How To Make A Hole In A Tree Without A Drill

Tips for drilling metal, wood, concrete

When drilling holes in a metal with a hand drill, the drill is usually jammed. To fix this defect, a wooden cork, previously hammered into the hole, will help.

Drilling a hole in a thin metal sheet will not be difficult if you clamp it in a vice with a wooden block. The most inconvenient thing is to drill thin metal sheets. They continually strive to break out and injure the drill driver.

Cut yourself a “shovel” from steel with a convenient handle. Fasten the workpiece with clamps to the upper surface of the “shovel”.

Those who have tried know that a large-diameter drill will “break” the hole, and it will be uneven. Place a piece of rubber or a rag folded in several layers under the drill and start working. The hole will be flat.

To cut blind holes in the part, you can use a piece of a round file clamped in an electric drill chuck. In order not to damage the back wall of the part, the working end of the file fragment should be slightly rounded on an emery wheel.

Drilling a radial hole in a metal bar or tube is very difficult. Especially if you are trying to do it with a hand drill. This task can be facilitated in this way: in a wooden block, drill a hole of the corresponding diameter, insert a pipe there and calmly drill, without fear that the drill will slip.

If the blind (non-through) hole in the metal part is filled with paraffin, then the thread cut on it will be clean.

Drilling a large hole in the board at home is very difficult, because the shank of a large drill cannot be clamped in the chuck of a hand drill. A hole with a diameter of 15 to 40 mm can be made using a simple device consisting of a metal rod and a hacksaw of the right size piece of cloth. Its cutting edges are sharpened at an angle of 45 degrees, inserted into a longitudinal slot previously made in the shaft, and soldered or fixed with a wedge that is driven into the slot.

A person experienced in experience will never begin to drill a round log before reliably fixing it. He knows that, without taking precautions, most likely he will not be able to drill a hole exactly along the intended path, and besides, he might lose the drill.

Place a spring of 1.5-2 cm long between the handle and the “slider” in the wood hand drill, and even with sudden movements of the “slider”, a finger that accidentally is between it and the handle will not pinch.

When drilling large diameter holes (20-30 mm) in a tree, the required drill or perk may not be available. In this case, first drill a hole of a smaller diameter, and then insert a flat steel washer (preferably a new one) into the rotary chuck and pass the hole again. This method is also applicable for countersinking holes.

If you need to drill a lot of holes in wooden parts at right angles, then take a cube of solid wood, drill a reference hole in it with great accuracy. And then use this conductor to work like this. A cube put on the drill will serve at the same time as a limiter of the drilling depth.

Corking capsules from lemonade or beer is a good substitute for a drill, when it is necessary to drill compass needles in the wood holder, then reduce the risk of breaking it when the fiber material or plaster has a hole with a diameter of about 20 mm. Pierce the plug, put on the bolt, securing with two locknuts, and drill.

READ  How to Make a Grass Trimmer

It is difficult to make a hole in layered plywood, it splits. Take the steel tube of the desired diameter, grind the cutting edge inside with a round file and cut the teeth with a trihedral file. Insert a wooden cylinder with a nail without a hat inside the tube. During operation, the end of the nail, protruding 1-2 mm, is the guide.

So that when drilling small parts from sheet material they do not scroll, we recommend that sandpaper be placed under them.

If you fix a drill with a diameter of 0.8-1.1 mm, you will drill holes of small diameter in a tree, textolite, and plastic.

There are many devices for cutting holes of large diameter in sheet material. plastic, plywood, chipboard, etc. You can use the design: a bracket bends from a strip of steel with a thickness of 2-3 mm, its ends are screwed in, and a hole is drilled in the center, then the bracket is put on a bolt with a sawed-off head. For operation, the device is clamped in the chuck of an electric drill.

Cutting a large hole in the sheet material can be done in a simple way: clamp a nail (it will serve as an axis) and a piece of drill (it will be a cutter) in a vice. The circumference is cut through the rotation of the sheet around the axis.

A circle of any diameter from plywood can be cut precisely, accurately and quickly with a wooden plank and two pointed nails driven into the plank.

The pencil sharpener cutter (sold separately) can be used with success for boring holes in wood and plastic. It is fixed in an electric drill cartridge and the edges of the hole are machined.

A potato peeler in the hands of a craftsman is an almost ready tool for processing rounded holes in plywood. You just need to sharpen its cutting edge.

When drilling a board or plywood, remove burrs at the same time, for which string several rings of dense felt onto the drill.

It is easier and faster to drill concrete with a carbide drill sharpened asymmetrically. However, we still recommend planning and starting holes with a drill with a usual sharpening.

When drilling holes in the ceiling, crumbs of concrete and plaster scatter in all directions, get into the eyes, behind the collar. Make a funnel from a spring wire, cover it with plastic wrap and put it on a drill.

Видео: How To Make A Hole In A Tree Without A Drill

If you drill a concrete or brick wall made in a tin can from under a shoe cream, dust will collect in it, and will not fly into the room.

If you didn’t have a drill for drilling concrete, you can replace it with a punch from the Dream Settlement set. Inserted into the drill chuck, it takes concrete well.

When drilling a hole in concrete or brick, the drill will last longer if it is periodically wetted with water. It is convenient to use an elastic plastic bottle as a water tank.

When drilling holes in the wall, the drill is very difficult to keep in a strictly horizontal position. Attach to her
the case with electrical tape is a small level or a bubble replacing it, and the matter will be greatly simplified.

If you need to drill a through hole in the wall, and the length of the drill is not enough, what should I do? Try this operation in two steps: on one and the other side of the wall. Having drilled a hole at the intended point, put a magnet in it. Then use a compass to find the drilling point on the opposite side of the wall. The compass needle will not be mistaken.

READ  How to Hang a Shelf Without a Drill

how drill concrete a wall with a conventional drill not a hammer drill?

How to drill a concrete wall with a conventional drill? such a question was probably asked by the master when they had to hang shelves, cornices, etc.

Concrete is a strong material, therefore it can be drilled extremely poorly. How to do hole in the wall without a drill. How to drill a concrete wall. Hole in. Even how to drill a wall in a prefabricated house, the task can be thought to be unsolvable.

Although, if you know certain secrets, this common rumor process you greatly simplify.

Choose a tool

What you need, the first question that a home foreman should ask himself is not how to drill a concrete wall with fittings, but with what. The main assistant here will be a puncher, because it is intended for stone not concrete. Despite this, even powerful drills can not cope with a wall with a width of more than twelve cm. How to drill a hole in the metal. Although if we talk about foam concrete, it is preferable to drill, as the punch simply break it.

The quality of the drill also determines whether it will be possible to drill a hole in a concrete wall.

One of the best options is to use drills designed specifically for the impact drill. Their working part is essentially a plate made of strong metal. Using these drills, the question of how to drill a thin concrete wall is resolved.

There are also diamond core drill bits. How to make the right hole, make a hole without a drill and punch. I make holes without a drill and a deep hole in how to make. They are very strong, use them in special drilling rigs, so they do not cost enough. Therefore, they solve the problem of how to drill a hole in a concrete wall at home, it is impractical no less.

Crown application

Often you need to get a large diameter hole in the wall for a wall outlet. How to drill a bearing wall and then? Then the crowns are used, in which there are metal solders around the circumference. Crowns are found in different sizes, but the 68-centimeters, which are designed for sockets at this time, remain the most popular. How to make a hole in the speed of the drill, the third way involves doing without. How to make a hole in glass, a hole in glass without a drill. When working with these parts, the hammer must turn off the shock mode.

There are such crowns and also for drills. How to drill a hole in a tree without a drill. Alas, they have a different type of spraying. from a tungsten carbide alloy. It is convenient to use them, since it is quite possible for her to drill a hole in a concrete wall without drilling a hole in a tile at the same time. Such crowns are used only with powerful drills.

How to make a hole without a do-it-yourself drill at home

Healthy advice remains for our client here :. Pain treatment c.

Boers. an additional device than drill concrete the wall. How to drill a hole in a concrete wall with a puncher. how to drill hole in a brick wall. Their diameter is diverse. Experienced craftsmen advise you to make a selection, starting from the diameter of the dowels.

We drill concrete with a perforator

What is needed, how to drill hole in a concrete slab using a hammer drill? The procedure is simple:

  • the drill switches to shock mode, then drilling begins; the tool must be kept strictly at a right angle;
  • after a couple of weeks, the drill is moistened with water, this will help to avoid overheating;
  • if it is possible to drill a reinforced concrete wall, the drill, without turning off the device itself, needs to be removed;
  • in order to clean the hole obtained from dust, a drill is launched several times there.
READ  How to make a do-it-yourself grinder from an angle grinder

Can’t drill a wall? Has the puncher run into something solid? So, you need to try to make a hole somewhere else.

The content of the article

How To Make A Hole In A Tree Without A Drill

  • How to drill a hole in a tree without a drill
  • How to choose a drill
  • How to drill granite

The easiest way to obtain such holes is to use an awl with a diameter of 1 to 3 mm. It is easy to make an awl from a thick needle or even from cutting a piano wire, whose length is about 5 cm. The needle or wire is first hammered into a piece of hardwood for half the length, a handle is subsequently made from this tree. The end of the wire remaining outside is sharpened by 3 or 4 sides. A well-made awl acts in this case as a drill, piercing the wood, it rotates and it cuts and twists the wood fibers, and does not just push them apart.

DIY drill

Small-sized hand drills are best suited for this operation, the likeness of which can be made independently. To do this, two shoelaces and a handle are attached to the rigid axis, which can be a steel or wooden rod, and a sharpened clove from the bottom. In the middle of the rod you need to fix a heavy flywheel, which will act as an inertial battery. In order to bring this drill into action, the laces are manually screwed onto the rod, and then, having set the carnations in the right place, press the handle. The rod rotates and the stud drills, the pressure on the handle is stopped when the laces are completely untwisted. The flywheel rotates by inertia and winds them again on the rod, and then it stops and you need to press the handle again. Viscous wood species may not succumb to such a drill, as the drill will bind and slow down.

Do-it-yourself screw drill

For the construction of a screw drill, a rotation mechanism from a children’s top is well suited. Instead of a cartridge, a pencil holder for a compass is well suited. When the engine with the same thread is lowered by hand, the screw axis of the drill starts to rotate. The head of the drill with such a mechanism of action must necessarily rotate on the axis freely.

If there is no top at hand, the screw of such an action can be bent independently. To do this, you need a strip of steel, one end of which needs to be fixed in a vise, mounted on a machine or on a table, and the other end to be fixed in a manual vise. When rotating a manual vise, the strip is evenly twisted into a screw, on which a wooden slide with a pre-drilled hole is then mounted. In order to prevent the engine from experiencing difficulties when passing the helical surface of the strip, the strip is heated and, passing in this state along the engine, a thread is made on the strip. To make a hat, a small wooden ball is suitable, in which a hole is made in diameter slightly larger than the diameter of the screw.