How to change the trimmer line in a Bosch trimmer

Which grass trimmer is better Bosch or greenworks

Bosch ART 26 SL grass trimmer (0.600.8A5.100) customer reviews

Svyatoslav P. Advantages: Lightweight, small package, easy assembly, works well in its “weight” category.Disadvantages: for tall people is not very handy. short.line for the trimmer, coming with, trash.comment: The device was purchased as a supplement to a lawn mower, but sometimes it is used instead of it. The box with the purchased trimmer easily fits in the trunk of a car. Initial assembly is easy, no special skills required. The quality of materials and workmanship are top-notch. Bosch is Bosch.Further on the work: the lawn and small grass mowing fine, but worth to go to the virgin soil and immediately realize that this model is not for it. Drowned. As a result, mows and clearing virgin land, but the effort it takes incredibly much, and if the virgin land more than one hundredweight. this model is not for you.The second minus for me was in the line. it “ran out” after 4-6 mowing. junk. In the end, I bought a line for the trimmer from a Chinese manufacturer (whether hammer or dde) 1.6 mm thick for a penny and forgot all about this problem.Another minus. the manual. I understand, of course, that all want to eat, but in the instruction nothing explanatory about service trimmer for grass: as to wind up a new fishing line for a trimmer elementary, I already keep silent about whether it is necessary to add/change oil. welcome in company service In general, it was necessary to understand it myself the Minus is not critical, but all the same The result: Decent and qualitative device for an adequate price. Powerful enough for lawn and small amounts of virgin land. It worked well during the season. And despite the faults, I would give this device 5 points for sure.

Sergey R. Advantages: Lightweight, maneuverable, low-noise. It folds up to the size of a plastic bag. I would not recommend folding it all the time, though, as it is not convenient.Disadvantages: Of course. the power, trimmer line does not contribute to mowing perennial grass and thick burdock. Short wire.comment: Maneuverability thanks to the small size really helps. For example I had to mow the grass between the piles of the frame house. Very convenient to work around the piles, because of the short handle it fits everywhere.Power, trimmer line, not conducive to mowing perennial grass and thick burdock, but takes them in a few passes. Low power can be called a virtue. Unlike its powerful gasoline and electric counterparts, it is low-noise. When I’m mowing, I can listen to the radio through my headphones. The grass trimmer’s short wire is immediately designed for an extra extension cord. So should buy it too.My conclusion: The purchase is justified. If you have a small area or a lot of trees and bushes and other inconvenient obstacles, this thing is very useful. Don’t let the small power fool you, it’s quite sufficient for most needs of a small area with difficult terrain.

Bosch AFS 23-37 Grass trimmer (0.600.8A9.020) customer reviews

Advantages: As a home electric mower it is worth enough.Powerful. Light. Quiet. Universal.Disadvantages: Trimmer lines are very expensive.comment: The main drawback is that replacement lines are very expensive.Took another star off for this.A 10-pack costs around 1000, t.е. It costs 100 for one 37 cm long trimmer line.A roll of fishing line of about the same thickness costs about 110 for 15 meters.So replacement lines are 36 times more expensive than the reels.This is insanely overpriced, I have to make them myself.

Oleg I. Advantages: German-made cleverly powerfulWhisper quietNormal priceDisadvantages: The line for the trimmer is thick for thin grassIncompatibility only with proprietary fishing linesLegal protection is narrow for working with fishing line. from time to time pieces of grass fly in the face. I have to use a mosquito nets.comment: I have used it only once so far. Bought, mowed a plot of about 10 acres. The area is uneven, hills, rocks. a lawnmower is not an option. The seller said: do not put too much weight on it, just mow for 15 minutes and let the engine have a rest. I checked the instruction manual just in case. there is nothing like that. I went to mow and mowed for 3 hours, with pauses only to drag the spool. Was not warm at all, just a little warm.The quality of materials is good, about a long handle: it can be turned to the other side by 180 °. If I’m right-handed, it goes to the left, and then nothing obstructs it.The line for the trimmer is so bad that I almost never used the knife. it tears everything, including the two-year-old shoots of willow and dog rose. While mowing, did not change once. after three hours there was about half of the length left.I hardly used the knife. I cut some bushes and took them off (no rocks in the tall grass). The line is enough. In fall the knife can be used for roughing bushes.Thin, creeping grass, dense bumps are taken with line rather difficult, often become braided, sometimes it is possible to skip it with idle spinning, sometimes not. The lack of power is not felt, for well-groomed areas that mow every 2 weeks, this model is even redundant.At last, noisiness: does not work loudly. If you do not want to annoy the neighbors and your own household with crackling, take it.In general, the impressions so far are positive. If anything breaks, I’ll write.

Bosch ART 23-10 grass trimmer.8 Li (0.600.8A8.100) customer reviews

The advantages: I like the principle. cordless trimmer for grass. Was even willing to put up with a short battery life. 15-20 minutes. Easy. The handle adjusts to the height of the user.Disadvantages: What a disappointment. the grass winds up on the shaft. You mow for 15 minutes and then you have to service it for an hour. Don’t buy this model!Comment: Was a fan of this brand. Never failed before. I had my suspicions a couple of years ago when I swapped my perfectly serviceable washing machine for a new one. It’s also Bosch, but it doesn’t wash as well. Either the technology “piercing” did not hold, or the control software is not successful. And now this mower, my ass. Where have the Bosch engineers gone?? East Europeans have been replaced or something? Gone are the representatives of the old engineering school? In general, they should have thought to put a thin shaft on the grass trimmer, a disc on it, and a petal on the disc. In the end, the grass, if it is not a plantain, winds up on this shaft like thread on a spool. Worse, this shaft is sticking out of the plastic body trimmer for grass with a gap. Т.е. It is possible to unwind grass somehow, to cut it, but it is not so easy to take out the grass, which has come round and has stuck in the gap under the housing. It builds up there and starts to slow down the rotation. Who has seen how drum brakes are designed on a car, will understand the principle. You have to take off the disc with the blade and pull out a blade of grass. Oh, where is this old reliable stuff from Bosch.?

greenworks grass trimmers and reviews

grass trimmer greenworks 1301507ub G-MAX 40V GD40BC4 customer reviews

Vyacheslav t. Advantages: Maneuverability in terms of “pick and mow” Disadvantages: Ergonomics. After the Echo, the shoulder strap sucks! The engine is very quiet and does not cause unnatural grasping all the timeSuggestion: less noise, less vibration, the engine does not bake on the side in the heat. Although after an hour of work, my hands are also sore. When it is necessary to work intermittently and go to another place, just let go of the trigger and the machine stops. Push it, it works. The power is enough. On a fishing line. I do not mow with a knife, so I have nothing to say

greenworks 2100007 24V Deluxe grass trimmer customer reviews

IgorA. T. Advantages:. light weight. clever design. with a fully charged battery has enough power to cut down fairly thick stems sarnikovDisadvantages:. 2Ah battery sat down for 10 minutes, while zyaradka at least 45 minutes. Enough for one hundred acres of densely overgrown land at most.- After work, it is impossible to charge the battery immediately after work, you have to wait until it cools down, the automation will not let it chargeComment: As a basic tool for mowing lawns on large areas is not suitable. If you use it as a basic battery, it is necessary to have 3-4 4Ah batteries, but their cost is high. If you need to mow or clean a small but overgrown area of 1-2 hundred square meters, then 2 batteries 2Ah will do.

grass trimmer greenworks 21107 G-MAX 40V customer reviews

Dmitry N. Cons: battery life, low noise, overall build, plastic, runtime.Disadvantages: NoComment: Great trimmer for the grass. A small site is small, so I don’t feel like mowing or pulling a wire in the morning. The battery retains well, the grass trimmer does not sag under load. Simply press the button and you’re ready to go. No noise, you can mow in the morning with peace of mind. Easy-to-use wheels to mow along the curb.

Sergey I. Advantages: First of all, it weighs less than a gasoline grass trimmer; secondly, there’s no cord, so you can mow anywhere in the yard; thirdly, different cutting angles are installed and you can turn it to mow along the curb and paths. 2 Ah battery lasts up to 40 minutes. 4 Ah for almost an hour and a half. No exhaust and noise of gasoline grass trimmer.Disadvantages: No disadvantagesComment: The power of this grass trimmer allows you to mow even burdock stems and small brushwood. Of course, it’s better suited to areas without a large, continuous lawn. For a large lawn, wheeled grass trimmers are definitely better, only they allow you to mow the lawn evenly. And for mowing around trees, around buildings and in difficult places, it’s the perfect model. Other than the price. I bought it with the battery and charger for 6490.

Grass trimmer greenworks 23017 230V customer reviews

Ivan Muravyov Pros: Low weight. Easy to use (the plug has a small wire). Includes a shoulder strap.Weaknesses: I don’t know yet how to change the trimmer’s line to a disk.comment: I recommend to buy. Just tell me how to change the line for the trimmer cutting disc.

weed trimmer greenworks 21117 280W customer reviews

Eugene T. Advantages: Low price (I bought it for 980 ), nice color, pretty handy button (well, compared to my old one, where it was double)Disadvantages: Tears trimmer line, overheats, flimsy boom design, soft plastic quickly gets scratchedComment: Trimmer line tears because of single-braided reel design. When starting/stopping, the trimmer line overlaps and the coils stick. The only thing is that with a round line, it happens a bit less often than with “squares”, “triangles”, etc.п. Т.е., If “squares”, “triangles” cannot be used from the word “at all”, then round, twisted line can still manage to mow out a couple of meters. In the old, double line, this problem in many years has never been observed at all!The reason of overheating was found out after disassembling. the bearing was spinning freely as in a spinner and “murmuring” The rod has an unusual design, reminiscent of a folding cane for the visually impaired. It’s easy to assemble/disassemble, but you won’t need it more than once in your lifetime. The plastic of the handle is not suitable for garden equipment. there are deep scratches during the couple of mowing sessions, it doesn’t bother me, but it looks ugly:(Resume. I adapted the reel from the old one, replaced the bearing (brand-name, Japanese, 100 ), after that it works fine, so I put two stars instead of one, even though I understand that the vast majority of buyers will not be satisfied with such a variant. I have never bought a car that I don’t need, and I don’t need a car that I don’t trust. Yes, and whether many can do such alterationsp.s. I saw by chance that the exact same grass trimmer (but of course in a different color) is sold under the brand Interskol (and more Bosch, I think), friends, be careful, do not make a mistake!

greenworks 2100007a 24V Deluxe G24ST30MK2 grass trimmer customer reviews

Yuri Sh. Advantages: Interesting model, interesting thing, for a neat mowing the lawn.Weaknesses: need to add spare spools to the kit.comment: was not delivered on time as scheduled, just was not put in the delivery truck, and was only needed on that day. Was bought in another store.

greenworks grass trimmer 1301507 G-MAX 40V GD40BC customer reviews

Alex Ivanov Advantages: Power, additional blade for tall grass (brushwood) Disadvantages: Heavy, shoulder mounting is not very good Commentary: First of all, it should be noted that this is a really powerful cordless trimmer for grass. Due to the blade it can deal not only with grass, but also with thistles.It is used by me as an additional tool for the garden care.Battery 2 Ah enough for about 15 minutes. just enough comfortable time. The heaviness of the grass trimmer will have an effect afterwards.Well made, overall happy with the product.

Eugene P. Advantages: I have been using this tool for about two months. I like it more and more as I get used to it. The power, of course, is not the same as that of good gasoline trimmers, but with a motley grass to a height of 20. 25 inches quite cope. Makes “no noise and dust”, slow but clean. Two batteries (2 4 Ah) are enough for me for about an hour and a half, if I do not use the Turbo mode.comment: The process of charging the batteries is pretty long.

How to change the line for the trimmer on the trimmer?

Grass trimmer line replacement with step-by-step instructions will allow even an inexperienced in such matters lawnmower owner to perform rather complicated work.

However, before you begin work on replacing the fishing line on your trimmer, you need to ensure that the work is done safely. In particular, take precautions to prevent the lawnmower from being switched on carelessly or unintentionally:

• to exclude spontaneous start,
• remove the battery pack (if used),
• place the tool on a comfortable place to work.

Grass trimmer line replacement work is convenient when the mower is lying on the table, and the master, who performs the grass trimmer line replacement, has the opportunity to approach the tool from any side.

Removing the grass trimmer head cover

The first step of disassembly is to remove the cover of the grass trimmer head. By the example of models of trimmers “Black and Decker” and others, to remove the cover is usually enough to apply some force to unlock the latch-lock, which are located on the side of the head body.

On some models of lawnmowers initially provides for the dismantling of the grass trimmer head, for which the hexagon wrench included in the tool kit is used. The head is usually held by two or three screws, which are accessed through the side holes of the rear decorative cover.

The head cap, where the line reel is mounted, is normally held in place by a latch tongue. It is enough to squeeze the tongue-latch with some effort and slightly turn the cover, after which the cover is easily removed At the moment of squeezing the tongue-latch should be slightly turned and lift the cover of the grass trimmer head to remove the winding drum.

Step Two: Removing the spool (spool) of fishing line

The next step in the process is to remove the winding drum with fishing line from the inner area of the head. You need to turn the head with the open side to see the line for the trimmer and the spool. On the side of the head find two recesses (eyelets), through which the line for the trimmer is led out.

The line for the trimmer should be released from the holes by turning the reel. then carefully remove the spool from the head area. The winding drum of some models is mounted on a spring. This point must be taken into account when performing the extraction operation.

Procedure for extracting the grass trimmer fishing line spool from the inner area of the head: 1. head complete with spool; 2. extracting carefully with a small axial rotation; 3. extracted parts The old trimmer fishing line is completely removed from the spool. To remove the old line of the grass trimmer, you need to remove the line from the loops and pull the free end. This method removes all the old winding. The same process is repeated on the second section of the drum. It is recommended that the technician wear gloves when performing the work.

Types of trimmer heads

Grass cutter head is a cylindrical body, in which a spool with a fishing line (cord) is installed. This design can be installed on both gasoline and electric trimmers. The heads differ in the way the cord is threaded and fed and come in 3 types.

• Automatic. The filament feed is performed after the user has lowered the engine speed. Automatic line feed is useful, if a large amount of work is involved, but such bobbins have a disadvantage. high thread consumption.
• Semi-automatic. This type of mowing head requires no complex manipulation on the part of the user. How they work is designed so that the cord is lengthened automatically while the machine is running at full speed. It is enough to slightly knock the grass trimmer head on the ground (this removes the cord lock), and the line for trimmer thanks to the centrifugal force is pulled out of the bobbin, then cut to the right length by the knife located on the protective cover.
• Manual. Extending the cord requires stopping the machine and then pulling the trimmer line manually.

On the basis of the above, semi-automatic bobbins are the best choice. Also keep in mind that grass trimmer reels for grass can be single string (used only for trimming grass) and double string, which are used for mowing tall grass and small, with thin stems of bushes.

You can see the video

A Quick Tip. Make sure that your hair does not come into contact with hard objects when cutting. This contact will cut the line for the trimmer. And since the grass trimmer doesn’t come with this trimmer automatically, you’ll have to stop work every time, remove the spool, and release the trimmer line again.

Thick hair

It is stored in the upper part of the grass trimmer body.

Spare spools for storage

Such a line for the trimmer in the spool is very simple to install. on the inner circle inside the spool. Insert the center of the hair growth line with the metal attachment at the top of the spool and pull the ends of the hair growth line along the grooves and out.

Reinforced fishing line for the trimmer

This spool is attached to the trimmer as well as the regular hair spool.

Winding the fishing line

Filling the fishing line into the grass trimmer reel is a relatively simple procedure, provided that you follow a certain algorithm of actions. When you need to determine how many meters of consumable material is enough, wind it on the bobbin so that the coil does not exceed the diameter of the sides. Once you have determined the cord length, follow these instructions:

• Fold the consumable material in half so that one end of the line is 10-15 cm longer than the other.
• Charging should begin with the center curb, which divides the grass trimmer bobbin into 2 parts. Find the groove where the cord should be inserted. Bend the last one in half.
• Determine which direction you want to wind the line for the trimmer. To do this, look closely at the bobbin, which may have an arrow or inscription. This indicates the winding direction. If there are no markings on the bobbin, then look at the arrow on the mowing head. conduct winding in the opposite direction.
• Make sure you wind the material carefully, coil by coil. Try to keep the thread as taut as possible.
• When you have finished laying the cord, fasten the short end of the material first. To do this, insert it into the groove on the side of the spool that fits the diameter. Attach the second (longer) end in the groove on the other side of the grass trimmer spool.
• After securing the line to the trimmer, cut the ends. Remember to leave a seam allowance of around 10 cm.
• Position the thread reel on the mowing head of the machine. To do this, alternately insert and tighten the thread into the output holes of the head to then place the device bobbin into the leather.
• With the required force, pull the cord out of the fixing grooves and tighten the material. When finished, put on the cover and secure it with the latches.

You can also wind the cord on the grass trimmer in another way, in which two pieces of material are charged instead of one. The change is made as follows:

• Bend one end of the cord to form a hook.
• At the bottom of the bobbin, there should be a hole that is designed to hold the fishing line. Insert the bent end of the thread there.
• Wind the cord material in the direction of the arrow to the desired level, which does not exceed the diameter of the grass trimmer spool.
• Do the same for the second cell of the bobbin.
• Assembling the head of the device is similar to the first method.

How to quickly remove the bobbin from the tool

Before the thread is wound on the bobbin, it must be removed. And the methods of removal depend on the characteristics of the tool. The trimmers with a motor at the ground itself has two side buttons, when you press them a part of the body is separated along with a device for winding the thread.

With a bent-rod tool, move the knob on the attachment counterclockwise; remove it and remove both the bobbin and the spring inside it. With straight boom trimmers use a screwdriver to fix it, turn it clockwise and remove it. Then the device is disassembled either with the help of latches or by moving its parts in different directions. The spring is removed from the coil.

Electrical faults

to detect faults in the electrical part, as a rule, mere inspection is not enough, a multimeter or at least a tester with a dialler is needed. These faults are usually characterized by complete motor failure, severe overheating or jerky operation.

Inspection begins with the power cable, if damaged it is either repaired or replaced. The express check involves checking the 220 volt voltage at the motor terminals.

Voltage should appear when you press the button, if voltage is present, you can safely say that the grass trimmer motor is defective, it must be disconnected and carefully inspected. Minor soiling of the collector plates and brushes is normal, but it is better to clean them with a soft cloth dampened with alcohol, with the obvious appearance of worn brushes it is better to replace them.

Using multimeter in resistance test mode (lowest limit is “ohms”) use feeler gauges to. Ohms) feeler gauges touch the brush contacts or graphite brushes themselves, the tester should not show resistance greater than 100 ohms.

If the resistance is infinite (one on the multimeter) try to turn the motor shaft without removing the feeler gauges. At the serviceable electric motor resistance will be approximately 10. 40 Ohm, if the brushes are not tested then there is no contact or integrity of the stator windings is broken, breakage or burnout is possible. If the resistance is less than 5 ohms, there is an intervidual short circuit, most likely caused by severe overheating of the motor.

To identify the specific cause of the motor failure, when the motor brushes are not tested, you can resort to the following procedure. The graphite brushes should be pulled out by pulling out the brass inserts or by removing the clamping springs.

Collector motors in these devices so arranged that the windings of the stator and rotor are connected in series, and in expensive models of motors in this series circuit is also connected and thermostat (110 degrees), such a relay in normal circumstances keeps the power contact closed. A separate diagnostic method is to check the resistance on the collector drum plates.

In order to identify the defect culprit, you need to remove the insulation in the form of thermoplastic shrouds, where the windings and the thermo-relay are connected, and to test each winding separately using a multimeter, as well as the thermo-relay itself.

Mechanical faults

The most mechanically stressed parts of an electric brushcutter are the bearings and the trimmer (the bobbin). In most cases, the device stops mowing the grass due to a failure of its filament spool

The line for your trimmer is out. According to the prescribed instructions, the line for the trimmer should be wound on a spool.

Trimmer line gets tangled. If the spool is undamaged, you need to cut or unwind the line for the trimmer and, if necessary, rewind the entire bobbin.

The filament is sticking to the trimmer. Because of the rather intensive work and overheating, the plastic filaments of the line can fuse with each other. You need to rewind the filament spool with new line and inspect the damage of the bobbin itself.

The motor is running, but the filament spool does not spin. Damage has most likely occurred to the filament spool. Places for fixing the bottom of the spool can break, you need to completely disassemble the bobbin and if necessary improve the mount or replace it at all. In most electric trimmers the bobbin is simply pressed by its plastic body to the motor shaft and if it overheats, the plastic melts and can turn or even fly off.

Both devices did not give any signs of life, when turned on the motors did not work.

The casing of both units consisted of two halves, the self tapping screws were on one side for easy disassembly. After all screws are unscrewed upper housing is separated from the lower housing by lightly pushing with a flat-blade screwdriver into the slot to open the interlocking plastic locks.

After disassembly proceed to examination of the internals and searching for faults.

During the inspection was found on the motor trimmer for grass Bosch, on one of the brushes, which is fixed by compression spring, broke off a copper wire that is naturally the cause of the lack of voltage on the brushes and the motor does not rotate.

The wire was put back in place and the collector pads were cleaned with a soft rag soaked in alcohol until they had a copper sheen. Brushes were in good condition and did not need to be replaced.

It was also found that the switch does not create a reliable electrical contact, we had to forcefully clamp the button, it was decided to disassemble the button, its contacts were cleaned of carbon deposits and lubricated with KONTAKT S-61 current protection spray.

With electric scythe GARDENER was not so simple, it was quite a long time in a broken condition, and in the literal sense of the word “broken”, its rod at the point of attachment of the motor housing was broken in half apparently so were heavy conditions of its use.

Using perforated plates of the metal profile fasteners the new fixing of the engine case to the electric mower boom was made not cunningly. Structure integrity was restored by reliable, if not aesthetic, method, because the main thing in the electric mower is its functionality.

The motor shaft was noticeably hard to turn, and internal inspection revealed burned manifold plates and worn brushes. The plates were sanded down to a shiny finish and the brushes were replaced with new ones.

In view of the long hours of operation without lubrication and the subsequent storage of the device in an aggressive environment bearings got stuck a bit and the motor shaft does not naturally rotate with difficulty. Engine bearings were washed with WD-40 spray and then lubricated. As a result the engine rotated noticeably better, but bearings were already “broken”, and when running the engine from the network the sound of its work was not so smooth and monotonous.

Further inspection of electrical part led to the button, it was broken from its mounting, even though it was pressed, but the tester showed its failure. The button is not demountable, so it was replaced by a new one. It was necessary to restore bindings with hot melt glue.

In addition to the broken rod was a crack in the plastic protection, someone might have dropped it badly. the grasshopper could also work with it, but it was decided, as far as possible, to restore the design of the protection.

Naturally just to glue such a heavily loaded and exposed to impact object would not be a safe solution. So with the same perforated plates from the metal profile two brackets were made which created a “monolithic” connection of the two parts of the cracked hull. The plates are riveted to the housing with aluminum rivets.

When the lawnmower was assembled it was found that the handle bar was loose and twisted at the attachment points of the handle, so the areas where the plastic tabs of the handle body pressed against the metal of the handle bar were additionally sealed with a strip of cloth tape. The design is now free of excessive backlash.

Can I mow wet grass with an electric trimmer??

Many people find this interesting, but is it possible to operate the machine in wet weather?? Experts do not recommend using an electric grass trimmer with or without wheels in rain and fog, especially if the engine is located below. There is a high risk of falling into water, but over-positioned models are best used in dry weather to reduce the risk of short circuits and other unpleasant consequences. In addition, wet grass is more precisely aligned with the cutting part, making it difficult to work.

• The playground should be cleared of foreign objects that can damage the trimmer line. Rocks, glass, wire, garbage dumps, and other orphaned objects.
• Plug in the electric device and charge the battery.
• Attach the tool to your shoulder or back, depending on the type of belt, and hold it with both hands.
• Press the button and start moving, guiding the braid from right to left.
• Done by pushing the switch.
• Remove the braid. The best electric lawn trimmers take apart and take up little space in the shed or garage.

How to Grease an Electric Grass Trimmer?

The tool should be lubricated from time to time. Experts advise to do it every 10-15 hours of operation of the device. Here’s how:

• The electric lawn grass trimmer has a technological hole in the top of the gear housing. You should find these.
• Remove the screw that acts as a plug in the hole.
• Insert 1.5-2 ml of thick consistency into the cavity of the.
• Rotate the shaft several times to make sure it penetrates all parts of the gearbox. Flywheel, starter coil and bearings.
• Before storing electric grass trimmers for the winter, clean and rinse the gears, remove old grease, and apply new grease. Taking care of the tool can greatly extend its life.

How to Disassemble an Electric Grass Trimmer?

Some owners fix their trimmers themselves. To do this, they need to disassemble the engine:

• All fixing screws are on the same side. Unscrew them with a screwdriver to separate the housing halves and open the “inner part”.
• Next, do the repair, which requires a powerful electric grass trimmer. Replace any mechanically damaged items with traces of high temperature.
• Put the two halves together and screw them together.

How to change the trimmer line on an electric trimmer?

The position of the grass trimmer head is very similar to the design of a sewing machine spool. To replace your trimmer’s fishing line, do the following:

• Remove the cover.
• Carefully pull out the spool.
• Remove the spring, if any, and unscrew the fastening bolt in the center of the body clockwise.
• It remains to remove the spool from the gearbox shaft and replace it.
• If you want to know how to insert the line for the trimmer into the electric grass trimmer, you should know that there is a special hole or groove in the reel for this. Inserting the rod into it, start winding the thread in the opposite direction to that in which the spool rotates during operation.

Defective electric grass trimmers

Why an electric grass trimmer gets hot?

There can be a variety of reasons for this. A small electric grass trimmer with low power and a smaller motor heats up very quickly, especially if it is driven mercilessly. As a result, parts of it melt and flow, covering the whole tool. There are many such “culebins”, who independently install a thicker line for the trimmer, attach knives, chains, and then are surprised that the device “does not pull”. I have always tried to buy grass trimmers with Bosch ART 30 CombiTrim.

Review: Bosch ART 30 CombiTrim Grass Trimmer. Hasn’t failed once in 11 years

We have a vegetable garden (some people call it a “dacha”) since 2000. The site is located close to the forest, the soil is fertile, and on such soil weeds grow abundantly and quickly. Especially if the weather is warm and rainy. There is no ordinary grass trimmer, and it is necessary to know how to mow correctly. A lawn trimmer wouldn’t do as well. We have an uneven terrain, a lot of bushes, trees, paths, the terrain is uneven. And weeds grow with trunks in the finger and height up to 150 cm. To ennoble our 8 acres can only trimmer grass.

I went to a construction material hypermarket to choose a machine with the thought of “How do I carry a healthy box in public transport?”At that time, the main criteria of choice were as follows: inexpensive, lightweight (I do not want to work heavy), not gasoline (otherwise there would be more hassle with a young nursing mother than a baby), a compact box (and here I did not go by cab out of principle, and the financial situation of the family was difficult). What do you want from a woman?? The electric one is fine. I can make an extension cord without any problems. Back at school we were taught how to screw the socket and plug to the cable.

At that time I had no experience with building materials, and had to listen to what the consultant tells me. The models had a lot of features, but the most important for me personally were power and the diameter of mowing. This diameter is encoded in the model name. The one I’m writing about. 30 cm.

I apologize for not aesthetically pleasing appearance, but it is a working process, and there is no point in washing it, because it immediately gets dirty with grass. The main specifications are listed on the nameplate: noise level 96 dB, power 500 watts, 11 thousand rpm, weight 3.43 kg. Well, the country of manufacture is not hidden. China.

I will begin to tell you about the device trimmer for the grass with his handle. You can choose any comfortable position if you loosen the red screw, and then you have to tighten it. I taught my 12-year-old son how to use the trimmer, so he could help us with the garden. And he complained that the hard handle was pressing against his palm. I had to wrap a cotton sheet around it. It absorbs sweat well, too. And I myself do not feel discomfort when I hold the plastic in my hand.

It is possible to adjust the length of the telescopic rod to the height of the person. The length is fixed with a red clip. I’m 5’6″, I’m comfortable. And if the lawn trimmer is much taller, you need to start by holding the grass trimmer in your hands at the store. Better yet, have a neighbor or friend mow with one of these.

The angle of the blade can be easily adjusted. There is a red pedal under the rod that you have to press with your foot, adjust the angle and release. This feature is handy when you mow under trees and on uneven ground. I use that a lot.

This is the path we have the S profile. And the angle of the block will be different, it depends on where I stand with my feet. In a low place or on a hill. Here is a photo of the grass after and before the mowing.

The grass cuttings are easy to remove from the lawn with a fan rake. They’re lightweight and don’t ruin the lawn. Good for combing out old dried out vegetation, grass clippings and dry leaves.

We have eight acres of land. I didn’t know exactly how long it was, so I bought a 30 m cord to extend it. This was my mistake as it was not enough to reach all areas. I had to make another one like this and plug it in extra. For exterior work use cable PVS. For grass trimmers, it is enough to use a two-core wire with a cross section of 1.5. Store it conveniently on a special spool, but I do not have one (they are quite expensive). So out of plywood made such a figure. There are plans to make at leisure more convenient, with a handle.

Modern single-socket sockets and euro-plugs provide a very strong connection, and even if you pull accidentally, the plug will not fall out of the socket. If there is no grounding in the house, and electrical installation products with grounding contact can not be used. Although they can withstand higher currents, and they do not cost much more. Do not use your trimmer or other power tools in the rain. Can cause a short circuit.

For safety, the grass trimmer plug has these clips for the wire. But I don’t use them. Wire with a plug of the trimmer for grass is short, that is, the connection point is close to the human body and piling electric wires will interfere with the work. Watch the location of the cable on the ground when working. Do not hit it with the fishing line.

This grass trimmer model is equipped with special wheels. If you adjust the grass cutting height and roll the machine across the lawn, it will be a fairly level lawn. The wheels are plastic, lightweight and do not interfere with normal mowing when the electric mower is suspended and pulled from side to side. They also help you mow under bushes and trees. But I do not use this method, as our grass is always high and requires a detailed approach. To save weight, I took them off.

– 4. Alexander J.

Pros:	Powerful motor. Mows well. You can use any other manufacturer’s trimmer line, you don’t have to buy the expensive Bosch trimmer line.
Cons:	Noisy. Heavier than others because of the powerful motor. To pull the line for the trimmer, it is necessary to remove the spool, unscrew the line for the trimmer to the desired length and then put on the spool.
Review:	–

– 5. Sobornova Sofia

Pros:	So glad! I mowed three hundreds of hundreds of human-sized, incomprehensible plants with it, I am overwhelmed with emotion! Now the area in front of the house is neat and tidy. Mows thick weeds, about 2 meters, with a diameter of about 1 cm in two steps (first half, then the rest), but at this point the problem with the line, it seems to overheat and gets stuck in the coil, I have to rewind! But it is nothing! I mean, if you mow regular grass, you don’t have any trouble rewinding. I am 43 kg and walking for 2 hours with this almost 5 kg trimmer does not bore me at all. Everything is quite comfortable. And even holding the start button all the time is not stressful at all. Asked the store clerks why there is no locking button or attachment, they answered. for safety reasons, and rightly so. The presence of power cable behind the back does not interfere with the process. Power is good. Has a carrying strap included.
Cons:	Frightening approaching line change.
Review:	–

– 5. pigolkin sascha

Pros:	Good trimmer. Bought 3 months ago all like it.
Cons:	Can’t see any downside so far
Review:	Good trimmer I would recommend to buy to my friends

– 5. Filimonov Oleg

Pros:	Powerful, fastidious, time to change only a line for a trimmer
Cons:	It is not convenient to change the line for a trimmer, although this may be so for all, it is heavy, but with the right setting of the belt the weight is not felt at all
Review:	Great model, I use it for more than 2 years, I do not do anything with it, only change the line for the trimmer, not once let me down. It mows like a beast, even grass, even bogs, etc., even with “asterisk” line.п. I use it every week, at a time I mow 4 hectares of land. Not once regretted the choice of the model. A roll of fishing line is enough for the summer season

– 5. Tolkachev Dmitry

Pros:	1. Reliable line feed mechanism. I don’t have any regrets, even if I choose this model, because the cutting line lasts much longer than in the previous trimmer (see pic! Comment) 2. Powerful. 3. Very well made.
Cons:	1. The trigger is not fixed in the pressed position. I have a great story with my hand-held tool, and it really allows me to use it with ease. 2. Pretty heavy. Requires some physical strength.
Review:	Very, very good trimmer for the grass. Before I had a PATRIOT ET 1200 grass trimmer that was very similar to this one. But there was a solid problem with the line feed. In fact, the trimmer line did not feed itself and every time it ran out, I had to disassemble and reassemble the head. And when I brought this grass trimmer to the warranty repair shop, I was told. “What do you do not take instead of this A normal Boschev grass trimmer. And after another year of agony, I finally made this. Conclusion: great trimmer for the grass. Satisfied.

– 1. The data is hidden

Pros:	power,price
Cons:	Broke
Review:	How can such a powerful grass trimmer be made of plastic??!Broke, I agree with all the negative reviews

– 3. Yaroslav S.

Pros:	Worked for 3 years. 10 acres of different grass, from lawn grass to harsh turnips and pawpaws. There is no problem with the engine. The overheat lock system works great.
Cons:	Twice the shaft was covered together with the clutch, which for some reason turned out to be plastic.
Review:	–

– 2. ivanov ivan

Pros:	When the machine is new. Works
Cons:	Extremely low resource reel assembly (bobbin) and design miscalculation in transmission.
Review:	Grass trimmer worked exactly one summer season. The splines in the lower “crankshaft” (a.k.a. The “gearbox” of other manufacturers). It is inevitable, because for the transmission of torque is used a shaft with a single flats and a lot of small parts, the breakage of which. It’s just a matter of time. Drivetrain cuts due to grass winding and not working temperature rebound scheme when the motor transmits torque and the bobbin is already locked.

– 4. Sadardinov Oleg

Pros:	Good power, enough to chop anything you want. Comfortable grip and strap included!
Cons:	Venting from the engine under the elbow blows. The line for the trimmer in the kit is not very good. No safety glasses included! Hand gets tired holding the button for a long time!
Review:	The second year I switched from gasoline to electric and have no regrets! Minus only in the wire but it can be solved by the stationary on the perimeter of the site (I have 30 acres) Grass loves any growth value does not matter))) The main thing is not to turn the plot into a thicket there and gasoline zabuhankanetsya!))) By the way on the power of 1000 watts is like 1-1.2 horsepower gasoline.

Cutting block attachment

The cutting block is a key component of the Philips Styler. It has short, sharp edges and is used to quickly and accurately trim the length of your hair.

To remove the cutting block from the body styler, check the presence of the body styler detach button. If it is there, press the button to remove the cutting block.

If the styler does not have an unclip button, place your finger under the cutter block and pull it out. To reinstall, slide the lower part of the cutting unit into the styler body, then slide the part with the teeth in until it clicks. Avoid straining too much. this can damage the appliance.

If you are unable to install the cutting unit, check for foreign bodies in the body of the styler and try cleaning it with a small brush or cotton swab.

No matter how well the electric grass trimmer we purchased worked on the dacha plot or a country house. Sooner or later the time will come when we need to remove the grass trimmer head for replacement or prevention. I should say right away that in order to conduct the replacement of the fishing line trimmer head does not need to be removed completely. Within this article, I will tell you how to remove or replace the entire mowing head using the example of the BlackDecker GL716 electric grass trimmer.

Tips and advice on how to thread a trimmer line and what you need to know

There are some useful tips and recommendations that will be useful to learn not only for beginners, but also for experienced masters. These tips will help prevent negative consequences in the form of injuries and improper functioning of the mechanism. These recommendations state the following:

• The cover must be inserted until it clicks into place. This is 2 or more clicks, depending on the number of clips. If one latch does not click into place, the reel can jump out and injure a person when starting the tool
• Do not wind up the line for the trimmer with a strong retraction, as well as in an amount greater than you can put it in place. It is better not to wind up the rig, than more of it, as this will lead to negative consequences in the form of inability to uncoil it if necessary
• If you own the tool not with two line outputs, but with one (usually these are low-powered units), then the winding process is performed in a similar sequence as described above, only with the difference in the absence of the middle rim between the extreme bases of the spool
• After replacing the material, you should first check that the tool works properly and then start mowing. If it is not checked beforehand, the scaffolding can unravel and injure people

This is interesting!Choose the correct material, in order to avoid injuries when working with petrol or lawn mowers, trimmers and brushcutters. During grass mowing small stones and other materials fall under the rotating parts, which can fly long distances so, despite the fact that the line for trimmer is not a knife, work with the tool should be carried out in protective special outfit. The result of the work done is the following. after the replacement of the new material, the normal material is enough for an area of up to 600 square meters, but taking into account the presence of a reinforcing layer on the line. Conventional nylon materials do not last as long, which is important to consider when working. Do not try to mow thick-stemmed grass with a fishing line, as special metal discs or knives are available for this purpose.