Install a fishing line for a trimmer for Patriot grass. How to remove the coil and replace the fishing line for the trimmer

Installation of fishing line on a trimmer for Patriot grass

Trimmer for grass is the most common unit used to cut grass and cut small shrubs. This device is distinguished by its simplicity in maintenance, simple management during operation, and even women cope with it even a small weight.

It is no secret that for the high.quality performance of herbal mowing work, the correct selection of a cutting tool is required. As the latter in trimmers, special cutting nozzles (wheels, knives) or trimmer heads with fishing line inside are used.

Nozzles and a fishing line for a trimmer are a consumable tool, but if the knives can be sharpened, then when spending the fishing line you need to replace it. In this article, we will tell you in the most detail how to correctly replace the fishing line for the trimmer.

Coil with one working antenna

The simplest version and simple sequence of actions:

• Bobbin dimensions and the length of the factory factory winding determine the recommended length for winding the braid fishing line. 2 5 m.
• One end of the spit line is inserted into the fastener technological hole inside the bobbin.
• The fishing line for the trimmer is wound on the drum during the reverse rotation of the bobin in the direction of the trimmer product for the grass. as a rule, on the inside of the bobin, the arrow indicates which side is wound.
• A small part of the spit line remains free so that it can be pulled out. it is fixed in a special groove on the inside of the coil designed to hold the winding when the coil is collected in working condition.
• The left end of the mowing fishing line passes through the hole of the outer part of the coil.
• Half of the coils are collected and installed on the bar of the trimmer device for grass.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Adjustment of a trimmer carburetor for STIHL grass. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Winding process

If your coil is designed to work with only one osmus, then everything is simple here. It is necessary to rewind 2-4 m of fishing line (depending on the size of the coil), find the hole for the trimmer on the inside of the coil, insert one end of the fishing line there and start to wind the fishing line for the trimmer in the direction in the reverse direction of rotation of the coil at the trimmer. The inside of the coil is usually indicated with an arrow in which the side is to wind a fishing line for a trimmer. Having wiped a fishing line for a trimmer, we leave its small piece unnecessary to put it out. We fix this piece in a special groove located on the inner part of the coil and designed so that at the time of collecting the coil of the fishing line for a trimmer does not unwind. If there is no such groove, then you will have to hold a fishing line for a trimmer with a finger, so as not to let it unwind during the further collection of the coil. Next, we take the outer part of the coil and spread the outer piece of fishing line into the available hole, collect and put the coil back to the trimmer for the grass.

If the coil is designed to work with two antennae, then we do the following. On the inside of the coil, we look at how many grooves are available for winding fishing. There may be one or two of them. If the groove is one, then both antennae are wound on this one groove. If there are two grooves, then each antennae is wound in a groove. The coil with one groove should have a through hole in which a fishing line for a trimmer is threaded. We open 2-4 m of fishing line, we extend it through this hole so that on each side of the fishing line it sticks the same. And we will simultaneously wrap both the antennae of the fishing line in one direction, the reverse direction of rotation of the coil in the trimmer and coinciding with the direction indicated by the arrow available on the inner part of the coil. We leave a little fishing fishing line, we fix the resulting ends in special grooves, and if they are not, we hold with your fingers. We spread both ends into the available holes on the outer body of the coil. Collect the coil and fasten it to the trimmer.

In the presence of two grooves, a piece of fishing line 2-4 m long is folded in half, we insert the loop in the groove between two grooves at the bending site, and we wind both the ends of the fishing line each in its groove at the same time. Further actions are similar to the previous option.

There are also coils, in which a fishing line for a trimmer is threaded through a through hole on the inside. After that, the ends of the fishing line, without wrapping, spread completely through the holes on the outer body of the coil, collect the coil and begin to rotate the button that is usually pressed in order to release the fishing line for the trimmer while it is worn out. Rotate the button. inside the trimmer fishing line is wound itself. At the same time, it will not work to twist it in the “wrong” direction, since it can spin only in one direction. If you get used to it, then you can wrap a fishing line for a trimmer to such a reel without even taking it out. you just need to combine the through hole of the internal drum with holes on the outer body of the coil, and then pass the fishing line for the trimmer in them.

That’s all on this issue. Successful winding!

Remove the coil from a trimmer for grass

On small electric trimmers with the lower engine location (when it is located at the ground) at the coil, usually there are two keys on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line for the trimmer is directly wound. When analyzing, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a bent bar (on such trimmers there is no way to put a knife yet) you need to grab the coil body itself with one hand, and with the second hand you need to start turning counterclockwise the lamb available on it. It is he who attaches the coil to the bar trimmer for the grass. Having unscrewed the lambs, carefully remove the whole coil, trying not to lose the spring available inside.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers for grass, in addition to the fishing line, you can also install a knife) look for a hole under the coil, insert, for example, a screwdriver, we quietly rotate the coil until the screwdriver crawls deeper deeper. and the coil will be fixed. Now we twist the whole coil clockwise (since the thread is left) and remove it from the trimmer for the grass. Then we disassemble the coil. It can be collected using latches or twisted with a lamb. If the coil is on the latches, then we press on the sides on the base of the latches so that they bent and free one half of the coil body from the other. We just twist the lamb. There may also be a third type of connection of two halves of such a coil: with it you need to grab the lower part with one hand, and the top is the upper one, and start turning them in opposite directions. Disasseminating such a coil, you must also follow so that the spring available inside is not lost.

Trimmer coil for grass with one osmus

Many owners and experts note the simplicity of the operation and refueling of bobin with one mustache. Depending on the manufacturer, the length of the refueling fishing line can range from 2 to 5 meters. The end of the fishing line is inserted into the head in a special technological groove or hole, and the winding is carried out in the reverse work rotation of the bobbin side. On most coils on the outer side of the case there are marks in the form of arrows, which indicate the direction of the movement of the bobbin of the trimmer for the grass.

After winding, you need to leave the free end of 15-30 cm to strengthen the centrifugal force, which is determining when extracting a trimmer fishing line in automatic and semi-automatic reels. The left end is extended through the coil work hole and make the head assembly.

Tools

Features of a trimmer for grass Patriot Pt 3055

• In the production of the device, modern materials and assembly technologies were used.
• The latest anti.vibration system is provided.
• High performance is achieved due to the chrome engine with wear.resistant and clearly adjusted details.

• Simple and mobile control system. On the bicycle shape in the reach of the launch button and gas clamp, which allows you to carry out work with accurate calculation and mobile control.
• For lubrication of drives, a line of unique motor oils was developed.
• The simplicity of the assembly and use of the tool is designed for an ordinary person without special technical knowledge and work experience.
• Safe operation. The protective casing protects the operator’s hands from injuries.

How to assemble a gasoline trimmer for grass Patriot Pt 3055

• The handle of the main bar is installed and fixed and fixed so that the open part is located on the right side of the handle.
• The handle is made by bolts not to the end, but taking into account the subsequent adjustment.
• The control handle is installed by a gas trim.

• The fastening screw is twisted with a slight effort. Cable clips on the handle are attached.
• The shoulder belt is snapped by a carbine for a special mount on the main rod of the unit.
• To the lower part of the bar, at the base, the iron casing is screwed onto the protective case of the gearbox, and a plastic casing is attached on top to enhance protection.
• A protective flange is installed on the slotted gearbox with the coincidence of technical grooves on the gearbox with flange.
• A fixing rod or hexagon is inserted between the gearbox and the flange.
• The trimmer head is twisted to the stop, against the course of the time of time.
• A cutting knife is installed on a protective flange.
• A knife is pressed with a puck and twisted with a nut to the stops against the course of the clock.

If the knife is swept on one side, then it is turned over and use the second sharpened side.

• Both parts of the rod are connected using a fixing lever of the fastener system.
• Checking the correct assembly: the impossibility of opening without pressing on fixing fasteners.
• The additional mounting of the coupling of the connection is tightened to the stop. This gives an advantage when using the unit to perform various works: the lower rod is installed on fixed angles of 90 and 180 degrees.

Description of a model of a gasoline trimmer for grass Patriot Pt 3055

• Due to the high.quality design of the two.stroke engine and its upper location in the design, a low noise level is released up to 70 dB.
• Fuel tank made of transparent, resistant to aggressive environments.
• Semi.automatic fishing line.
• The width of the strip capture with a knife up to 220 mm.
• Cutting the excess length of the fishing line is carried out with a special knife in a protective casing.
• Air filter is multi.stage, captures large, medium and small fractions of suspended dust and solid particles.
• The rod is detachable, convenient for transportation and storage.

Winding fishing line on a trimmer for grass

Measured and accurate dismantling of a spray from the coil of braids for grass makes it possible to go directly to the winding of the fishing line. Design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today, there are several varieties of coils depending on the number of antennae antennae and refueling methods:

Trimmer coil for grass with one osmus

Many owners and experts note the simplicity of the operation and refueling of bobin with one mustache. Depending on the manufacturer, the length of the refueling fishing line can range from 2 to 5 meters. The end of the fishing line is inserted into the head in a special technological groove or hole, and the winding is carried out in the reverse work rotation of the bobbin side. On most coils on the outer side of the case there are marks in the form of arrows, which indicate the direction of the movement of the bobbin of the trimmer for the grass.

After winding, you need to leave the free end of 15-30 cm to strengthen the centrifugal force, which is determining when extracting a trimmer fishing line in automatic and semi-automatic reels. The left end is extended through the coil work hole and make the head assembly.

Trimmer head with two antennae

After extracting the spray from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but with a careless refueling in a paired groove, there are problems with operation. Due to the likelihood of weaving neighboring tools, a situation may arise when after the wear of the working antennae it is impossible to extract new.

Regardless of the number of streams for refueling, a fishing line is taken for a trimmer from 1 length.5 to 3 meters. The winding must be carried out in reverse rotation of the head to the side, since the winding in the direction of movement will lead to the fact that the fishing line for the trimmer will not be removed from the bobbin. After the fishing line for the trimmer is tucked into the coil of the trimmer for the grass, free ends (15-30 cm) we stretch into special holes. Next, collect the head in the reverse disassembly order and check the performance. Do not worry if the ends of the two antennae are very different in size, since when the trimmer for the grass is launched, the knife installed on protection will cut off the excess.

Trimmer head for grass with automatic line dressing

In some models presented on the market, a coil with an automatic winding mechanism is installed. It is enough to correct the owner and fix the ends in the head, and the winding operation will perform the tool itself when included in the operating mode. It is almost impossible to incorporate a fishing line for a trimmer to a trimmer for grass with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic head of the trimmer for grass include the simplicity of the line for refueling, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

Types of woods for a trimmer for grass

First of all, in order not to resort to frequent replacements, it is better to use a denser fishing line for a trimmer. The number of its species and manufacturers is simply amazing. The main parameter of the fishing line for a trimmer for grass is its diameter. He varies from 1.6 to 3.2 mm. The most common view is a 2-mm fishing line for a trimmer. However, its selection must be carried out depending on your type of trimmer for grass.

Distinguish several variants of the cross.line section. So, it can be round, square, in the form of an asterisk with sharp faces. The last option is the most effective. However, it is worthwhile only on powerful braids and at the same time you need to know how to fill the fishing line for a trimmer into a coil of a trimmer for grass. Therefore, we can conclude that the more powerful your lawn mower is, the more the fishing line for the trimmer should be thicker.

A process such as winding a fishing line on a trimmer for grass is not difficult, but has its own characteristics. First you need to choose the right fishing line for a trimmer, the diameter of which is registered in the device passport.

First, unscrew the coil lid. Be careful, since the thread can be both left and right. The left thread is necessary so that during operation the head of the braid for the grass does not spin.

Read the same

Bobbins of the trimmers, the motor of which is located near the ground, have a different fastening to the rotation axis, they have two buttons on the coil located at the edges that need to be squeezed, the rest of the thread is no different from the other cassettes.

The principle of proper winding of the fishing line is identical in all of the above

cases, because for example, we see the standard option with 2 antennae.

To remove the coil with a fishing line, you need to unscrew

, located in the center, a screw, but keep in mind that the thread is left there, because you will have to twist clockwise, it is specially made so that during operation it does not open under the influence of centrifugal force.

Further, using the screwdriver, to disassemble the head and pull out the coil, on which the fishing line for the trimmer is specifically wound. How to choose and wind a fishing line for a trimmer to a trimmer coil for grass. Than a fishing line for a trimmer on a trimmer, video from. The video shows in detail how to wind a fishing line for a trimmer to a trimmer coil for grass or motorcycle. Having measured the desired length and folding twice, it is necessary to season the fishing line for the trimmer to the coil, leading, ultimately, its ends opposite each other (for this there are special slots for fixation).

After that, you need to collect the head in the back, passing the ends of the cord in two corresponding holes.

If there are doubts or it is not completely clear how to charge a fishing line for a trimmer for a trimmer for grass we advise you to look at how to correctly wind the fishing line for a trimmer into a lawn mower. In this video clip, the instructor will thoroughly open a trimmer head in steps, measure the right amount of fishing line, usually from 2 to 4 meters, and demonstrate the assembly and installation for a trimmer for grass.

Magneto Design and a scheme of work

The transformation of rotation energy into a high.voltage discharge and the formation of a spark that ignites the fuel mixture. In the internal combustion engine, this detail is called Magneto, because in it alternating current is generated from the rotation of a constant magnetic rotor or anchor.

Magneto constructively consists of 2 windings: the highest and low voltage. The condenser with interrupter contacts are parallel to the latter. Whereas the conclusions of the winding of the highest voltage are connected to the candle and body. They are both wound on a core, between the poles of which a spinning magnet is installed, magnetized longitudinally.

https: // r-d1.info/2990-Kak-Snyat-Katushku-S-Trimmera-Shtil-2020-03-29.html https: // r-d1.info/2494-Kak-Snyat-Shpulyu-S-Trimmera-Patriot-2020-03-15.html https: // hitech-online.ru/Tehnika-Dlya-Sada/Trimmer/Remont-Katushki-Zazhiganiya.HTML

Remove the coil from a trimmer for grass

On small electric trimmers with the lower engine location (when it is located at the ground) at the coil, usually there are two buttons on the sides. Click on them and disconnect one half of the coil body from the 2nd, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which it is directly wound Lines for a trimmer

Carburetor of a trimmer for grass adjustment of the needle. When analyzing, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers for grass, without counting the fishing line, you can install a knife) look for a hole under the coil, insert, for example, a screwdriver, we quietly rotate the coil until the screwdriver crawls even deeper, and the coil will be fixed.

The structure of the inertial coils

Undoubtedly, in order to fix the coil, you need to represent its structure and the principle of operation. Without exception, all inertias gather in factory conditions from the same type of nodes, differing depending on the dimensions of the mechanism with their sizes. The main components are the following parts and details of the product below:

Coil for trimmerpatriotdl-1214. It is easy to season a fishing line for a trimmer!

Depending on the modification and purpose of the inertia, or as it is also called fishermen, it can be supplemented by a specific functionality inherent in a certain model.

How to disassemblekatushitrimerimer. Replacing the fishing line by the diet.

In this Vyda, I am how to disassemble a gasoline trimmer, as well as how to wrap it correctly.

Usually, the diameter that can mow young grass does not exceed 1.6 mm. I have on a similar trimmer how to remove a coil from a trimmer for grass, and the garden, meanwhile, overgrown. The thicker the thread, the more rough the grass it is able to overcome.

There are fishing lines with sharpened faces in the form of a sprocket or square, such an option is more adapted to mowing dry grass just due to the existing sharp faces, but it is more wear and tear and it is inferior in strength to the round cord.

How to remove and put a reel on a lawn mower!

To carry out this operation, it is aimed to turn off the network and turn over the work head upward. The upcoming course of action is depending on the design of the structure of the coil itself:

• In small trimmers with the lower location of the engine, click on the button located at the edges of the coil and remove its highest part from the head;
• On trimmers with a bent rod, clamp the coil of the coil with one hand, immediately turning counterclockwise located on the hooding of the lambs;
• In trimmers with a straight bar and a gearbox, insert the screwdriver into the hole located under the coil, and then turn the body of the coil counterclockwise.

How to replace, remove the spitter of the electric trimmerblackdecker GL716 electric trimmer

How to change, remove the mowing of the electric trimmerblackdecker GL716 DOCTION of the repair or substitution.

https: // cylinder.com.ua/blog/kak_namotat_lesku_na_katushku_trimmera https: // Instrument-tehnika.ru/kak-PRAVILNO-NAMOTY-SLE-NA-KATUSHKU-TRIMMERA/https: // kupihome.ru/Podklyuchenie/Remont-Katushki-Trimmera-Svoimi-Rukami-Kak-Snyat-Razobrat-Sobrat-I-Ustanovit.obratno.HTML

Trimmer for grass braid for Patriot Pt 555 Harse Overview Part 2 Formation of nozzles. Winding of fishing line on a reel

How to wind the cutting cord to the coil of motorcycles (trimmer for grass)

than 200 types of trimmers in one place at the lowest prices. Click and look

Now, having figured out and dismantling the coil, we actually continue the winding.

How to refuel a fishing line for a trimmer to a trimmer coil for grass. Detailed guide for working with a trimmer

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.capanal coils, the fishing line for a trimmer extends into the through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. the arrow of the arrow is exaggeratedly indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded here or hold the fingers of the free hand, spread into the through hole of the outer half of the bobin, the spool is locked and attached to the bar of the trimmer product.

The difference in the winding of the fishing line in the two-drummer coils is that the line of the fishing line 2-5 m long is in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound up who on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this process, you will seem long and quite labor-cost, but over time and experience, this problem will be solved significantly more frequent and easier.

The video below will clearly show how to fill the fishing line for the trimmer into the coil of the trimmer for the grass and correctly wrap it. this operation is not any difficulties and, with some patience, will certainly be crowned with a furro:

There is a type of coils in which the automatic mechanism performs winding without the help of others. from the user you will have to correctly season the fishing line for the trimmer. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are tied through the hole on the outer case, the bobbin is assembled, and when rotating the winding button for the trimmer, the snitches are wound without the help of others. It is unrealistic to make the winding erroneous in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

Number of blocks: 9 | General number of symbols: 10569 Kolya of the used donors: 4information for each donor:

The first option for a double bobbin

The thread is fixed on the rib rib. Rotation in the direction indicated by the arrow, the fishing line for the trimmer is wound on both disks. After winding, there were free ends

• Wrap the thread on the arrow indicating the direction of rotation so that the upper part remains at the top, the lower, respectively, below.
• Leave 15 cm from each edge.
• Find the grooves for the thread on the bobbin and insert the remaining segments into them.
• Collect the head of the trimmer for the grass so that the free sections of the fishing line fall into the holes of the working shaft.
• Insert the bobbin into the head, having previously returned the spring to its original place.
• Press the bobbin to the head, stretch the ends of the fishing line outside. Check how free sections of the cutting thread move. They must rotate the shaft freely, without jerking.
• Pour the lid on the bobbin. Check how the holes in the housing are combined. After all the grooves coincided, fix the lid.
• Install the head to its original place.

The power of the model

Light and compact household devices to combat grass on a section of less than 15 acres have a power up to 1 liter.With. Such an indicator is enough for a cottage, a small lawn.

Power within 1. 3 l.With. necessary to combat shrubs, thin branches. This is an indicator of industrial and universal units. They have a greater resource of work, weight, some models can create a high level of noise.

If you need to get rid of the young shoots of trees, the thick branches of the shrub use lawn mowers with a capacity of more than 3 liters.With. These are heavy devices for working with which large physical efforts are required. The advantages of such mowers are a large supply of fuel, separate gas station and oil, high productivity.

Model with a shoulder belt for ease of use

Up to one antenna coil

Wrap the coil with one antenna is very easy. In such designs, depending on the brand of a trimmer for grass, from two to five meters of the cord is located. The edge of the hair growth line in the coil should be clogged with a special hole or groove, and then during operation a thread is wound in a direction opposite to rotation of the coil.

Tips! To understand how to wind the thread, you need to look at the drum body. It usually put marks indicating the direction of movement of the drum during operation.

After winding the hair growth line, you need to leave a small piece (15-30 cm), screw it into the output of the coil and assemble the head.

To a coil with two antennas

In such coils, it is necessary to inspect the inside of the coil and determine the number of grooves for winding the cord provided for in it.

Important! If there is one gutter in the coil, then both antennas should be wound along the common groove, if two, then on separate paths.

For winding, you need to take a piece of hair from two to three meters long. For coils with one coil during operation, it is necessary to insert a fishing rod into the through hole, leve a mustache, leve and wind it in a direction in the direction opposite to its rotation. If there are slots for locking, they need to tie the ends of the cord, then drag them into a socket, then close the coil and put it in place.

For coils with two grooves, the difference is that the length of the line should be folded in half. Then it is necessary to load the middle of the bend into the groove between the grooves, then wrap each piece of the hairpin along its path, fix the antennas and collect the coil, as well as the coil of the same path.

Automatic trimmer head

For self.consuming heads, it is quite easy to start and pinch the edges of the line, and the tool will turn on when turning on. It is impossible to make a mistake here, because the coil itself recognizes how the antennas should be located.

The note! The advantages of trimmers with such a head include the convenience of laying the cord, and the disadvantages include the high cost and complexity of repair.

Hazel nuts are varieties and can be replaced by another material

A trimmer cord for grass can be a different diameter (from 1.2 to 4 mm), and you need to choose it depending on which vegetation you want to cut. The thicker the hair, the rougher the grass that they can process. Experienced users recommend installing a universal fishing line for a trimmer 2 mm thick.

The shape of the hairline can be round (for juicy grass) or with sharp edges in the shape of a square or asterisk (for mowing dry grass). The second type is less durable and wear out faster than a round cord.

One of the popular questions about the work of a trimmer for grass is whether it is possible to replace a special cord for mowers with other materials, such as metal or steel cables and cords, wire, etc. D. It is not recommended, because the trimmer for the grass turns them into dangerous equipment. During mowing, pieces of wire or metal will constantly burst and fly off in different directions, which can lead to an employee’s injury. And if you accidentally touch their limbs during work, a serious injury is guaranteed.

For trimmers who are interested in using a fishing line for a trimmer of hair, we answer. This is permitted, but it will burst out and wear out much faster, which will require frequent replacement.

Tips! The scaffold is well suited for collecting grass near the fence or wire mesh. Instead of spending an expensive three-dimensional cord, you can charge a large caliber (2-3 mm) gear, which is much cheaper.

Replacing the hairline on the disk

Depending on the type of vegetation that covers the garden (lawn) and requires removal, the hair turns into a disc. This is necessary because the cord is used only for herbs of low altitude, and if you need to mow tall trees, shoots of trees or shrubs, it is better to use metal or plastic knives instead of threads. Their correct installation is very simple, the detailed process is usually described in the user guide and is similar to trimmers for grass of different brands, whether Al-Co, Oleo-Mac, Patriot or other brand equipment. To change the fishing line for a trimmer on knives, you need:

• Block the shaft and remove the coil by turning it clockwise;
• put a knife on the sleeve;
• Insert a stoned cap and tighten the nut counterclockwise, then tighten it with a wrench.

You can read in detail how to replace the coil with a disk in the device operating manual.

Solving possible hair problems

Most problems of the hairline are similar to various trimmers and are solved similarly.

Rupture

• the presence of grass of solid objects in the mowing: branches, stones, etc. D., contact with which the thread cuts off;
• mow grass next to the fence, and if it read out, the hair grid breaks even faster;
• Low quality cord. It is necessary to replace new reliable consumables;
• wear of the exhaust openings in the head of the lawn mower, due to which the hair fishing line for a trimmer breaks away from friction around the sharp edges of the bushings. Replacing details with a new.

High flow rate

Typically, a fishing line for a trimmer of hair ends very quickly if you constantly push a semi.automatic coil to the ground or press it tightly to the surface. In this case, the head is unlocked, the cord is lengthened, and the knife is cut off. The second option. Fast line consumption. A trimmer for grass with an automatic coil is not used properly. If the lawn mower regularly reduces the engine speed, the cord is constantly lengthened and cut, and as a result it is quickly consumed.

The line does not hold

If the coil of the semi.automatic type of spring weakens, the hair does not hold or unwind during operation. The cord is lengthened, cut off with a knife, as a result, the equipment owner notices that the thread quickly ends.

Tips! To check the tool, you need to remove the protective cover and start the engine. If the fishing line for a trimmer of hair growth expands, this means that the spring should be replaced by a new.

The technical properties of the cord and the selection of diameter by the power of the trimmer for grass

If you take the packaging of the fishing line in your hands, then only two main parameters are indicated on it. this is the total length and cross section. Instructions on how to choose a fishing line for a trimmer for a trimmer for grass is not attached, so you have to find out from specialists. Finding a good specialist is not so simple, especially since every year not only new fishing lines, but also coils are produced every year.

Read does not enter the gas carburetor of a trimmer for grass

The first thing to solve is the diameter, thickness or cross section of the cord. All this is one parameter characterizing the performance of work by trimmers, benzocouses, motorcycles and travo.shirts. What sections to buy a fishing line for a trimmer for your trimmer for grass? In order not to make a mistake, you should take with you a segment of the old cord, and provide it to the seller. Based on the segment you provided, the seller will give a similar cross section the cord.

This option is certainly reliable, but it is impossible to call it correct. Why? After all, the choice of fishing line depends not only on the head used, but also on the power of the tool used. To begin with, it is recommended to solve what diameter the fishing line for the trimmer can be used on trimmers and benzocoses, depending on their power parameters:

• Electric trimmers for grass with power indicator up to 500 W. cords with a cross section of up to 1.6 mm are used.Such tools are designed to cut young grass in personalities
• Gasoline and electrical units with power indicators from 500 to 1000 W. involve the use of cords with a thickness of 2 to 2.4 mm.Such units with consumables are used to prick thin and thick grass, as well as weeds. In trimmers for grass up to 1 kW, you can install a fishing line for a trimmer with a diameter of 1-1.6 mm, but at the same time it will be quickly wear out
• Trammers for grass and lawn mowers with power indicators over 1 kW. allow the use of the cord with a thickness of 2.4 to 3.3 mm.Such fishing line can cut thick and dried stems, as well as thick thickets. If the consumable material with a thickness of more than 3 mm does not cope with the task of cutting grass, then metal disks with blades, teeth and knives are used

It is interesting!Manufacturers produce a trimmer fishing line for a trimmer with a diameter of more than 3.3 mm, only it is extremely rare, and exclusively on powerful gasoline units.