How to paint grass properly with a trimmer. Tips (mowing grass)

Glass haircut with a trimmer

In order for the lawn in the garden to look good, it must be correctly watered, fed and trimmed with. Currently, there is a lot of diverse technology that imprisoned grass. Her choice remains behind the owner of the lawn territory, but for small sites it is worth paying attention to the trimmer for the grass.

This device is created in order to cut the lawn exactly.

It is especially convenient to do this such an electric oblique in hard.to.reach places:

Also, the pluses of the trimmer for grass can be called compactness and lightness in use.

After the window, it is easy to clean from the remnants of the grass and check the serviceability, after an inspection of the cutting fishing line. The price of this device is much less than the cost of a lawn mower. The disadvantages of the tool under consideration are the absence of a collection of mowed grass and low power.

Description of a trimmer for grass for haircuts of a lawn

The trimmer for grass is essentially an electric oblique. It looks like a long pole, at one end of which there is a haircut mechanism, and on the other. a handle for holding the tool. The engine can be both in the upper and lower part of the pole. it depends on whether the gasoline trimmer for grass or electric.

These tools for cutting grass are:

The effectiveness of the described device depends on:

The principle of operation of a trimmer for the grass is simple. a drive, gasoline or electric, twists a bobbin into which the fishing line for a trimmer and a reel are mounted. The ends of the fishing line, peering out, straighten and act like blades when rotation. The thickness of the fishing line can change. from 1 mm for constant weekly mowing up to 4 mm for especially overgrown sites.

The electric tool has a number of advantages and disadvantages.

• Its pluses can be called:
• almost silent work;
• Lightness of the tool;
• simplicity in management;
• Consumable material is only a fishing line for a trimmer.
• The disadvantages of such tools are:
• dependence on the length of the cord and the electric socket;
• small power;
• Prohibition of work with wet grass.

Also, during mowing, you have to monitor the cable that can fall under the cutting part of the tool. If the plot is strongly overgrown, then in one call the grass does not cut. You should go through the area several times, removing 10-15 cm.

Battery trimmers for grass are relatives of electrical. They differ in that they do not need to be connected to the network. only the battery should be charged. However, a similar tool can work for 25-30 minutes.

During this time, you can have time to mow a plot of 100 m². Then the device will have to be charged, and this takes from 5 to 10 hours. As an option, you can buy several spare batteries and extend mowing for 1-2 hours.

Gasoline trimmers for grass use expensive fuel today. If the owner has no problems with the purchase of gasoline, then you can opt for this option. It is more powerful and not limited by the battery ability.

Such a tool can be mowed until the fuel ends or the fishing line for the trimmer ends. In addition, similar trimmers for grass working on a mixture of gasoline and oil are much more powerful than electric. A similar unit can be cut off on a section of up to 1000 m².

There are two disadvantages of gasoline braids for grass. a lot of noise and exhaust gases. In addition, if you do not comply with the correct composition of the mixture, the device can be launched with problems. Wheel gasoline trimmers for grass is almost a lawn mower. Two large wheels are mounted on them, which improve controllability and cross.country ability on especially difficult sites.

Kosim the grass

The purpose of the trimmer head (trimmer coils for grass, mowing head, trimmer’s spilles for grass)

• To remove all unwanted vegetation under the walls, along fences, borders, around trees, pillars, bushes, between stumps and other obstacles.
• To mow grass on the lawn in the places inaccessible to the lawn mower.
• In order to selected liquid grass and weeds before the mowing of the site on hay.
• To drain weeds in the garden between plants.
• To drain the board of potatoes in the garden before digging up.
• To completely remove grass and weeds, for example, from paths.
• To sweep (an air vortex is created from large revolutions of the fishing line for grass).

Note

Trimmer head (mowing head or trimmer coil for grass) has high performance when mowing grass, t.to. It is easier for a metal knife and it has more capture diameter. 45 cm, against 25 cm at the hay knife.

Varieties of the tool

Three versions of garden trimmers are available on sale. electric, battery and gasoline. Network models connected to the outlet are less common, since they have minimal capabilities for autonomous work due to binding to the mains. In addition, from the point of view of savings, this is not the best trimmer for grass for mowing grass. An electric unit can justify itself only in work on the sites adjacent to the house, if there is the possibility of eyeliner eyeliners for connecting a cable.

The potential for shaking flying stones puts windows in the houses and cars. The shields around the Trimer head are in place to reduce the amount of flying debris and protect the operator. no one removes the shields, after the modified trimmer for grass is no longer under the guarantee or can be used safely.

When refueling repeatedly, make sure that the engine is stopped, and the trimmer for the grass is installed on a flat flat surface. it is preferable to not herbal. Trimmer for grass should never stay on the grass for a long time. Re.refueling should be performed with the proper system to avoid leakage or overflow.

A direct competitor of electrical models have always been considered gasoline modifications. They provide high power, practically do not limit movement and cope even with sharp shrubs. But, a gasoline trimmer for grass for mowing grass is also characterized by great weight, noise of work, strong vibrations, produced gases and high cost. Battery versions are also not tied to source of energy, but they lose to gasoline trimmers in power indicators.

Be sure to use the appropriate line weight, as indicated in the user manual. A strip of trimmer for grass, which is too thick for the engine, can lead to damage. Some trimmers for grass can take a blade for pruning, but never use a blade on a trimmer that is not intended for the use of rubberized blades. Accessories that are not intended for a specific trimmer for grass can create excessive vibration, engine wear or linking. This can lead to engine voltage, a possible failure of the component and potential damage to the operator.

How to fix a disk or a fishing line for a trimmer on a trimmer

The cutter is attached to the drive. The place of fastening is the gearbox. Disk or video is easily installed. The principle of attaching cutting discs to the trimmer is as follows:

• First fix a figure washer using a hexagonal key.
• Install the disk on the shaft
• Then install the upper washer and fasten it with a clamping nut.
• The nut should be unscrewed using a special end key, which is usually supplied with each tool.
• The nut should be turned counterclockwise.
• During rotation, wedge the shaft with a hexagonal key.

Remove and install the disk on a trimmer for the grass in the reverse order. Read more about how to attach a coil with a fishing line to a chainsaw, read in this material.

Gasoline gas mowing gasoline with butter

Before starting the mowing, a gasoline motorcycle is necessary to season it with gasoline. As fuel, gas and oil are used. However, note that gasoline and oil should be mixed only for two.stroke engines. Four stroke engines operate on clean gasoline because they have a separate tank. Oil Carter. Two.stroke trimmers for grass do not have an oil crankcase, so only gasoline and oil should be poured into the tank.

For gasoline, it is recommended to use the fuel of the AI-92 brand. To make the right choice, refer to the manufacturer’s instructions. Often, most manufacturers recommend using AI-92 fuel, and only some recommend AI-95.

Gasoline should be diluted with malt in a ratio of 1 to 25. This means that to 1 liter of gasoline you need to add 40 ml of oil for two.stroke engines. However, here not everything is so simple. Ratio 1 to 25 is universal, but for each tool model there are values. These values ​​are also indicated by the manufacturer in the instructions. You can find more detailed information about the correct dilution of gasoline and oil in a gasoline chainsaw here. Having diluted oil and gasoline, completely fill the tank and let the car start the work.

It is interesting! If this is a four.stroke chainsaw, it is necessary to pour pure gasoline into the tank and add the engine oil to the maximum level.

Gasoline gas mowing gasoline with butter

Before mowing grass with a benzo.leggos, it is necessary to season the tool with fuel. As fuel, gasoline with butter is used. However, take into account that mixing gasoline with oil is needed only for two.stroke engines. Four.stroke engines operate on pure gasoline, since their design has a separate container. oil crankcase. There are no 2-stroke gas crankcases in the design of the 2-stroke gasolimers, so you need to pour exclusively gasoline with oil into the tank.

As gasoline, it is recommended to use AI-92 brand fuel. In order not to make a mistake in choosing, you need to read the instructions offered by the manufacturer. Often, most manufacturers recommend using the AI-92 brand fuel, and only some recommend filling AI-95.

Gasoline must be diluted with a small one in a proportion of 1 to 25. This means that 40 ml of two.stroke oil must be added per 1 liter of gasoline. However, not everything is so unambiguous here. The proportion 1 to 25 is universal, but each tool model has its own values. These values ​​are also indicated by the manufacturer in the instructions. details about how to properly dilute gasoline with butter into a lawn mower is described here. After breeding gasoline with butter, pour a full tank, and start work.

It is interesting! If a four.stroke lawn mower is refuel, then pure gasoline must be poured into the tank, and engine oil is added to the oil container to the maximum level.

Instructions on how to use a gasoline trimmer learning to start a tool

Before working as a tool, it must be initially started. How to get a lawn mower, consider in detail. First, the tool should be placed on a flat surface so that the disk fixed to the shaft does not cling to anything. After that, we proceed to the launch of the engine of the lawn mower:

• Initially, fuel should be swollen into the launch system. To do this, press 4-5 times on a primer (soft hemisphere on a carburetor)
• Next, transfer the carburetor switch to the “OFF” mode. This switch is responsible for opening and closing the air damper. The transfer of the switch to the “OFF” mode allows you to make the fuel mixture during the launch of the enriched
• There is a switch on the handle near the accelerator. He is responsible for turning on and disconnecting the ignition. Before starting, you need to transfer the ignition switch to the “1” mode
• Now you can launch. To do this, you need to hold the tool with one hand, and the second sharply pull the starter handle. If the engine braid engine did not start the first time, then do not despair. Attempts to start the start until the engine starts. Typically, for this, 2-3 repetitions should be performed
• If the engine does not start after 5 repetitions, then the fuel suction should be repeated using a primer, and start starting again
• As soon as the motor starts, you need to transfer the air damper switch to the “ON” mode. This means that a mixture of fuel with air enters the cylinder
• Let the tool work for 15-30 seconds at idle while the engine warms up, after which you can proceed to the span of grass

The above instructions for starting the engine and trimmers are appropriate for a cold start. If in the process of operation the tool was a pause, then when re.starting the non.surviving engine to close the throttle, there is no need. It is required to simply turn on the ignition, and pull the starter handle.

It is interesting! If the lawn mower is new, then do not forget that it is impossible to work at full power until the running.in procedure passes. This is important to consider, otherwise the engine details will quickly be worn out and will fail.

How to mow grass with a trimmer with a metal knife

As the border of the mowing area moves, move the fuel and the bag.

If the grass was setting down: you need to hand the steering wheel forward and mow to the left with an inclination by the handles to the left (sector ~ 11 hours) and the right with the tilt for the handles to the right (sector ~ 1 hour), and do not rush!, to mow the grass cleanly and so as not to “dig” the earth.

During the mowing of grass (and turns), do not forget to look around!:

• To notice the gesticulation of others, drown out the motor and remove the headphones,
• So that closer than 15 m children, animals, spectators and assistants do not come up, t.to. When a metal knife in the grass collided with a motionless object, a trimmer for grass or a lawn mower (motorcycle) can be strongly thrown to the side or expanded back, and a trimmer for the grass rotates at a speed of up to 10,500 rpm. And he is able to cut off his hand or leg.Also, when the grass is mocking the trimmer from under the knife, various objects (crushed stone, glass, garbage) can fly out and ricochet).

How to mow grass with a trimmer (more about the mowing technique)

The engine revolutions when the trimmer mowed depending on the load on the engine. the thicker the grass and, of course, is heavier than the engine, the bolder you need to open the “hole” (throttle in the diffusor of the carburetor).

Work speed of the engine during the mowing of grass with a trimmer try to keep constant (slightly higher than medium). or less gas. only depending on the overall load on the engine. No need to completely discard gas (and immediately acceleration again) with each wave of braids for grass. And the clutch is not for long, and the edges on the drive shaft can “overtake”, and the overall wear of the trimmer for grass (motorcycles) increases sharply.

Before mowing grass, we find out the parameters of the site

(to know which knives to take, how much fuel and time are needed)

• Grass density;
• The hardness of the grass;
• the splendor of the grass;
• wovenness of grass;
• (The height and thickness of the grass are not important)
• the boundaries of the site;
• what irregularities (how to come in);
• the presence of hidden obstacles (remember)
• that not cut (bushes, flowers, seedlings).

To mow grass in the summer is a disaster, and not just homework how to use a trimmer. If your yard or site is strongly overgrown with grass, you can scare you, but this part of the article will help to figure out how to mow grass with a trimmer easier and less irritating.

How to use a trimmer

Tips on how to mow grass

• Mowing grass when it is not very large. This will allow you to cope with work much easier and faster than if you mow a strongly overgrown lawn or yard. A large mass of grass, weeds, plants and trimmer will be hard to grind. In addition, a lot of chopped grass will lie on the surface, which must either be cleaned, or wait until it dries, or while it becomes compost, which is not very beautiful and can cause various diseases of the grass.
• Avoid mowing not grass, but fences, stones, bricks, any other hard objects, as this will greatly accelerate the wear of the fishing line and it will require its more common replacement.
• Some will have to wear an orthopedic corset (although it may seem stupid). Back support allows you to maintain performance longer and feel more comfortable.

Warning how to use a trimmer

Trimmer for grass, like a twin.franc grinder, chainsaw or garden tractor is unreasonable for what it is not intended for.

Keep a trimmer for the grass away from yourself so as not to cut off your fingers or leg.

Do not mow a trimmer in water or wet grass. If you have an electric trimmer for grass, you may hit an electric shock. If you have a gasoline trimmer for grass, you can pollute water and grass with fuel and exhaust gases.

You will need things to mow grass

• Pants. Preferably strong working jeans without holes. You can mow grass somewhere, so if your legs are not protected, soon you will feel how several thousand ants crawl along your legs and bite you. Sometimes a weed can scratch to the blood or stuck strongly, thrown back on the mower.
• Gloves. wandering, leather, it does not matter. If you mowed grass without gloves, then by the end of the kota you will not be able to move even a little finger without pain. The weight of the grass through a trimmer for the grass presses in the hands and abrasions and scuffs will appear on their hands if they were not in protecting gloves.
• Protective glasses. you cannot mow grass with your eyes closed, because small pieces of grass fly in the face. One good hitting your eyes will convince you that protective glasses are mandatory. This applies to one of the main rules how to use a trimmer.
• Have a sufficient amount of drinking water at hand. Even if you think it will not be hot, think again. You need to mow grass with a vibrating trimmer for a long time.
• Have a spare fishing line for a trimmer or a seasoned trimmer head to replace if it ends.
• If you have an electric trimmer for grass, you must have an additional extension cord. If you have a gasoline trimmer for grass, you must have a supply of fuel.
• Rake to rake mowed grass or weeds.
• Headdress if you work in the sun.
• High boots (pants are best tucked into boots).
• If you plan to work at dusk or later, make sure that you have a spray from insects and a lantern.

How to mow grass with a trimmer with a metal knife

As the border of the mowing area moves, move the fuel and the bag.

If the grass was setting down: you need to hand the steering wheel forward and mow to the left with an inclination by the handles to the left (sector ~ 11 hours) and the right with the tilt for the handles to the right (sector ~ 1 hour), and do not rush!, to mow the grass cleanly and so as not to “dig” the earth.

During the mowing of grass (and turns), do not forget to look around!:

• To notice the gesticulation of others, drown out the motor and remove the headphones,
• So that closer than 15 m children, animals, spectators and assistants do not come up, t.to. When a metal knife in the grass collided with a motionless object, a trimmer for grass or a lawn mower (motorcycle) can be strongly thrown to the side or expanded back, and a trimmer for the grass rotates at a speed of up to 10,500 rpm. And he is able to cut off his hand or leg.Also, when the grass is mocking the trimmer from under the knife, various objects (crushed stone, glass, garbage) can fly out and ricochet).

How to mow grass with a trimmer (more about the mowing technique)

The engine revolutions when the trimmer mowed depending on the load on the engine. the thicker the grass and, of course, is heavier than the engine, the bolder you need to open the “hole” (throttle in the diffusor of the carburetor).

Work speed of the engine during the mowing of grass with a trimmer try to keep constant (slightly higher than medium). or less gas. only depending on the overall load on the engine. No need to completely discard gas (and immediately acceleration again) with each wave of braids for grass. And the clutch is not for long, and the edges on the drive shaft can “overtake”, and the overall wear of the trimmer for grass (motorcycles) increases sharply.

Before mowing grass, we find out the parameters of the site

(to know which knives to take, how much fuel and time are needed)

• Grass density;
• The hardness of the grass;
• the splendor of the grass;
• wovenness of grass;
• (The height and thickness of the grass are not important)
• the boundaries of the site;
• what irregularities (how to come in);
• the presence of hidden obstacles (remember)
• that not cut (bushes, flowers, seedlings).

To mow grass in the summer is a disaster, and not just homework how to use a trimmer. If your yard or site is strongly overgrown with grass, you can scare you, but this part of the article will help to figure out how to mow grass with a trimmer easier and less irritating.

How to use a trimmer

Tips on how to mow grass

• Mowing grass when it is not very large. This will allow you to cope with work much easier and faster than if you mow a strongly overgrown lawn or yard. A large mass of grass, weeds, plants and trimmer will be hard to grind. In addition, a lot of chopped grass will lie on the surface, which must either be cleaned, or wait until it dries, or while it becomes compost, which is not very beautiful and can cause various diseases of the grass.
• Avoid mowing not grass, but fences, stones, bricks, any other hard objects, as this will greatly accelerate the wear of the fishing line and it will require its more common replacement.
• Some will have to wear an orthopedic corset (although it may seem stupid). Back support allows you to maintain performance longer and feel more comfortable.

Warning how to use a trimmer

Trimmer for grass, like a twin.franc grinder, chainsaw or garden tractor is unreasonable for what it is not intended for.

Keep a trimmer for the grass away from yourself so as not to cut off your fingers or leg.

Do not mow a trimmer in water or wet grass. If you have an electric trimmer for grass, you may hit an electric shock. If you have a gasoline trimmer for grass, you can pollute water and grass with fuel and exhaust gases.

You will need things to mow grass

• Pants. Preferably strong working jeans without holes. You can mow grass somewhere, so if your legs are not protected, soon you will feel how several thousand ants crawl along your legs and bite you. Sometimes a weed can scratch to the blood or stuck strongly, thrown back on the mower.
• Gloves. wandering, leather, it does not matter. If you mowed grass without gloves, then by the end of the kota you will not be able to move even a little finger without pain. The weight of the grass through a trimmer for the grass presses in the hands and abrasions and scuffs will appear on their hands if they were not in protecting gloves.
• Protective glasses. you cannot mow grass with your eyes closed, because small pieces of grass fly in the face. One good hitting your eyes will convince you that protective glasses are mandatory. This applies to one of the main rules how to use a trimmer.
• Have a sufficient amount of drinking water at hand. Even if you think it will not be hot, think again. You need to mow grass with a vibrating trimmer for a long time.
• Have a spare fishing line for a trimmer or a seasoned trimmer head to replace if it ends.
• If you have an electric trimmer for grass, you must have an additional extension cord. If you have a gasoline trimmer for grass, you must have a supply of fuel.
• Rake to rake mowed grass or weeds.
• Headdress if you work in the sun.
• High boots (pants are best tucked into boots).
• If you plan to work at dusk or later, make sure that you have a spray from insects and a lantern.

Preparation of the electrimmer

If it goes or just ends the rain, you can get a shock when cutting wet grass. Before the first turning on, make sure that you have assembled the device correctly. some models are delivered disassembled. The exact assembly will protect you from injuries, and the unit itself. from failures and sudden breakdowns. Instructions for the assembly of a trimmer for grass are described in the user guide.

When using the electrimmer, charge the battery (if the device provides for autonomous operation). Lubricate a mechanical gearbox using lithol or solidol. If the battery is not in the device diagram. connect the fork to the outlet and join in the work.

Preparation of a benzotrimer for work

Pour gasoline (or diesel) into the tank without overflowing it. Two-stroke trimmer engines require mixing gasoline with engine oil (not automobile) in a ratio of 1: 32-1: 50. You need to know what oil in what proportion is interfered with gasoline precisely for your model. In four.stroke trimmers, you will need to pour oil and gasoline into different tanks. again, according to the instructions.

Check if the cutter is suitable for work (fishing line for trimmer or cord). Before starting work, hang a device on your shoulder. all trimmers for the grass suggest the presence of a belt.

Get the device handle as indicated in the instructions. Some trimmers for grass are equipped with a double handle resembling a bicycle steering wheel. Now follow the following actions:

• Close the air damper;
• Turn on the ignition circuit using a key or button;
• If there is a pumping mini-pump on a carburetor-upload a little fuel to the engine, making 3-5 presses on the “rocking rock” lever;
• Pull the starting cord until a significant resistance appears to its movement;
• Twer the cord sharply up to 5 times.

The engine will start. With a mowing of grass, use protective glasses or a helmet with a grid that protects from the expanse of the grass towards the face.

Protective equipment when working with a motorcycle (trimmer)

Tip: This article does not replace the instructions given in the guide for the use and safety precautions. Always read the product management before use and observe safety precautions.

For safe work with a motorcycle (trimmer) you will need:

• Helmet;
• Headphones;
• Eye protection (mesh shield or glasses, but it is better to use both);
• Long durable pants (the legs are in the immediate vicinity of the knife or fishing line, so they must be protected);
• Shoes with a non.slip sole (preferably with a steel nose);
• Soft gloves (to protect and absorb vibration);

Knives for motorcycles (trimmer for grass)

When working with a motorcycle we can use a fishing line for a trimmer. However, a real advantage (in addition to high engine power) is the ability to equip metal knives.

Various types of knives for trimmers are designed to cut different types of vegetation:

• A knife with 8 or less teeth: grass and weeds;
• A knife with 9-40 teeth: thick weeds and shrubs;
• Knives-saws with more than 40 teeth: small trees and young seedlings;

When replacing a knife, be sure to use gloves.

Each knife indicates the size (diameter) of the landing hole in the center. This is usually 2.5 cm, but cases are different. Therefore, look in the operating manual, what size on your trimmer.

Care after mowing

Immediately after the procedure, it is necessary to remove the mowed grass. They leave it only if it was assumed that it will be used as a mulch that supports the necessary level of humidity in the soil and restraining the growth of weeds. Immediately after mowing, the site needs to be well watered and fertilized. Moisturizations are best done in the evening 3-4 times a week.

For feeding, use liquid organic mixtures or special complexes containing nitrogen. Before winter, phosphorus and potassium-containing mixtures are introduced. The lawn also needs periodic aeration. piercing the soil in order to improve moisture penetration to depth after heavy precipitation and prevent its stagnation on the site.

How often you need to mow the lawn

If you mow grassy plants regularly, then this will provoke the formation of dense turf, which will not give a chance to the active growth of weeds. Weed cultures will simply be replaced by new cultural shoots. Regular haircut also allows you to protect lawn herbs from exhaustion and extend their growing season.

Recommended mowing frequency in the spring. after 4-7 days, in the summer. 7-10 days. How much time should pass between the haircuts depend on weather conditions, soil characteristics, the condition of the grass cover and season. The last haircut should be made in the middle of autumn. And in the future, start preparing the lawn for wintering.

So, to ensure that the country or personal plot is decorated with a beautiful green lawn, you can, if regularly care for it and correctly trimmed. It is important not to miss the moment of the first haircut, otherwise in the future the site will begin to overgrown with weeds, and the plants grow and develop incorrectly. The tool with which the lawn should be cut, based on the size of the site, your own experience and capabilities.