How to cut window plastic corners correctly. How to glue a plastic corner

What is the best way to cut plastic corners

The choice of the method of attaching the corners to protect the walls of the walls is located depending on the material of the corner, on which surface they will be strengthened. In most cases, glue is used. At the same time in the favorites “liquid nails”. This is a universal composition, but before buying, check that a certain brand can glue the materials you need for you.

You can plant a corner on glue if it is even, without huge flaws. If there are pits/hollows, you are unlikely to glue it. In this case, you can use silicone. If you glue snow.white corners, silicone can be taken snow.white. It is better to take transparent to color. No better to use acidic. Although it is cheaper, it can destroy metals or paint.

In both cases, the wall and the corner should be unsuccessful, dry. The composition is applied to the corner, it is pressed to the corner, fixed with stripes of painting tape. We grab it after 40-60 cm. If everything is smooth, it is possible after 60 cm, if you need to repeat the form, after 40 cm or even more often.

Leave in this state until the glue is dry or the silicone does not harden. A clear time see the packaging. Then the painting tape can be removed. It differs from ordinary adhesive tape in that even from cardboard wallpaper it is peeled off without damage to the surface. But to be confident, try to stick and peel off in an inconspicuous place.

A corner of foamed rubber-M-shaped and universal on a self-adhesive base

There is one more option for how to stick corners on a wall with wallpaper, painting. You can use double.sided tape. Stick it first to the corner, then, taking off the protective coating, crush it to the corner. There are corners to which the adhesive tape is already glued. Certain types of foamed rubber or plastic (usually flexible or universal).

Installation on window and door slopes

Even a novice builder will be able to install plastic corners on slopes of windows or doors. Before you glue the corners on the slopes, make sure of the high.quality surface finish. It should be smooth, without bugs. To do this, attach an even ruler, bar or level to the slope. If the slope surface is curved, and it is not possible to fix it, then buy flexible corners.

In all cases, installation technology is the same:

• Measure the height of the side slopes, cut the blanks with a margin for the upper part of the door, opening or window;
• Install them on glue, wait until it grabs;
• measure the width of the opening, cut the required length with a margin on the side of the conjugation with the side strips;
• Cut the front bar at an angle of 45 ° degrees on both sides;
• Attach the corner and make the mark on the side slopes on the side slopes for cutting;
• Cut off the excess on the lateral strips, in place. Attach a metal line to the glued corner and cut off. Do not cut off the extra pieces without a ruler. If the knife slides ugly risk, you will not close anything. You have to start again, and throw away the spoiled piece.
• Glue the upper bar with the adhesive side to the corner, fix it with tape.
• Make sure that the glue drops do not remain on the wallpaper or plastic slopes.

For cases when the walls are trimmed with wallpaper with high relief, you will have to cut off strips of wallpaper.

Good tips can be extended from

• make markings as accurately as possible so that there are no gaps between the joints. Try not to close the joints with silicone. Over time, it will darken and will stand out with an ugly strip against the background of a slope;
• If the processed corners in the niches or openings have an angle larger or less than 90 ° degrees, take measurements in the place, putting the risks with a knife and only then cut off;
• If you are afraid to glue the PVC corners at once, so as not to make a mistake, fix the pieces with tape and make measurements like this;
• so that the gaps are minimal cut off the necessary pieces 0.5-1 mm more. They will fall into place due to elasticity. In such cases, the gaps will almost be visible;
• Before gluing plastic corners on slopes or PVC panels, clean them of dust.

The wide color scheme of the corners allows the designer to give completeness and accuracy to the walls and slopes in the apartment. The use of plastic corners on the slopes of windows, doors, niches and openings will save you from a number of problems for many years.

Field of use and additional information

A corner for framing is made by hot flexion of the PVC of the sheet. Decorative element makes it possible to choose colors that are suitable for any interior. Application area:

• Window slope inside the house or apartment.
• As an external material for protecting external or internal angles.
• Door or arched opening.
• To protect the angle of wall when decorating with wallpaper.
• Corner protection when finishing with plastic in the bathroom.
• Draping of the joint when decorating external cladding with siding.

A plastic element is a good protector from mechanical exposure, but, like any material, it has advantages and disadvantages:

• The installed corner is used as a finish of the seam at the adjustment site of the finishing materials.
• Long service life. up to 25 years.
• Installation is performed independently, you can stick a corner without preliminary preparation.
• The plastic element is easy to cut, produced by multi.colored.
• Acceptable price.

Why do you need plastic corners on slopes among the shortcomings that turned out to be significant:

• Plastic fragile material, so it is necessary to cut it with special tools. it is possible to manifest cracks.
• The combustible finishing element does not tolerate high temperatures.

Peculiarities

To give the inner corners of the window and doorways the desired and neat shape, special plastic corners are installed for slopes. This finishing material is part of the decoration and is needed to hide the corner gaps that arise when using materials of different textures. The corners are collected at the final stage of repair and completely modify the decoration of windows and doors. They not only bring an elegant note to the general atmosphere of the house, but also create a protective function.

Corner parts for slopes are made by hot flexion of PVC sheets using a special technology, due to which they become strong and durable.

They are used for various work on decorating the house and are necessary for:

• cladding of window and door slopes, arched openings inside the apartment;
• protection of the corner panels of the wall during plaster or pasting with wallpaper;
• When laying tiles.

PVC corners have many advantages:

• They can close the gaps of any materials at an angle of 90 degrees;
• can be in use for a long time (service life. up to 25 years) and at the same time do not lose their basic properties;
• easy installation using glue, which can be performed on its own, subject to the correct calculation of cutting;
• the material is plastic, convenient when cutting;
• relatively low cost;
• insignificant mass that does not load slopes;
• do not require additional painting and processing;
• protect the corners from wallpaper wear;
• are not amenable to the influence of ultraviolet radiation, so they do not fade and can be used for a long time;
• Thanks to a huge number of colors and shapes, they perfectly correspond to any interior and add integrity to the entire design of the room.

The disadvantages include some fragility of the material, so you need to cut it carefully and special tools. Also, the corners do not tolerate high temperatures and when igniting, they release toxic gas, which negatively affects the state of human health.

Manufacturers offer various types of plastic corners from PVC in accordance with the size and sphere of application.

• Standard, or P-profile. It is used to strengthen window and door slopes, and it is recommended to install at the initial stage of installation of slopes. The purpose of this profile is the decoration and protection of external angles from deformation. It also helps to hide the gaps between the coatings that are not connected very tightly.
• Versatile, or L-profile. It is used when installing on curly or arched openings. This profile is a flexible angle, the shelves of which converge in a corner of 90 degrees. Very convenient for mounting, because when bending, it preserves the right position for installation well.

• F-shaped. It can be attached to the end sides of the panels even without glue without much effort, since it has a special jumper. Unlike other types, such a profile can be easily removed during wall painting or wallpapering. The main goal of this detail is to hide the gaps between the wall panels, as well as the decor of the openings. In addition, he acts as a platband, which frames the door or window around the perimeter.
• T-profile. It is used if you need to achieve the perfect joint boundary between the slope and panels. It flawlessly connects various materials of the finish that have a different.type texture, and is easily fixed on any surface. When laying a tile, hides uneven tiles on joints with a flat floor base.
• Removable. This type of corner part has a latch and has increased plasticity. It can be easily bent by 3-6 mm. During the repair, it is not necessary to remove them. you just need to fill the wallpaper with a spatula for corners. This allows the assembly much faster.

There is also a self.adhesive version of the PVC corners on sale, which is universality, since it does not need to separately buy glue. In addition, it has good flexibility, which provides an extremely simple installation. For the convenience of the user, they are often sold in rolls up to 50 meters long, and you can purchase a part of any necessary length to avoid joints.

In repair work, plastic surveyed corners are also used. Their purpose is to strengthen and protect the internal and external angles from damage and cracks. Often this type of material is used to give greater strength to protruding joints and leveling the surface.

By type of finishing processes, internal and external PVC corners are distinguished. In turn, the outer angle can be 90 or 105 degrees. The angle of 90 degrees is attached so that only one side of the edging is visible, and the angle with a turn of 105 degrees is mounted by both shelves upstairs.

In their structure, products are divided into a hard design and a soft or flexible, folding profile. The hard design is a classic rectangular profile, both shelves of which are formed in one whole. Such products are used in the design of angles, where you need to bend 90 degrees.

To embody the final image of the interior, white or color decorating details are used, which are suitable for the overall design of the room.

All parts are made according to the standards of building codes and rules (SNiP).

How to fix plastic corners?

First, we note that before the direct installation of plastic corners on the windows, it is necessary to paste out the pores with wallpaper, paint, etc. That is, you can start fastening only after the end of all work on the decoration.

For the installation of a plastic corner, you will need the following tools:

• Installation glue (liquid nails)
• Main tape (adhesive tape), and in a room with high humidity. a sealant of silicone
• scissors for metal, or hacksaw
• pencil
• directly corners from PVC

Window decoration with plastic corners consists of several stages. Consider each of them:

Depending on the place of use, the plastic corners can be equal, with L or F. a figurative cross section, unequal, profiles of the figurative shape. Corner l.figurative profile is most often used compared to other. This is mainly a disguise of cracks in the places of docking materials, edging of sheet materials, angular joint connection.

As a rule, the angle between the regiments of the corner is 90 degrees, and they have dimensions: 1010, 1515, 2020, 2525, 3030, 4040, 5050 millimeters. Such corners are most often used to decorate window and door slopes. If the corner is installed in a place with a significant effect of surrounding factors, then it is better to use corners with dimensions from 20 mm. and higher. Smaller and 1515 corners are usually used to decorate indoors, they organically pour into the overall design.

Plastic corners with an inconspicuous cross section are used to finish arches. The dimensions of such corners are 517, 1020, 1525 mm. A corner with this cross section is easier to fasten, they are quite flexible and easily retain the necessary position, creates a smooth fishing line for a trimmer of bending and an even edge. On one side of such corners there is a cross section that allows you to make a fishing line for a trim of the bend of the required degree.

PVC corners differ, depending on the type of finishing work. So they can be external and internal. External corners have an angle of 90 and 105 degrees. When using a corner, with an angle of 90 degrees, for the window, one bar remains in sight, the other is inserted into the gap of the window frame. A corner with a angle of a turn of 105 degrees is mounted by two shelves outward.

Self.adhesive plastic corners are of particular popularity. They are quite universal, t.to. no need to purchase glue. They also have an increased ability to flexion and extension, providing the ease of installation and the perfect look. Another feature: such corners are sold in rolls, the length in the roll is 50 meters. This allows you to purchase the necessary length and avoid joints.

Plastic corners for slopes: step.by.step installation instructions

Plastic corners for slopes are the logical completion of the repair in the house. They act as a protective and aesthetic design of doorways, window slopes and angles. Today we will consider how to glue plastic corners on slopes with your own hands and the better to glue plastic corners on door slopes.

Field of use and additional information

A corner for framing is made by hot flexion of the PVC of the sheet. Decorative element makes it possible to choose colors that are suitable for any interior. Application area:

• Window slope inside the house or apartment.
• As an external material for protecting external or internal angles.
• Door or arched opening.
• To protect the angle of wall when decorating with wallpaper.
• Corner protection when finishing with plastic in the bathroom.
• Draping of the joint when decorating external cladding with siding.

A plastic element is a good protector from mechanical exposure, but, like any material, it has advantages and disadvantages:

• The installed corner is used as a finish of the seam at the adjustment site of the finishing materials.
• Long service life. up to 25 years.
• Installation is performed independently, you can stick a corner without preliminary preparation.
• The plastic element is easy to cut, produced by multi.colored.
• Acceptable price.

Why do you need plastic corners on slopes among the shortcomings, the following turned out to be significant:

• Plastic fragile material, so it is necessary to cut it with special tools. it is possible to manifest cracks.
• The combustible finishing element does not tolerate high temperatures.

Compare types and sizes

The frame always begins with the choice of the type and size of the plastic element. The table indicates data on plastic corners their dimensions and types for slopes:

During installation, it is required to cut the corner to form the desired length. A sharp clerical knife will help this. If cut it, it is necessary at a clear angle to prepare a knock and a hacksaw for metal.

Important! The plastic corner for internal slopes of color is produced 2.6 m long, 2.7 m, 2.8 m, 3.0 m.

Preparatory work

The mounting process begins with the choice of adhesive mixture. Polyurethane glue well fixes plastic elements, allows you to frame the surfaces where there will be a load. Makes it possible to glue the details in the bathroom if ceramic tiles are glued.

Silicone sealant is used as a latch with a lower load. A corner can be glued with liquid nails, if the edging of a dark color, then you can glue with the help of black composition, for light and white. transparent.

Installation of plastic corners

Work on the installation of plastic corners on slopes is as follows:

• Regardless of where you need to glue the plastic corners. on the door, if there is no platband or window, outside or inside, you need to measure the material and correctly cut off the material along the length.
• Prepare the surface where gluing will occur. remove excess elements, clean the base.
• Install and properly glue strips.

How to properly glue plastic corners on any slopes:

• Well degrease the surface before fixing the corner part.
• Installation foam is not used in the process of design.
• Excess prototrying is cleaned to tangible smoothness.

How to glue plastic corners correctly

• The sticker provides marking with a pencil.
• Before you glue all the details, you should use advice: it is better to measure the corners for slopes of doors and plastic windows in the place. First of all, install the upper horizontal element, and then using the cutting tool, mark the vertical stripes.

Important! Using photos and videos, each beginner will cope with the process of gluing on his own. The metal element is also fixed using screws.

Corps with the help of corners also implies additional fastening of strips using a narrow masking tape. Fix them a strip in several places and leave it for about 24 hours. This time is enough to reliably glue the corners with the surface.

If the corner is used as a finish, then its gluing place should be cleaned from finishing materials. Thus, the quality of the clutch increases. When fixed on the area decorated with trellows, cut a strip a couple of millimeters less than plastic corners. Adhering to simple design rules, to fix decorative elements will be simple and fast, and ultimately they will delight you with aesthetic and laid.back look.

Methods of cutting

The process of shape formation of angles may vary significantly. Each method has its own distinctive features that must be taken into account when performing work. Having decided to take advantage of a certain way, it is worthwhile to figure out how the excess material is cut off in each case.

We use a stencil

The method is relevant when decorating a floor surface in rooms with non.standard configuration. In this case, other methods become an inappropriate option. With their help, it is quite difficult to give the edge of the cut the right direction. You have to constantly adjust the configuration of the plinth, while it is possible to get the required form.

Avoid errors in the formation of the surface allows the manufacture of a stencil, which quite accurately repeats the configuration of a non.standard wall. It is made of thin cardboard or fairly dense paper. Its thickness should fully correspond to the thickness of the floor plinth.

The work is performed in the following sequence:

• prepare material for suitable thickness and length. He must have sufficient rigidity, so as not to deform during the work process;
• Apply cardboard as tightly as possible to the wall. The final result largely depends on this stage. If the stencil is not of high quality, you will have to adjust each element in place, which will significantly increase the duration of the work performed;
• Using the clerical knife, the amount of material is excessively removed, achieving the full compliance of the cut line and the configuration of the wall. Instead of a clerical knife, you can use an electrician. However, in this case, it is necessary to have sufficient qualifications for high.quality work. Otherwise it will not be possible to accurately repeat the required configuration. The fishing line for the cutting of the cut should be perpendicular to the line of conjugation of the wall surfaces;
• control the quality of the manufactured template;
• Cut the mating fragments of skirting boards according to the prepared template;
• Check the quality of the work performed;
• Perform the installation of skirting boards.

We use a knock

Fetling is an indispensable device widely used in the performance of various types of finishing work. The performance of the product allows you to cut off the fragment at the right angle. The P-shaped device has special slots that are used as guides when cutting fragments into size.

To cut off the section of the skirting board of the desired length, the product is laid inside the wort, pressing the wrong side. When laying the front side forward, there is a risk of damage in the process of cutting the product. The edge of the panel in this case is located so that the edge of the panel remains inside the diagonal slot.

Attention! If the sizes of the wort exceed the geometric parameters of the skirting board, it is worth making sure that the product is evenly pressed against the groove side of the device. Only after that it will be possible to cut off the baseboard in size

We use a pencil and ruler

Not everyone has a special tool. Free funds are required to purchase it. Not everyone is able to make a template qualitatively. Even a slight deviation from the required parameters will significantly worsen the final result. In this case, you can use a leaf, pencil, ruler.

The work is performed in the following sequence:

• measurements are performed on the surface of the wall;
• The obtained values ​​are transferred to a plastic skirting board, on which a fishing line is formed with a pencil for the trimmer of the future cut;
• an excessive amount is cut off by the chosen tool.

Attention! With a complex configuration of the floor surface, it will be necessary to measure the corners of the room with particular thoroughness, repeatedly redesigning the obtained values. This will avoid error

We drive in the place

Not always thorough preparation and measurement of the geometric parameters of the walls ensures the accurate cut line. In this case, you have to adjust the baseboard in the place, removing the excessive amount of material. Cutting the baseboard “in place”, it is worth installing it as tightly as possible to the wall surface, mating with floor. Directly on the product, we mark the fishing line for the trimmer, according to which the excessive amount of material should be cut off. During cutting, the cutting tool is located in this way, the slope of the cutting tool was 45 degrees relative to the center of the corner of the profile.

Preparation of plastic corners

After that, the corners are considered ready for installation, and we can begin this process.

Various types of products

There are different types of corners that are divided in size and scope of application. The following varieties are distinguished:

• Standard. They differ in the same size of the sides. Used to give strength to the slopes. Two main sizes are distinguished: 22 and 55 cm.
• Non.standard. Their sides are asymmetric. Used for work with slopes that are installed on curved or arched openings. Most often, size is found: 1020 mm.
• F or t. figurative. Hide spaces that are formed when connecting slopes and wall material.
• On the latch. Differ in a removable design, which allows you to carry out work much faster.

Types of plastic corners

Forms and sizes

The finished corners have, as a rule, an angle of 90 °. The angle itself is not always sharp, there are options with rounded. In appearance, corners to protect the angles of the walls are divided into:

Questions can only be on universal. These are two stripes of plastic or wood.fiber slab connected by a thin strip of flexible material of the same color. Thanks to this connection, you can decorate a dull or sharp angle, internal or external. without any difference. But in terms of reliability of protection, it is inferior to the tough-after all, the flexible part is quite thin.

It is also worth knowing that the corners can be with the shelves of the same and different widths. often found with the same, but it is quite possible to find those who have one wider, the other already.

The width of the shelf for different manufacturers differs. Plastic, for example, can have shelves from 10 mm to 50 mm. The corners of the wood.fiber plate are minimally made with a width of a shelf of 20 mm, metal. from 10 mm, but the maximum length of the shelf is 90 mm (aluminum). So choose from what.

Necessary tool

Here is a list of tools for cutting and installing corners of plastic:

• Installation glue. It has a different name for liquid nails;
• Silicone sealant. Used in rooms with high humidity;
• Hacksaw, pencil, suitable for cutting and scissors for metal;
• The tape is painted if there is no other tape.

Installation of plastic corners

Work on the installation of plastic corners on slopes is as follows:

• Regardless of where you need to glue the plastic corners. on the door, if there is no platband or window, outside or inside, you need to measure the material and correctly cut off the material along the length.
• Prepare the surface where gluing will occur. remove excess elements, clean the base.
• Install and properly glue strips.

How to properly glue plastic corners on any slopes:

• Well degrease the surface before fixing the corner part.
• Installation foam is not used in the process of design.
• Excess prototrying is cleaned to tangible smoothness.

How to glue plastic corners correctly

• The sticker provides marking with a pencil.
• Before you glue all the details, you should use advice: it is better to measure the corners for slopes of doors and plastic windows in the place. First of all, install the upper horizontal element, and then using the cutting tool, mark the vertical stripes.

Important! Using photos and videos, each beginner will cope with the process of gluing on his own. The metal element is also fixed using screws.

Corps with the help of corners also implies additional fastening of strips using a narrow masking tape. Fix them a strip in several places and leave it for about 24 hours. This time is enough to reliably glue the corners with the surface.

If the corner is used as a finish, then its gluing place should be cleaned from finishing materials. Thus, the quality of the clutch increases. When fixed on the area decorated with trellows, cut a strip a couple of millimeters less than plastic corners. Adhering to simple design rules, to fix decorative elements will be simple and fast, and ultimately they will delight you with aesthetic and laid.back look.

Installation of a decorative PVC corner with your own hands

Plastic (PVC) corners are very widely used in the decoration of the premises, they are installed on slopes of plastic windows, they framed the external walls of the walls and slopes of doorways. In this article, we will consider in detail the process of installing a PVC corner on the slope of the plastic window, and also consider how to make a neat joint between two corners.

Step 1. We make markings. We need to attach a PVC-angle to the slope and make a label along the edge of a vertical slope:

The minimum length of the applied corner (L) should be greater than the height of the slope (A), on the width of the corner (b) taking into account the small reserve (C):

For example, if the height of the slope is a = 1500 mm, and the width of the corner b = 30 mm, then the length of the corner should be at least a b c = 1500 30 15 = 1545 mm.

Step 2. We make a neckline on a PVC-apple, removing one line, as shown in the photo below:

The corner was perfect, you can proceed to the next step.

Step 3. The plastic corner is glued only to the slope, this is enough for fixation, so we apply glue to only one of the faces.

As a glue, you can use the “Moment of the Installation”, “Quelyd Masterx” and their analogues. It is not recommended to use super-clock, since it will be almost impossible to fix errors.

The glue on the inner surface of the corner is applied pointily or a thin strip:

We fix the PVC corner using painting tape (for the duration of the glue):

Step 4. We repeat the step 1-3 for the right slope:

Step 5. We mount a corner on a horizontal slope. The length of the corner is taken with the same margin as for the vertical, but taking into account two sides. Marking is also performed, and then cuts are made and the corner is glued to the slope:

Step 6. We mark the place of the cut. The corners will joke at an angle of 45 °:

Step 7. Gently cut out two corners at once. It is very important that the knife is sharp:

Step 8. We cover the joint between the corners with white acrylic sealant. After the glue dries, remove the masking tape. Installation of the PVC-Uglok is finished.

Tips

There are several recommendations that must be taken into account when choosing and installing plastic corners for slopes.

• It is necessary to buy finishing material only after all measurements are made, when all the sloping parameters are clear. A hard profile is suitable for 90 degrees, and for angles with a large deviation, a flexible folding product should be used. In addition, the choice of the correct length of the profile will save effectively when acquiring it.
• Decorative material should be chosen after mounting a window or door, when it is known in what condition the openings. So easier to choose the type of profile.
• It is necessary to take into account what type of room the decor is needed. If a plastic product with increased wear resistance is required, it is more practical to mount a wide angular part, which is particularly durable. And small corners perfectly harmonize with the inner interior of the room.
• If the flexible angle does not keep the form attached to it, it is better to refuse the purchase.
• Plastic corners are quite delicate material, therefore, to avoid cracks during cuts, it is advisable to use scissors or a hacksaw for metal.

• When the assembly of coal slopes occurs in an apartment with an already held repair, for the effect of more fixation it is necessary to clean a narrow strip around the entire perimeter of the decorated opening from any coating.
• For gluing the corner part on the plastic surface, it is better to take a means of “second” glue gel. On a surface covered with plaster or drywall, it is preferable to use “liquid nails”.
• Work on mounting decorative corners is carried out only after the completion of all finishing processes.
• During installation, it is important to observe the correctness of the docking of the material in order to avoid extra work with the gaps.
• When acquiring the material, it is worth making sure that the profiles are absolutely even, with symmetrical sides and without deformation.

If you do not comply with all the rules for ensuring stability during the installation of plastic corners, their practical and aesthetic function is lost.

Preparatory work

Before starting the installation of plastic corners, you must first think about everything and “prepare the soil”. For work, you need a minimum set of tools that any man should be available, not to mention specialized masters.

It includes the following tools: mounting glue (or liquid nails, as professionals call it), ordinary tape (if a painting tape is at hand, it is better to use it), a special silicone sealant (for rooms where air humidity is increased), a hacksaw or scissors for metal and pencil.

Naturally, the choice of plastic corners is an important and responsible task, which will require a more detailed study. Be sure to consult with specialists about this issue. Before going to the store, measure the necessary volumes of corners. Better to take material with a margin. Now we will dwell on each of the three stages in the process of installing plastic corners on slopes.

Complete replacement

If the plastic window sill is not restored, then you can solve the problem radically. the dismantling of the old and the installation of the new.

• You need to get rid of the mounting foam and smoothly pull the plate;
• remove garbage in the place of an old windowsill;
• A new plate using supporting racks is installed in place;
• The joint with the window is lubricated with sealant;
• The void is filled with mounting foam;
• After complete drying, it is necessary to remove the protective film.

This method is resource.consuming and financially non.electrical. But it is possible that this is the only option to make the repair of the window sill of the plastic window.

In order for the windowsill to serve for many years, it is necessary to properly care for it and appropriately operate. And it is worth noting that the repair of the window sill of the plastic window can be carried out with your own hands.

Restoration carried out in time will help to avoid complete replacement. In the absence of suitable tools and free time, such work can be entrusted to specialists.

Ways to solve the problem

We will break the options for restoration of PVC window sills by categories depending on the use of the material used.

Important! Before repairing a plastic windowsill with your own hands, the surface must be cleaned of dirt, degreased with alcohol and dried.

Chemical cleaners

It is known that the plastic surfaces of windows and window sills are covered with an invisible or decorative film that performs a protective function. With inaccurate circulation, scuffs and yellowing are formed on it. To eliminate such minor defects, you can completely restore the part by using the wax for the laminate or the special cosmofen.based cureator.

Small spots and scuffs can be removed with a special cosmofen cleaner

If the window sill is completely yellowed, it is better to apply the composition to its entire surface. It will dissolve the upper yellowing layer and plastic will become like a brand new. The restoration of the windowsill will be completed on this.

Special putty

The use of a specialized mixture of the Fenoplast or Reparaturset type to close up small defects today is a very popular way. In stores, it is sold in the form of powder complete with a spatula and a measured glass. Preparing a putty according to the instructions will not be difficult. After application, such a mixture acquires properties close to PVC and easily smear the cracks, whether it is a crack or scratch. Experienced specialists use not water to breed a two.component mixture, but a primer for a deeper penetration, which helps to obtain a sufficiently strong coating.

With the help of putty, you can close small scratches and cracks

Immediately after the preparation of the composition, it follows:

• Put a putty to the surface.
• Close the scratch and align.
• Wait 10-15 minutes. Until complete drying.
• Pull out with sandpaper.
• Poop the Fenosol S5 “UVA”.

To understand what the repair of a plastic windowsill with your own hands will look like with a putty, you need to start with more inconspicuous places.

Liquid plastic

If you do not know how to remove scratches from a plastic windowsill, use liquid plastic. This material is completely indispensable when shallowing deep scratches and large dents. It allows you to restore even the most advanced deformation.

To correct deep defects of the window sill, liquid plastic is used

Already a ready.made composition of the Cosmofen Plus type, all the recesses on the plastic windowsill are laid down until a flat surface is obtained. After that, you need to see how the chatted cracks and the patch will differ from the overall texture of the plate. Therefore, additionally it can be glued with a self.adhesive decorative film.

Laminated film

This is a fairly simple and affordable option for restoring the surface of plastic windows with numerous defects. A wide variety of colors and the choice of the assortment for simulating a variety of texture (wood, stone, Russian pattern, etc.D.) make this product very popular even when the restoration of a plastic window sill is not required.