Vibro -fuel does not start a spark eat. Advantages

Vibration fuel malfunctions and repair

Vibroophytles. equipment designed for tamping of soil and other bulk substances before laying paving slabs, during the repair and construction of roads, arranging pillows when laying pipelines. Repair of single.extent and reversing vibration stages usually trust professionals, since often the cause of breakdowns can be determined only using diagnostic equipment.

The most frequent breakdowns of vibro.fuel engines

The main element of this equipment is an electric, gasoline or diesel engine, and most of the breakdowns are connected with it. The most popular gasoline and diesel models are due to independence from the power source. Engine repair is recommended to trust professionals.

• Low oil level or its poor quality. It may cause why the vibration plate is not started, the engine is heated, the equipment will start and immediately stalls.
• Polluted air filter. Leads to power loss, unstable engine operation, and even to stop it.
• Fast of candles. Leads to difficulties when starting a gasoline unit or unstable operation.
• Incorrect carburetor adjustment. Leads to unstable functioning without load.

Damage of the vibration node

There are situations when the equipment is turned on, but the vibration node does not work. There are several reasons why the vibrating plate does not trim:

• The leakage of an omentum located on the shaft. The flow of oil leads to the rapid abrasion of the gears and the failure of the entire node. If you do not notice the flow of the oil seal in time, you will have to replace not only the gears, but also the details associated with them.
• Low engine speed. To launch the vibro.bore, it is necessary to increase the number of revolutions.
• Weakening of the drive belt. If the belt is slightly worn, then you can strengthen its stretch. A strongly worn belt is replaced.
• Engine malfunction. With the help of diagnostic tools, they determine the cause and eliminate it.

Why is the vibrating plate smoke?

During operation, uncharacteristic smoke can come out of the exhaust system, the color and type of which will help determine the type of malfunction.

• White smoke. If it appears when the equipment is launched at low temperatures, then there are no reasons for concern. it just warms up the cold engine. precisely, this is not smoke, but the steam that disappears when the motor is warmed up. White smoke that appears with a heated engine indicates a moisture entering an air filter or too high fuel humidity.
• Gray (blue, blue) smoke. Indicates the entry of oil into the cylinder. The second reason is to get oil into an air filter with a strong tilt of the unit.
• Black smoke. When such a smoke appears, you should check if the air damper is open. If it is open, then the problem may be in the fuel system.

Other frequent breakdowns

Steel bases usually work several seasons without defects. If small cracks appear, then they are eliminated using a welding machine. In the same way, defects are removed on the handle and engine frame.

If the base has cracked and a large crack appeared, then the element is replaced with a new.

As a rule, the replacement of the base is accompanied by the replacement of vibro shutters, which are installed between the engine and the working surface.

Another question that may arise during the operation of the unit: “Why is the clutt of vibration plate warm?””. The reason for this may be the excess of engine speed, compared with the value specified in the instructions, or other violations of the operating rules.

The reasons why the direct.flowing plate does not move forward, and models with reverse do not make movements forward/backward, can be:

• Lack of fuel;
• absence, low level or poor oil quality;
• belt break;
• overheating that arose due to clogging of air holes, poor quality oil.

Users often ask the question of why the belt is torn. Unfortunately, for rubber belts, this is a common occurrence. The most functional are models in which a steel synchronizing circuit is installed instead of the belt.

The masters of the service center equipped with modern diagnostic and repair equipment will be able to accurately determine the place and causes of the malfunction of a direct.flowing or reverse vibro.plate and qualitatively eliminate the problem.

How to adjust the carburetor

The module adjustment is carried out by the manufacturer. During the operation of the device, after repairing or cleaning the module, it becomes necessary to adjust the carburetor.

Carburetor setup does not require replacement of spare parts. Debugging is done with the help of 3 screws that are available in the design:

• L. controls the supply of fuel at low speeds;
• H. controls the fuel consumption and temperature, and is also responsible for supplying gasoline at high speeds;
• T. is responsible for the idle engine.

Adjustment of the carburetor of the trimmer for grass is carried out after the engine warms up. For this, 10 minutes of operation of the device at idle will be enough. The rotation of the mowing head at idle allows you to start directly to debug the screw t. It is turned counterclockwise to the cessation of rotation. Then the screw h is scrolled to the right and left to find the position in which the idle speed will be maximum. The screw is turned off on ¼ full turnover counterclockwise from the found point, this will be the working position.

According to the same technique, the screw l. After repairing the carburetor, the module is necessarily tuned so that the device works correctly.

The design of the vibration plate

The sealing effect on the soil coating is provided by the action of vibration of the shock type. Structurally, the unit includes three main blocks, as can be seen in the photo of the gasoline vibration plate:

The eccentric is activated due to engine operation. Vibration occurs, as a result of which the energy and vibrational action are transmitted through the sole of the tool to the surface, which is subject to ram.

The main constructive component of the device is an eccentric. It functions in the same way as a regular flywheel. Its design includes a shaft, which has the center of gravity shifted.

The transfer of vibration to the substrate during construction work is carried out through the sole of the machine. For effective compaction, the plate should be quite heavy, be resistant to wear. It is recommended to choose units with a working area, which optimally corresponds to the list of work performed on the construction site.

A working platform made of cast iron or steel is made. If it is planned to lay paving stones or tiles on the sidewalks, then the sole should have a rug of rubber or polyurethane. Rounded edges provide smooth movement, and stiffeners help to enhance the structure.

Why stalls and does not work a vibro.fuel. vibration fuel malfunctions

Vibroopers are used when it is required to compact a fresh coating of crushed stone, concrete or sand.

The device of the vibration fuel is simple:

• at the base of the mechanism, a cast.iron or steel plate that compacts the surface;
• in the center of the plate. a vibrator that transfers fluctuations on the stove;
• gasoline, diesel or electric engine;
• coupling;
• frame on which the entire unit holds.

There are two types of vibration stages:

In each of the parts of the vibration fuel, breakdowns may occur. Some vibration fuses can be repaired independently, others require contacting the Vibroophytte Repair Service Center.

To minimize the occurrence of malfunctions, it is necessary:

• strictly observe safety precautions and instructions for the use of vibration placers;
• use high.quality vibration plate, fuel and oil recommended by the manufacturer;
• Vibrooproplit maintenance in time.

We will analyze the most common breakdowns and malfunctions of vibration fuels.

The vibro.fuel engine does not start

What to do if the vibration plate does not start?

The reasons and ways to eliminate the vibration plate malfunction, if the engine is not started:

• The ignition switch is set to the “OKL” position. transfer the switch to the right position;
• incorrect position of the air damper. set the damper;
• low oil level. add oil;

What to do if the vibration plate does not start

• not enough fuel. season gasoline;
• The fuel is enough, but it does not enter the vibro.plate engine cylinder. check the fuel filter, transfer the fuel valve to the working position;
• There is no air entering the combustion chamber. check the condition of the air filter;
• the ignition system does not work. check the candle and other elements of the system.

If it was not possible to cope with the malfunction on its own, and the vibro.fuel engine is not started, contact the Vibro.Plit Repair Service Center.

The vibro.plate engine works unstable at idle, stalls or does not develop full power

The reasons and ways to eliminate the malfunction, if the vibro.fuel engine stalls, works unstable, or does not develop power:

• Gasoline of poor quality or with an exceeding the expiration date. to replace gas with a new one;
• unstable sparking. conducting the maintenance of the ignition system;
• The air or fuel filter was clogged. to clean or replace the filters;
• The vibro carburetor is not adjusted. contact the service center for proper adjustment;
• Details of the details of the piston group of the vibration plate. repair or replace the details.

The vibration plate is not high quality and deeply trim the surface

The reasons and ways to eliminate the malfunction in the event that the vibration plate is not high.quality and deeply crushing the surface:

• reduced engine speeds. increase speed;
• reduced revolutions of the vibrator due to slipping of the clutch coupling pads-check the cleanliness and integrity of the pad, if necessary, replace;

What to do if the vibration plate works poorly

If the vibrating plate is not suitable for this type of coating that is compacted, the work will be carried out poorly, and the vibration plate is threatened with serious breakdowns.

The vibration plate stops during operation

If the vibration plate stopped and does not work, the following reasons and ways to eliminate malfunctions are possible:

• Fuel or oil ended. pour what ended;
• The drive belt flew or broke. fix or replace the belt;
• The vibration plate overheats. let the vibrationplit cool, check the quality of the oil, check the patency of the air intake holes.

The vibration plate does not develop full speed

If the vibrating plate does not develop speed, the following causes of the malfunction and methods of eliminating it are possible:

• The throttle is not fully or incorrectly installed. open the damper or install correctly;
• The processed surface is too wet. dry the surface before starting;

What to do if the vibration plate does not develop speed

The vibro.fuel engine starts, but there is no vibration

The following reasons for the lack of vibration are possible:

• The belt is weakened or worn out the belt. replace the belt;
• clutch damaged. replace the clutch;
• too much oil. reduce the amount of oil.

Vibrophytic stove jumps or compacts the surface uneven

The reasons for the fact that the vibro.fuel is jumping:

How to eliminate problems with the vibrator

The main cause of the vibrator breakdown is the leakage of the omentum located on the shaft, while the oil follows. If the vibration mechanism is operated without lubrication, then the gears are erased, which leads to the failure of the entire node. Often in such cases, the repair is not limited only to their replacement, because the conjugated parts are also destroyed. The vibro.boss is disassembled and undergoing overhaul.

The remaining possible reasons that the oscillatory node does not work, and the methods for their elimination are given in the table further.

In order to identify the problem with the vibrator in time, you should monitor the presence of oil leakage: if it occurs, then you need to immediately replace the oil seals.

Repair of an electric motor

Before checking the equipment equipped with an electric engine, the power supply voltage should first check:

• If the electric motor is single-phase, then it should be 220 V, / permissible instructions for deviations from this parameter;
• When a three.phase engine is installed on the unit, a voltage of 380 V is necessary (plus or minus, but within the specified limits).

Check the voltage in the outlet using a multimeter, having previously determined using the instructions on what value its equipment electric motor is designed. The device switch is installed in the desired range. The probes are inserted into the corresponding nests.

Multimeter and similar measuring devices are indispensable when checking electrical equipment. With their help, the presence of breaks in the circuit, as well as regulatory indicators of the resistance of the windings of the electric motor are installed.

The reasons for the problems with the electric motor are presented in the table below, which also contains recommendations for the repair of problems.

In very rare cases, the electric motor jam. Often the reason for this is associated with bearings. Therefore, they must be periodically lubricated, according to the operational instructions, and with strong wear. replace new ones with new ones.

Useful videos

Below we bring to your attention several videos about the reasons why the lawn mower is not started, and about the ways to eliminate them.

The reasons why the lawn mower is not started or poorly starts “hot”, and what to do:

Another plot about why the lawn mower stalls or does not start “on hot”:

The lawn mower is poorly started or not starting “to cold”:

The Chinese lawn mower died down or stopped starting up:

The analysis of the situation when there is a spark, and the gasoline trimmer for the grass does not start:

Device and operation of the fuel supply system of a benzotrimmer

To correctly determine the cause of the absence of gasoline in the engine cylinder, it is necessary to study the device and operation of the fuel supply system of such motors.

The gas tank is noticeably lower than the engine, so the fuel comes in two ways:

To start a motorcycle, which has not been operated for some time, you must first pump up gasoline so that it fills the pipeline and carburetor, thereby forming a closed system.

The primer is made in the form of a rubber button, which is pressed with a finger, and the unidirectional movement of gasoline provides a valve.

When the operator pumped up the fuel, then performed the rest of the preparatory measures, which we talked about here, and the engine earned, the second way to supply fuel is turned on. When the piston moves down during the intake of the inlet, in the combustion chamber of the lawn mower there appears discharge, which sucks atmospheric air through the air filter.

The basis of the carburetor is the Venturi tube operating on the same principle as the popular spray cleaner and ordinary glass jar in the USSR.

The passing flow of air captivates droplets of fuel, and the ratio of air and gasoline in the finished mixture depends on the diameter of the nozzle limiting the flow of combustible fluid.

The faster the engine shaft is spinning, the stronger the operator presses the gas trigger, the higher the speed of the air flow passing by the nozzle, which means that more fuel enters the engine per unit of time.

Reasons for the cessation of fuel intake

These are the reasons why the fuel does not enter the cylinder:

• The gasoline ended in the tank;
• When starting the engine, the fuel was not pumped with a primer;
• Primer faulty;
• Due to the improper inclination, the fuel system was ripening;
• The fuel system is leaky;
• The ventilation hole of the gas tank clogged;
• Carburetor scored with dirty fuel.

Gasoline ended

The first sign that gasoline in the tank is over is the unstable operation of the motor, which drops for several seconds, then briefly raises the moment, sometimes “sneezes”, then stalls and does not start anymore.

It is not difficult to determine the reason. it is enough to look at the fuel tank. it is transparent, so the level of fuel is always visible.

Most often, inexperienced trimmers are found with such a reason, who do not know how to determine the working time at one gas station. This does not bring any harm to the engine of the trimmer for grass, but after refueling the tank with fuel, it is necessary to pump fuel according to the system, but if it is added to gasoline before it ends, you can do without pumping.

When starting the engine, the fuel was not pumped up with a primer

This reason is also characteristic of inexperienced owners of motorcycle, which have not yet brought the performance of this action to the level of reflex.

In addition to anxiety about the possible breakdown of the apparatus, neglect of the pumping of fuel will not give any negative consequences, but excessive experiences can lead to a breakdown of technology.

For example, an inexperienced user who has tried to launch the engine and failed to do this, begins to unconsciously apply too much effort to the starter cable, forgetting to choose a free move, which can lead to a breakdown of the mechanism.

Primemer malfunction

Most often, the cause of such a malfunction is a dependent valve that does not block the fuel movement in the opposite direction when pressing the primer button.

To reliably determine the cause without disassembling the device, pull the hand starter cable 30-50 times with a mandatory selection of free move, but without breakthrough. If this leads at least to the “sneezing” of the engine, then the problem is really in the primer, so the trimmer requires repairs.

Due to improper inclination, the fuel system was ill of

The fuel system caused by incorrect inclination is as follows:

• a change in the position of the drive shaft changes the angle of inclination of the fuel tank;
• Gasoline, following the power of attraction, strives down and is aloof from the suction tube;
• The air through the absorption tube enters the fuel system and after the production of a fuel located in the tube and carburetor, the engine stops receiving gasoline;
• After absorption of even a small portion of air created by the discharge engine is no longer enough to effective fuel promotion through the system, so even returning to the normal angle of inclination everything leads to stopping the motor.

The fuel system is undergoing

This is the most dangerous reason, because in addition to a violation of the supply of gasoline to the engine, it can lead to ignition of the arising fuel, which is fraught with serious burns or fire.

Most often, the source of the problem becomes either a leaking seal, or a damaged or jumped hose.

Any of the defects leads to the fuel system, and the main manifestation is gasoline drops and a strong smell.

The ventilation tube of the gas tank clogged

Despite the tightness of the fuel system, the gas tank provides a hole for supplying air that compensates the spent fuel. On the vast majority of trimmers, a hose passes through the ventilation hole, this protects the fuel from dust and dirt.

The speed of air through the tube is small, so the dust or dirt does not suck into it, so the fuel is not polluted. If this tube is clogged, then the discharge that occurs in the tank compensates for the discharge created by the piston, so the fuel movement stops.

Carburetor scored with dirty fuel

Poor.quality gasoline with large ms and various dirt can score the channels of the carburetor and disrupt the operation of all fuel supply systems.

On different operating modes, the motor requires a fuel mixture with a certain proportion of air and gasoline, if the proportions change, the operation of the motor is disturbed.

A working carburetor instantly responds to a change in the operating mode of the power unit, including increasing the load, adjusting the amount of fuel, but clogging deprives it of this ability. The result can be a strong drop in power and revolutions, and a complete stop of the motor.

Vibration fuel malfunctions and repair

The vibration plate is a construction equipment that is used to compact various bulk materials, for example, loose soil, sand, gravel-thoroughbred mixture. It is used when laying paving slabs, road construction, soil compaction in an built.up site and to perform a number of other works. The equipment operated under relatively difficult conditions may fail at the most inopportune moment. This happens for a variety of reasons. At the same time, many breakdowns can be eliminated independently without resorting to the help of the specialists of the service center. To carry out repairs with your own hands, you need to understand the design of the working unit, as well as get acquainted with the most common breakdowns and their causes.

The device of the vibration plate

The design of vibration fuels of various types and sizes is almost the same. Various equipment models have the following main nodes:

• drive mechanism, which is source of equipment movement;
• eccentric (vibrator). a node creating vibrations;
• working (supporting) plate that compacts the surface of the material;
• frame for the motor;
• handle serving to control the direction of movement.

By type of drive, vibration stations are divided into such types:

The most widespread gasoline units in practice, which are located between electric and diesel models. They are equipped with four.stroke internal combustion engines (ICE) with one or two cylinders. Cooling in engines. air. There are no gearbox models.

The detailed device of gasoline vibration plate is schematically shown in the photo below.

The vibrator consists of a debalanced shaft, which is installed in supports with bearings. The motor frame is connected to the supporting stove through shock absorbers made of rubber and metal. Using the belt, movement from the engine to the vibrator is transmitted, and the water tank is necessary to moisten the sole of the plate.

The supporting platform is made of steel or cast iron. Various additives are brought into the metal to reduce wear and extend the service life. Smaller details, such as gears and fists, make plastic in cheap models, and in more expensive (high.quality). made of hardened steel. When they work with a paving stones or paving slabs, they additionally adapt a polyurethane rug or rubber mat to the working platform.

Also, vibration fuels are equipped with removable wheels that are needed to transport data from units. Aggregate handles are often equipped with vibration protection pads to improve the convenience of operation and reduce the negative effects of fluctuations on the health of service personnel.

Equipment for compaction of bulk materials weighing from 0.7 tons in most cases does not have handles: it is controlled by a remote way.

Electric models of the vibration fuel are tied to the mains: electricity flows through a supply cable with a fork at the end. The equipment is equipped with three.phase or single.phase electric motors. A button on the power button is placed on the unit handle.

The main malfunctions of the vibration fuel

All malfunctions with vibration slabs are associated with their main nodes:

Since the engine is the main knot of the equipment, the largest number of breakdowns is associated with it. Each type of drive has its own problems, so they should be disassembled separately.

Malfunctions associated with the frame, stove and handle are extremely rare. Typically, these structural elements serve without problems for several years.

When there are minor cracks on the sole, handle or frame for the motor, they are eliminated using a welding machine. If the base is very worn out, then it is completely replaced. over, they also often perform the installation of new shock absorbers.

How to eliminate problems with the vibrator

The main cause of the vibrator breakdown is the leakage of the omentum located on the shaft, while the oil follows. If the vibration mechanism is operated without lubrication, then the gears are erased, which leads to the failure of the entire node. Often in such cases, the repair is not limited only to their replacement, because the conjugated parts are also destroyed. The vibro.boss is disassembled and undergoing overhaul.

The remaining possible reasons that the oscillatory node does not work, and the methods for their elimination are given in the table further.

In order to identify the problem with the vibrator in time, you should monitor the presence of oil leakage: if it occurs, then you need to immediately replace the oil seals.

Repair of an electric motor

Before checking the equipment equipped with an electric engine, the power supply voltage should first check:

• If the electric motor is single-phase, then it should be 220 V, / permissible instructions for deviations from this parameter;
• When a three.phase engine is installed on the unit, a voltage of 380 V is necessary (plus or minus, but within the specified limits).

Check the voltage in the outlet using a multimeter, having previously determined using the instructions on what value its equipment electric motor is designed. The device switch is installed in the desired range. The probes are inserted into the corresponding nests.

Multimeter and similar measuring devices are indispensable when checking electrical equipment. With their help, the presence of breaks in the circuit, as well as regulatory indicators of the resistance of the windings of the electric motor are installed.

Repair of the Vibro.fuel Honda, Masalta, Wacker, Weber and other manufacturers

Engine malfunctions. Basically, engine malfunctions occur due to the incorrect operation of the equipment by workers somehow low qualification of personnel, or insufficient briefing on the rules of operation of the equipment entrusted to him.

The malfunction is not the correct start of the engine. The engine is not correct to “throw” the spark plugs, which leads to its replacement and fuel entering the oil crankcase.

The malfunction is not the correct stop of the engine. The incorrect engine stop leads to fuel entering the oil crankcase. When mixing fuel and oil in the crankcase, oil loses its functions laid down by the manufacturer, which leads to a strong wear of the CPH and KSHM, output of the engine.

Malfunction for the use of oil not intended for a given engine. As if on vibro-stalks there is an air-cooled engine, it is not advisable to use oil with water cooling engines. When using conventional oil in air cooling engines, leads to overheating of the engine and the hair of the piston rings, which leads to increased fuel consumption and oil.

Malfunction of the stove split. Often occurs due to non-careful transportation and loading and loading work, which leads to the replacement of this unit.

Malfunction lack of lubricating fluid in the vibrator or the use of oil not intended for this unit.

ETO (daily maintenance) is a visual inspection of the vibrating plate for the presence of oil subtexts, checking the oil level in the engine, the condition of the air filter, the condition of shock absorbers, clutch couplings and a drive belt. also checking and broaching all threaded joints.

Then after a long lease: 1. Replacing all lubricating liquids. 2. Replacing the spark plug. 3. Replacing the air filter. four. Replacing drive belts. 5. Clutch replacement (if necessary). 6. Replacement of shock absorbers (if necessary).

Operating recommendations: 1. Oil control. 2. Fuel control in the tank (AI-92). 3. Turn on the ignition. four. Open the fuel valve. 5. Close the fuel damper. 6. Engine start by manual or electric starter. 7. Open the air damper. eight. Move the throttle to the desired engine speed.

Work in mode. 40 minutes. Rest. 20 minutes.

Engine stop: 1. Move the throttle to minimum turnover. 2. Close the fuel valve. 3. Turn off the ignition.

Subtleties of the device and repair of the vibration plate

To create “useful” vibration in construction equipment, vibrovalla, eccentrics and other elements are used. In these details, the center of the mass does not lie on the rotation axis. This feature leads to increased transverse loads on the bearings and can cause wear of seats. For high.quality repair of vibrationomas, it is necessary to use bearings and bushings with increased wear resistance. Repair of shafts and corps parts should be carried out with strict compliance with tolerances and landings.

We are responsible for our work, honestly and efficiently carry out repair of drills. pedarators, pumps for pumping solutions, vibration stamps, vibrorsovka and other construction tools and equipment.

Contact, we are the best in this market segment!

The vibration plate does not work, does not go, does not trim, stalls, smokes

The vibration plate is a building mechanism for performing tamping work. To understand the breakdowns and malfunctions of the vibration plate, you need to know a little about its device. Vibroopers are used when it is required to compact a fresh coating of crushed stone, concrete or sand.

There are two types of vibration stages:

We are repairing vibro.fuels of the following manufacturers: Atlas Copco, Champion, DDE, DIAM, Elitech, Grost, Helmut, Makita, Masalta, Patriot, TSS, ENKOR, VEKTOR, CBU, CALIBER, KRETON, Ammann, Wacker, Bomag, Weber, Dynapac, Termag. Splitstone, Oskar, Enar, Euro Shatal, Batmatic, Mikasa, Dinamic, Masalta.

Vibration stations are operated in difficult conditions and experience heavy loads. This leads to a large wear of parts and mechanisms and the need to carry out repairs. Our service center produces high.quality repair of vibration fuels and other construction equipment in all our specialists constantly undergo training in order to improve their qualifications.

We will analyze the most common breakdowns and malfunctions of vibration fuels.

Далее приводим неисправности виброплит: ATLAS COPCO, Champion, DDE, DIAM, ELITECH, GROST, HELMUT, Makita, MASALTA, PATRIOT, ТСС, ЭНКОР, VEKTOR, Зубр, Калибр, КРАТОН, AMMANN, WACKER, BOMAG, WEBER, DYNAPAC, TREMIX, Splitstone, Oskar, Enar, Euro Shatal, Batmatic, Mikasa, Dinamic, Masalta.

Electric vibrating plate: DIY manufacturing process

This is a universal tool designed for rallying various surfaces. Do.it.yourself electric vibration fuel can be made at home by any master.

Its main advantage is compactness. It makes it possible to carry out work in places where it is impossible to apply a standard factory rink. For frequent operation of a vibration pile with your own hands. the most suitable option.

Before you start collecting such a device at home, you need to understand what the principle of its operation is based on how its mechanism works. Do.it.yourself vibration pins consists of several details:

• a plate that can be made of cast iron, a metal sheet or a cast.iron slab;
• vibromechanism;
• Electrical engine;
• frame.

In their appearance, devices are divided into several groups:

They differ in their characteristics, which are both negative and positive.

Electric vibrating plate. A positive characteristic of such an unit can be called a low noise level. During operation, tramb sand, there are no toxic substances, combustion products are not formed. However, this device consumes a large amount of electric energy, it can hardly be called portable due to large dimensions.

Diesel vibration plate. This device has become popular thanks to high power and a small consumption of diesel fuel. Typically, such devices are used on an industrial scale. The reason is high performance and large sizes. However, the cost of such an unit is considerable.

Gasoline vibration plate. The main positive quality of this device was its mobility, achieved due to high compactness. The device is able to work on gasoline of any brand, it creates a minimum noise level.

This allows you to use it for trafficing tracks next to residential buildings. It is forbidden to work with such a device in rooms where there is no ventilation. Vapors of gasoline are very toxic.

Another drawback can be called the consumption of a large amount of fuel.

The basic indicators of the vibration fuel

When developing such a device, it is necessary to take into account:

Characteristics of vibro fuel of the reverse move.

The effort of vibration means the power that issues the base of the apparatus. To work with dense coatings, vibration must reach maximum indicators. With weak strokes, the soil will not have the required density.

The dimensions of the working surface show the pressure created by the plate on the cultivated land. The smaller the area, the less this indicator. Usually the highest value of this indicator reaches 0.3.

In other words, to achieve high efficiency, the minimum size of the processed surface is necessary. The highest indicator of vibration fuels having a cast.iron base.

The steel base has a lower coefficient.

All about homemade vibration placers

Surely the one who faced the construction of a house or cottage, at the final stage, had to equip the adjacent territory (personal plot).

As a rule, the bulk of such work is associated with the ennolation of paths and previously torn under various communication sites. First of all, the quality of this kind of work is due to how even the surface of the soil is.

So, for example, in order to ensure maximum adhesion of paving slabs, when laying it, the soil should be well sealed and leveled.

After the installation of all elements, the base is aligned and tamped with a vibrating plate.

For such platform works that do not allow the use of special equipment on the site, a vibrating plate is best suited. It serves precisely for the tamping of the soil, regardless of its type, and allows us to provide its rather high density. Although the market has a fairly large selection of vibration fuels, but sometimes it is the price that stops many owners to purchase it.

At this very moment the question arises: is it possible to collect such a plate yourself? By and large, any person with minimal technical knowledge is able to master this task.

Do not rush to immediately look for drawings and recommendations for its manufacture-first of all, it is necessary to decide whether it is necessary whether it is still necessary or not. Of course, if you need to compact 100 square meters on the site.

m, then such a home-made slab will be an indispensable assistant, but if it is only 10 square meters.m paths to the house, then do not waste time on its manufacture.

Types of vibration fuels

After the base of the base, we proceed to the installation of shovers. First you need to install all the cutters and only then prepare the base for tamping and laying.

Currently, vibro.fuels are represented by three types: gasoline, diesel and electric. As clear, their main difference is the type of engine used to create vibration and, accordingly, their power. The most in demand in our time are gasoline vibration placers.

Thus, diesel vibrating plate, compared with gasoline, is characterized by increased power and a large work resource. But this is absolutely not required in the construction of a private house or cottage.

As for the electrical vibration stages, their use is limited primarily by the presence and location of the power source. They are used, as a rule, in closed rooms.

The only way out to remove this restriction is to use an electric vibrating plate with a portable gasoline generator. At the same time, this will require additional costs, which determines their non.competitiveness.

Vibration stations differ depending on the direction of movement when performing work. Vibrogram can be with a direct or reverse course.

The reverse vibro allows you to move in different directions, which significantly increases the effectiveness of the coating tamping, basically they have a speed of movement up to 30 m/min.

Unlike such plates, slabs with a direct stroke move in one direction and require, if necessary, a repeated passage of a trammelted area. Their action is similar to the usual rink.

Repair of vibration fuels

Repair workshop “Rulesiti” offers you high.quality repair of vibration fuels. Vibroophytes, like other equipment, sometimes subjected to malfunctions and needs repair services.

Our experts provide you with a wide range of services in the repair of the vibration fuel, as well as other benzo and electrical engineering.

We produce high.quality repair of all known brands of vibration fuels, such as: ADA, Diam, Evolution, Grost, Sturm, Tsunami, Wacker Neuson, Zitrek, Caliber, Red Lighthouse, Mis, Splitstone, TSS, Energomash and many others.

Repair of vibration fuels of all types

The vibration plate is usually designed to compact bulk soils. sand, stone trifles, gravel, gravel. The vibrating plate can also be used to compact the tile coating laid on bulk soil.

Due to the vibration, the voids between the particles of bulk soil are reduced, air and water are replaced from the voids. But, like any technique, the vibration plate is subjected to technical malfunctions and needs to be repaired.

Our workshop will easily repair your vibration pound with qualitatively and professionally.

Vibration pages are divided into gasoline, diesel and electric. The vibration stations also differ from each other and in the nature of the movement (reverse and non.renegade).

The heart of gasoline vibro.plate is a gasoline engine that is installed on the supporting plate.

Accordingly, the more powerful the engine and more eccentric, the greater the force is given by a gasoline vibro.plate on a sealing surface. Our workshop has a rich experience with repairing gasoline vibration fuels.

Diesel vibration pages have greater power and resource than gasoline, thanks to reliable diesel engines. Therefore, they are used on construction sites with increased technical requirements for equipment.

The scope of diesel vibration stages is quite wide, but first of all, they are used on construction sites, where there are stringent requirements for mobility, ease of maintenance and maneuverability. These can be places where the construction of roads, railway and tram tracks, sidewalks, tracks and sports grounds are being carried out.

But at the workplace, technical problem may occur. Our repair workshop is ready to carry out that your diesel vibrating plate.

Vibrogram or electrical vibration stations are often easier for compaction than their gasoline analogues. This technique is designed, mainly for the seal of soil and sand, has less weight and power, works to a depth of 300 mm.

The area of ​​use of electric vibration stages is limited to the length of the cable and the network voltage (42, 220 or 380V), respectively, they are optimal to use them inside buildings and premises where the laid electrical communications are present.

Electric equipment breaks most often and we can provide you with high.quality repair of your electronics.

The use of reversible vibration fuels allows you to solve many problems that are not subject to bulky special equipment.

The small size of this equipment successfully fits into small spaces, and a reverse course expands the scope from horizontal surfaces to trenches and ravines.

Using reversible vibration stages, it becomes possible to achieve the proper quality of work even in the presence of hard.to.reach areas.

None.reureed vibration stations are used mainly for dimple repairs: both for sealing asphalt (in the presence of a watering system), and to compaction of the base. Models of this category are characterized by simplicity of design and exceptional reliability.

IP Lozitsky. rental of construction equipment and tools in Minsk

About the company rental of construction equipment and power tools in Minsk in a large assortment. Our warehouse is located at: g.Minsk, per. Olshevsky, house 7 We provide the following services, both in Minsk and throughout the territory of the Republic of Belarus:

Individual entrepreneur Lozitsky Nikolai Nikolaevich, acts on the basis of a certificate of state registration with registration number 290904509. Read more

New Diamonds and Frankfurt Kindias for mosaic-grinding machines of the COS and Splitstone milling

Here you can rent a mosaic-grinding machine of the type 220 V (single-rope) or 380 V (two-rot), and also purchase any mosaically grinding machine that interests you. In addition, we supply consumables for …… more thermal gun Master BV 690 Fs

Power 220 kW, rent from 120.00 /day

Renting a diesel gun Master. The rental is included with a barrel of 200 liters, as well as two hoses: the first to supply fuel, the second for the return. One of the most powerful in its class gun is 220 kW, with a stream of 12,500 meters of cubic per hour. …… more vibrotrams Masalta mr75r.

We offer services for the rental of gasoline vibrors in Minsk. or as it is also called-vibroonoga (slap-foot). Due to its constructive features and contrary to good compactness and small weight, it allows you to achieve the depth of seal more details Drill shock Makita HP 1631 KX

Drill with speed adjustment, additional handle and reverse. Characteristics: cartridge: fast.sounding; Opening hours: drilling, drilling with a blow; Power: 710 W; Nutrition: Network; Rotation speed: 3,200 revolutions per minute; Frequency …… more