, press it and pump it several times. After that, you need to let go and pull it again until it returns to its original state. It remains to click on the decompressor and on the starter. After such simple actions, the engine will start.

When buying a walk-behind tractor, the sales consultant should explain in detail how to start the selected unit. Before using the equipment in your site, carefully study the instructions for the operation of the walk.behind tractor. If you follow all the recommendations of the manufacturer, the unit will last a long time.

Some craftsmen are able to start a single.based tractor without a starter (it is used when it failed). To do this, it is removed, then in the hole of the corolla located behind it, you should pass a dense rope with a node at the end and wind it 4 times around a given part of the walk.behind tractor. Next, you should pull the resulting piston up and turn off the decompressor.

Subtleties of using a walk.behind tractor after a winter break:

• First of all, you need to check the gas tank. With proper winter storage, the tank should be completely filled with gasoline, which merges in the spring, and then fresh fuel is poured.
• If the tank remained empty all winter, then the probability of the formation of dirt and rust in it, for the removal of which the contents of the tank merges, the tank itself is removed, it is washed and returned to its former place.
• Air filter. It must be removed and cleaned in accordance with the operating instructions.
• Carburetor. Unscrewing drain plugs on it, from which the remaining fuel should flow. After the drain is completed, we wrap the corks.
• The same procedure must be carried out with a fuel crane. If you can see that gasoline goes to these mechanisms, then you should eliminate the leak.
• Oil probe in the engine. It should be pulled out and wiped with a rag, after which you need to return the probe back and unscrew again. It needs to determine the presence of oil, which should be no less than the upper mark on the probe. If the oil level is lower, then the required amount should be added. In addition to the oil level in the engine, it is necessary to evaluate its quality. If it looks like a black slurry and has a fairly unpleasant smell of Gary, then it should be completely drained and new.
• Next. how to pull the belt on the walk.behind tractor. You should go to the drive belt, namely, to its tension video. Its tension must be checked in this way: first release the control lever (the video should also be released, while you do not need to squeeze the belt), and then stretch the lever (the video pulls the belt). In case of improper tension of the roller, the craving should be thrown over the links of the adjusting chain.
• The next next in line is the main gearbox in which the oil level should be checked by launching a regular wire into it. The amount of oil should be as indicated in the instructions for the walk.behind tractor.
• Wheels and cutters. Study their stoppers. with poor quality, they should be changed.

Now the engine starts, while it should be wellgated, warm it up for 3-5 minutes. And here some problems may arise.

Why stall the one.axle tractor

Many owners of technology are interested in why one.time tractor stalls. The unit can start right away. But if he works with interruptions or starts and stalls, you should know what to do in this case. In principle, you can figure out what is the reason if the one.axic tractor stalls when starting. To do this, check if the ignition is turned on, is there a fuel in the tank, whether the crane is open. Still check the opening of the air damper, the intake of the fuel, study the operation of the ignition system (if the candle is dry, then you need to clean the carburetor, and if wet. the overkill with the fuel mixture) and the functioning of the starter.

The same.based tractor stalls when tilted if the oil level in the engine is below normal. The same.based tractor stalls under load, if the candle is old, and there are some problems. It happens even when loading the engine suddenly stalled (it may occur when the engine heats up). Heated devices on a motor.cultivator will lead to the fact that the equipment will begin to lose speed during operation.

You should also know why the diesel unoic tractor does not start. The same.based tractor does not start if there is such a problem as the air entering its fuel system, which should be released through air traffic jams (you need to open the fuel valve and spin all the channels there to the nozzles). Also, the same-based tractor diesel can stall when tilted, so you just need to put it exactly.

Reducer of the MROT MROT: device

The gearbox of the Mole Motor Consistent consists of the following elements:

• Gear shaft and asterisk.
• 4 bearings.
• Two parts of the case.
• Roller chain.
• 3 seals.
• Shaft.
• Val with an asterisk.
• Traffic jams.
• Gaskets.
• Plugs.

The reducer is combined, and in it the gear transmission precedes a single.row chain. The gearbox is gear, designed from two shafts to which the gears are attached.

The gears on the driven shaft are fixed static and do not move along. The design of the device provides for the option of gear.

DIY REDUTOR Repair

There are two options for the owners of the MROT motor.cultivator, who failed the gearbox:

• Take it to specialists who will repair the damaged parts of the gearbox quickly and efficiently.
• Engage in elimination of malfunctions on your own.

The first method is priority, since there will be almost 100% guarantee of quality and safety. The second method is risky, and people who are not confident in their own abilities are better not to take on it. The process of eliminating the gear malfunctions is as follows:

• Make sure that the oil in the system is at the proper level and does not follow. If not, share the required volume and eliminate the leak.
• Check the condition of the fasteners of the main nodes. If the open elements are found, tighten them.
• Remove the reducing gearbox and check the condition of its parts and bearings.
• Remove the oil seal and gear oil.
• Scroll and check how the oil seal moves. Perhaps he sits loosely and because of this passes the oil.

It is advisable to perform other actions under the supervision of the master, who thoroughly disgusted the device of the mechanism and can see other causes of the malfunction. As a council, experienced owners recommend not switching gears on the go. Do this only after a full stop of the walk.behind tractor.

How to put an electric starter on a single tractor

If you cannot figure out how to put an electric starter on an agricultural unit, follow the recommendations below:

• To remove the engine flywheel, it is necessary to remove the air filter of the walk.behind tractor to open access to the “native” manual starter for dismantling.
• Remove the protective cover of the node, unscrew the fasteners of the starter baskets and dismantle the flywheel using a special key. Behind it is a key that needs to be unscrewed.
• Next, you need to install a generator for which there is a seat on the engine. All wires easily stand through the hole in the wall of the motor housing.
• Put the generator magnets into the flywheel so that the holes coincide, fix them in this position with the help of fasteners. Heat the crown with a gas burner, and install the device.
• The resulting assembly is installed on the internal combustion engine, the bends and the fixing nut are screwed up.
• Fix the basket, put in place a filter and a protective cover.
• Install an electric steamer, connect to the battery. At the same time, the generator wires are attached to the charging relay. Check the serviceability of the system by launching one.axle tractor.

How to make a hand starter on a single tractor

As in the case of the manufacture of an electric steamer from improvised means, make a hand starter for a walk.behind tractor (Neva, Oka, Cascade, Patriot and others) will be a simple task for a master who has appropriate knowledge.

To assemble a home.made kickstarter, the installation of the handle should be added to the materials described above and the procedure for transmitting the effort, which will replace the operation of the electric motor. The foothold of a hand starter can be made of a thin metal pipe, which will need to be bend in the shape of the foot and install in the hollow hole of the coil. Having collected the device, you should definitely weld it.