How to start the same -based Caiman Eco Max tractor.

TOP-3 CAIMAN 900 mm motor cultivator with Subaru engine

Operating instructions attached to the CAIMAN brand cultivators. contains recommendations for the assembly and adjustment of mechanisms. To control the engine speed, a lever or a rotary regulator is used that has the position of stopping the power unit. To select speed and direction of movement, a separate lever is used, which moves straight or sector. Before starting operation, the engine is refueling with motor oil, which has a viscosity recommended by the manufacturer.

The design of the installations provides for a safety fuel valve, which opens before starting the engine. After the work of the NEC cultivator motor or similar equipment, it is recommended to immediately start movement, simple leads to overheating and the formation of a carbon in the combustion chamber. Switching speeds is performed only with a squeezed clutch lever. To ensure uninterrupted operation, it is necessary to inspect and lubricate the cables and traction of control annually (according to the attached map).

User manual

Service

In order for the Forza motor blocks to last as many time as possible, it must be correctly used and maintained.

• It is necessary to use the unoic tractor only for its intended purpose;
• You can not change the factory settings or carry out re.equipment on your own;
• It is forbidden to come close to the rotating parts of the Forza motor block or mounting equipment;
• Before starting maintenance, it is necessary to let the device cool;
• Only official attachments should be used, otherwise the One.based Forza Tractor may fail;
• Before each exit, visually check the details of the machine for wear or their unnatural position;
• After each work, it is necessary to clean the one.axic tractor from grass, foliage and dirt in order to prevent fire when the engine heats up;
• Contact of the device with water is prohibited, since jamming of mechanisms can occur, especially for control knobs;
• Replace motor oil after a walk.behind tractor every 20 hours of work. It is necessary to use lubricants from the 10W-30 series;
• Every 100 hours of work should be changed transmission oil. It is recommended to use TAP-15V, TAD-17I or their analogues.
• After 300 hours of operation, it is necessary to replace air filters, check the condition of the spark plugs and adjust the clutch cable.

Running

The main thing is to start using the One.based Forza Tractor properly. Further performance of the device will depend on the assembly and the first motorized hours of operation.

Immediately after the assembly, the use of the walk.behind tractor at full power is not allowed, since the oil has not yet passed through the entire system, and the engine details must be running. This is a procedure when the One.based Forza Tractor is used at half the maximum power. An ideal option is to ride with an empty trailer when there is a slight load on the engine of the device.

Then, you can start operation at half the maximum power. For example, if the plow can be immersed in the ground by 18 cm, then when running out, it should be included in only 9.

The main malfunctions

No matter how carefully the owners treat the Forza motor blocks, periodically they fail due to different circumstances. Therefore, you need to know how to eliminate simple malfunctions.

If the engine does not start, then these are the main reasons and ways to solve the problem:

• Check the presence of fuel;
• Configure the position of the throttle;
• Check the light of the ignition and wires to it, see if there is a spark;
• The air filter clogged;
• Water got into gasoline;
• Garbage got into the fuel tank;
• Set up the correct mixture in the carburetor.

Forza unoic tractor does not start:

• Adjust the position of the throttle;
• Clean the air filter;
• The light of the ignition has become unusable or contact with it;
• Bad fuel was used.

Caiman 403

one.axle tractor on a pneumatic wheel with tires, size 4.00-8. The tread pattern is specially designed for movement on loose soil.

The drive mechanism is a 4-clock gasoline engine with air cooling-Subaru EP17, with a power of 6 liters. With. The motor is distinguished by a special design of the lubrication system and high.quality air filtration. Removable cast.iron sleeve and forged crankshaft guarantee a long service life. Subaru engine resource declared by the manufacturer is 2500 hours.

• The width of soil processing is regulated within 350-500 mm at a depth of 250 mm.
• Power selection shaft instead of a belt drive for attaching equipment. Excludes the probability of slipping and allows you to work in the most difficult conditions.
• Two front and two rear speeds make it possible to choose the optimal operating mode.
• The differential blocking function gives the apparatus excellent maneuverability and allows you to perform quick reversal, regardless of the equipment used.
• The height.adjustable steering handle with the possibility of rotation to an angle up to 180º.

Caiman Eco Max 50s C2

Productive cultivator equipped with a 4-stroke gasoline Subaru engine with a capacity of 5 liters. With. Three pairs of soil mills made of hardened steel provide high.quality plowing of the earth, regardless of the type of soil. Side discs prevent random damage to decorative plants and flowers. Soil processing width is 600 mm, with a depth of plowing 320 mm.

The distinctive features of the model include:

• The presence of rear gear increases maneuverability and facilitates the work in areas with complex relief;
• An ergonomic handle, which is regulated in height in three positions;
• A reliable chain reducer gearbox provides a high.quality transmission of torque from the engine with minimal power losses;
• Adjustable plowing width;
• Reliable Japanese Subaru engine with a chain timing drive.

The functionality of the cultivator can be expanded through the use of auxiliary attachment equipment. the cigarette light, the plow, the potato.cutter or the pollen. It is also possible to install soil.spaced with weighting and trolleys. Installation of attachment equipment is carried out using a clutch.

Recommended processing area for the Caiman Eco Max 50s C2 Caiman, is 1500 m2.

Lifan

These motors for motor blocks have appeared relatively recently, but they are already very popular among gardeners and commercial organizations engaged in agriculture. Consider the main characteristic features of these engines:

• Products are produced by various capacities;
• Both diesel and gasoline plants are present here;
• the engines have a long service resource;
• moderate power and value of working revolutions;
• low cost of devices;
• universality of these devices;
• improved traction of Lifan engines;
• compact dimensions (motors are easily mounted).

Also, these installations do not differ in high gluttony in frequent operation (engines do not consume a large amount of fuel, as well as oil, in comparison with other similar models from other manufacturers).

Important! Despite the large list of qualities of such power plants, the models appeared on the market relatively recently, because of which they did not get widely widespread. It is also necessary to monitor the condition of the candles during operation, there are frequent cases when they are poured.

Another manufacturer of power plants for motor blocks of the Salute brand. These units are in great demand. The following distinctive features are characteristic:

• moderate capacity and number of working revolutions;
• relatively low cost of devices;
• long.term resource of motors service;
• the presence of all consumables and spare parts in the free sale;
• unpretentiousness to fuel;
• engines do not eat a large amount of oil;
• relatively small sizes of power plants;
• Due to the engines, good cross.country ability is ensured.

Despite a large number of positive points, during the operation of these engines, one can also encounter some disadvantages. The most pronounced from the minuses is the high cost of spare parts (so that the engine serves for a long time, consumables need to be changed quite often).

It is worth noting that not all brands of motor units on the motoblocks of fireworks were considered here, other manufacturers of power plants are also found, but their characteristics and indicators are somewhat worse than the models mentioned here.

ACME is relatively not expensive

Features of operation and maintenance

A lot of time has passed since the founding of the brand. The company is constantly working to expand the assortment and improve existing equipment. Despite the fact that now assembly production are located in 16 countries of the world, Caiman continues to delight consumers with high.tech technology, which fully meets modern requirements.

At all CAIMAN plants, regardless of the geographical location, a single quality standard is valid, which practically excludes the likelihood of a defective product on the market. CAIMAN gasoline cultivators equipped with Subaru engines are reliable. As practice shows, subject to the provisions of the operating manual, the service life of cultivators significantly exceeds the 2500 hours declared by the manufacturer.

The main requirements of the manufacturer include:

• It is forbidden to use gasoline below the AI ​​92 brand. Failure to comply with this requirement will lead to sad consequences. breakdowns of the elements of the power system and a significant reduction in engine service life, up to the repair. Signs of refueling with non.infected fuel are problems with launch, a noticeable reduction in power, interruptions in work, increased consumption.
• Follow the schedule of maintenance. In this case, consumables recommended by the manufacturer should be used. It also applies to motor and transmission oil.
• Do not store an open.air cultivator. He should stand under a canopy or garage.
• Do not allow the appearance of foci of corrosion.
• Any operations, whether maintenance or repair, should not contradict the provisions of the instructions for operation.

First start and run

At the stage of the running.in, an intensive production of the involved surfaces of the engines and the transmission of the cultivator occurs. The procedure is accompanied by smoothing microscopic irregularities, improving the quality of the rubbing surfaces with a decrease in the friction coefficient, as well as calibration of the established clearances.

Correctly running.in. the key to long.term operation of the equipment. This procedure is performed during the first 10 hours of continuous operation, from the moment the engine is launched. Operation is carried out in gentle mode. the engine should be loaded no more than half of the rated power. At the same time, the first 30 minutes is drove the equipment at idle.

After 10 hours, the replacement of the engine oil should be performed.

Conservation for the winter

Despite the fact that most CAIMAN cultivators and motor blocks can be used all year round, the owners of summer cottages usually do not work in winter, leaving the device for storage.

There are several simple rules, the observance of which will allow the cultivator to safely wait out the cold:

• Conservation begins with cleaning surfaces from pollution;
• It is necessary to store the device in a dry room with normal humidity, in order to avoid the appearance of foci of corrosion;
• Transmission and motor oil should be filtered or replaced;
• The battery is best stored separately, in a warm room; since it is sensitive to negative temperatures;
• 20-30 ml of engine oil should be poured into the cylinder, after which the crankshaft is scrolling several times-this will protect the surface of the sleeve from corrosion.

Possible malfunctions and repair

Persons without experience are strongly not recommended to engage in independent repair of equipment. It is better to contact a specialized service center. they are in every major city.

The main problems of Caiman cultivators with Subaru engines are:

• Insufficient motor power. Probable reasons: clogging of an air filter or muffler, incorrect carburetor settings, low compression.
• The engine gets very hot. The probable reason is the malfunction of the cooling system.
• The motor stalls under load. The probable reason is the clogging of the fuel filter, incorrect carburetor settings.
• Cutters do not rotate when the engine is running. The probable reason is a malfunction of the clutch mechanism.

Non.mounted equipment

To most fully involve the capabilities of cultivators, use a variety of attachments. For cutting the beds, weeding a row spacing from weeds, hilling of plants, harrowing the soil, many auxiliary tools have been created, with which you can do more work with less physical efforts.

Based on the features of the CAIMAN cultivator model, they choose the necessary attachments:

Thanks to the collapsible design of soil mills, you can choose the optimal soil processing width, if necessary, install pneumatic wheels.

The small mass of Caiman cultivators somewhat limits the owners in the choice of additional equipment, in such cases, metal wheels with primers are used for weighting and better cross-country ability, and cargoes-designs are used.

The Caiman Neo 50S C3 motor cultivator, thanks to a full.fledged gearbox, is able to work with hinged units no worse than a walk.behind tractor. In the configuration with milling cutters, plow, wheels with primer, potato.cutter, the machine shows unique possibilities:

• Mills and plows will help in processing all types of soils.
• The coupling allows you to use not only hanging equipment from the official site of the manufacturer, but also from third.party walk.behind shoes.
• The adapter can turn a motor cultivator into a mini tractor, where the operator will work sitting.
• Trailers will allow you to transport any load up to 400 kg. at a distance.
• It is also possible to aggregate potato and potato.cutter for planting and collecting vegetables.
• Mitch will ensure the cleaning of the territory from weeds, and will also help in hay harvesting.

Operation and maintenance

Running

According to the design, Caiman cultivators are mainly similar, except for light versions. have manual launch, front transport wheel, differ in engines and additional functions.

• Open the gas pipeline
• Close the throttle
• Install gas lever on the maximum position
• Wipe the starter cord
• open a throttle and reduce gas.

The run.in the cultivator involves the lapping and production of the main components and mechanisms of the machine, the chassis and transmission in gentle mode. Therefore, after starting the engine and working at low speeds for several minutes, the 8-9 hour work cycle with 50% load should be launched for several minutes.

Caiman cultivator operating instructions. download.

The main malfunctions

Experienced owners recommend strictly observing the mode: work/rest, regardless of engine power. For the durable operation of the motor, it is necessary after the development of the full fuel tank to give the cultivator rest for 15-20 minutes to cool the engine.

With long.term high loads, the shaft with mills can stop rotating, slipping, it is also a hint that you should take a break to cool the engine.

Air filter cleaning, checking oil level, preventive inspection. basic simple rules for the operation of the cultivator. It is important to give the engine to warm up before work. When processing solid soil, plowing should be carried out in two passes without overloading the car. For the first time, the cultivator will process the soil to a depth of 15 cm, and for the second passage you will achieve 25-30 cm depth.

The main malfunctions:

• The engine does not gain power. possibly clogging of the air filter, the carburetor adjustment, insufficient compression, clogging of the muffler are disturbed.
• Excessive heating of the motor. impaired air access for cooling.
• An unclosed fuel valve with an unemployed engine causes a candle filing.
• Stopping the motor under load. clogging the fuel filter, the carburetor adjustment is violated.
• Cutters do not rotate when the engine is running. the occurrence of defects in the adhesion mechanism.

Most often there are problems with belts. the problem is eliminated by replacing new. When eliminating breakdowns, it is necessary to clearly follow the recommendations of the operating instructions. if the manufacturer is possible, the sequence of the necessary operations is indicated by the manufacturer.

Oil

It should be borne in mind that Caiman cultivators are demanding on proper quality of gasoline. According to the regulations, the first replacement of the SAE 30 brand is carried out after 5 motorized hours of work, the next. after 25 hours, in the future after 50 motorized hours. Caiman cultivators work on AI-92 gasoline.

Operation and maintenance

Running

According to the design, Caiman cultivators are mainly similar, except for light versions. have manual launch, front transport wheel, differ in engines and additional functions.

• Open the gas pipeline
• Close the throttle
• Install gas lever on the maximum position
• Wipe the starter cord
• open a throttle and reduce gas.

The run.in the cultivator involves the lapping and production of the main components and mechanisms of the machine, the chassis and transmission in gentle mode. Therefore, after starting the engine and working at low speeds for several minutes, the 8-9 hour work cycle with 50% load should be launched for several minutes.

Caiman cultivator operating instructions. download.

The main malfunctions

Experienced owners recommend strictly observing the mode: work/rest, regardless of engine power. For the durable operation of the motor, it is necessary after the development of the full fuel tank to give the cultivator rest for 15-20 minutes to cool the engine.

With long.term high loads, the shaft with mills may stop rotating, slipping, it is also a hint that you should take a break to cool the engine.

Air filter cleaning, checking oil level, preventive inspection. basic simple rules for the operation of the cultivator. It is important to give the engine to warm up before work. When processing solid soil, plowing should be carried out in two passes without overloading the car. For the first time, the cultivator will process the soil to a depth of 15 cm, and for the second passage you will achieve 25-30 cm depth.

The main malfunctions:

• The engine does not gain power. possibly clogging of the air filter, the carburetor adjustment, insufficient compression, clogging of the muffler are disturbed.
• Excessive heating of the motor. impaired air access for cooling.
• An unclosed fuel valve with an unemployed engine causes a candle filing.
• Stopping the motor under load. clogging the fuel filter, the carburetor adjustment is violated.
• Cutters do not rotate when the engine is running. the occurrence of defects in the adhesion mechanism.

Most often there are problems with belts. the problem is eliminated by replacing new. When eliminating breakdowns, it is necessary to clearly follow the recommendations of the operating instructions. if the manufacturer is possible, the sequence of the necessary operations is indicated by the manufacturer.

Oil

It should be borne in mind that Caiman cultivators are demanding on proper quality of gasoline. According to the regulations, the first replacement of the SAE 30 brand is carried out after 5 motorized hours of work, the next. after 25 hours, in the future after 50 motorized hours. Caiman cultivators work on AI-92 gasoline.

Reviews

Leonid, St. Petersburg:

“Caiman Caiman Terro 50s C2 I have 3 years. Adapted to work with him, but now I’m not getting rid of. Of course, there are their own characteristics, like any technique, but reliability is amazing. If you use it clearly out of purpose, wisely, it works flawlessly “.

Cyril, g. Zelenograd:

“I acquired the French motor.cultivator CAIMAN 60S D2, the price compared to Chinese machines, I think normal. The model likes the fact that the powerful 6 l.With., The engine is good Subaru. The first time, of course, some areas were difficult to pass. But this year the earth has become completely different in the spring. With reverse and rotary handles work fine. Pneumatic clutch simplifies work. Small car, the coupon is adjustable. In general, I am very pleased with. Such a technique is not one day. Operating instructions are unsuccessful. Whoever faces the first time with technology will not figure it out on their own. “.

Description and basic characteristics

Caiman Vario 60s

Thanks to the competent construction of the structure, this unit is able to process even the virgin lands, and this is given that it weighs only 57 kg. The area of ​​work may exceed 25 acres. There are no wheels in this model, but in this case they are not needed, because the movement is provided by soil cutters. Despite its compact dimensions, this unoic tractor is able to reach a depth of 25-33 centimeters, depending on the type of attachment equipment.

The engine in this walk.behind tract is Subaru Robin Bi 17, assembled in Japan, differs primarily by high endurance and reliability. The indicators of its power are 6 liters.With., and it is driven by manually (starter). Lack of overheating provides stable air cooling.

The list of the main characteristics of the Caiman Vario 60S is as follows:

• Smooth speed switching. It became available, thanks to the new Vario Automat gearbox, consisting of 3 speeds (reversible, slow and standard).
• Adjustable handles. You can change their placement in 3 planes. Thus, control can be configured for yourself.
• Turning. Even with a plow installed (or other tool), the device can quickly unfold 180 degrees.
• Reliable engine protection. When working with the ground in the unit, something is constantly flying, and the engine is the most vulnerable detail, so now it has additional protection.
• Quality brakes. The drum type of brakes is used here, which allows you to quickly stop the one.axle tractor on the slopes.
• Great variability of equipment selection. It is ensured thanks to the three.and.line shaft.
• The center of gravity is directed to the back of the unit, which increases its controllability.
• Quick Drive Inverter. allows the walk.behind tractor to quickly start in any direction.

The engine of this unit is a Japanese

CAIMAN VARIO 60S TWK

This version of the walk.behind tractor is slightly different from the previous. The engine here is a little different, namely Subaru EP 17, also from Japan. The motor of this model is four.stroke and is also equipped with an air cooling system. If you can only manually start the engine in 60S, then here, in addition to this method, there is another option for electric launch. The depth of plowing in both versions is the same and depends mainly on the installed equipment.

All other characteristics here are the same as in Caiman Vario 60s. That is, in fact, this is just an improved version with another engine model and the function of electrical starting.

CAIMAN VARIO 70S TWK

This model of the walk.behind tract is equipped with a new Subaru EP 17 OHC engine with increased strength and resistance to serious types of work, for example, processing is intelligent to greater depth or high weight transportation. Four.stroke engine, with one cylinder and sleeves made of cast iron. He practically does not feel temperature fluctuations and is able to act effectively even in a 30-degree frost.

In this video, you will learn the pros and cons of the CAIMAN Vario walkover:

The strength is also ensured by the lack of serious vibrations from the motor, which can loosen fasteners. Air overheating system here. As for power, this model is able to develop 7 liters.With. The launch of 70S TWK can only be done manually, and for refueling the tank will need 3.4 liters.

As for the gluttony of this version, here it is a little higher than consumption indicators in 60s. On average, approximately 2 liters will be spent in an hour, however, with increased loads, 3 liters can reach. The main characteristics of the CAIMAN VARIO 70S TWK motornote are the following points:

• Transmission. There is an automatic switch. The total box consists of two gears. the rear and front. The transition between them is carried out smoothly, so the device is considered a very durable. The part of the part is covered with special waterproof material, and the factory lubricant is enough for a long time, most likely it will not have to be changed at all.
• High.quality steel in a gear mechanism and chain gearbox. This is qualitatively distinguished by the Caiman Twk Unoa Caiman Twk tractor from other analogues, because this parameter directly affects the durability of the unit.
• Mobility. This uniform tractor is easy to dismantle and compactly fold, and this is extremely important during transportation.
• Direct tires with a deep tread. This type of tire can calmly plow already processed areas, because with this tread they will not be linked in the ground. Also, these tires fluid well with the surface, even if this surface is rocky.
• High.quality drive belts.
• The ability to install an electronic starter.
• It is recommended to refuel this unoic tractor with high-quality fuel, no lower than AI-92.
• Special wheels for wheels included.

Caiman 403

This unoic tractor differs from the previous ones in the first place in that it is equipped with a box with 4 gears. The engine in it is Subaru-Robin Ep 17 OHC. This device is heavier than other representatives of the list (90 kg), but at the same time the differential lock was added to it.

There is also a larger volume of the tank where 3.6 liters fitting, and maximum power within 6 liters.With. In all other parameters, this model is similar to the rest.

Caiman 320

Another heavy representative of the line of motor blocks from Caiman weighing 90 kg. The volume of the fuel tank in it is the same as that of the CAIMAN 403 motornote. But there are more speeds: 3. for front.line and 2. for the rear.

There are many transmissions in this apparatus

Four.stroke Subaru EP17, with a maximum power of 6 liters.With. In fact, this is almost the same 403, but with a large number of transmissions, which may well be useful when plowing difficult surfaces.

Non.mounted equipment

For all three Caiman Vario models, the list of supported attachments looks the same and consists of the following devices:

• The brush. this device is actively used to clean medium and large territories from garbage and snow. They are also actively used when cleaning sidewalks from leaves in the autumn season.
• Trailer. in this case, the unoic tractor is able to play the role of a car. Of course, the same weight as the car, he will not be able to transport, but still for cargoes of medium severity, it is quite suitable. In appearance, this is an ordinary trailer, just with a slightly modified mount.
• Rotor braid. this type of device is designed for a cutting of a vegetation cover of both an agricultural type and weed. It is also often used by farmers when harvesting feed. This type of equipment is often used with lighter models of motoblocks, for example, with Caiman Vario 60S TWK.
• Snowman. for small layers of snow and in general surface purification, you can use a brush. However, if this is a large layer of snow cover and sidewalk/road must be cleaned carefully, then the snowman will already be needed.
• Double.rowing hip. this equipment is necessary to smear the furrows in order to further plant seeds in them. In some cases, they are used to increase the level of loose soil. A two.row perch is needed in order to make two parallel furrows so that in general the site is planted smoothly and neatly.
• Cultivator mill. mainly these devices are used to process heavy soil types. Before using devices of such complexity, it is advisable to familiarize yourself with the operating instructions.
• The plow. this device is intended for light plowing of the earth, turning its upper layers and instillation of fertilizers.
• Light-off shovel-can be used both for cleaning roads and areas from snow, and for the movement of earthen masses.
• Soil.bearing. this concept means certain modifications of the wheels intended for work in difficult conditions, with loose and already cultivated land. When driving, they deepen, but only contribute to the movement.
• Potato trailer. there is nothing special to tell here, it is used to dig potatoes. Often used with the CAIMAN VARIO 60S motoblock or other light model.
• An adapter is a device that makes life easier for someone who is engaged in earthwork. A cabin analogue, with a seat and control levers.
• Lawn mower.

User manual

Instructions for walkways contain many technical subtleties and data, however, in total, 4 main points can be distinguished:

• Playing the walk.behind tractor. A very important point, since no one can guarantee the correct functioning of the unit without proper run.in. You need to start with idle revolutions and then gradually increase the power, along the way will switch the transmission. After that, you need to test it a little in working mode.
• Study the model of the model. These are already technical subtleties, schemes, which, however, must be familiarized with, in which case, immediately determine the malfunction.
• Study the procedure for maintenance of the apparatus. This includes a change in oil, fuel, packaging during storage/transportation, etc.D. These parameters vary, depending on the model, because the fuel consumption of the CAIMAN 320 motorlock and, for example, 60S will be different.
• Each instructions have a list of possible breakdowns and methods of their independent correction.

This is interesting: the choice of the engine for the one.axic tractor Neva.

Before starting work, be sure to check:

Characteristics of the Motoboblok SAIMAN VARIO 60S

Caiman Vario 60S TWK is a high.quality and reliable unoic tractor that is suitable for virgin processing, as well as soft plowed soil.

Distinctive characteristics of this technique:

• Professional motor with upper Subaru EP17 valves with a capacity of 6 liters. With.;
• Cylinder from cast iron, providing reliable and durable work;
• a specially designed gearbox that allows you to replace the spare parts that have come to a malfunction. The presence of a moisture.resistant gearbox sealing allows you to protect the internal bearings from pollution and moisture;
• gearbox with two speeds forward and one back, as well as a special speed under the plow;
• Aggressive tread on pneumatic tires is responsible for the cross.scale of the walk.behind tractor and adhesion to the surface to be treated;
• Innovative transmission Varioautomat provides the optimal mode of operation of the unit;
• The handle is adjusted vertically under the growth of the operator, as well as horizontally, allowing the work at an angle, with a minimum contact with the soil;
• Sushnik with double.sided sharpening to adjust the depth of soil processing.

DIY malfunctions and repair

The frequent malfunctions of the equipment include interruptions in engine operation that arise due to insufficient fuel level in the tank. The level is determined by a visual inspection, a canister with an extension nose is used for a piece. Malfunctions in the work arise when foreign particles get into the carburetor. The repair of the cultivator is to dismantle and subsequent disassembly of the node.

After washing with gasoline, the node is going to re.use sealing gaskets is not recommended.

Caiman cultivator is equipped with an air filter, the element clogged with dust worsens the operation of the motor under load (up to stopping). To remove pollution with your own hands, it will be necessary to rinse the foam element in warm water with a detergent. Then the part is dried and impregnated with engine oil (fluid volume 15-20 ml). The manufacturer recommends cleaning every 10 hours of engine operation. Problems with starting arise when improperly adjusting the air damper or with dirt clogged with mud.

The design of the cultivators engines provides an oil level sensor that automatically disconnects the ignition with a lack of lubrication. The owner adds oil through the hole located on the motor crankcase. The power unit stops when the valve is broken in the fuel tank cover or damage to the components of the ignition system (coil, wires or a special candle tip). The failed parts are subject to replacement.

A knock when operating the engine indicates the use of gasoline with a low octane number. The use of non.data fuel causes the vibration of the power plant (with the sudden vibration, it is recommended to check the tightening of the engine mounting bolts). If, after pouring fresh fuel and warming up the engine under load, the knock does not disappear, then the condition of the curvature mechanism is checked. According to the owners, repairs are recommended to be carried out in dealerships.

Motoboblock malfunctions

In this topic, we will disassemble the malfunctions of motor blocks and cultivators of all brands, salute. Neva, bison, etc.D., and their elimination and repair. Most of the malfunctions are characteristic of all types of motoblocks, their engines and other nodes.

It often happens that a previously proper unoic tractor, which served for several years, suddenly loses its power.

Malfunctions of the ignition system

The engine will not start with faults in the ignition system. Why is this happening? The sources of the failure can be magneto, high.voltage wire, cap and spark plug. External inspection check the cleanliness of the parts of the ignition system. Dirt and moisture cause a breakdown of high voltage to the housing. The lack of spark is with poor contact of the cap with the central electrode of the candle.

A weak spark indicates the poor spark plug. It is necessary to check the gap and condition of the electrodes. The gap is checked with a probe. It usually is 0.8 mm. If necessary, remove the burning from the metal parts and the insulator. Candle replacement is recommended.

The condition of the parts of the piston group affects the readiness of the motor as a whole. They work in difficult conditions. Under load, the rubbing surfaces heat up. Cylinder, piston and rings are responsible for an important indicator. compression. Low compression degree in the cylinder will indicate the replacement of parts.

You should also check the inlet and exhaust valve. They should fit tightly to the saddles. Muffler. the last point on the path of the exhaust gases. On the walls of the muffler, combustion products are gradually deposited, and the engine stalls. For the normal passage of exhaust gases, the walls should be periodically cleaned of soot.

Experts advise adhere to all the manufacturer’s recommendations. You can not overload the unit.

Fulfillment of all requirements will extend the life of the mechanisms.

Before starting work, the owner must familiarize himself with the operating instructions.

The same.based tractor is one of the most useful economic units. Even a simple and not particularly powerful car is able to significantly facilitate the care of the garden and the adjacent territory. At the same time, the same.based tractor is a technique that tends to break. Let’s look at the most common breakdowns of the agricultural unit, their causes and methods for eliminating on their own.

Almost every engineer of the walk.behind tractor, regardless of the brand and model of the agricultural unit, came across a problem in which the same.based tractor starts up and stalls after 5 minutes of work. The main causes of this breakdown lie in the problems with the supply of fuel and breakdown of the ignition system of the machine.

As practice shows, if the unoic tractor stalls when working, then its owner should immediately inspect the details of the fuel supply system. First of all, turn out and look at the candle. if it is completely dry, this indicates that the fuel does not fall into the engine cylinder.

After that, you need to make sure that a sufficient amount of fuel is present in the fuel tank. If there is gasoline and it is enough for work. inspect the fuel valve. it is possible that it is in a closed position. To launch the walk.behind tractor, just open the fuel valve and continue to work with the unit.

Another reason why the same.based tractor starts up and stalls after 5 minutes of work is to break down the ignition system. To determine that the unit is faulty for this reason is quite simple. take a look at the candles. if they are wet, then the malfunctions appeared precisely in the ignition system of the walk.behind tract.

• Remove the cover that serves the elements of the ignition system;
• Turn the flywheel of the motor until the contacts go out in Magneto;
• Using a special probe, measure the gap between the “anvil” and “hammer” of the ignition system of the motor block;
• After that, turn the flywheel until the moment the piston of the walk.behind. In this case, the latter must reach its upper point;
• Take the flywheel again until the moment when you hear a characteristic knock. this means that a overtaking coupling worked;
• Then turn the flywheel in the opposite direction so that the label on it coincides with the label on the body of the walk.behind tractor;
• Install the gap between the interruption contact and the fist. it should be 0.3 mm;
• At the end, fix the cam with a screw located above the part, and install the protective cover back into the motor block body.

After the above actions, the same.based tractor will no longer stall under load. The main thing in the event of such problems in the future is to try to quickly eliminate the breakdown, so as not to give the main mechanisms of the walk.behind tractor to be increased to wear and wear.

It is also often a household unit stalls when tilted. This indicates an insufficient amount of fuel in the fuel tank. If you put the unit in a horizontal position, pull out the starter cable, and the engine starts, then you will need to add gasoline into the tank.

Among other typical malfunctions of the walk.behind tractor, a number of such breakdowns can also be distinguished:

• The aggregate motor hits the return. this indicates the use of poor.quality fuel for refueling the unit. In this case, you will have to not only replace the fuel, but also thoroughly rinse the fuel pump and fuel supply hoses;
• The same.based tractor works with jerks. the reason for this lies in the insufficient heating of the motor. Be sure to drown out the engine, wait for it to cool completely, and again start the motor, giving it at least 10 minutes for full heating;
• The motor block does not noticeably pull, the engine power has decreased. in this case, you need to check and, if necessary, clean the air and fuel filter. Another reason for this breakdown lies in the wear of the magnesium magneto. It is best to immediately replace the part without trying to restore it.

The owner of both gasoline and diesel motoblock is equally often faced with this kind of malfunction. In any case, you need to immediately stop working with the machine, and as soon as possible to eliminate its breakdown.

Often, when working with an agricultural unit, loud uncharacteristic sounds from its muffler are clearly heard. At the same time, the same.based tractor also smokes strongly and stalls. To be able to eliminate the malfunction with your own hands, you must, first, determine its essence.

Most often, the same-based tractor shoots the muffler due to a number of the following problems:

• An excess of motor oil in the fuel mixture. in this case, you need to drain the remnants of the fuel, rinse the fuel pump and hoses, and pour new fuel with smaller oil;
• Incorrectly exhibited ignition. if the mechanism works late, then this leads to the appearance of atypical shots that are clearly audible in the muffler area. In such a situation, you should immediately set the correct gap between the electrodes of the healing system of the walk.behind tractor;
• Incomplete fuel combustion in the motor cylinder. Repair of the motor block engine in this case implies disassembling the piston group, thorough washing and drying of the motor cylinder, as well as tuning the carburetor of the motor block.

Repair of the CAIMAN cultivator gearbox with your own hands

Details: Repair of the CAIMAN cultivator gearbox with your own hands from a real master for Promotobloki website.ru.

To swim and saturate the soil with oxygen before sowing plants will help the CAIMAN cultivator. The equipment for the land work of the French manufacturer is equipped with Japanese four.stroke engines, economical, and with a large capacity margin. New developments have been delivered to the market, as it has been mastered recently, since 2003.

Among the many techniques of the same name, present a brand from the most profitable side is difficult. The sophisticated buyer is no longer surprised by the novelties. It is necessary to attract his attention with an exclusive. So, considering the gasoline cultivators of Caiman, it is necessary to take as a basis the manufacturer’s information:

• CAIMAN supplies all supplied to cultivators with four-stroke gasoline engines Subaru-Robin, Kawasaki;
• cultivator mills of the Razor Blade type are made of hardened steel;
• A stamped frame with a handle adjustable in 2 planes;
• The gearbox is sealed with lifelong lubricant, if necessary, is disassembled, the chain drive;
• a system of reducing the load on the spine Right Balance;
• wide network of service centers;
• Warranty period of 5 years to amateurs, 3 years to professionals.

Correctly note the reviews on the tools of this brand on user forums. There are many Комментарии и мнения владельцев, we list some of them:

• The instructions were issued common for all gasoline models. It describes in detail the specification, the procedure for repair and security. The procedure for working on equipment missed. Those who see the equipment for the first time have much tormented while they were adopted to work.
• Caiman cultivators are collected in Kaluga, the informed user claims.
• Caiman cultivator with a Subaru engine of Japanese production is produced by the series “Subaru E-16 Premium”, engines from China “Subaru EP-16”. See what is on the proposed model. The cost is the same.
• The layout is uncomfortable, you can get the spark plug only after the hose of gasoline supply hose.
• Initially, when unpacking, it was found that the clutch cables were wrong.
• The engine is demanding of the quality of fuel, gasoline from unscrupulous refueling creates a lot of problems, but understanding comes after repeatedly cleaning the fuel and oil drilling system.

This is not a complete list, there are probably still Комментарии и мнения владельцев, positive reviews are very brief and rare. Caiman cultivators are higher than the average mark.

The horizontal shaft of the Subaru engine fully transfers the load to the working tool. The operation of the mechanism is accompanied by a lower noise, thanks to the engine. The engine is attached to the bed, communication with the gearbox below. belt transmission. Caiman cultivator gearbox transfers torque from the chain leading to the driven star. If the model is equipped with a reverse, reverse, a conical coupling is installed on top. The axis of the driven sprocket goes beyond the gearbox, which allows you to install soil.spaces and wheels. At idle, the Caiman cultivator belt does not pass the torque to the coupling. To do this, you need to squeeze the clutch on the handle, take the tension. In this case, the tension video changes the trajectory of rotation of the belt, and it transfers an effort to the gearbox.

Design features of the mechanism allow the cultivation of virgin and deposit lands. However, the Kaiman cultivator knives are not sharp, so they tear the roots of bushes and perennial weeds, without grinding.

Almost all models have a reverse, which makes the control of units and a reversal accurate. However, the models adapted for processing dense soil and virgin soil cannot be light, and their weight is 46-57 kg. Transportation in a car is difficult.

Caiman cultivators are a complex technique working in difficult conditions. Even with timely maintenance, it is possible to replace not only consumables, but also eliminate breakdowns. It is necessary to follow the instruction manual. If it allows independent repair, then the instructions indicate the sequence of operations. Caiman cultivator repair is carried out within the warranty period in the service center. Specialists are maintained if the unit has already been removed from the guarantee. Repair workshops are provided with details for the repair of the delivered equipment. There may not be the right part in the online store, in the center it must be. There is hope that it is in the workshops that spare parts for Caiman cultivator will sell good quality. Here you can buy branded:

Hanging guns for equipment will also sell here. With a skillful approach, any work in the garden can take several hours instead of multi.day physical exercises with a chip and a shovel. The plow can be drawn with dumpy plowing dense soil.

The hillock will cut the furrows for planting, in the summer will pin the earth to corn and potatoes. Poloiers will pass through the aisles without harming cultivated plants. Clctions and adapters will help expand the area of ​​equipment use.

It should be noted that the models under consideration can be attributed to the class of professional power and functionality.

CAIMAN 50S cultivator in the ranking of the same tools of this company takes 6th place. The model is installed by the Robin-Subaru EP16 engine, compared to others, the compact device weighs 46 kg, but without reverse. This model is not able to install rear equipment on the coupling. The output capacity is 3.7 liters. With., the volume of the fuel tank is 3.4 liters. The processing width of 60 cm at a depth of 320 mm makes the cultivator suitable if you need to plow the area up to 15 acres. The tool is 23990, at the price of the manufacturer.

Much more functional cultivator Caiman 50s C2. In the rating of models of his company, he took a leading position. Distinguishes it from the previous model the possibility of reverse.

With the same energy indicators, the course back creates significant relief in management. The shaft protruding from the gearbox allow you to use the rear clutch and attach the plow in the kit in the potato worker.

Only one of the presented models of cultivators. Caiman 60S D2, is equipped with a pneumatic drive. The hero easily processes with cutters dense earth with a capture of 90 cm.

To take entirely depth, the unit will require 2 entry. For the first time, he will tear the turf 15 cm deep, plowing a second time by 32 cm.