Replacing the cord on the trimmer Elitek. Recommendations for stretching the strip spring

How to replace the launch cord of a lawn mower

Sooner or later, problems with the starter arise on any trimmer. Stihl FS 55, MTD 790 or other brand. You can delay the appearance of such a malfunction, but for this you need to carefully handle the tool. In particular, you should not make too sharp jerks, this will lead to a break in the cord or to the departure of the spring. It is not recommended to expose the lawnical mower by attacks or other physical influences. If the starter case breaks, and the cord breaks off, it can be wound on the engine flywheel. This will lead to a broken pulley and a bursting spring.

So, having discovered that the starter mechanism has broken on a gas station, you should not immediately rush for help to specialists. Knowing how the malfunction is eliminated and/or the details are replaced, repair work can be performed independently. This does not require any specific tool. At first, the procedure may seem complex and tiring, but numerous videos on the Internet devoted to the repair of the starter will help to solve the problem as quickly and simply as possible.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, it first needs to be disassembled, and then collect it. This process is not particularly complicated. You will need to work the shape of the screwdriver.

Everything should be done carefully, observing precautions, especially so that the spring does not injure the owner in case of accidental departure

Starting analysis

Disassemble the starter mechanism to install new parts instead of broken in the following sequence:

Unscrew the screw that attaches the pulley with the starter lid using a screwdriver; Remove the spring and antennae; Carefully remove the pulley (you need to turn your head or work, after putting on your glasses and gloves); Determine why the trigger worked; If the spring fell apart almost completely, it is replaced; Когда пружина выходит из крючка, она устанавливается на прежнее место, предварительно сгибая антенну (фотографии показывают процесс установки);

After the spring plate is installed inside the groove, carefully tighten it. To change the spring, the work must be performed carefully and accurately: it can accidentally explode under the influence of the force caused by its bringing into effect. Even if you carefully remove the video, the spring tape is very quickly torn off the coil and can injure the hand with sharp edges

Even if you carefully remove the video, the spring tape is very quickly torn off the coil and can injure the hand with sharp edges

To change the spring, the work must be performed carefully and accurately: it can accidentally explode under the influence of the force caused by its bringing into effect. Even if you carefully remove the video, the spring tape is very quickly torn off the coil and can injure the hand with sharp edges.

Immediately put in place a spring plate does not always work. This often slips, so attempts should be repeated to achieve the desired result.

Starter assembly

The assembly of the starting installation is carried out in several stages:

The coil turns over, installing it so that the bend of the spring accurately fits into the groove of the case, as in the photo below;

When making the above manipulations, it is necessary to put two goals. If this is not done, the spring will ultimately damage the plastic cup, and when it is removed, jamming will begin. This makes you feel that spring has come. To eliminate this drawback, it is necessary to install this part of a larger length or an additional goal.

When such details are not enough, you can just unscrew the screw a little, and the starter assembly will start working without fixing. But this option is temporary. It is better to repair it as soon as possible.

Spring tension

After installing the spring, tighten it. To do this, follow the following actions:

• Remove the handle from the starter cord;
• Then the rope is inserted into the groove of the coil;
• The spring is delayed by the rotation of the turn in the opposite direction clockwise (winding);
• Make the required number of revolutions specified in the operating instructions for the used trimmer model for grass, and the corresponding length of the cord used;
• At the very end, the rope is lowered into the hole provided for this, located in the starter cover;
• Place the handle in place by fixing it with a node.

Read what gasoline is pouring into the Husqvarna lawn mower

If after the repair the spring continues to fly, you can get rid of it in the following ways:

• Insert the corresponding piece of the plate into the groove at the location of the spring hook;
• Drill holes on both sides of the groove in the coil, into which you need to insert a spring hook and fix it with wire.

Replacing a torn cord

A torn cable is replaced in the following sequence:

• The old cord is removed;
• Choose a rope of a suitable size (thickness and length);
• Having passed it through a special hole located in the coil, tie a knot;
• Spring valve producing the required number of revolutions;
• Fix the pen

It is better to tighten the spring plate with Partner so that the edge of the cord does not twist inside the starter mechanism.

It is not difficult to assemble a starter on a trimmer and wound a spring, but this must be done carefully and carefully. For different models of gasoline engines, the breakdown of the starting mechanisms are the same, so they are repaired the same. However, there are some nuances associated with their constructive features

However, there are some nuances associated with their constructive features.

Repair of the starter of the gas tanker, lawn mowers, trimmers for the grass with your own hands

No matter how high.quality gasoline tools you use, everything can happen to it in the process of construction, and at the most inappropriate moment for this moment. Often problems arise due to the breakdown of the starter. It happens that you will get drunk with a gasoline hole for installing the fencing pillars or mowing the grass with a trimmer, you will start starting the unit, and just have time to pull the starter handle a couple of times, as the rope breaks off, and the engine has already started, dashingly wrapping the rest of the cord to the flywheel, the spring bursts run to the new store buy. But these, of course, are extremes.

Today we will consider the most common case when the breakdown is not so serious and show how to carry out the repair of the starter with your own hands if the cord has broken without any destructive consequences or is not wound due to the fact that the spring just flew inside, went out of the cloth. At least initially I want to believe in it. But in order to find out whether it is or not, you will need to disassemble the starter.

How to repair a starter of a benzo.tool with your own hands?

In the case of a break in the starter cord, everything is clear: we take out the old rope, take the suitable one along the length and thickness (you can linen), stretch it through the hole in the coil, tie the knot. Next, we take the spring to the number we need, only after which we fix the handle. and the voila! about how all this is done is clearly shown below.

Installing or replacing the starter of the starter motorcycles, motorcycle, trimmer for grass

But what to do if everything is in order with the rope, and the coil (pulley) of the starter is not wound? Consider this issue step by the example of the starter of the ADA Grounddrill gasoline motorized car, having a pulley with two metal antennae for 2 hooks.

In the case of other types of manual starters of the similar structure, which are widely used in gasoline motorcycles, trimmers and motorized carriers, the entire starter repair process will look similar, differing only in some nuances.

Starter repair: disassembly

Unscrew the screw with which the pulley is attached to the starter cover. We take out the antennae, spring. We pull the pulley itself carefully so that the spring does not bounce into the face. Even with the most neat disassembly, it usually immediately flies out of the coil and sharply turns into a long metal strip or twisted by rings.

Gently pull out the white.tolerator’s white coil. do not be wounded up by the spring!

If the spring burst or one of its hooks-stalks has broken, then it will not work out to repair the starter and quickly-it is necessary to replace the spring. In order not to spend money on the purchase of a new starter, you can look for only her on sale.

In case the starter spring simply fell off, t. e. One of the hooks came out of the hook, it is enough to insert it, if necessary, slightly tightening the hooks more tightly (just do not break off!) Install the spring with an external hook in the groove of the pulley and begin to twist it, while holding your fingers inside the coil and preventing it from jumping out of there.

Clutching the spring to the pulley, roll the spring in circular motion

It may not seem so easy to insert the starter spring from the first time, but everything comes with experience. Having trained a little, you can easily wrap the spring into the pulley in a maximum of a minute.

The winding of the starter spring is made. It remains only to assemble the starter and take the spring to the desired value

How to assemble a starter?

The most important thing in the process of independent repair of the starter is to collect it correctly.

After the spring is completely wound, you need to carefully turn the coil and insert into the starter case so that the second spring hook enters the groove of the case.

By installing the pulley (in this photo. black), look through the hole in it so that the spring hook gets into the groove on the starter cover

Then, if there is a spring under the screw, we install it first, not forgetting to put the washers from below and from above the spring.

Gently insert a cup with antennae into the grooves of the coil and tighten the screw.

Then keep sure that the puck is on the sprout does not fall. Why is it important? The fact is that the spring scratches a plastic cup with its end, as a result of which the latter wear out and begins to tightly pressed with a screw to the reel. For this reason, a situation may arise, very similar to the breakdown of the spring: the handle stretches out of the starter, but does not return back. However, when the starter is weakened, this problem disappears. It is easy to eliminate such a starter malfunction: it is enough to choose a spring of the same diameter, but a little longer, or put an additional washer. If we simply slightly tighten the screw, then it will be twisted and fly out, and this will increase the likelihood of a spring breakdown, since the pulley will not fit tightly with the starter case.

The coil to the body was screwed, now we need to pull the spring. Before this, it is necessary to remove the starter’s handle from the rope in advance. If the knot is too durable, then you can just cut it or try to untie it, for example, using a pair of pliers. This is done so that after you bring the spring, you can pass the rope into the opening of the starter cover. The second end of the rope should be fixed in the coil even before it is installed in the case, it is not required to be roped on the pulley before pulling the spring. you will do it after.

Before taking a spring, estimate how much the reel revolutions should be wrapped in a rope. Suppose the length of the rope at the starter of the Motor ADA Grounddrill-5 corresponds to 5.5 revolutions around the coil. In this case, we make at least 6 revolutions of the coil in the direction opposite to the direction of wiring.

So, let’s get down. Without wrapping, insert the rope into a groove specially designed for it in a coil. Everything is ready, proceed to pulling the spring. To do this, we rotate the coil counterclockwise. in the direction opposite the direction of rotation of the coil when watching the rope. It is more convenient to do this not on the knee, but pressing the starter with one hand to the floor, and the second turning the coil right behind the rope mounted in it. If the experience is not enough, then you can rotate with both hands directly the pulley itself, but the rope will interfere with it, which can create additional inconvenience. After the required number of revolutions is made, we spread the end of the rope through the hole in the starter cover, put on the handle, fix it with a knot. It is more convenient to do this together with a partner, so that the end of the cable does not hit the end of the starter by chance.

By the way, on your own, you can introduce some refinement to the design of the starter in order to more reliably fix the end of the spring inside the coil. There is enough fantasy here. Now I will explain what it happens for. It often happens that the spring in starters of this type after the first such independent repair and installation of the starter on the unit flies after a few jerks again. there is no hook in the groove of the coil. And this despite the fact that the coil is almost tightly adjacent to the starter cover and the spring there, well, should not even hang up and down freely, and even more so until the spring out of the gear. It turns out that when the cable is jerking, it pulls the spring, pulls out of the groove. In this case, you can make the following: cut a narrow strip of metal, which in thickness could squeeze closely into the groove of the coil with the hook itself. So the hook will not hang free in the groove, which means that it will not be so easy to break out.

The starter of the lawn mower jammed. How to repair a starter on a trimmer

A step.by.step annotation on how high.quality repair of the chainsaw starter is made with your own hands. Ordinary malfunctions. The procedure for starting the Ryobi lawn mower. Prerequisites for defects and their elimination.

High.quality repair of the chainsaw starter with your own hands

The chainsaw is the main tool with which you can stock up on firewood for a bath or fireplace, you can also use it when building work in a summer cottage or in a personal house. Subject to all the criterion of operation and conducting preventive measures provided by the manufacturer, the chainsaw can last a long time. But after the expiration of time, small malfunctions may appear, with which you can cope without the help of others. For example, the repair of the chainsaw starter with your own hands is completely possible, subject to the sequence of operations.

Starter of the chainsaw starter: 1- Starter screw, 2 sleeve, 3 light starting spring, 4 screw, 5, 6 starter coil, 7 deflector, 8 starter cover, 9 handle and cord, 10 screw.

Typical malfunctions

The most common tools of the tool include the following:

• problems in the ignition system;
• stopping the chainsaw in the process of performing the sawing;
• loss of power during operation;
• wear of some structural elements of the chainsaw (brake tape, leading stars, anti.vibration parts);
• problems in the fuel supply system;
• malfunctions associated with the starter.

In addition, it is necessary to conduct a visual inspection of the chainsaw before starting work and preventive measures. These include the lubrication of the chain, control of the amount of fuel mixture, as well as the presence of the required amount of oil.

The spark plug is unscrewed to check its condition.

Each of the malfunctions is eliminated according to its technology. So, for example, the repair of the fuel system of the chainsaw should begin with the inspection of the corresponding filter. Failure to launch an electric lawn mower. After that, check the correctness of the regulation of the carburetor, which is carried out using screws. The gaps should be exhibited in strict accordance with the manufacturer’s instructions, which should be attached to the kit with a chainsaw. The repair of the spark plugs includes the repair of the ignition system. If a severe carrier is detected, a change in the clearance or other visible damage, this element should be replaced.

Starter repair work

Problems in the work of the starter may not ensure the launch of the tool. That is, after the cord is stretched, the chainsaw does not start to work.

Repair of the starter Motokos, trimmer for grass

Repair of the starter Motokos, trimmer for grass online store spare parts for garden equipment-

Family Brovchenko. Springing a spring in a hand starter of a lawn mower.

How to install a spring in a hand starter for a benzo-trimer? At home it is possible to do it. to me.

Before you repair the starter, you need to prepare the tools with which work:

• set of screwdrivers or a special tool that is attached to the manufacturer complete with the tool;
• a rope that will be used as a replacement of a broken cord if necessary.

A large amount of black carrier on the spark plug indicates the violations in the engine operation.

Before proceeding directly to the repair of the starter and clarifying the causes of malfunctions, it is necessary to remove it from the tool body. To do this, unscrew several screws holding the side cover to which the starter is attached. Problem with the installation of the Stihl 38 lawn mower starter. This is done by a screwdriver or a specialized tool.

After the lid is unscrewed, it is turned over and examined. Next, unscrew the screw with which the starter is fixed. After that, the clamp and the spring are dismantled to carry out smooth launch. Now for removing it is accessible to an affordable pulley on which the cord is wound. After the knot on the rope is unleashed, it can be pulled out of the pulley and replaced with a new. Provided that the loss of performance of the starter is associated with the cliff, this may be enough to eliminate the breakdown. Launcher. However, the rest that make up this element of the chainsaw should be carefully examined.

Elitek‘s lawn mower T750RK. Elitech T 750rc lawn mower

The Elitech T 750RK lawn mower is designed to care for the garden. D. The figurative handle provides ease of work in hard.to.reach places. A special casing provides the defense of the operator during operation. For the convenience of transportation and storage of braids for grass, a detachable bar is provided.

Packed goods parameters

Length, mm: 1000 width, mm: 260 height, mm: 260

Peculiarities

Advantages

• Light start;
• Shoulder belt reduces the load during operation;
• Tool for collecting and disassembling the kit;
• Centrifugal clutch;
• Vibro.gaming coupling.

Elitex lawn mower. Trimmers for Elitech grass (elitech): features, overview of popular models

The young company Elitech was founded in 2008 and became very popular among consumers. She is engaged in the production of garden equipment and related equipment, and almost the entire assortment is made in Chinese factories. Before entering the market, it passes multiple control.

Each Elitech mower is a high level of performance and power. It has all the features of European equipment, withstands heavy loads and has reliable components.

• Ability to withstand the largest loads.
• Reliable and correct assembly.
• Durability.
• Unpretentiousness in maintenance.
• Attractive appearance.

Trammers for elite grass can be used to mow grass in private household areas or for larger areas.

Consider the most popular company models.

Elitech T 26 lawn mower

One of the most powerful gas stones that can mow soft and hard grass. It works on the new type of engine, which withstands complex tasks. The elite model is supplemented with a soft handle, an shoulder strap. Due to its compactness, it is used in hard.to.reach places.

The Elitech T 26 gasoline trimmer can be launched on a cold engine. It also has a protective casing that makes the bevel safer.

Trimmer for Elitech et 1000 grass

Elitech functional and convenient electric cosse is designed to work in house territories, garden care. It requires a constant connection to power supply. It works with two cutting tools. the foot or fishing line.

Trimmer for grass Electric Elitech is equipped with a special protective casing. Can be used for a bevel of dry weeds.

Elitech T 52 lawn mower

A powerful trimmer for grass works even in areas of increased complexity. It is designed to mow very large thickets, young shoots of trees and bushes. Equipped with a shoulder belt and comfortable handles.

Elitech lawn mower operates without a break for several hours. It is not noisy and equipped with a protective casing.

Elitech T 43 lawn mower

Productive tool for effective mowing of weeds and grass. It works on a powerful engine and has a belt included for uniform distribution of the load on the back.

• productivity is 1.8 liters. With;
• Fuel tank. 0.9 l;
• work with fishing line and knife;
• bevel on width 25-44 cm;
• Weight. 9 kg.

Elitech lawn mower has a lightweight system. The tool handle is tuned to a convenient position. A protective casing is provided for a safer tool for the tool.

What to do if the engine does not start?

If the lawn mower fails is not possible, then the first thing is to check the presence of fuel in the tank and its quality. For refueling the tool, it is recommended to use high-quality gasoline purchased at gas stations, the brand of which should not be lower than the AI-92. Savings on cheap fuel can lead to a breakdown of the cylinder-piston group, for the repair of which a third of the cost of Motokosa itself can take. It is equally important and correctly preparing a fuel mixture of gasoline and oil. The proportional ratio of these components of the mixture is indicated by the manufacturer in the manual. Do not prepare the fuel mixture in large volumes, since during long storage its properties are lost. It is better to use a freshly prepared mixture.

When preparing the fuel mixture, pour the oil into gasoline using a medical syringe that allows you to accurately comply with the necessary proportion of the components

Fuel filter pollution in the tank may also prevent the operation of the lawn mower engine. Therefore, when problems with the launch of the motor, check the condition of the filter. If necessary, replace the filter. It is forbidden to leave the incoming pipe without a fuel filter.

The air filter also needs to be in the test. During contamination, the part is removed, in the field is washed in gasoline and put in place. In the country or at home, the filter can be washed in water using detergents. After that, the filter rinses, squeezes and dries. The dried filter is moistened with a small amount of oil used to prepare the fuel mixture. Excess oils are removed by compressing the filter with hands. Then the part is installed in place. The removed cover is placed back and fixed with screws.

The air filter washed in the fuel mixture, squeezed and dried, is installed in place in the plastic case and covered with a lid

How this procedure is done in more detail you can look at

If all of the above procedures are carried out, and the engine is not started, then adjust its revolutions at idle, twisting the carburetor screw. In the video posted at the beginning of the article, attention is paid to this issue.

• Put the tool on the side so that the air filter is at the top. With this location of the chainsaw, the fuel mixture is ensured exactly into the bottom of the carburetor. On the first attempt, the engine will start if you remove the air filter before starting and pour a few drops of the mixture into the carburetor, and then install the dismantled parts to the place. The method is tested in practice.
• If the first advice does not give a result, then, most likely, the problem in the spark plug. In this case, unscrew the candle and check its performance, as well as dry the combustion chamber. A candle that does not show signs of life, replace the new.
• If the spark plug is in good condition, the filters are clean and fuel mixture, then you can use the universal way of starting the engine. Close the carburetor air damper and pull the starter handle once. Then open the damper and pull the starter 2-3 times. Repeat the procedure from three to five times. The engine will surely start.

Some pull the pen with such force that it is necessary to repair the starter of the lawn mowed with their own hands. This is possible only in the case of a gust of a cable or breakdown of the cable handle. In other cases, it is recommended to replace the starter. This node is sold in the collection.

How to replace the spark plug correctly?

As you can see, there is nothing superplousing in this procedure.

A new spark plug for a two.stroke internal combustion engine of a gasoline braid for grass is installed in return for the old detail that failed

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work, you will need a screwdriver with the tip of the desired shape.

Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.

Parsing the starting node

They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:

• spin a screw with a screwdriver, fixing the pulley with a starter lid;
• take out a spring and antennae;
• Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
• determine why the launch mechanism has broken;
• If the spring collapses almost completely, then it is replaced;
• When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);

To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst. Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges.

Immediately putting a springy plate in the same place does not always work. It often slips, so attempts are required to repeat until the desired result is achieved.

Starter assembly

The assembly of the starting node is carried out in a number of stages:

When making the stated manipulations, it is necessary to lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled. Because of this, a feeling appears, as if the spring had flown. To eliminate such a drawback, you need to install this part of a larger length or an additional goal.

Spring tension

After installing the spring, it should be pulled. The following actions are performed for this:

• Remove the handle from the starter cord;
• Then the rope is inserted into the coil groove;
• They stretch the spring, rotating the coil in the direction opposite to the clock of the clock arrow (reviews);
• make the desired number of revolutions specified in the instructions for the use of the trimmer model used and the corresponding length of the cord used;
• At the very end, the rope is threaded into a hole designed for this, located in the starter cover;
• put the handle in place, fixing it with a node.

If after the repair the spring continues to fly, then you can get rid of this in the following ways:

• Squeeze the suitable piece of the plate into the groove at the location of the spring hook;
• drill holes on two sides of the groove in the coil, into which the spring hook is inserted and fix it using a wire.

Replacing a torn cord

A torn rope is replaced in the following sequence:

• The old cord is removed;
• choose a suitable rope (thickness and length);
• Having reached it through a special hole in the coil, a knot is tied;
• Sprinkle a spring, producing the required number of revolutions;
• Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way. In this case, there are some nuances associated with their constructive features.

Review: gasoline trimmer for the grass “Forester 304”. Good, reliable, tested by time.

The fight against grass in the garden is one of the main troubles, there is one that can be pulled out or rolled, but there is grass for which you need, something serious At the current time, a wide selection of lawn mowers (trimmers) is presented, both electronic and gasoline. Electronic comfortable in calling, but the radius of their deeds is limited by the length of the cable and if there is a need to “fight” with the grass far from the outlet, it is better to use a gasoline trimmer. How to change a fishing line for a trimmer in dry grass just due to a trimmer for an electric grass. When buying a country assistant, his own choice was made in favor of a gasoline trimmer for the Forester 304 grass, the production of the assembly of Chinese comrades, by the way, did not cause any shakes. How did you choose a fishing line for a trimmer for how to change a fishing line for a trimmer I have an electric trimmer for grass de. The choice in favor of a portable trimmer for grass was also made due to the need to mow not only lawn grass, and a large weed (wormwood, burdock) on a relief area where the mobile apparatus was. would not be in place.

Replacement of fishing line on a motorcycle.

How to wind the cutting cord to the coil of motorcycles (trimmer for grass)

The gasoline is manual. All details in the article How to change a fishing line for a trimmer to a forester.304 “(bought a fishing line for a trimmer for a trimmer for grass as. Replacement of fishing line in a reel.

The principle of operation is simple, first we prepare the fuel mixture, dilute the special oil,

intended for two.stroke engines, with AI gasoline. 92 in a ratio of 1:50, refill and go.

Review

The Forester company is a subsidiary of the Gardentrailing holding. This organization has been supporting domestic manufacturers for more than ten years. Lesnik products are one of the youngest in the garden tools and technology markets. In addition to maintaining the domestic market, Gardentraining adapts the products of little.known in foreign companies. Despite the fact that this trademark is little.known, many buyers prefer it in contrast to other domestic manufacturers.

Garden technique TM Forester is represented by electric and gasoline tools in T. h. trimmers. Most of this brand benzocosyles are designed for domestic use. It is worth noting that many companies acquire a forestry technique to ennoble park zones, public places, and t. D.

The main malfunctions of the coil

Users of electric trimmers and black cutters often face the problem of semi.automatic mowing. Coil malfunctions can be as follows:

The fishing rod does not extend automatically

If the fishing line for the trimmer is not lengthened by the light touch of the trimmer button for the grass to the ground, the causes may be the following.

Option 1. there was a bite, that is, a clamping cord between turns. This problem usually occurs if the user wraps the coil unevenly, crossing the coils, or starts it with insufficient voltage. In the latter case, when the head of the braid rotates at high speed under the influence of centrifugal force, the cord begins to contract, which leads to a possible twisting of a braid fishing line of hair growth. To eliminate the problem, you will have to disassemble the coil on the trimmer and correctly rewind the cord, that is, even spins with good tension.

Option 2. too short ends stick out of the head. A shock fishing rod may not appear when hitting the ground if its protruding ends have insufficient length (short). In this case, centrifugal force is not enough to stretch the fishing line for the trimmer. Therefore, it is necessary to stop the unit (turn off the engine or disconnect the electric trimmer for grass from the network) and manually stretch the fishing line for the trimmer, first pressing the button.

Option 3. Fishing line for a trimmer of hair is soldered inside the head of a mowing head. This makes the coil stop and do not rotate when you press the button. This is mainly due to several reasons: the poor quality of the cord, the overheating of the coil with continuous operation of the unit, the effect of a mowing fishing line on hard objects.

• In the first case, a third.party cord can be made of low.quality and fusible materials that do not withstand mechanical and thermal loads. Therefore, preference should be given to “branded” fishing.
• But if you are still acquiring an unknown quality of the cutting element and it often stumbles during operation, you can follow the example of some users who, after you wrapped a cord in a coil, moisten it or silicone grease (from a spray can) or mineral oil). This procedure significantly reduces the likelihood of soldering the coil of the wire.
• In addition, it can be soldered if it is stuck in a solid object (stone, fence, dry branch, etc. D.) During the mowing. As a result, it is slightly stretched and diverted back to the head at high speed. The cord is heated due to friction, and its coils stick together. The only thing you can do to eliminate problems is to open a trimmer to the grass and rewind a fishing line for a trimmer.

The cord spontaneously lengthens

There are times when the user of a trimmer for grass notices a very quick consumption of a cutting element. Nevertheless, he never pressed the button on the ground to extend the fishing line for the trimmer. The reason for the unintentional lengthening of the cutting element, cutting off a special knife on the device case, may be a lack of spring in the head of a mower. Often users-novice-toe, trying to load the hair fishing line for a trimmer into a reel, forget to install a detained spring in their heads or even lose it when the lid opens, and in the future they do not even know about its existence.

Types of trimmer heads

A mowing head for grass is a cylindrical case in which a coil (bobbin) is inserted with a fishing line in it (cord). This design can be installed both on gasoline and electric trimmer. The heads differ in the method of refueling and supplying the cord and there are 3 types.

• Automatic. The cord is supplied after the user reduces engine speed. Although the automatic supply of the fishing line is convenient if large volumes of work are performed, such rods have one drawback. a large thread consumption.
• Semi.automatic. Using this type of head does not require complicated manipulations from the user. The principle of their operation is arranged so that the cord is automatically lengthened at a time when the device works at full speed. It is enough to slightly hit the trimmer’s head for the grass on the ground (this removes the cord lock), and the fishing line for the trimmer, due to the centrifugal force, moves out of the bobbin, after which it is cut to the desired length with a knife located on a protective casing.
• Manual. For lengthening the cord, the device is required, after which the fishing line for the trimmer is handed out manually.

Based on the above, semi.automatic bobbins are the most optimal option. It should also be borne in mind that the coils for a trimmer for grass are one.built (used only to trim the grass) and two.string, which are used to mow high grass and small, with thin stems of shrubs.

Method 2. two segments

fundamentally no different from the method.The only difference is the two wound segments of the fishing line, instead of one.

There are two special fixing nests on the coil (see drawing above).

How to replace the fishing line for a trimmer in a mowing head, coil of the motorcycles Stihl FS 55

They hook it previously formed on the fishing line, and begin to wrap a fishing line for a trimmer.

Winding is carried out in a special order

The winding needs to be carried out in the following order: first the lower fishing line for the trimmer, t.e. that which is closer to the fixing holes at the bottom of the coil, and only then the upper one, t.e. the one that will overlap the lower section.

The tips are made in the holes of the corps of the rogue trimmer for the grass. They are pulled to a click, which means that the fishing line for the trimmer

The tips are torn into the holes of the corps of the rogue trimmer for the grass

The coil is fastened into the case. Lines for a trimmer

The main parameters of the trimmer fishing line

Fishing lines can be classified according to the following parameters:

The thickness of the thread

You can find out about it by reading the operational characteristics of the trimmer for the grass or focusing on the size and inscriptions on the universal bobbin. Typically, threads with a diameter of 1.2-4 mm are used for trimmers. True, for each device you will have to select a fishing line for a trimmer of a certain diameter.

A thread for a trimmer for grass, thinner than the required, the engine will not disable immediately, although it will significantly increase its wear. If you use the thread thicker than necessary, the resistance of rotation will increase, the engine will operate more intensely, overheat and, as a result, will break. True, a lot depends on the engine itself.

You can find out the approximate diameter of the fishing line for the type of engine. If a trimmer for grass works from electricity or battery and its power is 1 kW, you need a cutting thread with a diameter of 2 mm, and if its power is less than 500 W, a fishing line for a trimmer is not more than 1.6 mm for a trimmer.

For a gasoline trimmer for grass, a fishing line for a trimmer is chosen with a certain diameter. 2.4. 3 mm. The choice of such a thick fishing line is associated with the features of gasoline units. they are more powerful and productive than their electrical counterparts. You can operate a thick fishing line for a trimmer for a long time, in addition, it will easily overcome a long.term dry.

The composition of the fishing line

It is the composition that determines the life of the fishing line. Often it is made of nylon. It slowly wears out and increases the efficiency of performance at high temperatures and high loads. The material retains its working properties for a long time, low temperatures do not affect it, as well as prolonged work.

The fishing line for the trimmer of the coaxial group for trimmers is considered one of the strongest. It has a dense core, and therefore wears out gradually. Such a fishing line for a trimmer is difficult to cut with a knife and when working creates little noise. Also now there is a fishing line for a trimmer, which includes intersperses of aluminum.

The shape of the section

Most often select a fishing line for a trimmer for electrocos with a round section. It is inexpensive and the most popular, sprinkles fresh grass well. Its main disadvantage is in the published level of noise, which is heard during the work of the trimmer for the grass. The noise of the fishing line is close to the engine hum. For the best noise use, manufacturers offer to use a fishing line for a spiral trimmer.

Today also releases a fishing line for a trimmer of a square section for a trimmer for grass. Of other forms, quite often rectangular and starry. Particularly productive fishing lines with zazubins and sharp edges are. Such faces cut the grass more evenly.

There are also options for fishing line with notch and dents. They can download large weeds. The noise level published by such a fishing line is low, and due to the increased properties of aerodynamics, the trimmer is given additional power. Such a cutting element is installed on powerful trimmers for the grass, which are planned to carry out work in overgrown, neglected areas.

To work with a fishing line of this type, special heads are installed on the motorcycle. A fishing line for a trimmer is wound on them. She copes with herbs of any kind (especially weeds) and shrubs. But its cost is quite high. The consumption of such a fishing line is also high, since when serving from the coil, difficulties can arise with its extraction. It is usually used with disks in which it is inserted in small segments.

There is also a two.component twisted trimmer fishing line for a trimmer. Its purpose is a high.quality mowing of dry. It is distinguished by a round section, resistance to ruptures and increased strength. It comes with the core produced from other material. Twisted fishing line for a trimmer is suitable only for gasoline trimmers. She is able to cope even with small shrubs. Its main drawback is the high cost. For daily work, purchasing a twisted fishing line for a trimmer is enough.

How to repair a starter of a benzo.tool with your own hands?

Installing or replacing the starter of the starter motorcycles, motorcycle, trimmer for grass

But what to do if everything is in order with the rope, and the coil (pulley) of the starter is not wound? Consider this issue step by the example of the starter of the ADA Grounddrill gasoline motorized car, having a pulley with two metal antennae for 2 hooks.

In the case of other types of manual starters of the similar structure, which are widely used in gasoline motorcycles, trimmers and motorized carriers, the entire starter repair process will look similar, differing only in some nuances.

Starter repair: disassembly

Unscrew the screw with which the pulley is attached to the starter cover. We take out the antennae, spring. We pull the pulley itself carefully so that the spring does not bounce into the face. Even with the most neat disassembly, it usually immediately flies out of the coil and sharply turns into a long metal strip or twisted by rings.

In case the starter spring simply fell off, t. e. One of the hooks came out of the hook, it is enough to insert it, if necessary, slightly tightening the hooks more tightly (just do not break off!) Install the spring with an external hook in the groove of the pulley and begin to twist it, while holding your fingers inside the coil and preventing it from jumping out of there.

Clutching the spring to the pulley, roll the spring in circular motion

It may not seem so easy to insert the starter spring from the first time, but everything comes with experience. Having trained a little, you can easily wrap the spring into the pulley in a maximum of a minute.

The winding of the starter spring is made. It remains only to assemble the starter and take the spring to the desired value

How to assemble a starter?

After the spring is completely wound, you need to carefully turn the coil and insert into the starter case so that the second spring hook enters the groove of the case.

Then, if there is a spring under the screw, we install it first, not forgetting to put the washers from below and from above the spring.

Gently insert a cup with antennae into the grooves of the coil and tighten the screw.

Then keep sure that the puck is on the sprout does not fall. Why is it important? The fact is that the spring scratches a plastic cup with its end, as a result of which the latter wear out and begins to tightly pressed with a screw to the reel. For this reason, a situation may arise, very similar to the breakdown of the spring: the handle stretches out of the starter, but does not return back. However, when the starter is weakened, this problem disappears. It is easy to eliminate such a starter malfunction: it is enough to choose a spring of the same diameter, but a little longer, or put an additional washer. If we simply slightly tighten the screw, then it will be twisted and fly out, and this will increase the likelihood of a spring breakdown, since the pulley will not fit tightly with the starter case.

Before taking a spring, estimate how much the reel revolutions should be wrapped in a rope. Suppose the length of the rope at the starter of the Motor ADA Grounddrill-5 corresponds to 5.5 revolutions around the coil. In this case, we make at least 6 revolutions of the coil in the direction opposite to the direction of wiring.

A metal plate, tightly inserted into the gap between the hook of the spring and the walls of the groove, will reliably hold the spring

Recently, along with a chainsaw, one of the main assistants in the household has become. a gasoline trimmer for grass (lawn mower). Over time, owners of inexpensive Chinese models may encounter a number of breakdowns. In the article, we consider the most common trimmer malfunctions for grass and methods for their elimination. We hope you share information in the Комментарии и мнения владельцев.

Primary diagnosis of a trimmer for grass.

The proper operation of the engine and the lawn mower in general is affected by a huge number of factors that are usually interconnected. If you fail to determine the malfunction, contact the proven service center.

I would like to note that before proceeding with disassembly and serious repair, you should check elementary consumables. These “little things” often affect work and, perhaps, repair of a trimmer for grass will cost “small blood”, so to speak.

Fuel filter. lack of pollution, mechanical damage, good throughput. Periodic replacement according to the maintenance schedule in the operating instructions

Air filter. lack of sawdust and pollution. Periodic cleaning in soapy solution and purge under high pressure. Replacement of the air element according to the instructions for the expulsion

Let’s get acquainted with other possible malfunctions:

It is worth noting that many owners confuse air leaks with a malfunction of the carburetor. Symptoms of air leaks into the engine are a strong oversuance of revolutions, both short and constant. Or a braid for grass simply refuses to start.

The device and principle of operation of the starter on the trimmer

The gasoline engine is, in principle, the main part of the motorcycles its power lies in the range of 0.5-2.5 liters.With. The movement from it is transmitted by the shaft located inside the hollow bar, and then through the gearbox, consisting of gears, already a fishing line or a knife (working body).

Also, the lawn mower has the following elements:

• protective casing;
• lever;
• a belt designed for ease of use of the device;
• Starter serving for launching a gasoline internal combustion engine.

All parts of the motorcycles are presented in the photo further.

The starter on the trimmer is an integral part, which performs the engine starting into operation. It is shown separately in two photos below.

The starter mechanisms of various models of the benzos work according to the same principle: during the launch of the ICE, the protrusions marked in the photograph above the number 1 are included in the hook with dogs 3. When the engine begins to work, they return to their previous position due to the effects of centrifugal. Similar role is also played by wires 2.

The process of returning to the initial position of the elements of the mechanism occurs due to the presence of a spring screwed around the axis. It unfolds when the rope is pulled. After releasing the cord, it is drawn and winding due to folding the spring. During the launch of the ICE of the lawn mower, the triggering mechanism turns its shaft until it starts to work (starts).

To date, gasoline motorcycles are equipped with two types of starter mechanisms:

The first option is much more common.

The starter on the trimmer can function without breakdowns for a long time. It is impossible to unambiguously indicate the deadline. Everything is determined by the initial quality of the device and compliance with the rules of handling it.