The trimmer for the grass grasps and stalls a raw candle. The second is a carburetor

trimmer for grass does not start a candle dry

By means of air filter, the incoming air is cleaned into the carburetor. The clogging of the cleansing element leads to the fact that the air enters in a smaller quantity or its supply to the carburetor is completely stopped. Find out whether the air filter is the reason that the trimmer for the grass is not started is in a simple way:

• Remove the air filter and inspect it. The presence of clogging is already a reason to blame this detail in everything
• If there are no clogs visually, then you must try to start the motor without a filter. If a trimmer for grass starts without a filter, then it is definitely necessary to replace this part
• The air filter can be cleaned with a stream of compressed air, but if it has not changed for a long time, it is advisable to replace it with a new

It should be noted that the lawn mower may not earn due to blocking the air filter, but these are extremely rare cases. Often, clogging of the air filter affect the stability of the engine, and also help reduce performance.

Important! If the chainsaw began without an air filter, then it is contraindicated to work as a tool without a filter element, since pollution will fall into the cylinder, and thereby, the operational resource will decrease. The real reason why the gasoline trimmer for grass is not started is to clog the fuel filter

This part is located in the tank of the tool, and if the spit is already more than 2 years, then it is time to check the serviceability of the fuel element. If the filter is clogged, then the fuel mixture, respectively, will not enter the carburetor, which means that the trimmer for the grass will not start

The real reason why the gasoline trimmer for grass is not started is to clog the fuel filter. This part is located in the tank of the tool, and if the spit is already more than 2 years, then it is time to check the serviceability of the fuel element. If the filter is clogged, then the fuel mixture, respectively, will not enter the carburetor, which means that the trimmer for the grass will not start.

Difficulties, with the replacement of the fuel filter, do not arise, since, for this it is enough to extract this part from the tank, and to replace it. If you are going to clean the fuel filter with a compressor, it is recommended to abandon this venture. It is better to buy a new filter for cleaning the fuel of the lawn mower, since, there will still be clogs inside the old element.

If you are not sure that the reason for the impossibility of launching a trimmer motor for grass is a cleansing element of fuel, then the following actions should be done:

• Remove the fuel filter
• Run the lawn mower
• If she started, and quickly, then really, is a problem in the fuel filter

The reasons for the clogging of the fuel filter

• With prolonged operation of the tool
• If low.quality gas or oil is used
• With prolonged storage of fuel in the tank of the tool
• If you pour fuel into the tank, which was stored for a long time
• When dust and small particles get into the tank of the tool. This usually happens during the tooling

Important! If the fuel filter is serviceable, and the lawn mower is not started, then it is worth making sure that the fuel hose is placed in the fuel. After all, there are times when the hose, along with the filter, is simply disconnected from the trunk tube, which leads to the impossibility of starting the engine engine

In the next publication Profidom.com.UA will complete the consideration of malfunctions of a lawn mower or a trimmer for grass, because of which they may not start

Checking filters

Another common cause, due to which a trimmer for grass does not start, is the presence of a blockage in the filter area. To confirm the conjecture, just dismantle the indicated block and try to start the unit without it. If the engine of the trimmer for the grass has launched, most likely you will have to replace the air filter or at least perform a thorough purge of the old. In the presence of abundant contaminants on the surface of the filter element, it is necessary to use a new grid. Relying to such actions, you should not leave a suction pipe at all without a filter. After all, rush in this case can lead to the need to repair the entire piston group of the unit engine.

If the step-by-step algorithm for searching for a malfunction has not given a result, and your braid for grass still does not start or stalls, it is worth examining the carburetor and the engine itself. A clogged carburetor can become one of the reasons, unstable operation of the tool. Three main problems can be distinguished here:

• Clogging of channels or nozzles. All this is cleaned with special flushing or blown by a powerful stream of compressed air from the compressor. Do not use needles and wire, so the passing sections can be damaged;
• Wear of the carburetor laying. Output. replacing the failed laying;
• Violation of tightness. To check this indicator, you can use the usual household tonometer, replacing the pressure gauge on it with the right. Follow the testimony: if they do not change, everything is fine, and since the pressure will begin to fall, then some part of the carburetor is faulty. Will have to find it and replace it with a new.

If everything is in order with the carburetor, then the gasoline trimmer for the grass may not be launched due to wear of the piston group. If chips, scratches or bully are found, on the piston or cylinder they should be replaced. Piston rings are subject to mandatory verification. A small rally piston when swaying the connecting rod indicates that the time has come to change the rings. This procedure is best entrusted to the specialists of the service center.

Diagnosis of the filters of the lawn mower

Another reason why the gasoline braid for grass stalls is an air filter. To exclude it, try to remove the filter and start a trimmer for grass without it. If it turns out, then you will have to change the air filter to a new one, or at least blow and carefully clean the old.

You can’t start a gasoline trimmer for grass due to contamination of the fuel filter. This is the next stage of our algorithm. Here we check the state of the filter element and, if necessary, change it with the new. When replacing, try not to leave a suction pipe without a filter, this is prohibited by any operating instructions. Rush can turn into the repair of the piston group of the engine.

Close in the muffler

Before resorting to more serious repair actions, you must make sure that the graduation channel is serviceable. This section does not apply to previously not used trimmers, since they have practically no production. If the lawn mower is operated for many years and during this time the unit was not subject to serious diagnostic measures, then it is necessary to check the fact of the clogging of the muffler.

The accumulation of soot prevents the exhaust gases from going out, which is why it is simply impossible to start the engine. Of course, on one day the graduation channel cannot clog, which is why such a situation should be preceded by certain signs. The exit of black smoke from a silencer is a kind of incapacity, which gradually accumulates on the walls of the exhaust system. A significant increase in the sound of the installed motor may occur, which is associated with overcoming huge resistance with exhaust gases to release them. When working at idle, the device stalls spontaneously. In critical situations, the engine operation is significantly deteriorated.

If there are serious pollution on the anti.skill net, then the reason for the impossibility of starting a trimmer engine may be precisely in the final channel. You need to clean the mesh as carefully as possible, since it is the black cargo that is a carcinogen that is very dangerous for a person, which can provoke damage to the respiratory tract. For cleaning, specialized tools should be used that will cope with the soil.

Main reasons

As practice shows, gasoline trimmers for grass cease to start or function normally after winter, that is, long.term seasonal storage. Before subsequent attempts to launch the tool, a thorough diagnosis should be carried out in order to determine the source of problems. There are currently several of the most common causes of malfunction.

• Initially, it is necessary to check the quality of the fuel. Savings in such cases may have extremely negative consequences. Experienced owners of Motokos and experts advise preparing a mixture, the volume of which will correspond to the upcoming work, since its surpluses quickly lose their qualities.
• Trammers for grass of such eminent brands, such as, for example, Husgvarna, Makita, Stihl, are very sensitive to the fuel used. We are talking about fuel quality and octane number. Ensure suitable operating conditions and extend the life of the equipment will allow the refueling with high.quality gasoline.
• At the time of the launch of an internal combustion engine, the lawn mower can stall due to the fact that it floods the spark plug. Often in such situations you have to deal with the need to configure the carburetor. It is worth noting that similar problems arise when a braid for grass stops starting on a hot.
• Sometimes the tool cannot be launched, although the candle is wet, which in turn indicates the intake of the fuel mixture into the combustion chamber. As a rule, this is one of the symptoms that there is no spark. The reasons may be the absence of normal contact between candles and a high.voltage wire or drying out the threaded connection in the candle channel.
• If there are no problems with a spark, and at the same time the candle itself remains dry, then most often this indicates that gasoline is not downloaded. There may be several reasons in this situation. This, in particular, is about the state of the fuel filter and carburetor.
• ICE of braids for grass is not started or immediately after launch stops working, which can be due to clogging of an air filter that prevents the normal supply of air necessary to enrich the mixture.

In addition to all of the above, owners of trimmers have to deal with more serious troubles. One of these is the wear of the piston group. In such cases, to entrust professionals, which will significantly reduce expenses and extend the life of the tool.

Floods the candle on the gas troops what to do

The owner of a summer cottage will not do without a lawn mower or a trimmer for grass. However, during its operation, of course, situations appear when this unit ceases to start for some reason. And the circumstances of this you will like a lot more. Let’s find out why the gasoline trimmer for grass does not start.

To find why the gasoline trimmer for the grass is poorly started or stalls, you need to check the work of all the main components of the unit in turn. In particular, it is fundamentally done after a long storage of the lawn mower. What you need, the main prerequisites for such a trimmer’s behavior for the grass are as follows:

• The culprit that the lawn mower is not started, you will like a bad butter-Benzine fuel mixture. You need to cook it strictly according to the annotation. The savings here are completely not appropriate, as it leads to the wear of the entire piston group of a trimmer for grass. It makes no sense to prepare a lot of fuel consistency, because excess gasoline will lose their properties over the years.
• You need to know that gasoline trimmers for grass of stamps such as STIHL, Husgvarna and some others do not start if they have cheap gasoline with a small octane number. For such units, only high.quality high.octane fuel should be used.
• If the trimmer for the grass stalls right away when starting, then maybe he has a candle flood. In this case, you need to turn it out and dry it well in 30 minutes. Then drain the excess of fuel, which is located in the cell, clean the candle from the carbon fiber, put it in the area and try to start the lawn mower.
• If your new gasoline trimmer for grass does not start, you will like a no spark more with a prerequisite. And this happens since the nest where the candle is placed, dry and fuel does not light up. You should slightly moisturize with a few drops of gasoline threaded connection of a candle.
• A gasoline trimmer for grass can stall due to clogging of air or fuel filters. It is more reliable to replace such elements with new.
• There are also variations of the exhaust channel and sapun. Cleaning these elements of the trimmer for the grass, it is possible to start the unit without special troubles.
• Another prerequisite why the gasoline trimmer does not start for the grass, even when there is a spark, and possibly clogging the carburetor. To clean the channels and nozzles, you need to blow them with compressed air using a compressor.

Not starting on a cool trimmer for grass. We eliminate the cause

Use to clean the carburetor and special washing.

Immediately after buying a trimmer for grass for grass, we are faced with a lot of questions. how to use it, how to refuel it (if we are talking about a gasoline tool), well, it is clear which fishing line is better to choose for a trimmer. The answer to the last question is looking for the text of the article.

How to quickly remove the stump without uprooting?

Some gardeners at a certain moment are faced with the need to cut down trees that increase in this area. As a result of this, stumps remain, if the trees were of significant size, it is very problematic to uproot them. The text of the article is told about other methods of getting rid of stumps.

• How to sharpen the chain of the chain of the stihl chain
• Adjustment of the carburetor of the chainsaw STIHL 180
• Fishing line refueling in a trimmer for Ryobi grass
• Why is an electric trimmer quickly heated for grass
• What is common between a chainsaw and melted cheese
• How much can diluted gasoline for a chainsaw can be stored
• How to adjust the carburetor on the Lifan motorblock
• When you need to cut trees in the garden

Currant processing in the fall from pests and diseases

That every summer resident grows currants, which is loved due to its own taste properties and the necessary parameters. She asks for appropriate care, which consists in the processing of plants from pests and diseases. The features of these autumn events are told in the text of the article.

How to choose a gasoline trimmer for grass for grass?

Beautiful well.groomed lawn. decoration at least some section. And the constant haircut helps to preserve its attractiveness. In this case, it will not do without a lawn mower or a trimmer for grass. On the text of the article we will talk about the intricacies of choosing a gasoline trimmer for grass.

In most cases, this occurs in beginners when, at the first launch, “cotton” is passed on a closed air damper and continue to pull the starter handle, respectively, gasoline in the combustion chamber is enough, and not a sufficient amount of air does not allow gasoline to be ignited.

floods the candle on a gas station

• Unscrew the candle with a candle key and check its condition. If the candle is wet and the spark is, of course, then it was flooded. Open the air damper, turn on the switch button, squeeze the gas “until it stops” and start. Excess gasoline should get out of the exhaust saw and the saw will start.
• Unscrew the candle with a candle key and check its condition. If the candle is wet and there is a spark, then it was flooded. Turn the chainsaw with the opening of the candle down and take the starter 10 times, while excesses of fuel will flow out of the motor cylinder.

Then wipe the dry dry (replace) a candle, or change to the latest and repeat the attempt to start the motor by accurately following the operation annotations. If the candle is completely dry, then this means that fuel does not enter the engine. And because it is in the tank, then perhaps the inconsistency in the carburetor. You can type a small consistency in the syringe, injected into the cylinder, tighten the candle and try to start the engine. If the engine started up in this matter, however, it remains, the non.bond remains and you need to contact the service center.

Probably garden tools are useful and effective, but there are times when the technique is abandoned to work. Among them, both a trimmer for grass, which have an option to dig a small clearing and large lawns, hit.

There are various prerequisites why the gasoline trimmer for the grass does not start:

The most common breakdown occasion lies in the wrong choice of fuel. Often very economical users of the device pour something incomprehensible into the tank, but not fuel with an ordinary octane number. The bad fuel, which was kept in the plastic canister, has a terrifying effect. The device that has lost performance therefore sets off to the full bulkhead of the mechanism.

Benzotrimmer does not start pouring a candle what to do

The owner of the suburban site cannot do without a brush or trimmer for grass. But in the process of its work, situations may arise when this device for some reason ceases to start. And there may be many reasons. Let’s find out why the gas trimmer for the grass does not start.

Why does a trimmer not start. the reasons

To determine why the gas trimmer for the grass does not start well or constantly delayed, it is necessary to constantly check the work of all the main components of the block. This is especially important to do after a long.term storage of a bushrer. Therefore, the main reasons for this behavior of the trimmer for grass are the following:

• The culprit that the motorcycle does not start, there may be a poor-quality fuel-benzine mixture. This should be prepared strictly in accordance with the instructions. Savings here are not at all suitable, as this can lead to the failure of the entire piston group of a trimmer for grass. Do not cook too much fuel mixture, since excess gasoline will lose its quality over time.
• You should know that gas trimmers for grass of stamps such as STIHL, Husgvarna and some others will not start if they are filled with cheap low.octane gasoline. Therefore, for such units, only high.quality high.octane fuel should be used.
• If the trimmer for the grass stops immediately after starting, there may be a candle of ignition in it. In this case, it must be unscrewed and thoroughly dried for half an hour. Then drain excess fuel from the chamber, clean the candle from soot, put it in place and try to start the brush.
• If your new gas trimmer for grass does not start, there may be a no spark. And this is because the nest where the candle is located is dry, and the fuel does not light up. Slightly moisten the threaded connection of the spark plug in a few drops of gasoline.
• A gas trimmer for grass can be stopped by clogged air or fuel filters. It is best to replace such things with new.
• Exhaust pipe and respiratory tract can also clog. After cleaning these elements of the trimmer for grass, you can easily start the device.
• Another reason why the gas trimmer for grass does not start even if there is a spark, there may be a clogged carburetor. To clean the channels and jets, it is necessary to blow them with compressed air using a compressor.

Wet candle with a chainsaw: why and what to do

Can be used to clean the carburetor and special flushing.

Immediately after buying a trimmer for grass for grass, we have many questions. how to use it correctly, how to refuel it (if it is a gasoline tool) and, of course, which fishing line is better to choose for a trimmer. Look for an answer to the last question in the article.

Benzotrimmer does not start pouring a candle what to do

How to quickly remove a stump without uprooting?

• How long does it take to charge the battery of an electric screwdriver
• The first launch of a trimmer for Patriot grass
• Adjusting the gasopyle carburetor
• A chainsaw or an electric saw that is better that is more reliable
• Diesel motoblocks in work
• How to work with a circular wood saw

Many gardeners sooner or later encounter the need to cut down trees growing on the site. After that, the stumps remain, and if the trees were large, they are very difficult to destroy. The article discusses alternative ways of getting rid of stumps.

Treatment of currant in the fall from pests and diseases

Almost every gardener grows currants that is loved for its taste and beneficial properties. Requires proper care, that is, the treatment of plants from pests and diseases. Features of these autumn events are described in the article.

Well.groomed lawn. Decoration of any territory. Regular haircut helps to preserve it attractive. In this case, you can not do without a lawn mower or a trimmer for grass. In this article we will talk about the intricacies of choosing a gas trimmer for grass.

What to do if the spark plug is flooded on the chainsaw?

This most often happens for beginners, when at the first launch they “clap” on a closed air damper and continue to pull the starter handle, respectively, there is a lot of gas in the combustion chamber, and no enough air prevents the gas production of gas.

• Use the wrench for the spark plug to unscrew the spark plug and check its condition. If the candle is wet and there is a spark, it is flooded. Open the air damper, turn on the switch, squeeze the gas “to the end” and start it. Excess gasoline should get out of the saw and the saw will start.
• Use the wrench for the spark plug to unscrew the spark plug and check its condition. If the candle is wet and there is a spark, it is flooded. Turn the chainsaw with a hole for the spark plug and turn the starter ten times, and the excess fuel will be excessed out of the engine cylinder. Then wipe the dry light of the ignition (bake) or replace it with a new one and try to start the engine exactly in accordance with the operating instructions. If the spark plug is completely dry, this means that the fuel does not enter the engine. And since he is in the tank, there may be a problem with the carburetor. You can dial a small piece into the syringe, insert it into the cylinder, turn on the spark plug and try to start the engine. But if the engine starts and immediately forgets, the problem remains, and you need to contact the service center.

You have no permission to publish Комментарии и мнения владельцев

The gas trimmer for the grass does not start. the reasons

Many garden tools are useful and effective, but there are times when the equipment refuses to work. Among them was a trimmer for grass, which could mow a miniature lawn and huge lawns.

The reasons why the gas trimmer for the grass will not start

There are various reasons why the gas trimmer for the grass does not start:

The most common reason for the refusal is the improper choice of fuel. Often too modest users of the device fill something doubtful into the tank, but not fuel with a normal octane number. The poor quality of fuel, which has long been stored in a plastic canister, has a terrible effect. A device that has lost its functionality for this reason is sent to the full section of the mechanism.

The lawn mower is not started: the reasons and methods of elimination

Diagnosis of the reasons why the lawn mower is not started. A quick return to the life of Chinese and domestic motorcycles with a two.stroke internal combustion engine.

It happens that a two.stroke motor does not even show flashes in the cylinder, but it happens. grabs, and then stalls. Do not be sad, this Chinese consumer goods can be repaired directly on the knee using a minimum of tools.

Before starting diagnostics, you need to make sure that the engine rotates with a slight resistance. If there is no compression in it, then the further is useless, and you need to change the piston (this is also nothing complicated, everything is as a designer).

Not starting on a cold trimmer for grass. we eliminate the cause

The trimmer for the grass does not start on the cold. The reason is an air leak that does not allow fuel to download. The gasoline trimmer does not start for grass still does not start, Cadet CC 98 b video trimmer for grass. In the camera.

The second reason why the garden tool does not work is the fuel ended. On Elinech T750, a fuel tank is located near the motor, but on most trimmers it is there. We unscrew the cap from the tank and pour gasoline there (the most optimal version of the AI-92, it is inexpensive and does not clog the carburetor as AI-76). Do not forget to add special oil for engines to the tank, 50 grams on the gas tank is enough, without it the motor will begin to “sneeze” and quickly become unusable. After cover the tank with a cap, wipe the surface of a trimmer for grass with a dry rag and our hands. A trimmer for Hitachi grass is not started. Repair, tool, regardless of their small dimensions. We also make the above manipulations to include a garden tool.

The owner of the summer cottage can not do without a lawn mower or. But in the process of its operation, situations may arise when this unit for some reason stops starting up. And there can be many reasons for this. Let’s find out why the gasoline trimmer for grass does not start.

Why is a trimmer not starting for grass. the reasons

To determine why the gasoline trimmer for grass is poorly started or stalls constantly, it is necessary to sequentially check the operation of all the main units of the unit

It is especially important to do this after a long.term storage of a lawn mower. So, the main reasons for such a trimmer’s behavior for the grass are as follows:

• The culprit that the lawn mower is not started, there may be a poor-quality oil-Benzine fuel mixture. It must be prepared strictly according to the instructions. The savings here are not at all appropriate, since it can lead to the failure of the entire piston group of a trimmer for grass. Do not cook too much fuel mixture, as excess gasoline will lose their qualities over time.
• You should know that gasoline trimmers for grass of stamps such as STIHL, Husgvarna and some others do not start if they are filled with cheap gasoline with a small octane number. Therefore, for such units, it is necessary to use only high.quality high.octane fuel.
• If the trimmer for the grass stalls immediately during the start, then perhaps he has a candle flooded. In this case, it is necessary to twist it and dry it well for half an hour. Then drain the excess fuel that is in the chamber, clean the candle from the carbon fiber, put it in place and try to start the lawn mower.
• If your new gasoline trimmer for grass does not start, there may be a lack of a spark. And this happens because the nest, where the candle is located, is dry and fuel does not light up. Should be slightly moisturized with a few drops of gasoline threaded connection of the candle.
• A gasoline trimmer for grass can stall due to clogging of air or fuel filters. It is best to replace such elements with new.
• The graduation canal and sapun can also clog. Cleaning these elements of the trimmer for the grass, it will be possible to start the unit without any problems.
• Another reason why the gasoline trimmer does not start for grass, even when there is a spark, there may be a clogging of a carburetor. To clean the channels and nozzles, it is necessary to blow them with compressed air using a compressor. You can use to clean the carburetor and special washing.
• If the gaskets of the carburetor are worn out, you need to change them. And in case of violation of the tightness of this device, you will have to determine the faulty part of the carburetor and replace it.
• A trimmer for grass may not be launched due to wear of the piston group. However, it is better to change such parts of the lawn mower in the service center.

Why is a trimmer not starting for grass gasoline? Reasons and their elimination

In the near future, the gasoline trimmer for the grass got the status of the 1st of the main tools in the arsenal of summer residents. And this is logical, because a motorized braid for grass allows you to quickly put a personal plot in order. But from time to time it happens that a trimmer for grass does not start on a hot and even cool. In such situations, it is necessary without the help of others to establish the cause of the malfunction. Let’s find out what to do if a trimmer does not start for grass. The prerequisites, which more often lead to such troubles, will be considered further.

Chinese lawn mowers, tests, repair and operation

Guys, all the good time of the day, I hope I will help. In general, the Chinese braid for the grass was mowing, after 3 days I try not to start up, gave Benza to the candle opening, then it stalled. After that it will not start. I dismantled the carburetor peeled off the compressor, removed Glushak, unscrewed the needle still not starting up. The candle is normal, there is a spark, I change the gap still does not start. I changed the rings last year, like smeared with sealant, there should not be sucked in anywhere.In Karba, the needle spin there 0 Embar does not start in any way. I never gave gas for 100%. I tried with a filter filter. The shuttle opened the click of the epic 0. For some reason I pour the candle dry the candle, I will work for half a second to work stalling. Regarding the mixture, the question if it unscrews it richer and if you tighten the bolt poorer? Will this affect the engine start? The oil was not poured into the cylinders, I did not check the compression in this way. In short, xs what to do. I hope for your tips, thanks.

ZZZDEDZZZZ wrote: Guys, good time of the day, I hope I will help me a problem. In general, the Chinese braid for the grass was mowing, after 3 days I try not to start up, gave Benza to the candle opening, then it stalled. After that it will not start. I dismantled the carburetor peeled off the compressor, removed Glushak, unscrewed the needle still not starting up. The candle is normal, there is a spark, I change the gap still does not start. I changed the rings last year, like smeared with sealant, there should not be sucked in anywhere.In Karba, the needle spin there 0 Embar does not start in any way. I never gave gas for 100%. I tried with a filter filter. The shuttle opened the click of the epic 0. For some reason I pour the candle dry the candle, I will work for half a second to work stalling. Regarding the mixture, the question if it unscrews it richer and if you tighten the bolt poorer? Will this affect the engine start? The oil was not poured into the cylinders, I did not check the compression in this way. In short, xs what to do. I hope for your tips, thanks.

A neighbor with a scythe had the same problem. Dancing with tambourine did not lead to anything. A braid for grass started a couple of seconds after drying and wiping a candle and stalled. The neighbor crushed all the Chinese loudly and their relatives up to the 10th knee. I also jumped a little nearby, and then went home, turned the candle out of my braid for the grass and put it on it. Started with Paul Pink. For the sake of the experiment, he screwed his candle into his braid. The experiment was a success. my stall began. The next day, the neighbor bought a new candle and forgot about this malfunction.

Chinese candles, they are like a lottery-someone will be lucky and the candle will work for a long time, and someone will fly like a neighbor.

PLOOTO65 wrote: Chinese candles, they are like a lottery

Yeah, I confirm. Put the saw (the essence does not change, the saw-toe for the grass) after work, after 2 weeks the same jokes, exactly the same. Changed the candle and all type-top. H.S. By the way, on the spit, the Kitayuz candle, for 3 years has been working. Changed, for the sake of an experiment for a new-painted. Returned to the ass of the Chinese and mustache.

The trimmer for the grass does not give full speed on full gas, it works normally on medium gas, and something is bad at all, and you can hear the sound in sound. ALKO 4125 grass trimmer, I got it after winter.

Project1. Well so, adjust the carb. Or, if after the winter the problem, check the condition of the filters, exhaust. For the sake of experiment, replace the candle.

PLOOTO65 wrote: a neighbor with a scythe had the same problem. Dancing with tambourine did not lead to anything. A braid for grass started a couple of seconds after drying and wiping a candle and stalled. The neighbor crushed all the Chinese loudly and their relatives up to the 10th knee. I also jumped a little nearby, and then went home, turned the candle out of my braid for the grass and put it on it. Started with Paul Pink. For the sake of the experiment, he screwed his candle into his braid. The experiment was a success. my stall began. The next day, the neighbor bought a new candle and forgot about this malfunction.

Chinese candles, they are like a lottery-someone will be lucky and the candle will work for a long time, and someone will fly like a neighbor.

The chip is that the candle is just and not Chinese are such things, and the chip is that on it a spark is much better than that of the Chinese

ZZZDEDZZZZ wrote: her spark is much better than the Chinese

But not the fact that she will work or work fine. If there is a spark with a twisted candle, this does not mean that it will work. There is a concept, verification of candles in a nesting, for they are stsuki, have the ability to lose a spark with compression.

4470 wrote: but not the fact that she will work or work fine. If there is a spark with a twisted candle, this does not mean that it will work. There is a concept, verification of candles in a nesting, for they are stsuki, have the ability to lose a spark with compression.

So in the dviglo do not climb not to check the rings? Ity to buy a candle in a magaz?

Xs, I have been torn to pieces of the engine, at least I tried any methods.

4470 wrote: xs, I have been torn to pieces of the engine, at least I tried any methods.

I wrote above that I tried only to try to drain the benz from the week 3 and fill the new one and can put on the probe another gap between the flywheel and the reel carb already 100500 for different settings made

4470 wrote: Put the saw (the essence does not change, the saw-toe for the grass) after work, after 2 weeks the same jokes, exactly the same. Changed the candle and all type-top.

F.FROM.I wrote: Good time of the day! I do not know her with a Chinese oblique name on the box, it is written “Zubble” a problem arose. She does not start. There is a spark. Tried to fill gasoline into a cylinder. He spilled over the muffler and all. Before that, he ranged her last season. Always started. After winter I can’t get. What is the problem? Tell.

Horoh wrote: Right time of day. Demon’s lawn mower, the topic was smoar. I did not find an answer, although such problems rose, the problem of leakage of gas.tacu gasoline through the sealing gum through which the tubes go, gasoline flows and foams at high speeds, with the lid unsettled everything. The valve from the lid is generally taken out, as soon as you squeeze the lid a little stronger, the gasoline has been oozing. there is no air pads, it is not an option to plant an elastic band on Hermete, before it did not flow!

The elastic band is drying out from the time of replacement every 2 years

Asteron wrote: Good day, dear! I have such a problem, the lawn mower (Chinese naturally) broke the starters (3 pieces diluted), and I did everything as it was stamped (sucked, damper, no more than 13 cords did not pull out, etc.D.) I thought of the starter themselves are poor.quality (since there was one and the same problem, the spring jumped out), and logically climbed to the vastness of the immense to look for the cause, and in fact, in the first video on the Utuba, I saw it. And so comrades experts question!: Why on all the videos of all the braids for the grass are bonded by virtually one hand, and I have to crank the starter at least have to rest against the engine with your foot (where the starters are clear from), where is such a “frantic” compression?! And sometimes such a problem is manifested as Plooto65 described above: “The cord pulls out of the hands”. I will be grateful for the slightest help, maybe someone can help?!

Wet spark plug on a benzotrimer. The engine flooded.

Surely many people who use small motorized equipment know what a “flooded” candle on the engine is and what unpleasant situations arise because of this. Very often, using the technique just acquired, many do not check the condition of the spark plug electrodes after updating the fuel and lubricants, but recall this only when the first faults appear.

If on a wet candle it is still possible at least some appearance on the electrodes of the spark discharge, then on a “flooded” candle of spark discharge will be already impossible. We hear about “flooded” candles more often than about “flooded” engines. It is even difficult for many to imagine such an engine until they are faced with this personally.

Wet sparking candle or flooded candle is the main feature of either a non.working candle, the absence of high voltage voltage on the electrodes of the candle, or the re.enrichment of the fuel mixture supplied to the engine’s working chamber.

In addition, this can be attributed to cases with poor.quality fuel, a reduced high.voltage stress and a weak compression degree. As a rule, one thing entails some other manifestations and you can easily get confused in determining the main, main reason for the malfunction.

Spark plug. Another lawn mower fell into our hands, or a benzotrimer, where they could not run the engine. No recommendations from observers and “friendly” neighbors did not even help. Replaced the spark plugs with new ones, but there was no result, and each next candle was twisted with wet.

Air filter of the engine of the lawn mower. The engine of the benzotrimmer was opened in stages. The air filter ring was moistened with the fuel completely. In the compartment where the filter element is installed, there was a large amount of fuel.

The throughput of a wet filter decreased, and even with a dry light of the ignition, the engine could not start due to the overlap with a wet filter element of supply of the required amount of air. Electrodes of the spark plug immediately, when the engine was first attempted, filled with fuel.

The muffler of the lawn mower. Through the fasteners of the muffler, on one of the fasteners, it was clearly visible an oil stain. Traces of oil can appear with a weak tightening of fasteners, when the pairs of waste oil along with exhaust gases seep through weak seals, but on this benzo.tank, the tightening of the nuts corresponded to the required effort.

And in the muffler itself we found about 50 60 ml of fuel. Not oil, but the very fuel that was in the fuel tank.

The engine of the lawn mower. When opening the engine, we expected to find some kind of surprise, and this was not a vain expectation. A certain amount of dense soot soot was present on the piston. The layered piston rings and a piston layer on the piston pointed out that when working with a benzocosa, the temperature regime of the engine was exceeded, which worked on a reinforced mixture.

Many manufacturers write directly at the container that the oil has good anti.dysfunctional, lubricating, anti.corrosion and temperature properties. But none of them will write: “Do not overheat the engine!”Or” strictly adhere to our recommendations!»What was poured instead of oil, or poured oil unmarried, it is difficult to say.

Crankcase. Most of all we were surprised by the engine Carter, which turned out to be filled with fuel full to edges. It happens when a certain amount of fuel is assembled in the engine crankcase, but that the crankcase is completely flooded with fuel. this is a rarity for us.

The engine worked ‘in the sweat of the face’, and the operator did not pay attention to fuel consumption, increased smoky, and lowering engine speeds. The engine of the lawn mower flooded at the very edges of the crankcase.

The carburetor of the lawn mower. There were no difficulties when disassembling a carburetor. Outside, the lawn mower carburetor was wet and dirty, which indicated fuel leakage, but we did not find the place of leakage at the external inspection itself.

Checking the fuel mixture

Suppose you don’t start a trimmer for grass. In this case, the first thing is to check whether the fuel is enough in the tank, as well as evaluate the quality of the fuel mixture. To refuel a motorized unit, it is necessary exclusively high.quality gasoline. It is recommended to use fuel, the brand of which is not lower than AI-95. Refueling a trimmer for grass with fuel of unknown origin, not bought at a gas station, is fraught with frequent failures in the work of the tool. This can cause a breakdown of the cylinder-piston system. Repair in this case often exceeds the cost of the device itself.

Why is a trimmer not starting for grass gasoline? Incorrect preparation of the fuel mixture may also lead to this, which consists of oil and gasoline. The proportions in which the specified components are connected are indicated by manufacturers in the guide for the operation of a trimmer for grass. Preparing the fuel mixture is extremely not recommended in large volumes, that is, for the future. Indeed, with prolonged savings, there is a loss of the determining properties of the substance. Therefore, if a trimmer for grass does not start, it is worth draining the old fuel and use freshly prepared fuel mixture.

The trimmer for the grass is very hot

Overheating of a trimmer for grass can occur for many reasons:

• Gasoline has not the same octane number indicated in the instructions for the unit;
• the proportions of gasoline and oil during the preparation of the fuel mixture are not observed;
• A mixture of fuel with butter has long been prepared (the mixture cannot be stored for more than 2 weeks);
• The trimmer for the grass works more than the time instructions;
• A low.power trimmer for grass on thick and hard grass is used, the device works with overload and quickly heats up;
• shifted towards the bar or the cassette lid clutched.

The latter happens if you install the mowing head inappropriate for this unit

, or when the axis shifts inside the bar. These changes make it difficult to rotate, the load on the engine increases, and it overheating.

Not starting on a cold trimmer for grass. we eliminate the cause

On the cold.The reason is an air leak that does not allow fuel to download. In the camera.

After several jerks, he will start and stall, which is a normal phenomenon. What to do when the fuel was definitely normal, there is a spark, but a trimmer for grass does not start a gasoline? Putting the damper to the working position, start the tool again and start working.

And again the carburetor.

Well, even if after such bullying your trimmer does not start for the grass, you can’t do without disassembling the carburetor. It may very well be that everything is to blame for the gathering of the needle in it. In any case, the disassembly and washing of this capricious mechanism certainly will not hurt.

In general, when a trimmer for the grass began to be capricious and stall, it is advisable to carry out complete prevention: to completely change the fuel mixture, try another oil, and also mandatory change the candle. The gasoline trimmer for the grass does not start? Reasons and decisions on. Practice shows that in many cases, it is precisely cheap low.quality candles that are to blame.

We examined the most typical reasons why a trimmer is not started for grass. If the matter is something more “exotic”, do not pass the campaign in the service center. You will probably find smaller and obvious breakdowns yourself.

floods the candle on a gas station

Probably garden tools are useful and effective, but there are times when the technique is abandoned to work. Among them, both a trimmer for grass, which have an option to dig a small clearing and large lawns, hit.

There are various prerequisites why the gasoline trimmer for the grass does not start:

• The most common breakdown occasion lies in the wrong choice of fuel. Often very economical users of the device pour something incomprehensible into the tank, but not fuel with an ordinary octane number. The bad fuel, which was kept in the plastic canister, has a terrifying effect. The device that has lost performance therefore sets off to the full bulkhead of the mechanism.

We are trying to start the engine

So, we figured out why it floods the candle on the scooter. The following repair methods and the methods of starting the engine are applicable to scooters with 2T and 4T engines.

• The method is suitable in the absence of a tool. If you poured a candle with attempts to start a scooter, then let it stand for 5 minutes. Then turn the gas handle until it stops and twist the engine with a starter for about 10 seconds. You can use the leg several times if the starter is faulty. Let go of the gas handle and try to start the engine again. you should turn out.
• In the presence of a candle key, you should twist the candle and warm it on the fire, having previously cleared from the carbon. When the candle is removed, you should “blow” the cylinder, rotating the engine with a starter or leg. Screw the candle and try to start. In case of failure, the spark plugs should be replaced.

Advice! Although the first method is faster, it is still recommended to use the second. Such a cleaning of the ignition system will help to avoid such problems for some time.

After reading this article, the described problem will no longer be terrible for you. Follow the state of the components and assemblies of your vehicle, carry out repairs on time, refuel with high.quality fuel, and your scooter will definitely be your reliable fellow traveler!

The first is a candle

First of all, you need to unscrew the candle. If it is wet, then the ignition system is faulty. Try wipe the candle, put it in the cap, attach it to the engine, pull the starter. There is a spark? If not, then you need to change the candle.

Replacing the candle did not help? Then you need to watch magneto, cable, ignition coil. The cable is nicknamed, the coil is checked for resistance (multimeter in the resistance measurement mode of 200 Ohms, one contact for the mass, the other to the reel exit should show from 0.4 to 2 ohms). Sometimes magnets are polluted on the flywheel, or the key is lung, and the ignition moment flies up. Chinese shit throws various surprises, but for the most part everything can be identified visually.

Be sure to pay attention to the coat of candles. If it is black, the candle is smoked, then the mixture is rich, or you mixed the fuel incorrectly

If the plaque is white, then the mixture is poor, and the engine could already die from the temperature. Ideally, the color should be brick, bright, without much raid.

Again, if the black candle is dead, you should not immediately sin on the carburetor and ignition. Plunge the new, see what plaque will be. Maybe just a candle was poor.quality.

We find the reasons why the lawn mower refuses to start

If the lawn mower stubbornly does not want to start, and for some reason you do not want or cannot contact the service workshop, then try to follow the simple algorithm for searching for a malfunction. As always, use an effective search method, moving from simple reasons to more complex.

Check the pressure level in the engine (compression). To do this, you will have to get a special device in advance. a compressometer for measuring the parameters of the lawn mower. Normal engine compression indicators should lie in the range from five to eight atmospheres (all the envy of the individual characteristics of your engine). The compression parameters of your unit should be indicated in the accompanying technical documentation. If the level of compression is much less than the indicated, then your piston system has failed, requires a deeper study, repair or replacement of your elements.

The engine of the lawn mower jammed. Although this type of malfunction is much less common in a cart type, but it cannot be completely excluded. Basically, the engine jamming is due to gross violations of the operation of the lawn mowers. But if this still happened, then the repair of the lawn mower in the service center will cost you not cheap. Therefore, always carefully read and observe the rules of operation, storage and maintenance of the device recommended by the manufacturer.

Falf of the starter of the lawn mower. Checking the functioning of the starter is quite simple: you just need to try to pull out the launch cord from the lawn mower. If it does not stretch, try unscrewing the top cover of the lawn mower with the trigger and try to pull the cord again. If this time the cord does not lend itself, we diagnose the breakdown of the starter.

If the cord after separating the cover from the engine began to stretch out, put the mitch on the side and try to turn the working knife with our hands several times. If the knife does not rotate, then the engine still jammed and you have to send it to the service center, conduct deep diagnosis and, depending on the result, repair or change.

Carburetor failed. This is the most common cause (more than half) of the breakdowns of the gas mowers of the cart type. The carburetor will have to be removed from the lawn mower, disassemble and carefully consider

Also pay attention to the serviceability of gaskets and the air damper, responsible for mixing air with fuel