How to remove the clutch from a STIHL 180 chain saw

Learn how to remove the clutch on a chainsaw with examples from leading brands like STIHL, Husqvarna and Partner

Repairs to any machine must start with preparatory work, and the STIHL 180 is no exception. The STIHL 180 chain saw requires the removal of the side cover, the chain and the guide bar before it can be disassembled. Next, using a compressor and a brush, it is necessary to clean the chainsaw from dirt, sawdust, oil stains and other things.

When cleaning the saw, special attention should be paid to the place where the chain saw’s drive sprocket is located, i.e. к. this is the most contaminated area.

Where there is a lot of oil, you can wash it off with clean gasoline.

When to remove the clutch

Disassembly of the clutch in order to remove it is carried out in such cases:

• When the spring is broken (the chain turns, the engine runs intermittently);
• the spring is gone;
• a piece of the drum has broken off (in this case you will hear a noise, the chain of the chainsaw will also rotate);
• temporary wear and tear (it’s time to remove and replace the clutch because it has used up its life).

Modern chainsaws run on two-stroke engines, which are connected by a reducer to the saw chain. The chain moves along the bar and, according to the centrifugal principle, should stay stationary at idle speed, i.e. be safe for the person holding the chainsaw.

If the load on the tool exceeds the recommended load, the clutch will loosen or completely stop transmitting torque to the bar. This will cause the engine to stop. When these situations occur, the clutch wears out, so it needs to be replaced over time. Some chainsaw manufacturers’ manuals say that the clutch is an expendable part, which means that it has to be replaced from time to time.

Video. how to remove the clutch on a chainsaw:

When should the clutch be removed?

Disassembly of the clutch in order to remove it is carried out in such cases:

• when the spring has broken (the chain will rotate, the engine will run intermittently);
• the spring is off;
• a piece of the drum has broken off (in this case, a noise will be heard, the chain of the chainsaw will also rotate);
• Temporary wear and tear (it’s time to remove and replace the clutch due to wear and tear).

Today’s chain saws run on two-stroke engines, which are connected by a gearbox to the saw chain. The chain slides on the bar and according to the centrifugal principle must be able to remain stationary at idle speed, i.e. be safe for the person holding the chain saw.

If the load on the tool exceeds the recommended load, the clutch will loosen or completely stop transmitting torque to the bar. This will cause the engine to stop. When these situations occur, the clutch will wear out, so it will need to be replaced over time. Some manufacturers’ manuals for chain saws indicate that the clutch is a consumable item and must be replaced from time to time.

Video. how to remove the clutch on a chainsaw:

How to remove the clutch on a STIHL chain saw

How to remove the clutch on a STIHL chain saw

How to remove the sprocket from a Husqvarna chainsaw. STIHL ms 660 chain saw repair. replacement of the drive sprocket, partial disassembly of the STIHL!When you are doing a STIHL chain saw repair yourself, the correct procedure is to alternate between inspecting the STIHL MC 180 and disassembling it. The STIHL MS 180 is a reliable and undemanding machine but needs to be repaired from time to time just like any other piece of equipment.At the preliminary step, before making a disassembly of chain saw STIHL 180, you need to remove the side cover from the chain saw In the Other Auto-Themes on how to remove the clutch brake from the crankshaft chain saw STIHL this creator Lyudmila Brova best answer is I do so, I take a rope and tie on her knots with a distance of about a centimeter or two remove the circlip disconnect the air damper, remove the throttle pull the gas pedal with the springNew saw blades should be selected according to the characteristics indicated in the STIHL STIHL 180 chain saw instruction manual. Do-it-yourself construction and renovation. How to remove the clutch on a STIHL chainsaw ?And yet, chainsaw repairs can be time-consuming No chainsaw repair manual is going to change the normal logic of a chainsaw clutch.How to remove the chain saw clutch? The clutch drum is the drive sprocket. How to remove a chainsaw clutch. STIHL mc 180 chain saw repair.how to remove the magneto from a chainsaw. The China chainsaw clutch removal tool is a VERY useful gadget. STIHL MS180 overhaul. STIHL MS180 chain saw is not the cheapest to repair and has some factory defects, but at the same time lightweight, small-sized and revolving. Comfortable working. Remove the safety catch with a spark plug wrench and two 19 nuts. Where to use: All STIHL chain saws. 16. clutch clutch.It can be removed to replace the sprocket by removing only one circlip. Changing the chain sprocket is very simple: you can change the. STIHL 180 on your own. video, tips from mowers for grass.

The question of how to remove the clutch clutch on a chainsaw arises as often as the urgency of replacing the part itself. DIY Blog Repair of STIHL 180 chain saw. photo-report (Part 1).And make sure there is vacuum coming from the small hole with the carb removed.Did you fix it or not??Because when I was shopping for a saw they told me STIHL was better than Husqvarna. Chainsaws are equipped with a clutch centrifugal type, which is triggered automatically depending on the number ofThe latter prevents snow from getting into the air-cleaning system and is used only in winter, at positive temperature it is removed. How to remove the clutch from a chainsaw part 2. 01:56.

STIHL MS 250 chain saw clutch repair. 09:54. How to change a chain sprocket on a Partner? 03:38. How to open the STIHL MS-180 chain saw clutch. 01:08. Where to use: All STIHL chain saws. 16. Clutch clutch.To replace the sprocket it can be removed by removing just one of the circlip rings. Changing the chain sprocket is very simple. How to fill STIHL 180 chain saw oil (STIHL 180).16:53. After checking the oil supply to the bar everything works fine, no leaks in the hose, with the bar removed the oil flows out of the channel. Troubleshooting a Homelight carburetor. How to remove the clutch on a STIHL MS 180?Take your chainsaw to the nearest authorized service center for inspection. Homelight carburetor malfunction. How to tell the difference between a STIHL replica 180 and an ORIGINAL. Made this video for people who are about to buy their first chainsaw. STIHL 180 chain saw Disassembly STIHL 180 chain saw repair with my own hands. The STIHL MS 180 chain saw is designed for inexperienced users to operateAfter removing the muffler, you will be able to visually assess the condition of the cylinder and piston assembly by looking through the opening from the muffler. I do so-take a rope and knot it with a distance of about two centimeters, then unscrew the candle and shove a rope in it (this is to lock the crankshaft, otherwise you can not unscrew it), and you can unscrew it all. Husqvarna chain saws have one clutch spring and two weights, STIHL chain saws have three clutch springs and three weights (cams, sectors).How to remove the clutch chainsaw.Can you tell me what should be the play of the clutch on the axis. Good afternoon, dear readers, I am. Andrew Noack. In this article I decided to tell briefly about how I made a repair chain saw STIHL 180 with my own hands. In fact, this story is like a whole mini adventure that happened to me on vacation. The chainsaw clutch is on every modern tool.of the tool to be repaired, the clutch puller and remove the clutch Remove and carefully inspect the drum, mechanism parts. This task is faced every time there is a need to remove the chain saw drive sprocket and (or) clutch.- on some models (Stihl 180 in particular) there may be a washer between clutch and drive sprocket cover. How to remove the clutch from a chainsaw part 1. Duration: 3:10 Vitos 2 613 views.How to remove the chain saw clutch. Duration: 3:05 FREZZA Service 1 581 View. The chain on the chainsaw bar is driven by the drive sprocket connected to the engine gear. The wear of the spline on the sprocket indicates that it needs to be replaced as soon as possible Algorithm of the clutch drum replacement. Chainsaw clutch covers sprocket.On a STIHL chain saw for example, you might find a washer between the sprocket and the motor. You need to remember its position, remove and repeat The popularity of the chainsaw “STIHL 180” is due to the reasonable price and excellent performance.In order to identify the problem, you need to remove the cover from the carburetor and a special screen that is located behind the drum of the tool. How to remove the clutch from a STIHL 180 chain saw? To remove the clutch drum, remove the circlip, possibly with a simple slotted screwdriver. For removing the clutch you need a 19 mm wrench and a special piston stop. In the photo you can see a variety of models from manufacturers STIHL, Husqvarna, Partner, Goodluck.chain saw clutch.How to remove. The drive sprocket also serves as the drum. Top. Den1309 Blog Disassembling a STIHL 180 chain saw.Removing the tank lids. Remove ignition coil by removing a couple of screws. Full size. Removing the ignition coil. Saws. STIHL 180 chain saw repair manual.To see it, it is necessary to remove the cover from the carburetor and twist the special screen, which is located behind the drum of the chainsaw. STIHL chain saw MS 180 is mainly used for cutting wood and doing odd jobs in construction. This kind of equipment is used very often due to the large list of functions and features. The STIHL MS180 chain saw is not the cheapest model to maintain and has some factory defects, but it is lightweight, compact and high-speed. It’s easy to operate. Let’s remove the breaker, unscrewing two 19 nuts with a spark plug wrench. How to take the flywheel off a Chinese chainsaw?Be warned. there are plenty of fakes on the STIHL STIHL MS 180 chain saw. watch the video to make sure you don’t fall victim to fraud. Many chainsaw owners don’t think about how to remove the clutch on a chainsaw on their own, because they have the option of going to a service.Unscrew clutch clockwise. The fuel filter is dirty. Remove the fuel hose and check for fuel leaks. If the jet is weak, you may need to clean the filter.Hi, I have this question. STIHL chainsaw, when started at idle rpm works better than new, but Where to use: all STIHL chainsaws. 16. Clutch clutch.

How to change the clutch on a chainsaw?

Owners of chain saws probably wondered more than once. how to change the clutch on the chain saw? On most chainsaw models the removal and replacement of the clutch can be easily done manually by the owner, on few models unscrewing the drum can only be done in the workshop (those are, for example, Husqvarna 137 or Partner 351).

Disassembling chainsaw clutch

In this review, we will learn how to remove and replace the clutch on a chainsaw yourself, when to do it and what tools you may need.

Replacing the clutch

When replacing the clutch, we do not recommend using metal or plastic objects as a stopper. The former can scratch the cylinder, the latter can litter it.

• Engage the chain stop brake, remove the protective cap, and remove the saw headset;
• Remove dirt, sawdust, dried grease, if any;
• Remove the air filter and spark plug;
• Using a spark plug wrench, unscrew the spark plug;
• Rotating the crankshaft, bring the piston to the upper point, then withdraw it by 6-9 mm;
• With a rope, 7-8 mm in diameter, stop the piston in the upper position;
• Unscrew the nut on the clutch with a wrench.

Most chainsaw moving parts, have right-hand rotation. That’s why the nut on the clutch has a left-hand thread. Remove the cover by turning the spanner clockwise. Do not perform this operation with a hammer and chisel. you will break the edges!

• Remove the cover and drive sprocket. We diagnose malfunctions and estimate the wear of parts. Evaluate the condition of the needle bearing;
• If necessary replace parts with new ones (the drive sprocket needs it most often);

Mounting the chainsaw clutch system is done in reverse order, but you should pay attention to some peculiarities.

Installation of clutch system nuances:

• On some chainsaw models there may be a washer between the drive sprocket and the clutch. Note which end of the sprocket faces the engine;
• Some oil pump drives are equipped with a special spring (washer), which is responsible for transmitting the rotary motion from the drive sprocket to the oil pump. it is important to adjust the spring so it fits the free end (whisker) into the proper slot on the sprocket housing. Otherwise, the saw headset will not lubricate;

Important: Always check the automatic oil feed system after disassembling and reassembling the clutch.

How to Disassemble the Clutch?

The figure shows a simple chainsaw model with the main parts and assemblies.

To disassemble the clutch, proceed as follows:

• Remove the saw headset;
• Remove the chain and bar;
• Unscrew the air filter cover and carefully remove the spark plugs;
• Put the piston stopper in place;
• Use a puller to remove the clutch;
• Unscrew clockwise the clutch;
• Remove the drum and put a new one in.

Reassembly is done in reverse order.

How to remove the handle on a STIHL 180 saw

To fix either the reel or the drive sprocket, the operator will need to remove the clutch from the chain saw.

The procedure should be as follows:

• The first step is to loosen the chain and remove the entire chainring;
• Next, the operator must remove the air filter and the plastic cover of the standard clutch housing;
• After that, you will need to lock the crankshaft. as a result, it must remain stationary during the removal of the factory clutch. To block the crankshaft, you can remove the cover of the starter housing and insert 2 small metal bolts into the rotor provided in the ignition system device. The second option is to dismantle the spark plug, followed by lowering the piston and its blocking. Most often a roll of thin rope is used for this;
• Then you can proceed to removing the clutch itself. To do this with the tool provided in the saw kit or with a wrench for maintenance of an angle grinder, the clutch must be carefully unscrewed in the direction of the clock hand. It is important not to tear the mechanism from the threads;
• Next you have to dismantle the drum and the drive sprocket;
• The next step is to install a new clutch and screw it on the thread against the clock hand up to the stop. To do this, you need to lock the crankshaft again. Otherwise there is a risk of breaking the starter, located on the opposite end of the crankshaft;
• After that, you need to reassemble the clutch on the chainsaw and finally tighten it. This requires moving the recoil brake handle away from you, starting the chainsaw engine and quickly returning the brake lever to the opposite position.

Chainsaw guide bar length. Need to Consider?

Quite often replacing the chain clutch, including Champion 242, is due to the fact that this part can burst. And the reason is simple.

All modern chainsaws are equipped with a chain brake, and in most models it is controlled by a belt located on the tire cover and the chain surrounding the clutch drum.

If the user does not disengage the chain brake in time, but instead continues to pull the throttle trigger, the tire cover and chains will melt, causing the clutch drum to burst. In this case, the repair of the chainsaw is inevitable.Consider replacing the clutch drum using a Champion 242 chainsaw as an example, which is completely self-executing.Replacing the clutch drum is done in several steps, and we’ll look at each of them:

• Remove air filter cover.
• To unscrew the nuts that hold the clutch structure on the crankshaft, you must stop the engine. To do this, remove the cap from the spark plug, turn it and insert a rope into the spark plug hole. Then gently pull the starter handle to remove the remaining space in the combustion chamber. It is not recommended to use a metal plug, as the crankshaft can be turned while unscrewing the nut.

In this case, the piston will take the rope, and the stopper will break its bottom.

Tips: How to remove the sprocket from a chainsaw

Many tools need consumable parts to be replaced all the time. This also applies to saws. 3 self adjusting the carburetor carburetor on a Partner 350 chainsaw. How to remove the clutch to remove the clutch on a chainsaw, with my Chinese.

That’s why the question of how to remove the chain saw sprocket with a chainsaw, which is also often referred to as a clutch disc or centrifugal mechanism, is very popular with home masters.

In this regard, we need to look at what is called a sprocket and for what purpose it is needed.

The clutch drum, called the sprocket, is an integral part of the chainsaw.

The process of clutch repair is composed of these operations:

• To disassemble the chainring, the air filter flaps and the clutch itself;
• stop the crankshaft. to do this, simply unscrew the ignition plug;
• unscrew the clutch with a special wrench in a strong clockwise or counterclockwise motion (different models of saws can have both left and right-hand threads). Usually the tool to remove the clutch is included with the chainsaws;
• proceed to disconnect the drum and sprocket;
• If on examining the clutch one or several cracked springs are found (there can be several, for example on Husqvarna chain saws. 3 pcs.). it is necessary to replace the failed spring with a new one;
• Assemble the clutch on the chainsaw, put it in place and screw it in. Don’t forget that the crankshaft should still be stationary;
• Reassemble the dismantled parts on the saw in reverse order to disassembly;
• lock the clutch. the auxiliary brake handle pointing forward, start the device and carefully remove it from the inertia brake.

Disassembling the STIHL STIHL MS 180 chain saw. Remove the flywheel, ignition module and clutch.

In order to remove the clutch from the chainsaw, you must first be careful not to damage anything unnecessary.

This operation should be performed according to the following algorithm:

• Remove saw bar and chain. To do this, unscrew the manual chain brake by pulling the handle toward you. Then dismantle the tire and remove any dirt.
• Remove the covers from the air filter and clutch.
• Lock the crankshaft. This is a necessary procedure to avoid it rotating during operation. Unscrew the spark plug, fix the piston at its lowest “dead” point and put a rope through the spark plug hole.
• Use a special wrench to remove the clutch. Unscrew it clockwise because it usually has a left-hand thread.
• Replacing Damaged Parts. Reassemble the chainsaw clutch in reverse order of disassembly.

On this Champion saw, we eliminated the play of the drive sprocket and changed the main sprocket. The cause of the breakdown is the chain.

One of the most important parts of any model of device is the clutch. This mechanism requires constant monitoring for proper operation. Periodically remove it for inspection and necessary repairs. How to remove the clutch on a chainsaw of any brand correctly and how it is arranged let’s understand below.

Replacing the clutch

When replacing the clutch, do not use metal or plastic objects as stopper. The former can scratch the cylinder, the latter can litter it.

• Engage the chain stop brake, remove the protective cover and remove the saw headset;
• Remove dirt, filings, and dried lubricant, if any;
• We remove the air filter and the spark plug;
• Use a spark plug wrench to unscrew the spark plug;
• Rotating the crankshaft, bring the piston to the upper point, then withdraw it by 6-9 mm;
• Stop the piston in its upper position with a 7-8 mm rope;
• Unscrew a nut on the clutch with a special wrench.

The chain saw has most of its moving parts in right-hand rotation. This is why the nut on the clutch has a left-hand thread. The cover should be removed by turning the key clockwise. Do not do this with a hammer and chisel. you could break the edges!

• Removing the cover and the drive sprocket. Diagnose malfunctions and assess the wear of parts. Evaluate the condition of the needle bearing;
• If necessary, replace the parts with new ones (most often the drive sprocket needs it);

Reassembly of the chainsaw clutch is done in the reverse order, but you must take note of a few details.

Handwheel removal

The flywheel chain saw STIHL 180 is screwed with a lot of force, so to remove it you will need a head with a metal screwdriver. The nut that holds the flywheel is unscrewed with a 13 head.

To block the crankshaft from turning, you need to unscrew the plug and through the spark plug hole install a piston stopper, if it is not available, you can use an old starter cord, with knots tied to it and immersed in the cylinder through the spark plug hole.

categorically forbidden to keep the flywheel from turning by installing between his ribs and the body of the power screwdriver and other tools, with this method of blocking against rotation, the flywheel blades are not able to withstand the load and break.

After the piston is locked in the cylinder, the flywheel nut can be unscrewed. The thread in the nut is common, so turn it to the left side. After loosening the nut there is no need to remove it completely, it is enough to unscrew it until its upper edge is level with the tip of the shaft, and then set the soft metal hammer on the nut and make a sharp blow on it. By doing this, the flywheel slips off the shaft and can be removed easily without using any additional tools.

Removing the flywheel

The flywheel of the STIHL chain saw 180 is screwed in tightly and therefore requires a metal screwdriver to remove it. The nut holding the flywheel can be unscrewed with a 13 head.

To block the crankshaft from turning, you need to unscrew the spark plug and through the spark plug hole install a piston stopper, if it is not available, you can use an old starter cord, with knots tied to it and dipped into the cylinder through the spark plug hole.

Strictly prohibited to keep the flywheel from turning by installing between the ribs and the body of the power screwdriver, and other tools, with this method of blocking against rotation, the flywheel blades can not withstand the load and break.

After the piston in the cylinder is locked, the flywheel nut can be unscrewed. The thread in the nut is common, so turn it to the left side. After loosening the nut it is not necessary to remove it completely, it is enough to unscrew it until its upper edge is level with the tip of the shaft, and then put a soft metal hammer on the nut and make a sharp blow on it. This allows the flywheel to come off the shaft and be removed easily without using any additional tools.

Disassembling clutch and oil pump drive

, it is necessary to dismantle the drive sprocket. To do this carefully remove the washer from the grooves on the shaft and remove the sprocket and needle bearing.

READ How to unscrew a small screw without a screwdriver

Using a 19″ high crown, unscrew the clutch

The thread on it is left-handed, so it unscrews toward the bar, not the back of the STIHL 180 saw.

, You must immediately remove the deflector plate and the oil pump drive, and it is easy to do so because. к. they are put on the shaft without any fastening.

About washing

In this article we take a look at STIHL chain saws, how they work and what they do

Features of STIHL saw disassembly and assembly

There are a few other points to consider when disassembling a STIHL saw, one of which is that the handwheel must not be locked in place by screwdrivers, bolts or other improvised means. This can cause its blades to break. Only use the locking mechanism as shown in the diagram. About how to disassemble the STIHL 180. we told you, but there are nuances of reassembling a power saw:

• on the connecting rod we install the piston, to the left of which is the side of the crankshaft where the flywheel will be;
• put the piston back in the cylinder. Regarding elements like retaining ring, bearings or oil seals, then we place them on the shaft and place them in the appropriate place of the cylinder;
• Degrease the crankcase and its seating, lubricate with sealant and fix with 4 screws.

These are the nuances of the reassembly of the engine, which may cause difficulties (if you disassemble it), all other parts are assembled in reverse order step by step. Don’t forget to check the installation of the rod on the carb, the connection of the ignition wire. Also, all the nuances can be viewed in the video. KosiKosa gasoline tool store is glad to offer all its knowledge to each of our readers and customers.

The device of the oil pump

The first thing that comes to mind for a chainsaw holder who notices malfunctions in the oil feed pump is where to look for this assembly? It is located where the drive is, on the same side, right on the crankcase. this part is hidden behind the main sprocket. Its design is easier to disassemble, guided by the working scheme of a particular model.

So if you need to find and repair a STIHL 180 chainsaw oil pump, for example, please refer to the instruction manual for that model. In general, of course, the principle of the oil pump is the same, although on each model of the tool may look different.

How to remove the clutch on a STIHL 180 chain saw

When storing engines for extended periods of time it is important to prevent corrosion inside the cylinder-piston group. To prevent such undesirable processes, in addition to other operations, it is desirable to achieve a closed state at the intake and exhaust valves. В.

Chainsaw. How to unscrew the clutch.

It’s not unusual for tool owners to encounter breakdowns caused by improperly unscrewing the clutch. How to do it in general is described in the article

Generators. Types and Types

This article is about the types and kinds of alternators, their classifications and two special cases. This article will be helpful to those who choose equipment for their tasks: having information.

Generators. An Introduction to Stress Types

The most important thing that I have tried to convey in this article is the understanding that when selecting the power of the generator, you must operate primarily with indicators of starting currents and maximum voltages. Why?

Generators. How to use it

This article provides the most general recommendations for operating alternators, as well as common difficulties and mistakes

Chainsaw. How to unscrew the clutch.

Often there are failures caused by improper actions of tool owners when unscrewing the clutch. How to do this in general is described in the article

This task is faced every time there is a need to remove the chain saw drive sprocket and (or) clutch.

You can find a lot of video and text material on the web on this subject. This is not difficult to find if you want to. It is always a good idea to look up the information in the owner’s manual of the tool.

Each saw model has its own specifics in carrying out this procedure. That’s why let’s describe this process from a general idea point of view.

The chain brake cover must be removed. Pull the brake lever toward you to begin. This is to ensure that the brake lining does not touch the clutch cup. Then loosen the two nuts holding the cover. Loosen the mechanical chain tensioner. Release the tension in the chain and guide bar. Then loosen the two nuts and remove the chain brake cover.

Remove the bar and chain and remove any debris if any.

Remove the spark plug from the spark plug hole in the cylinder.

Next, secure the piston in the cylinder. To do this, rotate the clutch, watch the piston move upwards. In most cases, once the piston overlaps the exhaust port, drop any suitable rope into the spark plug hole in an amount sufficient to prevent the piston from moving further up. It is possible to strengthen the effect on the rope to tie simple knots. Remember that the rope has to be pulled back later. So don’t miss the other end