How to change the oil in an AL-KO lawnmower

Start changing the oil in the mower with the engine warmed up

Both methods work better if both the engine and the oil are warm. Make sure the mower is on a flat, level surface. It’s not a bad idea to put some newspaper or other material underneath to catch any oil that might be spilled.

Remove the spark plug wire from the spark plug and keep it separate from the spark plug to prevent unintentional starting.

Clean the area around the oil tank

Clean the oil refill area of any foreign particles.

Method with a siphon: if using an arnold siphon pump, siphon warm oil from the oil dipstick nozzle. Insert the pump/siphon tube into the oil dipstick nozzle until it reaches the bottom of the oil dipstick nozzle. Insert the pump/siphon tube into the oil dipstick nozzle until it reaches the bottom of the oil reservoir.

The way with tilt: place a suitable container for catching underneath the oil dipstick nozzle. Also make sure it is opposite the air cleaner so that the oil does not contaminate the air filter.

Selection Advice

The best way to lubricate 4-stroke mower engines is to use oil specifically formulated for them in accordance with the ambient air temperatures in which the equipment will be used. For example, the special oils of 10W40 and SAE30 grades are entirely suitable for four-stroke mowers, as they can be used at the ambient temperature ranging from 5 to 45 degrees Celsius.

these oils are recommended as good lubricants, taking into account the seasonality of lawnmowers. Hardly anyone would think of “starting” a lawn mower in sub-zero temperatures on the other side of the window.

In the absence of specialized oils, you can also use other grades of oils used for cars. they may be SAE 15W40 and SAE 20W50, which are also used at positive temperatures, but their threshold is 10 degrees below the specialized oils (up to 35 degrees). SF oil is also suitable for 90% of the four-stroke models available.

4T lawnmower oil containers should be marked with “4T”. Synthetic, semi-synthetic and mineral oils can be used. But in most cases semi-synthetic or mineral oil is used, because synthetic oil is very expensive.

So you don’t have to guess what kind of oil to put in your mower’s engine, it’s better to read the owner’s manual. It specifies the right type of oil, and the frequency of its replacement. It is recommended to use only the types of oil designated by the manufacturer until the expiration of the warranty repair period, in order to preserve the warranty issued. And then to choose something more affordable, but, obviously, not inferior in quality to branded oils. You should not save on oil quality.

Lubricants for lawn mowers with a 4-stroke engine

Lawn mowers have long since taken their place among the necessary appliances of owners of suburban and private homes, as well as employees of the park service. These machines are used rather intensively during the summer period. For the reliable and long-term operation of lawnmower engines, the quality of fuel and lubricants, namely oils, is of fundamental importance. This article is about oils for the 4-stroke engines of this type of garden machines.

Gasoline lawnmower engines are internal combustion engines (ICE), in which the driving force transmitted from the ICE to the working elements (cutting blades) appears due to the energy generated in the cylinder combustion chamber during the ignition of the fuel consistency. As a result of combustion, the gases expand, forcing the piston to move, which is connected with the mechanism of the upcoming transfer of energy to the final organ, in other words in this case. the blades of lawnmower.

In the engine, in such a manner, there is a great number of big and small details in the interface that need lubrication in order to prevent their fraying, destruction and wear, but at least to slow down these negative processes for the mechanism.

Due to the engine oil that gets into the engine and covers its rubbing elements with a narrow layer of oil film, the appearance of scratches, scrapes and burrs on the iron surface of the parts actually does not happen on new units.

But over time, this cannot be avoided, because the development of clearances in the joints still occurs. And the better the oil is, the longer the service life of gardening equipment will be. In addition to this, the following positive phenomena occur with the help of high quality lubrication:

• the best cooling of the motor and its parts, which prevents overheating and thermal shock;
• the engine work is guaranteed at enormous loads and with a huge time period of uninterrupted cutting of grass;
• preservation of internal engine parts from corrosion during seasonal machine idle periods.

Oil change for your Husqvarna mower

Lawnmower oil: how to change it correctly and which fluid is better to use

Lawn mower is a very useful thing for those who need to make repeated mowing of grass on lawns and other ground plots. But with the purchase of this tool it should not be forgotten that it, like any other mechanism, requires repeated maintenance. Oil change in lawnmower “Husqvarna” it is necessary to change the oil in the crankcase of wheel mower. One of these things is changing the oil. How to change the oil in a lawn mower, what fluid is better to fill? The answer you will learn from the article.

Why is it so important to keep the intervals?

First, let’s break down how fundamental it is to change the oil in your lawnmower at times. Firstly, the fluid cools the mechanism and allows the engine to work at maximum engine speed. In 2, lawnmower oil protects its parts during storage in winter time.

How often should the fluid be changed??

It should be noted that the frequency of oil changes depends directly on the technical condition of the motor. For example, if the engine on a lawnmower is new, the fluid needs to be changed immediately after the break-in period. In time it is approximately 5-6 hours of machine work. That in the future a variety of debris did not penetrate inside and accumulate in the engine, you need to make a couple of times more water substitution with an interval of 5-10 hours.

Changing the oil in your Husqvarna lawn mower

I have my first 500 subscribers!This video is tied to that number! It’s time to service the gasoline lawnmower

CHANGING THE OIL IN THE Husqvarna 4-stroke Lawnmower??

As it turns out, changing oil with a short neck is much more convenient.Poured fresh oil using a corrugator

If the engine is not new, lawnmower oil can be changed about once every 25-50 hours of operation of the tool. Changing the sprocket on a Husqvarna chainsaw recommendations: how to remove the sprocket from a chainsaw features clutch drum in chainsaws clutch drum replacement algorithm many. That’s about 2 to 3 months on average. You can also find the oil condition without measuring the number of hours worked. Change the oil in your Husqvarna lawnmower. Change the oil by tilting the mower. Just make sure it does not start to get a darker tint. When that happens, be sure to change the fluid, or else soon the engine could just jam.

Oil change

And now on to how to change the oil in your lawnmower. The whole process can be divided into several steps:

• The ancient liquid is connected first.
• Next, the lawnmower turns sideways (on the side where the drain hole is located) for a couple of minutes until the used fluid is one hundred percent drained. Next, the tool is placed back in a horizontal position. With all this, you need to prepare in advance a small container for the old oil.
• The Lawnmower is filled with new oil through the filler neck.

That’s it, this step is the end of the oil change. When pouring the new fluid into the throat, remember that it must be poured strictly to the marked mark in the crankcase.

Which lawnmower oil to choose??

It is necessary to make Accent on the fact that a certain type of water and its viscosity is directly dependent on the temperature criteria, in what this tool is used. So, if the weather is warm (temperature from plus 5 to plus 30 degrees Celsius), we recommend using the fluid series SAE-30. That is why an oil change is necessary. In daily use, changing the oil in the lawnmower. It has to be changed once a year. 2. Changing oil. In a lawn mower Husqvarna or. In the off-season season, experts advise pouring lawn mower oil with a viscosity of 10W-30. In winter you can use Synthetic 5W-30. Also worth considering is Synthetic 5W-30, which due to its properties ensures the reliable function of the lawnmower parts at relatively low temperatures.

How to Change Oil in an AL-KO Lawnmower

A lawn mower is a very necessary thing for those who need repetitive mowing of grass on lawns and other ground areas. But when buying this tool, do not forget that he, like any other mechanism, requires repeated maintenance. Lawn mower startup video. One of these moments is an oil change. How to change the oil in your lawnmower, what fluid is better to pour? You will learn the answer from the article.

Lawn mower. this is a very necessary thing for those who need repetitive mowing of grass on lawns and other ground areas. Electronic lawnmowers to do it yourself. But with the purchase of this tool, you should not forget that it, like any other mechanism, requires repeated maintenance. The design of the Makita 3710 lawn mower. One of these moments is to change the oil. How to change the oil in a lawnmower, what fluid is better to pour? You will find the answer in the article.

Why is it so important to observe the intervals?

To begin with, let’s review how important it is to change the oil in a lawn mower from time to time. Device and service of a Makita 3311 lawnmower. First, this fluid provides air cooling of the mechanism, thereby allowing the engine to operate at maximum RPM. 2, lawnmower oil protects lawnmower parts during winter storage.

How often should the fluid be changed?

It should be noted that the frequency of oil changes depends directly on the technical condition of the engine. Gasoline lawn mowers popularity rating. For example if the engine of a lawnmower is new then the fluid should be changed immediately after the break-in period. In terms of time it is about 5-6 hours of machine work. That in the future a variety of debris did not penetrate inside and did not accumulate in the engine, you need to make the substitution of water a couple of times with an interval of 5-10 hours.

How to change the oil in a DDE briggs stratton 675 lawnmower.

Changing the oil in the lawnmower, sharpening the blade and cutting the grass.

If the engine is not new, lawnmower oil can be changed about once every 25-50 hours of operation of the tool. Self-propelled petrol lawn mowers. It is on average 2-3 months of work. The smallest gasoline lawn mowers. You can also find the condition of the oil without measuring the number of hours worked. Just make sure it doesn’t start turning a darker color. When this happens, be sure to change the fluid, otherwise the engine may soon just jam.

Changing the oil

And now about how to change the oil in the lawnmower. Electric wide mowers. The whole process can be divided into several steps:

• The old fluid is combined first.
• Next, turn the mower sideways (on the side where the drain hole is placed) for a couple of minutes until the used fluid flows away completely. The machine is then placed back in its horizontal position. VIKING self propelled petrol lawn mowers rated. In all cases prepare a small container for the old oil beforehand.
• The lawnmower is filled with new oil via the filler neck.

At this point, the oil change can be considered complete. The best lawn mowers for grass. When you fill the throat of the new fluid, remember that it must be poured strictly to the marked mark in the crankcase.

What lawnmower oil to choose?

It is necessary to make Accent on the fact that a certain type of water and its viscosity depends directly on the temperature criteria, in which the tool is used. So, if the weather is warm (temperature of plus 5 to plus 30 degrees Celsius), it is recommended to use a fluid SAE-30. During the off-season, experts recommend that you fill your lawn mower oil with a viscosity of 10W-30. In winter you can use the fluid series 5W-30. You should also pay attention to Synthetic 5W-30, which due to its properties ensures reliable operation of lawnmower parts at relatively low temperatures.

Electric mower models

For cleaning flat areas, mtd electric lawn mowers are recommended. Which have undeniable advantages:

But these devices consume a lot of energy, so they are not fully mobile. Additional cables are required to remove grass at some distance from the socket, which slows down the operation.

The next step in lawnmower maintenance: cleaning

Quality lawnmower care is not possible without elementary cleaning of the deck and the engine from the grass.

Devegetation of the deck

The grass itself has an incredible corrosive effect on the machine, so it is necessary to periodically clean the DEKO. It is important to understand that a wet lawn should not be mowed under any circumstances, because then the negative impact will be doubled.

Dry vegetation will fall off the deck by itself, and the best way to clean it is to use an air compressor or blower. Some models are equipped with a special flushing connection, saving the user from additional hassle.

Getting rid of vegetation from the motor

Since mower motors are air-cooled, the entire system will only work properly if the ribs are not contaminated. Otherwise, expect overheating of the unit and its rapid failure.

The ribs can be cleaned by removing additional motor parts and using compressed air. Even a soft small brush will work perfectly, which in this case will demonstrate excellent efficiency.

owner’s manual

A step-by-step description of the steps and following the instructions will ensure that the tool works for a long time. This requires:

• Check for fuel and lubricants (gasoline and oil), for electric models for damaged cables.
• Only specialists should sharpen the cutter blade.
• If damage is detected, take it in for diagnosis.
• Turn the unit off when you stop mowing.
• Level the ground so that the blades do not become dull.
• Move the mower slowly and forward.
• Use a grass trimmer or lawn mower near walls and fences to prevent damage to the blade
• Reject the electric model if there is dew or rain. Use only in dry areas.

Important! Be sure to follow the safety rules so as not to harm your health and the health of your loved ones. Use electric mowers only in dry areas

Electric lawnmowers should only be used in dry rooms.

Lubricants and fuel

According to the manual, the mtd lawn mower should be started only after checking for fuel and lubricants. Lawnmowers, trimmers and brushcutters use special engine oil for two-stroke engines with air cooling system.

If the cooling system is rare, it won’t work. A container of such oil should be labeled “for garden equipment”. Usually the oil to gasoline ratio in the mixture is 2%: 20 grams of oil are added to 1 liter of gasoline. But it’s different, depending on the performance. Before you start, you need to figure out.

Start-up and operation

The first thing to do is carefully read the instructions. Then:

• Open the cap of the tank, refill the fuel to the mark and check the oil level, which is poured through the cap with a picture or labeled “oil”;
• Degrease the fuel pump;
• Check the spark plugs near the engine;
• Open the choke and move it to the middle or end position for normal gasoline access;
• Pull the cord sharply; sometimes it may take several tries.

Note! Since most new models come with a safety switch, it is important to keep it on when starting the tool. If it is inaccessible, make sure it is in a stable position

Remove grass residue from the blade and body during operation. Product should be stored in a dry, heated area. Also prevent overheating of the motor.

Typical deficiencies

Overheating can cause malfunctions.

Typical abnormalities in lawn mower operation can be:

• Stranger sounds, knocking: tighten bolts.
• Strong vibration: tighten bolts and see if blade works.
• A wheezing sound indicates the presence of a foreign body, which should be removed by pausing.
• Rough cuts can be repaired by sharpening or replacing blades.
• Stopping front wheel drive: adjust clutch cable tension.
• When the engine stops after starting, they check the oil level or start stuck items by hand or call a garden tool repair service.
• Mower off: check spark plugs and fuel.

There may also be other problems, including wear and tear or factory defects.

A lot depends on the proper care and maintenance of the garden tool. Then the daunting task of creating a beautiful lawn is solved very successfully with reliable equipment.

Replacing a Husqvarna 4-stroke oil mower ??

Turns out it’s much more convenient to change the oil with a long neck. I filled up with fresh corrugated oil

If the engine is not new, the lawnmower oil can be changed about once every 25-50 hours of operation of the tool. Changing the sprocket on your Husqvarna chain saw Recommendations: How to remove the sprocket from your chain saw The clutch drum has many algorithms for replacing the clutch drum. It averages out to 2 to 3 months of use. You can also find out the condition of the oil without measuring the number of hours worked. Changed the oil in the Husqvarna lawnmower, which replaces the oil by tipping the lawnmower. Just make sure it is not starting to darken. When this happens, be sure to change the fluid, or the engine may soon seize up.

Changing the oil

And now about how to change the oil in lawn mowers. The whole process can be divided into several steps:

• First combine the ancient fluid.
• Then the lawnmower is turned to the side (on the side where the drain hole is located) for a couple of minutes, until the waste water drains one hundred percent. The tool is then returned to its horizontal position. And you need to prepare a little container for the old oil beforehand.
• The new one is then poured through the mouth into the lawnmower.

At this stage, the oil change can be considered complete. When filling the neck with the last fluid, be sure to pour it out strictly to the mark in the crankcase.

Which lawnmower oil to choose?

It should be emphasized that the particular type of water and its viscosity depend directly on the temperature criteria in which the tool is used. So, if the weather is warm (temperature from plus 5 to plus 30 degrees Celsius), it is recommended to use SAE-30 fluid. That is why an oil change is required. For domestic use, change the oil in the lawn mower. Change it once a year. 2. Change oil. In a Husqvarna lawnmower or. In the off-season, experts advise filling lawn mower oil with a viscosity of 10W-30. In winter, 5W-30 fluid may be used

Also worth considering is Synthetic 5W-30, which has the properties to keep your lawnmower running reliably at relatively low temperatures

Oil change

Lubricant change should be done in a timely manner, according to the maintenance plan listed in the owner’s manual of each mower model. On average, lubrication efficiency is reduced after every 50 hours of operation. Clean the oil filter and change the oil when the mower is not in use.

• turn on the mower and warm up the engine for 15 minutes at idle speed;
• in the opening of the tank unscrew the plug;
• a container is placed to collect the waste;
• Tilt the unit in the direction of the drain;
• after the used material has been drained the plug is screwed in;
• the mower is placed on a flat surface and the opening is opened from above;
• fill up the oil to the required level, check the level with the dipstick;
• The hole is closed and the plug is screwed on.

the fill volume is up to 500-600 ml in most machines.

Features of lawn mowers

the engine oil in the lawnmower engine is distributed by the crankshaft: it is scooped up from the crankcase and sprayed on the parts. due to this design, the viscosity of the lubricant must be sufficient to retain the oil film on the parts, while at the same time it must not be too thick so as to impede the movement of the parts or form a hard crust.

Lawnmowers, on the other hand, operate mostly at positive ambient temperatures, so the strain on their engines is not as severe as on a car engine. Lawn mowers most often do not require a “cold start” in the cold, which greatly reduces the life of the car engine and requires low-temperature properties from the lubricant.

On the contrary, lawnmowers are usually air-cooled and therefore have higher engine temperatures than liquid-cooled car engines.

The first filling is intended for running in of the engine. after five hours of work it is replaced, then on the new lubricant can work the whole season. In the future replace it according to the regulations after a certain number of moto-hours, or drain it at the end of the cottage season and pour a new one for the next year.

The manufacturers

When choosing an oil, you need to pay a lot of attention to the oil manufacturer. It is better to choose the brand advised by the manufacturer of the lawnmower. You can find information about the oil you fill, how often you change it, and recommendations about choosing an operating-liquid fluid in the owner’s manual.

Also, many lawn mower manufacturers make their own oils that have to be used for replacement if you want to keep the warranty on the equipment. In addition, the manual provides the general characteristics that the oil must meet. This list should be used as a guide when selecting a replacement fluid. This allows you to choose the oil that will most accurately meet the requirements of the manufacturer.

Many self-respecting manufacturers of lubricants offer their customers a separate line of products, which are designed for the maintenance of garden equipment. If you can choose such a special oil, you should buy it.

• Among all companies that represent their products on the Russian market, the best is Shell Helix Ultra. These oils are popular in all countries. Shell has been working for 40 years to develop a unique technology for producing synthetic oil from natural gas. The resulting product is characterized by an improved composition, analogues of which do not exist at this time. The manufacturer adds the necessary additives to the base composition, which allows to obtain products with different characteristics. This oil should be purchased only at specialized outlets, as low-grade counterfeit products are not uncommon.
• Also the company Liqui Moly presents quality products. The manufacturer produces several product lines, which have different purposes. This range includes products for servicing garden equipment. Such oils are designed for long-term operation of trimmers and lawnmowers, their technical specifications are developed in accordance with the features of modern equipment and manufacturers’ recommendations.

Liqui Moly adds additive packages to lawnmower oils in order to reduce wear and tear and keep the engine clean. The main advantage of such liquids is the environmental friendliness, because they are made on a vegetable basis. The Liqui Moly lawnmower oils comply with all environmental regulations.

Rasenmaher makes a good mineral-based lubricant that was specially developed for lawn mowers. This product can be used for maintenance of 4-stroke engines with different cooling systems. Rasenmaher products can only be used at temperatures above zero. The manufacturer has carefully developed and selected additives for their product. The result of these actions is a wide list of functionalities:

Lawn mower blade sharpening

Operating a lawnmower with blunted knives severely injures the lawn, causing it to grow stale and continue to “hurt” for weeks on end. In addition, mowing grass with insufficiently sharp blades puts more stress on the mower’s engine and drive system parts.

Depending on the equipment of the lawnmower, its blade can be in the form of an ordinary blade plate or composite blade. In the latter case the upper part of the element serves for mulching the grass. The mower blade can be attached with one or two bolts. To remove the blade, unscrew the fasteners by turning them counterclockwise. After removing the blade you can inspect and sharpen it.

The need to sharpen the lawnmower blade is indicated by the presence of “sawing” and chipping on the cutting blade, which deteriorates the quality of cutting the grass. Blades with a rounded tip are also amenable to sharpening, as they severely traumatize the vegetation and get dirty quicker.

It is best to sharpen the cutter blades of the mower with an emery cloth of 400 to 600 grit. Before the blade is sharpened the bar should be soaked in soapy water. After that, the bar will need to be moistened in the same solution every 10 minutes as it is sharpened. To qualitatively and evenly sharpen the knife, the bar should be pulled from the center of the area towards its edge.

After sharpening blade must be corrected. To do this, the user will need moisture-resistant sandpaper with a grit up to 800 grit. The purpose of dressing is to remove burrs and other imperfections on the surface of the knife. To do this, you need to press the sandpaper to the outer plane of the existing descent and make several smooth movements from the grain. The paper should be progressively moved from the center of the area to the edges.

Repair and maintenance of petrol lawnmowers

The care of lawn mowers with gasoline engines includes a certain number of measures aimed at protecting the nodes of the unit from premature wear and tear.

Mandatory procedures include:

• use of gasoline and engine oil of the highest quality. Users should remember that a lawn mower motor needs constant lubrication. Without it, even the toughest engine will quickly overheat and fail;
• replacement of filters and hoses. gasoline mowers are equipped with filters and fuel hoses, which gradually become clogged and fail. The best way to clean them is to use gasoline and compressed air from a gas cylinder. Filters and hoses need to be changed if they are badly worn;
• timely inspection and replacement of parts of the cutting system. whatever mechanism is included in the construction of the mower, rotary or drum mower, its parts must work as smoothly and stably as possible. The user is required to constantly monitor the condition of the elements of the cutting system, sharpen and align the edges of the blades or change the blade if necessary;
• Drive system maintenance. a belt drive is the most common type of machine, but one that can get stretched and torn over time. In this case, the lawnmower repair with their own hands is reduced to the replacement of the belt and idlers;
• Eliminate vibrations and squeaks. Over time, many lawn mower users experience vibration that occurs 1-2 years after using the machine. The reason for this. the loosening of the bolts. Solve this problem with your own hands is simple enough. it is enough to tighten the bolts.

When using a lawn mower, it is important to regularly inspect the body of the machine. If it is made of metal, then sooner or later there will be s of corrosion on its surface. In this case, the operator must immediately remove the rust and cover the problem area with paint.

Testimonial: AL-KO 106118 Oil Change Kit. Universal syringe for 1,000 applications, not just pumping oil in garden equipment.

I’ve already written about BriggsStratton winter oil, but now here’s the perfect tool to change that oil in your gardening equipment.

Surely, many users of lawn mowers, cultivators and other generators have never known that you can change the oil in less than 5 (. ) minutes without getting dirty or spilling a drop.

Meet. set for the above magic.

Manufactured under the brand Al-ko, part number 106118

The whole kit consists of 3 items, of which a hardware guy like me only needs one piece. is a syringe. All the rest. is from the evil one. Or for those who have only a screwdriver and hammer.

But back to the kit. Here’s a live lineup:

I didn’t get lazy and counted how many funnels I have in my household. Not in the kitchen, but in the garage. On the 5th stopped counting, got bored. Bottles. Hmmm. Of course no one has a plastic lemonade/mineral water/beer/etc bottle.

But let’s stop mocking the pedantic Germans, because not everyone is as stocky as I am.

Instead of the instructions, right on the box in 3 pictures it says that a syringe should be pumped with the oil, not put in an enema. Pour oil into the included bottle, not on the ground, and pour fresh oil through the included funnel again, not by eye, trying to catch a stream of oil blown by the wind on all four sides and spraying everything in its path, including the uncooled muffler of your favorite equipment a second before the epic fiasco.

And in confirmation of the fact that after buying a set, you will get to Zen, on the box end there is a description of its purpose in 6 languages, one of which is our own.

I’d also like to point out the main attraction of the evening. This is not just a plastic syringe, but it has a measuring scale!!

You don’t need a scale to suck, and forgive me for using such a harsh expression, but you do need a scale to pour.

If you doubt the advisability of pouring oil SIM tool, just show a photo of the drain and fill hole in my generator.

See the bolt head at the base of the engine? Try draining a liter of oil without getting it dirty! The only option. is to lift it up on the bars. But he weighs 55 kilograms. Empty. And pour it into a hole like this under the yellow cap? The funnel won’t reach, and even if it did you can’t reach the funnel with the canister. You can hose down the funnel and do this oil masturbation for half an hour, messing all over the place. And you can drain and pour a liter (!!) of oil in less than 5 minutes and still be clean. Do the math: 3 double squeezes of the syringe for 10 seconds each and the oil is drained. The same amount more. and the oil is fresh, and you measure it exactly by the scale on the syringe barrel. 2 minutes of work with a syringe. Impressive?

And now about 1,000 uses in the home. Those, who service their own cars in terms of oil changes, are familiar with the problem of inconvenient pouring oil into gearboxes, axle differentials and transfer boxes. I had no idea how much easier this syringe makes this action. And you can also change the brake fluid by pumping the old one out of the tank. And antifreeze as well. Anyway, guys, a syringe like this. that’s a total hoot for a car enthusiast!!

Wrapping up my cart, I want to tell you that the price of 750r. for a device like this, that’s great. If you can find a cheaper one. and it’s a real buzz kill. But also 750 ree for no agony and oil change in a couple of minutes. This is the dream of many, I’m sure.