Kick Starter for one -time tractor with your own hands. Starter device

Installation of an electric steamer on a single.based Neva tractor with your own hands. Starter for one.time tractor: device, repair and maintenance recommendations

Motobobes do not constitute complex designs, but at the same time they contain certain features. For example, when using this device, two starters work simultaneously: the main and additional. In addition, the role of assistants can also play spring and electrical options. The latter are considered the most popular, since they can be installed without problems on motoblocks and carry out repair work. A distinctive feature of such starters also consists in the fact that they are unpretentious, therefore they do not require too careful use.

In the process of choice, most users usually prefer a manual starter. It has a huge number of advantages in comparison with electric and other options. Such a device includes the following details:

It is the manual starter that is most popular, since during operation such devices often fail, so they have to be repaired, but just manual options are extremely easy to repair. Consider how the process of restoring the performance of the starter looks like.

• Before starting the repair, you need to find a scheme from the manufacturer to understand the features of the location of all parts. In addition, it will be useful to understand the instructions.
• You need to prepare the key with which you can unscrew and remove the nuts.
• Before shooting a starter, it is best to take a few photos. This will help restore everything if you forget the location of certain details.
• Unscrew the puck that is located in the center of the drum.
• Find damaged elements and conduct their replacement.

Thus, the repair of a hand starter does not take too much time, so this variety is very popular. In the process of restoring the performance of the starter for the walk.behind tractor, the main thing is to pay attention to any details, even the smallest.

For a walk.behind tractor, you can also install other types of starters. Among the most popular and demanded in the market, several types of.

• Spring, which are considered the simplest both in use and installation. In order to start such equipment, you will just need to move the motor block handle. The unit includes a semi.automatic spring, which provides the necessary acceleration of the power plant. In order to replace the manual version with a mechanical version, it will take no more than two hours.

• Electric ones that work from built.in battery. It is the last detail that determines the level of power of the device and its autonomous operation period. It should be noted that such starters can not be installed on all motoblocks. Only some models are able to work with electricity, so before choosing you must definitely study the features of your unit.

In the process of choosing any starter, it should be understood that in the first year of work they are almost all the same. If the company is conscientious, then each device will fully fulfill the functions assigned to it, but after a year the situation changes. In order for the device to work as best and longer as possible, you need to constantly care for it, lubricate and replace the failed parts. Only in this case, the starter can boast of high performance and durability.

Self.repair of the starter. algorithm in details

Over time, a hand starter of the used motoblock often fails. In this case, the mechanism will need to be dismantled for repair or complete replacement of broken elements. In order to prevent errors when removing the starter, you will need to use the scheme from the manufacturer of the walk.behind tractor.

Repair of the starter starter is carried out in the following sequence:

• There is a puck in the central part of the starting drum. It will need to be unscrewed in the first place;
• Gently disconnecting the cover of the starter case, after which it is necessary to inspect all the spare parts of the mechanism not the subject of breakdowns;
• Motoboblock kickstarter consists of a mass of small details. it is very important not to lose them during the repair. To do this, all elements should be laid out on a piece of an old newspaper or fabric;
• Most often, the repair of the starter implies the replacement of worn parts. over, the length and width of new spare parts is of great importance. If they are too large, then the hull cover will not close, and the one.axine tractor will not start;
• Very often a large spring is subject to replacement in the design of the starter. There are special hooks at its ends, with which the part clings to other elements of the mechanism. When replacing the spring, you should be extremely careful so as not to damage the hooks.

Installation of the starter on a single tractor

There are various designs of starters:

The most common is a manual starter to a walk.behind tractor, t. to. This device is very easy to put on a single tractor, and its repair is easy to perform on its own. If such a device is operated correctly, then its durability is several years.

Consider which elements the starter for a walk.behind tractor consists of:

• a body that has the shape of a drum;
• springs: large and small;
• washers;
• coil;
• cord;
• tongues;
• Parts of fasteners.

A coil is installed in the center of the drum, on which the cord is fixed. The large spring is located in the case around the axis and is designed to return the coil to its original position after scrolling.

The mechanism of this device is quite simple, it can be assembled with your own hands.

The work of the walk.behind tractor with a manual starter is carried out as follows. The driver triggers the mechanism pulling the handle of the device. In this case, the device begins to work and starts the engine. In order for the device to successfully convey the initial rotation of the motor, the handle of the device must be pulled twice.

But despite the fact that a manual starter on a single tractor is considered a reliable device, it also sometimes fails. If the design is broken, its repair can be performed independently.

How to repair the starter of the motor.cultivator with your own hands

Consider how to repair the starter of the walk.behind tractor with your own hands. Before starting the repair of a hand starter, you need to find the instructions for its operation, which contains the device diagram. Then you need to prepare a wrench to develop the mechanism.

Before dismantling the device, it must be photographed in order to then correctly collect all the details and components.

After that, unscrew the washer, which is located in the middle of the case. Having opened the lid, you must carefully examine all the details that are located inside the drum and determine which of them are damaged. It is necessary to carefully and carefully conduct an inspection of small details, so as not to accidentally spoil them and not lose.

In most cases, the repair of a kickstarter on a walk.behind tractor consists in updating the components that failed. For example, replacing the starter cord is performed if it broke or frayed.

If a large spring fails, then you need to extract it from the drum. There are usually hooks at the location of the spring fastening. If they are not in the design, then it is necessary to heat the ends of the spring and bend them in the right direction. If the spring is completely out of order and there is a pronounced fatigue of the metal, then you do not need to try to return such a spring functionality. In this case, it is best to replace it with another. After that, we install the device in its place.

In addition to a manual starter, there are also a spring and electric steel for a single tractor. The spring mechanism has a simple design, it starts easily. The device starts after the shift of the motor. Acceleration of the motor occurs through the semi.automatic operation of the spring. You can replace a hand starter with a mechanical one yourself.

The electric starter of the walk.behind tractor is connected to the battery, from which it receives power. The device is elected using the start button. The battery determines the power of the electric steamer and the duration of the device. The installation of an electric steamer is carried out according to the electrical circuit of this design. The uniform tractor with an electric starter is durable, reliability, long service life.

Unfortunately, not all designs of motor cultivators with a manual mechanism can be converted into a spring or electric. Therefore, before starting work to replace the manual mechanism, you need to study the instructions and capabilities of the walk.behind tractor and find out if such a redistribution is possible.

Farmers should know that at the beginning of the work all motor cultivators work properly. Gradually, at the assembled unit, various components fail. In order to extend the life of the walk.behind tractor and all its parts and nodes, regular inspection of the mechanism and proper care is necessary. All components and components should be subjected to periodic lubrication with machine oil, checking their performance. To increase the productivity of the cultivator and extend its service life, it is necessary to constant proper care of this technique.

How to repair the starter of the motor.cultivator with your own hands

Consider how to repair the starter of the walk.behind tractor with your own hands. Before starting the repair of a hand starter, you need to find the instructions for its operation, which contains the device diagram. Then you need to prepare a wrench to develop the mechanism.

Before dismantling the device, it must be photographed in order to then correctly collect all the details and components.

After that, unscrew the washer, which is located in the middle of the case. Having opened the lid, you must carefully examine all the details that are located inside the drum and determine which of them are damaged. It is necessary to carefully and carefully conduct an inspection of small details, so as not to accidentally spoil them and not lose.

In most cases, the repair of a kickstarter on a walk.behind tractor consists in updating the components that failed. For example, replacing the starter cord is performed if it broke or frayed.

If a large spring fails, then you need to extract it from the drum. There are usually hooks at the location of the spring fastening. If they are not in the design, then it is necessary to heat the ends of the spring and bend them in the right direction. If the spring is completely out of order and there is a pronounced fatigue of the metal, then you do not need to try to return such a spring functionality. In this case, it is best to replace it with another. After that, we install the device in its place.

In addition to a manual starter, there are also a spring and electric steel for a single tractor. The spring mechanism has a simple design, it starts easily. The device starts after the shift of the motor. Acceleration of the motor occurs through the semi.automatic operation of the spring. You can replace a hand starter with a mechanical one yourself.

The electric starter of the walk.behind tractor is connected to the battery, from which it receives power. The device is elected using the start button. The battery determines the power of the electric steamer and the duration of the device. The installation of an electric steamer is carried out according to the electrical circuit of this design. The uniform tractor with an electric starter is durable, reliability, long service life.

Unfortunately, not all designs of motor cultivators with a manual mechanism can be converted into a spring or electric. Therefore, before starting work to replace the manual mechanism, you need to study the instructions and capabilities of the walk.behind tractor and find out if such a redistribution is possible.

Farmers should know that at the beginning of the work all motor cultivators work properly. Gradually, at the assembled unit, various components fail. In order to extend the life of the walk.behind tractor and all its parts and nodes, regular inspection of the mechanism and proper care is necessary. All components and components should be subjected to periodic lubrication with machine oil, checking their performance. To increase the productivity of the cultivator and extend its service life, it is necessary to constant proper care of this technique.

Do.it.yourself starter renovation

Despite the high quality and reliability of modern starters, some owners sometimes face the need to repair them. Most often, the breakdown of the mechanism is insignificant, which allows you to quickly eliminate the malfunction with your own hands. The procedure for dismantling and further repair of the mechanism is as follows:

• The repair of the node should start by studying its scheme. If the design of the motor block provides an electric type starter, then before dismantling the mechanism you need to familiarize yourself with the location of its terminals;
• Using the key from the kit of the walk.behind tractor, unscrew all the screws and nuts that hold the mechanism in the design of the walk.behind tractor;
• If the dismantling of the node is carried out for the first time, we advise you to photograph the starter before finally remove the mechanism from the unit;
• Next, unscrew the washer located in the central part of the drum body and carefully examine the internal parts for breakdowns;
• All further actions depend on the malfunctions of the starter details. If the cord came out of the system. it was erased or torn, then to replace you will need to wind a new product, adhering to the marks on the drum body of the mechanism;
• Another common breakdown is a spring malfunction, or rather, its antennae, the edges of which should be bent in the form of hooks. If the antennae broke off, then the edges of the spring will need to be heated, and bend them so that the spring can be hooked by the holes in the drum. In this case, the residual length of the spring is of great importance. make sure that the part does not stretch too much. If you find that the spring is very short, or it has already begun to rust, it is better to replace it entirely.

Before mounting the starter back on the one.legged tractor, we advise you to first clean the space inside the unit structure. This will prevent garbage from getting into the motor, carburetor and on the spark plug.

How to repair the starter of the motor.cultivator with your own hands

Consider how to repair the starter of the walk.behind tractor with your own hands. Before starting the repair of a hand starter, you need to find the instructions for its operation, which contains the device diagram. Then you need to prepare a wrench to develop the mechanism.

Before dismantling the device, it must be photographed in order to then correctly collect all the details and components.

After that, unscrew the washer, which is located in the middle of the case. Having opened the lid, you must carefully examine all the details that are located inside the drum and determine which of them are damaged. It is necessary to carefully and carefully conduct an inspection of small details, so as not to accidentally spoil them and not lose.

In most cases, the repair of a kickstarter on a walk.behind tractor consists in updating the components that failed. For example, replacing the starter cord is performed if it broke or frayed.

If a large spring fails, then you need to extract it from the drum. There are usually hooks at the location of the spring fastening. If they are not in the design, then it is necessary to heat the ends of the spring and bend them in the right direction. If the spring is completely out of order and there is a pronounced fatigue of the metal, then you do not need to try to return such a spring functionality. In this case, it is best to replace it with another. After that, we install the device in its place.

In addition to a manual starter, there are also a spring and electric steel for a single tractor. The spring mechanism has a simple design, it starts easily. The device starts after the shift of the motor. Acceleration of the motor occurs through the semi.automatic operation of the spring. You can replace a hand starter with a mechanical one yourself.

The electric starter of the walk.behind tractor is connected to the battery, from which it receives power. The device is elected using the start button. The battery determines the power of the electric steamer and the duration of the device. The installation of an electric steamer is carried out according to the electrical circuit of this design. The uniform tractor with an electric starter is durable, reliability, long service life.

Unfortunately, not all designs of motor cultivators with a manual mechanism can be converted into a spring or electric. Therefore, before starting work to replace the manual mechanism, you need to study the instructions and capabilities of the walk.behind tractor and find out if such a redistribution is possible.

Farmers should know that at the beginning of the work all motor cultivators work properly. Gradually, at the assembled unit, various components fail. In order to extend the life of the walk.behind tractor and all its parts and nodes, regular inspection of the mechanism and proper care is necessary. All components and components should be subjected to periodic lubrication with machine oil, checking their performance. To increase the productivity of the cultivator and extend its service life, it is necessary to constant proper care of this technique.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work, you will need a screwdriver with the tip of the desired shape.

Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.

Parsing the starting node

They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:

• spin a screw with a screwdriver, fixing the pulley with a starter lid;
• take out a spring and antennae;
• Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
• determine why the launch mechanism has broken;
• If the spring collapses almost completely, then it is replaced;
• When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);

After the spring plate is installed inside the groove, it is carefully twisted. To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst

Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges

To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst

Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges

Immediately putting a springy plate in the same place does not always work. It often slips, so attempts are required to repeat until the desired result is achieved.

Starter assembly

The assembly of the starting node is carried out in a number of stages:

The coil is turned over, installing it so that the spring bend exactly stands into the groove of the case, as in the photo below;

When making the stated manipulations, it is necessary to lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled. Because of this, a feeling appears, as if the spring had flown. To eliminate such a drawback, you need to install this part of a larger length or an additional goal.

When such spare parts are absent, you can just unscrew the screw a little, and the starter knot will begin to work without shaken. But this option is temporary. it is better to repair qualitatively as quickly as possible.

Spring tension

After installing the spring, it should be pulled. The following actions are performed for this:

• Remove the handle from the starter cord;
• Then the rope is inserted into the coil groove;
• They stretch the spring, rotating the coil in the direction opposite to the clock of the clock arrow (reviews);
• make the desired number of revolutions specified in the instructions for the use of the trimmer model used and the corresponding length of the cord used;
• At the very end, the rope is threaded into a hole designed for this, located in the starter cover;
• put the handle in place, fixing it with a node.

If after the repair the spring continues to fly, then you can get rid of this in the following ways:

• Squeeze the suitable piece of the plate into the groove at the location of the spring hook;
• drill holes on two sides of the groove in the coil, into which the spring hook is inserted and fix it using a wire.

Replacing a torn cord

A torn rope is replaced in the following sequence:

• The old cord is removed;
• choose a suitable rope (thickness and length);
• Having reached it through a special hole in the coil, a knot is tied;
• Sprinkle a spring, producing the required number of revolutions;
• Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way

In this case, there are some nuances associated with their constructive features.

How to choose a starter for a single tractor?

Motobobes do not constitute complex designs, but at the same time they contain certain features. For example, when using this device, two starters work simultaneously: the main and additional. In addition, the role of assistants can also play spring and electrical options.

The latter are considered the most popular, since they can be installed without problems on motoblocks and carry out repair work. A distinctive feature of such starters also consists in the fact that they are unpretentious, therefore they do not require too careful use.

Features of the manual mechanism

In the process of choice, most users usually prefer a manual starter. It has a huge number of advantages in comparison with electric and other options. Such a device includes the following details:

It is the manual starter that is most popular, since during operation such devices often fail, so they have to be repaired, but just manual options are extremely easy to repair. Consider how the process of restoring the performance of the starter looks like.

• Before starting the repair, you need to find a scheme from the manufacturer to understand the features of the location of all parts. In addition, it will be useful to understand the instructions.
• You need to prepare the key with which you can unscrew and remove the nuts.
• Before shooting a starter, it is best to take a few photos. This will help restore everything if you forget the location of certain details.
• Unscrew the puck that is located in the center of the drum.
• Find damaged elements and conduct their replacement.

Thus, the repair of a hand starter does not take too much time, so this variety is very popular. In the process of restoring the performance of the starter for the walk.behind tractor, the main thing is to pay attention to any details, even the smallest.

For a walk.behind tractor, you can also install other types of starters. Among the most popular and demanded in the market, several types of.

• Spring, which are considered the simplest both in use and installation. In order to start such equipment, you will just need to move the motor block handle. The unit includes a semi.automatic spring, which provides the necessary acceleration of the power plant. In order to replace the manual version with a mechanical version, it will take no more than two hours.
• Electric ones that work from built.in battery. It is the last detail that determines the level of power of the device and its autonomous operation period. It should be noted that such starters can not be installed on all motoblocks. Only some models are able to work with electricity, so before choosing you must definitely study the features of your unit.

In the process of choosing any starter, it should be understood that in the first year of work they are almost all the same. If the company is conscientious, then each device will fully fulfill the functions assigned to it, but after a year the situation changes. In order for the device to work as best and longer as possible, you need to constantly care for it, lubricate and replace the failed parts. Only in this case, the starter can boast of high performance and durability.

How to repair the starter of the motor.cultivator with your own hands

Consider how to repair the starter of the walk.behind tractor with your own hands. Before starting the repair of a hand starter, you need to find the instructions for its operation, which contains the device diagram. Then you need to prepare a wrench to develop the mechanism.

Before dismantling the device, it must be photographed in order to then correctly collect all the details and components.

After that, unscrew the washer, which is located in the middle of the case. Having opened the lid, you must carefully examine all the details that are located inside the drum and determine which of them are damaged. It is necessary to carefully and carefully conduct an inspection of small details, so as not to accidentally spoil them and not lose.

In most cases, the repair of a kickstarter on a walk.behind tractor consists in updating the components that failed. For example, replacing the starter cord is performed if it broke or frayed.

If a large spring fails, then you need to extract it from the drum. There are usually hooks at the location of the spring fastening. If they are not in the design, then it is necessary to heat the ends of the spring and bend them in the right direction. If the spring is completely out of order and there is a pronounced fatigue of the metal, then you do not need to try to return such a spring functionality. In this case, it is best to replace it with another. After that, we install the device in its place.

In addition to a manual starter, there are also a spring and electric steel for a single tractor. The spring mechanism has a simple design, it starts easily. The device starts after the shift of the motor. Acceleration of the motor occurs through the semi.automatic operation of the spring. You can replace a hand starter with a mechanical one yourself.

The electric starter of the walk.behind tractor is connected to the battery, from which it receives power. The device is elected using the start button. The battery determines the power of the electric steamer and the duration of the device. The installation of an electric steamer is carried out according to the electrical circuit of this design. The uniform tractor with an electric starter is durable, reliability, long service life.

Unfortunately, not all designs of motor cultivators with a manual mechanism can be converted into a spring or electric. Therefore, before starting work to replace the manual mechanism, you need to study the instructions and capabilities of the walk.behind tractor and find out if such a redistribution is possible.

Farmers should know that at the beginning of the work all motor cultivators work properly. Gradually, at the assembled unit, various components fail. In order to extend the life of the walk.behind tractor and all its parts and nodes, regular inspection of the mechanism and proper care is necessary. All components and components should be subjected to periodic lubrication with machine oil, checking their performance. To increase the productivity of the cultivator and extend its service life, it is necessary to constant proper care of this technique.

How to choose a starter for a single tractor?

Motobobes do not constitute complex designs, but at the same time they contain certain features. For example, when using this device, two starters work simultaneously: the main and additional. In addition, the role of assistants can also play spring and electrical options.

The latter are considered the most popular, since they can be installed without problems on motoblocks and carry out repair work. A distinctive feature of such starters also consists in the fact that they are unpretentious, therefore they do not require too careful use.

Self.repair of the starter. algorithm in details

Over time, a hand starter of the used motoblock often fails. In this case, the mechanism will need to be dismantled for repair or complete replacement of broken elements. In order to prevent errors when removing the starter, you will need to use the scheme from the manufacturer of the walk.behind tractor.

Repair of the starter starter is carried out in the following sequence:

• There is a puck in the central part of the starting drum. It will need to be unscrewed in the first place;
• Gently disconnecting the cover of the starter case, after which it is necessary to inspect all the spare parts of the mechanism not the subject of breakdowns;
• Motoboblock kickstarter consists of a mass of small details. it is very important not to lose them during the repair. To do this, all elements should be laid out on a piece of an old newspaper or fabric;
• Most often, the repair of the starter implies the replacement of worn parts. over, the length and width of new spare parts is of great importance. If they are too large, then the hull cover will not close, and the one.axine tractor will not start;
• Very often a large spring is subject to replacement in the design of the starter. There are special hooks at its ends, with which the part clings to other elements of the mechanism. When replacing the spring, you should be extremely careful so as not to damage the hooks.

Replacing failed starter parts. the procedure is not complicated. The main thing during the repair is not to try to restore the original shape and functionality of highly worn spare parts, otherwise the use of a walk.behind tractor with such details will lead to accelerated wear of other important mechanisms of agricultural machine.

How to put a starter on a single tractor. the right procedure

Remove the electric starter from the walk.behind tractor in order to further repair the broken mechanism even a beginner. However, with the reverse installation of the starter on the unit with their own hands, many beginner farmers, as a rule, have problems. Due to improper installation, the starter does not launch the engine engine even after several strong jerks. In order to prevent typical errors, you should study the algorithm for installing the starter on a single tractor in more detail.

The installation of the starter should be performed in this order:

• First you need to remove the flywheel. this will be required to install and fix the crown on it. To dismantle the flywheel, you need to dismantle the air filter, which will give free access directly to the internal structure of the motor block available in the farm;
• Then you need to remove the protective casing and unscrew the screws that attach the basket of the starter mechanism, the flywheel and its nut. The removal of the flywheel, as a rule, causes certain difficulties, and therefore many experts advise immediately before repairing the walk.behind tractor to purchase a removable key. As soon as the flywheel is dismantled, you should turn the veneer, which is immediately behind the flywheel;
• After that, the generator should be installed. The wiring in it must be sat in a hole located in the metal wall of the engine. Then the generator will need to be fixed in a place on the wall of the motor;
• Further inside the existing flywheel, it is necessary to install generator magnets. In this case, all available holes in the flywheel and generator must match. Both elements will need to be connected by fasteners, after which it will install the crown of the used motorcycle unit. Immediately before the installation of the crown, it must be heated with a ballest burner;
• The assembled mechanism must be installed on the motor block, while screwing the nut and the vene of the flywheel;
• Next, screw the starter basket, fix the casing and motionlessly install the standard air purification filter in the regular place;
• Then you need to remove the plug and put the starter itself on the engine;
• Next, you will need to connect the generator wiring to the charging relay;
• At the final stage, starting terminals must be connected to the engine of the walk.behind tractor and start the unit.

It is not as difficult to install a starter on the uniform tractor in the household, as it seems at first glance. The most important thing is to be as attentive as possible and adhere to the correct assembly algorithm.

All of the listed methods of repairing the starter are suitable for owners of Neva walk.behind shoes, cascade and agro. The procedure for removing and reverse installation of the mechanism will be similar to agricultural machines of all listed manufacturers of technology.

How to make a hand starter on a single tractor

As in the case of the manufacture of an electric steamer from improvised means, make a hand starter for a walk.behind tractor (Neva, Oka, Cascade, Patriot and others) will be a simple task for a master who has appropriate knowledge.

To assemble a home.made kickstarter, the installation of the handle should be added to the materials described above and the procedure for transmitting the effort, which will replace the operation of the electric motor. The foothold of a hand starter can be made of a thin metal pipe, which will need to be bend in the shape of the foot and install in the hollow hole of the coil. Having collected the device, you should definitely weld it.

Which starter is installed on your walk.behind tractor?

Features of the manual mechanism

In the process of choice, most users usually prefer a manual starter. It has a huge number of advantages in comparison with electric and other options. Such a device includes the following details:

It is the manual starter that is most popular, since during operation such devices often fail, so they have to be repaired, but just manual options are extremely easy to repair. Consider how the process of restoring the performance of the starter looks like.

• Before starting the repair, you need to find a scheme from the manufacturer to understand the features of the location of all parts. In addition, it will be useful to understand the instructions.
• You need to prepare the key with which you can unscrew and remove the nuts.
• Before shooting a starter, it is best to take a few photos. This will help restore everything if you forget the location of certain details.
• Unscrew the puck that is located in the center of the drum.
• Find damaged elements and conduct their replacement.

How to repair a hand starter for a walk.behind tractor with your own hands?

The main thing is very neat to all small things, so as not to lose them. Most often, the repair of the starter involves updating unsuitable details. For example, the replacement of the starter cord will be relevant if it is completely rushed or torn.

With a large spring, everything is somewhat more complicated, because at the ends of the mounting places there are special hooks. If they are absent, it is necessary to heat these very ends and bend in a suitable direction. An important point: do not try to return the former functionality to the element when the pronounced fatigue of the metal is observed. Replacement will be the best way out.

What other types of starters are suitable for a walk.behind tractor?

Each owner of motoblocks must understand that at first absolutely all starters function perfectly and can delight their owners with such a state of affairs for about a year. But without periodic lubrication of details, their verification and the commensurate power of a jerk, such joy will not last long. Take care of the starter and he will answer you with high performance and a long service life.