Is it possible to cut interior doors. The algorithm of actions

Sprinkling the door leaf in height (shortening). The cutting of the interior door is it possible to file an interior door with glass

Let’s start with the fact that any door block consists of two parts. the so.called “box” (louds) and door leaf. The box “tightly” is placed in the opening. From the inside of the box, a canvas opens, which can be glazed or continuous (deaf). Boxes are with a threshold and without a threshold. This affects the overall size of the block. The doors differ in action (opening-opening) in “”.The standard dimensions of the door blocks assembly with the threshold depending on the thickness of the racks: 650 × 2050 mm (660 × 2060) for san.nodes: 750 × 2050 mm (760 × 2060) for the kitchen: 850 × 2050 mm (860 × 2050) for residential premises, etc.D. Many varieties of doors are known. Among the wooden doors, a frame structure is most often found, and a board, plywood, wood.fiber slab, glass are used as an internal canvas. Recently, doors with laminated coatings are increasingly applied, including imitating the texture of natural wood and so to save money I would advise to buy these doors. Such doors can be redone in almost any size.

You need to start with the measurements of the opening where the block will be installed. If at the moment the opening is busy with an old door block, then in order to remove the exact dimensions, it is necessary to remove the platband that is nailed along the edge. Then we measure the width from the brick to the brick (the outer size of the box should be less than the size of the opening by 2-5 cm), measure the height from the finished floor to the jumper-beam (the outer size of the box should be 1 cm at least less than the opening). But it happens like this, and in private houses is often a lot, that the finished opening does not fit in any way and it is simply impossible to expand it. In this case, it is necessary to adjust the door leaf to fit by reducing size.

This is not done as difficult as it might seem at first glance. To do this, you must have a small arsenal of the power tool:

Thanks to this, you can adjust the canvases of standard sizes to smaller, not standard. Which makes it possible to fill in any openings. I think that the doors from the array (completely wooden) can also be tried to redo it within the rational.

Next, I will tell you how to change the door block without removing the old box (loud) t.to. There are cases that it is simply impossible to dismantle, because a whole opening can collapse due to the specifics of the construction mainly-this applies to old private houses, less often the old building of apartments. Of course, you can strengthen the controversial part of the opening, before dismantling, profile, but this is additional work for you, costs and of course unsafe.

We start with measurements. We measure the internal size of the old box in width: let’s say 1070 mm minus 30-40 mm for the exact installation of a new box, if not the level is old. In height, the internal size of the box from the top to the floor: let’s say 2000 mm minus 20 mm. If there is a threshold, then we cut it out and remove T.to. We don’t need him. We get the external size of the new. 1980 × 1030 mm, which we will put.

The door block for this size of the opening (1980 × 1030 mm) should be one and a half, t.e. one door is larger than the width and the other is smaller. For example, 600 mm and 380 mm-this is the size of the paintings in the width taking into account the thickness of the two racks of the box and the gap between the doors-this is 4-6 mm, as well as 30-50 mm gap for mounting foam. This size may vary depending on the thickness of the inserted box. And the height of the doors is 1930 mm.

How to reduce the door leafs I already wrote above.

As you can see the old box (loud) is not visible. On the inside, a new standard (100 mm) box, as a rule, does not overlap the old width. Therefore, it is necessary to increase the width of the new box around the perimeter with the help of a premature expansion bar, which is sold in any door salon. I usually use this. Glorifier bar (wood.fiber slab) universal. Dimensions: length: 2070 mm. Width: 120 mm.Thickness: 10 mm.

When after installation the mounting foam dries (preferably the next day) and the performed painting work, on both sides, block A is filled with cash. Then, in appearance, no one will guarantee no one will think that there were once old doors.

There are also openings not standard sizes, for example, the width is not enough for two a hollow or one and a half door, and for a single.sidedly large. In such cases, you can make a doorbell, t.e. folding door.

And yet, it happens that the standard door is 900 mm, it does not conveniently open in a narrow corridor. This is not difficult to do. ✓ take the door 900 mm wide, measure 600 mm (if less, it will not be convenient to pass). ✓ Khdosovka mode, but with such a calculation that the canvas does not go out onto the flight, those. cut one side of the door, turn over. the other mode is already on the flight. In general we do with one door, two doors. Since the doors inside are hollow, it is necessary to insert 27 × 27 mm with dimensions (27 × 40 mm, 27 × 45 mm) on the length of the PVA glue glue.

But 27 mm for doors 35 mm thick, the size remains unchanged. Otherwise you do not insert the bar if it is 30 × 40 mm in size. Then, when the glue dries somewhere after 12 hours at an air temperature of 20 ° C, you need to slightly pass the end and stick the decor (edge) to the color of the door. With a hot iron we press the edge to the end of the doors, cut and clean. When the canvases are ready, we connect them with each other using awnings. We just divided one door in width. 900 mm by 600 mm and 297 mm.

And what to do if the door block with a reduced door of 600 mm and 297 mm is not enough to fill the opening. Then you just need to select the standard door size and independently made half from an additional bought deaf or glazed canvas. With the latter it will be a little more difficult than t.to. It will be necessary to make two cuts due to glass. Deaf is easier.

where/how to cut the door leaf carefully?

You will have to make several approaches, while gradually deepening into the canvas. But do not forget that this method is more reliable and it will be easier for you to avoid irreparable errors. Experiment, try to achieve everything yourself, but do not forget that your actions should be carried out within a reasonable.

Few of the masters know exactly how to shorten the door, since this requires certain skills, and, of course, experience. After all, damaging the door is a minute business, and fixing is a complex and tedious process. Of course, the most ideal option is to turn to professionals who have the necessary knowledge and tools for this “operation”. Today you can get confused in the variety of companies that offer these services, and even more so to understand which of them is the best and profitable option for you. But you should not despair, you just need to know a few rules:

Do not contact a company that recently announced itself, and in the information writes that there has been existing in the market for decades. In this case, shortening of interior doors may end with the purchase of new.
If you decide to save, do not order private companies, it is better to use state proposals for repair. So you will save a certain amount of money, and you will rejoice at the result.
In order to find an inexpensive company, first you need to compare for the offered services. After that, you can safely order masters.
As soon as the master crossed the threshold of your home, once again check the price of his services. If they are higher, you can immediately call his company, and clarify the terms of the transaction again.

What will be needed for trimming the interior door in height?

Shorting the canvas at home is easy to electric jigsaw or circular saw. But to get a neat and straight cut, auxiliary tools will be required:

clamps that will help to fix the canvas and guide bars;
ruler and square for marking;
A sharp knife for working with an veneered door;
chomic tape for a canvas made of wood.fiber plate;
sandpaper.

To protect the decorative covering of the door from cracking along the cutting edge, you can use painting tape. If necessary, you can do without it.

Instructions how and what tool can be cut in height an interior door

During the repair, sometimes there is a change in the floor level (tile laying, filling the screed or self.leveling coating, etc. P.). After that, you have to cut the interior door in height to ensure its free move when opening and closing. The same operation has to be carried out when replacing if the new door is very large and does not fit the box. When installing a new frame, it may also be that the size of the opening does not comply with the standard of the product.

In what cases it is necessary to do this

If there are difficulties that do not allow to freely open the doors. this is an occasion to cut it. This happens in some cases:

after laying flooring;
after using a self.leveling coating;
In the case of deformation (when the tree is sagging or swelled).

The above factors are the most common indications for this procedure.

Instructions for independent work

Before carrying out the work, remove the canvas from the loops and prepare, removing the pens and other accessories from it. The door is cut on a workbench, but in the absence of its absence, a large stable table is suitable.

If the canvas from the array must be adjusted to the opening due to sagging or lifting the floor, then it is best to do the door trim from below. Remove 2 standards of height: on the loop and in the narthex. Merki transfer to the canvas, putting down new dimensions from the upper edge. Through 2 points draw a straight line for a trimmer. To do this, it is advisable to use a long ruler and a square to control the right angles between the edges.

Attach the guide rail by the applied markup. When using a power tool, it is better to use a metal strip or ruler. If you cut the door with a hand hacksaw on wood, guides from even racks are suitable. Press the template to the canvas with clamps above the marking.

To save a layer of varnish and veneer on a polished door, treat it with a corner grinder. The disk of the tool will leave the cut with even edges, which cannot be made with a saw. Take a corner grinder along the guide bar. Before processing on the mowing fishing line, glue the tape, and transfer the straight line to its surface.

If there is no corner grinder, the varnish coating on the removed part is removed with an sandpaper, and the veneer is cut out with a sharp knife on both planes of the canvas and on its only parts. After that, the door can be sawn down along the guide.

Remove the clamps, process the cuts of the cut with sandpaper. You need to glue the brown tape on the veneered door, choosing its shade to the veneer. If the massive canvas is painted, cover the cut with paint or varnish. Hang the door leaf on the frame, eliminate distortions and attach the removed accessories.

In the same sequence, work is performed when replacing the canvas: the standard dimensions of the new product can be changed in height and width. When performing work, you need to consider what the product is assembled from.

Instructions for independent work

Before carrying out the work, remove the canvas from the loops and prepare, removing pens and other accessories from it. The door is cut on a workbench, but in the absence of its absence, a large stable table is suitable.

Tips for professionals

A canvas from an array or wood.fiber plate can be trimmed from below if it does not have a philanic or their imitation. In the presence of a symmetric decor, it is better to cut off on both sides, dividing the value of the cut part by 2. These measurements are laid from each edge, without violating the symmetry of verity and the lower philanthone. The same is done if you need to reduce the standard width of the door leaf.

Frame hollow doors cannot be shortened too much. The product consists of wooden bars having a limited thickness. When performing work, you need to leave at least 1-1.5 cm of the frame bar inside the canvas. You can shorten the door, as indicated for design with phylenes. from above and below.

Read checking the battery of an electrical screwdriver multimeter video

When you try to install a standard door in a small opening, the chasing materials of the frame are shortened by the standards and fixed in the opening. The sizes of the sash will have to be adjusted according to the technology described above.

The canvas from the array sometimes swells due to excess humidity and does not enter the frame well. You can eliminate such a problem with a shirt or grinder (manual milling). Remove the canvas, put on a workbench and process its edge with a cutting tool, removing several millimeters of the chips from the right side. Hang the door and try its move. If the problem is not fixed, repeat the processing.

To get an even section of the array when using a circular saw, a disc with a large number of small teeth will be required. But even under this condition, it will not be possible to cut out the veneered product qualitatively. For a canvas made of wood.fiber plate, it is better to prefer an electrician, and perform the work in compliance with the layer of veneer of the rules (gluing tape, cutting veneer).

If it is possible to use a hand cutter, then you only have to choose it for work. The tool will perform even and clear sawing, and the cutting line for the cutting trimmer will not have to be processed additionally on a massive product, or on a wood.fiber plate or a frame model.

For proper gluing the bromic tape, use PVA glue and iron. The adhesive layer needs to be applied to the saws of the canvases, let it dry. Apply the tape to the edge of the door and iron through the paper with a hot iron. After cooling the excess, cut the tape with a sharp knife, and slightly wipe the edges with sandpaper.

Are all wooden doors suitable for trimming

This issue is no less relevant than the work technology. All materials based on a tree can be cut. over, this must be done if the opening is difficult to open, and for this it is necessary to make efforts. Among the most used woody rocks are distinguished:

Natural material serves the owners perfectly and is easily cut using the aforementioned technologies.

Small.sized apartments do not have enough space for furniture. The owners of these apartments are faced with some difficulties in determining the place to place the clothing cabinet. In it you can also store various.

The situation when the legs are staggering at the table, occurs in almost every house, apartment or office. Many are in a hurry to buy new furniture or by “half measures”, that is, they put something to ensure balance. But.

Sometimes people have a need to ennoble the interior door with their own hands. Typically, such ideas come to mind after a cosmetic repair, during which the style of decoration of the room has changed, and therefore other elements.

The most convenient place in the house or apartment for storing things is a dressing room. In this case, everything is in one place and you do not need to rush around the cabinets to find clothes.

Until recently, the hallway under a tree was considered the height of chic and sophistication, today it can be found both in a country house and in a city apartment. Wood. warm, tactfully pleasant material, harmoniously.

The secrets of the master

alteration of interior doors and not only.

In the course of work in a particular area, any master with time has his own invaluable experience. I am also not an exception, over the years I have accumulated some knowledge, additional skills, if you like, tricks in my craft.

It can come in handy. Picture-Link to determine the direction of movement of the door leaf.

Many people ask: “Where it is better to open the doors to the corridor or to the room?””

According to the rules of construction. from a smaller room to more, but in general it is necessary to put it so that, first of all, it is convenient for residents. To determine the direction of movement of door slotted loops, see the photo. On which side the slot between the halves (cards) of the canopy in a closed position is left or right, then this is the canopy. There are still insoluble awnings, but they are universal and therefore they can be rotated. So everything is simple.

I tried to trim the door to the door in width, t.e. made from seventy (700 mm) sixties (600 mm) in a new way. I liked it because it is fast and good. To quickly reduce the door leaf, I use this is not a complicated device made using a conventional angular grinding machine (corner grinder) and a detachment of wood with a diameter of 125 mm no more.to. Sawed should be half less than the thickness of the door, because when the saw exits its teeth, the edge of the laminated wood.fiber slab is torn and it turns out not a clean and not beautiful cut. In order to still saw off, you just need to do a drink on both sides. Watch the video and photo below.

In the video and in the photo you can clearly see the process of cutting the door leaf in width.

If you did not understand something, then you can contact me in the “Contacts” section. I will answer any of your questions.

Pruning of an interior door from an array of wood, or “for a husband for half an hour!”

February 23 is a holiday and a day off! It is necessary to lose my conscience completely in order to force a man to do anything around the house on such a day. And then she also broke her head, what to give-the keys to Paradise gave, the world threw at his feet many times, socks and gels for the shower I give without holidays, and in order to truly understand his internal suffering, no drink will be enough. I thought, I thought, and finally came up with. The fact is that I bought a new carpet in a bedroom, which has more pile than the previous one, and the interior door rested on this carpet and did not open completely. The door had to be shortened from below 1 cm, but I could not interrogate to do it in any way. So the idea of the gift of a master class in pruning the interior door came to me)) The main thing is the presence of an idea and 30 minutes to implement it!

Maybe someone will decide that this is too gorgeous a gift, but I liked my idea. Firstly, there is no money for such a gift at all-I will do it for free, and secondly, I will finally solve the problem that I could not solve for several months, and then no one will reproach me that I constantly pester with any bullshit.

At my master class, everything that I asked for the “gifted lucky man” about is to stand nearby, hold the door when removing the loops and help put it on the table.

The course of work

With the help of a screwdriver, I unscrewed the screws and we took off the door from the loops.

After removal, the door was laid on the spread table, taking into account the edge of the door hanging. the edge that is shortened, and we shorten the door leaf from below. So as not to scratch the table, Plaid and the oilcloth put under the door.

Then I wanted to make a marking, but here the “gifted lucky man” was indignant and with the words: “I myself can hold a pencil in my hands,” with the help of a ruler I outlined a fishing line for a trimmer of the cut, retreating from the edge of 1 cm. Then, turning the door, turning the marking and on the other side of the door.

So that the edges of the door do not crack along the edge of the saw, often recommend using painting tape, but we did without it. Then, with the help of an electric rhuban, I shortened the door leaf to the size I needed.

Electric russian.

Everything is smooth and neatly removed. It remains to paint the end.

Then processed the cut end of the water stain. To accelerate the process, the place of painting dried with her usual hair hair dryer and covered it with varnish.

We hang the finished door leaf on the hinges.

All is ready! The door is easily open and closes. It took about 30 minutes all the work, so I can safely name this master class “For my husband for half an hour!””.

The gift was accepted with a bang, and, as they say, they do not look in the giving horse in the teeth. Everyone was satisfied, though she noticed that the “gifted lucky man” had a slight thoughtfulness in her gaze. Well, so soon March 8th-there is something to think about. :)))

Completion of door handling

Set the door to the goat support and cut the line you marched. If you have a door with a built.in window or several small windows and you need to remove more than 5 mm, then you need to cut off half of this thickness on each side, otherwise the door will be asymmetric. So that the door can close evenly, if necessary, it is possible to make a bevel point directed down with a base with a base of 1.5 mm and tilt towards the inside of the door.

The master will help you to saw off below

The current service centers that repair the interior doors, as well as their maintenance, offer a lot of various services, among which there is usually such a service as pruning the door in height, which causes many townsfolk sincere bewilderment. Indeed, whether the door trim is needed at all, if it is much easier to measure the doorway and, in accordance with these dimensions, purchase the finished design in the store or place an order for its manufacture in some workshop. The answer is simple. the need to shorten the door from below is often the only option for saving the family budget, because the implementation of such a procedure is much cheaper than buying a new door leaf. There may be several reasons for trimming, but the main one is associated with the implementation of repair work, as a result of which the floor level rises. And this does not happen so rarely.

Each person who sets new doors in his house hopes for their longest period of operation. It is logical that for this purpose high.quality and reliable door structures are purchased from respected manufacturers or ordered from professional masters. After all, a similar approach gives confidence that the repair of such a purchase will be needed very soon. This is exactly what the vast majority of cases happen. But people rarely take into account the state of their flooring when choosing doors. And then another repair happens, and the owner of the apartment is decided on a new parquet or laminate, as a result of which the floor level rises. Indeed, in order to organize a system of warm floors, put a parquet board or mount a laminate, it is necessary to lay a layer of soundproofing and protection against moisture. And if the base is not perfectly even, then also leve it with a layer of a new screed. As a result, the perfectly mounted door leaf begins to touch the flooring. Solving this problem is quite simple, you just need to file the door from below, processing it after that with a special protective composition, and it will again open and close. over, its functionality will not suffer at all. You can go otherwise. buy and re.install door structures, but this option is very highly high, so it does not in demand. The first option is much cheaper, although it is unlikely that it will be possible to bring it to life on your own. After all, few people know firsthand how to cut the interior door in order to prevent possible damage and damage to its appearance.

This is where the services of professional masters performing the installation and repair of doors will come in handy. Qualified carpenters with solid experience with interior structures usually use the following tools to reduce the height of the canvas: circular saws and manual mills. The holder of the circular saw can shorten the interior door without resorting to dismantling it. Before such an operation, the carpenter carefully measures the estimated cutting size, based on these data and the circular saw disc is installed. The quality of the cut will depend on the even floor covering, since the tool passes along the floor surface. Next, the master performs the horizontal cut, cutting off the lower part of the canvas over the entire width. A similar operation should be performed before laying a parquet board/laminate, since otherwise it is unlikely that it is possible to shorten the door from below without removing it from the loops.

It is much more convenient to use a hand mill for this purpose, although such an operation is more time.consuming. In this case, the door leaf is dismantled, after which it is attached on a flat surface with a clamp. A guide for the milling force is a wooden block, which is set by a master at the required level. In this case, the cutter should remove the wood at a strictly set distance. As you can see, even the presence of such a tool does not guarantee a quality work if a beginner is engaged in it. With a milling mill, the door trimming process lasts more than with a circular saw, because the carpenter will be forced to make more than one pass before the tool removes the required part of the canvas. However, this option is more reliable: the edges of the cut are perfectly even, as a result of which the appearance of the door does not deteriorate at all. In other cases, the need for such repair work may occur due to unprofessional installation of door structures. Due to the installation errors made, you have to cut the interior door shortly after installation, and only attracting an experienced specialist will allow you to protect yourself from such problems.

Gluing veneer to the processed door

Despite the apparent simplicity, this stage has its subtleties. Is it possible to attach a veneer or furniture tape without their knowledge? It is possible, but at the same time it is impossible to guarantee the quality and durability of such work.

Before gluing, necessarily degrease the surface. After that, a PVA layer for a tree is applied to the door. Wait for its complete drying. Fasten the veneer or tape on fresh glue is not recommended.

Prepared for gluing the door

Next, a sheet of veneer or tape is applied to the cut. Through a sheet of paper over the entire surface, it is carried out with a hot iron (the regulator is exhibited in the middle position). The protruding glue is removed along the way and ensure that the buckthorn does not appear on the veneer.

Important remark: in the case of using a new sheet, it must be cut so that the edges perform a little. You can cut them after final drying.

How to cut the doors from PVC or wood-based stove at home, if your size does not comply with the standard?

When repairing in individual buildings of the old building, where there are very low ceilings and not quite standard doorways, the question often arises of changing the size of the purchased standard door. The same questions can arise when the floors are arranged and repair, as well as after laying a new floor carpet coating.

Most modern stores now have the opportunity to change the size of the doors existing for sale, as they take into account customer requests and organized small carpentry workshops directly in their stores, or collaborate with firms that can provide this type of service.

But there is no way to find people who will take up changes in the standard door. And sometimes it is necessary to fit the door already purchased and delivered home. And transport it for shortening is inappropriate. Therefore, the issue of changing the sizes of doors at home remains relevant.

And believe me, it is possible to solve this issue independently, practical without any costs, except for its ingenuity and your own work.

How to cut the door

To change the door standards, first of all, you need to know the structural features of your door.

The designs of interior doors according to the manufacturing method are divided into shield and framework (phylene, strapping).

The shield doors consist: of the frame. a frame made of wooden bars (slats), a sheathing made on both sides, from sheet material, and filling in the form of paper hundreds, polyurethane or spiral chips. Shield doors can be deaf and partially glazed.

Framework doors consist: of the strapping (main bars), mediums (bars dividing the door leaf into pieces) and filler (Philina). Glass, wood.fiber and wood boards are used as a phylenka.

If you shorten the doors yourself, at home, it will not be difficult, then changing the door width is much more difficult, but it is also quite possible.

But let’s dwell on the short time. Before starting work, you must definitely remember the old Russian proverb: “Measure seven times and cut it once once.”Must be carefully calculated, prepare the necessary tools, the necessary materials.

hacksaw with small teeth,
Hand disk saw an electric or grinding corner machine (in the common people. “corner grinder”),
plane,
carpentry glue and wooden bars of suitable size. We use bars. 30×30 mm.

If we use the “corner grinder”, then for the work of work the cutting circle for metal is best suited. When working, there will be a lot of smoke and burning from it, but it will allow you to get drunk without relaxation and cracks in such materials as wood.fiber plate and wood.fiber plate.

If we make a shortage with a manual disk saw, then we take a disk with small teeth for work and as much as possible-80-112 pcs.

We will make the measurements we need and proceed to the very process of the shortening.

We mark the canvas

And if, we make a cut with a disc saw, then from the back we attach the board to the door in order to get an even, without a burr, drank it.

If we carry out the work using a “angular grinder”, then it is necessary to make a wooden structure on both sides of the door. Putting and fixing the boards on both sides. This design will serve to stop in it circle.

We make a shortage of the door

The lower section of the door leaf consists of a continuous wooden bar, taking into account the possibility of a shortening. But usually, its width is not enough. Therefore, we will come in handy, we prepared by us a bar of 30×30 mm., to close the cavity that opened after a shortening. Using a hacksaw, we prepare the block we need along the length, adjust the thickness of the shirt in thickness, and mount it on glue.

Cutting the door leaf of the Philnah door or shield door with glass inserts, it is necessary to remember the proportions of all its components (the ratio of the size of all parts and the whole). Having greatly changed the size of the lower part of the door, we can break its harmony. And the door itself and the entire interior will be completely different.

Therefore, we need to consider the possibility of trimming the canvas from both sides and from the top and from the bottom.

In the same way as described above, it is possible to change the size of the door in width.

But I would not recommend this, because the pruning, with the help of the tool we have, for a length of 2 meters, will be very problematic and all the resulting flaws will be very noticeable. Such work is best done on special machines and entrust it to professionals.

How To Cut & Resize A Hollow Interior Door

And we can, if necessary, try to change the size of the doorway.

Cutting Off Doors While Hanging??? with a Standard Circular Saw???

In general, we see that it is quite realistic to change the size of the door, if necessary, at home.

Get to work, you will definitely succeed.

Pruning of an interior door from an array of wood, or “for a husband for half an hour!”

At my master class, everything that I asked for the “gifted lucky man” about is to stand nearby, hold the door when removing the loops and help put it on the table.

Materials and tools

With the help of a screwdriver, I unscrewed the screws and we took off the door from the loops.

Electric russian.

Everything is smooth and neatly removed. It remains to paint the end.

Then processed the cut end of the water stain. To accelerate the process, the place of painting dried with her usual hair hair dryer and covered it with varnish.

We hang the finished door leaf on the hinges.

All is ready! The door is easily open and closes. It took about 30 minutes all the work, so I can safely name this master class “For my husband for half an hour!””.

Sources:

https://rt82.ru/natural/podpilivanie-dvernogo-polotna-po-vysote-ukorachivanie/
https://kotelsibir.ru/dveri/podrezat-dver.html
https://veka-slide.ru/dveri/kak-obrezat-dvernoe-polotno.html
https://aqua45.ru/dver/podrezat.html
https://dtm-spb.ru/stati/kak-obrezat-mezhkomnatnuyu-dver/
https://climairpatrol.ru/dveri/kak-podrezat-derevyannuyu-dver.html
https://papa-carlo.su/materialy/mdf/kak-ukorotit-dvernoe-polotno-iz-mdf.html
https://vgtkraska24.ru/dveri/mozhno-li-podpilit-mezhkomnatnuju-dver.html
https://7dach.ru/OlgaDa/obrezka-mezhkomnatnoy-dveri-iz-massiva-dereva-ili-za-muzha-na-polchasa-248098.html

Articles actions, doors, interior, possible