Washing the air filter of a trimmer for grass Patriot. Carburetor petals and return fuel

Cleaning the air filter for a trimmer for the grass Husqvarna 128r

Useful material from which you will learn how to get a capricious gasoline trimmer for grass that does not want to work!

The summer time has come, and in the personal plots habitually hidden the lawn mower. Great tool, powerful and mobile. Using a gasoline trimmer for grass and grass, you can mow, and get rid of a dried.up weed. However, there are cases that the lawn mower does not start, works with interruptions or without developing full power. Of course, no one is at work! And as they say, you twitch the laborer’s handle more than the mowing.

Difficulties with the launch do not only have the types of motorcycle, but also in new. How to be in this situation? There is only one way out. to listen to the advice of experts and take advantage of their practical experience!

If you put a cable instead of a fishing line, without the possibility of its release, reliably fixing the two ends of the cable and cutting them with welding (a drop of melted metal holds the cable from blooming). Grass such a tool “falls” at a time. The shoot is cut off about a finger with a thickness. Stones are not as afraid as disk. There is true, the problem: when wear, pieces of cable threads break off, and these twisted wires remain in the place of mowing. If you step on them, you can get hurt.

But pieces of the cable remaining on the field are half a bastard. The fishing line for the trimmer, breaking off, weakens the dynamic blows to the transmission and the engine, the cable does not give such an opportunity. Result of quick wear of motorcycles.

Also, the ignition coil can be broken in electrical equipment. In this case, the lawn mower will not start or start and works with interruptions, and then stalls, or “hot” does not start at all.

You can check the serviceability of the coil in the same way as when checking the spark: we unscrew the candle, lean it against the trimmer body for the grass. If there is no spark with a jerk of the starter, or it appears through time. you need to change the coil.

Review of models

Gasoline braids for grass are widely used for professional laws care, as well as in agriculture. These samples of modern technology have proven their effectiveness when leaning weeds and hay harvesting

In such conditions, special attention is paid to the correct choice of the representative of the model range, taking into account the design characteristics and technical characteristics

At the moment, potential customers are offered the following models of the STIHL motorcycle:

To describe the main features of representatives of these categories, it is worth considering some samples of technology. So, the light lawn mower FS-38 is designed to perform simple landscape work, as a rule, in the conditions of personal plots. The weight of this tool is a little more than 4 kg. In this case, the operating volume of the engine and its power are 27.2 cm3 and 0.65 kW, respectively.

The main advantages of representatives of this category include the following operational indicators:

• insignificant weight;
• maximum ease of use;
• minimum fuel consumption;
• power plant power;
• reliability and long service life;
• minimum noise and vibration;
• modern design.

One of the popular models related to the segment of powerful trimmers is Stihl FS-13. The “heart” of this six.kilogram braid for the grass was an engine with a volume of 36.3 cubic centimeters and a power of 1.4 kW. The model is equipped with a tank with a volume of up to 0.5 liters. Powerful lawn mowers, as a rule, are classified as professional tools with the following advantages:

• increased power;
• maximum reliability and durability;
• the possibility of processing almost any surfaces, including thick shrubs;
• convenience and ease of operation;
• the presence of a “bicycle” holder handle.

How to rinse the air filter of a trimmer for grass

Some tricks of work with a benzotrimer.

Useful material from which you will learn how to get a capricious gasoline trimmer for grass that does not want to work!

The summer time has come, and in the personal plots habitually hidden the lawn mower. Great tool, powerful and mobile. Using a gasoline trimmer for grass and grass, you can mow, and get rid of a dried.up weed. However, there are cases that the lawn mower does not start, works with interruptions or without developing full power. Of course, no one is at work! And as they say, you twitch the laborer’s handle more than the mowing.

Difficulties with the launch do not only have the types of motorcycle, but also in new. How to be in this situation? There is only one way out. to listen to the advice of experts and take advantage of their practical experience!

If you put a cable instead of a fishing line, without the possibility of its release, reliably fixing the two ends of the cable and cutting them with welding (a drop of melted metal holds the cable from blooming). Grass such a tool “falls” at a time. The shoot is cut off about a finger with a thickness. Stones are not as afraid as disk. There is true, the problem: when wear, pieces of cable threads break off, and these twisted wires remain in the place of mowing. If you step on them, you can get hurt.

But pieces of the cable remaining on the field are half a bastard. The fishing line for the trimmer, breaking off, weakens the dynamic blows to the transmission and the engine, the cable does not give such an opportunity. Result of quick wear of motorcycles.

Also, the ignition coil can be broken in electrical equipment. In this case, the lawn mower will not start or start and works with interruptions, and then stalls, or “hot” does not start at all.

You can check the serviceability of the coil in the same way as when checking the spark: we unscrew the candle, lean it against the trimmer body for the grass. If there is no spark with a jerk of the starter, or it appears through time. you need to change the coil.

Garden Trimmer

A light and convenient trimmer for grass for removing grass, and even without a odorous fuel or an annoying electric cord clinging to everything that can be for which. You can mow vegetation even in the most inaccessible places, for example, near the fence, border or around the trees.

Powerful electric motor

Cope with dry grass and large weeds

Telescopic pen

will reach the most uncomfortable places

Protective shield

protect the face and eyes from flying garbage

Garden Trimmer Effective and economical

Compare a trimmer for grass for Garden Trimmer grass with more expensive and uncomfortable benzotrimers

Garden Trimmer

• Price: 1590 rub
• Compact and light
• Does not require skills in circulation
• Small
• Safe
• Works from cheap batteries aa

Is it worth buying

Buying motorcycles is determined by what purposes it will be applied. If you need to cut the lawn and remove weeds in a small area near the yard or in the garden, Chinese lawn mowers will fully cope with this task. In a short period of time, they will not overheat and provide comfortable work.

If you look closely for a professional option for direct work for about 8 or more hours, the Chinese manufacturer will not work

Pay attention to professional equipment with higher indicators and production capacity. Motokos needs to be purchased responsibly, because the service life largely depends on the quality of the equipment

So that the unit serves you as long as possible, follow the rules for using the device

Motokos needs to be purchased responsibly, because the service life largely depends on the quality of the equipment. So that the unit serves you as long as possible, follow the rules for using the device.

How to clean a diesel fuel filter?

In order to clean the diesel filter, it is necessary to determine its location. On vehicles with a diesel engine, it is most often located in the highest place of the diesel system in order to delay air bubbles that interfere with the correct supply of fuel. In modern car brands, the device can be located under the bottom of the car or in the engine compartment.

To clean the diesel filter, you do not need to use a hole or lift.

You can clean the fuel filter of diesel, following the phased instruction:

• First of all, it is necessary to unscrew the bolts with which the filter cover is screwed.
• Remove the lid.
• Disconnect the plug.
• There is a valve on the upper part of the filter case. It must be slightly unscrewed in order to align the pressure inside the device.
• Under the drain fitting, it is necessary to put any container for collecting fuel, and only after that it is twisted.
• You need to wait until the diesel fuel from the hose is completely dragging into the container.
• Twist the mounting ring from the body.
• Extract the filter with the lid.
• The inner space must be wiped with a dry rag that does not leave a pile behind.
• The cork (round ring ring) and the filter must be washed in acetone or in a non.combustible solvent, and then carefully blow them out of the air pump with air.
• Water is also removed from the cartridge using a pump.
• A sealing ring is put on the filter, after which the device is again put in place.
• Fuel is poured through the upper hole (until the level of diesel fuel reaches the top).
• The cork is twisted.
• All elements are collected again, the plug is connected.
• The vehicle starts up to 2000 revolutions. The motor in this state holds about one minute to avoid the formation of air traffic jams.
• After completion of the work, it is necessary to check the density of attaching the hoses to the fuel filter for the leakage of diesel fuel.

If after cleaning the device the problems with the engine did not disappear, this indicates the need to replace it or the availability of other problems with the vehicle. Independent cleaning requires certain professional skills, and in their absence it is better to contact the nearest car service.

It is impossible to ignore problems with the fuel filter, since driving a vehicle with a clogged mechanism can lead to the following consequences:

• The car engine will work malfunctioning or completely out of order.
• The consumption of diesel fuel will increase.
• Accelerators, lambla-zonds and spark plugs will begin to wear out quickly.
• The power system and fuel injection system will fail.

The numbers mean the following: fifty parts of gasoline are taken per part of the oil. Hence: 1000 ml (1 liter of gasoline) we divide by 50, we get 20 ml, that is, 1:50.

Thus, you can calculate the composition of the fuel mixture (gasoline/oil) in any proportions. To add oil to gasoline, not “by eye”, you can advise you to take a medical syringe with 20 ml, dial it in it and “inject” into the container for the preparation of the fuel mixture.

A small amount of oil mixed with gasoline leads to increased wear of the cylinder.piston group. An excess of oil in the mixture, although not so fatal, is also harmful. Cooking piston rings, rapid formation of soot in the combustion chamber, and a drop in engine power may occur. In addition, the mesh screen of the muffler is closed. Therefore, some users (after the end of the warranty period for a trimmer for grass) recommend it to be dismantled.

How to clean an air filter motorcycles ?

How to wash or clean an air filter on a benzotrimer, benzos, experimental: Izhmash Industrial Line GT 4350.

Gasoline used in motorcycles. AI 92. The brand of gasoline is accurately prescribed in the operating instructions. Do not try to “force” the engine, filling the 95th gasoline into it. This can lead to overheating, unstable work of a trimmer for grass and breakdown.

It is not recommended to leave fuel in a trimmer tank for grass with a long break in operation. It is better to finish the working day by completely developing the entire mixture. If this is not done, then because gasoline from the engine will evaporate during the night, and the thin oil filter will remain, carburetor jacks may clog. This will cause difficulties the next engine start.

It is also necessary to observe safety precautions when storing fuel. Many pour gasoline into a plastic bottle of water. Is it worth doing so?

Checking filters

Another common cause, due to which a trimmer for grass does not start, is the presence of a blockage in the filter area. To confirm the conjecture, just dismantle the indicated block and try to start the unit without it. If the engine of the trimmer for the grass has launched, most likely you will have to replace the air filter or at least perform a thorough purge of the old. In the presence of abundant contaminants on the surface of the filter element, it is necessary to use a new grid. Relying to such actions, you should not leave a suction pipe at all without a filter. After all, rush in this case can lead to the need to repair the entire piston group of the unit engine.

Before setting up the carburetor trimmer for the grass, it is necessary to do the following:

• Rinse the engine;
• replace or clean the spark plug;
• change to a new one or clean the air filter (it is recommended to lay it out in warm, soap water, squeeze it out and let it dry well).

It is also necessary to install the cord of the right diameter in the trimmer coil or install knives-this is done so that in the process of configuration the engine has at least some load. After installing a cutting tool and starting a gasoline engine, let it warm up for 10 minutes.

If at the idle speed of the motor you noticed that the cutting tool rotates, then it is necessary to reduce engine speeds. This is done using the lower idle regulator, often marked with the letter “T”. The figure below shows the placement of regulators on the trimmer Husqvarna.

But, for example, on the STIHL trimmer, this screw may have a label “LA”.

So, turn the idle control regulator to the left, until the trimmer head is completely stopped.

To configure the carburetor, 3 regulators are used (screw).

• The right regulator L tunes the level of enrichment of the combustible mixture at low speeds. It needs to be adjusted by the first. Get a maximum of turnover at idle. This is done using the regulator L, turning it to the left and right. After finding the point of maximum revolutions, return the regulator for half a turn to the left (against h. Arrows).
• The lower regulator t (LA) is used to configure idle. Turning it to the left, the engine speed will begin to decline, and when the regulator is turned to the right, the revolutions will increase.
• Left regulator h is responsible for enriching the combustible mixture at high speeds. The enrichment configuration completes the adjustment of the carburetor. Also, using this regulator, you can configure maximum speed, fuel consumption and engine power.

To exclude this trouble, adjustment will be required. With the working motor, give a full gas, then turn the “h” regulator to the right until a reduction in revolutions begins. After that, the “h” regulator must slowly scroll to the left until you hear the uneven operation of the engine. Then the regulator “h” should be rotated to the right until the moment of flat operation of the motor is heard.

After conducting the above actions, the setting of the carburetor can be considered completed. After proper adjustment, the engine must confidently gain momentum, a little four at a maximum of revolutions, and when working, an idle cutting tool should not turn. This manual is suitable for adjusting carburetors on the Huter, Patriot and others benzocos.

There are also carburetors without a screw that is responsible for enriching the combustible mixture at low speeds. That is, they have only 2 adjusting screws: a idle regulator and a quality fuel mixture regulator at high speeds. How to configure a carburetor of this type, you can find out from this video.

Analogs

On the world and market, two brands selling similar products. Sturm and Fubag can be distinguished. They are represented by the following models: the German benzotrimmer Fubag FPT 52 38712 and Sturm BT8952D, which have similar characteristics and fall into the same price range.

I purchased this model of a trimmer for grass last year to restore order on a garden plot. He used it only a few times, mostly my wife works with him. He copes with weight until she complained. Says that it is convenient to work. According to my feelings, I can say that it is very light and comfortable, if there was still a belt, then she would not be the price. For the overcrow of trees and shrub is great. In my opinion, it is not suitable for kosba in large volumes, since hands get tired. Otherwise, there were no problems with a motorcycle, everything works fine and does not fail.

I have been using this model of a trimmer for grass for 2 consecutive season. I mainly use hard.to.reach areas for the overcrow of hard.to.reach areas. Since you will not crawl to the trees and the fence close, I use a trimmer for grass. I like this tool. Starts the first time, even in cool weather. To do this, you only need to pump up a little fuel. And a fishing line for a trimmer is also very easy to change in it, there is a special position for this.

I was prompted by a constantly neatly cut lawn of a neighbor to buy a trimmer for the grass). I come to the cottage, I see his lawn and I want to put the same order at home. For this and acquired it. Now in my summer house, everything has become neatly and clean. In the management of the trimmer for the grass, I am quite happy with me. There is not a lot of fuel. Only noisy, but they, in my opinion, are all so loud. If we start mowing with a neighbor, such a symphony turns out that you can hear the whole district. I definitely recommend the acquisition.

Checking the fuel mixture

Suppose you don’t start a trimmer for grass. In this case, the first thing is to check whether the fuel is enough in the tank, as well as evaluate the quality of the fuel mixture. To refuel a motorized unit, it is necessary exclusively high.quality gasoline. It is recommended to use fuel, the brand of which is not lower than AI-95. Refueling a trimmer for grass with fuel of unknown origin, not bought at a gas station, is fraught with frequent failures in the work of the tool. This can cause a breakdown of the cylinder-piston system. Repair in this case often exceeds the cost of the device itself.

Why is a trimmer not starting for grass gasoline? Incorrect preparation of the fuel mixture may also lead to this, which consists of oil and gasoline. The proportions in which the specified components are connected are indicated by manufacturers in the guide for the operation of a trimmer for grass. Preparing the fuel mixture is extremely not recommended in large volumes, that is, for the future. If a chainsaw is not started: why and ways to eliminate. TC engine 4-stroke. A trimmer for grass is not started (gasoline)? Of the inexpensive, the best. Indeed, with prolonged savings, there is a loss of the determining properties of the substance. Therefore, if a trimmer is not started for grass

, It is worth draining the old fuel and use freshly prepared fuel mixture.

Diagnosis of malfunctions

The lawn mower cannot work for a long time. Gearbox and engine will overheat. Mowing no more than 15 = 20 minutes, taking a five.minute break. At a sultry afternoon, the operating time is halved. When mowing weeds, sedges of work, it is required to reduce the time.

With a unsuccessful launch, we begin to look for the reason for the refusal:

• Check the quality of the fuel,
• verify the operability of the candle and the purity of the candle canal,
• check the cleanliness of the air filter,
• make sure that the fuel filter is not clogged,
• Check the cleanliness of the saapun,
• Clean the exhaust channel.

complex reasons will be detected in the diagnosis of a malfunction, leading to the overhaul of the carburetor. Such reasons include clogging of the internal channels of the carburetor, wear on it gaskets and violation of the tightness of internal halls with a vacuum loss. DIY lawn mowing repair, if it does not start, will require patience.

Motokosa carburetor cleaning instructions: Fast method

Many people prefer to use a quick way to flush the carburetor of the lawn mower. This method is effective in the case when single malfunctions of the device are detected. Consider step by step how the process of disassembling and cleaning with your own hands occurs:

First you need to twist four fixing bolts from the primer.

After the carburetor is cleaned with compressed air, do not rush to put it on a motorcycle. Now you can check the serviceability of its functioning, or more precisely, how it pumps fuel. To do this, connect the hoses to the output fittings.

We lower the supply hose into the canister with gasoline, and download the primer.

If gasoline flows out of the return, then. work to clean the carburetor is completed successfully. Now you can install the part on the lawnical mower, and check the quality of the functioning of the tool. This is where the process of quickly cleaning the product is completed. In more detail, the entire cleaning procedure is presented in the video

How to clean a carburetor on a trimmer: complex cleaning with photo description and video

If your motorcycle is already for many years, and you feel that the tool has been working with interruptions, and attempts to configure the carburetor will not be crowned with success, then it is necessary to resort to the procedure for cleaning it. To do this, dismantle the part of the tool and, using a table with high.quality lighting, proceed to the matter. Next, a step.by.step process of disassembling, repairing and cleaning the carburetor from motorcycles is presented, which will be useful not only for beginner mowers, but also by experienced craftsmen:

We have a carburetor who needs to diagnose malfunctions and cleaning.

It is interesting! For washing, it is recommended to use gasoline or special washing liquid, the photo of which is shown below.

This is where the process of disassembly and washing is considered complete. Now let’s bring conclusions about the work done. Video on how to clean the carburetor of a trimmer for grass is presented below.

Chinese lawn mower. the carburetor valve hung and fuel overflows.

If gasoline began to flow out of the air filter, know that the reason is valve hanging. Traditional

When the piston moves from the lower dead point, at the initial moment the fuel breaks back into the carburetor. On high-speed engines most often used on motorcycles, a petal valve is used that does not allow the air-banding mixture to break out. There are valves:

Garage craftsmen advise bending the valve petals in case of failure. Practice shows that this is only a temporary measure and repair with the replacement of petals is not far off.

Diagnosis is performed by visual inspection. The presence of fragments or thermal damage, twist indicates the need to buy a new petal valve.

Despite the surprise of the appearance of fuel in the air filter and the inability to launch the engine, during operation you should listen to your bike, scooter, car. Small malfunctions in the operation of the engine should be alarming the owner, so that in the future not to see how the air filter pours gas to the ground.

The membrane leaked and spills fuel

The reasons that caused the appearance of holes in the membrane and, as a result, the appearance of fuel in the air filter can be:

The symptom of damage to the membrane is a deterioration in the intake manifold and air filter. There is a gradual deterioration in the technical characteristics of the car. Before the iron friend finally stalls, it can pass for more than one month.

To detect, whether the fuel flows through the membrane to disassemble the carburetor. Diagnosis is carried out by a visual inspection of it.

For repair, you will need to replace the membrane of the new. Before replacement, you should blow the carburetor to prevent garbage from getting into nozzles or under a shut.off needle.

Carburetor adjustment on the Patriot Pt 555 trimmer

Trimmer for grass gasoline Makita RBC 411U

Gasoline trimmer for the grass Makita RBC 411u. This is a light portable tool designed for mowing grass, small shrubs and single shoots of young trees in medium.sized areas. This is a semi.professional device used in both personal and public and forest purposes. Benzokosa Makita RBC 411U is easy to operate, highly effective and reliable.

Makita RBC 411U. The famous Japanese brand Makita, founded in 1915 by Mr. Masaburo Makita. In those days, the company was engaged in the repair and production of electric motors and generators, gained popularity and won the international market. In the 1990s, the company became a concern, expanding its offices and business around the world.

Currently, the Makita brand produces more than 1000 items of various equipment, including electric vehicles, manual and gasoline tools, garden equipment. The company’s engineers continue to develop and improve production, implementing new technologies, expanding the range. In this case, the quality always remains unchanged!

Advantages of Makita RBC 411U Motocos:

• Reliability.
• Mobility.
• Independence from the power source.
• Great power.
• Professional equipment.
• Designed to work in medium and large areas.
• The engine is updated.
• Environmentally friendly, the amount of exhaust gases is reduced.
• Built.in vibration damping system.
• Easy to operate and maintain.
• The possibility of using different cutting heads.
• Economy, low fuel consumption.
• Tender haircut along fences, borders.
• The function of the bush cutter is present.

Disadvantages Makita RBC 411u Motocos:

The weight of the bush cutter. 7.3 kg. Two.stroke gasoline engine is located at the top of the arrow. Its production capacity is 2 horsepower. The latest generation engine saves fuel and releases less air into the atmosphere. Starting power installation from the starter, a contactless ignition system. The gearbox is reinforced, angular, with a reptile.

For convenience, the gas trimmer for the grass of Makita is equipped with a system of extinguishing vibrations, a convenient shoulder belt evenly distributes the load, relieving the operator from fatigue with a prolonged span.

Rectangular bar, durable, hard shaft, bicycle handle. All designs are perfectly balanced. The lawn mower is designed for mowing grass, shrubs and young trees, the working organs have a knife blade or a hairpin 2 mm thick, you can install a disk.

The main problems and malfunctions of the carburetor.

The grid has only two problems with this element:

To determine the cause of the malfunction, unscrew the fuel filter lid to remove the mesh filter. If dirt just accumulated on it, the washing of gasoline or purging will help.

Be sure to install a new filter if there are any visible damage. There may also be damage to the fuel line (check this item during the repair).

The starter of the carburetor in most cases does not work due to blockages. For washing use acetone or the same gasoline.

Filling the parts of the carburetor clogged air is an acceptable and convenient repair practice.