Stihl adjustment of oil supply to the circuit. General disadvantages

Stihl 180 oil supply to the chain

The main prerequisites for which oil is not supplied Stihl 180.

The fuel system of the chainsaw: 1. Fuel filter, 4.5. carburetor, 3. manual pump preparatory pumping.

Unhurried reduction in fuel consumption during the service life. Ordinary process. If it is absent, chain It is not true, so working with a chainsaw will be fine. It is necessary not only to be able to eliminate breakdowns, and to identify them without the help of others.

It is possible to manually change the fuel consumption. The correctness of the lubricant complex of accounting programs is determined by the way of bringing the tire. If the oil spray occurs, then what remains to do to our client is correctly configured.

During the operation of the chainsaw, it is necessary to look at the lubricant of the chain all the time. Since this part works in the most languid criteria. Chain subject to invariable overheating, dust and abrasive particles are clogged there. This is poorly affected by his service life. A special lubricant will allow to correct the situation. Submitted to the chain from the tank, which provides uninterrupted operation.

If there is no lubrication during operation, there is a large possibility of overheating. When the oil is not supplied, chain It begins to stretch. With all this, the possibility of its jamming or spontaneous jumping is preserved, and in the end, a person can get a languid injury.

The channels on which fuel is served can be clogged with small particles, therefore it is purposeful to clean them at times. Be sure to look at the oil level in the tank. Garbage in the duct. Frequent reason for the failure of the backwater brake. It may be bad for your work.

Consistent channel cleaning and the general service of the chainsaw will allow the tool to work for a long time.

The current state of the chainsaw can only be evaluated by special. In the absence of knowledge or uncertainty in one’s own strength, the repair of the tool is best entrusted to the specialist.

Real repairs on its own for lubricating the chain of the chainships on all equal aspects asks for knowledge of the interaction of all parts, which allows you to keep records (software), the presence of tools and abilities of the locksmith.

Restoring the performance of many chainsaws implies partial or complete dismantling of component equipment. It is better to use the abilities and technical potential of service workshops for complex repair work.

Parts with stripped threads and curved slotted compounds, also non.vegetable structures that are equipped with a lubricant system for lover of lovers of the STIHL 100 eighty and other models of the same type, change.

If when filling the tank, the oil does not fall into the design of the headset, the cause should be found in the pump itself. Dismantling and disassembling the mechanism help to identify faulty parts and remove the malfunction, replacing them.

Considering the types of defects in the lubricant system, two categories can be distinguished:

General breakdown of all types of power units;
Personal ones that depend on the type of pump, on the features of the worm transmission, on the structural other features of a certain chainsaw.
The chain mechanism is dry, pale, there is no shine;
The chain was rapidly stretched after installation;
The guide tire heats up, the paint melts on it;
The oil remains in the tank in the same volume, despite the rich operation of the tool;
The effectiveness of chain cutting is significantly reduced.

Stihl MS390 | Engineering an Oil Pump

If the consumables arrive, then the reason for the problematic operation of the lubricant node is most likely lies in the clogged filter, which can be cleaned or changed to new. By ability, after this manipulation, the supply of consumables is regulated.

If the consumable has not been received, then it is necessary to conduct additional diagnostics, because, most likely, the inconsistent is more serious.

Keep in mind that you do not always need to dismantle the bus to check the lubricant system. As an option, the end of the tire is directed to the side (use the pillow) from the direction of the cut, maximizing the speed, hold the tire (its end) at a distance of 10 cm from the pillow. You will see proper points when supplying oil.

The main malfunctions of the chain saw oil system can be divided into two main types: these are common difficulties inherent in all chain saws, and individuals that may vary depending on the type of pump and worm transmission installed on a specific model. Let’s start understanding the dilemmas in order.

Criteria for choosing lubrication

After buying a device, the question may arise about choosing a bay in a stihl chainsaw. After all, proper care for technology increases its performance, and will save various kinds of breakdowns. The operation of the saw directly depends on the use of good fuel and lubricant.

STIHL chainsaws have a carburetor two.stroke engine and 2 tank (gasoline and oil). For the right choice of oil for the STIHL saw, you need to know its criteria:

It is necessary to determine the manufacturer, t. to. In domestic models, simple oils (for motorcycles) are used in a proportion of 1 to 25, and foreign. branded lubrication products, with a proportion of 1 to 40 (oil proportions to gasoline). In fact, the owners themselves determine what to use. It is worth being prepared that improper use will entail a decrease in power and productivity. Most use motor oil, if this is not, then the transmission. Experts advise for this manufacturer to use the last.
You need to know the color. Red, green, blue colors are suitable for chainsaws with a two.stroke engine.
Compound.

The main reasons why STIHL 180 oil does not come

Self.repair of the Stihl MS 180 chainsaw. The chain of chainsaws is not lubricated. We find and eliminate the cause of the Samos.

The first thing that needs to be done after suspicions arose that the oil lubrication does not come, it is to check its feed. Diagnosis of the lubrication system of the chain of the chain of the chainsaw of the chainsaw STIHL MS 180 frequent. You can do this in two ways. The first is described in detail in the instructions for the tool and is that you need to start a chainsaw, add the gas as much as possible and directed towards any obstacle.

Stihl chainsaw does not enter the carburetor gasoline

With a good lubrication system, the oil will fly from the tip of the tire and on the surface, in the direction of which the tire is directed, a strip of oil drops will appear. If there are still violations in the system, the surface will remain clean.

The second way is to remove the tire from the chainsaw and start it. With an increase in the engine speed, at the place of installation of the tire shank, oil will come from the oil channel, if this does not happen, it is necessary to look for the cause of the malfunction.

The device of the lubrication system

Depending on the brand of the chainsaw, the details of the lubricant can differ a little structurally, but their total number and connection scheme remains unchanged.

The main components of the details of the lubrication system are:

Oil tank located, as a rule, in the engine crankcase.

Oil supply adjustment to the Partner chain chain

How to repair oil supply to the chainsaw

In the process of prolonged work of the chain saw, some of its elements and components can become unsuitable. One of the most vulnerable components is an oil pump. In this regard, many owners of saws have the question of how to repair a supply of oil on a chainsaw.

The task of the oil pump. apply grease to the chain. This is necessary for its smooth movement along the guide. When the oil pump is destroyed, the lubrication of the chain worsens, and therefore the effectiveness of the chainsaw is reduced. In some cases, this leads to a rupture of the chain. To prevent negative aspects, it is necessary to repair oil supply in a timely manner. How to do it?

The principle of operation and the device of the pump

Oil pumps can be made of metal and plastic. They are also divided into two types that differ in their design:

The pump is activated by the drive of the leading star. When the chain moves, the oil is supplied to a special channel located on the guide. At idle (when the leading star does not rotate) the pump does not provide a lubricant supply. This is done to save.

The speed and volume of the lubrication of the lubricant into the circuit directly depend on the number of revolutions of the asterisk. Some models of the chainsaws include a manual adjustment system with a special screw located on the device case. On expensive models, the oil supply is automatically regulated during operation.

The main problems with the supply of oil

During the operation of a chain saw, two types of problems are possible when applying lubrication to the chain:

Partner chainsaw does not open the oil on the chain.

In this video, we will examine in detail the power pump Partner chainsaw, find out why Partner is not a chainsaw.

How to adjust the oil supply to the chainsaw

Someone can use my first channel:.

Insufficient oil consumption, which can be caused for various reasons. If measures are not taken on time, the quality of work will noticeably deteriorate, and the scheme itself can become completely useless.
Excessive amount of oil. In this case, after long work under the saw, you can collect puddles from fat. This not only affects oil consumption, which will need to be constantly poured, but also negatively affects the environment.

Both of these problems must be eliminated as soon as possible after their detection. This will extend the service life of the saw and reduce the consumption of lubricant fluid.

Correction of problems

If the oil enters the chain in excess amounts, not only during the saw, but also at idle, it is necessary to perform manual setting (if the pump design provides this possibility). This is done using a screw, which is located on the case near the guide, usually from below or from the side. Tightening the screw, the oil supply is reduced, and the weakening. vice versa. If adjustment does not help, it is necessary to check the performance of the pump, as well as inspect the tire. Perhaps, at the place of its connection with the body, a gap is formed through which the oil flows past the circuit.

The lack of oil can be caused by several reasons, for each of which there is a solution:

A malfunction of the oil pump. As a rule, it consists of unsuitable masonry. To replace it, you must carefully disassemble the pump so as not to damage its moving parts. Then a new gasket is installed, after which the pump is mounted and installed in place.
Damage to the oil wire hose. If the pumping of the pump is in order, or its replacement has not led to the result, check the tightness of the hose. If it is faulty, it must be replaced. Otherwise, it will not be superfluous to clean it and fix it with a sealant.

If the reason is not related to the failure of the pump, it is necessary to check all the conductive holes and channels for blocking and, if necessary, clean them of extraneous objects. It can be done by a stream of compressed air.

Do not want to contact a chainsaw, but you need to adjust the flow of oil? Seek for help to our specialists who will diagnose and repair the chain saw, and if necessary. adjust and adjust the lubrication level. Your saw will be the same new!

Dismantling of the carburetor if it is necessary to check or repair the components

The device of different models of carburetors is almost the same, so when working with them you can use the standard scheme. All elements must be removed carefully, and then lay out according to the order below, so that it can be successfully placed in place at the end of the repair work.

The upper cover is removed. To do this, unscrew 3 bolts that hold it in a circle.
Foam is also removed, as it is the upper component of the filter conducting the air.
The fuel hose is removed.
The drive of the drive is displayed immediately on it.
The cable tip is disconnected.
The gasoline hose can be completely removed if you are systematically pulled off from the fitting.

To finally prepare the carburetor for major repairs or replacement of the smallest parts, you need to carefully disconnect it from the main system. Sometimes its further disassembly is required. The constituent elements should be unscrewed and fold the fasteners in groups, since these small details are easily lost.

How to repair a chainsaw

To repair a chainsaw, you need to familiarize yourself with its internal device, the operation of all mechanisms, and study the system for feeding the lubricant. When the chainsaw works, the following problems may occur.

Often a leak of oil fluid is often observed.

Perhaps the tightness of the hose attachment is impaired. To solve this problem, you need to make out the tool, to replace the hoses. If there are no spare parts, you can degrease the old hose and its seat. At the place of connection of the hose with the tube, mount self.tightening clamps. The field of this tightness will be restored.

Read also: How to call the starter winding

Sometimes the oil filter is clogged. It must be periodically cleaned. The supply of oil is repaired only in the case of a dry circuit. This is usually due to clogging of the channels. They must be careful careful. This phenomenon is very common.

When it is difficult to start a chainsaw, and sometimes it is simply impossible, it is required to diagnose the apparatus. First, candles and air filter are checked. Before repeated installation, all parts need to be well dried.

The fuel system of the chainsaw: 1. fuel filter, 2. carburetor, 3. manual pump pump pump.

If you have fuel candles, we can talk about its excess. The main reason for such a problem is poor carburetor adjustment or incorrect launch. Perhaps the fuel supply crane is closed. To eliminate the breakdown, you need to make sure that there is enough fuel in the gas tank, check how well the combustion chamber functions. If the candles are unusable, they must be replaced.

Perhaps the supply of fuel has stopped due. A vacuum forms in the gas tank, which blocks the fuel supply. This phenomenon occurs when the channels are clogged, the carburetor is poorly configured and the air filter clogged. These problems require valve repair, which levels the pressure during gasoline supply. Sapun is cleaned with a sharp needle.

To adjust the carburetor, you need to find the optimal speed value. To do this, it is necessary to turn up or, conversely, turn out, adjusting screws. This setting should be performed exactly according to the instructions for repairing the chainsaw of STIHL.

A filter network is cleaned in the carburetor, all channels are blown, the operability of the membrane is checked, no gaps are allowed.

Work with a carburetor due to its complex mechanism should be carried out carefully and in perfect cleanliness. Its normal and good work depends on this.

To achieve good operation of the chainsaw, you must constantly care for it. It requires constant cleaning of the air filter, lubricant of the circuit, and always with new, fresh oil.

When the tool is cleaned for long.term storage, it is necessary to drain all the gasoline and remove the oil for lubrication of the chain. In this case, the chainsaws will work without breakdowns for a long time.

Malfunction of the pump and system as a whole

As you know, there is nothing eternal in this world and over time everything has to be repaired. So the STIHL MS 180 oil system is no exception, and has its own specific malfunctions. Consider them in more detail.

Signs of malfunction of the lubricant system, as follows:

The chain of the chainsaw is absolutely dry and does not shine;
Oil from the oil tank does not leave;
The chain is quickly stretched and this happens constantly;
The saw of the saw takes away when sawing, to the side;
The tire is warming up in the area of the leading star, melting paint is observed.

All these signs, directly or indirectly indicate problems in the lubrication system of the chain of the chainships.

The first thing that needs to be done after suspicions arose that the oil lubrication does not come, it is to check its feed. You can do this in two ways. The first is described in detail in the instructions for the tool and is that you need to start a chainsaw, add the gas as much as possible and directed towards any obstacle.

Diagnostics

Diagnostics should begin with the inspection and check of the oil receiver (filter) of the STIHL 180 saw. As a rule, if the filter is very contaminated, oil supply may stop.

In order to save, a clogged filter, you can try to clean it, washing it carefully in gasoline.

Next, it is necessary to remove the drum asterisk, and check the condition of the lead gear. The thread on it should be clearly expressed, not licked and not to have any other defects, also with the gear removed, it is necessary to check the wire lever. He must squeeze the gear tightly and not turn, otherwise, the gear stands still and does not transmit the effort to the pump, as a result of which the oil supply stops.

If all of the above methods to detect and eliminate the malfunctions did not give results, it is necessary to apply extreme measures, t. e. dismantle the pump.

How to remove the pump

The oil pump is installed on the right side of the bottom of the case, in the same place the oil pipeline coming from the tank of the chainsaw is suitable for it. To remove the pump, you will first need to free the saw from the handle, for this the rear handle of the unit is spent and the thrust of control of the throttle is disconnected. At the next stage, you need to remove the plugs of the shock absorbers of the handle and with the help of a powerful slotted screwdriver, squeeze them out of their seats on the handle.

The reason for the appearance of fuel oils on the bottom of the chainsaw

The Stihl 180 chainsaw has a characteristic malfunction, which consists in insufficient sealing the place of installation of the oil hose in the chainsaw case and the appearance of leaks in this place. To eliminate it, it is enough to remove the handle of the STIHL MS 180 saw, disconnect the hose itself, rinse and degrease the seat in the case and the tail of the hose, and then apply the sealant, and set the hose to the place. Such a simple operation will reliably eliminate the malfunction and the oil will cease to leak.

Stihl ms 180 oil supply adjustment

Of course, each of us wants to buy a quality chainsaw that would be reliable, durable, economical and with good technical characteristics. All these criteria are fully consistent with the Stihl MS 180 chainsaw. We will talk more about its advantages, general breakdown and self.healing.

Calm MS 180 Chainsaw device. Accessories

Stihl MS 180 chainsaw design is difficult to call simple. This is due to the features of this model. Calm 180 chainsaw device consists of the following components:

Ematic Guide;
Oilomatic proprietary chain saw;
Air filter;
throttle;
Cold and hot starter lever;
Control lever;
Spark plug;
Pen with its own vibration suppression system,
Powerful motor with an increased service life.

The manufacturer took into account the possibility of regular operation of the chainsaw at low temperatures, which led to the presence of its own system for a smoother and fast start of engine.

Calm MS 180 chainsaw. specifications

In terms of performance of the chainsaw of the Stihl MS 180, it is much superior to analogues in its price range. This tool and its modification. SHTIL 180 C chainsaw has the following technical characteristics:

Power. 2 l. from.;
The volume of the cylinder is 31.8 cm3;
Fuel consumption. 0.7 l / hour;
The volume of the fuel tank. 250 ml;
The volume of the oil tank is 145 ml;
The speed of idle. 2800 rpm;
Launch guide;
Lubrication of the chain. automatic;
The length of the tires used is 30-35 cm;
The step of the chain. 3/8 ‘
Working weight. 4.2 kg.

Read how to change a fishing line for a trimmer on a trimmer STIHL FS55

Calm MS 180 chainsaw does not require special care. The only thing the owner needs. it is to use high.quality fuel and add oil in a timely manner. The diameter of the file for sharpening the chain of the chain of the stihl MS 180 should be 4.5-5 mm.

Features of the Stihl MS 180 chainsaw

This model of the chainsaw, as well as its modification. Calm MS 180 C BE, not difficult to use. Below we will consider the basic rules of operation that will protect the basic details and mechanisms of the chainsaw from premature wear.

How to dilute gasoline for Calm 180 chainsaw?

The chainsaw engine should work on a properly prepared mixture of gasoline and oil. The higher the quality of these two components, the longer your garden tool will work. The ratio of oil and gasoline is of great importance.

How to launch a Calm 180 chainsaw?

The correct procedure for launching the chainsaw is as follows:

The chain brake should be activated before starting the saw. To do this, the brake lever must be tilted forward;
Next, remove the protective cover;
Then click the decompression valve. This will facilitate the start of the engine;
Then click the fuel pump several times. This will reduce fuel consumption directly when the saw engine is launched;
Then set the lever combination of the throttle to the cold launch. To do this, you must first activate the gas lever;
Pull the cable slowly until you feel resistance. Then quickly pull the cable to you until you hear how the engine starts and stops;
Then move the combined lever to one position up;
Pull the cable again until the engine starts;
As soon as the engine starts, press the trigger and release the combined lever until full;
Let the lever of the backwater brake, pulling it over until you hear a characteristic click;

How to break the new Calm 180 chainsaw?

Starting with the Stihl MS 180 chainsaw, most tool owners do not know how to crack the purchased dust correctly. To do this, follow the following actions:

Check the oil. Put the saw on the old newspaper and run the tool. If there is oil, traces of oil will appear on paper;
Then turn off the inertial brake;
Then start the chainsaw and let it work for 20 minutes. In addition, short starting pressure is required every minute;
After 20 minutes, start cutting thin branches, gradually increasing the density and diameter of the wood.

Read Battery from an electric screwdriver does not charge

Calm 180 chainsaw. malfunction and repair

In the case of a chainsaw, the Stihl MS 180 malfunctions and the methods of eliminating them can be different. To independently repair the Stihl MS 180 chainsaws, consider the most common causes of breakdowns and ways to eliminate them.

The chainsaw is not started. Reasons and repair

If you notice that your saw has stopped working, this may mean that the engine oil fills the light of the instrument. To inspect the candle, remove the rubber cap from the body and unscrew the part using a wrench for a candle. If you see large oil spots on a candle, this means that the cause of the breakdown lies in it.

Stihl MS 180 chainsaws do not work

The most common cause of this is the improper adjustment of the carburetor saw. If the saw does not work at idle, you need to reconfigure the assembly of the tool. To do this, remove the adjusting key from the set of saw and insert it into the screw “on the instrument handle. During this, slowly turn the screw clockwise until the saw starts to work correctly.

Gasoline is not supplied. Independent solution to the problem

This is due to the malfunction of the carburetor. This will need to be disassembled to repair the device. However, before disassembling the carburetor on the Calm 180 chainsaw, be sure to disconnect the throttle of the throttle from it and the ignition wire. Further actions are as follows:

The carburetor node is attached to the design of the saw with 4 screws. Unscrew them and remove the saw disk assembly. Before removing the carburetor, be sure to put on gloves so that your hands do not get dirty;
Before cleaning the carburetor, you will need to apply a household degreaser to its walls. Wait 5 minutes and start wipe the assembly walls;

Oil supply to the chain of the chain of the Stihl 180 chain

Construction and cottage in an understandable language

Repair supply of oil chainsaw STIHL 180

Each year, the technique becomes more perfect, which greatly simplifies the works of modern workers.New improved models arise on the market everywhere. Why flies a candle in a chainsaw.

For the latest disassembly of the chainsaw of Stihl 180. But at least a tool asks for appropriate care. STIHL 180 chainsaw is no exception.

In this article we will talk about how to correctly repair this tool.

Repair of the chainsaw STIHL 180

In order to correctly carry out repairs, you should deal with the internal mechanism. This rule applies to at least a tool. Let’s see the more popular difficulties that may appear when working with a chainsaw.

one.Owners often encounter a leak of oil, which usually lubricates the chain. It is necessary to remove the flywheel of the chainsaw of the Stihl 180 carburetor from the chainsaw. This may be a result of a bad density at the points of connection of the hose from the oil tank and pump.

To remove this case, the tool should be disassembled. Then you need to check the connections and if necessary change the hose to a high.quality analogue.

Read adjustment of the Husqvarna chainsaw carburetor

If you cannot purchase a new hose, you should remove the old one and degrease the landing site and the hose itself. After which you need to install self.tightening clamps, which firmly provide the density of the compounds. Such an approach will decide this case.

Apart from this, it is recommended to check and clean the oil filter.

Stihl 180 oil supply repair

STIHL 180 Oil supply repair should be carried out if you saw that your chain is dry. Closely inspect the channels on which the oil is supplied and perfectly clean them. Channel clogging occurs quite often.

Diagnosis of the lubrication system of the chain of the chain of the Stihl MS180 chain

Self.repair of the Stihl MS 180 chainsaw. The chain of chainsaws is not lubricated. Dismantling the chainsaw of Stihl 180 Part 1 Vasiliy. Dismantling the chainsaw of the Stihl 180 chainsaw we find and eliminate the cause of the Samos

For better clarity, we recommend that you view the Stihl 180 Repair of oil supply video.

STIHL 180 Oil Production Repair Video Instruction of the user of the chainsaw of the Stihl MS180

If the saw does not start, you should carry out a thorough diagnosis of the tool. First you need to check the air filter and the performance of the candle. To do this, it should be unscrewed and dried.

Read how to check the spark plug on the chainsaw

If the fuel mixture is found on the candle, then there is an excess of fuel. Chain (14 ″; 1.3 mm for STIHL 180 14 Rezer PS-9-1.3-50 low price, chainsaws (536. The reason may be a poorly adjusted carburetor or violation of launching rules. See if access is opened by gasoline.

To do this, open and close the gas tank cover. It is also necessary to check the combustion chamber. After the work done, check the service of the candle and change it if necessary.

Description of the common malfunctions of the Stihl 180 chainsaw and ways to eliminate them. The cause of the breakdown may be clogged sapun. Here I tell and show the proportion of mixing oil and gasoline for the chainsaw of the Stihl MS 180.

Not only telling but also show. Thus, when working in a tank with fuel, a vacuum forms, which affects the supply of fuel.

This can happen due to an unresolved carburetor, the clogging of its channels or air filter.

To fix the problem, you should repair the valve, thanks to which the pressure is aligned when fuel is supplied. To do this, the sapun should be carefully cleaned with a needle.

Read how to assemble a one.legged tractor with your own hands from a chainsaw

To adjust the carburetor, you need to use three screws. the largest and most small revolutions. Adjustment should be carried out strictly according to the instructions for the repair of the chainsaw.

Remember that the carburetor is a very complex device, since it consists of many small parts, so it should be approached very responsibly to it and disassembly.

If you want a saw to work properly, you should constantly care for her. Do not forget to clean the air filter in a timely manner and lubricate the tool chain with only clean oil. With prolonged storage of the tool, it is necessary to remove gasoline and oil for the circuit from it. Then the saw will serve you for a very long time.

Stihl ms 180 oil supply adjustment

Calm MS 180 Chainsaw device. Accessories

Stihl MS 180 chainsaw design is difficult to call simple. This is due to the features of this model. Calm 180 chainsaw device consists of the following components:

Ematic Guide;
Oilomatic proprietary chain saw;
Air filter;
throttle;
Cold and hot starter lever;
Control lever;
Spark plug;
Pen with its own vibration suppression system,
Powerful motor with an increased service life.

The manufacturer took into account the possibility of regular operation of the chainsaw at low temperatures, which led to the presence of its own system for a smoother and fast start of engine.

Calm MS 180 chainsaw. specifications

Power. 2 l. from.;
The volume of the cylinder is 31.8 cm3;
Fuel consumption. 0.7 l / hour;
The volume of the fuel tank. 250 ml;
The volume of the oil tank is 145 ml;
The speed of idle. 2800 rpm;
Launch guide;
Lubrication of the chain. automatic;
The length of the tires used is 30-35 cm;
The step of the chain. 3/8 ‘
Working weight. 4.2 kg.

Features of the Stihl MS 180 chainsaw

How to dilute gasoline for Calm 180 chainsaw?

How to launch a Calm 180 chainsaw?

The correct procedure for launching the chainsaw is as follows:

The chain brake should be activated before starting the saw. To do this, the brake lever must be tilted forward;
Next, remove the protective cover;
Then click the decompression valve. This will facilitate the start of the engine;
Then click the fuel pump several times. This will reduce fuel consumption directly when the saw engine is launched;
Then set the lever combination of the throttle to the cold launch. To do this, you must first activate the gas lever;
Pull the cable slowly until you feel resistance. Then quickly pull the cable to you until you hear how the engine starts and stops;
Then move the combined lever to one position up;
Pull the cable again until the engine starts;
As soon as the engine starts, press the trigger and release the combined lever until full;
Let the lever of the backwater brake, pulling it over until you hear a characteristic click;

How to break the new Calm 180 chainsaw?

Starting with the Stihl MS 180 chainsaw, most tool owners do not know how to crack the purchased dust correctly. To do this, follow the following actions:

Check the oil. Put the saw on the old newspaper and run the tool. If there is oil, traces of oil will appear on paper;
Then turn off the inertial brake;
Then start the chainsaw and let it work for 20 minutes. In addition, short starting pressure is required every minute;
After 20 minutes, start cutting thin branches, gradually increasing the density and diameter of the wood.

Calm 180 chainsaw. malfunction and repair

The chainsaw is not started. Reasons and repair

Stihl MS 180 chainsaws do not work

The most common cause of this is the improper adjustment of the carburetor saw. If the saw does not work at idle, you need to reconfigure the assembly of the tool. To do this, remove the adjusting key from the set of saw and insert it into the screw “on the instrument handle. During this, slowly turn the screw clockwise until the saw starts to work correctly.

Gasoline is not supplied. Independent solution to the problem

The carburetor node is attached to the design of the saw with 4 screws. Unscrew them and remove the saw disk assembly. Before removing the carburetor, be sure to put on gloves so that your hands do not get dirty;
Before cleaning the carburetor, you will need to apply a household degreaser to its walls. Wait 5 minutes and start wipe the assembly walls;

Adjusting the chain tension on the chainsaws of different brands with your own hands

The algorithm for setting up the chain tension for chainsaws of different manufacturers is almost the same. On some chainsaws, the procedure is slightly different, but first we consider the general principle of setting the degree of tension of the headset.

Initially, it is necessary to make sure that the tool needs to set up the degree of tension. Having pulled the headset from the tire in the upper part, you must make sure that the shank protrusion does not exceed a distance of 3-6 mm. Do not forget that measurements and manipulations for setting should be carried out on a cooled tool, and only at a positive ambient temperature.
If the chain has a significant stretch, then it is not subject to adjustment. Such a headset must be replaced or repairs by removing several links.
Chainsaws are located on a table or other even surfaces. This is necessary to increase the convenience of the procedure. When work is performed in the forest, it is clear that taking a table with you for this is not necessary.
Weaken the tightening of two nuts with the key on the “13” tire mount. over, this weakening should be insignificant. no more than half of the turnover.
The front of the tire must be raised up the plane, holding in this position.
Next, we find an adjusting screw, the location of which on different models of tools may vary, but it is located mainly next to the tire connection with the chainsaw building. This screw must be rotated to adjust the tension of the cutting headset.
The rotation of this screw is carried out using a screwdriver or a hexagonal key, which also depends on the shape of the hat. Moving the screw clockwise helps to increase the tension, and in the opposite direction weakening is carried out.
In the process of rotation of the screw, it is necessary to check the degree of tension by pulling the chain from the tire in the upper part. As mentioned above, the value of the output of the shank of the link should be no more than 6 mm.
The cutting headset is also checked by manually moving along the tire. It should move easily and without making physical effort. Когда оттягивается цепь, и выступ хвостовика составляет 6 мм, но при этом гарнитура тяжело перемещается вручную, то необходимо еще ослабить ее натяжение.

As soon as adjusting the degree of tension of the cutting headset of the chainsaw is performed, it is necessary to tighten the tire fastening nuts. The adjustment procedure ends on this, and you can start working as a tool.

Interesting to know! The adjustment of the chain tension on the chainsaws must be carried out not only during the operation of the tool, but also when the aggregate of the run.in process passes.

A visual example of how to adjust the chain on the stihl chainsaws shown in the video below.

What kind of oil to fill in the Stihl 180 chainsaw (Stihl 180)

Remember personal safety while working with a chainsaw.

Remember that the quality of the poured oil affects the work of the chainsaw. Advantages of the Husqvarna chainsaw 240 why gasoline from the chainsaw “Husqvarna” 240? Low quality oil can cause the instrument ineffective work and negatively affect its details.

In order for the STIHL MS 180 oil pump to supply oil without difficulty, periodically check and clean the pump. Oil flows from the chainsaw oil leaks. Brief review why oil in a chainsaw. Thus, the process of supply oil will be normal.

Oil lubrication oils. which is better and how to use?

Chain chainsaw. a tool equipped with a two.stroke carburetor engine. For high.quality and long.term operation of the chainsaw, it is necessary not only fuel. gasoline, but also lubricants, that is, oil. All technical oils, regardless of the principle of action and the scope of use, serve as one goal. the quality of the engine, lubricating the leading parts of the motor, the durability of details, and a decrease in the degree of wear of details.

The perfect oil for lubrication of the chain of the chainsaw should meet the following requirements:

Being a high.quality, preferably, a known world brand or “family”, which is produced by the manufacturer for its chainsaws; have good adhesive properties, that is, evenly and tightly distributed throughout the area of the chain and the place of contact of the chain with the bus; comply with viscosity standards for the season; not to be smoke.forming; withstand low temperature and do not freeze in frost, which is especially important for working in the winter season.

How to use oil lubrication oil chain?

To supply lubrication to the chain in a chain chainsaw or electric saw, a special pump is provided. Using this pump, the oil should be supplied directly to the tire, distributed along the chain, contributing to the quality work of the tool. The degree of oil consumption directly depends on the number of engine speeds. the higher it is, the greater the consumption.

Oil supply adjustment to the Partner chain chain

Most modern oil pumps of chain chainsaws are arranged the same: in the case (photo 1 pos.1) the cylinder is posted (photo 1 pos.2) into which the plunger is inserted (photo1 poses.3), performing in it rotational-setting movements.

The cylinder in the lower part has two holes (in the photo 1 pos.4 shows only one of them): through one oil it is sucked, in the second is pushed out.

A plunger is a steel rod, on the one hand it has a milling back. a bald, and with a second plastic or steel gear. When the plunger rotates, the bald alternately opens and closes the intake and exhaust holes of the cylinder. With the progressive movement, the bald first opens the inlet (while closing the exhaust) and creates a slight decrease in the pressure. Due to this, a portion of oil is sucked into the cylinder. Then, turning, the plunger moves down, opening the bald hole (while closing the intake) and pushing the oil out of the cylinder. So it is served on the bus in small portions. Due to the high frequency of cycles, a constant and continuous flow of lubrication is created.

Two types of oil pumps are used: with an adjustable supply of oil flow and with an unregulated feed. In the first case, the plunger gear has an oblique tooth, and the progressive movements are provided with an additional installed spring. Oil flow regulation is carried out by changing the length of the plunger in the cylinder. Example-oil pump for Chinese saw with engine volume 45-52 cubic meters.cm

In the case of an unregulated oil pump on the plunger, there is a slanting closed groove into which the motionless emphasis of the case rests. Rotation leads to sliding grooves by cut, and since it is oblique this movement forces the plunger to walk forward backward. With such a scheme, it is impossible to limit the perek of the plunger and the oil is served in constant quantities. Example. Husqvarna chainsaw oil pump 137, 142

The rotational moment from the engine to the plunger is transmitted through a special drive, which also has a gear. the response part of the gear on the plunger. In fact, this is a worm couple. The oil pump drive is driven by either the leading sprocket of the chain (photo 4 poses.1), or the crankshaft itself (photo 4 poses.2).

In the first case, the plunger is mechanically connected with the leading star and rotates only with it. In the photo 4 poses.1 STIHL MS-180 chainsaw is presented. Steel Usik clings to a special back on a cup of a leading asterisk. When the asterisk rotates, the drive rotates with it. There is no oil supply at idle in this case.

1.25 part DESTROYED a Stihl MS 362 oil pump. If your chainsaw bar is not oiling, check this out.

In the second case, the drive is rigidly fixed on the shaft and constantly rotates with it. In the photo 4 poses.2 shows the oil pump of the chainsaw of Husqvarna 137, 142. He attacked the shank of the crankshaft and rotates with it constantly. Therefore, the oil is supplied constantly, even if the saw is in idle mode.

Typically, one of the gears (either on a plunger or on the drive) is made plastic in order to protect the part with a more complex design or complex installation. The first part of plastic will break and worn out.

On some saws, the oil pump with a drive can be additionally closed with a special lid (photo 5, the oil pump cover of the Chinese chainsaw 45-52 cubic meters.cm), which protects the worm connection and the pump itself from the ingress of dirt and wood dust. On some saws, such as Husqvarna 137, 142, the oil pump itself closes the connection of the drive with the plunger, thereby performing the function of the protective cover.

For normal operation of the tire and chain, a certain amount of lubrication is required.

Preventive work on the maintenance of the chainsaw

Sharpening of the saw is performed independently by means of devices and a file or on a machine machine. It is made when the cutting edges, minor chips on the teeth.

Filters change is carried out periodically in accordance with the recommendations of the manufacturer. Air, oil and fuel elements are subject to renewal.

Replacing the spark plugs is performed after a certain time, guided by the requirements of operation.

Fuel gas station. Different manufacturers and engine type determine the composition of the fuel mixture-2 or 4-stroke gasoline engine is seasoned with gasoline with or without oil additive.

complex work is the repair of a piston group, gearbox, clutch, etc. P are carried out as events. Such work is usually carried out in specialized repair shops.

Correctly configured chainsaw is a guarantee of safe and high.performance work. Remember this!

Description of the device and technical parameters

STIHL 180 has a standard configuration. However, like all modern chainsaws. Its components:

Front and back handle with anti.vibration system.
Sawing tire with a chain.
Two.stroke single.cylinder engine.
Fuel and ignition systems.
High.quality plastic case.

STIHL 180 chainsaw, technical characteristics:

A gasoline engine that works on a mixture of fuel and oil in a ratio of 1:50.Has a power of 2 liters. With.

Sources:

https://101benzopila.ru/stil-180-podaca-masla-na-cep/
https://veloelektro.ru/STIHL-180-ne-smazyvaetsya-tsep-video.html
https://101benzopila.ru/kak-otregulirovat-podacu-masla-na-cep-benzopily/
https://cooptech.ru/drugoe/benzopila-shtil-techet-maslo-cepi.html
https://lesaegais.ru/regulirovka-podachi-masla-na-benzopile-shtil.html
https://veloelektro.ru/regulirovka-podachi-masla-na-tsep-STIHL.html
https://molibden-wolfram.ru/regulirovka-podaci-masla-na-cep-STIHL/
https://domdetaley.ru/regulirovka-podaci-masla-na-cep-STIHL/
https://pridesaratov.ru/drugoe/smazka-benzopily-shtil.html

Articles adjustment, circuit, stihl, supply