What disk to cut an acrylic bath. Getting rid of calcareous plaque

It is necessary to shorten the acrylic bath? 2 real ways to do this quickly and efficiently

First you need to explain that shortening the bathtub radical, but not the only way to solve the problem. It is worth thinking about the following moments.

If you have saved documents for the goods, it can always be exchanged in the store for the appropriate. True, this may be due to some inconveniences: paying for movers and transportation to the purchase site, although it will be the most correct decision. Unfortunately, the necessary product is not always available, so you should look at the next method.

Make a gut in the wall under the bath. An excellent exit from the situation, the bath will acquire an additional support on board, and the design becomes much tougher. But this method is very dirty, and it is only possible if the tiles have not yet been laid, because cutting the stacked ceramics is a big risk. The supporting wall can also be an obstacle, it is strictly prohibited to make horizontal bar in it.

If the above methods have not come up to you, there is nothing left but to cut a bath. How to do this correctly and with less losses we will consider below.

It is necessary to shorten the acrylic bath? 2 real ways to do this quickly and efficiently

Home | Useful articles | It is necessary to shorten the acrylic bath? 2 real ways to do this quickly and efficiently

When buying an acrylic bath, it is always worth considering the area available for it in the room. After all, there are times when, bringing the just purchased bath to the house, unpacking it, it turns out that it is not subject to size. Before buying, you can measure the length of the room, its width, then in the store to measure the bath itself, but in the end it will still be suitable, since some small detail was not taken into account, for example, not yet laid tiles on the wall. Yes, such situations happen quite rarely, but if this happens, then what solution can be?

There are 2 ways to solve this problem, but in fact, the first way is to replace the bath with another in the store. This method is not considered the most successful, because most bathtubs are multiplying 10 centimeters in length, because of which, if you replace your “long” bath with a shorter, a very unpleasant gap may form. over, there is a chance that the store does not find the bath you need. One way or another, replacing the bath is quite easily an enforcement solution, especially compared to the second way.

As for the second method, this is the stroke of the wall. This option of shortening the bathtub has both their pros and cons, but we will start with the pluses. The first of which is that you don’t have to change the bath. Perhaps you chose a bath for a long time and tediously in appearance, by combination with a room, on decorative elements, replacement for another bath can turn into a whole problem. The second plus is that the correct stroke of the wall creates an additional stiffener frame for the bath, it will stand stronger, and accordingly it can last longer. We attribute to the disadvantages that it is not recommended to stroke a wall covered with tiles. this is not safe. Also, the problem may arise if the wall that needs to be stroobbed will be carrier, because making horizontal strobes in monolithic walls is strictly prohibited.

Many could have assumed that there is another way. trimming the bath. This is not advised to do this, since the sides along the edges of the bath are a kind of stiffness frame, cutting off which there is a risk to break the bath soon. Some people, cutting the bath, are trying to balance in stiffness with an additional homemade frame. This option can serve as a solution to the problem, but to build an additional stiffness frame is a rather laborious work and requires a specialist intervention.

On the site: author and editor of articles on the Pobetony website.ru Education and work experience: Higher technical education. Experience in various industries and construction sites. 12 years, of which 8 years. abroad. Other skills: has a 4th group of electrical safety tolerance. Calculations using large data arrays. Current employment: the last 4 years has been acting as an independent consultant in a number of construction companies.

Advantages and disadvantages of acrylic bathtub

Plumbing acrylic, which is used to produce this product, is a high.tech material. The inserts made from it possess:

• Light weight;
• High heat transfer;
• High mechanical strength;
• Sound absorption during water recruitment;
• Low cost.

Incorrect handling of such material leads to damage to the surface, it is very easy to scratch or melt, so care for the product requires compliance with the following rules:

• Do not use abrasive and aggressive cleaning agents;
• Use only a sponge soft on all sides for cleaning;
• Avoid hitting the surface of coloring products and chemicals, such as hair dye.

Why and what to drill, saw and cut an acrylic bath

Initially, the liner does not have holes for draining and water overflow. Naturally, they need to be done, or more precisely, drill.

This is done by a conventional drill or a battery screwdriver using a drill with a diameter of 5 mm and a special crown for wooden or stone holes. Its diameter should coincide with the circle of drain and overflow.

In order for the holes to coincide perfectly, put the liner into the main container and mark the centers of the plums. Then combine the drill with the center and drill part on the outside, and then from the inside. The turns should not be done too large.

After drilling, clean the edges with the smallest sandpaper.

Acrylic insert can be compared with a lid for a jar. She has sides that go around the edges of the capacity. If the bathtub is closely adjacent to the walls, then these sides must be cut or cut off.

Tools that you can use:

When cutting the edges of the corner grinder, we use cutting discs for any metal 1. 1 thick.6 mm.

Working with a jigsaw, install a special saw canvas with fine threads, then the cut will be cleaner.

Before you proceed to cut or cutting, make measurements very accurately and apply them to the sides of the liner with a felt.tip pen. The liner should perfectly enter the container, while you need to observe even contact with the wall.

Carry yourself with clockwork and confident movements to avoid an uneven, wavy edge.

Perhaps you decided to remove the old bath to put the tile behind it. In this case, the installation of the acrylic insert is best done without cutting. Then the deformation can be avoided, and under the liner water will not fall under any circumstances. This will increase its life.

If you want to get a new, beautiful, practical and comfortable bath, without spending a lot of unnecessary efforts and cash on it, make an acrylic bathtub using an insert. It will last you for a very long time.

Putting walls for wallpapers with your own hands Preparation of plastered walls for finishing is the most important stage in repair work. It is not very complicated, so it is not difficult to put the walls with your own hands for further staining or wallpaper.

How to choose a metal front door today is not easy to understand the huge assortment of the front doors from a variety of manufacturers. In this article we will tell you how to choose a metal front door to the apartment, taking into account all the nuances and requirements.

How to deal with the fungus in the bathroom and how it is dangerous with a rather unpleasant surprise for any of the tenants will meet in its own bathroom with a fungus or mold. The people who had to fight with them know that this can drag on for a long time and take a lot of effort.

Is it possible to glue the wallpaper on the wallpaper on the ceiling or wall in the apartment to make repairs, but I don’t want to breed dirt, dust, and then wash all this. In this regard, the question quite reasonably arises. if the wallpaper on the walls or ceiling hold well, whether it is possible to glue the wallpaper again on top of them?

Apparently not correctly removed the size of the room, the bath is longer and a little wider than we need.

Is it possible to somehow shorten (cut off) the acrylic bath, or is it worth not doing it?

Technically cutting an acrylic bath is not difficult.

But still I would not advise doing this.

The stiffness of the acrylic bathtub is not so big.

It is worse at times than a cast.iron bathtub and much worse than the steel.

Cutting the “side” of the bathtub along the length, or in width, you send the entire structure as a whole.

Even if it is a high.quality acrylic bath (cast acrylic, plus reinforcement).

If there is a check on your hands, hand over this bath to the store and buy a shorter, or narrower.

You can not take the bath, install the bath according to the time scheme, make markings and then in the wall are made (cut out) these are such strokes.

Strokes can be made on the length of the bathtub and short.

If the bath is not placed in length, it is longer and much, then we make a bar 2, on one side of the bath and on the other (parallel).

A bath (side) in the strobes, this is an additional fastener, that is, the whole bath will be installed tougher.

Of course, problems will arise when dismantling, but the baths have been operated for decades and even acrylic, if we observe a number of certain rules during its operation.

If you still decide to shorten, then in the beginning we make markings, apply a fishing line for a trimmer by a marker.

Acryl is easily cut, you can hacksaw for metal, you can an electric lobder and a file with a small tooth to it.

You can even a corner grinder, but a corner grinder is needed with a revolution regulator, a cutting circle for metal for an angular grinder, turn out minimum speeds.

How to cut an acrylic bath by 2 cm

First you need to explain that shortening the bathtub radical, but not the only way to solve the problem. It is worth thinking about the following moments.

Make a gut in the wall under the bath. An excellent exit from the situation, the bath will acquire an additional support on board, and the design becomes much tougher. But this method is very dirty, and it is only possible if the tiles have not yet been laid, because cutting the stacked ceramics is a big risk. The supporting wall can also be an obstacle, it is strictly prohibited to make horizontal bar in it.

If the above methods have not come up to you, there is nothing left but to cut a bath. How to do this correctly and with less losses we will consider below.

Is it possible to cut along the length?

The bath cannot categorically cut along the length. So you definitely strongly break the rigidity of the structure and the font will surely burst over time. It is better to get out of this situation in another way: to make a strobe after all.

Underwater rocks

What to do after the cutting work is carried out and how to protect yourself from possible negative consequences?

• Due to the decrease in the rigidity of the edge on the side of the section, during operation, some violation of the geometry of the bath is possible, what experts call “led”. Experienced masters in this case are advised to install a bath not on regular legs, but on a strong frame.
• You can return the necessary rigidity of the edge using the above set for repairing bumper from fiberglass and epoxy composition. It is necessary to glue them no longer a cut, but the inner surface of the bend of the edge of the bath, for 1-2 centimeters. This will help create an additional support of the edge.
• Can be attached to the wall, from the side of the cut, an aluminum profile or wooden bar. The board of the bath will be based on them. This will ensure the stiffness of the entire structure.

It is worth remembering that after shortening the bath, you will lose a guarantee. But this, unfortunately, nothing can be done about.

Is it possible to cut an acrylic bath and how to do it? Important features of high.quality sawing

Everyone who at least once in his life made repairs made mistakes. Imagine you bought an acrylic bathtub, they were about to install, and it did not fit in size, because the bathroom is shorter. Is it possible to saw it off in this case and how to do it right?

How to shorten it correctly?

If you still decide to remove a few centimeters from your bathtub, you should get acquainted with the instructions below:

The master is a master

We continue the theme of arranging the rank of node and in this article I will tell you how to install the screen under the bath.

As usual, in most cases, our bathrooms are small, and we want baths, as far as possible, large sizes. And therefore, many baths are installed between two walls. It is good if in the bathroom a place allows for installing a locker for all kinds of detergents and cleaning products, and all this good can be folded there. But often we are deprived of such luxury and all this good goes to storage precisely under the bath.

Is it worth cutting any material?

First you need to decide on what material your bath is made of and whether it can be sawed. There are two main varieties:

• Plastic made from ABS, they are produced using a very simplified technology. The acrylic layer is very thin, about 2 mm, in fact, it is formed fiberglass painted with acrylic paint.
• From cast acrylic, a layer thickness of 5 mm, the necessary antiseptic additives and reinforcement have been added.

Cast Acrylic products last much longer than models from ABS plastic. Some manufacturers give a guarantee of 15 years to their goods. During this time you will have to change three cheap baths, so

The first.type baths do not last long and quickly lose their presentation. Cut such baths inappropriately.

Cracks and scratches will certainly appear, and the design will lose rigidity. The second type of cups amenable to the cut, if you do everything right.

Necessary preparatory work before installing the liner

Acrylic liner is installed in the bathroom after all the stages of preparation are completed. Work begins with the dismantling of the side of the side side, which closes the seam between the wall and plumbing. As a rule, it is made of narrow tiles or plastic panels. They try to remove them as accurately as possible so as not to damage the wall decoration and at the same time open access to the board of the bath around the entire perimeter.

After that, the old enamel is cleaned with coarse.grained sandpaper by hand or performed with a corner grinder using an abrasive nozzle. Thus, it is possible to improve adhesion of the main surface and the latch. When the surface of the bath is evenly treated, it is thoroughly washed out of dust, dirt and chips that formed during the operation, degenerate and dismantled the siphon.

Advantages and disadvantages of acrylic bathtub

Plumbing acrylic, which is used to produce this product, is a high.tech material. The inserts made from it possess:

• Light weight;
• High heat transfer;
• High mechanical strength;
• Sound absorption during water recruitment;
• Low cost.

Another big plus: bacteria do not multiply on the acrylic surface. This is a very important quality for plumbing products.

Incorrect handling of such material leads to damage to the surface, it is very easy to scratch or melt, so care for the product requires compliance with the following rules:

• Do not use abrasive and aggressive cleaning agents;
• Use only a sponge soft on all sides for cleaning;
• Avoid hitting the surface of coloring products and chemicals, such as hair dye.

Important addition! In order to determine whether or not to put an acrylic insert in your bath, you must definitely consult a good specialist. This is due to the fact that these products are not produced for all types of containers.

Is it possible to cut along the length?

The bath cannot categorically cut along the length. So you definitely strongly break the rigidity of the structure and the font will surely burst over time. It is better to get out of this situation in another way: to make a strobe after all.

Is it worth cutting any material?

First you need to be caused by what material your bath is made of and whether it is possible to saw it. There are two main varieties:

• Made of ABS plastic, they are created using a very lightweight technology. The acrylic layer is very narrow, about 2 mm, in fact, it is formed fiberglass painted with acrylic paint.
• From cast acrylic, a layer thickness of 5 mm, the necessary disinfectant additives and reinforcement have been added.

Cracks and scratches will certainly appear, and the design will fail. The second type of cups are rendered if everything is done correctly.

As if you see, nothing terrible and unrealistic is that there is no acrylic bathtub to cut the edge of the acrylic bath without the help. Follow the simple rules, take your time and take measurements painstakingly. then the bath will serve for you for long and long years.

During the repair of the bathroom, many are faced with the question: what to do with an old bathroom? No one will hunt with the dismantling of a heavy metal capacity.

Modern technologies allow you to simply update it without excessive dirt and dust, using an acrylic insert. (rebuild the proposal by dividing it into two separate).

Is it possible to cut along the length?

The bath cannot categorically cut along the length. So you definitely very much violate the hardness of the structure and the font will certainly burst over time. It is better to get out of this situation in another way: to make a strobe all the same.

What to pay attention to when choosing a bath

In order not to be mistaken, it is enough to adhere to simple rules.

This is enough for prolonged operation. According to the technology and established standards in this area, the thickness of the acrylic is 6-8 mm, but some manufacturers seek to reduce the cost of products as much as possible to attract a wider target audience.

The reinforcing layer should be thick. This is especially important at the bottom and sides of the product. On the cut, the user must see 2 layers: acrylic and reinforcement. If only 1 is observed, it is most likely a composite product. In it, the thickness of the material is 1 mm (which is already bad), and the rest is plastic (usually of low quality).

Thorough measurements will be the key to choosing the most convenient solution, which will definitely fit into the room.

These rules are enough to order a product that, with proper installation, will last at least 20 years (standard warranty obligations for acrylic baths).

Why and what to drill, saw and cut an acrylic bath

Initially, the liner does not have holes for draining and water overflow. Naturally, they need to be done, or more precisely, drill.

This is done by a conventional drill or a battery screwdriver using a drill with a diameter of 5 mm and a special crown for wooden or stone holes. Its diameter should coincide with the circle of drain and overflow.

In order for the holes to coincide perfectly, put the liner into the main container and mark the centers of the plums. Then combine the drill with the center and drill part on the outside, and then from the inside. The turns should not be done too large.

For information: the thickness of a high.quality liner should be at least 6 mm.

After drilling, clean the edges with the smallest sandpaper.

Acrylic insert can be compared with a lid for a jar. She has sides that go around the edges of the capacity. If the bathtub is closely adjacent to the walls, then these sides must be cut or cut off.

Tools that you can use:

When cutting the edges of the corner grinder, we use cutting discs for any metal 1. 1 thick.6 mm.

Working with a jigsaw, install a special saw canvas with fine threads, then the cut will be cleaner.

Before you proceed to cut or cutting, make measurements very accurately and apply them to the sides of the liner with a felt.tip pen. The liner should perfectly enter the container, while you need to observe even contact with the wall.

Carry yourself with clockwork and confident movements to avoid an uneven, wavy edge.

Perhaps you decided to remove the old bath to put the tile behind it. In this case, the installation of the acrylic insert is best done without cutting. Then the deformation can be avoided, and under the liner water will not fall under any circumstances. This will increase its life.

If you want to get a new, beautiful, practical and comfortable bath, without spending a lot of unnecessary efforts and cash on it, make an acrylic bathtub using an insert. It will last you for a very long time.

Share with your friends:

Putting walls for wallpapers with your own hands Preparation of plastered walls for finishing is the most important stage in repair work. It is not very complicated, so it is not difficult to put the walls with your own hands for further staining or wallpaper.

How to choose a metal front door today is not easy to understand the huge assortment of the front doors from a variety of manufacturers. In this article we will tell you how to choose a metal front door to the apartment, taking into account all the nuances and requirements.

How to deal with the fungus in the bathroom and how it is dangerous with a rather unpleasant surprise for any of the tenants will meet in its own bathroom with a fungus or mold. The people who had to fight with them know that this can drag on for a long time and take a lot of effort.

Is it possible to glue the wallpaper on the wallpaper on the ceiling or wall in the apartment to make repairs, but I don’t want to breed dirt, dust, and then wash all this. In this regard, the question quite reasonably arises. if the wallpaper on the walls or ceiling hold well, whether it is possible to glue the wallpaper again on top of them?

Apparently not correctly removed the size of the room, the bath is longer and a little wider than we need.

Is it possible to somehow shorten (cut off) the acrylic bath, or is it worth not doing it?

Technically cutting an acrylic bath is not difficult.

But still I would not advise doing this.

The stiffness of the acrylic bathtub is not so big.

It is worse at times than a cast.iron bathtub and much worse than the steel.

Cutting the “side” of the bathtub along the length, or in width, you send the entire structure as a whole.

Even if it is a high.quality acrylic bath (cast acrylic, plus reinforcement).

If there is a check on your hands, hand over this bath to the store and buy a shorter, or narrower.

You can not take the bath, install the bath according to the time scheme, make markings and then in the wall are made (cut out) these are such strokes.

Strokes can be made on the length of the bathtub and short.

If the bath is not placed in length, it is longer and much, then we make a bar 2, on one side of the bath and on the other (parallel).

A bath (side) in the strobes, this is an additional fastener, that is, the whole bath will be installed tougher.

Of course, problems will arise when dismantling, but the baths have been operated for decades and even acrylic, if we observe a number of certain rules during its operation.

If you still decide to shorten, then in the beginning we make markings, apply a fishing line for a trimmer by a marker.

Acryl is easily cut, you can hacksaw for metal, you can an electric lobder and a file with a small tooth to it.

You can even a corner grinder, but a corner grinder is needed with a revolution regulator, a cutting circle for metal for an angular grinder, turn out minimum speeds.

Is it possible to cut an acrylic bath and how to do it? Important features of high.quality sawing

Everyone who at least once in his life made repairs made mistakes. Imagine you bought an acrylic bathtub, they were about to install, and it did not fit in size, because the bathroom is shorter. Is it possible to saw it off in this case and how to do it right?

Ways to get out of the situation

Firstly, it should be clarified that the reduction of the bath is radical, but this is not the only way to solve the problem. The following points should be considered.

Make a groove in a bath wall. An excellent exit from the situation, the bathroom from the outside will acquire an additional support, and the design becomes much tougher. But this method is very dirty, and it is possible only if the tile was not concluded, since the cutting of the laid ceramics is a big risk. The bearing wall can also become an obstacle; It is strictly forbidden to make horizontal grooves in it.

If the above methods did not suit you, there is no choice but to cut the bath. How to do this correctly and with less losses we will consider below.

Acrylic bath

You can cut 2 cm from the end of the bath (acrylic) so that it is suitable in size, what are the consequences for plastic? Exfoliates, etc.D.

Where are you all going to break the van acrylic? If there was cast iron, then no problems. Acrylic baths cut, and more than once. Nothing will happen to plastic. The only thing that needs to be restored to the stiffness of the stiffness before putting a cut bath is to apply to the wall, for example, an aluminum corner. All

I also think, especially since the end usually rounds down, forming rigidity

I would advise not to experiment. If there is no way to plunge into the wall, try to ask your question directly to the manufacturer.

I completely agree with you. All that can be cut off. Only then can the consequences be terrible.

Of course, you can, cut more than once. But, you need to think in advance, perhaps you should cut off one centimeter on both sides? It is necessary to glue the corner of the curb.

Better and accurately screw it into the wall! You did not put the tiles before installing the bath?

Perhaps, if then closed it with a curb or corners, the bath itself does not peel off and does not crack!

It is safer to grind, even if the stated tiles, a grinding machine with a diamond disk and forward. On the side where the stock is, the border tape will close, only you need to go to the tape with silicone!

If Basco is light, direct it more, to do it, what to open a bathhouse. Do not cut, draw fish

Acrylic baths cannot be fastened into the gutter (read the installation instructions), since when expanding the temperature it will have nowhere to go and it will crack.

Where are you all going to break the van acrylic? If there was cast iron, then no problems. Acrylic baths cut, and more than once. Nothing will happen to plastic. The only thing that needs to be restored to the stiffness of the stiffness before putting a cut bath is to apply to the wall, for example, an aluminum corner. All

Thanks for the competent advice, it’s a pity that I had not found your team before.

We and cast iron when he was cut. By the way, any bath can be cut without consequences, well, in general, everything is correct.

Cut nothing to exfoliate, verified.

Can be cut off, only stiffness is lost

I agree with Vitalik Arkhipov. Cut more than once))

It is better in the place on the wall where the bathtub rests, cut the canal with a small grinding machine, 5 mm larger than the side of the bath, and then, like a bath, set in a void or foam, or silicone sealant.

Dear masters! If there was an opportunity and a desire to install a bath without carving, then I would not have a question, not the first year after my husband.

You can cut off the bath, but what’s the problem? Better to hit the wall. We put cast iron 1.50 in the room 1.48

It is necessary to shorten the acrylic bath? 2 real ways to do this quickly and efficiently

When buying an acrylic bath, it is always worth considering the area available for it in the room. After all, there are times when, bringing the just purchased bath to the house, unpacking it, it turns out that it is not subject to size. Before buying, you can measure the length of the room, its width, then in the store to measure the bath itself, but in the end it will still be suitable, since some small detail was not taken into account, for example, not yet laid tiles on the wall. Yes, such situations happen quite rarely, but if this happens, then what solution can be?

There are 2 ways to solve this problem, but in fact, the first way is to replace the bath with another in the store. This method is not considered the most successful, because most bathtubs are multiplying 10 centimeters in length, because of which, if you replace your “long” bath with a shorter, a very unpleasant gap may form. over, there is a chance that the store does not find the bath you need. One way or another, replacing the bath is quite easily an enforcement solution, especially compared to the second way.

As for the second method, this is the stroke of the wall. This option of shortening the bathtub has both their pros and cons, but we will start with the pluses. The first of which is that you don’t have to change the bath. Perhaps you chose a bath for a long time and tediously in appearance, by combination with a room, on decorative elements, replacement for another bath can turn into a whole problem. The second plus is that the correct stroke of the wall creates an additional stiffener frame for the bath, it will stand stronger, and accordingly it can last longer. We attribute to the disadvantages that it is not recommended to stroke a wall covered with tiles. this is not safe. Also, the problem may arise if the wall that needs to be stroobbed will be carrier, because making horizontal strobes in monolithic walls is strictly prohibited.

Many could have assumed that there is another way. trimming the bath. This is not advised to do this, since the sides along the edges of the bath are a kind of stiffness frame, cutting off which there is a risk to break the bath soon. Some people, cutting the bath, are trying to balance in stiffness with an additional homemade frame. This option can serve as a solution to the problem, but to build an additional stiffness frame is a rather laborious work and requires a specialist intervention.

On the site: author and editor of articles on the Pobetony website.ru Education and work experience: Higher technical education. Experience in various industries and construction sites. 12 years, of which 8 years. abroad.Other skills: has a 4th group of electrical safety tolerance. Calculations using large data arrays.Current employment: the last 4 years has been acting as an independent consultant in a number of construction companies.