Make a hitch for a tiller with your own hands

Installing the hitch on the tiller

To the tiller brackets, the hitch brackets are installed using pins. For a more reliable fastening, it is recommended to fix the bracket using M14 bolts.

Tiller Hitch Drawings

Below are the drawings of a universal hitch suitable for most popular brands of tillers, such as: Celina, OKA, Neva, Salyut, Favorit, etc.

Purpose of the universal hitch in conjunction with the tiller of attachments: harrows, plows, diggers, planters, etc.

Do-it-yourself hitch for the tiller

The hitch for the tiller, an indispensable and most important unit in the design, without it, most types of attachments cannot be used. Structurally, this knot may differ, but the most common one can be considered a U-shaped hitch. We will try to tell you how to make it yourself. If you do the coupling to the tiller with your own hands, you need to carefully approach the whole process so that this unit turns out to be of good quality and can cope with pretty decent loads.

Installation of equipment on the coupling

To install additional equipment, it is necessary to mount the hitch axle to the equipment bracket, which, by the way, is removable. Next, an axle is inserted into the outer hole of the hitch. It is necessary to tighten the bolt, aligning the holes on the chassis and the equipment rack. Next, it remains to secure the contact with an M12 bolt and a corresponding nut.

Why do you need a hitch to a tiller. no need to explain, the same adapter, an irreplaceable thing, but nowhere without a coupling.

Tips for work

Attachments connected to the tiller through a hitch can be easily adjusted for a certain type of work and the specifics of the soil. Thanks to its design, the hitch is adjustable in various parameters. Using the initial settings, it is necessary to set the hitch grooves to “0” of the transverse grip angle, and fix it with a bolt and nut. Also deduce the minimum longitudinal angle of capture. The first few meters when working, watch how the tiller behaves with the tool.

If you need to set a greater depth or, on the contrary, reduce it, stop the tiller, and use the screw handle to adjust the linkage. After these manipulations, you can continue to work, along the way watching the work of the tiller and the tools.

Do-it-yourself hitch to the tiller

For the manufacture of a U-shaped coupling, a metal channel of the required size and thickness is suitable. This mount is located under the steering column of the tiller.

Following the drawings, we drill holes in certain places through them. The bracket and pin will be attached. All parts must be made of high-strength, high-quality steel, and do not forget about the diameter of the holes.

In order to attach a hitch to the tiller, you need a bracket located in the direction of the top or bottom, while its end should not come into contact with the surface to be treated.

Often, working with a tiller implies the use of equipment that does not have a typical type of coupling. Often, additional devices are used for the tiller, with non-standard types of coupling. In this case, additional adapters are used to connect them.

Tiller hitch video

This video tells about the self-production of the hitch for the Weima 1100D tiller

Homemade universal hitch

The hitch gives great opportunities in the use of various equipment, and made by hand, adhering to the instructions on the drawings, then the service life of this unit is many years.

DIY universal hitch for a tiller

The universal hitch is suitable for most models of tillers, will provide aggregation with attached or trailed equipment without backlash. It is quite simple to make a coupling device, the main thing is to determine the tasks that it should solve, choose drawings and high-quality materials that ensure the strength of the unit.

The U-shaped trailer hitch will fit most of the trailer. The main point in creating a hitch is to match the dimensions of the brackets of the tiller itself and the hitch. A feature of the device with a bracket is that the attachment, aggregated with it with a tiller, takes a position a few centimeters below the bracket itself, so it should not be at the level of the cultivated land.

You can find many videos on the Internet in which trailer owners talk about the nuances of working with attachments, including how to make a hitch.

How to make a do-it-yourself hitch for a tiller: drawings and dimensions of a universal hitch, video

In some situations, it may be necessary to make a do-it-yourself hitch for the tiller. tiller is an essential attribute of any gardener. The purchase of a motor-cultivator is often accompanied by the purchase of related parts: a trailer, a hiller, a plow, a harrow and other parts. In order to attach them to the unit, a hitch is required. Now on the market cultivators are represented by a huge number of manufacturers, however, not for every unit you can find a suitable spare part, therefore you can make a hitch yourself.

Tiller hitch types

There are the following types of hitch for tillers:

The POOR MANS Tractor Mounted Tiller- A Walk Behind Converted To A 3 Point Mount!!!

• Single or double, which are used depending on the amount of equipment attached.
• Reinforced, used for heavy cultivator models. Compared to the single or double version, this type of tiller hitch is much thicker and longer, due to which the attachments will sink deeper into the ground, which will improve the quality of plowing.
• With an adjustable angle of rotation of the shaft, which will facilitate the placement of additional equipment at the required level, this will greatly facilitate the work with the cultivator.
• Versatile, suitable for several models at the same time.

But do not be upset if you cannot find a hitch for your cultivator. you can do it yourself. Some craftsmen are even able to make the whole tiller with their own hands, so it will not be difficult to build an ordinary coupler. For example, a hitch for a tiller, made by hand from a crosspiece, used parts and spare parts. On the Internet, you can easily find drawings of couplings for a tiller, the main thing is to correctly calculate the dimensions. The most popular is the U-type hitch.

How to make a hitch on a tiller with your own hands

Consider how to make a do-it-yourself hitch. A homemade hitch for a tiller will require the purchase of high-quality metal products, which can be channels, it will be necessary to make several holes in them. Or some car parts will do (the trailer hitch can be made from a cardan). If a reinforced mount is needed, then it must be stronger and larger than the usual variety.

The drawings on the Internet are different, so you need to choose the one that suits you.
To make a coupler you will also need:

• fasteners (steel pins, bolts);
• a lever that allows you to change the position of the hitch;
• metal welding to attach the shaft;
• drill and drill for metal;
• tape measure or ruler;
• screw installation wrenches.

So, the universal hitch for the tiller includes the following components:

• Two U-shaped nodes of the same size, one of which is equipped with 6 holes, and the other. 8.
• A body (to create which requires welding), which has 2 threads: M12 and M16 and a connecting element with one of the nodes.
• Adjustment lever located in the body and consisting of a screw connected to the bracket and handle. In this case, the bracket must be directed up or down and not create any interference with the operation of the unit.

How to correctly position the connecting unit, you need to look in the instructions for the unit.

The hitch is attached to the tiller with pins that are installed in the holes made in the nodes, while in quality they must be the same as the materials from which the hitch itself is made.

Do-it-yourself hitching to the tiller is performed to connect not only the trailer, but also the plow, hiller and other devices. At the same time, it will be possible to adjust it by adjusting it to a certain attachment.

Before starting work, the device should be checked, tighten all the bolts.

It should be noted that it is not difficult to make homemade couplings on your own, but it is better to purchase a unit by picking up the entire set of attachments and additional equipment for it at once, or at least make sure that such devices exist.

Let’s consider how to choose a hitch for the Tiller Neva. Now you can buy cultivators from various manufacturers, differing in weight, size, quality and performance. Consider the Neva tiller, which is especially popular among gardeners and gardeners, whose production was launched in St. Petersburg back in 2002 at a subsidiary of OJSC Krasny Oktyabr, which produces aircraft.

In the production of chillers, engines Subaru, Briggs Stratton, Honda are used, which have an increased resource and efficiency, which contributes to efficient soil cultivation. The device has a fairly simple and understandable gear shifting system even at first use. For Tiller Neva, you can easily pick up various kinds of attachments manufactured for a specific brand.

The plant produces several models of tillers, at the same time it divides them into 2 large groups, differing in the gearbox: classic and Multi AGRO.

The main category of users of tillers are retirees, so most often one of the inexpensive, but lightweight and high-quality models is purchased. MB-B6.5 RS Compact, which weighs only 70 kg, is well suited for processing sandy, loamy soils.

Using additional attachments for the unit, you can easily cope with the cleaning of the territory and with the transportation of goods, even over long distances.

On the Tiller Neva of this model, it is advisable to additionally purchase a support wheel, which will be useful when installing on the lug device, as well as to facilitate the work of loosening the soil due to the fact that it will not allow the tiller to “bury” in the ground.

DIY tiller plow hitch

The plow is one of the most important attachments for a tiller. However, the manufacturer does not always provide a hitch in the kit. It is not difficult to make a hitch for a plow with a tiller, you can use drawings of the simplest type. a U-shaped hitch.

Depending on how much power the tiller has and what kind of land the plow will work on, a more or less durable hitch will be needed. There is always a tremendous load on this node, so it must be made of high-quality materials, especially if heavy soil is to be worked.

What type of hitch for attachments and trailed implements do you use??

Appointment

The adapter to the tiller was created for the convenience of working in the garden. If you attach a hitch to it, then you can expand the scope of the device:

• remove hay;
• level the soil surface;
• transport goods;
• harrow the ground;
• clear the area from snow.

An adapter is a device that is designed to be moved on a motor cultivator. With it, you can operate the machine while sitting in a chair, and at the same time work the soil. The trailer for the Neva motor cultivator is equipped with steering control. It allows you to simplify the use of the tiller.

Can be fitted with different harvesting attachments, plow, mower, etc.

This trailer accelerates work in the field. With this design, the speed of the cultivator can be increased from 5 to 10 km / h. Consider the device of the adapter. The adapter for the cultivator consists of:

• frames;
• operator’s seat;
• two wheels;
• axles;
• coupling mechanism.

After attaching the adapter, the cultivator looks and works like a mini-tractor. A frame is needed to create an adapter for a front-steering cultivator. The operator’s seat is installed on it. The frame is fixed to the chassis.

The seat is fixed to the frame. This makes it easier for the operator to control the cultivator. The wheel system will help move the unit around the site. There are 2 types of wheels: metal (used in the field) and rubber (used for road traffic).

The tiller hitch is made of steel or cast iron by welding. She attaches the cart to the cultivator. The best is the U-shaped fastening system. With this design, the device will be stable.

• The highest travel speed on a trailer with a trailer is 12 km / h.
• Maximum lifting capacity. 100 kg.
• The track diameter is 67 cm.
• Dimensions are equal to 130x70x71 cm.
• Device weight. 22 kg.
• Warranty period of work. 5 years.

Steering

A quality steering wheel adapter for the tiller makes it easier to operate the cultivator. In terms of its functions, such a tiller is comparable to a mini-tractor, only it is more economical in fuel consumption. The standard APM unit from the Krasny Oktyabr manufacturing plant does not have a rudder.

The control is carried out using the steering wheel of the cultivator. But other manufacturers make steering units. The cart is designed for more comfortable work on the cultivator, so the presence of a steering wheel will make the operation easier.

Assembling the adapter for the tiller

First, make the frame. It is made from pieces of metal of the required length. The metal is cut by an angle grinder and the parts are connected by welding or screws.

Then they carry out the chassis. When the cultivator motor is located at the front, then the base wheels determine the track gauge. The rear ones are attached to the frame using an axle. It must be made from a pipe of the required diameter. Bushings with bearings are attached to its ends.

Then wheels are mounted on them. When the cultivator motor is at the rear, the tread should be wider. Otherwise, the structure will not be able to maintain balance during operation. Then the base cultivator wheels must be removed and fixed on a wide axle.

To make your own steering wheel, you do not need to remove the handle of the car. If you use the handle from the cultivator, you can control the entire structure using the motorcycle handlebar. But it will be difficult to back up. Therefore, it is best to mount a sturdy steering column.

Consider the manufacture of a frame for a trailer of a motor cultivator. With a solid metal frame, steering will be directed to the front axle of the unit. You can make a frame on hinges, while the steering column will rotate completely onto the front frame. To achieve this, mount the gear to the front frame.

The second gear is mounted on the steering column. Then a seat for the tractor driver is made. It can be taken from a car. The seat is welded onto the frame. It can be regulated. This is especially necessary for the front type device. The driver’s seat is now attached.

To attach a trailer to a tiller with a plow, a bracket must be installed. To work with the mower, you need to make a hydraulic system. To work on the device, you need to weld the towbar from the car to the rear, where the metal frame is located. The pump can be borrowed from any unit for agricultural work.

Thus, all the necessary parts and assemblies of the adapter for the cultivator are made. Now you need to assemble the entire structure. After that, it needs to be checked and tested in work. If all components are operating normally, then you can start operating the unit.

Scheme and structural elements

To make an adapter with your own hands, the drawings and diagrams of this device must be completed first of all. And according to the ready-made scheme, indicating all the parts, assemblies, structural elements and their dimensions, it will be easier to start the independent manufacture of the unit.

Do-it-yourself steering wheel on the tiller

Steering Tiller Adapter makes maneuvering easier and more stable. Making a steering wheel for a tiller with your own hands is quite easy if you have basic welding skills.

You can create a structure from a steering mechanism from a car; it is better to use a steering column with a bipod from trucks, tractors. The bipod can be used to hitch the rear adapter to the cultivator. The steering arm is indispensable if the trailer design does not imply steering levers. When making an adapter with a steering wheel for a tiller, you can make a ball joint that allows the wheel to turn freely in a horizontal plane.

If the equipment is used for plowing the ground or other difficult work, then it is better to make the steering and the trailer-tiller connection mechanism independent, since there will be a large load on the hitch unit.

With movable joint

With a movable hitch of a trailer with a cultivator, the angle of the vertical axis between the cart and the cultivator changes. It is easier to make such a device, but when turning, you will need to exert more force. This type of trailer is inferior in geometric characteristics: the turning radius becomes larger.

Front and rear adapters

There are several types of trailers, depending on which wheels are driving:

• Front-wheel drive. The unit is fixed behind the tiller. This is the simplest and most popular modification. It makes it easy to operate the cultivator and carry out a large amount of work.
• Rear drive. The unit is located in front of the cultivator. This design makes it possible to carry out work when using a hitch located at the rear of the cultivator.
• Four-wheel drive. The trailer can be located both in front and behind the cultivator. This design differs from the previous ones in that not 2 wheels rotate, but all 4 wheels at once. Such a device performs the functions of a mini-tractor. This increases the maneuverability of the structure, its cross-country ability, additional adhesion to the soil is carried out. The 4×4 drive is considered the most efficient.

The rear adapter is the most common type of trailer for the tiller. It can be used as a trolley (lifting capacity about 100 kg), for aggregation with attachments for plowing, mowing, snow removal, etc.

Steering trailer allows maneuvering in different terrain, making the operator’s job easier. It can be inconvenient and dangerous to operate the structure using the steering wheel of the cultivator itself. When working in a field with uneven terrain or in a vegetable garden, it is better to use a trailer with a steering wheel for a tiller, as it is easier to drive.

In order to make a back adapter with your own hands, readily available materials are suitable. The basis of the trailer design is the frame; it can be made of a metal profile or a metal pipe. The hitch assembly can be movable or rigid. In the second case, a change in the cultivator itself will be required, so the creation of a movable hitch is less complicated.

The rear adapter is used for work that requires constant supervision (hilling the beds), so the design necessarily includes a seat for the operator’s convenience. It also facilitates the work of the presence of steering, which is made from the steering mechanisms of any vehicles.

Drawings of different types of couplings

Required tools and materials

A person engaged in economic activities on the land usually has a sufficient set of equipment for the manufacture of a coupler. To work, you need the following tools:

• Angle Grinder.
• Drill, drilling machine.
• Measuring tool: ruler, tape measure, square.
• Welding machine.
• A set of keys.

You can find about the hitch for the Tiller Neva in the article.

It is important to choose the right drill for the diameter of the studs and bolts. The absence of backlash will extend the life of the attachment. The body can be cut from sheet metal or a suitable channel can be used.

Preference should be given to a hitch with an adjustment mechanism. In this case, you can use attachments of different classes, from different manufacturers, achieving maximum efficiency in work.

The photo below shows a universal hitch with a threaded adjustment mechanism. A simple but effective device that is not difficult to make with your own hands:

Working with a drill for metal will be easier and more productive if you make a preliminary hole with a smaller diameter during drilling. For example, a 5 mm drill is used first, and then 12-16 mm for the size of the bolt.

DIY Tiller Hitch

In practice, the owner of the tiller is faced with the limited capabilities that the standard delivery set has. A properly made do-it-yourself hitch will not only save on buying a factory sample, but also get expanded opportunities for the effective use of existing attachments.

How to make a hitch for a tiller yourself

During operation, the device will be subjected to a large load, therefore, the recommended dimensional and strength characteristics of all assembly elements should be adhered to. In this case, the following coupling qualities will be guaranteed:

• Ensuring a secure fit with the tiller.
• Attachment to attachments.
• Ensuring the declared operational qualities of equipment.
• Affordable price.
• Reliability, long service life.

When choosing a model, you should check the dimensions that the trailer hitch and attachments (plow, trailer, harrow, etc.) have. The task of the wizard is to ensure full compatibility of elements, ease of use and the ability to easily configure equipment for a specific task. The main part of the hitch is a U-shaped bracket. Through the holes on one side, it is attached to the tiller with pins, on the other side, the rack of the necessary attachments is fixed to the device body.

Making a universal connection

You need to do the work on a flat surface. A table of the right size or workbench will do. The order of work is as follows:

• Markup. According to the drawing, the contours and dimensions of the elements are indicated.
• Drilling. The operation is performed with a drill or on a machine. The accuracy of the holes is checked with a vernier caliper, as well as a pin or bolt, inserting them into the seat. Both backlash and jamming of parts are excluded. To facilitate work and to avoid injury, the holes are machined with a countersink.
• Welding. It is preferable to use electric welding. The metal heats up only at the junction and does not critically lose its properties. If a suitable channel is not found, then a structure is made of sheet steel of the required quality.
• Assembly. The bracket is bolted to the channel. If an adjusting mechanism is provided, then it is also fixed to the structure.

Attaching attachments to the tiller using a hitch

Attaching attachments is reduced to a simple operation of aligning the holes and fixing the structural elements with pins and bolts. During operation, the position of the hitch can be adjusted using the bolts in the radius holes. First of all, the threaded connections of the hitch with the tiller’s hitch are tightened. Then the hitch is installed.

How To FIX a Tractor Hitch John Deere 7810. John McClean | FarmFLiX

The final adjustment is made before work. By loosening the adjusting bolts, find the optimal position of the attachment and tighten the nuts with wrenches. In the process of cultivating the land, it sometimes becomes necessary to make two or more passes through the site with different settings of the hitch. A hand-made hitch allows you to optimize work in all respects. Saves time, reduces labor intensity, increases productivity.

A hitch coated with metal paint or anti-corrosion coating will last significantly longer.

Required tools and materials

There is a certain set of tools that are required to make a coupler, but they do not include anything exotic. Usually, everything that is required to assemble such parts is on the farm of any owner who cultivates his land plot. The following tools are required:

• welding machine;
• Angle Grinder;
• drill or drilling machine, drill bits for metal;
• measuring instruments (tape measure, ruler, square);
• keys;
• fasteners (bolts, studs).

It must be emphasized that in this case it is very important that the holes that you will drill into the parts exactly coincide with the bolts and studs. a backlash in diameter is undesirable, since it will shorten the service life of the used attachments and trailers. At the same time, during the manufacturing process, it makes sense to first make holes in the part with a smaller diameter (from 5 mm), and then expand with wider drills (up to 12-16 mm, depending on the diameter of the bolts). this approach will speed up and facilitate this part of the work, at the same time allowing you to align the holes as accurately as possible.

For the manufacture of the case, you can use a channel of a suitable size, and if there is none, you can cut out a part from a metal sheet.

The option of an adjustable hitch is very convenient. this design will allow you to attach attachments of different classes, generations and brands. Even if at the moment this design is not relevant, one should not forget that different devices may appear on the farm over time, and the possibility of convenient aggregation of any of them will significantly expand the choice, allowing only to proceed from the desired performance characteristics of the equipment.

DIY Tiller Hitch

Auto mechanic specializing in agricultural machinery

Some owners of small agricultural machinery buy it, initially counting on the versatility of the unit, others buy it for one specific purpose, and over time they can expand the range of tasks that a tiller can do. But in any case, the fulfillment of most of the functions on the arable or adjacent plot is provided by various attachments, which are attached with the help of such a part as a hitch to the tiller and, in fact, serves as the key to its versatility.

Often, the owners of agricultural units find that the factory equipment is far from perfect, the design of the coupling is not suitable for the current needs of the land economy, or is simply not reliable enough. Fortunately, there is always the option to equip your tiller with a hitch that will maximize the efficiency of the unit.

Tow hitch with his own hands for a trailer or adapter!

The hitch can be done by yourself

Blueprints

Assembling a hitch for a tiller with your own hands involves the use of drawings. There are quite a few different options available, but it is optimal to take the most suitable one as a basis and adjust it taking into account the parameters of your technique. The drawing should show the following details:

• two U-shaped components, identical in all respects, but with a different number of holes. 6 in one, 8 in the other;
• body, including two threads with diameters M12 and M16 and equipped with a connecting structure for fastening with one of the nodes;
• adjustment component. a lever located on the body of the part, its design consists of a screw connected to the bracket and for convenience has a handle; it is important to provide for the correct direction of the bracket. only up or down and in such a way that it does not interfere with the operation of the tiller;

Since the unit in any case provides for a connection with a hitch, the details of the placement of the connection can be studied in its standard instructions.

Do-it-yourself hitch for a tiller

The great advantage of a home-made device is that the owner takes into account his requests and makes it based on the input he needs: tiller model, load, attachment parameters.

But the first thing that must be taken into account is that in any case an increased load will fall on this node, therefore it is important to carefully approach the dimensions, design and level of strength of all parts of this part. Correctly specified parameters of the device will provide the most reliable aggregation with the tiller, the necessary mobility of the unit and the durability of its use.

When deciding on the design, pay attention to the dimensions of the towbar of your tiller and the features of the attachments (already available and the one that is planned to be purchased). The primary task is to ensure maximum compatibility of the unit with all necessary attachments and trailers. Equally important is the ease of use and the possibility of aggregation with equipment having different parameters.

The main working part, as a rule, has a U-shape and serves as a bracket, which is fixed to the chiller through the holes in it. The attachment stand is attached to the other side of it.

Before assembling the hitch, carefully read the instructions.

Tiller hitch selection

Any attachment or hitch for the tiller, be it a harrow, a hiller, a mower, a trailer or any other equipment, is attached with a hitch. If the basic part is not suitable, the owner has a choice. to purchase a suitable one or to make a coupler for the tiller with his own hands. In any case, when deciding which version of the node can most closely match the tasks that the unit performs, a number of points must be taken into account, including:

• features of a tiller or cultivator;
• the scope of the unit. the functions that it performs;
• equipment that must be aggregated with it;
• loads;
• the need for versatility.

Based on this, you should carefully familiarize yourself with the most frequently used structures and navigate in the choice, based on the features of the one that is best suited in this case.

In this video, you will learn more about the hitch:

When choosing a hitch for a tiller, it is worth taking as a basis the most suitable type of part. There are several types:

• single / double. used in the presence of different types of weights, depending on which ones are used and in what quantity;
• reinforced. optimal for heavy units; its distinctive feature is that it is more massive. it has a greater thickness and length, which allows additional equipment to go deeper into the ground;
• adjustable. providing the ability to change the angle of the shaft, due to which you can adjust the level of attachment attachment and thereby increase the efficiency of work;
• universal hitch. allowing aggregation with several models.

If the hitch to the tiller of the desired design is not on sale or there are some of your own requests for it, it is not so difficult to make it yourself, since we are talking about a fairly simple device. Some craftsmen, who prefer to make many “accessories” to the tiller with their own hands, make a “pipe-in-pipe” hitch for the tiller trailer, make it from a cardan shaft, from a crosspiece, from other improvised parts left over from various mechanisms. The owners of such devices note that it is not difficult to make such a unit, and share their experience and drawings of the hitch for the tiller.

Step-by-step instruction

To make a universal joint, you need the most even horizontal surface. a workbench or work table. The scheme for manufacturing a trailer device (hitch) for a tiller is as follows:

• Make the markup in accordance with the drawing: mark the outlines of the parts on the workpiece.
• Use a drill or drilling machine to make holes according to the markings. Make sure of their accuracy using a caliper and a bolt (stud), which will be used for fastening. Achieve the optimum hole diameter where there is no play or jamming of the fasteners. Countersink the holes. this will facilitate further work and protect you from injury.
• Weld the joints. It is best to use electric welding, in which heating occurs only at the joints without much damage to the working qualities of the metal.
• Assemble the part. Connect the bracket and channel with bolts. If your design has an adjustment mechanism, fix it as well.

Important! Fasteners, with which the hitch is fixed to the tiller through the holes in the nodes, must be of the same quality and strength as the part itself.

Let us remind you once again that the part is manufactured in order to maximize the versatility of the tiller. With an optimally suitable hitch, convenient aggregation and long-term effective operation of any mounted or trailed equipment, including a plow, harrow, hiller, potato planter, various types of mowers, trailers and any other devices, is possible. And since the fastening elements on different equipment may differ, which often complicates the possibility of their compatibility with the tiller, it is the successful design of the hitch and the possibility of its adjustment that solve this problem.

After assembling the part, it is important to attach it correctly. The installation rules are simple enough, but it is important to stick to them. The actual connection of the equipment to the tiller is reduced to a very simple action: you need to align the holes of the hitch and hitch and fix them with bolts or pins. Radial holes allow you to adjust the position of the connector during operation. After installation, you need to tighten the threaded fasteners of the unit with the tiller. After that attachment is connected.

After the initial aggregation of devices, a final commit will follow, which must be done immediately before starting work. The adjusting components (screws) should be loosened, the optimum fixation level should be found, and then tightened with wrenches. Depending on the design, a removable threaded axle can be installed on the bracket, into which an M16 screw is screwed.

And there are a few more recommendations to be made. To preserve the working qualities of the metal and increase the durability of the part after its assembly, it is advisable to coat with an anti-corrosion compound or paint for metal.

Considering the possibility of adjusting the structure in different ranges, it is possible to set radius grooves and fix them to zero. After starting work, it is necessary to carefully observe the connection during the first meters of movement and, if necessary, make additional adjustments. The presence of a control lever allows you to change the level of fixation and fix the attachment for a greater or lesser plowing depth.

Do-it-yourself hitch to the tiller, photos, drawings

One of the important components of the units, which ensures a reliable connection of the trailed equipment with the tiller, is the hitch. There are different types of hitch assembly. However, the most commonly used is the U-shaped tiller hitch assembly. This unit is manufactured both industrially and independently. If a do-it-yourself hitch is made to the tiller, it must be strong in order to be able to withstand heavy loads.

Installing the hitch on the tiller

The hitch brace is installed on the tiller bracket, and is secured with pins. It is advisable to fix the hitch bracket with M12x60 spacer bolts, swivel to the tiller frame.

Attaching the implement to the hitch

A removable hitch axle must be installed on the implement rack bracket.
Insert an axle with an M16 thread into the hole in the hitch body and screw a screw into this thread.
It is necessary to match the holes for the M16x40 bolt on the tool stand and on the hitch body. Then this connection is fixed with an M12 nut and an M12x40 bolt.

Do-it-yourself hitch to the tiller

The U-shaped mount is at the heart of the tiller hitch, therefore, to make it, a channel of suitable thickness and size is perfect. This mount is located under the tiller’s handlebars.

When making a do-it-yourself hitch mount, you need to drill several holes in order to fix the bracket and the mounting pin in them. Therefore, the holes must be of the correct diameter. The pin also needs to be made of high strength steel.

You will need a bracket to attach additional accessories to the tiller. The long end of the bracket should be either downward or upward to avoid interference with connected equipment. In this case, the end of the bracket should not touch the surface of the soil that we are processing.

When making a homemade hitch assembly, we used a standard sample. Often, additional devices are used for the tiller, with non-standard types of coupling. To connect them to the tiller, you either need to purchase a special adapter, or make an adapter yourself. As a rule, these are U-shaped brackets.

Tiller Hitch Drawings

Consider a drawing of a universal hitch for the following types of tillers: “Pubert Quatro”, “Honda”, “AGRO”, “OKA”, “KASKAD”, “MB-90”, “NEVA”, “FAVORIT”, “SALUT”.

Purpose of the universal hitch in conjunction with the tiller of attachments: excavator, plow, one- and two-row hiller, etc.

Recommendations for work

Attachments can be adjusted and adjusted individually, depending on the type of soil and the power of the tiller. The special design of the hitch can be adjusted in different ranges. Using the initial settings, you need to set the radius grooves of the hitch to zero, the transverse grip angle, and fix it with an M12 nut and an M12 bolt. Also set the longitudinal grip angle to a minimum. The first 3-5 meters of movement, carefully observe how the tiller works with the implement.

If it is necessary to deepen or raise the implement, stop the tiller movement and adjust the implement by turning the screw handle. Then you can continue driving and evaluate how the tiller works with the gun. Also, if you need to adjust the transverse grip angle, you need to loosen the M12 nuts and M12 bolts.

Then adjust the angle in the required direction and tighten the nuts and bolts. Before starting work, all threaded connections must be tightened firmly. After the work on the soil is over, the threaded connections must be cleaned and lubricated daily. To do this, use Litol 24.