Modernization of a rotary mower for a walk -behind tractor. Characteristics

Which mower is better for a walk.behind tractor | how to choose a mower for a motor block

Harvesting of grass and hay is an integral part of modern agriculture. Grass is universal and nutritious food for animals and birds grown on large farms, small enterprises and private courtyards. Agricultural mowers are used to harvest this valuable resource, which are hinged and self.propelled. Within the framework of this article, we will try to figure it out together and find the answer to the question: which mower is better for a walk.behind tractor?

Such a topic was chosen not just like that, in the village of the same.based tractor is not a luxury or a whim, but a necessity, because it participates in almost all agricultural processes of life. That is why each owner of such a means of small mechanization tries to increase its functionality and maximize the zones of application. Including using it and for mowing grass using hinged braids. So, let’s understand how to choose a mower for a walk.behind tractor?

Types of mowers for a walk.behind tractor

And before choosing which mower it is better to buy for a walk.behind tractor, you should figure out the question of what they are generally. Hanging devices are divided into two large groups according to the principle of action:

• segmented, equipped with a frame of a special design, on which cutting elements are placed in two rows. In the active state of the mowing, cutting strips make one relatively different movements, the segments are close and the vegetation that falls between them is mowed;
• rotary, in which cutting knives make a rotational type around the vertically located axis.

Each of these types has its own characteristics, advantages and weaknesses.

How to finalize a mower so that it is mowed better

Useful tips

To facilitate work in country and personal plots, their owners have long been used by various means of mechanization, for example, motoblocks. They have various hitching options, with which almost all types of work are performed, from mowing grass to soil plowing.

At the same time, the factory hitch often turns out to be ineffective, and the craftsmen finish the designs in accordance with their requirements. Modernization did not bypass the mowers that are used to remove grass in large territories or preparation of feed for pets.

The most common rotary mowers are. They mow plant stalks due to knives rotating at high speed or sharpened discs. As a rule, the mower is driven by the movement of the walk.behind tractor. The higher the speed of its movement, the higher the speed of rotation of the rotors or discs. Accordingly, the effectiveness of the use of the hitch is increasing. However, at too high speed, the rotors will not have time to cut the grass, and it will simply be crushed to the soil.

The main essence of the improvement is to select the necessary transfer. However, it is impossible to make the necessary chain stars or pulleys at home, so some home.made people went the other way. They make interchangeable welded wheels for their walk.behind tract. Their diameter depends on the desired result of the refinement. To reduce the speed of the wheel lock, the wheel is less made, and to increase speed. more. Now, before mowing grass, a special set of wheels is also installed in addition to the mowing.

Another problem in the mocking of grass is the crushing of the grass with lateral elements of the design of the mowing. During work, the grass laid on the ground and remains dull. As a result of this, the useful capture of the unit decreases. You have to go through the same site more often, and this increases the time of its processing and fuel consumption.

As a useful finalization of the structure, craftsmen install metal corners on the side elements of the mowing, which, when the walk.behind tractor moves, direct the stalks of the grass to the mowing rotor, increasing the performance of the machine.

Another way to finalize a hinged mower for a walk.behind tractor is to install a small separate engine on it. He will work regardless of the main unit. As a result, the load on the engine engine is reduced and its resource increases.

From a trimmer for grass

In fact, the process of manufacturing a lawn mower from such a “main component” is no different from the above methods. The essence of the work is the same, and the details are used the same.

The only thing for such a device must be used from a trimmer for grass. You can take its old model, as it is naturally not profitable and not logical to disassemble the new trimmer for the grass.

Grassproof from a trimmer for grass

Such a lawn mower will be much more efficient to perform work and it will be largely easier and more comfortable for you to work with it, since it is able to “capture” a larger mowing range and still has the presence of special herbs of the collection, which you can either buy or make personally. For this process, special skills do not need, and all that you need is a piece of fabric. If you are not a lover of the process with your own hands, you can simply purchase a hand.made electric lawn from a trimmer for grass, which can boast of a compact size.

How to make a rotary mower: step.by.step instructions

Homemade hayfields have recently been of great popularity.

If you have a desire and time, you can independently make a good unit. We offer to familiarize yourself with the instructions for the design of the rotary hayfield.

Necessary material and tool

Before starting the manufacture of a lawn mower, it is necessary to prepare the following materials and details of the future device:

• disk of grain seeder. 2 pcs;
• chain from a chainsaw gearbox. 1 pc;
• knives made of hardened metal. 8 pcs;
• Shinka;
• Soshnik.

• electric screwdriver;
• pliers;
• nuts;
• carbide drills;
• drill.

Did you know? The punching mower, due to its design, is popularly called “horse”.

Process description

First of all, you will need to drill a hole on the disks using a carbide drill with a diameter of 6 mm. Then you need to attach the chink to the bunny, and the knives to Shinka.

Please note that the distance between the tire and the knife should be several mm more than the thickness of the knife. This moment is very important and necessary so that with the help of centrifugal force knives from the disk, which would ensure the performance of the main function. mowing of grass

A prerequisite is the rotation of the knife by 360 °. This will protect him from damage in collisions with stones or hard objects.

For the manufacture of axes of fasteners of knives, you will need carbon steel, the diameter of which should be at least 8 mm. It is necessary to tighten the axis until the disk.

There are no difficulties with the assembly of the rotary mowing, if you clearly adhere to the recommendations.

Rotor mower for a walk.behind tractor. Design description

The rotary mower to the walk.behind tractor is a type of attachment equipment, the function of which is to mow weeds and bushes in meadows and fields. This device successfully copes with the removal of grass in large areas, the soil of which is not treated with herbicides.

Often, the rotary mower is also called disk. this is due to the principle of its operation and constructive features. Depending on the method of connection with the walk.behind tractor, such a mower can be half.waist, hinged or trailed. Also hinged equipment of this type is classified by the location of the cutting elements in relation to the used motoblock. Therefore, the factors distinguish rotary mowers with the front, rear and lateral arrangement of cutting knives.

During operation on the site, the rotary mower is set in motion through the transmission and wheel of a motor block. The design of such attached equipment is extremely simple. one or more cutting discs along with the support wheel are fixed on the frame. As soon as the support wheel begins to move, the discs that make the mowing of vegetation begin to rotate with it.

Areas the use of rotary mowing is quite extensive. it can be used in pastures, meadows and large gardens. At the same time, the more discs are included in the design of the equipment, the greater the processed area can be.

Features of the rotary model

Rotary mowers have a simple design, which facilitates their maintenance and repair. The working bodies are discs on which knives are mounted. They are fixed on the disks using movable hinges. Discs can be from one to several. The more working disks, the wider the area of ​​the processed surface will be.

The price of spare parts and components is low. For our models of rotary braids, spare parts can be bought at any specialized store. Imported models are not older than 10 years no worse. Mowers over 10 years of imported production may not have spare parts, since some models no longer release.

The owner of the rotary mower will easily ennoble the lawn in front of the house and stocks the grass for the winter for livestock. A small model for a walk.behind tract during cleaning areas around fruit trees and beds is convenient.

They produce rotary mowers with us, as well as abroad. Among the largest and most popular models, mowers for the Neva, Dawn, Mole, Favorite stand out. Models differ in the number of working bodies and adjusting the height of the cut of grass. To clean the grass for feeding animals, you can use models up to 20 cm high, haymaking with a cut height of 5 cm showed themselves well on the adjacent territory.

Aggregate with the Motoboblome Favorite, Mole, Neva Rotor mower in several ways:

Reviews are better about hinged models for the Neva and Cascade, Mole, Favorite. Their power is higher and it is easier to work with a walk.behind tractor, since the entire processed area is visible.

According to the method of mowing grass, rotary mowers are divided into views:

• For begging grass and laying in an even row. Suitable for mowing grass on hay.
• Mulching the grass. Crushed grass quickly rolls, suitable for handling lawns.

Selecting a model for its Neva, Salute, Zorya, Favorite, Mole is recommended to take into account the following factors:

Landscape features. The purpose of acquisition (for mowing grass on hay of livestock or for aligning the lawn in front of the house). The weight of the mower (it is important during transportation, since it is difficult to transport a large model). Productivity (for a small lawn, the most miniature mower is enough with slight power). Type of a bevel of grass (for harvesting hay for livestock feed, models that mulch grass are not suitable).

Design features

Devices produced by different companies can vary in external and some technical data. The principle of the functioning of such units is identical and dictates an integral list of nodal blocks included in the design.

Standard rotary braid for grass is made of:

• frames;
• subframe;
• balancing mechanism;
• cutter;
• field divider;
• traction fuse;
• racks;
• protection of the cutting apparatus.

Frame. element designed to attach the nozzle to the walk.behind tractor. Has two axes facing the sides. One of them serves to fix the frame on the lower rods of the leading apparatus. The second is attached to the second from the overload of the rod holding due to bolts and two nuts. An element with a bracket will join the frame, which allows you to install a subframe.

The subframe is a welded part connecting the frame and cutting element. It consists of a rectangular case. On the one hand, the tube with bushings introduced into it is welded. In the middle there are “ears” designed for fastening transport traction and device that regulates the height. The side of the bracket is on which the traction fuse is attached to. On the subframe, the drive itself and the protection of the belt transmission are fixed.

The balancing mechanism is designed so that the cutting device repeats the terrain relief. Thus, the best mowing of vegetation is achieved. Using this mechanism, the mower is also converted into transportation mode. Its adjustment is carried out by special tension bolts.

Cutting device performs mowing. Its body serves as a whole crankcase. The cutting elements are based on the soil through a special pallet installed below. The cutting device can have on its body how much rotors. There are usually two of them in the motoblock modification. Rotors are equipped with two knives. The transmission of mechanical effort from the motor to knives occurs by means of a belt of traction, gearboxes, a number of shafts and gears.

Field divisor helps to separate mowed and dwarf grass. It consists of their shield, springs and bolt fasteners. The spring mechanism allows the divider to move back at the time of overflow of the cut vegetation.

During the mowing process, the cutting mechanism may come across an obstacle. In order to avoid a breakdown in this situation, the rotary mower is equipped with a traction fuse. Using this node, a braid for grass can deviate from the working position to the moment established by the user.

The stand helps to hold the hinged unit in a convenient position at the time of its connection to the walk.behind tractor.

The assembly knives rotate at high speed. For the safety of a person using equipment, they are placed in a protective casing. It can be made of light metal or tarpaulin fabric.

Various modifications of rotary braids can differ in the presence of certain details. Some of them can be purchased, and others are made independently.

Service and storage

The duration of the uninterrupted operation of the mechanism of a motor.block braid for grass directly depends on regular maintenance. Within the framework of the service work, the device is cleaned from herbal residues, dirt and dust. The degree of tightening of the threaded joints is checked. the weakened are pulled up. The tension of the belt is measured. Knives of the cutting mechanism should be sharply sharpened. To do this, they must be periodically removed and undermined. In a hinged position, it is forbidden to do this. Adjustment of the balancing mechanism is carried out after each fact of operation. Its spring part is checked and regulated.

Details of nodes subject to high friction are subject to regular lubrication. The conical gearbox, the section of the cutting timber and bearings, especially need it, especially. Lubrication is carried out only through the corresponding oil openings.

It is not recommended to pour oil or apply thick lubricating material in the rubbing areas not equipped with oil.liner traffic jams. This will lead to the sticking of dust and dirt in greased places, increase the degree of wear of parts and reduce their service life.

The procedure and list of works carried out for preparation for long.term storage is determined by typical characteristics. The main nuances of such preparation include cleaning of dust and dirt, removal of moisture from metal surfaces, coating parts with special anti.corrosion solutions. An important factor is the right choice of suitable storage location. It should be dry, protected from mold, drafts and other aggressive influences.

Additional information on how to prepare a rotary mower for the off.season storage is in the operating instructions from the manufacturer.

Look at the rotary mower on the Neva walk.behind tractor in action in the next video.

Modernization or refinement

The main disadvantages of any braid that can be bought at the store are:

• insufficient strength of the structure;
• insufficiently rigid fixation to the walk.behind tractor;
• ineffective sharpening of knives;
• ineffective lubrication of rubbing parts;
• insufficient ski length;
• lack of defense of the operator;
• the impossibility of comfortable movement.

To increase the rigidity of the structure, pipe and other elements are welded to the braids on the bolts that remove excessive mobility of the frame. If the standard mount does not provide enough rigid fixation of the attachment equipment to the chassis, then it is redone, eliminating all the backlash. The method of alteration and refinement depends on the design of both devices.

The standard knives have no notes, so instead of them are used by homemade dampers, sliced ​​from old sickles or knives of various agricultural machines, and then balanced so that vibration does not appear after installing them. Reducers are often supplied with gearboxes without sufficient lubrication, especially often this happens with Chinese and devices.

In order not to disassemble the gearbox each time, a tawnnik is cut into its side or upper wall from a car, for example, gas 2410, then once a month or season through it is served a suitable lubricant.

Facial devices equipped with standard skiing are well suited for even areas, however, where there are pits of various sizes, their lengths are not enough, so the braid can fail, which will lead to a damage to the knife and possible breakdown of the shaft. Therefore, those who are forced to mow grass in uneven areas welcome extension cords to standard skis, so that the mowing passes without incident.

Almost all braids are deprived of the operator’s protection, so a stick or stone that came under a knife can injure you.

To avoid this, stretch behind the plates under the engine of a target from a tarpaulin or durable linoleum.

Parts of the owners of such devices do not like to walk for a long time, so in addition to the hitch, the mowing is attached to the walk.behind tractor, turning the device into a self.propelled machine. After such an alteration, even the mowing of huge areas is not difficult, because the operator does not have to follow the mower on foot, because he controls her while in the cart’s seat.

Rotor haymaking and the price of them

We recommend that we buy a rotary mower to agrarians who need to mow a dry diameter of less than 100 mm, thick vegetation or hard residues of sunflower or corn. But the rotary model will cope with the departure of the lawn or a small area in the garden. Aggregate to the drive of the Neva motor block in front or trailer method. The trailed traps mulch the grass, so they are not suitable for farmers that need herbal harvesting on hay.

The operation of the rotary mower is carried out from the belt shaft of the walk.behind tractor. Suitable for Neva motor blocks on gasoline and diesel moves, as in the video. For attaching to the latter, a special adapter includes a complete set. Among the various rotary mowers for Neva, Kaluga Zarya and St. Petersburg KR-05 stand out. Depending on the modification on rotary mowers, 1-2 working discs, the KR-05 working body 1, the “dawn” has 2 disks. On the disk using a moving hinge connection, 4 knives are fixed. The movable codder when the disk moves allows knives under the influence of centrifugal force to turn around and they cut the grass. The Dawn Disks rotate towards each other, the width of the handling of the lawn is larger. The design of the rotary model on special sledges is located, they allow a simple movement to adjust the height of the cut of grass. Small vegetation in even shafts is distributed in two sides and it is easy to assemble it with a pitchfork.

It’s easy to work with a rotary mower, but once a day it is necessary to spin the corner joints and smear the gears with a lithol or machine oil. The technique will last with proper care longer.

Consider the popular segment models for the Neva motornote Read more on video and photo. In the video below you can see how the equipment works on the field and along the road.

Rotary “dawn”

Official manufacturer of the Dawn Rotor Rotor Pitch. “Kadwi”. is located in Kaluga. But the market has many home.made and Chinese models made according to the manufacturer’s schemes “Kaluga Engine”. Outwardly, they differ only in color-at the Kaluga Dawn it is bright red, as in the video. But this is not the main difference. Chinese quality is worse, since low.quality material is used for manufacturing.

The official “dawn” for the Neva motornote showed itself in use well. Chinese and homemade mowers are just fakes, although among them you can find models of acceptable quality.

Characterization of the haying “Dawn” for the Neva walk.behind tractor and the price of analogues and licensing equipment in the table:

You can buy cheaper directly from the manufacturer in Kaluga. The retail price is 10-15% higher and it is more profitable to buy in bulk. Spare parts from the domestic model are suitable for all Chinese analogues, therefore, in some cases, you can not overpay. The price of used equipment starts at 5,000, but we do not recommend purchasing equipment over 10 years old.

Rotor mower of KP.05

Officially, KP-05 is produced in St. Petersburg at the Krasny October factory. The model is official to the Neva MB-1 and MB-2 motornote. It is impossible to find accurate analogues in the market, but there are similar mowers with low quality. Many years of experience and advanced technologies allowed the manufacturer to develop an optimal, functional and small rotary mower KP-05. Read more Model in the work, the reader can consider on the video.

The weight of the technology is smaller than the Zarya model, so the KP-05 is convenient for summer residents and farmers with small personal sections. Copes with any remnants of cultivated plants, shrubs, hard and thick grass. The power of the crumbs is sufficient to cope with hard vegetation.

Kp.05 is used on an uneven surface, since the working organ in the form of a large disk is easily adjusted to any irregularities. Not afraid of a mower of small stones and branches. Around the disk is a metal casing that protects the operator from small particles of stones and vegetation.

Characteristics of the KP-05 for the Neva walk-behind engineer MB-1 and MB-2 and the price in the table:

Rotor.type mower

This equipment can be used for cutting the Luja, as well as to cut fresh herbal cover into hay. However, it is worth taking into account that such a haymaking hay of high vegetation cuts off, and low grass simply crushes small grass.

The main working elements of the device are knives, which are installed on the working discs by means of Shinka. The braid is driven by the power shaft, and sliding is carried out due to the rotation of the lower discs.

To make a rotary mowing frame with your own hands, you can use old metal corners or scrap metal, which is probably available on each craftsman. In order to save time for knives, you can use a tractor rotor. However, in this case, to improve traction and efficiency, it is advisable to reduce the length of the rotor from two to four centimeters, depending on the power of the unit used.

For the manufacture of the rotor, you need to make 2 round plates with a diameter of 390 mm from a sheet of metal or use the bottom for these purposes from an unnecessary tin barrel from machine oil. Exactly in the middle of these circles to weld the legs with which rotation will occur. The welded joint must be made durable.

For the lower support, you can take the disk from the luschtor, but its diameter should not be more than 450 mm. For the axial shaft, a pipe with a diameter not exceeding 30 mm can be used, and bearings 80, 106 will still be needed. On it to make a hole for attaching the lower bearing, and the second bearing is installed on the pulley. Put a device with knives on the axis, and then weld the pulley to the shaft. The rotation of the working discs will be carried out using two bearings.

Such a modification has a capture of 1100-1150 mm and the speed of rotation is 1500 about./min. The entire design of the braid is required to mount on the chassis boiled from a steel corner. For the safety of operation, it is necessary to install a protective casing on a homemade device. To simplify the structure, you can weld the lower drives of the rotary mowing on the frame by welding.

This homemade mower is able to cut off the vegetation cover at a speed of 8-12 km/h. At high speed, the grass is more crushed, and with a low one. integral. Such rotary type equipment can cut off vegetation 60-80mm and is used not only for mowing grass, but also for harvesting a personal plot from weeds.

Tool and materials

In order to make a completely functional and working segment mower with your own hands, you should take a metal pipe with a rectangular cross section of 1200x50x15 mm or a segment of a canvas of an ordinary braid for grass, and drill twelve 10 mm nests at an equal distance for the installation of m8 fasteners. Subsequently, they will be attached to a guide metal strip 890 mm long with teeth and knives installed from both planes of a rectangular pipe.

Knives have backs with segments and clips of a drive lever. On the pipe on both sides, clamps and scenes are also installed. The support wheel is mounted on the mowing chassis. The working part of the segment mowing is driven by the power shaft of the power of the power unit used.

Drawing of a segmented mower

Thanks to the use of a segment mowing, you can conduct high.quality bevel of fresh vegetation without its grinding. You can watch the work of the equipment in the video.

Dawn model 101

The uniform tractor dawn 101 represents a heavy class of agricultural machinery. This model is intended to perform the following operations: hilling, leveling and cultivation of soil, milling, plowing, interrelation processing of furrows, mowing, cutting of furrows, loosening, dialing root crops and others. The model due to high power is perfect for sections of up to 3 hectares.

Recently, fakes are regularly appeared on the market, masking for this brand. You can distinguish an original product by a special icon and technical characteristics. The counterfeit is characterized by a lower work resource and quickly fails, therefore, when buying this walk.behind tractor, you should be extremely vigilant.

The uniform tractor dawn 101 has a classic design with a large cast-iron lid, a protective casing on drive belts, an air-oily-oral battery air filter and a large mass. The model is equipped with a classic transmission with 6 front and 2 rear gears. The transmission of the motor.block dawn 101 has established itself on the best side on previous models. She is distinguished by high reliability and ease of work.

A 10.5-horsepower engine with increased performance is also installed on the equipment. Such a high power allows you to work with the soil of various compositions and transport massive goods.

Motoblock management is intuitive. The main elements are displayed on the steering hilt, therefore it becomes extremely simple to control the operation of the equipment. Despite the rather large dimensions and mass, the dawn model 101 is very maneuverable.

Design features of the walk.behind tractor:

• mechanical transmission of a mixed type, driven by the cylinder drive;
• ring brakes with sloppy blocks, providing rapid braking and safety when moving;
• The drive to the gearbox is performed by means of 2 wedge belts;
• The rear power shaft allows you to aggregate a technique with an active milling cutter;
• the ability to work in increased and reduced gears. The former serve for fast movement, the latter. for soil processing;
• The differential with forced blocking increases the maneuverability and cross.country ability;
• one.disc clutch of the friction type, which has continuous contact, makes the movement as smooth as possible.

The uniform dawn 101 in the basic configuration is offered with milling cutters, a set of tools, pneumatic wheels, instructions and a warranty coupon. The functionality of the equipment can be increased by buying additional equipment:

• mower;
• plow;
• potato.cutter;
• potato.resident;
• soils;
• special wheels;
• additional mills;
• cart.

Playing for the dawn of 101 is mandatory. It is performed quite simply and takes 8-10 hours. Bolter joints and fasteners are originally checked. Then the oil is checked and gasoline filling. After full preparation of the walk.behind tractor, the motor is launched and warmed up (no more than 5 minutes). If there are no deviations (subteces of oil, smoke and others) at this stage, then you should start work. In the first 10 hours, it is impossible to operate equipment at maximum power, limited to 65% of the maximum speed.

Features of the rotary model

Rotary mowers have a simple design, which facilitates their maintenance and repair. The working bodies are discs on which knives are mounted. They are fixed on the disks using movable hinges. Discs can be from one to several. The more working disks, the wider the area of ​​the processed surface will be.

The price of spare parts and components is low. For our models of rotary braids, spare parts can be bought at any specialized store. Imported models are not older than 10 years no worse. Mowers over 10 years of imported production may not have spare parts, since some models no longer release.

The owner of the rotary mower will easily ennoble the lawn in front of the house and stocks the grass for the winter for livestock. A small model for a walk.behind tract during cleaning areas around fruit trees and beds is convenient.

They produce rotary mowers with us, as well as abroad. Among the largest and most popular models, mowers for the Neva, Dawn, Mole, Favorite stand out. Models differ in the number of working bodies and adjusting the height of the cut of grass. To clean the grass for feeding animals, you can use models up to 20 cm high, haymaking with a cut height of 5 cm showed themselves well on the adjacent territory.

Aggregate with the Motoboblome Favorite, Mole, Neva Rotor mower in several ways:

Reviews are better about hinged models for the Neva and Cascade, Mole, Favorite. Their power is higher and it is easier to work with a walk.behind tractor, since the entire processed area is visible.

According to the method of mowing grass, rotary mowers are divided into views:

• For begging grass and laying in an even row. Suitable for mowing grass on hay.
• Mulching the grass. Crushed grass quickly rolls, suitable for handling lawns.

Selecting a model for its Neva, Salute, Zorya, Favorite, Mole is recommended to take into account the following factors:

Landscape features. The purpose of acquisition (for mowing grass on hay of livestock or for aligning the lawn in front of the house)

The weight of the mower (it is important during transportation, since it is difficult to transport a large model). Productivity (for a small lawn, the most miniature mower is enough with slight power)

Type of a bevel of grass (for harvesting hay for livestock feed, models that mulch grass are not suitable).

Zarya mower for the Neva MB-2, MB-1, MKM-3 Lander, Mole, Favorite

A hinged model of a small rotary mower has two working disks with knives on hinges. Produced in Kaluga at the machine.building plant “Kadwa”. Mows grass and folds it in one direction. Suitable for farmers that contain cattle. The model is light and has small sizes. Convenient in storage and transportation.

Dawn “dawn”

We will consider the technical characteristics of the “dawn” in the table:

It is suitable not only to the Neva and Mole, Favorite motor blocks, but also to small MTZ tractors with a horse force 10-12. The configuration of all manufacturers includes spare knives that provide uninterrupted operation of equipment in the season.

• Compactness;
• High performance;
• Low weight;
• Wide capture;
• Simplicity of design;
• Warranty from the manufacturer 3 years;
• Spare knives in the kit.

Zarya-1 braid

A special model from the Kaluga Machine-Building Plant “Kadwa” is designed for the NMB-1 Ugra, “Mole” motornote and the same with the same connection. The model has two working bodies with hardened steel knives. Convenient adjustment allows mowing in the fields with any landscape.

Rotor mower “Zarya-1”

The technical characteristics of the model are presented in the table:

Differs from the “dawn” by aggregation with a walk.behind tractor and high performance. The design has a weight, so the bevel of grass is more even. Suitable for small agricultural complexes. Aggregate with MTZ-80 mini-tractors. Easily copes with dry bushes, sunflower and corn.

Of the minuses, an insufficient number of service centers in the regions are distinguished.